Professional Documents
Culture Documents
Service Manual: Home Audio System
Service Manual: Home Audio System
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS BLUETOOTH section Lithium-ion battery section Standby power consumption:
When BLUETOOTH standby mode is
POWER OUTPUT AND TOTAL HARMONIC Communication system: Normal voltage: 14.4 V
set to off: 0.5W (eco mode)
DISTORTION: BLUETOOTH Standard version 4.2 Normal capacity: 2500 mAh, 36 Wh
When BLUETOOTH standby mode is
(The United States model only) Output: Maximum charging current: 1 A
set to on: 1.5 W (all wireless network
Left/Right Channel: BLUETOOTH Standard Power Class 2 Maximum charging voltage:
ports on)
With 3 ohms loads, both channels Maximum output power: 16.7 Vdc
Dimensions (W/H/D) (Approx.):
driven at 1 kHz; rated 15 watts per < 20.0 dBm
264 mm × 552 mm × 272 mm
channel minimum RMS power, with Maximum communication range:
no more than 1% total harmonic Line of sight approx. 10 m (33 feet) 1)
Usage life of the lithium-ion 10 in × 21 in × 10 in)
battery Mass (Approx.):
distortion from 250 milliwatts to Frequency band:
8 kg (17 lb 11 oz)
rated output. 2.4 GHz band (2.4000 GHz –
Quantity of the system:
2.4835 GHz) When the Speaker Lights are turned off: 1 piece
Modulation method: 3.5 hours (at the maximum volume
Speaker section FHSS (Freq Hopping Spread
Supplied accessories:
level) AC power cord (1)
Tweeter: 60 mm (2 in) × 2, cone type Spectrum) 5 hours (at the maximum volume
Woofer: 130 mm (5 in) × 2, cone type Compatible BLUETOOTH profiles 2): level with the STAMINA (RU)
A2DP (Advanced Audio Distribution mode turned on) Условия хранения:
Inputs Profile) 14 hours (at volume level 17) Товары сохраняют в упакованном
AVRCP (Audio Video Remote Control виде в темных, сухих, чистых,
AUDIO/PARTY CHAIN IN L/R:
Profile) When the Speaker Lights are turned on: хорошо вентилируемых
Voltage 2 V, impedance 10 kilohms
HFP (Hands-free Profile) помещениях, изолированных от
MIC: 3 hours (at the maximum volume
HSP (Headset Profile) мест хранения кислот и щелочей.
Sensitivity 1 mV, impedance level)
SPP (Serial Port Profile) Температура хранения:
10 kilohms The times given above:
Supported codecs: от -10°C до + 45°C
SBC (Sub Band Codec) — were measured using a predetermined Относительная влажность
music source.
Outputs AAC (Advanced Audio Coding)
— may vary depending on the playback
хранения: от 30% до 70%
AUDIO/PARTY CHAIN OUT L/R: LDAC content. Срок хранения не установлен.
1)
Voltage 2 V, impedance 600 ohms The actual range will vary depending on Рабочая температура:
— will be shortened if you charge and
factors such as obstacles between devices, от 5°C до 35°C
discharge the battery repeatedly.
magnetic fields around a microwave oven,
Рабочая относительная
USB section and supported static electricity, reception sensitivity,
antenna’s performance, operating system, General влажность: от 30% до 70%
audio formats software application, etc. Power requirements:
(USB) port: 2)
BLUETOOTH standard profiles indicate the Design and specifications are subject to
North American model: AC 120 V,
purpose of BLUETOOTH communication change without notice.
Type A, maximum current 2.1 A 60 Hz
Supported bit rate: between devices.
Other models: AC 120 V 240 V,
MP3 (MPEG1 Audio Layer-3): 50/60 Hz
32 kbps 320 kbps, VBR NFC section Power consumption:
WMA: 32 kbps 192 kbps, VBR 55 W
Maximum output power:
Sampling frequencies:
< 60 dBμA/m at 10 m
9-896-413-01
2017G33-1
© 2017.07 Sony Video & Sound Products Inc.
GTK-XB60
SAFETY CHECK-OUT
License and Trademark After correcting the original service problem, perform the follow-
Notice ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
t MPEG Layer-3 audio coding screws, and all other exposed metal parts for AC leakage.
technology and patents licensed Check leakage as described below.
from Fraunhofer IIS and Thomson.
t Windows Media is either a registered LEAKAGE TEST
trademark or trademark of Microsoft
The AC leakage from any exposed metal part to earth ground and
Corporation in the United States
and/or other countries. from all exposed metal parts to any exposed metal part having a
t This product is protected by return to chassis, must not exceed 0.5 mA (500 microamperes.).
certain intellectual property rights Leakage current can be measured by any one of three methods.
of Microsoft Corporation. Use or 1. A commercial leakage tester, such as the Simpson 229 or RCA
distribution of such technology WT-540A. Follow the manufacturers’ instructions to use these
outside of this product is prohibited
without a license from Microsoft or
instruments.
an authorized Microsoft subsidiary. 2. A battery-operated AC milliammeter. The Data Precision 245
t The BLUETOOTH® word mark and digital multimeter is suitable for this job.
logos are registered trademarks 3. Measuring the voltage drop across a resistor by means of a
owned by Bluetooth SIG, Inc. and VOM or battery-operated AC voltmeter. The “limit” indication
any use of such marks by Sony is 0.75 V, so analog meters must have an accurate low-voltage
Corporation is under license. Other
trademarks and trade names are
scale. The Simpson 250 and Sanwa SH-63Trd are examples
those of their respective owners. of a passive VOM that is suitable. Nearly all battery operated
t The N-Mark is a trademark or digital multimeters that have a 2 V AC range are suitable. (See
registered trademark of NFC Forum, Fig. A)
Inc. in the United States and in other
countries. To Exposed Metal
t Google Play and Android are Parts on Set
trademarks of Google Inc.
t LD AC™ and LDAC logo are
trademarks of Sony Corporation.
t Apple , the Apple logo, iPhone, and
iPod touch are trademarks of Apple
Inc., registered in the U.S. and other
countries. App Store is a service AC
mark of Apple Inc. 0.15 μF 1.5 kΩ voltmeter
t “Made for iPod” and “Made for (0.75 V)
iPhone” mean that an electronic
accessory has been designed to
connect specifically to iPod or
iPhone, respectively, and has been
certified by the developer to meet
Earth Ground
Apple performance standards. Apple
is not responsible for the operation Fig. A. Using an AC voltmeter to check AC leakage.
of this device or its compliance with
safety and regulatory standards.
Please note that the use of this
accessory with iPod or iPhone may
affect wireless performance.
t WALKMAN and WALKMAN logo
are registered trademarks of Sony
Corporation.
t All other trademarks and registered
trademarks are of their respective
holders. In this manual, TM and ®
marks are not specified.
SAFETY-RELATED COMPONENT WARNING!
2
GTK-XB60
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 4 4-10. Schematic Diagram - MAIN Board (7/8) - ..................... 30
4-11. Schematic Diagram - MAIN Board (8/8) - ..................... 31
2. DISASSEMBLY 4-12. Printed Wiring Board - NFC Board - .............................. 32
2-1. Disassembly Flow ........................................................... 6 4-13. Schematic Diagram - NFC Board -................................. 32
2-2. Side Panel L, Lithium Ion Battery Connector (XP3)...... 7 4-14. Printed Wiring Board - BT Board -................................. 32
2-3. Lithium Ion Battery ........................................................ 7 4-15. Schematic Diagram - BT Board - ................................... 33
2-4. Side Panel R .................................................................... 8 4-16. Printed Wiring Board - KEY Board -.............................. 34
2-5. Top Panel Block .............................................................. 8 4-17. Schematic Diagram - KEY Board - ................................ 35
2-6. POWER Board ................................................................ 9 4-18. Printed Wiring Board - MIC KNOB Board - .................. 36
2-7. MIC KNOB Board .......................................................... 9 4-19. Schematic Diagram - MIC KNOB Board - .................... 36
2-8. MAIN Board ................................................................... 10 4-20. Printed Wiring Board - TOP SPEAKER Board -............ 37
2-9. Board Block .................................................................... 11 4-21. Schematic Diagram - TOP SPEAKER Board - .............. 37
2-10. NFC Board ...................................................................... 12 4-22. Printed Wiring Board
2-11. Top Handle ...................................................................... 12 - BOTTOM SPEAKER Board - ..................................... 37
2-12. KEY Board...................................................................... 13 4-23. Schematic Diagram - BOTTOM SPEAKER Board - ..... 37
2-13. BT Board......................................................................... 13 4-24. Printed Wiring Board - TOP LED Board -...................... 38
2-14. Bottom Panel Assy .......................................................... 14 4-25. Schematic Diagram - TOP LED Board - ........................ 38
2-15. Front Panel Block-1 ........................................................ 15 4-26. Printed Wiring Board - BOTTOM LED Board - ............ 39
2-16. Front Panel Block-2 ........................................................ 16 4-27. Schematic Diagram - BOTTOM LED Board - ............... 39
2-17. Speaker Unit (WF) .......................................................... 17 4-28. Schematic Diagram - POWER Board - .......................... 40
2-18. TOP SPEAKER Board, BOTTOM SPEAKER Board, 4-29. Printed Wiring Board
TOP LED Board, BOTTOM LED Board ....................... 18 - POWER Board (US and CND models) - ..................... 41
2-19. Speaker Unit (TW).......................................................... 19 4-30. Printed Wiring Board
- POWER Board (Except US and CND models) - ......... 42
3. TEST MODE ............................................................ 19
5. EXPLODED VIEWS
4. DIAGRAMS 5-1. Side Panel Section .......................................................... 43
4-1. Block Diagram - OVERALL Section - ........................... 20 5-2. Speaker Cabinet Section ................................................. 44
4-2. Block Diagram - POWER SUPPLY Section - ................ 21 5-3. Top Panel Section ........................................................... 45
4-3. Printed Wiring Board - MAIN Board - ........................... 23 5-4. Board Section .................................................................. 46
4-4. Schematic Diagram - MAIN Board (1/8) - ..................... 24 5-5. Front Panel Section ......................................................... 47
4-5. Schematic Diagram - MAIN Board (2/8) - ..................... 25
4-6. Schematic Diagram - MAIN Board (3/8) - ..................... 26 6. ELECTRICAL PARTS LIST .............................. 48
4-7. Schematic Diagram - MAIN Board (4/8) - ..................... 27
4-8. Schematic Diagram - MAIN Board (5/8) - ..................... 28 Accessories are given in the last of the electrical parts list.
4-9. Schematic Diagram - MAIN Board (6/8) - ..................... 29
3
GTK-XB60
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
MAIN board
– Rear view –
lithium ion
battery MODEL NUMBER LABEL
connector
SONY®
(XP3)
Destination
Destination Part No.
code
US, CND models (UC2) 4-697-233-0[] UC2
AEP, UK, models (CEL, CEK) 4-697-234-0[] CEL/CEK
rear side
left side AUS, RU models (AU1, RU1) 4-697-235-0[] AU1/RU1/SP6
4
GTK-XB60
Notes
• It may take longer to charge the battery
depending on the conditions of use.
RESETTING THE SYSTEM
• Even if you do not intend to use the
If the system doesn’t respond and system for a long time, charge the battery
cannot be operated despite the power to its full capacity once every six months
being on, reset the system using the to maintain its performance.
RESET button. • In an extremely cold or hot environment,
charging stops for safety.
1 Press RESET on the rear of If charging is taking a long time, this also
stops the system from charging.
the unit with a pin or other In these conditions, the CHARGE indicator
pointed object. continues to flash quickly in amber, but
this is not a malfunction.
To resolve these issues, disconnect the
AC power cord and connect it again in an
operating temperature between 5°C and
35°C (41°F and 95°F).
Hint
You can operate the system while it is
charging.
5
GTK-XB60
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
SET
JIG
When disassembling the unit, use the following
jig for speaker removal.
6
GTK-XB60
Note: Follow the disassembly procedure in the numerical order given.
front side
MAIN board
4 five claws
front side 1 two rubbers
(See Fig. A)
7 lithium ion 4 four 2 two screws
battery claws (M3 u 10)
connector
(XP3)
2 screw
rear side left side (M3 u 10)
+RZWRUHPRYHWKHUXEEHU
Note: When removing the rubber, insert a
sharp-tipped object such as tweezers
into the cutout.
rear side
)LJ$!
3 three screws
tweezers, etc.
(M4 u 20)
5 Remove the side panel L two bosses
in the direction of the arrow. (with two
rubbers)
two bosses
(with two rubbers)
rubber
4 cushion
(battery cable)
rear side Note 1: This parts cannot be reused.
