Professional Documents
Culture Documents
6na - Data - Flypartsguy - Com - 1.2018
6na - Data - Flypartsguy - Com - 1.2018
www.FlyPartsGuy.com
Weichai America Corp.
Units Specificaiton
Std Metric 1500 2200
Basic Data
Type N/A In-Line 4 cycle
Number of cylinders N/A 6
Aspiration N/A Turbo Charge Air Cooled
Bore in mm 4.1 105 4.1 105
Stroke in mm 5.1 130 5.1 130
Displacement in^3 L 411.9 6.75 411.9 6.75
Lambda N/A 1.0
Compression Ratio N/A 9.75
Mean Piston Speed ft/min m/s 1535.4 7.8 1535.4 7.8
Rotation Viewed from Flywheel N/A Counter Clockwise
Firing Order N/A 1-5-3-6-2-4
Gross Prime Power Rating1,2,3 Per ISO 3046 at the Flywheel
NG HP kW 91.3 68.1 121.4 90.5
LP HP kW 96.3 71.8 102.2 76.2
MEP (@ rated Load on NG) psi bar 55.6 8.1 174.2 7.3
MEP (@ rated Load on LP) psi bar 58.7 8.5 143.7 6.2
Thermal Balance
Total Fuel Ft3/hr kg/hr 758.1 15.4 1068.2 21.7
Heat to Work btu/min kW 3753.4 66 5004.5 88
Heat rejected to Cooling water at rated Load btu/min kW 3383.7 59.5 4504.0 79.2
Heat Rejection per CAC btu/min kW -- -- -- --
Heat Rejected to Exhaust (LHV TO 77oF) btu/min kW 3270.0 57.5 4356.2 76.6
Engine Radiated Heat btu/min kW 511.8 9 682.4 12
Weight and Power Output
Dry Weight
Fan to Flywheel lb kg 1266.5 575 1266.5 575
Rad to Flywheel lb kg 1541.9 700 1541.9 700
Wet Weight
Fan to Flywheel lb kg 1284.1 583 1284.1 583
Rad to Flywheel lb kg 1603.5 728 1603.5 728
Maximum Allowable Bending Moment at Rear of Block lb ft Nm 5457.5 7400 5457.5 7400
Moment of Inertia About Roll Axis lb ft^2 kg m^2 17.7 3.6 17.7 3.6
Flywheel housing N/A SAE No.3 SAE No.3
Flywheel N/A No.10 No.10
Number of Flywheel Teeth N/A 145 145
Exhaust System
Type Air Cooled Manifold
Maximum allowable Back pressure inH2O kPa 68.3 17 68.3 17
Standard Catalyst Back pressure inH2O kPa 40.2 10 40.2 10
Exhaust Outlet Pipe Size (Turbo outlet to catalyst inlet) in mm 3.37→2.3577.5→59.7 3.37→2.35 77.5→59.7
Maximum Turbine Inlet Temperature ℉ ℃ -- -- -- --
Exhaust Flow at Rated Power lb/hr kg/hr 599.1 272 837.0 380
Air Induction System
Maximum allowable Intake Air Restriction with Air Cleaner
Clean inH2O kPa 8.0 2.0 8.0 2.0
Dirty inH2O kPa 14.9 3.7 14.9 3.7
Combustion Air required (entire engine) lb/hr kg/hr 565.0 256.5 788.5 358
Combustion Air required (entire engine) CFM m^3/min 117.0 3.3 163.3 4.6
Charge Air Cooler
Compressor Outlet Temperature ℉ ℃ -- -- -- --
Compressor Flow Rate per CAC lb/hr kg/hr -- -- -- --
CAC Rise over Ambient (Charge)
Specified ℉ ℃ -- -- -- --
Acutal ℉ ℃ -- -- -- --
Max pressure loss across the CAC inH2O kPa -- -- -- --
Maximum Intake Air Temperature (IAT) ℉ ℃ 131.0 55.0 131.0 55
ECU IAT Warning ℉ ℃ 169.9 76.6 169.9 76.6
ECU IAT Shutdown ℉ ℃ 180.0 82.2 180.0 82.2
Units Specificaiton
Std Metric 1500 2200
Cooling System
Coolant Capacity
Engine only gal L 2.1 8 2.1 8
Engine with Radiator gal L 4.2 16 4.2 16
