Professional Documents
Culture Documents
FL - Nichlf.: Service Manua Service Manual
FL - Nichlf.: Service Manua Service Manual
Contents
1. INTRODUCTION 5
2. SAFETY INSTRUCTIONS 5
2.1. Warnings 5
2.3. Symbols 6
3. DESCRIPTION 7
3.2. Description 7
5. MAINTENANCE A N D CLEANING 11
5.1. Maintenance 11
5.2. Cleaning 11
7. COMPONENT POSITIONS 15
This publication can only be reproduced, transmitted, transcribed, or translated 7.2. POSITIONING OF CCU 15
into any human or computer language with the written consent of NICAL S.P.A.
8. STANDARD INSTALLATION 17
This manual in English is the original version.
8.1. Camera Head (CCD head adjustments) 17
9.2. Command 24
10.5. Multiple cinc-loop mode without position reset (ADD5=0, ADD1=0, ..) 29
10.6.Multiple cine-loop mode with position reset (ADD5=0, A D D 1=0, ..) 30 2 SAFETY INSTRUCTIONS
10.7. Erasing memory mode (ADD5=0, A D D 1 = 1, ADD0=0) 31 NICAL S.p.A. accepts no responsibility for any misuse of the CCD camera N23
outside of its original design and description as set forth in manual.
11. ELECTRICAL DIAGRAMS 31 Furthermore NICAL S.p.A accepts no responsibility for any damages to camera,
operator, and patient, due to incorrect installation or unauthorized modification
11.1. General circuit diagram and block diagram of N23 CCD system. 31 (mechanical or electrical) and misuse of N23 CCD system.
2.1 Warnings
1. Read these instructions carefully. Save these instructions for future
reference.
2. Follow all warnings and instructions marked on the product.
3. Slots and openings in the cabinet are provided for ventilation; to ensure
reliable operation of the product and to protect it from overheating, these
openings must not be blocked or covered.
4. This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
NICAL Company.
5. When the CCD camera is turned on make a white test in according to verify
the quality image.
> Iron, copper, lead, aluminium, non-biodegradable plastics, and fiber of glass
printed circuit boards.
Business users should contact their supplier and check the terms and c o n d i t i o n s of
the purchase contract. T h i s product should not be m i x e d with other c o m m e r c i a l
wastes for disposal.
3.2 Description
Symbols
Symbol
Description
— Direct current
R e v . 2 N o v e m b e r 2005
Page 7/33
N23 CCD CAMERA i^NIEHLfj:
Service manual ' 5
C C D Camera Head
C C D Type; Vz' Interline low blooming C C D sensor (470.000 pixels)
Integrated optical lens system: High resolution with adjustable focus and diaphragms
Image intensifier output screen: From 15 to 40mm diameter.
Mourning frames: From 6" inch to 16'' inch 1.1.
C C D / C C U Characteristics
Resolution. 20 lines-pairs (on 6" image intensifies)
Gamma correction: 0.4 or 1
Video output A/D converter: 10 bits
Video Bandwidth: 20 M H z ± 3dB
DRF (Dynamic Recursive Filler): Yes ( N 2 3 H )
MD (Motion Detection): Yes ( N 2 3 )
Standard Recursive filter: Factor 2,4,8,16
Memory: 16 bits
Automatic video level compensation: Yes
Automatic \-ray kV/mA compensation: Yes. Analog and digital (up/down)
Dynamic contrast compensation for better image uniformity: Yes (shading)
Very high dynamic video amplifier: Yes
High precision electronic circle: Yes
Video output signal: \ Vpp (0.3 Vpp Sync)
Operating conditions
Working temperature range: 10-Cto f45 C
Stoic temperature range. -40 C ю + 5 5 ° С
JA
' GK IS 1МТК\ТЮ\'Л!.|.у LOT B L A N K
,J
The system will serve you well if you Lake care of it.
