Professional Documents
Culture Documents
Lean Implementation in Indian Process Industries - Some Empirical Evidence
Lean Implementation in Indian Process Industries - Some Empirical Evidence
www.emeraldinsight.com/1741-038X.htm
Abstract
Purpose – In the present era of intense competition, industries are adopting lean manufacturing for
successful survival. The concept of lean manufacturing is new for Indian process industries. The
purpose of this paper is to investigate the status of lean manufacturing in Indian process industries in
terms of lean practices, reasons and challenges of implementing lean manufacturing.
Design/methodology/approach – A survey was carried out to assess the level of lean
implementation in Indian process industries. Statistical tests were conducted to assess the significant
lean practices, reasons and challenges of implementing lean in Indian process industries.
Findings – It is observed that the level of implementation of lean manufacturing in Indian process
industries is still low. Results indicate that Indian process industries those who have implemented lean
found lean to be very useful to reduce wastes and to increase quality. Major lean practices being
implemented by Indian process industries are primarily those which are related to waste elimination or
improvement in quality. Indian process industries found that important challenges to implement lean
are to produce in small batches, to arrange for lean experts and to impart training to employees.
Research limitations/implications – In the present study, the sample size is small and hence, the
findings should be generalized cautiously. Although the study indicates that lean can be very useful if
implemented in Indian process industries but further empirical studies are required to quantify
performance improvements through adoption of lean.
Originality/value – The paper explores status of lean adoption in Indian process industries.
Considering the unique characteristics of process industries, the present research would be helpful for
making strategies to implement lean in process industry setups.
Keywords India, Lean manufacturing, Performance improvement, Process industry
Paper type Research paper
1. Introduction
In the present era of fierce competition, manufacturing organizations relentlessly make
efforts to improve their performance for successful survival (Hokoma et al., 2008).
According to Ghosh (2013), Indian manufacturing companies are also feeling the heat
of competition after the introduction of open market policies and industrial
Journal of Manufacturing
liberalization. Competition has intensified in all sectors whether it is service sector, Technology Management
discrete manufacturing or process manufacturing. Upadhye et al. (2010) underline Vol. 26 No. 1, 2015
pp. 131-160
that intense competition has motivated Indian manufacturing organizations to search © Emerald Group Publishing Limited
1741-038X
methods to reduce cost and to deliver on time with high customer satisfaction. DOI 10.1108/JMTM-05-2013-0049
JMTM Dangayach and Deshmukh (2003) measured the competitiveness of manufacturing
26,1 industries of India and found that the process sector showed least competitiveness on
competitive priorities such as quality, cost, delivery, innovation and flexibility.
As a result, it seems to be imperative for process sector of India to search for new
business strategies, not only to outperform their competitors but also to combat
other market challenges. One possible solution is to adopt a suitable world class
132 manufacturing methodology such as “lean,” which is considered to be immensely
successful to improve overall performance of an organization (Upadhye et al., 2010).
Adoption of “lean” in discrete manufacturing is widespread. In-fact, its success in
discrete manufacturing has motivated other industries too to endeavor lean
(Garza-Reyes et al., 2012). However, in process industries lean methodology is not
common (Gebauer et al., 2009). Barely any literature is available about lean
implementation in process industries (Abdulmalek and Rajgopal, 2007). Moreover,
managers still feel scepticism about the validity of lean manufacturing in process
industry environment (Melton, 2005).
According to King (2009), the implementation of lean manufacturing is not straight
forward in process industries due to typical operational characteristics. For example,
process industries have continuous flow of material, very large, inflexible and fixed
capacity equipments, process dependence on time and temperature, and high volumes
with less variety of products (Crama et al., 2001). With such constraints it is a big
challenge to implement numerous lean practices in process industries such as “pull
production,” kanban, “setup reduction” and “cellular manufacturing,” which were
originally devised for discrete industries. Therefore, it is interesting to investigate
that a philosophy which was evolved and developed in discrete manufacturing, up-to
what extent it is applicable in process industries.
Moreover, according to Ghosh (2013), adoption of lean manufacturing in India has
been started very recently. Hence, the status of lean implementation in India is
still ambiguous (Garza-Reyes et al., 2012). Therefore, it is uncertain whether
process industries in India are enthusiastic about implementation of lean, or not.
Comprehensive literature search confirms that till now no attempt has been made to
investigate the status of lean manufacturing in Indian process industries. This study is
the first attempt to fill this gap in research and will examine various aspects of
implementation of lean manufacturing in process sector of India.
Primary concern of the present study is to investigate whether Indian process
industries think lean is useful. It will also be discovered if Indian process industries
actually have started implementing lean. Subsequently, we will try to find out reasons
of adoption of lean in Indian process industries. It will not only help to guide the use of
lean tools but will also help to decide the target values of benefits perceived by process
industries. In conjunction with reasons of adoption, it is also important to identify the
challenges to implement lean. Otherwise, the implementation exercises may go in vain.
Lean implementation can be highly successful if the challenges to implement lean are
dealt carefully. Finally, it is important to analyze that while lean is proved to be
powerful tool to eliminate wastes and to improve performance, why process industries
hesitate to adopt it?
