Professional Documents
Culture Documents
Toggle Clamp Latch Type
Toggle Clamp Latch Type
DISTRIBUTED BY
PRISUN TECHNOLOGIES
prisuntechnologies@gmail.com / info@prisun.in
INTRODUCTION TO TOGGLE CLAMPS
MI
What is a Toggle Clamp
A toggle clamp is a fastening device that usually
consists of a handle to control the device , A holding bar
to grip the work piece , and a linkage system of pivot pins
and levers to boost the applied force once engaged
the toggle clamp essentially becomes locked.
A toggle clamp typically serves to secure an object tightly
in order to prevent it from moving or separating when
inward pressure is applied.
Toggle Actions
Toggle action principle operate through the linkage system
of levers and pivots, The fixed length levers are connected by the
pivot pins which supply the action and clamping force.
Toggle action as an over center lock position once its in the
over center position the clamp cannot move or unlock
unless the linkage is moved
Holding Capacity
All MI Toggle clamps are selected by their holding capacity
each toggle clamp are tested in all aspects and the holding capacity
is calculated when toggle clamp locked in closed position without
creating permanent deformation, Force is measured at the closest point
to the base and diminishes as the end of the bar reached
Clamping Force
Clamping force is the force applied while closing the clamp
which is measured between the bar and the component
clamping force cannot be calculated exactly as it depends
on operator and clamping position of component
1
VERTICAL HOLD DOWN TOGGLE CLAMPS
MI
applications
2
ABOUT MI- VERTICAL TOGGLE CLAMP
MI
3
2
4
5
1. HAND GRIP - Grip made up of Nitrile having large grip surface with oil resistence this assures the safety and comfort to the operator
why use nitrile rubber on toggle clamps : Good compression , Resistance to heat , Resistance to abrasion , Resistance to water
Resistance to gas permeability & This rubber Grip comes with all models of MI Brand
PART NO DESCRIPTION
2. RIVETS - Its made up of high durable material which runs with specially designed hardened steel bushes EXAMPLE (MI-V-50-FU)
MI - MECHENGG INDUSTRIES
V - VERTICAL
3. HARDENED BUSHES - Hardened steel bushes was specially designed for high durability smooth operation 50 - HOLDING CAPCITY
FU - FLANGED BASE U SHAPED HOLD DOWN ARM
and provide more life cycle for toggle clamp This applies for all model part no’s
4. CLAMPING SCREW - Screw (8.8) bonded with nitrile rubber with large flat surface with maximum tensile strength
which is supplied with flanged washers and flat nuts
5. STOP PIN - The opening angle of the toggle clamp can be changed by pressing in a stop pin
3
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FU
MI
Vertical clamp with flanged base u shaped hold down arm
which is supplied with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
FU - refers to Flanged base U shaped hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
adjustable u arm
MI - V - 50 - FU 85 55.62 15.55 15 24 25 34 30.62 4.5 21.82 5 5 5 89° 60° — — 230 500 0.68
MI - V - 150 - FU 159 109 35 19 39 36 53 67 7 50 8 10 9 73° 50° 130° 70° 700 1500 0.351
MI - V - 250 - FU 203.82 133.7 38.49 26 44 44 64 89.7 8.5 62.5 10 10 9 85° 54° 134° 71° 1250 2500 0.573
MI - V - 350 - FU 218.15 147 47.62 31 50 49 68 98 8 71.96 10 9 9 50° 40° 107° 59° 1750 3500 0.796
MI - V - 450 - FU 236.32 172.18 47.72 32 48 56 68 116.18 9 82.16 12 10 12 58° 52° 124° 76° 2250 4500 1.021
MI - V - 550 - FU 313 218 89 45 64 76 96 142 12.5 107.21 16 16 15.5 41° 33° 77° 43° 2750 5500 2.250
4
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-SU
MI
Vertical clamp with straight base u shaped hold down arm
which is supplied with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
SU - refers to Straight base U shaped hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 50 - SU 97.14 55.62 27.71 15 — 25 4 30.62 4.5 21.82 5 5 5 89° 60° — — 230 500 0.68