Engine Coolant Flow gal/min L/min 54.2 205 54.2 205
Water Pump Speed RPM 1860 2728
Standard Thermostat Range
Cracking Temperature ℉ ℃ 167.0 75 167.0 75
Full Open Temperature ℉ ℃ 194.0 90 194.0 90
Maximum Allowable Pressure Cap psi bar 13.2 0.9 13.2 0.9
Ambient Clearance Open Genset (water) (Air-to-Boil)
Specified ℉ ℃ ≥107 ≥42 ≥107 ≥42
Acutal ℉ ℃ 122.7 50.4 125.4 51.9
Maximum Allowable Top Tank Temperature ℉ ℃ 203.0 95 203.0 95
ECU Warning ℉ ℃ 205.0 96 205.0 96
ECU Shutdown ℉ ℃ 212.0 100 212.0 100
Fan Power HP kW 3.4 2.5 10.1 7.5
Fan Diameter, including blades in mm 24.4 620 24.4 620
Fan Speed RPM 1860 2728
Electrical System
Minimum Recommended Battery Capacity AH 150 150
Cold Cranking Current
Engine only CCA 750 750
Engine with Drive train CCA 750 750
Maximum Allowable Resistance of Starting Circuit Ohms 0.002 0.002
Starting Motor Power HP kW 5.4 4 5.4 4
Battery Charging Alternator
Voltage Volts 14 14
Current Amps 90 90
Coil primary Resistance Ohms 0.59Ω ± 10% 0.59Ω ± 10%
Spark Plug p/n TORCH/R 5498-3 TORCH/R 5498-3
Spark plug gap mm 0.3-0.35 0.3-0.35
Lubrication System SAE 15W-40 Low Ash Gas engine oil (.25-.5% by wt), API CD/CF or
Oil Specification higher
Oil Pressure
Idle
Min Psi Bar 11.8 0.8 11.8 0.8
Max Psi Bar 17.6 1.2 17.6 1.2
Rated Speed
Min Psi Bar 44.1 3 44.1 3
Max Psi Bar 97.0 6.6 97.0 6.6
Maximum Allowable Oil Temperature ℉ ℃ 239.0 115 239.0 115
Engine Oil Capacity
Min Qts L 14.8 14 14.8 14
Max Qts L 28.5 27 28.5 27
Oil Filter Capacity Qts L 2.1 2 2.1 2
ECU Oil Pressure Warning psi kPa 10 70 10 70
ECU Oil Pressure Shut Down psi kPa 7 49 7 49
Fuel System
Fuel Consumption
NG Ft3/hr kg/hr 758.1 15.4 1068.2 21.7
LP Ft3/hr kg/hr 836.8 17.0 984.5 20.0
Maximum EPR Rated Pressure psi kPa 1.0 6.9 1.0 6.9
Maximum Running pressure to EPR inH2O kPa 10.8 2.7 10.8 2.7
Minimum Running pressure to EPR inH2O kPa 6.8 1.7 6.8 1.7
Minimum Gas Supply Pipe Size 1-1/4" NPT
Maximum EPR Rated Pressure psi kPa 1.0 6.90 1.0 6.90
Maximum Running Pressure to EPR inH2O kPa 10.8 2.70 10.8 2.70
Minimum Running Pressure to EPR inH2O kPa 6.8 1.70 6.8 1.70
Minimum LPG Supply Pipe Size4 1/4" NPT
Units Specificaiton
Std Metric 1500 2200
70
Power (kW)
300
65
275
60
250
225 55
200 50
175 45
150 40
1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200
Speed (rpm)
240 30
TotalFuel(m^3/h)
230 25
BSFC (g/kW.h)
220 20
210 15
200 10
1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200
Speed (rpm)
475 82
450 76
Torque (N.m)
425 70
Power (kW)
400 64
375 58
350 52
325 46
300 40
1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200
Speed (rpm)
Units Specificaiton
Std Metric 1500 2200
Fuel Consumption Curve vs. Speed (Liquid Propane Gas)
270 12
260 11
250 10
TotalFuel(gallom/h)
240 9
BSFC (g/kW.h)
230 8
220 7
210 6
200 5
1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200
Speed (rpm)
1
Standby and overload ratings based on ISO3046.