In the present paper we carried out a survey to address the above mentioned issues
related to lean manufacturing implementation in Indian process industries. The paper
is organized as follows. Section 2 deals with literature review. Studies focussed around
lean implementation issues, and characteristics of process industries are discussed in
this section. Research methodology and the observations of the study are presented
in Sections 3 and 4, respectively. Section 5 presents results of the study and important Lean
insights. Lastly, in Section 6, conclusions drawn and directions for future research implementation
are discussed.
Mady (1991) 44 manufacturing Effect of type of industry on Inventory represents 24 percent of total assets in process
enterprises in Egypt inventory control industries. Techniques such as MRP, JIT, Kanban, and zero
including textile, food and inventory are useful for inventory management
chemical companies
White (1993) 494 US manufacturing firms Benefits of JIT 90 percent gained benefits from implementing JIT. JIT is helpful in
including large portion of implementation reducing lead time, decreasing throughput time, improving
process industries production quality, increasing productivity and enhancing
customer responsiveness
Sohal and Egglestone 51 Australian industries Status of lean 82 percent industries were practicing lean manufacturing.
(1994) including 69 percent implementation Substantial benefits can be achieved through implementation of
industries from process lean manufacturing despite of type or size of industry
sector
Besson and Haddadj 50 US chemical firms Effect of employees’ skill on Successful implementation of lean manufacturing needs elevation
(1999) lean adoption in employees’ skills
Gyampah and Gargeya 48 manufacturing firms in Status of JIT Same fundamental understanding of JIT as in developed countries.
(2001) Ghana (most of the firms are implementation JIT manufacturing firms give emphasis on employees’ training,
from process sector) cellular manufacturing, setup time reduction, continuous quality
improvement and supplier relationship
Soriano-Meier and Survey of 30 UK ceramics Factors affecting JIT Lean production’s effects can only be seen in long term. There
Forrester (2002) industries implementation exists strong relationship between managerial commitment and JIT
implementation
White and Prybutok 494 US manufacturing firms Comparison of JIT practices Repetitive process industries have higher utilization of JIT
(2001) (including continuous flow implementation practices in comparison with non repetitive industries like job or
industries) batch production
Shah and Ward (2003) 1748 US manufacturing Investigation of lean Lean implementation depends on plant age and size but not on
firms practices implementation type. JIT practices are more common in discrete industries and
TPM practices are more likely to be implemented in process
industries
(continued )
process industries
Survey studies
Table I.
implementation in
regarding lean
Lean
135
implementation
26,1
136
Table I.
JMTM
(continued )
Type of industry and
Literature reference geographical area Focus of investigation Key findings
kaizen, “cross training” and “multi functional team.” Kanban and
“pull production” are rarely used
Scott et al. (2009) 46 respondents from Investigation of continuous 23.1 percent food processing units have implemented lean
Canadian food improvement programme manufacturing as structured continuous improvement programme
manufacturing industry
Hokoma et al. (2010) 32 iron and steel industries Investigation of status of Only 17 percent industries were using JIT/MRPII. Managerial
in Libya JIT and MRPII commitment is must to incorporate JIT
Gebauer et al. (2009) 95 pharmaceutical Investigation of lean Plant size and company type have positive effect lean
organizations from 20 manufacturing adoption implementation. Lean manufacturing helps to enhance operational
European countries performance. The adoption rate of lean manufacturing in
pharmaceutical sector is still low
Rahman et al. (2010) 187 manufacturing firms in Comparison of large and Large industries emphasize more on JIT whereas small industries
Thailand including process small industries in regards emphasize more on waste minimization. Adoption of lean
industries such as food and to lean practices manufacturing significantly affects operational performance
textile implementation
Small et al. (2011) 64 USA firms including 37 Assessing the In low or moderate level of technology firms, kaizen, benchmarking
process industries implementation of process and TQM were more popular initiatives in comparison with lean
management initiatives manufacturing
Bhasin (2012) 68 UK manufacturing firms Obstacles to adopt lean Major obstacles to implement lean are “insufficient supervisory
including process industries skills to implement lean,” “insufficient workforce skills to
implement lean,” “resistance to change” and “insufficient senior
management skills to implement lean”
Lyons et al. (2013) 62 UK process industries Implementation of lean Only those lean practices are extensively used in process industries
practices which are associated with elimination of wastes. Use of 5S, TPM,
quality management, visual control and SPC is widespread,
whereas use of cellular manufacturing, JIT production and pull
production is rare
Lean
Table I.
137
implementation
JMTM which employ JIT manufacturing practices are more profit earning then non JIT firms.
26,1 In a study of 65 Chinese industries including textile, chemical, petroleum and food
industries, Taj (2008) revealed that the major areas of performance improvement
through lean as perceived by the practitioners are inventory, team approach, process,
maintenance, layout and handling, suppliers, setup, quality and scheduling/control.
According to Singh et al. (2010a), with the application of lean manufacturing,
138 wastes related to human efforts, inventory, time to market, and manufacturing space
can be reduced.
2.3.3 Application of lean practices in process industries. Shah and Ward (2003)
investigated the adoption of 22 lean practices in discrete and process industries and
found that lean practices related to TPM prevailed more in process industries and lean
practices related to JIT production were less implemented in process industries.
In a study of 246 Chinese firms, Chen and Shang (2008) found that most notable
JIT components used by Chinese firms are “setup reduction,” 5S, kaizen, “cross
training” and “multi functional team.” Authors found that Kanban and “pull
production” are rarely used in Chinese firms.