When replacing the lithium
3 Remove the lithium ion battery block 6 lithium ion battery ion battery, be sure to replace
in the direction of the arrow. them with new parts
hole simultaneously.
5 two cushions (battery)
Note 1: This parts cannot be reused.
When replacing the lithium ion battery,
be sure to replace them with new parts hole left side
simultaneously.
2 battery cover
Note 2: When installing the battery cover, 1 four screws
align the two bosses and two holes. (M4 u 20)
7
GTK-XB60
4 four claws
6 side panel R
2 two screws
(M3 u 10)
1 two foot pads two bosses
(circle) (with two rubbers) top side
2 screw
(M3 u 10) 4 five
claws
front side
3 two screws
(M4 u 20)
two bosses
(with two rubbers)
1 two foot
pads
(circle)
3 three screws
(M4 u 20)
4 four claws
rear side
1 screw
top side (M3 u 10)
3 FFC (BT-MAIN)
(XP35)
2 Remove the top panel block
in the direction of the arrow. terminal side 4 claw
front side
rear side
8
GTK-XB60
3 two screws
3 two screws (3 u 6)
(3 u 6) hole
1 POWER board cable
5 POWER board connector (XP20)
Note: When installing the POWER
board, align the rib and hole.
4 Remove the POWER board
in the direction of the arrow.
rib
top side
2 two screws
(M3 u 10)
front side
rear side
5 two screws
3 MIC KNOB board block 1 MIC KNOB board cable 6 party chain hole (M3 u 10)
connector (XP4) button&lens
boss hole
4 MIC knob
rear side
rotary encoder
9
GTK-XB60
9 MAIN board
Note: When installing the MAIN board,
align the rib and hole.
B
hole A
6 four screws
(3 u 6)
MAIN
right side board
B XP20
3DVWLQJSRVLWLRQRIWKHWKHUPDOVKHHW
When affixing the thermal sheet, affix so that the entire
projection of the bottom shell is covered.
)LJ%!
thermal sheet
10
GTK-XB60
terminal side
top side
MAIN
board
4 four screws
(M4 u 20)
rear side
5 board block
11
GTK-XB60
hook
–%RWWRPYLHZ– rear side
top panel block
4 Remove the NFC board in
front side
the direction of the arrow.
hook
top panel block
rear side
top side
adhesive sheet 2 claw
cushion
1 cushion
rear side
boss
front side
top side
12
GTK-XB60
3 seven screws
(M3 u 10)
3 three screws
(M3 u 10)
hole
7 KEY board
Note: When installing the KEY board,
align the two bosses and two holes.
terminal
2 KEY board cable
side
connector (XP12) hole
2-13. BT BOARD
Note 1: When replacing the BT board, be sure to replace the BT board
and the NFC board simultaneously. The BT board cannot re-
place with single. Among the repair parts, the BT board and 4 Gradually peel off the BT board with
the NFC board are supplied as one unit. a flathead screwdriver, etc.
Note 3: The BT board is affixed to the top panel with
a adhesive sheet.
When removing the BT board, remove slowly
so that you do not damage the boss, etc. of the
top panel.
1 cushion
BT board
terminal flathead
2 microphone cable
side screwdriver,
connector (XP6)
etc.
top panel block rear side
front side
6 BT board
hole Note 2: When installing the BT board,
align the two bosses and two
3 FFC (BT-KEY) holes.
(XP10)
adhesive
front side top side sheet hole
13
GTK-XB60
Note 1: When removing the bottom panel assy, move the bottom
panel assy slowly and remove the bond as shown figure.
Note 2: When removing the bottom panel assy, please remove
carefully so as not to damage the four bosses.
top side
front side
bottom side
3 screw
(M3 u 10)
3 screw
bond (M3 u 10)
2 two screws
(M4 u 20)
1 two foot pads
(flat)
14
GTK-XB60
front side
1 two screws
(M4 u 20)
front panel block
bottom side
1 two screws
wood cabinet
(M4 u 20)
top side
– Bottom view –
– Top view –
15
GTK-XB60
Note 1: Make sure to proceed with the top and bottom 1 Insert a thick screwdriver into the left side
sides first because the right and left sides may and widen the gap (perform at two places).
damage the sides of the front panel block. Note 2: Be careful because if a screwdriver is
inserted too far in, the speaker unit (WF)
front panel block
may get damaged.
bottom side
left side
wood cabinet
tweeter cable
woofer cable
Note 5: This boss excludes US wood cabinet – Top view – woofer cable
and CND models.
16
GTK-XB60
:RRIHUFDEOHVHWWLQJZRRIHUWRS
Note 2: When installing the woofer cable, make the
position of caulking of terminals is outside.
top side terminal (wide)
woofer cable
[red line]
3 terminal
(narrow)
wood cabinet
2 Pull out the speaker unit (WF)
in the direction of the arrow.
,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUXQLW:)
Note 1: When installing the speaker unit (WF), make sure 4 speaker unit (WF)
3 terminal (woofer bottom)
that there is a position of the speaker terminal to
the position shown in the figure below. (wide)
top side
terminals
position :RRIHUFDEOHVHWWLQJZRRIHUERWWRP
Note 2: When installing the woofer cable, make the
position of caulking of terminals is outside.
speaker unit (WF) woofer cable
(woofer bottom) [yellow line] terminal (wide)
17
GTK-XB60
2-18. TOP SPEAKER BOARD, BOTTOM SPEAKER BOARD, TOP LED BOARD, BOTTOM LED BOARD
/('ERDUGFDEOHDQG
WZHHWHUFDEOHVHWWLQJ 3 Remove the LED+SPEAKER board
block in the direction of the arrow.
boss top side
OK
top side
front side
groove 8 TOP LED board
Note: When installing the TOP LED
board, align the two bosses and
two holes. boss
hole
groove
boss
left side
hole
6 LED board cable
hole connector (XP12)
18
GTK-XB60
SECTION 3
TEST MODE
2-19. SPEAKER UNIT (TW) Buttons and indicators position: SOFTWARE VERSION
It can confirm the software version.
7ZHHWHUFDEOHDQG/('ERDUGFDEOHVHWWLQJ STAMINA FUNCTION USB AUDIO IN L R ADD
OK Procedure:
top side 1. Press the [1] button to turn the power on.
2. Press the [FUNCTION] button to select the AUDIO IN func-
tion.
groove
3. Press two buttons of the [u] and [ADD] simultaneously for
5 seconds.
4. Each software version are shown by the flashing frequency of
left side LEDs simultaneously.
NG Example:
• When the MCU version is “v12”, the [ADD L] LED flashes 1
time, the [ADD R] LED flashes 2 times.
top side
Flash ADD
(1 time) L R
groove Flash
(2 times)
front side
• When the MPEG version is “v14”, the [STAMINA] LED
CHARGE – Top view – flashes 1 time, the [CHARGE] LED flashes 4 times.
groove
CHARGE
USB AUDIO IN
flash
(2 times)
flash
(2 times)
GTK-XB60
19 19
GTK-XB60
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM - OVERALL Section -
DAC OP
Audio Out&Party Chain
AK4430 AS9632
From
MCU
WL
DATA4 IIC1
Audio IN
ADC TL
PCM1808
DATA0 PWM1
MCLK5 AMP
BCLK5 IC WR
FLASH 8M
01U0FLASH - 202 LRCLK5 Audio TAS53
Processor 42A
MPEG crystal XI,XO TR
TAS5538
Decoder 24.576MHz DATA5
XI,XO PWM2
crystal SPHE81
BCLK1
01UCRYSTA- 502 07C
LRCLK1
DSP
DATA1 BCLK3
Embedded YSS952 AC:BTL 75W*2(3ȍ) 10%
SW USBP,USBM SW LRCLK3
USB SDRAM Battery:BTL 35W*2(3 ȍ) 10%
NX3DV42GU 74L DATA3
BCLK2 VC2 DATA7
LRCLK2 44
Hands Free ADC
DATA2 OP MIC*1
PCM
F4558
UART2 1808
IIC1
ADC
Reset IC
BT_RST DATA6 PCM
BT UART1 Sampler
SGM803 BM63 -3G 1808 IC
RESET¥&MF IIC2 AM4KA340
CP IC IIC3 B
MF133 &NFC_INT
7S3959
MCU
IIC1 LED Driver PWM* 16
For RGB_LED*4&White_LED*4
NFC NFC_INT STM32F091 SN3218
MN63Y1212
VC IO*1
For Blue_LED(BT)
Buttom*10 IO*5
For White_LED*5(USB*1+Audio IN*1+L/R*2+Party Chain*1)
AD*2 +GPIO*1 IO*1
For RED_LED(Bass)
IO*1
Reset Button For Amber _LED(Charge)
IO*2
Reset For Red+Green(Stanby)_LED(Charge)
ROM:256K bytes IO*21 For O thers
crystal XI,XO
01UCRYST
RAM:32K bytes Mic Knob
A- 201
GTK-XB60
20 20
GTK-XB60
For TAS5342A
AC MOS 3.3V_D2
For SPHE8107C&Flash
POWER Board I/O*1 AP2305
From MCU
23 ± 0.5V STB_5V
LDO 1.25V_D
DC-DC SGM2032 For SPHE8107C
TPS54240
Triode 5V_D1
I/O*1 BT3906 For PCM1808*3
From MCU
M
O
M For & Blue_LED(BT)&Green LED*2(Wired PartyChain*1+STAMINA*1)
Charge IC S
BQ24610 O Amber_LED(Charge)& Red+Green LED(Stanby)&RED_LED(Bass)
(0.3C/0.05C) S White_LED*5(USB*1+Audio IN*1++L/R*2+Party Chain*1)
M
O
S 5V_D3
MOS
I/O*1 EUP3504 For RGB LED*4&Flash White LED *4&SN3218
Battery(4 pieces) From MCU
(14.4V&2500mAh)
2500mA Bat_14.4V STB_12V
MOS 12V_D
I/O*1 For TAS5342A&74HC4052)&F4558
AP2315
From MCU
P_USB5V
DC-DC USB USB_5V
TPS54240 OCP IC For USB
G527
I/O*1 From MCU (2.1A)
From MCU
USB Charge IC
TPS2511 USB_5V For USB
I/O*2 (2.1A)
From MCU
TBD
GTK-XB60
21 21
GTK-XB60
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards. For Schematic Diagrams. NFC board
Note: Note: MAIN board
• : Pattern from the side which enables seeing. • All capacitors are in μF unless otherwise noted. (p: pF) 50 MIC KNOB board
KEY board
(The other layers’ patterns are not indicated.) WV or less are not indicated except for electrolytics and
tantalums.
Caution: • All resistors are in Ω and 1/4 W or less unless otherwise
Pattern face side: Parts on the pattern face side seen specified.
(Conductor Side) from the pattern face are indicated. BT board POWER board
Parts face side: Parts on the parts face side seen from Note: Note:
(Component Side) the parts face are indicated. The components identi- Les composants identifiés TOP LED board
fied by mark 0 or dotted par une marque 0 sont
Note: Among mounted electrical parts on each board, only line with mark 0 are criti- critiques pour la sécurité.
parts that are described in the electrical parts list can be cal for safety. Ne les remplacer que par TOP SPEAKER board
replaced for repairing. Replace only with part une pièce portant le nu-
The parts that are not described in the electrical parts number specified. méro spécifié.
list cannot be replaced with single for repairing.
In that case, replace the complete mounted board. Note: Among mounted electrical parts on each board, only
Printed wiring board that has been described on this parts that are described in the electrical parts list can be
service manual are for reference. replaced for repairing.
The parts that are not described in the electrical parts
list cannot be replaced with single for repairing.
In that case, replace the complete mounted board.
Schematic diagram that has been described on this ser-
vice manual are for reference.