2
All ratings are gross flywheel horsepower corrected to 77oF at an altitude of 328 feet with no cooling fan or alternator losses using heating value for NG of
1025 BTU/SCF (HHV) and for propane of 2490 BTU/SCF (HHV).
3
Production tolerances in engines and installed components can account for power variations of +/- 5%. Altitude, temperature and excessive exhaust and intake
restrictions should be applied to power calculations. Engine maybe operated at : up to 1200 feet and 86°F without power deration. For sustained operation
above these conditions, derate by 2.5% per 1000 feet, and 1.5% per 10°F.
4
The preceeding pipe sizes are only suggestions and piping sizes may vary with temperature, pressure, distance from supply and application of local codes. Gas
must be available at adequate volume and pressure for engine at the EPR.
Units Specificaiton
Std Metric 1500 1800
Basic Data
Type N/A In-Line 4 cycle
Number of cylinders N/A 6
Aspiration N/A Naturally Aspirated
Bore in mm 4.1 105 4.1 105
Stroke in mm 5.1 130 5.1 130
Displacement in^3 L 411.9 6.75 411.9 6.75
Lambda N/A 1.0
Compression Ratio N/A 9.75
Mean Piston Speed ft/min m/s 1535.4 7.8 1535.4 7.8
Rotation Viewed from Flywheel N/A Counter Clockwise
Firing Order N/A 1-5-3-6-2-4
1,2,3
Gross Standby Power Rating Per ISO 3046 at the Flywheel
NG HP kW 88.5 66.0 111.3 83.0
LP HP kW 96.6 72.0 119.3 89.0
MEP (@ rated Load on NG) psi bar 53.9 7.8 56.5 8.2
MEP (@ rated Load on LP) psi bar 58.8 8.5 60.6 8.8
Thermal Balance
Total Fuel Ft3/hr kg/hr 758.1 15.4 900.8 18.3
Heat to Work btu/min kW 3753.4 66 4549.5 80
Heat rejected to Cooling water at rated Load btu/min kW 3383.7 59.5 4111.6 72.3
Heat Rejection per CAC btu/min kW -- -- -- --
Exhaust Heat (LHV TO 77oF) btu/min kW 3270.0 57.5 3980.8 70
Enigne Radiated Heat btu/min kW 511.8 9 597.1 10.5
Gross Prime Power Rating1,2,3 Per ISO 3046 at the Flywheel
NG HP kW 88.5 66.0 107.3 80.0
LP HP kW 96.6 72.0 118.0 88.0
MEP (@ rated Load on NG) psi bar 53.9 7.8 174.2 7.9
MEP (@ rated Load on LP) psi bar 58.8 8.5 143.7 8.7
Thermal Balance
Total Fuel Ft3/hr kg/hr 758.1 15.4 900.8 18.3
Heat to Work btu/min kW 3753.4 66 4549.5 80
Heat rejected to Cooling water at rated Load btu/min kW 3383.7 59.5 4111.6 72.3
Heat Rejection per CAC btu/min kW -- -- -- --
Exhaust Heat (LHV TO 77oF) btu/min kW 3270.0 57.5 3980.8 70
Engine Radiated Heat btu/min kW 511.8 9 597.1 10.5
Weight and Power Output
Dry Weight
Fan to Flywheel lb kg 1266.5 575 1266.5 575
Rad to Flywheel lb kg 1541.9 700 1541.9 700
Wet Weight
Fan to Flywheel lb kg 1284.1 583 1284.1 583
Rad to Flywheel lb kg 1603.5 728 1603.5 728
Maximum Allowable Bending Moment at Rear of Block lb ft Nm 5457.5 7400 5457.5 7400