Lyons et al. (2013) undertook a survey of 62 process industries in UK and explored
that only those lean practices are extensively used in process industries which are
associated with elimination of wastes. Authors found that use of 5S, TPM, “quality
management,” “visual control” and “statistical process control” (SPC) is widespread in
process industries, whereas use of “cellular manufacturing”, “JIT production” and “pull
production” is rare. In context to textile industries, Hodge et al. (2011) observed that
those who have implemented lean showed significant use of lean tools such as 5S,
kaizen, “value stream mapping” (VSM), and “visual control.” Whereas, lean tools
such as “cellular manufacturing,” kanban, “mistake proofing,” “policy deployment” and
“rapid improvements” were rarely used.
All these studies portray that 5S, TPM, “quality management,” “visual control,” SPC
and “work standardization” are in general applicable in process industries. These
studies also suggest that lean tools which are primarily related to JIT production
such as ‘pull production, kanban and “cellular manufacturing” are rarely used in
process industries.
2.3.4 Challenges to implement lean. Process industry environment imposes
certain challenges while implementing lean. In process industries batch sizes are
constrained by the fixed capacity of the processing equipment. If the batch quantity is
changed to a smaller quantity to implement JIT principles, this can result in poor
mixing and access waste (Ezingeard and Race, 1995). It can also need to expand
facilities, in order to have various sized mixing vessels to different batch sizes. Second,
large batch runs are essential for process industries due to large and inflexible
machines with long setup and changeover times which in turn demands maximum
utilization of resources (Powell et al., 2010). Houghton and Portougal (1995) warn that it
is difficult to achieve batch size reduction in process industries because it is associated
with setup reduction which is challenging with large fixed capacity equipments. Short
required lead times also limit the application of lean strategy in supply chains in
process industries (van der Vorst et al., 2001). Sewig (2008) and Melton (2005) describe
that resistance to change and confusion on validity are to be surmounted while
implementation of lean in process industries. Lack of training and unawareness about
lean concepts are also the major challenges which need proper attention while
implementing lean concepts in process industries. Another challenge to implement lean
in process industries is the difficulty to find expert personnel who leads the change Lean
(Kamakura, 2006). implementation
In a recent study of 68 UK manufacturing firms, Bhasin (2012) revealed following
obstacles to implement lean:
• insufficient supervisory skills to implement lean – 66 percent;
• employee attitudes/resistance to change – 60 percent; 139
• insufficient workforce skills to implement lean – 59 percent;
• insufficient senior management skills to implement lean – 58 percent;
• insufficient management time – 54 percent;
• cultural issues – 51 percent;
• cost of the investment – 50 percent;
• insufficient understanding of the potential benefits – 47 percent;
• insufficient internal funding – 46 percent;
• insufficient external funding – 39 percent; and
• a need to convince shareholders/owners – 22 percent.
2.3.5 Reasons of not implementing lean in process industries. In a study of 36 cement
industries in Libya, Hokoma et al. (2008) found that only 14 percent were implementing
JIT. Authors investigated major reasons as lack of top management support and
unfamiliarity with JIT practices, for low level of lean implementation. In another study
of iron and steel industries of Libya, Hokoma et al. (2010) listed following reasons of non
implementation of TQM/JIT techniques:
• lack of senior management support – 11.1 percent;
• lack of interest within the companies – 11.1 percent;
• the implementation requires formal approval – 0.0 percent;
• TQM/JIT/MRPII does not fit well with the company – 0.0 percent;
• the company is not familiar with TQM/JIT/MRPII – 77.8 percent;
• TQM/JIT/MRPII is too expensive to implement – 0.0 percent; and
• TQM/JIT/MRPII is too complex to implement – 0.0 percent.
It is evident from Table I that process industries have significant scope for
improvements regarding inventory control, waste elimination, quality management,
continuous improvements and customer satisfaction (Mady, 1991; Koumanakos, 2008;
Gebauer et al., 2009). However, process industries are far behind to the discrete
industries as far as lean adoption is concerned. Also, lean manufacturing is less popular
in process industries than in discrete manufacturing as a performance improvement
tool (Small et al., 2011). Hence, most lean manufacturing practices are still not
widespread in process industries (Bonavia and Marin, 2006).
Table I also revealed that “lean” adoption rate is higher in countries such
as USA, Australia and China, whereas in developing countries the implementation
of lean manufacturing is still not extensive (Hokoma et al., 2008; Hokoma
et al., 2010).
JMTM 2.4 Literature regarding lean implementation in Indian industries
26,1 Table II lists previous studies carried out in context to lean implementation in
manufacturing industries in India. Mukhopadhyay et al. (1998), Roy and Guin (1999),
Dhandapani et al. (2004), Upadhye et al. (2010) and recently, Gupta et al. (2013) have
attempted to study the implementation of lean manufacturing in certain process
industries in India and illustrated that “lean” can result in numerous benefits.
140 Upadhye et al. (2010) applied VSM in a biscuit manufacturing plant and found that
application of lean manufacturing resulted in increase in quality, decrease in inventory,
increase in timely deliveries, better utilization of space and equipments and reduction in
lead time. Gupta et al. (2013) studied the application of lean manufacturing in a radial
tyre manufacturing firm and found that organizational culture and human resource
management play a vital role to manage the change. Authors also found that major
causes of high manufacturing cost were over-processing and excessive defects.
