Professional Documents
Culture Documents
CatalogRod Disogrin
CatalogRod Disogrin
Speed (ft/s): 3
Images Description
Image Image Description
Bull Dozer Manipulators
Fork Lift Buffer Seal
Tractor Valves
Stabiliser Shears
Hydraulic Presses Hydraulic Jacks
Mobile Arms Forging
General Cylinder Heavy Duty Construction
Injection Molding Heavy Duty Applications
Mobile Lifts Rolling Mills
Steel Mill Rotary Seal
Compression Molding Cranes
Marine Applications CNC Machines
DISOGRIN D-300 Rod Seal
DISOGRIN
♦ The D-300 Rod Seal provides superb sealing performance in standard and compact designs
♦ The D-Lock Edge provides axial stability thereby eliminating spiraling and tilting problems. This
secondary edge also serves as an additional barrier to dirt ingression.
♦ Superior abrasion and wear resistance of DISOGRIN 9250 urethane ensures a longer operating
life than other urethanes.
♦ Extrusion resistant material and design are engineered to withstand high pressures (6,000 psi)
and temperatures up to 300°F with intermittent use.
♦ Low compression set of DISOGRIN 9250 means cycle after tough cycle, the D-300 will continue to
seal against leakage.
Page D-300-2
DISOGRIN D-300 Rod Seal
Specification Sheet
Sealing Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Earthmoving Forklift Agriculture
Equipment Equipment
The DISOGRIN D-300 Rod Seal is typically an
injection molded part. However, for limited
quantities, prototypes or testing, it is also
available through our Merkel Freudenberg
SimQuick program. Please contact us for more
information.
Medium/Temperature D I S O G RI N D 9 2 S
Presses
Hydraulic Oil, HL, HLP -40°F to +230°F*
(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)
HFD Fluid --
Page D-300-3
DISOGRIN D-300 Rod Seal
Design Details
H L
Chamfered and burr-free, R2 <0.008"
20°
C D1 d D
+0.000
≥ 3" and < 7" - 0.004
d
The clearance gap, diameter D1, is based on ≥ 7" and < 10"
+0.000
- 0.005
the the system pressure. It is also based on
using non-metallic guide elements. ≥ 10" and < 15"
+0.000
- 0.006
+0.010
≥ 5" and < 7" - 0.000
D D1 d
Page D-300-5
DISOGRIN D-300 Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page D-300-6
DISOGRIN HBY Rod Buffer Seal
DISOGRIN
♦ The HBY Rod Buffer Seal is the newest in sealing technology for high performance cylinders.
♦ The HBY is designed specifically to serve as the primary seal in a sealing system.
♦ Superior abrasion and wear resistance of DISOGRIN 9250 ensures longer operating life than
other urethanes.
♦ Designed with a back-up ring, the HBY is engineered to withstand higher operating pressures
(spikes up to 8,000 psi) and temperatures than other seals.
♦ Low compression set of DISOGRIN 9250 means cycle after tough cycle, the HBY will continue to
seal against leakage.
♦ The patented static lip design, relieves any pressure build-up which may occur between the HBY
and the secondary seal (e.g. the D-300).
♦ The HBY is the most reliable protection of your sealing system for maximum service life.
♦ Available in a number of standard sizes, inch and metric, up to 10” (250mm) diameter.
Page HBY-2
DISOGRIN HBY Rod Buffer Seal
Specification Sheet
Sealing Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Earthmoving Cranes Agriculture
Equipment Equipment
Back-up Ring
Material Polyamide
Des ignation DISOGRIN 8408
Hardnes s 120 R Scale (Rockwell)
Medium/Temperature D I S O G RI N D 9 2 S
Presses
Hydraulic Oil, HL, HLP -40°F to +230°F*
(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)
HFD Fluid --
Page HBY-3
DISOGRIN HBY Rod Buffer Seal
Design Details
H L
Chamfered and burr-free, R2 <0.008"
R1 <0.016"
Chamfered and
burr-free
20°
C d D1 D
+0.000
≥ 3" and < 7" - 0.004
d
+0.000
The clearance gap, diameter D1, is based on ≥ 7" and < 10" - 0.005
the the system pressure. It is also based on +0.000
using non-metallic guide elements. ≥ 10" and < 15" - 0.006
+0.005
< 1.5"
Diameter D1 = d + Gmax - 0.000
+0.007
Pres s ure, ps i 1000 3000 5000 8000 ≥ 1.5" and < 2" - 0.000
+0.009
Lead-in Chamfer “C” D ≥ 3.25" and < 5" - 0.000
+0.010
≥ 5" and < 7" - 0.000
+0.011
Seal Cross-Section L ead-in Chamfer C ≥ 7" and < 9" - 0.000
D d D1
Page HBY-5
DISOGRIN RO Rod Seal
DISOGRIN
♦ The RO Rod Seal offers superb sealing performance as either a primary or secondary sealing
element.