Maintenance guide
Frequency Description
2 years Cable connection and condition inspection
1 year Image quality check
5.2 Cleaning
COMPONENT POSITIONS
NOTE: For best performance it's better to insulate the camera head from the
ground system. For this reason the camera head has a special superficial
treatment to insulate the head when it is fixed with screws to the system. Be sure
to use plastic insxnation with screw to fix head at the system.
Line up holes at the bottom of the cover CCU and fasten with screws to the system.
N I C A L C O M P A N Y D O E S N O T P R O V I D E T H E S E T S C R E W S
m in пг—in ,
I S ixiEXLIT > \ . М : . V l k l i b l a n k
8 STANDARD INSTALLATION
il Mi 'Will M u l l - . I ) II I \ .
! 1
> < ' ! S < >!•'
:
! ! I!: i * 'I > ( Л М К К Л i 1'
1 ,::\ .и i i - s i i i i i i i n I i I' 11
\,.\..-ii.l>. i .ЧШ-
N23 CCD CAMERA ^NICHLj^ N23 CCD CAMERA
Service manua Service manual
SHADING
Using correct dose uniformity, regulate the trimmers P7, P8, P9 е PIO until to
obtain on the monitor the maximum uniformity.
1 MP@ftEFX№M
Jl is used to enable the Rlark Level Auto Control. T h e jumper J4 enables or rejects this regulation.
SW2 AUTO BLK
ISW2 ON: position 1 2)
Ad just black level pedestal (BOTTOM BLACK). When Auto BLK off (SW2 OFF:
R157 BLACK LEVEL
position 2.3) regulate the pedestal to 30mV respect referring level KV AUTO
BLACK LEVEL A d j u s t black level pedestal (BOTTOM BLACK). When Auto BLK on (SW2 ON:
R156
AUTO CONTROL position 1 2) regulate the pedestal to 30 mV respect referring level.
11 is used to enable the Auto White Love] It is possible to change the answer sensibility of control system dose. In according
SW3 AUTO WTH
(SW3 ON: position 1-2) lo change the sensibility, use trimmer P l l . The trimmer P4 changes the action
AUTO A d j u s t white level (TOP WHITi;). Set to 590mV video analog signal respect
R163
WHITE LEVEL referring level. Use jumper SW3=ON (position 1-2) to select or re|ect this feature.
point of the control (video level).
R94 GAMMA Factory adjusted
ANALOG VIDEO (2-3)
/SYNC PULSE FOR
It is used to enable on Video 1 ati analogic signal: (position 2-3) or an output al CIRCLE
SW4
25Hz/30Hz square wave (position 1 -2) used as sync pulse in high contrast
PULSED FLUORO (1-2)
GAMMA Juniper J6 position 1 2: gamma value is 0. 4.
J6
CORRECTION dumper J6 position 2-3: gamma value is 1
Using trimmer P6 it is possible to change the diameter of video circle. The trimmer
SHADING
11 is used to enable shading regulations
P5 regulates the circle area where it finds the dose automatic control (ROI). In
J4
ENABLE
Set the shading gain to compensate picture not uniformity because o f i m a g e
according to select the video or the auto circle move the j u m p e r J 2 . The trimmers
SHADING
P7-P8-P9-P10
(VS-VP-HS-HP] Intensifier. Use lumper .J4-ON (position 2-31 to select or reject this feature P I , P2 and P3 regulate the centering and the symmetry.
VIDEO & AUTO It is used to enable the video and auto video regulations
J2
CIRCLE ENABLE J2 position 3-4: V I D E O CIRCLE: .12 position 2-3 AUTO CIRCLE
Adjust circle blanking diameter. Use jumper J 2 - O N (position 3-4) to select or G A M M A CORRECTION
P6 VIDEO CIRCLE
reiecl this feature
Adjust measurement circle area used hy automatic gain and x-ray KV control
AUTO CIRCLE
PB
Use jumper J2=ON (position 2-3) to select or reject this feature It is possible change the gamma value. Moving j u m p e r J6 in position 1-2 the
P3 CIRCLE SIMMETRY
Adjust till' symmetry of video circle. Use jumper J 2 - O N (position 3-4) to select or gamma level corresponds to 0, 4; while moving j u m p e r J6 in position 2-3 the
rejeel this feature
Adjust the vertical centering of video circle. Use jumper J 2 - O N (position 3 4) to gamma level is equal to 1.