MI - V - 100 - SU 130.93 69.8 35.93 14 — 26 6 43.8 5 29 6 6 6 81° 56° — — 450 1000 0.151
MI - V - 150 - SU 172 109 54 19 — 36 6 67 7 50 8 10 9 73° 50° 130° 70° 700 1500 0.351
MI - V - 250 - SU 227.96 133.7 62.71 26 — 44 8 89.7 8.5 62.5 10 10 9 85° 54° 134° 71° 1250 2500 0.573
MI - V - 350 - SU 243.08 147 72.57 31 — 49 8 98 8 71.96 10 9 9 50° 40° 107° 59° 1750 3500 0.796
MI - V - 450 - SU 260.25 172.18 71.66 32 — 56 10 116.18 9 82.16 12 10 12 58° 52° 124° 76° 2250 4500 1.021
MI - V - 550 - SU 349.7 218 125.73 45 — 76 10 142 12.5 107.21 16 16 15.5 41° 33° 77° 43° 2750 5500 2.250
5
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FS
MI
Vertical clamp with flanged base solid hold down arm
which is supplied with spindle assemblies , bolt retainer
high grade orange rubber grip having large grip surface with oil & heat resistance
FS - refers to Flanged base Solid hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
flanged base
solid arm
MI - V -150 - FS 159 110 35 19 8 39 36 53 68 7 25.60 16 10 10 6 73° 50° 130° 70° 700 0.351
MI - V - 250 - FS 203.82 140.98 38.49 26 10 44 44 64 96.98 8.5 32 20 10 9 8 85° 54° 134° 71° 1250 0.573
MI - V - 350 - FS 218.15 153.12 47.62 31 10 50 49 68 104.12 8 33.60 21 9 9 8 50° 40° 107° 59° 1750 0.796
MI - V - 450 -FS 236.32 177.9 47.72 32 12 48 56 68 121.9 9 40 25 10 12 10 58° 52° 124° 76° 2250 1.021
6
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-SS
MI
Vertical clamp with straight base solid hold down arm
which is supplied with spindle assemblies , bolt retainer
high grade orange rubber grip having large grip surface with oil & heat resistance
SS - refers to Straight base Solid hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
straight base
solid arm
MI - V - 150 - SS 172 110 54 19 8 — 36 6 68 7 25.60 16 10 10 6 73° 50° 130° 70° 700 0.351
MI - V - 250 - SS 227.96 140.98 62.71 26 10 — 44 8 96.98 8.5 32 20 10 9 8 85° 54° 134° 71° 1250 0.573
MI - V - 350 - SS 243.08 153.12 72.57 31 10 — 49 8 104.12 8 33.60 21 9 9 8 50° 40° 107° 59° 1750 0.796
MI - V - 450 - SS 260.25 177.9 71.66 32 12 — 56 10 121.9 9 40 25 10 12 10 58° 52° 124° 76° 2250 1.021
7
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FF
MI
Vertical clamp with flanged base fixed hold down arm
which is supplied with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
FF - refers to Flanged base Fixed hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
flanged base
non adjustable arm
MI - V - 250 - FF 203.82 142.7 38.49 26 44 44 64 98.7 8.5 — 10 10 9 85° 54° 134° 71° 1250 0.573
MI - V - 350 - FF 218.15 152.81 47.62 31 50 49 68 103.81 8 — 10 9 9 50° 40° 107° 59° 1750 0.796
MI - V - 450 - FF 236.32 179 47.72 32 48 56 68 123 9 — 12 10 12 58° 52° 124° 76° 2250 1.021
8
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-SF
MI
Vertical clamp with straight base fixed hold down arm
which is supplied with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
SF - refers to Straight base Fixed hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 250 - SF 227.96 142.7 62.71 26 — 44 8 98.7 8.5 — 10 10 9 85° 54° 134° 71° 1250 0.573
MI - V - 350 - SF 243.08 152.81 72.57 31 — 49 8 103.81 8 — 10 9 9 50° 40° 107° 59° 1750 0.796
MI - V - 450 - SF 260.25 179 71.66 32 — 56 10 123 9 — 12 10 12 58° 52° 124° 76° 2250 1.021
9
VERTICAL HOLD DOWN TOGGLE CLAMPS
T-SERIES - MI-V-TFU
MI
Vertical t handle flanged base with u shaped hold down arm
clamp is furnished with spindle assemblies , flanged washers & t grip with oil & heat resistance
this series is mainly suitable for height restricted space conditions
FU - refers to Flanged base U shaped hold down arm & T - refers to T handle
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 150 - TFU 118 86 109 35 19 39 36 53 67 7 50 8 10 9 73° 50° 130° 70° 700 1500 0.351
MI - V - 250 - TFU 142.26 125.72 133.7 38.49 26 44 44 64 89.7 8.5 62.5 10 10 9 85° 54° 134° 71° 1250 2500 0.573
MI - V - 350 - TFU 159.26 126.15 147 47.62 31 50 49 68 98 8 71.96 10 9 9 50° 40° 107° 59° 1750 3500 0.796