Moment of Inertia About Roll Axis lb ft^2 kg m^2 17.7 3.62 17.7 3.62
Flywheel housing N/A SAE No.3 SAE No.3
Flywheel N/A No.10 No.10
Number of Flywheel Teeth N/A 145 145
Exhaust System
Type Air Cooled Manifold
Maximum allowable Back pressure inH2O kPa 68.3 17 68.3 17
Standard Catalyst Back pressure inH2O kPa 40.2 10 40.2 10
Exhaust Outlet Pipe Size (Turbo outlet to catalyst inlet) in mm 3.37→2.35 77.5→59.7 3.37→2.35 77.5→59.7
Maximum Turbine Inlet Temperature ℉ ℃ -- -- -- --
Exhaust Flow at Rated Power lb/hr kg/hr 599.1 272 710.1 322
Air Induction System
Maximum allowable Intake Air Restriction with Air Cleaner
Clean inH2O kPa 8.0 2.0 8.0 2.0
Dirty inH2O kPa 14.9 3.7 14.9 3.7
Units Specificaiton
Std Metric 1500 1800
Combustion Air required (entire engine) lb/hr kg/hr 565.0 256.5 668.9 303.7
Combustion Air required (entire engine) CFM m^3/min 117.0 3.3 236.7 6.7
Charge Air Cooler
Compressor Outlet Temperature ℉ ℃ -- -- -- --
Compressor Flow Rate per CAC lb/hr kg/hr -- -- -- --
CAC Rise over Ambient (Charge)
Specified ℉ ℃ -- -- -- --
Acutal ℉ ℃ -- -- -- --
Max pressure loss across the CAC inH2O kPa -- -- -- --
Maximum Intake Air Temperature (IAT) ℉ ℃ 180.0 82.2 180.0 82.2
ECU IAT Warning ℉ ℃ 169.9 76.6 169.9 76.6
ECU IAT Shutdown ℉ ℃ 180.0 82.2 180.0 82.2
Cooling System
Coolant Capacity
Engine only gal L 2.1 8 2.1 8
Engine with Radiator gal L 4.2 16 4.2 16
Engine Coolant Flow gal/min L/min 54.2 205 54.2 205
Water Pump Speed RPM 1860 2232
Standard Thermostat Range
Cracking Temperature ℉ ℃ 167.0 75 167.0 75
Full Open Temperature ℉ ℃ 194.0 90 194.0 90
Maximum Allowable Pressure Cap psi bar 13.2 0.9 13.2 0.9
Ambient Clearance Open Genset (water) (Air-to-Boil)
Specified ℉ ℃ ≥107 ≥42 ≥107 ≥42
Acutal ℉ ℃ 122.7 50.4 125.8 52.1
Maximum Allowable Top Tank Temperature ℉ ℃ 214.9 101.6 214.9 101.6
ECU Warning ℉ ℃ 204.8 96.0 204.8 96.0
ECU Shutdown ℉ ℃ 214.9 101.6 214.9 101.6
Fan Power HP kW 3.4 2.5 5.4 4.0
Fan Diameter, including blades in mm 24.4 620 24.4 620
Fan Speed RPM 1860 2232
Electrical System
Minimum Recommended Battery Capacity AH 150 150
Cold Cranking Current
Engine only CCA 750 750
Engine with Drive train CCA 750 750
Maximum Allowable Resistance of Starting Circuit Ohms 0.002 0.002
Starting Motor Power HP kW 5.4 4 5.4 4
Battery Charging Alternator
Voltage Volts 14 14
Current Amps 90 90
Coil primary Resistance Ohms 0.59Ω ± 10% 0.59Ω ± 10%
Spark Plug p/n TORCH/R 5498-3 TORCH/R 5498-3
Spark plug gap mm 0.3-0.35 0.3-0.35
Lubrication System
SAE 15W-40 Low Ash Gas engine oil (.25-.5% by wt), API CD/CF or higher;
Oil Specification Please refer Manual Book for different situation.