Case studies discussed in Table II confirm that efforts to implement lean in process
industries are being carried out in India for quite a time. Although, these studies
provide some important insights about implementation of lean in Indian process
industries but their scope is confined to a particular firm or a particular type of process
industry. Hence, their results cannot be generalized, as stated by Gupta et al. (2013).
Second, Table II confirms that considerable empirical research has been carried out
in Indian manufacturing industries regarding lean implementation issues (Singh et al.,
2010b; Garza-Reyes et al., 2012; Ghosh, 2013), but there is barely any exploratory
research focussed upon process sector of India. Present empirical study will bridge this
gap in research by addressing the prominent issues regarding lean implementation in
Indian process industries and will furnish important outcomes for general application
and upcoming research.
3. Research methodology
3.1 Development of survey instrument
Comprehensive literature review lead to the establishment of four issues, namely,
“reasons of lean implementation,” “reasons of not implementing lean,” “lean tools” and
“challenges while implementing lean” to fully explore the status of lean implementation
in Indian process industries. Accordingly, the survey questionnaire was developed.
Subsequently, the draft of survey questionnaire was discussed with academicians,
practitioners and other experts to maintain the quality of questionnaire in the form of
appropriateness and focus on relevant issues. Finally, a structured questionnaire
was designed.
The questionnaire was split in three parts. First part contained five questions
about general information of the company. The second part of questionnaire had
three questions related to awareness about lean manufacturing. Last part of the
questionnaire was related to lean manufacturing issues. There were four questions in
the last part to identify “reasons of not implementing lean,” “reasons of implementing
lean,” “lean practices” and “challenges while implementing lean,” respectively.
Table III summarizes the lean implementation issues and their corresponding items
identified along with the literature sources.
A five point Likert scale which ranged from 1 ¼ “not use at all” to 5 ¼ “always use,”
was used for the measures of “lean practices.” For the rest of the issues same scale was
used for all items, ranged from 1 ¼ “not important” to 5 ¼ “most important.” A copy of
the survey questionnaire is furnished in Appendix.
Literature Type of process industry Type of study Major findings
Mukhopadhyay et al. (1998) Pharmaceutical Case study Integrated production planning system was helpful to implement lean
concepts in pharmaceutical firm
Roy and Guin (1999) Steel Case study Application of JIT in purchasing resulted in considerable cost savings
Dhandapani et al. (2004) Steel Case study Applying JIT production resulted in release of working capital and
decrease in inventory
Mahapatra and Mohanty 29 continuous Survey Most important lean tools are TPM, “automatic line stoppage,” VSM,
(2007) manufacturing industries “workplace organization” and “visual control.” Least important lean
in India practices are “work standardization,” “multipurpose handling” and takt
time. Continuous process industries perceive higher benefits than
discrete industries from lean manufacturing. Lack of management
support is most prevailing problem in implementing lean
Seth et al. (2008) Comprising 37 respondents Survey Used value stream mapping and proved that there exist several non
from edible oil industry value added activities in the supply chain of edible oil industry
Upadhye et al. (2010) Biscuit Case study Used value stream mapping and identified several wastes in the
manufacturing of biscuits
Singh et al. (2010b) 127 manufacturing Survey Major reasons of lean implementation in Indian manufacturing
industries industries included reduction of delivery time, reduction in cost,
enhancing range of products and due to stiff competition
Upasani (2012) 47 process industries Survey Indian process industries lag far behind the other industries in
implementation of supply chain management practices such as lean
manufacturing
Garza-Reyes et al. (2012) 46 manufacturing Survey Most important reason of lean implementation in Indian industries is
industries customer satisfaction. Kaizen is perceived as an important lean tool by
Indian industries
Ghosh (2013) 79 manufacturing Survey Although, the concept of lean is new for Indian industries, still several
industries Indian companies are at advanced level of lean implementation, and by
implementing lean they have achieved better operational performance
(continued )
Indian industries
Lean
Previous studies
141
implementation in
regarding lean
Table II.
implementation
26,1
142
JMTM
Table II.
Literature Type of process industry Type of study Major findings
Khadse et al. (2013) 31 large manufacturing Survey TPM, continuous improvements and inventory reduction are primarily
industries used lean practices in Indian manufacturing industries. Reduction in
cost and wastes are the major benefits of lean implementation, while
“lack of understanding,” lack of top management support’ and
“financial benefits not recognized” are the major obstacles while
implementing lean
Gupta et al. (2013) Tyre Case study The important enablers for successful lean implementation are
organizational culture and human resource management. Over-
processing and excessive defects are the most important wastes in
radial tyre manufacturing. Lean practices are still in the nascent stage
in the industry
Lean Implementation issue No. of items Items Literature source Cronbach’s α
Reasons of implementing 8 Elimination of wastes White (1993), Taj (2008), Singh 0.657
lean To decrease production costs et al. (2010b)
To improve quality
To facilitate JIT production
To increase demand management efficiency
To increase customer satisfaction
To increase supply chain efficiency
To increase utilization of space
Lean practices 20 Value stream mapping (VSM) Shah and Ward (2003), Lyons 0.800
5S et al. (2013)
Quick changeover techniques (SMED)
Setup reduction
Lot-size reduction
Total productive maintenance (TPM)
Visual control
Work standardization
Statistical process control (SPC)
Quality management programme
Takt time
Pull production
production levelling
mistake proofing
Kanban
Cellular manufacturing
Flexible and cross functional teams
Continuous improvement programmes
Supplier integration and partnership
Long-term relationship with suppliers
(continued )
internal consistency
Literature summary
of lean issues and
Table III.