MI - V - 450 - TFU 174.37 128.15 172.18 47.72 32 48 56 68 116.18 9 82.16 12 10 12 58° 52° 124° 76° 2250 4500 1.021
10
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-TSU
MI
Vertical t handle straight base with u shaped hold down arm
clamp is furnished with spindle assemblies , flanged washers & t grip with oil & heat resistance
this series is mainly suitable for height restricted space conditions
SU - refers to Straight base U shaped hold down arm & T - refers to T handle
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 0150 - TSU 131 86 109 54 19 — 36 6 67 7 50 8 10 9 73° 50° 130° 70° 700 1500 0.351
MI - V - 0250 - TSU 166.4 125.72 133.7 62.71 26 — 44 8 89.7 8.5 62.5 10 10 9 85° 54° 134° 71° 1250 2500 0.573
MI - V - 0350 - TSU 184.18 126.15 147 72.57 31 — 49 8 98 8 71.96 10 9 9 50° 40° 107° 59° 1750 3500 0.796
MI - V - 0450 - TSU 198.3 128.15 172.18 71.66 32 — 56 10 116.18 9 82.16 12 10 12 58° 52° 124° 76° 2250 4500 1.021
11
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FSB
MI
Vertical flanged base solid hold down bar
these toggle clamps have solid bar this bar can be cutted in to any preferred size
and it can be drilled in any preferred position or a clamping assembly can be welded to the bar as per the application
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
FSB - refers to Flanged base Solid hold down Bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 150 - FSB 158 107 36 19 38 36 51 71 7 16 6.5 8.5 73° 50° 130° 70° 1200 2000 0.500
MI - V - 350 - FSB 218.15 153.5 48 31 50 49 68 98.5 8 20 9 9 50° 40° 107° 59° 2750 3900 1.352
MI - V - 450 - FSB 236.32 183 50 32 48 56 68 122 9 22 10 12 58° 52° 124° 76° 2250 5000 1.952
12
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-SSB
MI
Vertical straight base solid hold down bar
these toggle clamps have solid bar this bar can be sheared in to any preferred size
and it can be drilled in any preferred position or a clamping assembly can be welded to the bar as per the application
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
SSB - refers to Straight base Solid hold down Bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 150 -SSB 176 107 36 19 36 6 71 7 16 6.5 8.5 73° 50° 130° 70° 1200 2000 0.500
MI - V - 350 - SSB 243 153.5 48 31 49 8 98.5 8 20 9 9 50° 40° 107° 59° 2750 3900 1.352
MI - V - 450 - SSB 259 183 50 32 56 10 122 9 22 10 12 58° 52° 124° 76° 2250 5000 1.952
13
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FMU
MI
Vertical front mount with U shaped hold down arm
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses
which is furnished with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
FMU - refers to Front Mount with U shaped hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
FRONT MOUNT Customized clamps
ADJUSTABLE ARM
MI - V - 100 - FMU 154 69.8 64 18 41 30 54 40 5 29 6 6.5 8.5 81° 56° — — 450 1000 0.151
MI - V - 150 - FMU 198 109 76 19 39 45.5 57 63 7 48 8 9 8.5 73° 50° 130° 70° 700 1500 0.351
MI - V - 350 - FMU 255 153 84.6 34 46 60 64 93 8 72 10 9 8 50° 40° 107° 59° 1750 3500 0.796
14
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FMF
MI
Vertical front mount with fixed hold down arm
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
FMF - refers to Front Mount with Fixed hold down arm
application C
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FRONT MOUNT FOR ALL BELOW MODELS
FIXED HOLD DOWN ARM Customized clamps
MI - V - 100 - FMF 154 69.8 64 18 41 30 54 44 5 6 6.5 8.5 81° 56° — — 450 1000 0.151
MI - V - 150 - FMF 198 109 76 19 39 45.5 57 67 7 8 9 8.5 73° 50° 130° 70° 700 1500 0.351
MI - V - 350 - FMF 255 153 84.6 34 46 60 64 99 8 10 9 8 50° 40° 107° 59° 1750 3500 0.796
15
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FMS
MI
Vertical front mount with solid hold down arm
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses
which is furnished with spindle assemblies and bolt retainer
high grade orange rubber grip having large grip surface with oil & heat resistance
