Professional Documents
Culture Documents
12.25 MX-18 Broca
12.25 MX-18 Broca
12.25 MX-18 Broca
UltraMAX FEATURES
• Single Energizer Seal & Bearing System (SEM) -
more robust design to provide consistency and
reliability in all applications.
• Anti-Mud Packing System (Excluder) - secondary
static seal eliminates detrimental effects of mud
packing on the seal.
• Grease and Lubrication System (Equalizer( - new
grease formulation better lubricates the seal faces.
Improved compensation system improves reliability.
• Clean Sweep Hydraulics - improved cleaning of
cutting structure for better ROP in bit balling
formations .
• BOSS Stabilization - improves bit stability.
• GT Cutting Structures with New Carbide Grades.
• Shirttail Motor Hardfacing - standard.
• Diamond Enhanced Modifications - optional.
PRODUCT SPECIFICATIONS
Assembly Number:M2218A1
1998 Hughes Christensen Proprietary Notice: This information sheet is property of Hughes Christensen and is considered confidential.
Written consent must be obtained from Hughes Christensen to reproduce, copy, or use in part or in whole the drawings or information contained on this sheet. The ranges of bit weight and RPM shown
are representative of typical operating parameters, but will not necessarily yield optimum bit life or lowest drilling cost. It is not recommended that the upper limits of both weight and RPM be run
simultaneously. Contact your local Hughes Christensen representative for recommendations in your area.
12 ¼″ MX-18
APPLICATION
• Primary
• Steerable and straight hole motors
• High RPM rotary systems
• Other Applications
• Abrasive formations
• High temperature applications up to 400 degrees F.
bottom hole circulating temperature
• Long intervals
• Cutting structure is intended for soft, low compressive strength
formations. (0 - 15,000 psi unconfined compressive strength -
shale, clay, salt, limestone, sand & trace chert).
PRODUCT SPECIFICATIONS
Offset/Skew: 6/16 in/ 3.83°
Pin Angle: 33°
Bearing Diameter: 3 - 2/16 in REASONS FOR CHANGE
Cone Metallurgy: Carb Journal Surface w/ Brush Ag • UltraMax Product Line
Plated Thrust Face & Pilot Hole
Head Metallurgy: Carb & B4 Hardfaced Journal
O.D. Features: Motor HF & BOSS
DESCRIPTION QUANTITY/CONE
Row SHAPE DIAM (IN.) PROJ (IN.) EFF PROJ GRADE #1 #2 #3 TOTAL
1 GAGE .3778 .047 .000 PB671 27 27 27 81
2 TRIMM .4403 .234 .000 941 HIP 13 13 0 26
2 TRIMM .5028 .234 .000 941 HIP 0 0 12 12
3 PFWEDG .7533 .375 .375 941 HIP 13 13 12 38
4 SSCOOP .7533 .594 .387 45B HIP 13 0 0 13
4 SSCOOP .7533 .594 .396 45B HIP 0 13 0 13
4 SSCOOP .7533 .594 .260 45B HIP 0 0 14 14
5 SSCOOP .7533 .625 .330 45B HIP 9 0 0 9
5 SSCOOP .7533 .625 .269 45B HIP 0 12 0 12
5 SSCOOP .7533 .625 .529 45B HIP 0 0 6 6
6 SSCOOP .6278 .359 .359 45B HIP 1 0 0 1
6 SSCOOP .7533 .469 .469 45B HIP 0 3 0 3
TOTAL 76 81 71 228
TOTAL EXCLUDING GAGE 147
1998 Hughes Christensen Proprietary Notice: This information sheet is property of Hughes Christensen and is considered confidential.
Written consent must be obtained from Hughes Christensen to reproduce, copy, or use in part or in whole the drawings or information contained on this sheet. The ranges of bit weight and RPM shown
are representative of typical operating parameters, but will not necessarily yield optimum bit life or lowest drilling cost. It is not recommended that the upper limits of both weight and RPM be run
simultaneously. Contact your local Hughes Christensen representative for recommendations in your area.