GTK-XB60
22 22
GTK-XB60
4-3. PRINTED WIRING BOARD - MAIN Board - • See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10
MAIN BOARD (COMPONENT SIDE)
GTK-XB60
23 23
GTK-XB60
1 2 3 4 5 6 7 8 9
R957
NC/10K C78 C76
XP20
100pF/50V/NP0
0.1uF/50V/X7R
7
7
POWER INPUT 6
6
5
5 4
4 3
3 2
2 1
1 V_12V
7PIN/2.0mm
U21
TPS54240 PW_MAIN TPS54240 USB_5V
PW_MAIN
B FB5 0
1
2
3
4
BOOT
VIN
EN
PH
GND
COMP
10
9
8
7
R29 100
C37 C13
470pF/50V/X7R470pF/50V/X7R
+12V
FB2 0
1
2
3
4
BOOT
VIN
EN
PH
GND
COMP
10
9
8
7
L16 10uH
R5
49.9K/1%
5 SS/TR VSNS 6 5 SS/TR VSNS 6
RT/CLC PWRGD L2 RT/CLC PWRGD
PwPG
PwPG
1 2 D6 MBRX180/80V/1A
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
R2 R1
200K STB_5V NC/200K
R35 R20 R25
12
13
14
11
15
16
12
13
14
11
15
16
3 R6
CE5
C23
NC/56 20K NC/56 C6
POWER_EN +
9.1K/1%
22uH-48uH POWER_EN
D1
220uF/25V
CE15 100uF/50V
CE3
0.1uF
R8 SS34B 3A/40V 10uF
C69 1UF/100V/X7R
C28 1UF/100V/X7R
R34
C33 0.1uF/50V/X7R
C3
ZD4
+ 49.9K/1% + U15 C109
C31
C32
20K
NC/330pF/50V/X7R
100uF/50V
0.1uF/50V/X7R
CE7
C36 R72 C26 R69
R103 R99
0.1uF
0.1uF/16V/X7R
ZMM5V6/5.6V
33K 200K R7 R97 + 22K 200K
0.1uF CE4 C9 0.1uF
C20 C110 D9 + C15
220uF/25V
4.7K/1%
4.7K/1%
SS34B 3A/40V
100uF/16V
NC/330pF/50V/X7R
3300pF/50V/X7R
3300pF/50V/X7R
10uF
+12V V_12V
R4
C203
C389
1 4
EN VOS R335 R841
3 47K/1%
100pF/50V/NP0
33pF/50V/NP0
2.2uF
FB D5
5 2 10K 2 3.3V_D1_EN
GND PG CE12C48 C391
+
3
100uF/16V
1000pF/50V/X7R
10uF/6.3V/X5R
1 5V_D1_EN
R336
POWER_EN1 R239 10K Q4
15K 1.2V_D
D
NPN_3DG3904M
BAT54C
VOUT=0.8*(47+15)/15=3.3V
C21
R236 U4
47K 0.1UF 3.3V_D2 SGM203-2ADJ3
STB_5V 5V_D1 1 5
VIN VOUT
STB_5VĺSTB_3.3V Q226
R57
8.2K/1%
PNP_3CG3906M 3 4
POWER CONTROL 12V R839
C25 EN ADJ/SENSE
GND
10UF/6.3V/X5R C47
10K
2
R58 C84 10UF/6.3V/X5R
10K 0.1UF R22
STB_3.3V 3.3V_D2
15K
STB_3.3V 3.3V_D1 S D R206
Q13 1K
C127 R43
G
P_AP2305
S D 0.1UF 100K 5V_D1_EN
Q11
C29 R10
G
P_AP2305
0.1UF
E
100K
R204
1K Vout=0.8*(8.2/15+1)=1.24V
R203
4.7K R28 10K Q17 STB_5V 5V_D2
3.3V_D2_EN
NPN_3DG3904M
3.3V_D1_EN C41 S D
R27 Q14
47K 0.1UF C163 R75
G
P_AP2305
0.1UF 100K
47K 0.1UF
C16 R23
F
3 4
10uF/6.3V/X5R
15K/1%
GND C30
POWER CONTROL 5V
2
0.1UF
10uF/6.3V/X5R
R19
12K/1%
Vout=0.8*(1+15/12)=1.8V
3.3Vĺ1.8V
GTK-XB60
24 24
GTK-XB60
1 2 3 4 5 6 7 8
PLL_VDD12
C44 8 8 8
C42
VDD33_ADAC
10uF/6.3V/X5R
DATA1
BCLK1
0.1UF
LRCK1
MAX 190mA @ripple 50mV D_3V3
3.3V_D2
B FB12 500/800mA
LRCLK1
DATA1
BCLK1
C43 C82
0.1UF
10uF/6.3V/X5R
VDD33_USB
NOTE:
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
FB13 500/800mA When 8107H/S,
Pin60/61 are SPDIF_IN2,
UART2_CTS/GPIO25
UART2_RX/GPIO24
I2S_OUT_D2/A_PWM6/GPIO17
I2S_OUT_D1/A_PWM5/GPIO16
I2S_OUT_D0/A_PWM4/GPIO15
I2S_OUT_BCK/A_PWM3/GPIO14
I2S_OUT_MCK/A_PWM2/GPIO13
I2S_OUT_LRCK/A_PWM1/GPIO12
UART2_TX/GPIO23
SPDIF_OUT/GPIO11
AUDIO_MUTE/GPIO10
ADAC_AVDD
ADAC_VSS
GPIO22
GPIO21
GPIO20
A_PWM8/GPIO19
A_PWM7/GPIO18
AOUT_L/GPIO138
C45 C66
10uF/6.3V/X5R 0.1UF SPDIF_IN1
VDD33_ADAC When 8107C,
Pin60/61 is GPIO.
FB8 500/800mA
3.3V_D2 58 38
SF_3V3 59 UART2_RTS/GPIO30 AOUT_R/GPIO137 37 A_VREF
C46 C49
60 BT_EN/GPIO31 VREF 36
22uF/6.3V/X5R 0.1UF SPDIF_IN2/GPIO32 AADC_VSS
61 35
SPDIF_IN1/GPIO33 AADC_AVDD VDD33_AADC
62 34 MIC_BIAS
VDD33_AADC 63 CARD_SENSE/GPIO34 MIC_BIAS 33
R59
R91
C531000pF/50V/X7R
SF_3V3 64 SD_D0/GPIO35 MIC_IN 32 AL_CH1
SD_CLK/GPIO36 AIN_L0 TP17 6
C
65 31 AR_CH1
SD_CMD/GPIO37 AIN_R0 TP18 6
66 30
4.7K
4.7K
FB9 500/800mA UART0_TX
UART0_RX 67 UART0_TX/GPIO38 AIN_L1 29 6
68 UART0_RX/GPIO39 AIN_R1 28 6
C54
22uF/6.3V/X5R
C52
0.1UF R202 4.7K
SF_CS
SF_DO 69 SPI_CE/HW_CFG
SPI_D0
8107H/S/C-76 PLL_VDD12
CLKIN
27 CLKIN
PLL_VDD12
SF_CK 70 26 CLKOUT
SF_DI 71 SPI_CLK/HW_CFG CLKOUT 25
SPI_D1 USB_AVDD VDD33_USB
72 24 USB_DP USB_DP
73 VFD_CLK/PWM0/GPIO44 USB_DP 23 USB_DM USB_DM
I2C1_SDA/UART1_RX/GPIO65
VFD_STB/PWM1/HW_CFG/GPIO45 USB_DM
I2C1_SCL/UART1_TX/GPIO64
74 22 SAR_ADI0
75 VFD_DAT/PWM2/GPIO46 SAR_ADI0/GPIO134 21 SAR_ADI1
76 IR_IN/GPIO47 SAR_ADI1/GPIO135 20 SAR_ADI2
VDD12
RESET CIRCUIT HW Config
VDD12 SAR_ADI2/HDMI_HPD/GPIO136
POWER_KEY/GPIO61
I2S_IN_LRCK/GPIO71
I2S_IN_MCK/GPIO70
I2S_IN_BCK/GPIO69
D_3V3
HDMI_CEC/GPIO72
SPDIF_IN0/GPIO63
I2S_IN_D2/GPIO66
I2S_IN_D1/GPIO67
I2S_IN_D0/GPIO68
must be pull high
HEAC-/GPIO132
77 SAR_ADI2 A_VREF MIC_BIAS
EPAD SAR_ADI1
R94 4.7K
R111 100 RESET_B SAR_ADI0
RESET_B
C68
C96 C97 C98
GPIO62
HEAC+
VDD33
10UF/6.3V/X5R
C65 C74
10UF/6.3V/X5R
0.1UF
C55
NC
NC
NC
0.1UF
C57
1000pF/50V/X7R
1000pF/50V/X7R
1000pF/50V/X7R
U6
22UF/6.3/X5R C56
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Q7 0.01uF/50V/X7R
R106 100 QFN76-354354-0.4
Voltage Reference
D
NPN_3DG3904M
NOTE:
MPEG_TX
MPEG_RX
NOTE:
Close To 8107 Pin For ESD
RESET_B
Close To 8107 Pin
R71
D8
LL4148
6.8K
D_3V3
MPEG_TX
MPEG_RX
Crystal
R64 4.7K
D_3V3
Y1 24.576MHz/10PPM
R68
CLKIN 1 3 CLKOUT
Uart0 Debug Interface 100
4
3.3V_D2
C77 C58
R108
R102
C59
FB18 500/800mA layout
4.7K
XP2
10K
10K
U9 1
E
SF_CS 1 8 0.1UF UART0_TX 2 1
SF_DO 2 CE# VDD 7 R96 4.7K UART0_RX 3 2
SO HOLD# SF_3V3 3
3 6 SF_CK 4
4 WP# SCK 5 SF_DI 4
VSS SI 4PIN/2.0mm
EN25T16A-75HIP 16M SERIAL FLASH
GTK-XB60
25 25
GTK-XB60
1 2 3 4 5 6 7 8 9
51K
R140 0
MIC_GND
3.3V_D1
GND
R133
C70 330pF/16V/NP0
MIC_DET
10K C240 C258
R90 47K R134 10K
10uF/6.3V/X5R
0.1UF
B
P3
R139 C73 5V_D1
5
DET1
4
4 MIC_DET R117 1 14 MIC_IN
DET1 C71 4.7uF/10V/X5R 47pF/50V/NP0 VREF VINR
2 2 - 4.7uF/10V/X5R 2 13
SIN AGND VINL
3.3K 1 C95 R130 1.8K R316 4.7 3 12
3 100K 3 + FB11 4.7 4 VCC FMT 11
SGND 3.3V_D1 VDD MD1
4
7 C63 U930A 5 10
DET2 DGND MD0 10
8 F4558 6 10 R62 33 6 9 R78 33
1000pF/50V/X7R
DET2
-
C269 4.7uF/10V/X5R MCLK5 DATA7
SCKI DOUT
8
C88 7 R109 1K MIC_IN LRCK5 R63 33 7 8 R79 33 BCLK5
10 LRCK BCK 10
REF 5
1000pF/50V/X7R
+
1 U930B
GND
REF
C282 1000pF/50V/X7R
F4558 R110 C228C222 C192 C186 U28
C80
8
7PIN/CKX-064-13SA02H
C64 0.1UF PCM1808
10uF/6.3V/X5R
10uF/6.3V/X5R
0.1UF 0.1UF
R89
10NF
10K 680
R270 0
R271 0
MIC KNOB
C
STB_3.3V
R105
R150
U10
USB_5V GMT_G527
4.7K
4.7K
XP4
USB_5V 6 1
IN OUT 1 USB_VCC1
USB_EN USB_EN 4 Compatible for footprint KNOB2 KNOB2 1
USB_FAULT 3 EN 2 2 1
USB_FAULT FLG GND 2
5 STB_5V STB_5V 3
ILIM Wired PARTY CHAIN 4 3
+ CE17 C115 Wired PARTY CHAIN
Wired Green_LED 5 4
C81 C75 C11 C90 1uF/16V Wired Green_LED
220uF/16V 5
R151
10uF/16V/X5R
1uF/16V
0.1uF/50V/X7R
1uF/16V
15K/1%
C316 47pF/50V/NP0
C321 47pF/50V/NP0
D
P5 USB_VCC1 5PIN/2.0mm
C7 0.1UF
6
4PIN/2mm
Shell A Shell B
4 FL1 ELE900
R266 VCC 3 4 3 D-
1K/1% D- 2 1 2 D+ C101 C8
ESD10
D+ 1
ESD2
GND
100pF/50V/NP0
0.1uF/50V/X7R
NEW PART
NC/LVE16Y1R0
NC/LVE16Y1R0
R102+R266=16K,Ilim=2.25A_min,2.5A_typ
E CHARGE_SWITCH
USB_5V
BM update_SWITCH
USB_5V
CHG_EN R65 1K
R81
47K BM_update_EN R67 1K
R87
47K
R80 100K
R76
10K R88 100K
R82
C230 100nF 10K
C221 100nF
10
10
9
U14 U23
S
Vcc
OE
Vcc
OE
NX3DV42GU NX3DV42GU
D- 1 7 1 7
D+ HSD2+ D+ HSD2+ BT_DM
D+ 2 6 2 6
D- HSD2- D- HSD2- BT_DP
F
HSD1+
HSD1+
HSD1-
HSD1-
GND
GND
3
5
USB_DP
USB_DM
USB_DP
USB_DM
GTK-XB60
26 26
GTK-XB60
1 2 3 4 5 6 7 8 9
A
R153 33 MCU_3.3V 12
G_SCL 12 11 FB29 70/3A
MCU_3.3V R53 33 11 10
DSP_SDA 10
R52 33 9
STB_3.3V DSP_SCL 9
MCU_3.3V R41 R40 8 FB45 70/3A
R113 1M 8 7