FMS - refers to Front Mount with Solid hold down arm
application
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
FRONT MOUNT
SOLID ARM
MI - V -150 - FMS 198 112 76 19 8 39 45.5 57 67 7 25.60 16 9 8.5 6 73° 50° 130° 70° 1500 0.351
MI - V - 350 - FMS 255 159 85 34 10 46 60 64 99 8 33.60 21 9 8 8 50° 40° 107° 59° 3500 0.796
16
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-FMSB
MI
Vertical front mount with solid hold down bar
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses these toggle clamps have solid bar
this bar can be sheared in to any preferred size and it can be drilled in any preferred position
or a clamping assembly can be welded to the bar as per the application
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
FMSB - refers to Front Mount with S solid hold down Bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - V - 100 - FMSB 154 69.8 64 18 41 30 54 50 5 10 6.5 8.5 81° 56° — — 450 1000 0.151
MI - V - 150 - FMSB 198 109 76 19 39 45.5 57 68 7 16 9 8.5 73° 50° 130° 70° 700 1500 0.351
MI - V - 350 - FMSB 255 153 84.6 34 46 60 64 94 8 20 9 8 50° 40° 107° 59° 1750 3500 0.796
17
VERTICAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-V-HSC
MI
Vertical compact heavy duty model
which is furnished with spindle assemblies
this series is designed for maximum opening to simplify jig loading & for most rugged production jobs
this has an deeper throat depth and more height under the clamping bar
high grade orange rubber grip having large grip surface with oil & heat resistance
this heavy duty model comes with casted arm
HSC - refers to heavy duty with Solid Casted bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
18
ABOUT MI HORIZONTAL TOGGLE CLAMP
MI
PART NO DESCRIPTION
19
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-FU
MI
horizontal clamp with flanged base u shaped hold down arm
which is furnished with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
FU - refers to Flanged base U shaped hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H - 75 - FU 45.5 146.36 28 19 19.4 30 30 54.78 5.5 25.42 5 5.3 5.5 79° 53° 360 750 0.131
MI - H - 150 - FU 46 159.14 31.3 24 23.4 35 34 65.61 5.5 35.91 6 5.3 5.5 79° 53° 750 1500 0.211
MI - H - 250 - FU 54 189.67 35.5 29.5 26.6 45 40 73.23 6.6 43.87 8 6.7 7.7 87° 53° 1250 2500 0.293
MI - H - 350 - FU 80 273.21 49.56 39.5 38 60 55 112.59 8.5 67.92 12 8.5 10.25 89° 56° 1750 3500 0.777
MI - H - 650 - FU 97 329.52 61.99 45 44 72 64 143.46 9.5 82.02 12 10 13.5 79° 58° 3250 6500 1.542
20
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-SU
MI
horizontal clamp with straight base u shaped hold down arm
which is furnished with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
SU - refers to Straight base U shaped hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H - 75 - SU 55.65 146.36 38.23 19 — 30 4 54.78 5.5 25.42 5 5.3 5.5 79° 53° 360 750 0.131
MI - H - 150 - SU 55.5 159.14 41.23 24 — 35 6 65.61 5.5 35.91 6 5.3 5.5 79° 53° 750 1500 0.211
MI - H - 250 - SU 67.5 189.67 48.43 29.5 — 45 6 73.23 6.6 43.87 8 6.7 7.7 87° 53° 1250 2500 0.293
MI - H - 350 - SU 99.2 273.21 67.76 39.5 — 60 8 112.59 8.5 67.92 12 8.5 10.25 89° 56° 1750 3500 0.777
MI - H - 650 - SU 117 329.52 82.05 45 — 72 10 143.46 9.5 82.02 12 10 13.5 79° 58° 3250 6500 1.542
21
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-FS
MI
horizontal clamp with flanged base solid hold down arm
which is furnished with spindle assemblies and bolt retainer
high grade orange rubber grip having large grip surface with oil & heat resistance
FS - refers to Flanged base Solid hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H -150 - FS 46 159.53 31.3 24 6.10 23.4 35 34 66.1 5.5 3 6 5.3 5.5 79° 53° 750 0.211
MI - H - 250 - FS 54 191.09 35.5 29.5 8.10 26.6 45 40 74.64 6.6 3 8 6.7 7.7 87° 53° 1250 0.293
MI - H - 350 - FS 80 273.99 49.56 39.5 10.10 38 60 55 113.92 8.5 4 10 8.5 10.25 89° 56° 1750 0.777