Lean
144
JMTM
Table III.
Lean Implementation issue No. of items Items Literature source Cronbach’s α
Challenges to implement 11 To facilitate small batch production Bhasin (2012), Ezingeard and 0.603
lean To identify techniques for setup time reduction Race (1995), Houghton and
To deal with typical process characteristics (time and Portougal (1995), Powell et al.,
temperature, etc.) (2010), van der Vorst
To arrange lean implementation experts et al. (2001)
Scepticism/ cultural barriers
Lack of training
Short lead times
Perishable nature of products
Improper information exchange across supply chain
To facilitate JIT production
To facilitate JIT purchasing
Reasons of not 9 Large batch production is necessary for capacity Ezingeard and Race (1995), 0.721
implementing lean utilization Hokoma et al. (2008),
Process industries already have continuous Hokoma et al. (2010)
production
Lack of education and expertise on lean
Lack of financial resources
Lack of time
Cultural barriers (resistance to change)
Specific characteristics of process industries (time,
temperature and process dependence)
Lack of senior management’s interest and support
Lean is complex to implement
3.2 Survey administration Lean
A sample of 500 companies was taken from directory of ISO: 9001 certified process implementation
industries in India. Primarily, postal survey method was used to administer the
questionnaire. It was observed that initially the response rate was low in-spite of
repeated reminders. Hence, it was decided to search other means to increase response
rate. A few responses were collected through conducting face to face interviews. In
some instances, responses were collected through third party channels. These efforts 145
helped, and the response rate increased. To increase the response rate further,
emails were sent, followed by a telephonic request for reply. The questionnaire was
addressed to higher executives who were responsible for production. Finally, 126
responses received.
4. Observations of survey
Out of contacted 500 Indian process industries, 126 responded. In all, six responses
were incomplete which were excluded from further analysis. Hence, the number of valid
responses was 120. Therefore, the response rate achieved was 24 percent. It is worth
mentioning that response rate achieved in present study is similar to other such studies
carried out in Indian context. Ghosh (2013) in a study of lean manufacturing
implementation in Indian manufacturing companies received the response rate of 20
percent. In similar studies, Upasani (2012) and Pandey et al. (2010) could achieve the
response rate of 17.5 and 18.02 percent, respectively. Nonetheless, according to
Malhotra and Grover (1998) and Sahay et al. (2006) this response rate is adequate in
India for this type of surveys.
Respondents were asked if they are familiar with concept of lean manufacturing.
Surprisingly, 85 (70.8 percent) respondents replied that they were familiar with lean
manufacturing. For the reply to the question that if they think lean is useful for process
industries, 86 (71.7 percent) respondents replied in a “yes.” Therefore, the study
suggests that most of the organizations from Indian process sector are aware of the
concept of lean manufacturing and also think that lean is useful for process industries.
Not surprisingly, only 45 (37.5 percent) respondents have implemented lean
manufacturing (see Table IV).
Our study explored that out of 105 respondents from large process industries 45
(42.9 percent) have implemented lean whereas, 60 (57.1 percent) have not implemented
lean manufacturing. Surprisingly, all the respondents from small process industries
denied the adoption of lean manufacturing.
Sig. Mean
Reasons of not implementing lean Mean Rank t (two-tailed) difference
Sig. Mean
Lean tools Mean Rank t (two-tailed) difference
Sig. Mean
Challenges while implementing lean Mean Rank t (two-tailed) difference
• Although, concept of lean is relatively new for India, still Indian process
industries are aware of lean manufacturing and perceive lean to be useful for
performance improvement.
•
JMTM Driving forces to implement lean are very much identical in process and discrete
26,1 manufacturing industries in India, however, Indian process industries are far
behind than other manufacturing industries in India as far as lean
implementation is concerned. Hence, there is ample scope for adoption of lean
concepts in Indian process industries.
• Indian process industries those who have implemented lean found lean to be very
152 useful to reduce wastes and to increase quality.
• Major lean practices being implemented by Indian process industries are
primarily those which are related to waste elimination or improvement in quality.
Lean practices which are related to JIT production are still not widespread in
Indian process industries.
• Indian process industries found that biggest challenge while implementing lean
is to produce in small batches. To arrange for lean experts and to impart training
to employees are also big challenges while implementing lean. In-fact, managers
in Indian process industries believe that “to produce in large batches for proper
utilization of capacity and equipments” is a major reason of not choosing lean
manufacturing for performance improvement.
• “Cultural barrier” is no more an important reason of not implementing lean in
process industries. This finding is very important in Indian context. This
outcome suggests that acceptance for any change has been gradually increased,
thus, it is much easier now to implement new methodologies such as lean, in
Indian process industries.
References
Abdulmalek, F.A. and Rajgopal, J. (2007), “Analyzing the benefits of lean manufacturing and
value stream mapping via simulation: a process sector case study”, International Journal of
Production Economics, Vol. 107 No. 1, pp. 223-236.