♦ Superior abrasion and wear resistance of DISOGRIN 9250 ensures a longer operating life than
other urethanes.
♦ Extrusion resistant material and design are engineered to withstand high pressures (6,000 psi)
and high temperatures up to 300°F with intermittent use.
♦ Sealing lips are knife-cut to exert maximum sealing force and superior performance.
♦ The RO utilizes a preloaded lip design to ensure effective sealing at low pressures.
♦ Low compression set of DISOGRIN 9250 means cycle after tough cycle, the RO will continue to
seal against leakage.
♦ Resistant to pressure spikes and diesel effect for longer service life.
Page RO-2
DISOGRIN RO Rod Seal
Specification Sheet
Sealing Element
Material Polyurethane
Des ignation DISOGRIN D92S
Hardnes s 92 Shore A
Earthmoving Forklift Agriculture
Equipment Equipment
The DISOGRIN RO Rod Seal is typically an
injection molded part. However, for limited
quantities, prototypes or testing, it is also
available through our SimQuick program.
Please contact us for more information.
Medium/Temperature D I S O G RI N D 9 2 S
Presses
Hydraulic Oil, HL, HLP -40°F to +230°F*
(-40°C to +110°C) Installed Seal
HFA , HFB Fluids +41°F to +122°F
(+5°C to +50°C)
HFD Fluid --
Page RO-3
DISOGRIN RO Rod Seal
Design Details
H L
Chamfered and burr-free, R2 <0.008"
20°
C D1 d D
+0.000
≥ 3" and < 7" - 0.004
d
+0.000
The clearance gap, diameter D1, is based on ≥ 7" and < 10" - 0.005
the the system pressure. It is also based on +0.000
using non-metallic guide elements. ≥ 10" and < 15" - 0.006
+0.005
Diameter D1 = d + Gmax < 1.5" - 0.000
+0.007
Pres s ure, ps i 1000 3000 5000 6000 ≥ 1.5" and < 2" - 0.000
+0.009
Lead-in Chamfer “C” D ≥ 3.25" and < 5" - 0.000
+0.010
≥ 5" and < 7" - 0.000
+0.011
Seal Cross-Section L ead-in Chamfer C ≥ 7" and < 9" - 0.000
D D1 d
Page RO-5
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-6
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-7
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-8
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-9
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-10
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-11
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-12
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-13
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-14
DISOGRIN RO Rod Seal
Standard Range H L
Inch Sizes
D D1 d
Page RO-15
VERCO VCT Capped T-Seal
Major features
VERCO’s Capped T-Seal is a
are: Patented
double-acting, high-pres-
Anti-contamina-
sure, high performance
tion, Super extru-
piston seal accommodating
sion resistance,
larger extrusion gaps
Low wear, Long
when used in conjunction
life, and a Low
with VERCO Ultra-Precision
friction compact
Wear Rings.
stable design.
◆ Verco’s Patented anti-contamination seal will work in virtually any highly contaminated systems far
better than other seals of this type.
◆ The VERCO Capped T-Seal assembly consists of a filled PTFE cap, and an elastomeric energizer
that are protected from extrusion and contamination by our VERLON back-up rings.
◆ The VERCO Capped T-Seal is designed to handle temperature extremes, a wide variety of fluid
media and larger than normal clearances—yet it requires a short axial length gland, and as-
sembles and installs easily in the shop or in the field.
◆ Unlike conventional cap-type seals, VERCO’s Capped T-Seal virtually eliminates piston drift.