MI - H - 650 - FS 97 329.95 61.99 45 12.10 44 72 64 143.9 9.5 5 12 10 13.5 79° 58° 3250 1.542
22
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-SS
MI
horizontal clamp with straight base solid hold down arm
which is furnished with spindle assemblies , bolt retainer
high grade orange rubber grip having large grip surface with oil & heat resistance
SS - refers to Straight base Solid hold down arm
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H - 150 - SS 55.5 159.53 41.23 24 6.10 23.4 35 6 66.1 5.5 3 6 5.3 5.5 79° 53° 750 0.211
MI - H - 250 - SS 67.5 191.09 48.43 29.5 8.10 26.6 45 6 74.64 6.6 3 8 6.7 7.7 87° 53° 1250 0.293
MI - H - 350 - SS 99.2 273.99 66.92 39.5 10.10 38 60 8 113.92 8.5 4 10 8.5 10.25 89° 56° 1750 0.777
MI - H - 650 - SS 117 329.95 82.08 45 12.10 44 72 10 143.9 9.5 5 12 10 13.5 79° 58° 3250 1.542
23
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-FF
MI
horizontal clamp with flanged base fixed hold down bar
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
FF - refers to Flanged base Fixed hold down bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H -75 - FF 45.5 145.66 28 19 19.4 30 30 54.8 5.5 — 5 5.3 5.5 79° 53° 360 0.131
MI - H - 150 - FF 46 159.37 31.3 24 23.4 35 34 65.84 5.5 — 6 5.3 5.5 79° 53° 750 0.211
MI - H - 250 - FF 54 191.15 35.5 29.5 26.6 45 40 74.7 6.6 — 8 6.7 7.7 87° 53° 1250 0.293
MI - H - 350 - FF 80 273.16 49.56 39.5 38 60 55 113.9 8.5 — 12 8.5 10.25 89° 56° 1750 0.777
MI - H - 650 - FF 97 331.12 61.99 45 44 72 64 145.8 9.5 — 12 10 13.5 79° 58° 3250 1.542
24
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
SERIES - MI-H-SF
MI
horizontal clamp with straight base fixed hold down arm
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
SF - refers to Straight base Fixed hold down bar
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
MI - H - 75 - SF 55.65 145.66 38.23 19 19.4 30 4 54.8 5.5 25.42 5 5.3 5.5 79° 53° 360 0.131
MI - H - 150 - SF 55.5 159.37 41.23 24 23.4 35 6 65.84 5.5 35.91 6 5.3 5.5 79° 53° 750 0.211
MI - H - 250 - SF 67.5 191.15 48.43 29.5 26.6 45 6 74.7 6.6 43.87 8 6.7 7.7 87° 53° 1250 0.293
MI - H - 350 - SF 99.2 273.16 67.76 39.5 38 60 8 113.9 8.5 67.92 12 8.5 10.25 89° 56° 1750 0.777
MI - H - 650 - SF 117 331.12 82.05 45 44 72 10 145.8 9.5 82.02 12 10 13.5 79° 58° 3250 1.542
25
HORIZONTAL HOLD DOWN TOGGLE CLAMPS
MI
SERIES - MI-H-FMF
horizontal clamp with front mount fixed hold down arm
which is furnished with spindle assemblies
high grade orange rubber grip having large grip surface with oil & heat resistance
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses
FMF - refers to Front Mount Fixed hold down arm
PART NO : MI-H-250-FMF
Holding Capacity : 2500 N
Approx Clamp weight : 0.335 kg
Handle moves : 53°
Bar opens : 87°
SERIES - MI-H-FMU
horizontal clamp with front mount U shaped hold down bar
which is furnished with spindle assemblies , flanged washers
high grade orange rubber grip having large grip surface with oil & heat resistance
this toggle clamps allow users to mount the clamp on the side of the table / fixtures
to save precious work surface for other uses
FMU - refers to Front Mount with U shapedh old down arm
PART NO : MI-H-250-FMU
Holding Capacity : 2500 N
Approx Clamp weight : 0.335 kg AVAILABLE ON REQUEST
Handle moves : 53° CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Bar opens : 87° Customized clamps
26
COMPACT HOLD DOWN TOGGLE CLAMPS
SERIES - MI-C-FU
MI
compact clamp with flanged base u shaped hold down bar
which is furnished with spindle assemblies , flanged washers
also known as low profile clamps used mainly for light duty applications
AVAILABLE ON REQUEST
CAD DATA BASE AVAILABLE
Black Passivated Clamps
FOR ALL BELOW MODELS
Customized clamps
27
LATCH TYPE TOGGLE CLAMPS
MI
SERIES - MI-L-H
horizontal latch type toggle clamp
which is supplied with hook rod ,lock nuts , square bended u bolt & latch clamp
Horizontal latch clamps are especially suitable for quick closing and fastening of lids and flaps.