Ahmad, M., Dhafr, N., Benson, R. and Burgess, B. (2005), “Model for establishing theoretical
targets at the shop floor level in specialty chemicals manufacturing organizations”,
Robotics & Computer-Integrated Manufacturing, Vol. 21 Nos 4/5, pp. 291-400.
Antony, J. (2011), “Six sigma vs lean: some perspectives from leading academics and
practitioners”, International Journal of Productivity and Performance Management, Vol. 60
No. 2, pp. 185-190.
Ashayeri, J., Teelen, A. and Selen, W. (1996), “A production and maintenance planning model for
the process industry”, International Journal of Production Research, Vol. 34 No. 12,
pp. 3311-3326.
JMTM Besson, D. and Haddadj, S. (1999), “Strategies developed by US chemical firms to resolve their
skill shortages”, Journal of European Industrial Training, Vol. 23 No. 7, pp. 353-362.
26,1
Bhasin, S. (2012), “Prominent obstacles to lean”, International Journal of Productivity and
Performance Management, Vol. 61 No. 4, pp. 403-425.
Billesbach, J.T. (1994), “Applying lean production principles to a process facility”, Production &
Inventory Management Journal, Vol. 35 No. 3, pp. 40-44.
154 Bonavia, T. and Marin, J.A. (2006), “An empirical study of lean production in the ceramic tile
industry in Spain”, International Journal of Operations & Production Management, Vol. 26
No. 5, pp. 505-631.
Chen, Z. and Shang, J.S. (2008), “Manufacturing planning and control technology versus
operational performance: an empirical study of MRP and JIT in China”, International
Journal of Manufacturing Technology & Management, Vol. 13 No. 1, pp. 4-29.
Chowdary, B.V. and George, D. (2012), “Improvement of manufacturing operations at
a pharmaceutical company”, Journal of Manufacturing Technology Management, Vol. 23
No. 1, pp. 56-75.
Cook, R.C. and Rogowski, R.A. (1996), “Applying JIT principles to continuous process
manufacturing supply chains”, Production & Inventory Management Journal, Vol. 37 No. 1,
pp. 12-16.
Cox, A. and Chicksand, D. (2005), “The limits of lean management thinking: multiple retailers
and food and farming supply chains”, European Management Journal, Vol. 23 No. 6,
pp. 648-662.
Crama, Y., Pochet, Y. and Wera, Y. (2001), “A discussion of production planning approaches in
the process industry”, CORE Discussion Paper Nos 01/42, UCL, University of Liege.
Dangayach, G.S. and Deshmukh, S.G. (2003), “Evidence of manufacturing strategies in Indian
industry: a survey”, International Journal of Production Economics, Vol. 83 No. 3,
pp. 279-298.
Dennis, D. and Meredith, J. (2000), “An analysis of process industry production and inventory
management systems”, Journal of Operations Management, Vol. 18 No. 6, pp. 683-699.
Dhandapani, V., Potter, A. and Naim, M. (2004), “Applying lean thinking: a case study of an
Indian steel plant”, International Journal of Logistics Research & Applications, Vol. 7 No. 3,
pp. 239-250.
Dov, M. (1992), “A manufacturing process with a different flavour: JIT and the ice cream
industry”, Industrial Management, Vol. 34 No. 2, pp. 10-13.
Dunstan, K., Lavin, B. and Sanford, R. (2006), “The application of lean manufacturing in a mining
environment”, Proceedings of the International Mine Management Conference in
Melbourne, pp. 145-157.
Ezingeard, J.N. and Race, P. (1995), “Spreadsheet simulation to aid capacity management of batch
chemical processing using JIT pull control”, International Journal of Operations &
Production Management, Vol. 15 No. 10, pp. 82-88.
Fransoo, J.C. and Rutten, W.G.M.M. (1994), “A typology of production control situations in
process industries”, International Journal of Operations & Production Management, Vol. 14
No. 12, pp. 47-57.
Fullerton, R.R. (2003), “Performance measurement and reward systems in JIT and non-JIT firms”,
Journal of Cost Management, Vol. 17 No. 6, pp. 40-48.
Garza-Reyes, A.J., Parkar, H.S., Oraifige, I., Soriano-Meier, H. and Harmanto, D. (2012), “An
empirical-exploratory study of the status of lean manufacturing in India”, International
Journal of Business Excellence, Vol. 5 No. 4, pp. 395-412.
Gebauer, H., Kickuth, M. and Friedli, F. (2009), “Lean management practices in the Lean
pharmaceutical industry”, International Journal of Services & Operations Management,
Vol. 5 No. 4, pp. 463-481.
implementation
Ghosh, M. (2013), “Lean manufacturing performance in Indian manufacturing plants”, Journal of
Manufacturing Technology Management, Vol. 24 No. 1, pp. 113-122.
Gunasekaran, A. (1998), “Agile manufacturing: enablers and an implementation framework”,
International Journal of Production Research, Vol. 36 No. 5, pp. 1223-1247. 155
Gupta, V., Acharya, P. and Patwardhan, M. (2013), “A strategic and operational approach to
assess the lean performance in radial tyre manufacturing in India – a case based study”,
International Journal of Productivity and Performance Management, Vol. 62 No. 6,
pp. 634-651.
Gyampah, K. and Gargeya, V. (2001), “Just-in-time manufacturing in Ghana”, Industrial
Management & Data Systems, Vol. 101 No. 3, pp. 106-113.