PI VERT SHIFT
select or reject this feature
Adjust the horizontal centering of video circle. Use jumper -J2-ON (position 3 4) to
P2 HOR SHIFT
select or reject this feature V I D E O 1 OUTPUT
P4 AUTO KV LEVEL Set the value of AUTO KV
Increase or decrease the sensibility of the automatic KV control. This feature is
Pll AUTO KV WINDOW very usetul in according to adapt the CCD camera N23 for any kind of X ray
On BNC VIDEO 1 are possible changing two signals:
generator Analogic video l V p p 7 5 0 . or a square wave signal 5Vpp at 25Hz/30Hz in according
Position 2-3: Automatic reset when system turned -on.
ROTATION RESET (CCD
Position 1-2: Manual reset. To bring camera head to 0 position ground pins CW to sync x-ray systems in pulsed fluoroscopy.
J5 CAMERA WITH ROTATION
ONLY)
(pin 17) and CCW (pin 4) on interface connector DB25 at the same time. To obtain the analogic video move jumper SW4 in position 2-3; while to obtain the
Location: N23 MHO.
square wave signal move j u m p e r SW4 in position 1-2.
ROTATION
8.5 Factory set up only
In the systems where the CCD camera head has the rotation:
1. Manual reset. (Factory default). Jumper J5 position 1-2. To bring camera 1
head to 0 position ground pins CW (pin 17) and CCW (pin 4) on interface
connector DB25 at the same time.
2. Automatic reset when system turned on. Jumper J5 position 2-3.
N23_ANB1
V I D E O A U T O LEVEL
'CODB*
v
R74
i <*"&&Jlto*
WHITE LEVEL
-
(Set i n factory)
т W
diffusion radiation. Using a phantom which simulates human body, regulate this
trimmer unlil to obtain a good black-level when it presents diffusion radiation. It is
R44 B L A C K O F F S E T (Set i n factory) possible reject this automatic control moving the jumper SW2 (position 1-2: on;
R97 R E S O L U T I O N (Set i n factory) position 2-3: OFF).
The trimmer R163 regulates the level of white automatic control (WH). Using a
WHITE SPOT ERASURE FEATURE standard phantom and with white automatic control on regulate this trimmer until
to obtain a correct video signal. It is possible reject this control by jumper SW3
H O W TO DETECT (position 2-3) and also by the command AUTO-OFF (pin 2 25DB connector).
то
FEMALE
(SOLDERING VIEW)
сл z
CDГ О
~-oo
§ ao
ш3
m
33
>
DC
PIN 6
Power Supply
M2
PIN 2
Command motor 2
R0 C o m m a n d rotation
PIN 3 0
GND Ground video
PIN 9 signal
to
VIDEO
PIN 5
V i d e o signal
Г
N23 CCD C A M E R A NICBL
N23 C C D C A M E R A Service manual • 1 3
Service manua
O U T = + 18V IF D O S E IS T O O H I G H .
+KV OUT 15
OUT= 0V IF DOSE IS CORRECT OR TOO LOW.
AUTO-OFF
ANALOG KV CONTROLL. OUT= 0-H2 V.
+KV
O U T = 0V IF DOSE IS T O O LOW.
CONTROL OUT 16
OUT = 12V IF D O S E IS T O O H I G H .
KV CONTROL O U T = 6V IF D O S E IS BALANCED.
Page 24/33
Rev. 2 N o v e m b e r 2005 Rev. 2 November 2005 Page 25/33
N23 CCD CAMERA N23 CCD CAMERA
Service manua Service manual - - = ^ J S P »
1
• Direct access mode. Allows the recording or display of the first 32 positions of
memory.
• Manual selection mode. Allows the user to move indicator to desired position
to guarantee recording/playback at a specific position.