R45 R42 R51 33 7 6 FB32 220 LED-SDA
Close to MCU TAS_SDA 6
FB48 500/800mA Y3 R50 33 5 FB33 220 LED-SCL
TAS_SCL 5
YO R956 1K YI STB_3.3V 4.7K 4.7K 4 FB34 220 LED_SHDNN
C341 C342 C344 C345 C347 4 3 FB35 220 WHITE_LED
14.7456MHz/30PPM 2.2K 2.2K 3 2
G
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
I2C1_SDA R49 33 LED-SDA MCU_RX R135 1K BT_TX 2 1
C112 C113 S D 1
27pF/50V/NP0 30pF/50V/NPO I2C1_SCL
Q49 N_2SK3018 MCU_TX R137 1K BT_RX C151C152C156C157
C241
C119
STB_3.3V 12PIN/1.0mm
NC/15pF/50V/NP0
NC/15pF/50V/NP0
NC/15pF/50V/NP0
NC/15pF/50V/NP0
G
LED-SCL
10PF/50V/NPO
10PF/50V/NPO
R46 33
S D
Q48
N_2SK3018
STB_3.3V MCU_3.3V BAT
TS-1806 TM5
LED_SHDNN
WHITE_LED
BT_RESET
MCU_RX
MCU_TX
TM4
R251
R249
BT_MFB
NFC_BT
PW_LED2
BT Blue_LED
B
I2C1_SDA
I2C1_SCL
PW_LED1
SW1001 MCU_3.3V
SWCLK
MCU_RST R141 1K
MCU_3.3V PW
R132 R205 1M/0.5%
D4 R114 MCU_RST 4.7K 4.7K
10K
LL4148 MCU_3.3V
27K R210
C1040 R248
XP9
100
R408 4 1M 1M/0.5%
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
R128 100 MCU_RST 1000pF/50V/X7R U18 SWDIO 3 4
10K 3
SWCLK 2 PW_Det Bat_Det
VDD
VSS
PE1
PE0
PB9
PB8
PF11-BOOT0
PB7
PB6
PB5
PB4
PB3
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
PC12
PC11
PC10
PA15
PA14
1 2
1
C121 C182
4.7uF 0.1uF/16V/X7R STB_3.3V 4PIN/2.0mm R211 R240
MCU_3.3V C94
Close to MCU
R232 R391 33 1 75 120K/1% 120K/0.5%
VALID I2S_SEL1 2 PE2 VDDIO2 74 NC/10UF/16V/X5R
I2S_SEL2 3 PE3 VSS 73 STAMINA GREEN_LED C60
2.7K/0.5% R392 33 4 PE4 PF6 72 SWDIO
AMP_RESET 0.1uF/50V/X7R
5 PE5 PA13 71 AUX WHITE_LED R250
6 PE6 PA12 70 USB WHITE_LED
R213 7 VBAT PA11 69 CHARGE ORANGE_LED 120K/0.5%
YI 8 PC13 PA10 68 L WHITE_LED
YO 9 PC14_OSC32_IN PA9 67 R WHITE_LED
2.7K/0.5% 10 PC15_OSC32-OUT PA8 66 BASS RED_LED
3.3V_D1 AC_ON_OFF1 PF9 PC9
NTC NTC R215 100 NTC_DET 11 65 Wireless WHITE_LED
12 PF10 PC8 64
C
PF0_OSC_IN PC7 UART7_RX1
R592 13 STM32F091VC 63
MCU_3.3V PF1_OSC_OUT PC6 UART7_TX1
10KMCU_RST 14 62
NTC_DET 15 NRST PD15 61 STAT1 MCU_3.3V
Bat_Det R267 100 16 PC0 PD14 60 STAT2
CE CE_1 KNOB2 17 PC1 PD13 59 R245 100K Q10 PNP_MMBT8550C R159 NFC_INT
KNOB2 PC2 PD12
PG PG_1 R74 R70 Wired PARTY CHAIN 18 58 CE_1
Wired PARTY CHAIN Wired Green_LED 19 PC3 PD11 57 Charge_Current_CTL 100K
Wired Green_LED 20 PF2 PD10 56 PG_1
STAT1 21 VSSA PD9 55 EN
STAT1 MCU_3.3V VDDA PD8
STAT2 STAT2 4.7K 4.7K BUSY 22 54 POWER_ON_OFF C307 1UF
MPEG_RX PF3 PB15 R161
MCU_TX1 23 53 R399 33 Party_Chain_In
MCU_RX1 24 PA0 PB14 52
MPEG_TX PA1 PB13 Party_Chain_Out
Charge_Current_CTL Charge_Current_CTL 25 51
10K
AMUTE PA2 PB12 Party_Chain_SW
BAT__Ctr BAT__Ctr 100K
C122 10uF/6.3V/X5R
470K
UART2_RX1
UART2_TX1
C24
C118
C103
C104
R160
PE10
PE11
PE12
PE13
PE14
PE15
PB10
PB11
VDD
VDD
VSS
VSS
PC4
PC5
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2
PE7
PE8
PE9
Q9
R162
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NFC_INT0 R163 100K
NPN_3DG3904M
R201
R403
R390
I2C2_SDA
I2C2_SCL
C231 C232
R156
R147
R393
D
1M
R394
100pF/50V/NP0
1000pF/50V/X7R
33
33
MCU_3.3V
MCU_3.3V
MCU_3.3V
33
3333 R138
33
1K
R154 10K
NFC_INT
ADC_KEY2
ADC_KEY1
AMP_3.3V
PW_Det
C1041
R55 R54 R142
CHG_EN
AMP_MUTE
USB_FAULT
USB_EN
G_INT
Relay_EN
BM_update_EN
AUDIO_MUTE
Y_Rest
1000pF/50V/X7R
POWER_EN
POWER_EN1
3.3V_D2_EN
5V_D2_EN
MIC_DET
4.7K 4.7K 4.7K
I2C2_SDA R61 33
C27
C99
220uF/16V CE18
SAMP_SDA
I2C2_SCL R56 33
SAMP_SCL
BUSY
+
BUSY
R386
R385
10uF/16V/X5R
0.1uF/25V/X5R
1 BT_RX BT_RX1
1 STB_3.3V
2
2 3 BT_TX BT_TX1
3 4
10K
10K
4 5 R172 300 BT_LRCK GND1
5 6
6 7 R170 300 BT_BCLK BAT__Ctr
7 8
8 9 R171 300 BT_DATA MCU_3.3V
E
9 10 PW
10 11 BT_DP
11 BT_DP
12 BT_DM BT_DM
12 R243
13
13 14 BT_RESET NFC_11
14 15 BT_MFB 220K
15 D11
16
16 17 BT_RX Q2 2
17 18 BT_TX
18 19 NFC_BT C35 R38 10K 3
19 20 9 11 Q8 R244
C160
C162
C164
C165
C168
C169
C170
C207
C210
C213
NPN_3DG3904M
LRCK1 NPN_3DG3904M C34 12K
22 23 BT_LRCK 6 2Y2 2A2 14 R127 33 R158
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
12PF
12PF
12PF
100pF/50V/NP0
26 27 2 2Y0 2A0 18 R39
27 28 STAMINA GREEN_LED 1A0 1Y0
C125 10PF/50V/NPO
C114 10PF/50V/NPO
C130 10PF/50V/NPO
28 29 BT Blue_LED I2S_SEL1 1 20 FB50 500/800mA
29 OE1 VCC 3.3V_D1
30 AUX WHITE_LED I2S_SEL2 19 10
30 31 USB WHITE_LED OE2 GND 10K
31 32 POWER_ON_OFF
U27 C548
32
2
33 CHARGE ORANGE_LED 74LVC244 0.1UF
33 34 L WHITE_LED R591R589 D10
34 35 R WHITE_LED
C238
C237
C129
C126
C124
3
38
10PF/50V/NPO
10PF/50V/NPO
10PF/50V/NPO
10PF/50V/NPO
10PF/50V/NPO
POWER_KEY
38 39 Wireless WHITE_LED
39 3.3V_D1
40
40
F
41 POWER_KEY
41 42 ADC_KEY1
42 43 ADC_KEY2
43 44 NFC_INT0
GND
GND
44 45
45
C128
C131
C132
C134
C137
C138
C139
C143
C144
C146
C148
C149
C150
C155
C159
47
46
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
NC/100pF/50V/NP0
To BT Board
GTK-XB60
27 27
GTK-XB60
1 2 3 4 5 6 7 8 9
10uF/6.3V/X5R
0.1UF
C67 C172
10uF/6.3V/X5R 10uF/6.3V/X5R
Audio In_L Audio In_L1 R177 10K AUX_IN_L 5V_D1 1 14 AUX_IN_R
2 VREF VINR 13 AUX_IN_L
R320 4.7 OP_5V 3 AGND VINL 12
R124 FB6 4.7 4 VCC FMT 11
3.3V_D1 VDD MD1
13K/1% 5 10
10 MCLK5 R100 33 6 DGND MD0 9 R118 33 10
DATA0
R101 33 7 SCKI DOUT 8 R120 33
10 LRCK5 LRCK BCK BCLK5 10
C188 C187 C178 C190
CE10
+ U19
10uF/6.3V/X5R
NC/10uF/6.3V/X5R
0.1UF 0.1UF
PCM1808
220uF/16V
C93 C198
10uF/6.3V/X5R
Audio In_R Audio In_R1 R131 10K AUX_IN_R
10uF/6.3V/X5R
R119
13K/1%
R234 0
R238 0
C133
20K
100pF/50V/NP0 INR_OUT
C174
INR-
10uF/6.3V/X5R
R31
20K R197 20K
J1
R194 10K C135 100pF/50V/NP0 INL_OUT Audio In_L FB77 500/800mA 1
INR+
A_OUT_R 6 WH RD
C191 INL- R92 0
10uF/6.3V/X5R
Audio In_R FB78 500/800mA 2
Audio Out_L FB79 500/800mA 3
INL+
A_OUT_L 3.3V_D1 5
WH RD
U927
R189 Audio Out_R FB80 500/800mA 4
INR+ 1 14 INL+
RINP LINP 100K C61
1
R32 INR- 2 13 INL- R381 10uF/6.3V/X5R ESD3 ESD4 ESD5 ESD6 RCA/4h
RINN LINN INR_OUT Audio Out_R
NC/LVSL10180Z020/18V/2pF
NC/LVSL10180Z020/18V/2pF
NC/LVSL10180Z020/18V/2pF
NC/LVSL10180Z020/18V/2pF
20K 1.5K C197C171
INR_OUT 3 12 INL_OUT
OUTR OUTL
1000pF/50V/X7R
1000pF/50V/X7R
4 11 R195 30K R48 1K C62
SGND UVP 10uF/6.3V/X5R
INL_OUT Audio Out_L
2
AUDIO_MUTE R183 470 5 10 3.3V_D1
7 MUTE# PGND
6 9
PVSS PVDD
CE13 R192
7 8 C116 C173 +
R180 C117 CN CP 100K
C145
47K
0.1UF
10uF/6.3V/X5R
100uF/16V
0.1UF 1uF AS9632
C136 1uF
E
Party_Chain_In
VCC_4052
R233 R360
R303 100K
R83 0 1K
10K R364
R404 1M
R405 1M
R406 1M
R407 1M
NC/10K
R301 10K Q762 R343 S0: L-->nY0 R224 100
10K Vref
PNP_3CG3906M
S0: H-->nY1
R227 R361 C185
R312 22K R342 10K Q763 + CE11 100K
R15 C184 1K 1uF
R86 10K Q22 PNP_3CG3906M U25 100uF/16V
Party_Chain_Out 20K 0.1UF
NPN_3DG3904M Audio In_R1
Q23 C86 10uF/6.3V/X5R 12 16
R340 82K RTL X0 VCC
C87 10uF/6.3V/X5R 14
NPN_3DG3904M AOUT_R X1
R84 C175 R314 15 C83
R345 R26 20K X2
10K R313 6.8K C194 11 10uF/6.3V/X5R
2.2uF C177 22K R17 X3
15K R341 10uF 13
2.2uF Audio In_L1 20K X A_OUT_R
68K C89 10uF/6.3V/X5R 1
Audio Out_R C91 10uF/6.3V/X5R 5 Y0
R347 10K Q24 AOUT_L Y1
2 C85
NPN_3DG3904M R30 20K Y2
4 10uF/6.3V/X5R
Y3 3
Y A_OUT_L
C179 R348 R209 33 10
Audio In_R R315 56K R346 7 Party_Chain_SW A
10uF 10K 9
22K B
R338 68K
6
EN
F
R337 C176 R222 7 8
680K 10PF/50V/NPO 4.7K VEE GND
R339
RTL 470K 74HC4052
R354 C181
68K 2.2uF
R350 C180
R352 680K 10PF/50V/NPO
470K