VERCO’s cap is loaded both in the static mode through high energizer squeeze, and in the
dynamic mode through the proportional axial-to-radial conversion of system pressure levels. Thus, a
fully positive seal is maintained throughout the pressure range. VERCO’s substantial, uniform cap
permits a high degree of evenly distributed radial load, virtually eliminating the possibility of
excessive wear and premature failure found in conventional cap type seals.
◆ Wider clearances can be used when designing with the Capped-T Seal. This allows for the use of
wear rings which eliminate the possibility of piston and bore damage due to metal-to-metal contact.
◆ When replacing single or multiple lip seals, a substantial reduction in piston length can be
achieved even with the addition of wear rings. This reduction does not come at the expense of
clearance limits or performance.
VERCO VCT Capped T-Seal
Specification Sheet
Materials
Sealing Element
Cap Rings:
Number Compound Temp. range Typical Service
0 PTFE 15% glass blue -100° to +450°F General purpose
1 PTFE 15% glass/5% moly -100° to +450°F General purpose hydraulic, hydrocarbon & water.
2 PTFE 25% carbon/graphite -100° to +450°F High pressure hydraulic, hydrocarbon & water. Low friction.
4 PTFE 40% bronze/5% moly -100° to +450°F High speed with improved sealability.
5 PTFE 55% bronze/5% moly -100° to +450°F High speed, pressure & abrasion resistance.
Energizer:
7 70 duro NBR -35° to +265°F General purpose hydraulic & hydrocarbon service.
8 80 duro NBR Low Temp. -65° to +240°F Low temperature hydraulic fluid service.
V Fluoroelastomer -20° to +400°F High temp.,harsh media applications, hydrocarbon & diester.
9 90 duro NBR -35° to +265°F General purpose hydraulic service.
Anti-Extrusion Rings:
2 PTFE PPS Filled -100° to +450°F Extended temperature & media resistance.
5 Acetal -40° to +225°F General purpose hydraulic, hydrocarbon service.
8 or 4 Glass Filled Nylon -40° to +300°F General purpose hydraulic service.
K PEEK Virgin -40° to +450°F Extended temperature, pressure & media resistance.
Temperature ranges shown are limited by the functional range of the VCT assembly. Materials shown may have
different operating ranges when used in other seal designs. The information contained herein is based on
laboratory tests believed to be reliable. It is offered for comparison and guidance to persons who will conduct their
own test in order to determine suitability for any purpose.
NOTE: VERCO Seal Co. has been a leader in designing seals for most hydraulic applications. Our engineering
department should be contacted for design criteria if your application exceeds the limits of the above materials
20°
.250 min.
.06 R MAX.
A
Earthmoving Forklift Agriculture F
Important Notes
Truck Injection Molding Std. Hydraulic
Crane Machines Cylinders
20°
.250 min.
.06 R MAX.
A F
32 RMS D/2
16 RMS
VCT - 024 - 7 - 0 - 8
Dash No. Loader Compound Cap Compound Back-up Compound
(See Table 1) (See page 3) (See page 3) (See page 3)
TABLE 1
Clearance (D)
BORE GLAND G w/o wear ring w/ wear ring
Dash No. A Tolerance F Tolerance (inch) max. min./max
20°
.250 min.
.06 R MAX.
A F
32 RMS D/2
16 RMS
VCT - 330 - 8 - 1 - 5
Dash No. Loader Compound Cap Compound Back-up Compound
(See Table 2) (See page 3) (See page 3) (See page 3)
TABLE 2
Clearance (D)
BORE GLAND G w/o wear ring w/ wear ring
Dash No. A Tolerance F Tolerance (inch) max. min./max
VCT - 4250 - 8 - 1 - 4
Dash No. Loader Compound Cap Compound Back-up Compound
(See Table 3) (See page 3) (See page 3) (See page 3)
TABLE 3
Clearance (D)
BORE GLAND G w/o wear ring w/ wear ring
Dash No. A Tolerance F Tolerance (inch) max. min./max
20°
.250 min.
.06 R MAX.
A F
32 RMS D/2
16 RMS
TABLE 3 (cont.)
Clearance (D)
BORE GLAND G w/o wear ring w/ wear ring
Dash No. A Tolerance F Tolerance (inch) max. min./max
1-800-527-5386
Distributed by:
VERCO Industrial Back-Ups
VERCO Series 1750 are the Standard POLY-TEMP™ O-Ring Back-ups. These
polyester elastomer (Hytrel* Formulation, HT2022**) back-ups will work on both I.D.
and O.D., static or dynamic applications. They can be continuously used at tempera-
tures from -60 degrees F to +275 degrees F. Interchangeable with AN6224,
AN6246, MS28774, MS28782, MS28783. Series 1750 Back-ups will make your
system last longer, period.