Oil Pressure
Idle
Min Psi Bar 11.8 0.8 11.8 0.8
Max Psi Bar 17.6 1.2 17.6 1.2
Rated Speed
Min Psi Bar 44.1 3 44.1 3
Max Psi Bar 97.0 6.6 97.0 6.6
Maximum Allowable Oil Temperature ℉ ℃ 239.0 115 239.0 115
Engine Oil Capacity
Min Qts L 14.8 14 14.8 14
Max Qts L 28.5 27 28.5 27
Oil Filter Capacity Qts L 2.1 2 2.1 2
ECU Oil Pressure Warning psi kPa 10 70 10 70
Units Specificaiton
Std Metric 1500 1800
ECU Oil Pressure Shut Down psi kPa 7 49 7 49
Fuel System
Fuel Consumption
3
NG Ft /hr kg/hr 758.1 15.4 900.8 18.3
3
LP Ft /hr kg/hr 836.8 17.0 994.4 20.2
Maximum EPR Rated Pressure psi kPa 1.0 6.9 1.0 6.9
Maximum Running pressure toEPR inH2O kPa 10.8 2.7 10.8 2.7
Minimum Running pressure to EPR inH2O kPa 6.8 1.7 6.8 1.7
Minimum Gas Supply Pipe Size 1-1/4" NPT
Maximum EPR Rated Pressure psi kPa 1.0 6.90 1.0 6.90
Maximum Running Pressure to EPR inH2O kPa 10.8 2.70 10.8 2.70
Minimum Running Pressure to EPR inH2O kPa 6.8 1.70 6.8 1.70
Minimum LPG Supply Pipe Size4 1/4" NPT
700 47
600 41
500 35
Total Fuel(m³/h)
BSFC(g/kW.h)
400 29
300 23
200 17
100 11
0 5
6 16 26 36 46 56 66
Power (kW)
700 16
600 14
500 12
Total Fuel(galloon/h)
BSFC(g/kW.h)
400 10
300 8
200 6
100 4
0 2
7 17 27 37 47 57 67 77
Power (kW)
Units Specificaiton
Std Metric 1500 1800
Fuel Consumption Curve @ 1800 RPM (Natural Gas)
700 47
600 41
500 35
Total Fuel(m³/h)
BSFC(g/kW.h)
400 29
300 23
200 17
100 11
0 5
8 17 26 35 44 53 62 71 80
Power (kW)
600 14
500 12
BSFC(g/kW.h)
300 8
200 6
100 4
0 2
8 18 28 38 48 58 68 78 88
Power (kW)
1
Standby and overload ratings based on ISO3046.
2
All ratings are gross flywheel horsepower corrected to 77oF at an altitude of 328 feet with no cooling fan or alternator losses using heating value for NG of 1025
BTU/SCF (HHV) and for propane of 2490 BTU/SCF (HHV).
3
Production tolerances in engines and installed components can account for power variations of +/- 5%. Altitude, temperature and excessive exhaust and intake
restrictions should be applied to power calculations. Engine maybe operated at : up to 1200 feet and 86°F without power deration. For sustained operation above these
conditions, derate by 2.5% per 1000 feet, and 1.5% per 10°F.
4
The preceeding pipe sizes are only suggestions and piping sizes may vary with temperature, pressure, distance from supply and application of local codes. Gas must
be available at adequate volume and pressure for engine at the EPR.
Units Specificaiton
Std Metric 1500 1800
Basic Data
Type N/A In-Line 4 cycle
Number of cylinders N/A 6
Aspiration N/A Naturally Aspirated
Bore in mm 4.1 105 4.1 105
Stroke in mm 5.1 130 5.1 130
Displacement in^3 L 411.9 6.75 411.9 6.75
Lambda N/A 1.0
Compression Ratio N/A 9.75
Mean Piston Speed ft/min m/s 1535.4 7.8 1535.4 7.8
Rotation Viewed from Flywheel N/A Counter Clockwise
Firing Order N/A 1-5-3-6-2-4
1,2,3
Gross Standby Power Rating Per ISO 3046 at the Flywheel
NG HP kW 88.5 66.0 111.3 83.0
LP HP kW 96.6 72.0 119.3 89.0
MEP (@ rated Load on NG) psi bar 53.9 7.8 56.5 8.2
MEP (@ rated Load on LP) psi bar 58.8 8.5 60.6 8.8
Thermal Balance
Total Fuel Ft3/hr kg/hr 758.1 15.4 900.8 18.3
Heat to Work btu/min kW 3753.4 66 4549.5 80
Heat rejected to Cooling water at rated Load btu/min kW 3383.7 59.5 4111.6 72.3
Heat Rejection per CAC btu/min kW -- -- -- --
Exhaust Heat (LHV TO 77oF) btu/min kW 3270.0 57.5 3980.8 70
Enigne Radiated Heat btu/min kW 511.8 9 597.1 10.5
Gross Prime Power Rating1,2,3 Per ISO 3046 at the Flywheel