GTK-XB60
28 28
GTK-XB60
1 2 3 4 5 6 7 8 9
3.3V_D1
1.8V
1.8V_D
C208 C140 C142 C204 C205 C141 C147
BCLK5
0.1UF 0.1UF 10uF/6.3V/X5R 0.1UF 0.1UF 0.1UF 10uF/6.3V/X5R
C202
NC/12PF
1.8V 3.3V
R256
NC/47K
24
23
22
21
20
19
18
17
B
OPEN2
GPIO11
DVDD18_1
OPEN1
DVSS3
TESTb
IRQ_N
DVSS2
3.3V_D1
11 16
VDD VEE 2
R572 10 14 CP
CVDD 25
DVSS4 16
C571 C572 C573 C574 C575 C576 SDA DSP_SDA
1uF/10V/X5R 1uF/10V/X5R 26
LRCK5 GPIO10 15
0.1UF 0.1UF Crystal
10uF/6.3V/X5R
10uF/6.3V/X5R
SCL DSP_SCL
1 27
CN DATA5
DATA4 28
GPIO9
U13 IOVDD1
14
TP61 TP64
3.3V R275 4.7K
GND
GPIO8
GND
3.3V_D1
3.3V 29
IOVDD2
YSS952 XOUT
13
Y2 24.576MHz/10PPM
R260
R573 10K 8 10 R574 470 AOUT_L 7
12 1 3
DIF AOUTL AOUT_L XIN
30 100
MCLK5 GPIO7 11
PLLVSS2
4
31 3.3V
C577 C199C200C201 1.8V DVDD18_2 C153 C154
10
C
470pF/50V/X7R PLLVSS1 R231 NC/47K 20pF/50V/NP0 20pF/50V/NP0
32
GPIO6
NC/12PF
NC/12PF
NC/12PF
9 R279 100
IC_N Y_Rest 7
33
AMUTE R575 4.7K 3 9 R576 470 AOUT_R GNDP R283
5 AMUTE SMUTE AOUTR AOUT_R 7 10K
AK4430
C579
PLLVDD
MCLK5 R122 33 4
DVSS1
MCLK 470pF/50V/X7R
GPIO5
GPIO4
GPIO3
GPIO2
GPIO1
GPIO0
BCLK5 R123 33 5
LRCK5 R125 33 7 BICK
DATA4 R126 33 6 LRCK
SDTI
8
12 13
15 VSS1 VREFH
VSS2
C581
U571
2.2UF
TSSOP16
DATA0
DATA6
DATA3
BCLK3
LRCK3
GND GND
1.8V
3.3V
Sample ADC
C239 C256
10uF/6.3V/X5R
0.1UF
R274 1K
180pF/50V/NP0
C261
5V_D1 1 14 Sample_ADC_INR
VREF VINR C270 4.7uF/10V/X5R
2 13 Sample_ADC_INL Sample Audio R286 33 BUSY
AGND VINL BUSY
E Sample IC
R292 4.7 3 12
DVDD3.3V
FB7 4.7 4 VCC FMT 11 R272 R285 33 SAMP_SDA
3.3V_D1 VDD MD1 SAMP_SDA
5 10
DGND MD0 10 R276 1K
10 MCLK5 R93 33 6 9 R115 33 DATA6 470 R284 33 SAMP_SCL
R112 33 7 SCKI DOUT 8 R116 33 U3 SAMP_SCL
C263
180pF/50V/NP0
C107 10PF/50V/NPO
C111 10PF/50V/NPO
C108 10PF/50V/NPO
10uF/6.3V/X5R
NC/10uF/6.3V/X5R
0.1UF 7 OSC1 PWM1 14
8 VPP_PAD AVDD1 13
9 PTB0 PWM2 12 DVDD3.3V
DVDD3.3V
10 VSS2 DVDD1 11
PTD0 PTD1
AM4KA340 SSOP
R277 0
R269 0
F
AMP_3.3V
U17
TGND
G
GND DVSS2_CORE PWM_M_4
14 43
AMP_3.3V AMP_3.3V DVDD2_CORE PWM_P_3
15 42
TP53 EMO_1 PWM_M_3
AMP_RST 16 41 R295 33
RESET PWM_P_2 OUT2A 12
TGND HP_SEL 17 40 R300 33
T_PDN 18 HP_SLE
PDN
PWM_M_2
PWM_P_1
39 R304 33
OUT2B
OUT1A
12 OUT2A/B : L
19 38 R305 33 12
7
5
AMP_MUTE
TAS_SDA TP55 20 MUTE PWM_M_1 37 R289 NC/2.2K
OUT1B 12 OUT1A/B : R
R288 R287 R268 TP57 21 SDA VALID 36 VALID 12
4.7K 4.7K 4.7K 5 TAS_SCL SCL DVSS1_CORE
R306 33 T_LRCLK 22 35
10 LRCK5 LRCLK DVDD1_CORE AMP_3.3V
R307 33 T_SCLK 23 34 R309 33 AMP_FAULT 5,12
10 BCLK5 R302 33 T_SDIN1 24 SCLK BKND_ERR 33
HP_SEL 10 DATA5 SDIN1 PSVC TP54
GND R311 10K 25 32 GND
R310 33 26 SDIN2 TEST 31
T_PDN 10 DATA7 SDIN3 LRCLKO R298
27 30 4.7K
28 SDIN4 SCLKO 29
5 AMP_RST VR_DIG SDOUT
AMP_RESET
AMP_3.3V
C226 C225
R293
C324 TAS5538
0.1UF 100K 0.1UF 10uF/6.3V/X5R
H GND
GTK-XB60
29 29
GTK-XB60
1 2 3 4 5 6 7 8 9
A CE31
+
CE30
+
R362
3.3
WL+ R773 220K
C291
NC/820uF/50V
470uF/50V R775 C530
0.1uF/50V
220K 10uF
C334
V_12V WL- R774 220K
10NF
R318 2.2
C290
R319 2.2 Q756 Q757
0.1uF/50V PNP_3CG3906M PNP_3CG3906M
C289
0.1uF/50V
L12 10uH/6A WL+
WR+ R776 220K
B
GVDD_B GVDD_A 0.1uF/50V 1000pF/50V/X7R
2 43 C268 0.033uF/50V/X7R C337 TL+
OTW BST_A
3 42 10NF
NC NC
Q758 Q759
4 41 C777 PNP_3CG3906M
NC PVDD_A PNP_3CG3906M
0.47uF/63V C338
AMP_FAULT 5 40
SD PVDD_A 10NF
C281 C280 R782
6 39 C284
OUT2A PWM_A OUT_A 100
0.1uF/50V 1000pF/50V/X7R
7 38 0.1uF/50V
RESET_AB GND_A R368
8 37 3.3
OUT2B PWM_B GND_B
R334 27K 9 36 L13 10uH/6A WL-
OC_ADJ OUT_B
10 35 R783 C769
GND PVDD_B C271 100K 0.22uF
11 34 C265 0.033uF/50V/X7R
AGND BST_B 0.1uF/50V
VALID 12 33 C267 0.033uF/50V/X7R L14 10uH/6A WR+ AMP_FAULT
VREG BST_C Q21
NPN_3DG3904M
C288 13 32
0.1uF/50V M3 PVDD_C C272
R366 C252
C
14 31
M2 OUT_C 3.3 2.7UF
15
M1 GND_C
30
0.1uF/50V C274 C276
DC detect
0.1uF/50V 1000pF/50V/X7R TR+
16 29 C336
OUT1A PWM_C GND_D
17 28 10NF
RESET_CD OUT_D
C776
18 27 0.47uF/63V
OUT1B PWM_D PVDD_D XP13
C339
19 26 C273 WL+ 4
NC PVDD_D 10NF WL- 3 4
V_12V C275 C278 3
20 25 0.1uF/50V WR+ 2
FB26 NC NC 2
1000pF/50V/X7R WR- 1
500/800mA 0.1uF/50V 1
21 24 C266 0.033uF/50V/X7R R372
VDD BST_D
3.3
C287 R333 2.2 22 23 4PIN/2.5mm
GVDD_C GVDD_D XP11
0.1uF/50V C286 C285 L15 10uH/6A WR- TL+
WL-
6
5 6 + TWL Upper left
5 -
V_12V
0.1uF/50V 0.1uF/50V
PW_MAIN WR-
TR+
S2
TR+
S1
4
3
2
1
4
3
2
+
-
Bottom left ET
1 + TWR Upper right
R384 NC/0
-
6PIN/2.5mm
D R331 2.2
CE32
+
CE29
+ C292
R380
3.3
NC/820uF/50V
470uF/50V
0.1uF/50V
C335
10NF
SW6
4 S1
4
C770 1000pF/50V/X7R
1 WR-
1
G-Sensor
E
C771 1000pF/50V/X7R
3 S2
3.3V_D1 3
C772 1000pF/50V/X7R
5 2
5 2 V_12V
C196
C50 C161 C773 C774
0.1UF
0.1UF
10uF/6.3V/X5R
16
15
14
0.01uF/50V/X7R
0.01uF/50V/X7R
U35 R136 G5LE-1
4.7K
NC5
NC4
VDD
1 13
2 VDD_IO NC3 12
NC1 GND2 D7 MBRX180/80V/1A
3 11
4 NC2 INT 10 G_INT
5 G_SCL SCL RES3
ADDR
5 9
RES1
GND1 RES2
SDA
KXCJK-1013
6
7
8
5 G_SDA Q6
R363 10K R77 10K
Relay_EN NPN_3DG3904M
F R60
47K
C323
0.1UF
GTK-XB60
30 30
GTK-XB60
1 2 3 4 5 6 7 8 9
D
1 8
C294
2 7
Connector Circuit
R323
CE2
1206
C277 3 6
+
R324
4 5
G
R273 U30 0.1uF
C102
1UF/35V/X5R
AP9561GM
4
3
2
1
S
100K
22uF/50V
G
NC/0
0.1uF AP9561GM C295
220K
NC/1UF/35V/X5R
D
5
6
7
8
BAT_EN
C92
R214
FB49 300
CE1
R322
0.1uF
+ C244 C257
220K
NC/0.1uF 1000pF/50V/X7R
22uF/50V
47K
U24
4
3
2
1
S
BAT__Ctr BAT__Ctr
PW BAT_EN G
U12
5
6
7
8
U16 AP9561GM
D
AP9467
S
D
1 8 D
8 1
5
6
7
8
2 7 D2 MBRX140/40V/1A
BAT_EN R218
7 2 R230 0.01
3 6
6 3 C235 0.1uF BAT
4 5
G
5 4
4
3
2
1
C233 0.1uF
G
C243 R253 AP9561GM
CE9 R247 R258 AP9561GM C120
+ U8
10
10 L3 6.8uH/3A R254 0.025 FB47 0 1
0.1uF 1
0.1uF 2
100K
3 2
1K
22uF/50V
C255 R261 4 3
5
6
7
8
C166 4
C293 10 AP9467 C253 NTC 5
NTC 6 5
R255
R221 CE14 CE16
C246 C234 6
7
1UF/35V/X5R
100pF/50V/NP0
33 NC/100pF/50V/NP0 + + C236
0.1uF C296 7
8
NC/1uF/50V/X7R 8
C247 0.1uF 0.1uF 9
0.1uF/50V/X7R 22uF/50V 9
10/5%
4
3
2
1
C262
22uF/50V
1UF/100V/X7R R104 XP3
330pF
U11 9PIN/2.0mm
NC/10
25
24
23
22
21
20
19
R257
POWERPD
VCC
/BATDRV
BTST
HIDRV
PH
LODRV
1K
C248
C
1UF/100V/X7R
1 18
ACN REGN R219 56K/1%
VREF
2 17 C105
MCU_3.3V ACP GND 0.1UF I limit=6A
3 16 R217 33K/1%
VREF R262 100K /ACDRV ACSET
CE Charge_EN 4 BQ24610 15 I per charge=0.15A C249
R237 100K CE ISET2 R208 120K/1% VREF
STAT1 STAT1 5 14 0.1uF/50V/X7R
STAT1 SRP
6 13
C158 TS SRN
R263
C259
C260
VREF R235 NC/100K 0.1UF
STAT2
ISET1
0.1uF/50V/X7R
VREF
TTC
VFB
/PG
0.1UF
15K/1%
NTC R220 VREF
10
11
12
30K/0.5% C245 TTC:5.6min/nF
MCU_3.3V R241 1M/0.5%
1uF/10V/X7R
C250
R149 R264
R259 R321 2.4K/0.5% NC/100K/0.5%
0.1UF
0 100K R229
I charge=1A/0.5A
D
10K/1%
/PG
STAT2
R242
PG
R226
R216
C264
R228 R225
R246
4.7K/1% 91K/0.5%
100K Q12 NC/47K/0.5%
STAT2
D
0.1UF
CHARGE STATE STAT1 STAT2 N_2SK3018
100K1%
18K/1%
MCU_3.3V G
R326
R325 C123
Charge in progress L H Charge Limit Voltage 16.386V
VREF
Charge complete H L
100K
0.1UF
1K
Charge_Current_CTL
standby charge 0.3C 1000mA
power on charge 0.15C 494mA
E
Charge_Current_CTL
per charge 0.05C 150mA
i linmit 0.5C 1500mA
charge voltage 4.15V*6 24.9V
GTK-XB60
31 31
GTK-XB60
4-12. PRINTED WIRING BOARD - NFC Board - • See page 22 for Circuit Boards Location. 4-14. PRINTED WIRING BOARD - BT Board - • See page 22 for Circuit Boards Location.