Hodge, G.L., Goforth, K.R., Joines, J.A. and Thoney, K. (2011), “Adapting lean manufacturing
principles to the textile industry”, Production Planning & Control, Vol. 22 No. 3,
pp. 237-247.
Hokoma, R.A., Khan, M.K. and Hussain, K. (2008), “Investigation into the implementation
stages of manufacturing and quality techniques and philosophies within the Libyan
cement industry”, Journal of Manufacturing Technology Management, Vol. 19 No. 7,
pp. 893-907.
Hokoma, R.A., Khan, M.K. and Hussain, K. (2010), “The present status of quality and
manufacturing management techniques and philosophies within the Libyan iron and steel
industry”, The TQM Journal, Vol. 22 No. 2, pp. 209-221.
Houghton, E. and Portougal, V. (1995), “A planning model for just-in-time batch manufacturing”,
International Journal of Operations & Production Management, Vol. 15 No. 9, pp. 9-25.
Jain, R. and Lyons, A.C. (2009), “The implementation of lean manufacturing in the UK food and
drink industry”, International Journal of Services & Operations Management, Vol. 5 No. 4,
pp. 548-573.
Jeanes, C.F. (1995), “Achieving and exceeding customer satisfaction at Milliken”, Managing
Service Quality, Vol. 5 No. 4, pp. 6-11.
Kamakura, Y. (2006), Corporate Structural Change and Social Dialogue in the Chemical Industry,
International Labour Organization Publication, International Labour Office, Geneva.
Khadse, P.B., Sarode, A.D. and Wasu, R. (2013), “Lean manufacturing in Indian industries:
a review”, International Journal of Latest Trends in Engineering and Technology”, Vol. 3
No. 1, pp. 175-181.
King, P.L. (2009), Lean for the Process Industries: Dealing with Complexities, Productivity Press,
New York, NY.
Koumanakos, D.P. (2008), “The effect of inventory management on firm performance”,
International Journal of Productivity & Performance Management, Vol. 57 No. 5,
pp. 355-369.
Lasa, I.S., Laburu, C.O. and Lila, R.d.C. (2008), “An evaluation of the value stream mapping tool”,
Business Process Management Journal, Vol. 14 No. 1, pp. 39-52.
Lehtonen, J.M. and Holmstrom, J. (1998), “Is just-in-time applicable in paper industry logistics?”,
Supply Chain Management, Vol. 3 No. 1, pp. 21-32.
Lyons, A.C., Vidamour, K., Jain, R. and Sutherland, M. (2013), “Developing an understanding of
lean thinking in process industries”, Production Planning and Control, Vol. 24 No. 6,
pp. 475-494.
JMTM Mady, M.T. (1991), “The effect of type of industry on inventory investments and structure: the
Egyptian case”, International Journal of Operations & Production Management, Vol. 11
26,1 No. 6, pp. 55-65.
Mahapatra, S.S. and Mohanty, S.R. (2007), “Lean manufacturing in continuous process industry:
an empirical study”, Journal of Scientific & Industrial Research, Vol. 66 No. 1, pp. 19-27.
Malhotra, M.K. and Grover, V. (1998), “An assessment of survey research in POM: from
156 constraints to theory”, Journal of Operation Management, Vol. 14 No. 4, pp. 407-425.
Melton, T. (2005), “The benefits of lean manufacturing: what lean thinking has to offer the
process industries”, Chemical Engineering Research & Design, Vol. 83 No. A6, pp. 662-673.
Moriones, A.B., Pintado, A.B. and Cerio, J.M. (2008),“The role of organizational context and
infrastructure practices in JIT implementation”, International Journal of Operations &
Production Management, Vol. 28 No. 11, pp. 1042-1066.
Mukhopadhyay, S.K. and Shanker, S. (2005), “Kanban implementation at a tyre manufacturing
plant: a case study”, Production Planning & Control, Vol. 16 No. 5, pp. 488-499.
Mukhopadhyay, S.K., Dwivedy, J. and Kumar, A. (1998), “Design and implementation of an
integrated production planning system for a pharmaceutical manufacturing concern in
India”, Production Planning and Control: The Management of Operations, Vol. 9 No. 4,
pp. 391-402.
Pandey, V.C., Garg, S.K. and Shankar, R. (2010), “Impact of information sharing on competitive
strength of Indian manufacturing enterprises – an empirical study”, Business Process
Management, Vol. 16 No. 2, pp. 226-243.
Powell, D., Alfnes, E. and Semini, M. (2010), “The application of lean production control methods
within a process-type industry: the case of hydro automotive structures”, Proceedings of
the International Conference on Advances in Production Management Systems in Bordeaux,
pp. 243-250.
Rahman, S., Laosirihongthong, T. and Sohal, A. (2010), “Impact of lean strategy on operational
performance: a study of Thai manufacturing companies”, Journal of Manufacturing
Technology Management, Vol. 21 No. 7, pp. 839‐852.
Roy, R.N. and Guin, K.K. (1999), “A proposed model of JIT purchasing in an integrated steel
plant”, International Journal of Production Economics, Vol. 59 Nos 1/3, pp. 179-187.
Sahay, B.S., Gupta, N.D. and Mohan, R. (2006), “Managing supply chains for competitiveness:
the Indian scenario”, Supply Chain Management: An International Journal, Vol. 11 No. 1,
pp. 15-24.