• Multiple Cine-Loop mode without reset. Allows the recording/ playback of
images in sequential order at a selected speed starting from actual indicator
position.
• Single Cine-Loop Mode with reset. Allows the recording/playback of images in
sequential order at a selected speed starting from initial (first) indicator
position.
• Erasing Memory. Allows the erasing of the full memory.
MWR DESCRIPTION
Memory Write. If MWR= GND user can record an image to the memory.
The video input (Live or LIH) present on BUS is transferred to the memory
0
at the position where indicator is found and with selected mode. (See list
of modes.)
Memory Read. If MWR= OPEN (1) user can playback an image from the
memory. The frame displayed will correspond to indicator position at this
1 time. The frame will be transferred to BUS with selected mode. (See list of
modes.)
\
l 1 X 0 Read rmynory frames and images are transferred on monitor Л ( U P ) The indicator of frame memory position is
1 1 1 0 moved to tite next s u c c e s s i v e position, (position <=
position-*-1)
l X 1 0 Read memory frames and images are transferred on monitor В
\
CLK
( D O W N ) The indicator of frame memory position is
1 0 1 0 moved to p r e c e d i n g frame in memory. ( positioti
l 1 1 0 Read memory frames and images are transferred on troth monitor A and В position-1)
CLK
\ o
( R E S E T ) The indicator of frame memory position is
X 0 X X FREEZE A. [mage on monitor A frozen. X X 1 moved to i n i t i a l frame of stored image sequence,
(position = 1)
If MWR-0 the image on the BUS (Live or LIH) is MULTIPLE CINE-LOOP MODE WITHOUT RESET
recorded at the first position.
1 1 1 l 1
If MWR =1 the recorded image is read at position 1 and In this mode the record/playback starts from the
transferred to BUS for display actual position found. (MWR) increasing frame hy
frame automatically at the selected speed rate. In
X X X 0 1
this mode it is possible to acquire a series of
1 1 1 l 0 Same as above record/read memory at position 2 different segmented images at various times. During
a successive playback of all ttie images in the
memory it is possible to read the different phases of
1 1 1 0 1 .Same as above record/read memory at position 3 an exam recorded at different times.
Speed 2 5 ( 3 0 ) F r a m e s p e r s e c o n d
1 1 1 0 0 Same as above record/read memory at position 4 When M W R = 0 images are acquired into the memory
1 1 1 0 1 at 25 (30) fps. Starts at actual position of indicator.
When M W R = 1 images are read (playback) from
1 1 0 1 1 Same as above record/read memory at position 5 memory at 25 (30) fps. Starts at actual position of
indicator.
1 1 0 o 1 Soeedl2 ( 1 5 ) f p s
1 1 0 1 0 Same as above record/read memory at position в
1 0 1 0 1 Speed 6 f p s
0 1 1 0 1 Speed 1 fps
0 0 0 0 0 Same as above record/read memory at position 32
0 1 0 0 1 Speed 0.5 fps
0 0 l 0 l Speed 0 . 2 5 f p s
liill erasing ini'mni'y it' signals amtempoiary CiNU moie (hail
Single Shot II 1
When M W R = 0 images are acquired into the memory N23_CON0 Conversion board diagram, standard video and inversion
l l 1 0 0
al 25 (30| fps starting at position = 1. Memory frames diagram
N 2 3 _ M E M 1
When M W R = 1 images are read at 25 (30) fps
starting at posilion=l. NCD_XCD01 CCD sensor block
l l 0 0 0 Soeedl2 (15)fps NCD_XCD02 Power supply board C C D head
l 0 1 0 0 Speed 6 f p s
l 0 0 0 0 Speed 3 f p s
0 1 l 0 0 Speed 1 f p s
0 1 0 0 0 Soeed 0.5 f p s
0 0 l 0 0 Speed 0.25 f p s
Single Shot
When M W R = 0 The memory acquires O N E image only
starting til position = 1
0 0 0 When MWR=1 only O N E image is read from (he
0 0
memory at position=].