• : Uses unleaded solder. • : Uses unleaded solder.
1 2 1 2 3
NFC BOARD (COMPONENT SIDE) BT BOARD (COMPONENT SIDE)
A A
C
C BT BOARD (CONDUCTOR SIDE)
1 2 3 D
NFC BOARD
A NFC
TP63
U29
9
1 8
GND
VB VDDA
C10 C51 2 7
NC NC
3
4
15pF/50V/NP0
GND
GND
VSS NC 2
4 5
C79
1 2
Note: When replacing the BT board or the NFC board, be sure to
B
VA NIRQ 1uF/10V/X5R 1
2PIN/1.25mm
XP12 replace the BT board and the NFC board simultaneously.
MN63Y1214
TP62 The BT board or the NFC board cannot replace with single.
Among the repair parts, the BT board and the NFC board
are supplied as one unit.
GTK-XB60
32 32
GTK-XB60
1 2 3 4 5 6 7 8
BT BOARD
A BT
C26 U5
C309
0.1UF
C342 47pF/50V/NP0
C343 47pF/50V/NP0
C344 47pF/50V/NP0
C345 47pF/50V/NP0
C346 47pF/50V/NP0
C347 47pF/50V/NP0
C348 47pF/50V/NP0
C349 47pF/50V/NP0
51
50
49
C25 0.1uF/25V/X5R BT_BM63_Vina
XP35 C8 C7
10uF/10V/X7R P20 TM1
ANT3
ANT2
ANT1
45PIN/0.5mm
NC/15pF/50V/NP0
NC/15pF/50V/NP0
1 R1 0 BAT_IN TM2
1 2 STB_3.3V
1 48
2 3 BT_LRCK R2 33 2 DR0 GND 47 EAN TM3
3 4 BT_BCLK R3 33 3 RFS0 P05 46
4 5 FB36 300 BT_LRCK BT_DATA R4 33 4 SCLK0 P30 45 ADAP_IN TM4
5 6 5 DT0 P27 44 P20
6 7 STB_3.3V AOHPR P20
FB37 300 BT_BCLK C5 C27 C4 6 43 BT_RX TM5
7 8 AOHPM P02
R6
R7
7 42
8 9
NC/15pF/50V/NP0
AOHPL P31
NC/15pF/50V/NP0
NC/15pF/50V/NP0
FB38 300 BT_DATA R9 MIC_IN+ 8 41 BT_TX TM6
9 10 100K MIC_IN- 9 MICN1 P33 40
10 11 MICP1 P36
4.7K
4.7K
R8 0 BT_DP MIC_BIAS 10 39 BT_DP TM7
11 12 R10 BT_DM 11 MICBIAS DP 38 BT_DM
0
12 13 12 AIR DM 37 EAN P24 TM8
13 14 AIL EAN
B
R11 0 BT_RESET CP_SCL 13 36 TM9
14 15 R15 BT_MFB CP_SDA 14 P12 P03 35 TM10
0
15 16 BT_RESET R13 100 15 P13 P00 34
16 17 0 BT_RX 16 RST_N P35 33 CP_Reset
R12
17 18 R14 0 BT_TX P24 17 P01 P37 32
18 19 R18 0 NFC_BT NFC_BT 18 P24 GND 31
CODEC_VO
19 20 19 P04 LED1 30
SYS_PWR
AMB_DET
HCI_RXD
STB LED_5V C6
ADAP_IN
20 21 P15
HCI_TXD
R16 LED2
VDD_IO
0
BAT_IN
21 22 NC/0.1uF/25V/X5R
LED3
PWR
22 23
23 24
24 25 R157 PW_LED1
0
25 26
20
21
22
23
24
25
26
27
28
29
R158 0 PW_LED2
26 27
27 28 R162 0 STAMINA GREEN_LED
28 29
BT_RX
R172 0 BT Blue_LED BT_MFB
BT_TX
29 30 U2 STB_3.3V
R163 0 AUX WHITE_LED
ADAP_IN
30 31
VDD_IO
R164 0 USB WHITE_LED
31 32 BT_RESET R17 0 2 BAT_IN L1 120/2A
32 33 R165 CHARGE ORANGE_LED RST 3 BAT_IN
0
33 34 L WHITE_LED 1 VCC
C76
R166 0
C19
34 35 R167 R WHITE_LED GND
0 C18
C17
35 36 C12
R168 0 BASS RED_LED
36 37
15PF
0.1uF/16V/X7R
SGM803 22uF/6.3V/X5R
NC/10UF/6.3V/X5R
10UF/6.3V/X5R
37 38
38 39 R169 0 Wireless WHITE_LED
C
39 40
40 41 R178 0 POWER_KEY
41 42 R170 ADC_KEY11
0
42 43 R171 ADC_KEY21
0
43 44 R156 NFC_INT1
0
GND
GND
44 45
45 Apple Authentication
47
46
CP3V3
VDD_IO R23 0
Model:MIC
C20
2.2uF/10V/X5R Standardization:01U000MIC-POAT1
CP3V3
U3
C21
Authentication IC 2.0C MIC_IN+ C122 0.1UF R160 1K MIC_BIAS
0.1uF/25V/X5R
1 8
GND VCC C123
CP_SDA R174 33 2 7 R19 33 CP_Reset C118
SDA RST
2.2UF
15PF
3 6 R173 33 CP_SCL
D
NC SCL R159
C113
4 5
NC NC 9 R20 TP3 TM11 TM12
15PF
GND
2.2K
NC/0
GND
GND
2
1 FB49 500/800mA
1 STB LED_5V ESD3
2 C121 C119 C120
2
3
4
3 PW_LED1
3
15PF
15PF
15PF
4 PW_LED2
4 5 BT Blue_LED
NC/13-ESDPSA-V053
5 6 AUX WHITE_LED
6 7 USB WHITE_LED
7 8 CHARGE ORANGE_LED TP4
8 9
9 10 L WHITE_LED
10 11 R WHITE_LED
11 12 BASS RED_LED R161
12 0
13 Wireless WHITE_LED
E
13 14 STAMINA GREEN_LED
14 15
15 16 POWER_KEY GND_FIELD SIGNAL
16 17 ADC_KEY11
17 18 ADC_KEY21
18 19 NFC_INT1
19 20
20
XP10
GTK-XB60
33 33
GTK-XB60
4-16. PRINTED WIRING BOARD - KEY Board - • See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7
KEY BOARD (COMPONENT SIDE)
GTK-XB60
34 34
GTK-XB60
1 2 3 4 5 6 7 8 9
KEY BOARD
A
To BT Board
20 FB6 500/800mA 10mm
20 STB LED_5V
19 JMP3 SW1
19 18 PW_LED1 POWER_KEY
18
17
17
16
PW_LED2 WIRE JUMPER SW5 0V
R49 100
BT Blue_LED 10mm ADC_KEY11 Power ADC_KEY21
16 15 AUX WHITE_LED JMP5 7.5mm 17.5mm
15 14 USB WHITE_LED 12.5mm JMP22 JMP9 10mm ADD SPK
14 13 CHARGE ORANGE_LED JMP12 10mm JMP7 ESD7 C28 ESD15 C29 ESD9 C44
13 12
NC/EGA10603V05A1-B
NC/EGA10603V05A1-B
NC/EGA10603V05A1-B
JMP19 10mm JMP6 SW2 0V SW6
12 11 L WHITE_LED R54 100 0.99V R50 4.3K
47pF/50V/NP0
47pF/50V/NP0
47pF/50V/NP0
JMP21
11 10 R WHITE_LED 7.5mm 10mm
10 PLAY/Hand Free Wireless PARTY CHAIN/LIGHT
9 BASS RED_LED JMP4 JMP24
9 8 Wireless WHITE_LED 7.5mm 10mm
8 7 STAMINA GREEN_LED 7.5mm JMP8 SW7 1.48V
7 6 JMP11 7.5mm SW3 R56 8.2K
6 1.98V
5 17.5mm R827 0 POWER_KEY JMP14 R58 15K
5 EXTRA BASS
4 R823 0 ADC_KEY11 JMP2 7.5mm
4 3 Function/Paring
R825 0 ADC_KEY21 JMP15
B
3 2 R826 0 NFC_INT1 JMP1
2 1 SW4 SW8
1 2.47V 1.98V
R822 30K R70 15K
STAMINA/BATT
C307 0.1uF/50V/X7R
12.5mm VOL+
C327 NC/47pF/50V/NP0
C325 NC/47pF/50V/NP0
C361 NC/47pF/50V/NP0
C326 NC/47pF/50V/NP0
C323 NC/47pF/50V/NP0
C316 NC/47pF/50V/NP0
C319 NC/47pF/50V/NP0
C318 NC/47pF/50V/NP0
C320 NC/47pF/50V/NP0
C317 NC/47pF/50V/NP0
C322 NC/47pF/50V/NP0
20PIN/1.0mm
XP8 SW9
2.47V
R831 30K
VOL-
XS5
KEY*9
2 NFC_INT1
2 1
1
2PIN/2.0mm/100mm
C To NFC Board
R460 R461
R457 R456 R452
1.5K 1.5K R465
220 220 1K
330
LED3 LED4
PW_LED1 R52 4.7K Q17 Q14 R31 4.7K PW_LED2
BT LED2
AUX USB LED5
D
LED_WHITE LED_WHITE
LED_BULE
CHARGE LED_ORANGE
NPN_3DG3904M
NPN_3DG3904M
C35 C22
R30 R38
0.1uF/50V/X7R
0.1uF/50V/X7R
10K 10K
BT Blue_LED R27 4.7K Q10
AUX WHITE_LED R55 4.7K Q18 USB WHITE_LED R61 4.7K Q19
NPN_3DG3904M CHARGE ORANGE_LEDR48 4.7K Q30
NPN_3DG3904M NPN_3DG3904M
C32 C36 C39 NPN_3DG3904M
R36 R53 R60
C38
3
10K 10K
0.1uF/50V/X7R
10K
0.1uF/50V/X7R
0.1uF/50V/X7R
R47
LED1
0.1uF/50V/X7R
10K
PIN-1 GREEN
POWER PIN-3 RED
LED_3P_2PARTA
2
STB LED_5V
STB LED_5V STB LED_5V STB LED_5V
STB LED_5V
E
R462 R463 R458 R464 R468
330 330 560/5% 330 330
L LED6
LED_GREEN R LED7
LED_GREEN EXTRA BASS LED8
LED_RED Wireless PARTY CHAIN LED9
LED_GREEN
STAMINA
LED10
LED_GREEN
L WHITE_LED R65 4.7K Q20 R WHITE_LED R67 4.7K Q21 BASS RED_LED R57 4.7K Q29 Wireless WHITE_LED R69 4.7K Q22 STAMINA GREEN_LEDR63 4.7K Q31
NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M NPN_3DG3904M
C41 R64 C42 R66 C37 C43 R68 C40
R59 R62
10K 10K 10K
0.1uF/50V/X7R
0.1uF/50V/X7R
0.1uF/50V/X7R
0.1uF/50V/X7R
0.1uF/50V/X7R
10K 10K
F
LED*10
GTK-XB60
35 35
GTK-XB60
4-18. PRINTED WIRING BOARD - MIC KNOB Board - • See page 22 for Circuit Boards Location. 4-19. SCHEMATIC DIAGRAM - MIC KNOB Board -
• : Uses unleaded solder. 1 2 3 4 5 6
1 2
MIC KNOB BOARD (COMPONENT SIDE) MIC KNOB BOARD
A
A
RP1
Potentiometer 10K 10% WH09A-2H-B10K–F20
5
ESD6 1 3
NC/EGA10603V05A1-B Vertical
2
ESD8
NC/EGA10603V05A1-B
ESD10
NC/EGA10603V05A1-B XS1
KNOB1
KNOB2
KNOB3
5PIN/2.0mm/80mm
KNOB2 1
2 1
R832 R828 STB_5V FB5 500/800mA 3 2
Wired PARTY CHAIN 4 3
Wired Blue_LED 5 4
5.6K/1% 0 5
C324 47pF/50V/NP0
C328 47pF/50V/NP0
To MAIN Board
C4 0.1uF/50V/X7R
STB_5V
MIC KNOB
C321 47pF/50V/NP0
ESD11
NC/EGA10603V05A1-B
MIC KNOB BOARD (CONDUCTOR SIDE)
C
Wired BUTTON
C STB_5V
D R466
220
LED13
Wired PARTY CHAIN LED_GREEN
0.1uF/50V/X7R
10K
E Wired LED
GTK-XB60
36 36
GTK-XB60
4-20. PRINTED WIRING BOARD - TOP SPEAKER Board - • See page 22 for Circuit Boards Location. 4-22. PRINTED WIRING BOARD - BOTTOM SPEAKER Board - • See page 22 for Circuit Boards Location.