VERCO Series 1752 are the Leather Thickness POLY-TEMP™ O-Ring Back-ups.
These polyester elastomer (Hytrel* Formulation, HT2022**) back-ups will work on both
I.D. or O.D., static or dynamic applications. For use in glands per MIL-P-5514E and
MIL-5521. This series can also be used when a more severe application is encountered.
A slightly wider groove width is needed.
VERCO Series 1754 are the Contoured POLY-TEMP™ O-Ring Back-ups. These
polyester elastomer (Hytrel* Formulation, HT2022**) back-ups will work on both I.D.
and O.D., static or dynamic applications. They can be continuously used at temperatures
from -60 degrees F to +275 degrees F. Interchangeable with AN6224, AN6246,
MS28774, MS28782, MS28783. Series 1754 Back-ups will resist extrusion much
better than rubber ones, and are designed to fit in the groove. Last longer!
VERCO Industrial Back-Ups
Features & Benefits
Patent #4,674,754
Vented 1756 Series
VERCO Series 1756 are the “Vented” POLY-TEMP™ O-Ring Back-ups. These
polyester elastomer (Hytrel* Formulation, HT2022BLU**) back-ups are designed to work
primarily on O.D., dynamic applications. On some application there may be a pressure
trap between the O-Ring and Back-ups. This can cause a pressure lock. Series 1756
virtually eliminates these phenomena by “venting” the sealing system. Series 1756 can
be continuously used at temperatures from -60 degrees F to +275 degrees F.
VERCO Series 1758 are the NEW Standard in POLY-TEMP™ O-Ring Back-ups.
These polyester elastomer (Hytrel* Formulation, HT2022OR**) are specifically
designed for O.D., static applications. Series 1758 snap into the groove, will not
bunch up or twist. They can be continuously used at temperatures from -60 degrees
F. to +275 degrees F. Series 1758 Back-ups will make any system last longer,
period.
VERCO Series 9290 are the NEW Standard in POLY-TEMP™ 1/2 Thickness
O-Ring Back-ups. These polyester elastomer (Hytrel* Formulation, HT2022OR**)
are specifically designed for valve applications. Series 9290 will snap into the
groove, will not bunch up or twist. They can be continuously used at temperatures
from -60 degrees F. to +275 degrees F. 2 of Series 9290 Back-ups will fit into
a groove that was designed for an O-ring and 1 back-up, thus giving you a double
acting cavity.
VERCO Industrial Back-Ups
Features & Benefits
VERCO Series 9110 are VERLON back-up rings. When using Series 9110
behind a rubber or urethane u-cup, the life of the system will dramatically increase. If
you need higher pressures or greater side wall clearances, you need Series 9110.
Available in Verlon Formulation, VN9101*** or VN9500***. These series back-ups
will work on either I.D. or O.D. applications, in hydraulic or pneumatic systems. They
can be continuously used at temperatures from -60 degrees F to +300 degrees F.
Distributed by:
VERCO Poly-Hone Piston Seal
Poly-Hone® Piston Seals are directly inter-changeable with TFE, urethane, and rubber seals now
being used.
Verco Poly-Hone® Piston Seals are available in Series 1704 and Series 1708. The Series 1704
is a square cross section. This seal has a small footprint, making it resist hydroplaning, and is very
effective at low pressures.
Series 1708 is a rectangular cross section. This seal has a much larger footprint. It is designed for the
more demanding application. Series 1708 is able to withstand much higher shock loads. It’s rectan-
gular shape resists rolling or twisting making it more stable in the groove.
Poly-Hone® Piston Seals are directly inter-changeable with TFE, urethane, and rubber seals now
being used.
Verco Poly-Hone® Piston Seals are available in Series 1702 and Series 1710. The Series 1702
is a square cross section. This seal has a small footprint, making it resist hydroplaning, and is very
effective at low pressures.
Series 1710 is a rectangular cross section. This seal has a much larger footprint. It is designed for the
more demanding application. Series 1710 is able to withstand much higher shock loads. It’s rectan-
gular shape resists rolling or twisting making it more stable in the groove.