The travel path can be set individually at the closing latch.
high grade orange rubber grip having large grip surface with oil & heat resistance
PART NO : MI-L-100-H
HOLDING CAPACITY
100 KG
PART NO : MI-L-250-H
HOLDING CAPACITY
250 KG
28
LATCH TYPE TOGGLE CLAMPS
MI
PART NO : MI-L-400-H
HOLDING CAPACITY
400 KG
PART NO : MI-L-750-H
HOLDING CAPACITY
750 KG
PART NO : MI-L-1000-H
HOLDING CAPACITY
1000 KG
29
LATCH TYPE TOGGLE CLAMPS
MI
SERIES - MI-L-V
VERTICAL LATCH TYPE TOGGLE CLAMP
which is supplied with hook rod ,lock nuts , square bended u bolt & latch clamp
Horizontal latch clamps are especially suitable for quick closing and fastening of lids and flaps.
The travel path can be set individually at the closing latch.
high grade orange rubber grip having large grip surface with oil & heat resistance
PART NO : MI-L-100-V
HOLDING CAPACITY
100 KG
PART NO : MI-L-250-V
HOLDING CAPACITY
250 KG
30
LATCH TYPE TOGGLE CLAMPS
MI
PART NO : MI-L-400-V
HOLDING CAPACITY
400 KG
PART NO : MI-L-750-V
HOLDING CAPACITY
750 KG
PART NO : MI-L-1000-V
HOLDING CAPACITY
1000 KG
31
PUSH PULL TOGGLE CLAMPS
SERIES - MI-TPCM
MI
PUSH PULL TOGGLE CLAMPS (4 MOUNTING) tapered handle
This model features a lost waxed base for strength and vibration damping properties. This model offers excellent
holding capacity while maintaining a low profile. The plunger is ground and oiled for precise fit and smoothness
in movements and has a tapped hole. high grade orange rubber grip having large grip surface with oil & heat resistance
TPCM : refers to Tapered handle Push/pull Cast Mounted
32
PUSH PULL TOGGLE CLAMPS
SERIES - MI-SPCM
MI
PUSH PULL TOGGLE CLAMPS (4 MOUNTING) straight handle
This model features a lost waxed base for strength and vibration damping properties. This model offers excellent
holding capacity while maintaining a low profile. The plunger is ground and oiled for precise fit and smoothness
in movements and has a tapped hole. high grade orange rubber grip having large grip surface with oil & heat resistance
SPCM : refers to Straight handle Push/pull Cast Mounted
33
PUSH PULL TOGGLE CLAMPS
SERIES - MI-PFM
MI
PUSH / PULL FRONT MOUNT TOGGLE CLAMP
This straight line action clamp can be used as a full retractable locator. It can be mounted on a tooling plate with a jam nut,
flush mounted into a threaded hole, or mounted on an optional plate. When flush mounted, the plunger will retract completely away from the work piece.
high grade orange rubber grip having large grip surface with oil & heat resistance
The plunger is groundand oiled for precise fit and smoothness in movement.
pfm : refers to push / pull front mount
PART NO : MI-PFM-80
PLUNGER TRAVEL : 19 mm
HOLDING CAPACITY
80 KG
PART NO : MI-PFM-150
PLUNGER TRAVEL : 57 mm
HOLDING CAPACITY
150 KG
PART NO : MI-PFM-350
PLUNGER TRAVEL : 67mm
HOLDING CAPACITY
350 KG
34
accessories
MI
BOLT RETAINER - BR
PART NO L L2 D2
MI - BR - V150 25.60 16 8.10
MI - BR - V250 32 20 10.10
MI - BR - V350 33.60 21 10.10
MI - BR - V450 40 25 12.10
MI - BR - V550 51.20 32 16.10
MI - BR - H150 22.40 14 6.10
MI - BR - H250 25.60 16 8.10
MI - BR - H350 35.20 22 10.10
MI - BR - H650 44.80 28 12.10
PART NO A B C