NG HP kW 88.5 66.0 107.3 80.0
LP HP kW 96.6 72.0 118.0 88.0
MEP (@ rated Load on NG) psi bar 53.9 7.8 174.2 7.9
MEP (@ rated Load on LP) psi bar 58.8 8.5 143.7 8.7
Thermal Balance
Total Fuel Ft3/hr kg/hr 758.1 15.4 900.8 18.3
Heat to Work btu/min kW 3753.4 66 4549.5 80
Heat rejected to Cooling water at rated Load btu/min kW 3383.7 59.5 4111.6 72.3
Heat Rejection per CAC btu/min kW -- -- -- --
Exhaust Heat (LHV TO 77oF) btu/min kW 3270.0 57.5 3980.8 70
Engine Radiated Heat btu/min kW 511.8 9 597.1 10.5
Weight and Power Output
Dry Weight
Fan to Flywheel lb kg 1266.5 575 1266.5 575
Rad to Flywheel lb kg 1541.9 700 1541.9 700
Wet Weight
Fan to Flywheel lb kg 1284.1 583 1284.1 583
Rad to Flywheel lb kg 1603.5 728 1603.5 728
Maximum Allowable Bending Moment at Rear of Block lb ft Nm 5457.5 7400 5457.5 7400
Moment of Inertia About Roll Axis lb ft^2 kg m^2 17.7 3.62 17.7 3.62
Flywheel housing N/A SAE No.3 SAE No.3
Flywheel N/A No.10 No.10
Number of Flywheel Teeth N/A 145 145
Exhaust System
Type Air Cooled Manifold
Maximum allowable Back pressure inH2O kPa 68.3 17 68.3 17
Standard Catalyst Back pressure inH2O kPa 40.2 10 40.2 10
Exhaust Outlet Pipe Size (Turbo outlet to catalyst inlet) in mm 3.37→2.35 77.5→59.7 3.37→2.35 77.5→59.7
Maximum Turbine Inlet Temperature ℉ ℃ -- -- -- --
Exhaust Flow at Rated Power lb/hr kg/hr 599.1 272 710.1 322
Air Induction System
Maximum allowable Intake Air Restriction with Air Cleaner
Clean inH2O kPa 8.0 2.0 8.0 2.0
Dirty inH2O kPa 14.9 3.7 14.9 3.7
Units Specificaiton
Std Metric 1500 1800
Combustion Air required (entire engine) lb/hr kg/hr 565.0 256.5 668.9 303.7
Combustion Air required (entire engine) CFM m^3/min 117.0 3.3 236.7 6.7
Charge Air Cooler
Compressor Outlet Temperature ℉ ℃ -- -- -- --
Compressor Flow Rate per CAC lb/hr kg/hr -- -- -- --
CAC Rise over Ambient (Charge)
Specified ℉ ℃ -- -- -- --
Acutal ℉ ℃ -- -- -- --
Max pressure loss across the CAC inH2O kPa -- -- -- --
Maximum Intake Air Temperature (IAT) ℉ ℃ 180.0 82.2 180.0 82.2
ECU IAT Warning ℉ ℃ 169.9 76.6 169.9 76.6
ECU IAT Shutdown ℉ ℃ 180.0 82.2 180.0 82.2
Cooling System
Coolant Capacity
Engine only gal L 2.1 8 2.1 8
Engine with Radiator gal L 4.2 16 4.2 16
Engine Coolant Flow gal/min L/min 54.2 205 54.2 205
Water Pump Speed RPM 1860 2232
Standard Thermostat Range
Cracking Temperature ℉ ℃ 167.0 75 167.0 75
Full Open Temperature ℉ ℃ 194.0 90 194.0 90
Maximum Allowable Pressure Cap psi bar 13.2 0.9 13.2 0.9
Ambient Clearance Open Genset (water) (Air-to-Boil)
Specified ℉ ℃ ≥107 ≥42 ≥107 ≥42
Acutal ℉ ℃ 122.7 50.4 125.8 52.1
Maximum Allowable Top Tank Temperature ℉ ℃ 214.9 101.6 214.9 101.6
ECU Warning ℉ ℃ 204.8 96.0 204.8 96.0
ECU Shutdown ℉ ℃ 214.9 101.6 214.9 101.6
Fan Power HP kW 3.4 2.5 5.4 4.0
Fan Diameter, including blades in mm 24.4 620 24.4 620
Fan Speed RPM 1860 2232
Electrical System
Minimum Recommended Battery Capacity AH 150 150
Cold Cranking Current
Engine only CCA 750 750
Engine with Drive train CCA 750 750
Maximum Allowable Resistance of Starting Circuit Ohms 0.002 0.002
Starting Motor Power HP kW 5.4 4 5.4 4
Battery Charging Alternator
Voltage Volts 14 14
Current Amps 90 90
Coil primary Resistance Ohms 0.59Ω ± 10% 0.59Ω ± 10%
Spark Plug p/n TORCH/R 5498-3 TORCH/R 5498-3
Spark plug gap mm 0.3-0.35 0.3-0.35
Lubrication System
SAE 15W-40 Low Ash Gas engine oil (.25-.5% by wt), API CD/CF or higher;
Oil Specification Please refer Manual Book for different situation.
