Professional Documents
Culture Documents
Non-Isolated Buck APFC LED Driver Description Features
Non-Isolated Buck APFC LED Driver Description Features
Non-Isolated Buck APFC LED Driver Description Features
Description Features
The BP2338J is a high precision non-isolated buck Fast start up and power supply with HV JFET
driver with active PFC, specially designed for universal Integrated with 600V Power MOSFET
input offline constant current LED lighting. The driver Active PFC for High Power Factor and Low THD
with on-chip PFC circuit achieves high power factor System Efficiency up to 95%
and low THD. Operating in critical conduction mode, ±3% LED Output Current Accuracy
the power MOSFET switching loss is reduced and the Excellent Line and Load Regulation
inductor is fully utilized. Critical Conduction Mode Operation
Ultra Low (300uA) Operating Current
The BP2338J integrates a 600V power MOSFET.
LED Short/Open Protection
With few external components, the LED output
Current Sensing Resistor Open Protection
current can be precisely controlled.
Cycle by Cycle Current Limit
The BP2338J utilizes patented floating ground VCC Under Voltage Protection
structure. The inductor current is sensed during the Auto Fault Recovery
whole switching cycle. So it achieves high precision Thermal Regulation Function
output current control, and excellent line regulation and
load regulation.
Applications
LED retrofit lamps, Bulb, Spot Light, GU10/E27
The BP2338J utilizes patented start up technology
LED PAR30, PAR38 Lamp
with HV JFET. So it achieves fast start up, reduce
LED tube, LED String
count of external components, and realize smaller
Other LED Lighting
form factor.
Typical Application
BP2338J
5 DRAIN FB 4
6 DRAIN CS 8
3 VCC CS 7
1 COMP GND 2
AC
Ordering Information
COMP CS
XXXXXY: Lot Code
GND CS W: Sign
XXXXXY
BP2338
WXYYJ
X: Year
VCC DRAIN
YY: Week
FB DRAIN
Pin Definition
Pin No. Name Description
Loop Compensation Node. This pin connects a capacitor to GND for
1 COMP stabilization of the control loop, achieving accurate LED current, high
Power Factor and low THD.
2 GND Ground.
3 VCC Power Supply Pin. Connect a bypass capacitor from this pin to GND.
Feedback Voltage detection Pin. This pin detects the inductor
4 FB
demagnetization signal and the output voltage.
5,6 DRAIN Internal HV Power MOSFET Drain.
Current Sense Pin. Connect a resistor to GND to sense the inductor
7,8 CS
current.
ESD (note3) 2 KV
Note 1: Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. Under “recommended operating
conditions” the device operation is assured, but some particular parameter may not be achieved. The electrical characteristics table defines the operation
range of the device, the electrical characteristics is assured on DC and AC voltage by test program. For the parameters without minimum and maximum value
in the EC table, the typical value defines the operation range, the accuracy is not guaranteed by spec.
Note 2: The maximum power dissipation decrease if temperature rise, it is decided by TJMAX, θJA, and environment temperature (TA). The maximum power
dissipation is the lower one between PDMAX = (TJMAX - TA)/ θJA and the number listed in the maximum table.
Feedback Section
FB Falling Edge
VFB_FALL FB Falling 0.2 V
Threshold Voltage
VFB_HYS FB Hysteresis Voltage FB Rising 0.15 V
FB Over Voltage
VFB_OVP 1.6 V
Protection Threshold
TON_MAX Maximum On Time 35 us
Compensation Section
Note 5: the maximum and minimum parameters specified are guaranteed by test, the typical value are guaranteed by design, characterization and statistical
analysis
UVLO
Thermal &VREF
Regulation
5,6 DRAIN
Current
- 7,8 CS
COMP 1 Gm Sense
+ VREF
Demag 4 FB
Application Information
The BP2338J integrating a 600V power MOSFET, is by the output voltage through a diode.
a high precision non-isolated buck APFC LED driver,
2 Constant Current Control
specially designed for universal mains with constant
current control. The driver with on-chip PFC circuit The BP2338J utilizes patent pending floating ground
achieves high power factor, low THD and high structure. The inductor current is sensed during the
efficiency. whole switching cycle, thus it achieves high precision
output current control and also excellent line and load
1 Start Up
regulation.
After system powered on, the capacitor on VCC pin is
The LED current can be calculated by the equation:
charged up by the startup resistor. When the VCC pin
voltage reaches the turn on threshold, the internal
VREF
circuits start working. The COMP pin voltage is I OUT
pulled up to 1.5V quickly, then the system starts
Rcs
switching from 10kHz frequency at the beginning, the Where,
COMP voltage rises up gradually, and the inductor VREF: Internal reference voltage
peak current also rises up. The LED current hence Rcs: Value of the current sensing resistor
achieves a soft start without overshoot. After the
output voltage is built up, the VCC power is supplied
BP2338J_EN _DS_Rev.1.0 www.bpsemi.com 7
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP2338J
Non-isolated Buck APFC LED Driver
3 Feedback Network voltage will decrease until it reaches UVLO threshold.
Then the system will re-start again. If the fault
The BP2338J senses the zero current crossing
condition is removed, the system will resume normal
information through the feedback network, the FB
operation.
falling threshold voltage is set to 0.2V with 0.15V
hysteresis. The FB pin is multiple used to detect When the output is short circuit or the inductor is
output voltage, the OVP threshold voltage is 1.6V. saturated, the CS peak voltage will be relatively high.
The ratio of FB upper resistor to lower resistor can be When CS voltage reaches the internal limitation
set as: (1.5V), the power MOSFET will be turned off
instantaneously. This cycle by cycle current limitation
RFBL 1.6V can help protecting the power MOSFET, the inductor
RFBL RFBH VOVP and the output diode.
Physical Dimensions