MI - FW - V050 17.90 6.5 9.80 FLANGED WASHERS - FW
MI - FW - V100 17.90 6.5 12
MI - FW - V150 22.50 8.5 15
MI - FW - V250 25.70 11 20 B
MI - FW - V350 25.70 11 20
MI - FW - V450 31.7 12.5 22.70 C
MI - FW - V550 34.7 16.5 29.5
MI - FW - H075 17.90 6.5 11
MI - FW - H150 22.50 8.5 14
MI - FW - H250 22.50 8.5 15 A
MI - FW - H350 25.70 11.0 20
MI - FW - H650 31.70 12.50 25
MI - FW - C050 15.9 6.5 11.5
MI - FW - C150 19.9 8.5 15.5
MI - FW - C350 24.9 11.5 20.5
35
HANDWHEELS
MI
36
ALUMINIUM HANDWHEELS
MI
L2
Material :
Aluminium
4. Different Colour’s
Aluminium Handwheels Without Handle Without Slot
PART NO D1 D2 D3 L1 L3 NO OF APPROX WEIGHT
SPOKES KGS
MI - AL - 80 - 10 - 0 80 10 24 16 29 3 0.100
MI - AL - 80 - 12 - 0 80 12 24 16 29 3 0.100
MI - AL - 100 - 10 - 0 100 10 26 17 30 3 0.160
MI - AL - 100 - 12 - 0 100 12 26 17 30 3 0.160
MI - AL - 125 - 12 - 0 125 12 28 18 36 3 0.265
MI - AL - 125 - 14 - 0 125 14 28 18 36 3 0.265
MI - AL - 160 - 14 - 0 160 14 39 20 40 3 0.415
MI - AL - 160 - 16 - 0 160 16 39 20 40 3 0.415
MI - AL - 200 - 18 - 0 200 18 40 24 45 3 0.855
MI - AL - 200 - 22 - 0 200 22 40 24 45 3 0.855
MI - AL - 250 - 22 - 0 250 22 50 28 51 5 1.600
MI - AL - 250 - 26 - 0 250 26 50 28 51 5 1.600
37
ALUMINIUM HANDWHEELS
MI
Aluminium Handwheels With Handle Without Slot
PART NO D1 D2 D3 L1 L2 L3 NO OF REVOLVING APPROX WEIGHT
SPOKES MACHINE HANDLE KGS
MI - AL - REV - 80 - 10 - 0 80 10 24 16 84 29 3 M6 0.145
MI - AL - REV - 80 - 12 - 0 80 12 24 16 84 29 3 M6 0.145
MI - AL - REV - 100 - 10 - 0 100 10 26 17 86 30 3 M6 0.210
MI - AL - REV - 100 - 12 - 0 100 12 26 17 86 30 3 M6 0.210
MI - AL - REV - 125 - 12 - 0 125 12 28 18 100 36 3 M8 0.365
MI - AL - REV - 125 - 14 - 0 125 14 28 18 100 36 3 M8 0.365
MI - AL - REV - 160 - 14 - 0 160 14 39 20 120 40 3 M10 0.605
MI - AL - REV - 160 - 16 - 0 160 16 39 20 120 40 3 M10 0.605
MI - AL - REV - 200 - 18 - 0 200 18 40 24 124 45 3 M10 1.045
MI - AL - REV - 200 - 22 - 0 200 22 40 24 124 45 3 M10 1.045
MI - AL - REV - 250 - 22 - 0 250 22 50 28 146 51 5 M12 1.945
MI - AL - REV - 250 - 26 - 0 250 26 50 28 146 51 5 M12 1.945
38
ALUMINIUM HANDWHEELS
MI
Aluminium Handwheels Without Handle With Slot
MI - AL - 80 - 10 - 1 80 10 24 16 29 3 11.4 3 0.100
MI - AL - 80 - 12 - 1 80 12 24 16 29 4 13.8 3 0.100
MI - AL - 100 - 10 - 1 100 10 26 17 30 3 11.4 3 0.160
MI - AL - 100 - 12 - 1 100 12 26 17 30 4 13.8 3 0.160
MI - AL - 125 - 12 - 1 125 12 28 18 36 4 13.8 3 0.265
MI - AL - 125 - 14 - 1 125 14 28 18 36 5 16.3 3 0.265
MI - AL - 160 - 14 - 1 160 14 39 20 40 5 16.3 3 0.415
MI - AL - 160 - 16 - 1 160 16 39 20 40 5 18.3 3 0.415
MI - AL - 200 - 18 - 1 200 18 40 24 45 6 20.8 3 0.855
MI - AL - 200 - 22 - 1 200 22 40 24 45 6 24.8 3 0.855
MI - AL - 250 - 22 - 1 250 22 50 28 51 6 24.8 5 1.600
MI - AL - 250 - 26 - 1 250 26 50 28 51 8 29.3 5 1.600
MI - AL - 80 - 0 - 0 80 24 16 29 3 0.100
MI - AL - 100 - 0 - 0 100 26 17 30 3 0.160
MI - AL - 125 - 0 - 0 125 28 18 36 3 0.265
MI - AL - 160 - 0 - 0 160 39 20 40 3 0.415
MI - AL - 200 - 0 - 0 200 40 24 45 3 0.855
MI - AL - 250 - 0 - 0 250 50 28 51 5 1.600
39
CAST IRON HANDWHEELS
MI
L2
Material :
CAST IRON On Request :
Revolving Grips : 1. With Keyway Slot
Revolving Steel Handle