• : Uses unleaded solder. • : Uses unleaded solder.
1 2 3 1 2 3
TOP SPEAKER BOARD TOP SPEAKER BOARD BOTTOM SPEAKER BOARD BOTTOM SPEAKER BOARD
(COMPONENT SIDE) (CONDUCTOR SIDE) (COMPONENT SIDE) (CONDUCTOR SIDE)
A A
B B
4-21. SCHEMATIC DIAGRAM - TOP SPEAKER Board - 4-23. SCHEMATIC DIAGRAM - BOTTOM SPEAKER Board -
1 2 1 2 3
LED14
LED_WHITE LED15
LED_WHITE
2
1
2
1
2
1
B B
2
1
XS3
2PIN/2.0mm/40mm XS4
2PIN/2.0mm/40mm
GTK-XB60
37 37
GTK-XB60
4-24. PRINTED WIRING BOARD - TOP LED Board - 4-25. SCHEMATIC DIAGRAM - TOP LED Board -
• See page 22 for Circuit Boards Location.
1 2 3 4 5 6 7 8
• : Uses unleaded solder.
1 2 3
TOP LED BOARD (COMPONENT SIDE) TOP LED BOARD
A 5V_D5
A 5V_D5
5V_D5
C31 C34 C33
0.1uF/16V/X7R
10uF/10V/X7R
10uF/10V/X7R
1
LED26
To LED Board
1
LED18
XP14
R532 R556 0
R527 GND_E 2
PWM12_R PWM7_R R553 0 1 2
PWM8_R 1
2
GREEN RED BLUE GREEN
2
RED BLUE R535
200 120 2PIN/2.0mm
200
C146
NC/0.1UF C149
NC/0.1UF
C154
NC/0.1UF
GND_E
GND_E
B
B PWM8_B
R562
R595
GND_E
200
PWM12_B
C147
NC/0.1UF GND_E
25
200
5V_D5
7 FB19 220 PWM7_B
GND2
OUT1 8 FB20 220 PWM7_G
GND_E 3 OUT2 9 FB21 0 PWM7_R
C150 VCC OUT3
NC/0.1UF CE9
0.1uF/16V/X7R
C29C23
R560 + 10 FB22 0 PWM8_B
R176 OUT4 11 FB23 0 PWM8_G
1uF/10V/X7R
GND_E R175 OUT5 12
100uF/16V/SMD
FB24 0 PWM8_R
4.7K OUT6
4.7K
TOP LED BOARD (CONDUCTOR SIDE)
5V_D5
150 13 FB25 220 PWM9_B
OUT7
R68 100 GND_E OUT8
14 FB26 220 PWM9_G
To MAIN Board
C PWM8_G
LED-SDA1
LED-SCK1
100
5
6 SDA
SCL
OUT9
15
16
FB27
FB28
220
220
PWM9_R
PWM10_B
R69 OUT10
C351 47pF/50V/NP0
C350 47pF/50V/NP0
LED_SHDNN1 24 17 FB30 220 PWM10_G
C148 SDB OUT11 XP7
18 FB31 220 PWM10_R
R561 OUT12 12
0.1uF/16V/X7R
C24
NC/0.1UF
R177 12
C
PWM12_G 2 19 11 FB29 70/3A
100K R-EXT OUT13 11
20 10 C65
R272 OUT14 10 1000pF/50V/X7R
4 21 9
150 GND U18 OUT15 9 8 FB45 70/3A
C151 8 GND_E
GND_E 22 FB39 0 PWM12_B 7
GND_E OUT16 23 FB40 0 PWM12_G 7 6 FB32 500/200mA LED-SDA1
NC/0.1UF
5.1K/1% OUT17 6
GND_E 1 FB41 0 PWM12_R 5 FB33 500/200mA LED-SCK1
OUT18 5 4 FB34 500/200mA LED_SHDNN1
GND_E 4 3 FB35 500/200mA WHITE_LED2
3 2
31FL3218 2 1
GND_E 1
12PIN/1.0mm
5V_D5
12
11
D
10 FB57 70/3A
GND
GND
10 9 PWM9_R
9 8 PWM9_G
8 7 PWM9_B
7 6 PWM10_R
6 5 PWM10_G
5 4 PWM10_B
4 3 PWM7_G
3 2 PWM7_B
2 1 70/3A
1
FB58 GND_E
XP16
10PIN/1.25mm
E R461
5V_D5
LED
150
LED16
LED_WHITE
1000pF/50V/X7R
GND_E
GTK-XB60
38 38
GTK-XB60
4-26. PRINTED WIRING BOARD - BOTTOM LED Board - 4-27. SCHEMATIC DIAGRAM - BOTTOM LED Board -
• See page 22 for Circuit Boards Location.
1 2 3 4 5 6
• : Uses unleaded solder.
1 2 3
BOTTOM LED BOARD (COMPONENT SIDE) BOTTOM LED BOARD
A 5V_D4
5V_D4 5V_D4
1
A
LED7
1
LED8
R511
R512
9_R
2
RED BLUE GREEN 10_R XP18
2
R524 R545 0
200 RED BLUE GREEN 2
120 2
200 7_G R550 0 1
C139 1
C136
NC/0.1UF
NC/0.1UF
2PIN/2.0mm
C142
NC/0.1UF
B To UP LED Board
B 9_B
R510
5V_D4
R514
11
12
200 10_B
CE11
C137 C28 C30 C32 FB59 70/3A 10
GND
GND
+ 9_R 9 10
NC/0.1UF 200
NC/100uF/16V/SMD
0.1uF/16V/X7R
10uF/10V/X7R 10uF/10V/X7R 9
C140 9_G 8
9_B 7 8
6 7
NC/0.1UF
10_R
10_G 5 6
10_B 4 5
7_G 3 4
XP12
C R509
10PIN/1.25mm
5V_D4
9_G
150
R513 LED
10_G
LED10
LED_WHITE
C
150
C138 C141 R460
7_B
NC/0.1UF
NC/0.1UF
150
C145
NC/0.1UF
D
GTK-XB60
39 39
GTK-XB60
1 2 3 4 5 6 7 8 9
POWER BOARD
A R534
0
R535
0
CY503
470pF/250VAC
C508
D505 HER203
+ 1
1 20A/300V
R502 2
B 28V/23V
2 3 + +
C501 R505 R506 3
103/400V T501
150uF/250V 47K/2W PQ32 R536
4 -
150uF/450V 28MV 28V NC/0
22 22 VDD1 8VOUT
VDD A8 LIF551 XP1
9 XP2 28MV 7
A9 C510 C518 6
28MV 6 28V/23V
FB504 28V 28V/23V
NC/0.1uF/50V/X7R 5 5
4 28V 4 28V/23V
R503 2 C509 3 28V 3 GND
+ +
FB90@100MHz N.C CE506 CE508 0.1uF/50V/X7R 0.1uF/50V/X7R 2 GND 2 GND
1 GND 1
PSON GND
LIF503 820uF/50V 820uF/50V GND PSON
B3 2 A A 2 3 B 250uH
33K D502 10 R537
10 7PIN/2.0mm/120mm
LIF502-1 FR207/2A/1000V NC/0
D 3 11
V-GND OP-
R570 OP+
10m GND_EARTH 6PIN/2.0mm
C 4 1 N C 4 1 D A11 GND
R504 12
24mH LIF502 24mH A12
LIF4-22-15
R597
4 R515 ZD504
4
CX501 0.22uF/250VAC 33K M7J/1A/1000V 15V
NC/1A/1000V R596 NC/0
D535
0
N D534
C
2M R5014 2M R5013 VCC R514 0 0 FB 6 FB
2M R5012 2M R5011 CE504
+ R518
2K
TR501 47uF/50V
NTC/3ohm/5A CE503 5
P-GND PSON
CY502 P-GND
+ ZD505
CY501 ZD509 R522
47uF/50V BZX79C18 56.2K R539
220pF/250VAC 15V C517 33 LM3580
220pF/250VAC U506A
R532 NC/0.1uF 8
<Package>
D506
30UH U502 OP+R527 NC/2.7K 3 V+
+
2 1 R528 1 1 R530
1
220K R517 OP- NC/2.2K 2 3 OPP
- V- 2
R507 LTV-817S-B 4.7K CE541 + NC/2.4K/1%
3 4 D503 22 R529 4 NC/120K
Q501
C515 NC/BAT54C
2
8
5
LIF501 C511 100pF/50V/NP0 C514
D
C506 BAS316 R508 10uF/16V C516
HV
NC
VCC
OUT
47 12N65 NC/0.1uF NC/2200pF NC/0.1uF
G
2
S
RV501 VDR/620V R509
U501 C507 R519 10K C512 0.1uF/50V/X7R
NCP1271 1 OPP
D
0.1uF/50V/X7R 10pF/1KV U551
COMP
F501 10K PSON
GND
3
FUSE_3.15AL/250V AS431 R521
CS
RT
R520 12K
Skip/Latch 10K/1% R525 R526 10K/1%
4
CN501
R510 1.5K 68K
100pF/50V/NP0
C504
2 1 R538 NPN_3DG3904M
L N C503 R513 C505 0 Q510
R511 R533
PWR JACK 0.01uF C529
TR506 C528 0.1uF/50V/X7R 10K/1%
1nF 0.2R ZD503
12K U503 BZX79C27 100K
VCC 0.1uF/50V/X7R
1
C513
R531
R512 100 NC/LTV-817S-B NC/0.1uF
Skip/Latch
2
R516 NC/100
R524 0
NC/1K
E
HS1 HS2
OP-
GTK-XB60
40 40
GTK-XB60
4-29. PRINTED WIRING BOARD - POWER Board (US and CND models) -
• See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6
POWER BOARD (COMPONENT SIDE)
41
GTK-XB60
4-30. PRINTED WIRING BOARD - POWER Board (Except US and CND models) -
• See page 22 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6
POWER BOARD (COMPONENT SIDE)
42
GTK-XB60
SECTION 5
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • The mechanical parts with no reference • Refer to “COLOR VARIATIONS” on page 5
they may have some difference from the number in the exploded views are not sup- about color variation of the unit.
original one. plied.
• Items marked “*” are not stocked since • Color Indication of Appearance Parts Ex-
they are seldom required for routine ser- ample:
vice. Some delay should be anticipated KNOB, BALANCE (WHITE) . . . (RED)
when ordering these items.