A
BORE DIA.
-008 .500 .241 .083 -009 -060 3.750 3.356 .130 -152
-010 .625 .366 .083 -011 -064 4.000 3.606 .130 -153
-012 .750 .491 .083 -013 -068 4.250 3.856 .130 -154
-014 .875 .616 .083 -015 -072 4.500 4.106 .130 -155
-016 1.000 .741 .083 -017 -076 4.750 4.356 .130 -156
-018 1.125 .866 .083 -019 -080 5.000 4.606 .130 -157
-020 1.250 .991 .083 -021 -084 5.250 4.856 .130 -158
-022 1.375 1.116 .083 -023 -088 5.500 5.106 .130 -159
-024 1.500 1.241 .083 -025 -092 5.750 5.232 .159 -251
-025 1.562 1.172 .122 -122 -096 6.000 5.482 .159 -253
-026 1.625 1.235 .122 -123 -100 6.250 5.732 .159 -255
-028 1.750 1.360 .122 -125 -104 6.500 5.982 .159 -257
-030 1.875 1.485 .122 -127 -108 6.750 6.232 .159 -258
-032 2.000 1.606 .130 -129 -112 7.000 6.482 .159 -259
-034 2.125 1.731 .130 -131 -116 7.250 6.732 .159 -260
-036 2.250 1.856 .130 -133 -120 7.500 6.982 .159 -261
-038 2.375 1.981 .130 -135 -124 7.750 7.232 .159 -262
-040 2.500 2.106 .130 -137 -128 8.000 7.482 .159 -263
-044 2.750 2.356 .130 -141 -136 8.500 7.982 .159 -265
-048 3.000 2.606 .130 -145 -144 9.000 8.482 .159 -267
-052 3.250 2.856 .130 -149 -152 9.500 8.982 .159 -269
-056 3.500 3.106 .130 -151 -160 10.000 9.482 .159 -271
A
BORE DIA.
-016 1.000 .688 .126 -115 -084 5.250 4.476 .378 -425
-020 1.250 .938 .126 -119 -088 5.500 4.726 .378 -427
-024 1.500 1.188 .126 -123 -092 5.750 4.976 .378 -429
-028 1.750 1.438 .126 -127 -096 6.000 5.226 .378 -431
-032 2.000 1.688 .126 -131 -104 6.500 5.726 .378 -435
-036 2.250 1.938 .126 -135 -112 7.000 6.226 .378 -438
-040 2.500 2.188 .126 -139 -120 7.500 6.726 .378 -440
-044 2.750 2.438 .126 -143 -128 8.000 7.226 .378 -442
-048 3.000 2.442 .279 -333 -136 8.500 7.726 .378 -444
-052 3.250 2.692 .279 -335 -144 9.000 8.110 .378 -445
-056 3.500 2.942 .279 -337 -152 9.500 8.610 .378 -446
-060 3.750 3.192 .279 -339 -160 10.000 9.110 .378 -447
-064 4.000 3.442 .279 -341 -176 11.000 10.110 .378 -449
-068 4.250 3.692 .279 -343 -192 12.000 11.110 .378 -451
-072 4.500 3.942 .279 -345 -208 13.000 12.110 .378 -453
-076 4.750 4.192 .279 -347 -224 14.000 13.110 .378 -455
-080 5.000 4.442 .279 -349
A
BORE DIA.
Series 1702 Heavy Duty POLY-HONE PISTON SEAL is designed to work in honed or super smooth
unhoned tubing. The 1702 series has been designed to withstand 5000 p.s.i. working pressure, -60o
F to 300o+ F running temperature and the hardware may have as much as .015 to .020” total side-
wall clearances. POLY-TEMP* HT2022MB is the standard compound used in this POLY-HONE.