Oil Pressure
Idle
Min Psi Bar 11.8 0.8 11.8 0.8
Max Psi Bar 17.6 1.2 17.6 1.2
Rated Speed
Min Psi Bar 44.1 3 44.1 3
Max Psi Bar 97.0 6.6 97.0 6.6
Maximum Allowable Oil Temperature ℉ ℃ 239.0 115 239.0 115
Engine Oil Capacity
Min Qts L 14.8 14 14.8 14
Max Qts L 28.5 27 28.5 27
Oil Filter Capacity Qts L 2.1 2 2.1 2
ECU Oil Pressure Warning psi kPa 10 70 10 70
Units Specificaiton
Std Metric 1500 1800
ECU Oil Pressure Shut Down psi kPa 7 49 7 49
Fuel System
Fuel Consumption
3
NG Ft /hr kg/hr 758.1 15.4 900.8 18.3
3
LP Ft /hr kg/hr 836.8 17.0 994.4 20.2
Maximum EPR Rated Pressure psi kPa 1.0 6.9 1.0 6.9
Maximum Running pressure toEPR inH2O kPa 10.8 2.7 10.8 2.7
Minimum Running pressure to EPR inH2O kPa 6.8 1.7 6.8 1.7
Minimum Gas Supply Pipe Size 1-1/4" NPT
Maximum EPR Rated Pressure psi kPa 1.0 6.90 1.0 6.90
Maximum Running Pressure to EPR inH2O kPa 10.8 2.70 10.8 2.70
Minimum Running Pressure to EPR inH2O kPa 6.8 1.70 6.8 1.70
Minimum LPG Supply Pipe Size4 1/4" NPT
700 47
600 41
500 35
Total Fuel(m³/h)
BSFC(g/kW.h)
400 29
300 23
200 17
100 11
0 5
6 16 26 36 46 56 66
Power (kW)
700 16
600 14
500 12
Total Fuel(galloon/h)
BSFC(g/kW.h)
400 10
300 8
200 6
100 4
0 2
7 17 27 37 47 57 67 77
Power (kW)
Units Specificaiton
Std Metric 1500 1800
Fuel Consumption Curve @ 1800 RPM (Natural Gas)
700 47
600 41
500 35
Total Fuel(m³/h)
BSFC(g/kW.h)
400 29
300 23
200 17
100 11
0 5
8 17 26 35 44 53 62 71 80
Power (kW)
600 14
500 12
BSFC(g/kW.h)
300 8
200 6
100 4
0 2
8 18 28 38 48 58 68 78 88
Power (kW)
1
Standby and overload ratings based on ISO3046.
2
All ratings are gross flywheel horsepower corrected to 77oF at an altitude of 328 feet with no cooling fan or alternator losses using heating value for NG of 1025
BTU/SCF (HHV) and for propane of 2490 BTU/SCF (HHV).
3
Production tolerances in engines and installed components can account for power variations of +/- 5%. Altitude, temperature and excessive exhaust and intake
restrictions should be applied to power calculations. Engine maybe operated at : up to 1200 feet and 86°F without power deration. For sustained operation above these
conditions, derate by 2.5% per 1000 feet, and 1.5% per 10°F.
4
The preceeding pipe sizes are only suggestions and piping sizes may vary with temperature, pressure, distance from supply and application of local codes. Gas must
be available at adequate volume and pressure for engine at the EPR.