Revolving Aluminium Handle (Optional) 2. Different bore sizes
Thermo plastic handles (Optional)
Finish : 3. Hubs with Square Socket
Wheel Rim Turned & polished
4. Different Colour’s
MI - CI - 80 - 10 - 0 80 10 22 14 29 3 0.260
MI - CI - 80 - 12 - 0 80 12 22 14 29 3 0.260
MI - CI - 100 - 10 - 0 100 10 25 16 31 3 0.510
MI - CI - 100 - 12 - 0 100 12 25 16 31 3 0.510
MI - CI - 125 - 12 - 0 125 12 28 19 38 3 0.850
MI - CI - 125 - 14 - 0 125 14 28 19 38 3 0.850
MI - CI - 160 - 14 - 0 160 14 39 20 40 3 1.320
MI - CI - 160 - 16 - 0 160 16 39 20 40 3 1.320
MI - CI - 200 - 18- 0 200 18 40 24 46 3 2.470
MI - CI - 200 - 22- 0 200 22 40 24 46 3 2.470
MI - CI - 250 - 18- 0 250 22 50 28 51 5 4.220
MI - CI - 250 - 22- 0 250 26 50 28 51 5 4.220
40
CAST IRON HANDWHEELS
MI
Cast Iron Handwheels With Handle Without slot
PART NO D1 D2 D3 L1 L2 L3 NO OF REVOLVING APPROX WEIGHT
SPOKES MACHINE HANDLE KGS
MI - CI - REV - 80 - 10 - 0 80 10 22 14 84 29 3 M6 0.315
MI - CI - REV - 80 - 12 - 0 80 12 22 14 84 29 3 M6 0.315
41
CAST IRON HANDWHEELS
MI
Cast Iron Handwheels Without Handle With slot
MI - CI - 80 - 10 - 1 80 10 22 14 29 3 11.4 3 0.260
MI - CI - 80 - 12 - 1 80 12 22 14 29 4 13.8 3 0.260
MI - CI - 100 - 10 - 1 100 10 25 16 31 3 11.4 3 0.510
MI - CI - 100 - 12 - 1 100 12 25 16 31 4 13.8 3 0.510
MI - CI - 125 - 12 - 1 125 12 28 19 38 4 13.8 3 0.850
MI - CI - 125 - 14 - 1 125 14 28 19 38 5 16.3 3 0.850
MI - CI - 160 - 14 - 1 160 14 39 20 40 5 16.3 3 1.320
MI - CI - 160 - 16 - 1 160 16 39 20 40 5 18.3 3 1.320
MI - CI - 200 - 18 - 1 160 14 40 24 46 6 20.8 3 2.470
MI - CI - 200 - 22 - 1 160 16 40 24 46 6 24.8 3 2.470
MI - CI - 80 - 0 - 0 80 22 14 29 3 0.260
MI - CI - 100 - 0 - 0 100 25 16 31 3 0.510
42
MACHINE HANDLES
MI
Machine Handles Revolving
Steel & Aluminium
Material :
Handle & Axle part Steel
Finish :
Handle & Axle part galvanized Zinc Blue
Material :
Handle Aluminium & Axle part Steel
Finish :
Handle polished & Axle part galvanized Zinc Blue
PART NO PART NO D1 D3 D4 L1 L2 L3 SW
STEEL REVOLVING HANDLE ALUMINIUM REVOLVING HANDLE
MI - ST - REV - M6 - 50 MI - AL - REV - M6 - 50 16 M6 9 50 11 7 4
MI - ST - REV - M8 - 61 MI - AL - REV - M8 - 61 20 M8 13 61 13 7 4
MI - ST - REV - M10 - 75 MI - AL - REV - M10 - 75 25 M10 15 75 22 9 5
MI - ST - REV - M12 - 100 ----- 32 M12 20 100 22 12 6
PART NO D1 D3 D4 L1 L2 L3 SW
43
ABOUT MECHENGG INDUSTRIES
MECHENGG INDUSTRIES was established in the year 2016 ,
We offer wide range of manual Toggle Clamps and Handwheels ,
Our new product development is ongoing which is driven by our
customer demand to fill the needs that has not been met yet
OUR MISSION :
Is to offer more reliable high quality aesthetic
designed products by maintaining an international recognized
quality standards to our customers
OUR VISION :
To be more preferred & reliable brand trade mark
not only country wide but also worldwide .
BRAND QUALITY :
Our products has attained a high quality in production with more
reliable & economical , by having a expert technical and production team ,
Each products are designed and manufactured for safety , quality , and reliable ,
we ensure on time delivery & un paralleled customer service
MI - 02/2018-2019