Parts Color Cabinet’s Color
right side 7
6 2
10
5 6 2 10 9
A
6 2
BAT1
2 2 8
2 A
2
2
2
2 2
3 2
2 4
6
6
6
rear side speaker cabinet section
left side
2
2
2
Note: CUSHION (BATTERY CABLE) (Ref. No. 9) and CUSHION
(BATTERY) (Ref. No. 10) cannot be reused. When replacing
2 1
the LITHIUM ION BATTERY (Ref. No. BAT1), be sure to re- 2
place them with new parts simultaneously.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 9-885-219-47 RUBBER (BLACK 4PCS) (4 pieces, 1 set) 4 9-885-219-34 SIDE PANEL R (CEL RED) (for R-ch)
(for Black) (Including Inside rubber) (for Orange Red)
1 9-885-219-48 RUBBER (BLUE 4PCS) (4 pieces, 1 set) (for Blue) 5 9-885-219-41 FOOT PAD (CIRCLE BLACK 4PCS)
1 9-885-219-49 RUBBER (RED 4PCS) (4 pieces, 1 set) (4 pieces, 1 set) (for Black)
(for Orange Red) 5 9-885-219-42 FOOT PAD (CIRCLE BLUE 4PCS) (4 pieces, 1 set)
2 9-885-219-01 SCREW (M4X20) (for Blue)
3 9-885-219-35 SIDE PANEL L (UC2 BLACK) (for L-ch) (Including 5 9-885-219-43 FOOT PAD (CIRCLE RED 4PCS) (4 pieces, 1 set)
Inside cushion, Inside rubber) (for Black) (US, CND) (for Orange Red)
3 9-885-219-38 SIDE PANEL L (CEL BLACK) (for L-ch) 6 9-885-219-02 SCREW (M3X10)
(Including Inside cushion, Inside rubber) 7 9-885-219-91 BATTERY BOX (UC2) (Including Inside cushion)
(for Black) (AEP, RU, UK, AUS) (US, CND)
3 9-885-219-39 SIDE PANEL L (CEL BLUE) (for L-ch) 7 9-885-219-92 BATTERY BOX (CEL) (Including Inside cushion)
(Including Inside cushion, Inside rubber) (for Blue) (Except US, CND)
3 9-885-219-40 SIDE PANEL L (CEL RED) (for L-ch) (Including 8 9-885-219-93 BATTERY COVER (UC2) (Including Inside cushion)
Inside cushion, Inside rubber) (for Orange Red) (US, CND)
4 9-885-219-29 SIDE PANEL R (UC2 BLACK) (for R-ch) 8 9-885-219-94 BATTERY COVER (CEL) (Including Inside cushion)
(Including Inside rubber) (for Black) (US, CND) (Except US, CND)
4 9-885-219-32 SIDE PANEL R (CEL BLACK) (for R-ch) (Including
Inside rubber) (for Black) (AEP, RU, UK, AUS) 9 9-885-221-60 CUSHION (BATTERY CABLE) (See Note)
10 9-885-221-59 CUSHION (BATTERY) (See Note)
4 9-885-219-33 SIDE PANEL R (CEL BLUE) (for R-ch) BAT1 1-853-678-11 LITHIUM ION BATTERY (LIP4160HEPC (SY6))
(Including Inside rubber) (for Blue)
43
GTK-XB60
52
B D
C 52
52
board section
52
D
B
C
52 52
52 SP2
not supplied
52
52 52
52
52
52 SP1
52
53
52
52
53 52
52
51
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 9-885-219-44 FOOT PAD (FLAT BLACK 4PCS) (4 pieces, 1 set) 54 9-885-219-26 BOTTOM PANEL (ALL BLACK) ASSY
(for Black) (Including Handle bracket, Cushion) (for Black)
51 9-885-219-45 FOOT PAD (FLAT BLUE 4PCS) (4 pieces, 1 set) 54 9-885-219-27 BOTTOM PANEL (ALL BLUE) ASSY
(for Blue) (Including Handle bracket, Cushion) (for Blue)
51 9-885-219-46 FOOT PAD (FLAT RED 4PCS) (4 pieces, 1 set) 54 9-885-219-28 BOTTOM PANEL (ALL RED) ASSY (Including
(for Orange Red) Handle bracket, Cushion) (for Orange Red)
52 9-885-219-01 SCREW (M4X20) SP1 9-885-219-04 SPEAKER UNIT (WF) (Woofer: Bottom)
53 9-885-219-02 SCREW (M3X10) SP2 9-885-219-04 SPEAKER UNIT (WF) (Woofer: Top)
44
GTK-XB60
103
103 104
103
G
103 103
103
103
103
103 103
103
103 102
103
E
not supplied
F rear side
NFC board
101
BT board
G
not supplied F
FFC2
FFC1 E
TOP1
front side
Note: When replacing the BT board or the NFC board, be sure to re-
place the BT board and the NFC board simultaneously. The BT
board or the NFC board cannot replace with single. Among the
repair parts, the BT board and the NFC board are supplied as one
unit.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 9-885-218-86 BT + NFC BOARD, COMPLETE (for Black) FFC1 9-885-219-06 FFC (BT-MAIN) (45 CORE)
(See Note) FFC2 9-885-219-07 FFC (BT-KEY) (20 CORE)
101 9-885-218-87 BT + NFC BOARD, COMPLETE (for Blue)
(See Note) TOP1 9-885-219-23 TOP PANEL (ALL BLACK) ASSY
101 9-885-218-88 BT + NFC BOARD, COMPLETE (for Orange Red) (Including Microphone, Button, Lens, Cushion)
(See Note) (for Black)
102 9-885-218-91 KEY BOARD, COMPLETE (Including Cushion) TOP1 9-885-219-24 TOP PANEL (ALL BLUE) ASSY
103 9-885-219-02 SCREW (M3X10) (Including Microphone, Button, Lens, Cushion)
(for Blue)
104 9-885-219-50 TOP HANDLE (BLACK) (Including Cushion) TOP1 9-885-219-25 TOP PANEL (ALL RED) ASSY
(for Black) (Including Microphone, Button, Lens, Cushion)
104 9-885-219-51 TOP HANDLE (BLUE) (Including Cushion) (for Orange Red)
(for Blue)
104 9-885-219-52 TOP HANDLE (RED) (Including Cushion)
(for Orange Red)
45
GTK-XB60
not supplied
not supplied
155
153
153
151
151
151
I
151
153 153
154
153
156 153
153
H 151
I
H
152
151 151
not supplied
151
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 9-885-219-03 SCREW (3X6) 154 9-885-218-81 MAIN BOARD, COMPLETE (Including Heat sink)
152 9-885-218-84 POWER BOARD, COMPLETE (US, CND)
152 9-885-218-85 POWER BOARD, COMPLETE (Except US, CND) 155 9-885-218-92 MIC KNOB BOARD, COMPLETE
153 9-885-219-02 SCREW (M3X10) 156 9-885-219-00 THERMAL SHEET
46
GTK-XB60
206
front side
rear side
not supplied
FFC3
205
202
SP3
202
202
202 204 SP4
202
202
bottom side
not supplied
203
202
202 201
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 9-885-218-94 BOTTOM LED BOARD, COMPLETE 206 9-885-219-21 FRONT PANEL (CEL BLUE) ASSY
202 9-885-219-02 SCREW (M3X10) (Including Grill, Lens, Lighting tube, Cushion)
203 9-885-218-96 BOTTOM SPEAKER BOARD, COMPLETE (for Blue)
(Including Cushion) 206 9-885-219-22 FRONT PANEL (CEL RED) ASSY
204 9-885-218-95 TOP SPEAKER BOARD, COMPLETE (Including Grill, Lens, Lighting tube, Cushion)
(Including Cushion) (for Orange Red)
205 9-885-218-93 TOP LED BOARD, COMPLETE FFC3 9-885-219-12 FFC (TOP LED-MAIN) (12 CORE)
206 9-885-219-17 FRONT PANEL (UC2 BLACK) ASSY SP3 9-885-219-05 SPEAKER UNIT (TW) (Tweeter: Right)
(Including Grill, Lens, Lighting tube, Cushion) SP4 9-885-219-05 SPEAKER UNIT (TW) (Tweeter: Left)
(for Black) (US, CND)
206 9-885-219-20 FRONT PANEL (CEL BLACK) ASSY
(Including Grill, Lens, Lighting tube, Cushion)
(for Black) (AEP, RU, UK, AUS)
47
GTK-XB60
SECTION 6
BOTTOM LED
ELECTRICAL PARTS LIST
BOTTOM SPEAKER BT + NFC
KEY MAIN MIC KNOB • RESISTORS The components identified by mark 0
All resistors are in ohms. or dotted line with mark 0 are critical for
POWER TOP LED METAL: Metal-film resistor. safety.
METAL OXIDE: Metal oxide-film resistor. Replace only with part number specified.
TOP SPEAKER F: nonflammable
Note: • CAPACITORS Les composants identifiés par une marque
• Due to standardization, replacements in uF: μF 0 sont critiques pour la sécurité.
the parts list may be different from the • COILS Ne les remplacer que par une pièce por-
parts specified in the diagrams or the com- uH: μH tant le numéro spécifié.
ponents used on the set. • SEMICONDUCTORS
• -XX and -X mean standardized parts, so In each case, u: μ, for example: Among mounted electrical parts on each
they may have some difference from the uA. . : μA. . , uPA. . , μPA. . , board, only parts that are described in the
original one. uPB. . : μPB. . , uPC. . , μPC. . , electrical parts list can be replaced for re-
• Items marked “*” are not stocked since uPD. . : μPD. . pairing.
they are seldom required for routine ser- The parts that are not described in the
When indicating parts by reference num- electrical parts list cannot be replaced with
vice. Some delay should be anticipated
ber, please include the board name. single for repairing.
when ordering these items.
In that case, replace the complete mount-
ed board.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
9-885-218-94 BOTTOM LED BOARD, COMPLETE 9-885-218-92 MIC KNOB BOARD, COMPLETE
*************************** ************************
************************************************************* *************************************************************
9-885-218-96 BOTTOM SPEAKER BOARD, COMPLETE 9-885-218-84 POWER BOARD, COMPLETE (US, CND)
******************************* 9-885-218-85 POWER BOARD, COMPLETE (Except US, CND)
**********************
*************************************************************
< AC INLET >
9-885-218-86 BT + NFC BOARD, COMPLETE (for Black)
(See Note) 0 CN501 9-885-218-97 AC INLET (- AC IN)
9-885-218-87 BT + NFC BOARD, COMPLETE (for Blue) *************************************************************
(See Note)
9-885-218-88 BT + NFC BOARD, COMPLETE (for Orange Red) 9-885-218-93 TOP LED BOARD, COMPLETE
(See Note) ***********************
***********************
*************************************************************
*************************************************************
9-885-218-95 TOP SPEAKER BOARD, COMPLETE
9-885-218-91 KEY BOARD, COMPLETE ****************************
*******************
*************************************************************
< SWITCH >
MISCELLANEOUS
SW1 9-885-218-99 TACT SW (1) **************
SW2 9-885-218-99 TACT SW ( u)
SW3 9-885-218-99 TACT SW (FUNCTION PAIRING) BAT1 1-853-678-11 LITHIUM ION BATTERY (LIP4160HEPC (SY6))
SW4 9-885-218-99 TACT SW (STAMINA BATTERY) FFC1 9-885-219-06 FFC (BT-MAIN) (45 CORE)
SW5 9-885-218-99 TACT SW (ADD) FFC2 9-885-219-07 FFC (BT-KEY) (20 CORE)
FFC3 9-885-219-12 FFC (TOP LED-MAIN) (12 CORE)
SW6 9-885-218-99 TACT SW (W.PARTYCHAIN LIGHT) SP1 9-885-219-04 SPEAKER UNIT (WF) (Woofer: Bottom)
SW7 9-885-218-99 TACT SW (EXTRA BASS)
SW8 9-885-218-99 TACT SW (+) SP2 9-885-219-04 SPEAKER UNIT (WF) (Woofer: Top)
SW9 9-885-218-99 TACT SW (−) SP3 9-885-219-05 SPEAKER UNIT (TW) (Tweeter: Right)
************************************************************* SP4 9-885-219-05 SPEAKER UNIT (TW) (Tweeter: Left)
TOP1 9-885-219-23 TOP PANEL (ALL BLACK) ASSY
9-885-218-81 MAIN BOARD, COMPLETE (Including Heat sink) (Including Microphone, Button, Lens, Cushion)
******************** (for Black)
TOP1 9-885-219-24 TOP PANEL (ALL BLUE) ASSY
< DIODE > (Including Microphone, Button, Lens, Cushion)
(for Blue)
D1 9-885-218-48 SS34/40V/3A
D9 9-885-218-48 SS34/40V/3A TOP1 9-885-219-25
TOP PANEL (ALL RED) ASSY
(Including Microphone, Button, Lens, Cushion)
< IC > (for Orange Red)
*************************************************************
U15 9-885-220-40 CONVERTER, DCDC
U21 9-885-220-40 CONVERTER, DCDC – Continued on next page –
*************************************************************
Note: When replacing the BT board or the NFC board, be sure to replace
the BT board and the NFC board simultaneously.
The BT board or the NFC board cannot replace with single.
Among the repair parts, the BT board and the NFC board are sup-
plied as one unit.
48
GTK-XB60
501
49
GTK-XB60
REVISION HISTORY