Salaheldin, S.I. (2005), “JIT implementation in Egyptian manufacturing firms: some empirical
evidence”, International Journal of Operations & Production Management, Vol. 25 No. 4,
pp. 354-370.
Scott, B.S., Wilcock, A.E., Kanetkar, V. (2009), “A survey of structured continuous improvement
programs in the Canadian food sector”, Food Control, Vol. 20 No. 3, pp. 209-217.
Seth, D., Seth, N. and Goel, D. (2008), “Application of value stream mapping (VSM) for
minimization of wastes in the processing side of supply chain of cottonseed oil industry
in Indian context”, Journal of Manufacturing Technology Management, Vol. 19 No. 4,
pp. 529-550.
Sewig, A. (2008), “Evolution in thinking and processes?”, Drug Discovery Today Technologies,
Vol. 5 No. 1, pp. e9-e14.
Shah, N. (2005), “Process industry supply chains: advances and challenges”, Computers &
Chemical Engineering, Vol. 29 No. 6, pp. 1225-1235.
Shah, R. and Ward, P.T. (2003), “Lean manufacturing: context, practices bundles, and
performance”, Journal of Operations Management, Vol. 21 No. 2, pp. 129-149.
Shah, R. and Ward, P.T. (2007), “Defining and developing measures of lean production”, Journal Lean
of Operations Management, Vol. 25 No. 4, pp. 785-805.
implementation
Sharma, R.K., Kumar, D. and Kumar, P. (2005), “FLM to select suitable maintenance strategy in
process industries using MISO model”, Journal of Quality in Maintenance Engineering,
Vol. 11 No. 4, pp. 359-374.
Simons, D. and Zokaei, K. (2005), “Application of lean paradigm in red meat processing”, British
Food Journal, Vol. 107 No. 4, pp. 192-211. 157
Singh, B., Garg, S.K. and Sharma, S.K. (2010b), “Scope for lean implementation: a survey
of 127 Indian industries”, International Journal of Rapid Manufacturing, Vol. 1 No. 3,
pp. 323-333.
Singh, B., Garg, S.K., Sharma, S.K. and Grewal, C. (2010a), “Lean implementation and its benefits
to production industry”, International Journal of Lean Six Sigma, Vol. 1 No. 2, pp. 157-168.
Small, M.H., Yasin, M.M. and Alvi, J. (2011), “Assessing the implementation and effectiveness of
process management initiatives at technologically consistent firms”, Business Process
Management Journal, Vol. 17 No. 1, pp. 6-20.
Sohal, A.S. (1996), “Developing a lean production organization: an Australian case study”,
International Journal of Operations and Production Management, Vol. 16 No. 2, pp. 91-102.
Sohal, A.S. and Egglestone, A. (1994), “Lean production: experience among Australian organizations”,
International Journal of Operations & Production Management, Vol. 14 No. 11, pp. 35-51.
Soriano-Meier, H. and Forrester, P.L. (2002), “A model for evaluating the degree of leanness of
manufacturing firms”, Integrated Manufacturing Systems, Vol. 13 No. 2, pp. 104-109.
Taj, S. (2008), “Lean manufacturing performance in China: assessment of 65 manufacturing
plants”, Journal of Manufacturing Technology Management, Vol. 19 No. 2, pp. 217-234.
Upadhye, N., Deshmukh, S.G. and Garg, S. (2010), “Lean manufacturing in biscuit manufacturing
plant: a case”, International Journal of Advanced Operations Management, Vol. 2 No. 1,
pp. 108-139.
Upasani, S. (2012), “Emerging supply chain management practices in Indian manufacturing
industries”, International Journal of Research in IT & Management, Vol. 2 No. 2,
pp. 1237-1248.
van der Vorst, J.G.A.J., van Dijk, S.J. and Beulens, A.J.M. (2001), “Supply chain design in the food
industry”, International Journal of Logistics Management, Vol. 12 No. 2, pp. 73-85.
White, R.E. (1993), “An empirical assessment of JIT in US manufacturers”, Production &
Inventory Management Journal, Vol. 34 No. 2, pp. 38-42.
White, R.E. and Prybutok, V. (2001), “The relationship between JIT practices and type of
production system”, Omega, Vol. 29 No. 2, pp. 113-124.
Womack, J.P. and Jones, D.T. (1996), Lean Thinking: Banish Waste and Create Wealth in Your
Corporation, Simon and Schuster, New York, NY.
Womack, J.P., Jones, D.T. and Roos, D. (1990), The Machine That Changed the World, Harper
Perennial, New York, NY.
Zanoni, S. and Zavanella, L. (2005), “Model and analysis of integrated production-inventory
system: the case of steel production”, International Journal of Production Economics,
Vols 93/94, pp. 197-205.
Further reading
Jonsson, P. and Mattsson, S. (2006), “A longitudinal study of material planning applications in
manufacturing companies”, International Journal of Operations & Production
Management, Vol. 26 No. 9, pp. 971-995.
JMTM Appendix. Lean Assessment Questionnaire
26,1
158
Lean
implementation
159
JMTM
26,1
160
For instructions on how to order reprints of this article, please visit our website:
www.emeraldgrouppublishing.com/licensing/reprints.htm
Or contact us for further details: permissions@emeraldinsight.com
Reproduced with permission of the copyright owner. Further reproduction prohibited without
permission.