Professional Documents
Culture Documents
Maintenance of BCH
Maintenance of BCH
Maintenance of BCH
Compressor
Maintenance
Safety first
5. INTERMEDIATE CASING
4. INNER CASING
11. Coupling
1. DIAPHRAGM
10. BEARING 2. LABYRINTH
2.Assembly of labyrinth
8. Assembly of Bearing
Flow chart of compressor assembly
1.Assembly of diaphragm
2.Assembly of labyrinth
8. Assembly of Bearing
1. Assembly of diaphragm
1.Set diaphragm on inner casing
(刻印に合わせ組込)
Diaphragm
3.Check level
(段差測定)
Bearing
Flow chart of compressor assembly
1.Assembly of diaphragm
2.Assembly of labyrinth
3.Measurement for Labyrinth clearance
8. Assembly of Bearing
2. Assembly of Labyrinth
3.Confirm no discrepancy
(食い違いの確認)
5.Installation of inner casing
1. Set guide rail 2.Hook up inner casing horizontally
(水平に吊る)
3.Set inner casing on guide rail 4.Install casing using Special tool
(ガイドレールとインナーケースを合わせる) (押込み冶具のセット)
5.Installation of inner casing
1.After install inner casing to
balance labyrinth position,
lift up the shaft a little.
(バランスラビリンスまで押し込んだら
シャフトを少し吊り上げる)
Protection of casing
Guide bolt
Outside diameter
position
9.Assembly of Coupling HUB
7.Check outer diameter of rotor (押し込み前の外形寸法測定)
(指定押し込み量後外形変形量の確認)
(1)Keep pressure on pushing side
(2)Release pressure on expanding side
(1)押し込み側圧力は、其のままキープする
(2)拡大側圧力は、“0” とする
9.Assembly of Coupling HUB
11.After one hour, measure outer diameter of
hub.
(1時間後外径変形値の測定)
Confirmation
①Outside diameter
②Amount of pushing.
(専用工具を使用してナットを締め付ける)
(0.2~0.3㎜のライナーを入れる)
(2) Measuring of Bearing Clearance.
(シャフトに鉛線を取り付ける)
シャフトに鉛線を取り付ける)
(セットボルトとパットの隙間は、1.0~2.0
セットボルトとパットの隙間は、1.0~ 2.0 mmとする
mmとする))
It confirms for surface
Rotation instruction confirmation
(合わせ面の手入れ)
合わせ面の手入れ)
(回転方向を合わせる)
回転方向を合わせる)
Confirmation of position
(ノックボルトを入れセットボルトを締付ける)
ノックボルトを入れセットボルトを締付ける)
(位置ずれの確認)
位置ずれの確認) (締付けトルクトルクの近い数値で)
締付けトルクトルクの近い数値で)
Lead wire
Measurement
Confirmation of mark
set screw
Attaches set
Fixation of RTD
Fixation RTD line
Assembly of bearing cap
(カップリング図面の確認)
(組付け部品のチェック)
(ダイヤフラム面とガード面を合わせる)
Rubber hammer
The suitable mark of the hub and guard. It puts it until the coupling bolts entertain
(ハブとガードの合いマークを合わせる)
ハブとガードの合いマークを合わせる) (カップリングボルトを締付けるまで)
カップリングボルトを締付けるまで)
Monitor
Flow chart of balance work
Balance of impeller
Balance of shaft
Integrated balance
Balance of unit
Shaft
Size confirmation
Integrated balance
14. Axis vibration measurement