-020 1.250 .750 .160 -210 -060 3.750 3.000 .250 -337
-024 1.500 1.000 .160 -214 -062 3.875 3.127 .250 -338
-026 1.625 1.125 .160 -216 -064 4.000 3.250 .250 -339
-028 1.750 1.250 .160 -218 -068 4.250 3.500 .250 -341
-030 1.875 1.375 .160 -220 -072 4.500 3.750 .250 -343
-032 2.000 1.500 .160 -222 -076 4.750 4.000 .250 -345
-036 2.250 1.500 .250 -325 -080 5.000 4.250 .250 -347
-040 2.500 1.750 .250 -327 -084 5.250 4.500 .250 -349
-044 2.750 2.000 .250 -329 -088 5.500 4.750 .250 -351
-048 3.000 2.250 .250 -331 -092 5.750 5.000 .250 -353
-052 3.250 2.500 .250 -333 -096 6.000 5.250 .250 -355
-056 3.500 2.750 .250 -335 -104 6.500 5.750 .250 -359
A
BORE DIA.
Series 1710 POLY-HONE PISTON SEALS are designed to work at pressures of 5000 p.s.i. with
side-wall clearances as great as .020”. This series is also interchangeable with TFE slipper seals with
a rectangular cross-section now in use, but POLY-HONES will not cold-flow and are easy to install.
POLY-TEMP* HT2022MB is used in manufacture.
-016 1.000 .633 .170 -208 -056 3.500 2.880 .250 -336
-018 1.125 .758 .170 -210 -060 3.750 3.130 .250 -338
-020 1.250 .883 .170 -212 -064 4.000 3.380 .250 -340
-022 1.375 1.008 .170 -214 -068 4.250 3.630 .250 -342
-024 1.500 1.133 .170 -216 -072 4.500 3.880 .250 -344
-026 1.625 1.258 .170 -218 -076 4.750 4.130 .250 -346
-028 1.750 1.383 .170 -220 -080 5.000 4.380 .250 -348
-030 1.875 1.508 .170 -222 -084 5.250 4.500 .310 -425
-032 2.000 1.500 .250 -325 -088 5.500 4.750 .310 -427
-034 2.125 1.630 .250 -326 -092 5.750 5.000 .310 -429
-036 2.250 1.775 .250 -327 -096 6.000 5.250 .310 -431
-038 2.375 1.880 .250 -328 -100 6.250 5.500 .310 -433
-040 2.500 2.000 .250 -329 -104 6.500 5.750 .310 -435
-044 2.750 2.130 .250 -330 -108 6.750 6.000 .310 -437
-048 3.000 2.380 .250 -332 -112 7.000 6.250 .310 -438
-052 3.250 2.630 .250 -334
1-800-527-5386
Distributed by:
VERCO Poly-Temp Static Back-Ups
Maximum Extrusion
Resistance
Easy to Install
Avoids Twisting or
Bunching
◆ VERCO SERIES 1758 have been designed specifically to fit into a static O-Ring groove. The
Back-Up cross section has been engineered to not only fit, but give you optimum life. See table on
following page for actual back-up cross section.
◆ Series 1758 Back-Ups fit snugly into the groove. This helps avoid twisting or bunching of the
back-up ring. Series 1758 Back-Ups are manufactured from compound HT20220R. This is a
polyester material compounded from DuPont Hytrel®. It has extremely good extrusion resistance.
Tests have shown that compound POLY-TEMP HT2022OR can last as much as 5 times longer
than urethane or rubber back-ups.
◆ Series 1758 Poly-Temp Back-Ups can be easily stretched into placed without taking a
permanent set. This quality makes assembly easy, requiring less time than other types of back-ups
and will not twist, fall out or roll over in the groove.
◆ Half-thickness back-ups in this series are also available. Ask for Series 1790.
VERCO Poly-Temp Static Back-Ups
Design Details
0º TO 5º BREAK CORNERS
(TYP.) APPROX. .005 RAD.
1/2 E
W W
32 .005
MAX.
W
R
63
I.D. W
F L
63
.003 MAX.
32
GLAND DETAIL
PRESSURE PRESSURE PRESSURE
G G G
ONE TWO
BACK-UP BACK-UP
RING RINGS
(a) Clearance gap must be held to a minimum consistent with design requirements for temperature range variation.
(b) Total Indicator reading between groove and adjacent bearing surface.
(c) Reduce maximum diametral clearance 50% when using silicone O-rings.
VERCO Poly-Temp Static Back-Ups
Actual Part Dimensions
SERIES 1758
T VERCO P/N I.D. C/S Width
A Tol. W. Tol. T. Tol.
Important Notes
Truck Injection Molding Std. Hydraulic
Crane Machines Cylinders
Distributed by: