Professional Documents
Culture Documents
Catalogo Kimax Kimpble
Catalogo Kimax Kimpble
CATEGORIES PAGE(S)
ADAPTERS 3
BEVEL-SEAL™
ASTM METHODS 19
Search Catalog by ASTM Methods
BEAKERS 3
Low Form Griffin, Low Form Heavy Duty, Tall Form Berzelius
BOTTLES 4
Carboy, Gasoline, Reservoir, Solution, Media, RAY-SORB®, Dilution
CONTAINERS 5
Sample
JARS 5
Cold Test
BURETS 5, 6, 7
Class A, Class B, Serialized & Ceritified, Automatic, Micro, Dispensing, Gas, Tutwiler
COLUMNS 7
Neutral Oil and Loss
CONDENSERS 8, 9
Friedrich, Coil-Type Reflux, Liebig, Graham, Allihn, West
CYLINDERS 9, 10
Class A, Class B, Measuring, Reverse Graduations, Emulsion, Hydrometer, Single Metric Scale
DISTILLATION 10, 11
Dean Stark, Modified Dean Stark, Bidwell-Sterling, Moisture Test, Engler, Barrett
FLASKS 11, 12, 13, 14
Class A, Graduated, Jointed, Narrow Mouth, Wide Mouth, Erlenmeyer, Boiling, Round Bottom
FUNNELS 15
Short Stem, Addition, 1-1/2” Stem, Squibb
OXIDATION 15
Cell
PETROCHEMICAL 15, 16
Water in Crude Oil, Filter Stick
PIPETS 16
Class B, Mohr Style, Reusable, Unserialized, To Deliver, Volumetric
RAMSBOTTOM 16
Coking Bulb
RECEIVERS 10
Dean Stark, Modified Dean Stark, Bidwell-Sterling
TUBES 16, 17, 18
Measuring, Sampling, Graduated, Goetz, Centrifuge, California, Oil & Weathering, Soil Analysis
VISCOMETER 18
Cannon-Fenske
* The PDF version of this catalog allows you to click on the product name or category listed above to be taken
directly to the product page.
8 3
Unsaturation Gasoline Bottles Solution Bottle with Color-Coded PTFE Flathead
KIMAX® bottle used in the determination of unsaturated hydrocarbons Stopper
in gasoline. These KIMAX® bottles are designed for storage and dispensing of
solutions.
• Manufactured from 33 expansion, low extractable borosilicate • Bottle necks are Standard Taper ground to accept flathead color-
glass conforming to USP Type I and ASTM E438, Type I, Class A coded PTFE stoppers
requirements • Replacement stoppers are Cat. No. 41941R.
• Manufactured from 33 expansion, low extractable borosilicate
The body of the bottle (approximately 45 mL capacity) is a glass conforming to USP Type I and ASTM E438, Type I, Class A
“reaction vessel” in which an accurately measured sample requirements
is pipetted into the bottle; excess reagent is then added. Kimble Chase Capacity Standard Taper Case
After the reaction is complete, more reagent is added to Cat. No. (mL) Stopper Size Qty
raise the “fat column” into the calibrated neck of the bottle, 15097-100 100 14 1
where results are read directly as a percentage of fat in the 15097-250 250 19 6
15097-500 500 24 6
sample. 15097-1000 1000 29 6
Kimble Chase Neck Capacity Case 15097-2000 2000 29 4
Cat. No. (%) Tolerance (%) Qty
15066-10 100 (10 mL) ±1 12
GL 45 Media Bottles
Ideal for general laboratory use including mixing, storing or transporting
culture media, chemicals or solvents.
Heavy Duty Carboy
The heavy duty construction of these bottles is designed to prolong • Enhanced graduations and marking spot made with chemically
resistant white enamel paint
life expectancy with harder than normal usage. Ideal for storage and
• 30 mm ID opening
dispensing of solutions. • Autoclavable
• Supplied without caps or with linerless GL 45 screw thread caps
• KIMAX® carboy-style bottle with sloping shoulders • Replaceable clear (natural) drip-free polypropylene pour ring is
included on each bottle
• Neck is tooled for a uniform fit with a #12 rubber stopper
• Manufactured from 33 expansion, low extractable borosilicate
• Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A
glass conforming to USP Type I and ASTM E438, Type I, Class A requirement
requirements Kimble Chase Capacity Graduation Case
Kimble Chase Capacity Capacity Case Cat. No. (mL) Range (mL) Qty
Cat. No. (mL) (gallons) Qty 14395-100 100 20-80 10
14950-25 9500 2.5 1 14395-250 250 50-200 10
14950-35 13200 3.5 1 14395-500 500 100-400 10
14950-120 45500 12.0 1 14395-1000 1000 100-900 10
14950-500 19000 5.0 1 14395-2000 2000 400-1800 4
14395-5000 5000 1000-4000 1
14395-10000 10000 2000-8000 1
8 4
Class A Burets, Serialized and Certified,
Static Dilution Bottles Straight Bore PTFE Stopcock, with Dust Cap
The static dilution bottle provides a simple, inexpensive means to
prepare, store and use standards of volatile organic compounds. KIMAX® precision bore buret is permanently marked with an
individual serial number. Supplied with a Certificate of
Graduation Accuracy. Designed from ASTM Specification
• Standards are prepared by injecting a small quantity of the pure E287, Class A requirements. KIM-KAP® dust cap is included.
compounds into the bottle and using heat to fully evaporate.
• A push-pull, color-coded, (green-for-open, red-for-closed) Mininert Delivery stem of the 10 mL size is 115 mm long to meet
requirements of potentiometric titration burets (ASTM D664).
valve is supplied for easy use and long lasting performance
PTFE plug for all sizes is 2. Scale is a durable white ceramic
• The valve is excellent for sealed tube reactions, long term storage enamel. Replacement stopcock is 821001-0002.
of standards or periodic addition of reactants Kimble Chase Capacity Tolerance Case
• Sample aliquots are withdrawn using a gas-tight syringe Cat. No. (mL) (mL) Qty
• Septum seal prevents leakage when using a syringe 17027F-10 10 ±0.02 1
• Standards prepared by this method are stable for up to one week 17027F-25 25 ±0.03 1
17027F-50 50 ±0.05 1
• Manufactured from 33 expansion, low extractable
17027F-100 100 ±0.10 1
borosilicate glass conforming to USP Type I and
ASTM E438, Type I, Class A requirements
8 5
Class A Serialized and Certified Reservoir Fill Burets Class B Straight Bore Burets with PTFE Stopcock
with Three-Way Stopcock Used in general purpose volumetric analysis and titrations where Class B
Used for general purpose titrations requiring traceable volumetric tolerances are appropriate.
accuracy.
• Funnel fill style buret
• Permanently marked with an individual serial number • Replacement 2 mm straight bore PTFE stopcock plug is
and traceable to NIST Standards 821001-0002.
• Supplied with a Certificate of Graduation Accuracy • Easy-to-read durable black ceramic enamel scale
• Filling tube accepts 1/4 inch ID flexible tubing • Designed from ASTM Specification E287, Class B
• Precision ground tips assure uniform outflow requirements
• KIM-KAP® dust cap is included • Ref: ASTM Method D974
• Filled through a self-lubricating PTFE stopcock plug • Manufactured to the specifications found in ASTM E694
• Easy-to-read durable white enamel scale • Calibrated to the accuracy requirements found in ASTM
• Reservoir fill style buret Specification E542
• Replacement 2 mm bore size three-way stopcock is • Manufactured from 33 expansion, low extractable
823001-0002. borosilicate glass conforming to USP Type I and ASTM
• Designed from ASTM E287, Class A requirements E438, Type I, Class A requirements
• Manufactured to the specifications found in ASTM E694 Kimble Chase Capacity Tolerance Case
• Calibrated to the accuracy requirements found in ASTM Cat. No. (mL) (mL) Qty
Specification E542 17026F-10 10 ±0.04 1
17026F-25 25 ±0.06 1
• Manufactured from 33 expansion, low extractable 17026F-50 50 ±0.10 1
borosilicate glass conforming to USP Type I and ASTM 17026F-100 100 ±0.20 1
E-438, Type I, Class A requirements
Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty
17052F-25 25 ±0.03 1
17052F-50 50 ±0.05 1
17052F-100 100 ±0.10 1 Automatic Burets
KIMAX® buret ideal for repeat titrations requiring traceable volumetric
accuracy.
8 6
Dispensing Burets
Large capacity KIMAX® burets used for dispensing laboratory solvents or
solutions for a variety of clinical and industrial applications.
Micro Buret with Side Reservoir
Used for small volume titrations.
• Supplied with a chemically-resistant, self-lubricating PTFE
stopcock
• Side reservoir capacity is approximately 70 mL
• Easy-to-read durable white ceramic enamel scale
• Easy-to-read durable white ceramic enamel scale
• Replacement 4 mm straight bore stopcock plug is
• Replacement 2 mm straight bore stopcock plug
821001-0004.
is 821001-0002, and replacement stopper is a
• Manufactured from 33 expansion, low extractable
medium length 14/20 standard taper glass stopper
borosilicate glass conforming to USP Type I and ASTM
• Supplied with two chemically-resistant, self-lubricating
E438, Type I, Class A requirements
PTFE stopcock plugs
• Manufactured to the specifications found in ASTM E694 Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty
• Calibrated to the accuracy requirements found in ASTM
17080F-250 250 ±2.0 2
Specification E542 17080F-500 500 ±2.5 2
• Manufactured from 33 expansion, low extractable 17080F-1000 1000 ±5.0 2
borosilicate glass conforming to USP Type I and ASTM
E438, Type I, Class A requirements
Tutwiler Gas Burets
This buret is designed for use with high sulfur content gas streams.
Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty • Large ID connections reduce clogging when sulfur precipitates out
17132F-2 2 ±0.01 1
and deposits on the inside of connectors
17132F-5 5 ±0.01 1
17132F-10 10 ±0.02 1 • Supplied with a size 4 glass stopcock in the bottom,
a size 2 stopcock in the top and a size 13 glass
pennyhead stopper
• Designed for use with method UOP 9-85
• Manufactured from 33 expansion, low extractable
Serialized and Certified Funnel Top Micro Buret with borosilicate glass conforming to USP Type I and
Straight Bore PTFE Stopcock ASTM E438, Type I, Class A requirements
Used for small volume titrations requiring traceable volumetric accuracy.
Kimble Chase Capacity Tolerance: Case
Cat. No. (mL) Buret (mL) Qty
• Precision bore buret is permanently marked with an individual serial
number and is traceable to NIST standards 30034A-100 100 ±0.2 1
• Supplied with a Certificate of Graduation Accuracy
• Easy-to-read durable white ceramic enamel scale Neutral Oil and Loss Columns
• Funnel top accepts a one-hole #3 rubber stopper Apparatus for the determination of total neutral oil of natural fats and oils
• Replacement 2 mm straight bore stopcock plug is consisting of triglycerides and unsaponifiable matter.
821001-0002.
• Supplied with a chemically-resistant, self-lubricating • Unique design of the flask allows the transfer of the weighed sample
PTFE stopcock plug directly onto the column
• Manufactured to the specifications found in ASTM E694 • Supplied complete, as shown
• Calibrated to the accuracy requirements found in ASTM • Stopcocks have PTFE plugs, and the column has a 40-
Specification E542 60 micron porosity fritted disc
• Ref: ASTM Method D974 • Joints are Standard Taper 19/22 except for the extension
• Manufactured from 33 expansion, low extractable tube, which is Standard Taper 7/25
borosilicate glass conforming to USP Type I and ASTM • Ref: OACS Official Method Ca9f-57, JAOCS Vol. 46, No.
E438, Type I, Class A requirements 5, Pages 252-255
• Manufactured from 33 expansion, low extractable
A short length of glass tubing aids in filling the buret through borosilicate glass conforming to USP Type I and ASTM
the tip by vacuum if desired. Stopper and tubing are not E438, Type I, Class A requirements
supplied.
Kimble Chase Capacity Tolerance Case Free fatty acids and miscellaneous non-fat substances are
Cat. No. (mL) (mL) Qty removed by passing the sample through a column of activated
17110F-5 5 ±0.01 1
alumina. Losses are then calculated.
17110F-10 10 ±0.02 1
Kimble Chase Solvent Reservoir Porosity Case
Cat. No. Capacity (mL) (microns) Qty
427100-0000 175 40-60 1
8 7
Friedrich Condenser with Hose Connection Sidearm Allihn Condensers with Full Length Joints
Friedrich condenser used primarily in reflux mode and Soxhlet Used in many refluxing operations.
extractions.
• Standard Taper drip joint at bottom and a Standard Taper
• Water inlet and outlet located above ring-sealed inner condensing outer joint at top
tube • Manufactured from 33 expansion, low extractable
• Standard Taper inner drip joint and side outlet for borosilicate glass conforming to USP Type I and ASTM
drying tube, etc E438, Type I, Class A requirements
• Molded inner spiral provides surface area for the
condensation of the product
Kimble Chase Overall Height Standard Case
• Manufactured from 33 expansion, low extractable Cat. No. (mm) Taper Joints Qty
borosilicate glass conforming to USP Type I and 431000-2420 370 24/40 1
ASTM E438, Type I, Class A requirements 431000-2425 425 24/40 1
431000-2430 470 24/40 1
Kimble Chase Cold Finger Standard Taper Case
431000-2440 570 24/40 1
Cat. No. Length (mm) Joints Qty
431000-2920 380 29/42 1
456250-0021 190 34/45 1 431000-2930 480 29/42 1
456250-0022 190 45/50 1
456250-0023 190 55/50 1
8 8
West Condenser with Full Length 24/40 Joints Class B Cylinders with Pour Spout
The narrow annular space of the West design provides The primary function of this TC cylinder is to receive liquids where
high cooling efficiency due to the increased flow rate of the volumetric calculations are based solely on the volume contained within
cooling medium. the cylinder.
• Full length 24/40 joints
• Standard Taper outer joint at the top and Standard • Among other applications, TC cylinders are frequently used as
Taper inner drip joint at the bottom receivers for the condensate from distillation procedures and
• Manufactured from 33 expansion, low extractable sedimentation values of precipitates
borosilicate glass conforming to USP Type I and ASTM • “TC” appears on each cylinder and indicates the cylinder is
E438, Type I, Class A requirements calibrated to contain
Kimble Chase Jacket Standard Case • 10 mL size has an enlarged funnel top for ease of filling
Cat. No. Length (mm) Taper Joints Qty • Ref: ASTM Method D86, D892
452000-2410 100 24/40 1 • Provided with a hexagonal base flat ground for stability and a SAFE-
452000-2420 200 24/40 1
452000-2430 300 24/40 1 GARD® bumper on sizes 25 mL and larger
• Designed from ASTM E1272, Style I, Class B requirements
• Manufactured from 33 expansion, low extractable borosilicate
glass conforming to USP Type I and ASTM E438, Type I, Class A
requirements
Class A Measuring Cylinders
• Letters “TC” on cylinder indicate to contain Kimble Chase Capacity Graduation Tolerance Case
Cat. No. (mL) Range (mL) (mL) Qty
• Pour spout
20022-10 10 1 to 10 ±0.1 12
• SAFE-GARD® bumper is supplied 20022-25 25 3 to 25 ±0.3 1
• Manufactured from 33 expansion, low extractable borosilicate 20022-50 50 3 to 50 ±0.4 12
glass conforming to USP Type I and ASTM E438, Type I, Class A 20022-100 100 5 to 100 ±0.6 12
20022-250 250 10 to 250 ±1.4 6
requirements 20022-500 500 25 to 500 ±2.6 4
Graduation 20022-1000 1000 50 to 1000 ±5.0 4
Kimble Chase Capacity Tolerance Case 20022-2000 2000 100 to 2000 ±10.0 2
Intervals
Cat. No. (mL) (mL) Qty
(mL)
20027-10 10 0.1 ±0.80 6
20027-25 25 0.2 ±0.14 6
20027-50 50 1 ±0.2 6
20027-100 100 1 ±0.35 6
20027-250 250 2 ±0.65 4 Class B Cylinders with Single Metric Scale and Red
20027-500 500 5 ±1.10 4 Stripe
20027-1000 1000 10 ±2.00 1
20027-2000 2000 20 ±6.00 1
• “TD” appears on each cylinder and indicates the cylinder is
calibrated to deliver
• SAFE-GARD® bumpers are supplied with sizes 25 through 2000
Class A Cylinders with Reverse Graduations mL
KIMAX® Class A cylinder is marked with a reverse metric scale. • The 10 mL size has an enlarged funnel-shaped top for ease of filling
• Designed from ASTM Specification E1272, Style I, Class B
• “TD” appears on each cylinder and indicates the cylinder is requirements
calibrated to deliver • Manufactured from 33 expansion, low extractable borosilicate
• SAFE-GARD® bumpers are supplied with sizes 25mL through glass conforming to USP Type I and ASTM E438, Type I, Class A
2000 mL requirements
• Manufactured from 33 expansion, low extractable borosilicate glass Kimble Chase Capacity Graduation Tolerance Case
conforming to USP Type I and ASTM E438, Type I, Class A Cat. No. (mL) Range (mL) (mL) Qty
requirements 20024D-10 10 1 to 10 ±0.1 24
20024D-25 25 2 to 25 ±0.3 24
Kimble Chase Capacity Graduation Tolerance Case 20024D-50 50 3 to 50 ±0.4 24
Cat. No. (mL) Range (mL) (mL) Qty 20024D-100 100 5 to 100 ±0.6 24
20028W-10 10 1 to 10 ±0.09 6 20024D-250 250 10 to 250 ±1.4 12
20028W-25 25 2 to 25 ±0.17 6 20024D-500 500 25 to 500 ±2.6 8
20028W-50 50 3 to 50 ±0.25 6 20024D-1000 1000 50 to 1000 ±5.0 4
20028W-100 100 5 to 100 ±0.40 6 20024D-2000 2000 100 to 2000 ±10.0 4
20028W-250 250 10 to 250 ±0.80 4
20028W-500 500 25 to 500 ±1.30 4
20028W-1000 1000 50 to 1000 ±2.50 1
20028W-2000 2000 100 to 2000 ±6.00 1
8 9
Class B Cylinders for Emulsion Test
KIMAX® cylinder used in the determination of emulsifying and Dean Stark Distillation Receivers
demulsifying tendencies of lubricating oils (ASTM D1401). Ideally suited for the determination of water content in organic solvents.
• “TC” appears on each cylinder and indicates the cylinder is • Dean Stark design for solvents that are classified as either heavier
calibrated to contain than water or lighter than water
• Round base to fit baths in which this cylinder is generally used • Unit is compact in both the Standard Taper 24/40 and Standard
• Pour spout Taper 14/20 sizes
• Ref: ASTM Method D1401 • Lower three-way stopcock provides a sample port, and the
• Scale is durable white ceramic enamel apparatus can be drained without disassembly
• Manufactured from 33 expansion, low extractable • Trap area is positioned well above the boiling flask
borosilicate glass conforming to USP Type I and ASTM • Thermometer joint is Standard Taper 10/30.
E438, Type I, Class A requirements Stopcock plug is 822501-0002
• Ref: Design suggested by Dr. A. J. East, Celanese
Kimble Chase Capacity Tolerance Case Corp
Cat. No. (mL) (mL) Qty
• Manufactured from 33 expansion, low extractable
20011-100 100 ±1.0 1
borosilicate glass conforming to USP Type I and
ASTM E438, Type I, Class A requirements
Class B Cylinders with Single Metric Scale and Glass
Stopper
The 250 mL size may be used to determine unsaponified matter in soaps Kimble Chase Capacity Graduation Intervals Case
and soap products (ASTM D460), and anhydrous salt free soda soap Cat. No. (mL) (mL) Qty
and fatty matter in soaps containing synthetic detergents (ASTM D820). 535801-0000 20 0-3 in 0.2, 3-20 in 0.5 1
The 500 mL size may be used in settlement tests of emulsified asphalts
(ASTM D244).
• KIMAX® cylinder with durable white ceramic enamel scale Modified Dean Stark Distillation Receiver
• Letters “TC” on cylinder indicate to contain • KIMAX® distilling receiver with full length Standard Taper 24/40
• The 10 and 25 mL sizes are comparatively short to provide in- joints and a siphon return arm
creased stability • Ref: ASTM Method D95
• Standard Taper glass stopper is supplied • Sidearm bridge equalizes pressure
• Heights given below do not include the stopper • Designed from ASTM Specification E123, Style A
• Replacement stopper is 850100 • Manufactured from 33 expansion, low extractable borosilicate glass
• Designed from ASTM Specification E1272, Style II, Class B require- conforming to USP Type I and ASTM E438, Type I,
ments Class A requirements
• Ref: ASTM Methods D244, D1094 Kimble Chase Capacity Case
Tolerance (mL)
• Manufactured from 33 expansion, low extractable borosilicate Cat. No. (mL) Qty
glass conforming to USP Type I and ASTM E438, Type I, Class A ±0.05 (1st set of sub-
22012-10 10 divisions), ±0.1 (2nd 1
requirements
set of subdivisions)
Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty
20039-50 50 ±0.4 24
20039-100 100 ±0.6 24
20039-250 250 ±1.4 8
20039-500 500 ±2.6 6 Bidwell-Sterling Moisture Test Distillation Receiver
20039-1000 1000 ±5.0 4 Bidwell-Sterling designed for the determination of moisture in foods and
20039-2000 2000 ±10.0 2
organics.
8 10
General Distillation Apparatus
KIMAX® apparatus used in general purpose distillation and phenol
Engler Distilling Flasks with Three Reference Lines
distillation.
For use with Haage automatic distillation apparatus or others that call for
three thermometer depth insertions.
• Flask has a flat bottom and a distillation head with a 19/38 joint
• Supplied with a Standard Taper stopper
• Sidearm tube is sealed at an angle of 75° from the neck and is 137
• Condenser is Graham-style, having a 200 mm jacket with a 19/38
± 3 mm from the bottom of the flask three reference lines
joint at the top only
• Ref: ASTM D86
• For method, reference APHA Examination of Water and
• Manufactured from 33 expansion, low extractable
Wastewater: Method 4500-NH3 nitrogen (ammonia) in purified
borosilicate glass conforming to USP Type I and
drinking water, natural water, and highly purified wastewaters
ASTM E438, Type I, Class A requirements
(concentration < 20 μg/L)
• Method calls for use with tall form 50 mL Nessler Tubes (45315A &
Kimble Chase Capacity Arm OD Case
B-50) Cat. No. (mL) (mm) Qty
• Manufactured from 33 expansion, low extractable borosilicate glass 26016-125 125 7 24
conforming to USP Type I and ASTM E438, Type I,
Class A requirements
Kimble Chase Capacity Case
Cat. No. (mL) Qty
21500-500 500 1
21500-1000 1000 1
Barrett Distilling Flasks
• Barrett flasks made to ASTM E133 specifications
• These flasks feature smooth, consistent, heavy walls for uniform
Engler Distilling Flasks heating and minimal breakage
KIMAX® distilling flask. • Supplied with one cork for the sidearm
• Manufactured from 33 expansion, low extractable borosilicate glass
• Sidearm tube is sealed at an angle of 75° from the neck and is 137 conforming to USP Type I and ASTM E438, Type I,
± 3 mm from the bottom of the flask Class A requirements
• Designed from ASTM Specification E133 and intended for use in Kimble Chase Capacity Case
Type
ASTM D86, D233, D801, and D802 Cat. No. (mL) Qty
610910-0125 125 Engler 12
• Ref: ASTM Method D86
610900-0200 200 Barrett 24
• Manufactured from 33 expansion, low extractable
borosilicate glass conforming to USP Type I and
ASTM E438, Type I, Class A requirements
Kimble Chase Capacity Arm OD Case
Cat. No. (mL) (mm) Qty
26015-125 125 7 24
Thermometer Centering Device
Designed for 6.5 mm OD manual thermometer or
1/4” temperature sensor probe as used on standard
Automated Distillation Apparatus with Kimble
Engler Distilling Flasks with 19/22 Standard Taper 26015-125 flasks.
Joint
KIMAX® distilling flask.
• Fits glassware designed for rubber stopper size
2
• Sidearm tube is sealed at an angle of 75° from the neck and is 137
• PTFE body with FKM o-ring seal assures
± 3 mm from the bottom of the flask
proper centering of sensor probe in flask neck
• 19/22 Standard Taper Joint
• Cap material is yellow polypropylene
• Manufactured from 33 expansion, low extractable
• Ref: ASTM Method D86
borosilicate glass conforming to USP Type I and
ASTM E438, Type I, Class A requirements Kimble Chase Case
Body OD (mm)
Cat. No. Qty
Kimble Chase Capacity Arm OD Case 26015C-125 6.5 1
Cat. No. (mL) (mm) Qty
26015G-125 125 7 24
8 11
Class A Volumetric Flasks with Polyethylene Stopper Serialized and Certified Class A Volumetric Flasks
with Pennyhead Glass Stoppers
• KIMAX® flask with a graduation ring blasted on the neck Volumetric flasks are ideal for measuring accurate volumes of liquids.
• Calibrated to contain
• With a marking spot on sizes 10 mL and larger • KIMAX® flask is permanently marked with an individual serial
• Supplied with a 28160R polyethylene stopper to fit in the Standard number and supplied with a Certificate of Graduation Accuracy.
Taper ground neck • Graduation ring is blasted on the neck
• Enlarged top of the stopper will protect the neck if the flask is tipped • Letters “TC” on the flask indicate to contain
over • Supplied with a marking spot and a Standard Taper ground glass
• Manufactured from 33 expansion, low extractable borosilicate stopper
glass conforming to USP Type I and ASTM E438, Type I, Class A • These flasks have been carefully selected to meet the requirements
requirements for accuracy, appearance, glass quality, calibration line, and
Kimble Chase Capacity Tolerance Case inscriptions of former NBS Circular 602
Cat. No. (mL) (mL) Qty • Designed from ASTM Specification E288, Class A serialized
28014P-5 5 ±0.02 12
requirements
28014P-10 10 ±0.02 12
28014P-25 25 ±0.03 12 • Manufactured from 33 expansion, low extractable borosilicate
28014P-50 50 ±0.05 12 glass conforming to USP Type I and ASTM E438, Type I, Class A
28014P-100 100 ±0.08 12 requirements
28014P-200 200 ±0.10 12
28014P-250 250 ±0.12 12 Kimble Chase Capacity Tolerance Case
28014P-500 500 ±0.20 12 Cat. No. (mL) (mL) Qty
28014P-1000 1000 ±0.30 6 28017-10 10 ±0.02 12
28014P-2000 2000 ±0.50 4 28017-25 25 ±0.03 12
28017-50 50 ±0.05 12
28017-100 100 ±0.08 12
28017-200 200 ±0.10 12
28017-250 250 ±0.12 12
28017-500 500 ±0.20 12
Serialized and Certified Class A Micro Volumetric 28017-1000 1000 ±0.30 6
Flasks with Glass Stopper 28017-2000 2000 ±0.50 4
Volumetric flasks are ideal for measuring accurate volumes of liquids.
8 12
Class A Volumetric Flasks with Color-Coded PTFE
Stopper
• KIMAX® flask with a graduation ring blasted on the neck
• Calibrated to contain
• With a marking spot on 10 mL and larger sizes
Jointed, Narrow Mouth Erlenmeyer Flasks with
• The 2 mL size is test tube-shaped. All other sizes are of a
Capacity Scale
• Flasks have 24/40 standard taper joint except for 50 mL flask,
conventional flask shape
which has a 19/38 standard taper joint
• Supplied with a PTFE Standard Taper stopper which has a color-
• With capacity scale
coded handle
• KIMAX® flask with a full length Standard Taper ground glass neck
• Replacement stopper is 41901R
finish
• The 5 mL and larger sizes are designed from ASTM Specification
• Ref: ASTM Method D94
E288, Class A requirements
• Designed from ASTM Specification E1404, Type II, Class I
• Manufactured from 33 expansion, low extractable borosilicate
requirements
glass conforming to USP Type I and ASTM E438, Type I, Class A
• Manufactured from 33 expansion, low extractable borosilicate
requirements
glass conforming to USP Type I and ASTM E438, Type I, Class A
Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty requirements
28014F-2 2 ±0.015 12
28014F-5 5 ±0.02 12 Kimble Chase Capacity Graduation Case
28014F-10 10 ±0.02 12 Cat. No. (mL) Range (mL) Qty
28014F-25 25 ±0.03 12 26510-50 50 20 to 50 12
28014F-50 50 ±0.05 12 26510-125 125 50 to 125 12
28014F-100 100 ±0.08 12 26510-250 250 50 to 225 12
28014F-200 200 ±0.10 12 26510-500 500 100 to 500 12
28014F-250 250 ±0.12 12 26510-1000 1000 250 to 1000 12
28014F-500 500 ±0.20 12 26510-2000 2000 600 to 2000 1
28014F-1000 1000 ±0.30 6
28014F-2000 2000 ±0.50 4
8 13
Flat Bottom Short Neck Boiling Flask
Wide Mouth Erlenmeyer Flasks • KIMAX® boiling flask with a short Standard Taper joint neck.
• Heavy-duty tooled-top finish with capacity scale • Designed from ASTM Specification E1403, Type I, Class IV
• KIMAX® flask with a wide mouth. requirements
• Designed from ASTM Specification E1404, Type I, Class II • Manufactured from 33 expansion, low extractable borosilicate
requirements glass conforming to USP Type I and ASTM E438, Type I, Class A
• Ref: ASTM Method D473 requirements
• Manufactured from 33 expansion, low extractable borosilicate
Kimble Chase Capacity Body OD Case
glass conforming to USP Type I and ASTM E438, Type I, Class A Cat. No. (mL) (mm) Qty
requirements 25055-125 125 65 12
Kimble Chase Capacity Graduation Range Case 25055-250 250 83 12
Cat. No. (mL) (mL) Qty 25055-300 300 87 12
26650-125 125 50 to 125 48 25055-500 500 102 12
26650-250 250 50 to 225 48 25055-1000 1000 130 12
26650-500 500 100 to 500 36
26650-1000 1000 250 to 1000 24
26650-2000 2000 600 to 2000 8
Round Bottom Short Neck Flask
• KIMAX® boiling flask with a round bottom
• 25276 series has a medium length Standard Taper 14/20 joint
Graduated Filtering Flask with Side Tubulation • 25277 series has a medium length Standard Taper 19/22 joint
KIMAX® flask with side tubulation. • 25285 series has a full length Standard Taper 24/40 joint
• Designed from ASTM Specification E1403, Type II, Class III
• Capacity scale requirements
• Flasks are designed for vacuum to 29” of mercury • Ref: ASTM Method D322
• Made with a heavier wall than a standard Erlenmeyer flask • Manufactured from 33 expansion, low extractable borosilicate
• All sizes have side hose connection designed to accept 5/16 inch ID glass conforming to USP Type I and ASTM E438, Type I, Class A
flexible tubing requirements
• Manufactured from 33 expansion, low extractable borosilicate Kimble Chase Capacity Body OD Case
Cat. No. (mL) (mm) Qty
glass conforming to USP Type I and ASTM E438, Type I, Class A
25276-100 100 63 12
requirements 25276-250 250 82 12
Kimble Chase Capacity Graduation Range Case 25277-100 100 63 12
Cat. No. (mL) (mL) Qty 25277-250 250 82 12
27060-25 25 5 to 25 18 25277-500 500 102 12
27060-50 50 20 to 50 18 25285-50 50 48 12
27060-125 125 50 to 125 18 25285-100 100 63 12
27060-250 250 50 to 250 18 25285-200 200 75 12
27060-500 500 150 to 500 18 25285-250 250 83 12
27060-1000 1000 300 to 1000 12 25285-300 300 88 12
27060-2000 2000 600 to 2000 1 25285-500 500 102 12
27060-4000 4000 1000 to 4000 1 25285-1000 1000 130 12
25285-2000 2000 161 6
25285-3000 3000 185 6
8 14
Single Standard Taper Neck Round Bottom Flask
• Single neck flask with a Standard Taper outer joint 1-1/2” Stem Powder Addition Funnels
• Ref: ASTM Method D95 • KIMAX® funnel with a short, wide stem
• Manufactured from 33 expansion, low extractable borosilicate glass • Constructed with a heavy uniform wall and a strong, fire-polished rim
conforming to USP Type I and ASTM E438, Type I, and stem to provide a long service life
Class A requirements • Funnel has a high resistance to chemical attack and mechanical and
thermal shock
Kimble Chase Capacity Body OD Case • Designed from ASTM Specification E1095, Type IV requirements
Cat. No. (mL) (mm) Qty
• Manufactured from 33 expansion, low extractable borosilicate
601000-0124 50 48 1
601000-0129 50 48 1 glass conforming to USP Type I and ASTM E438, Type I, Class A
601000-0224 100 64 1 requirements
Kimble Chase ID at Funnel Length of Case
Cat. No. Top (mm) Stem (mm) Qty
Short Stem Addition Funnels 29020-60 60 35 24
This KIMAX® funnel is constructed with heavy uniform walls, molded 29020-80 80 35 24
rims and fire-polished stems to give a long service life. 29020-100 100 35 24
29020-125 125 35 12
29020-150 150 35 12
• Funnels have a high resistance to chemical attack and mechanical
and thermal shock
• A piece of filter paper, when folded to form the filtering cone, forms a
precise 60° angle. If the funnel is also 60°, as are the vast majority,
then the only effective filtering area is down near the tip
• The exclusive KIMAX® 58° funnel promotes faster, more effective Oxidation Cell
filtering because the cone is suspended by its uppermost edge, Used in the measurement of inherent stability of middle
leaving most of the conical area for filtration distillate petroleum fuel under accelerated oxidizing
• Designed from ASTM Specification E1095, Type I, Class A conditions.
requirements
• Manufactured from 33 expansion, low extractable borosilicate • The cell consists of a test tube, a condenser and an
glass conforming to USP Type I and ASTM E438, Type I, Class A oxygen delivery tube
requirements • Ref: ASTM D943 and D2274
Kimble Chase ID at Funnel Length of Case • Manufactured from 33 expansion, low extractable
Cat. No. Top (mm) Stem (mm) Qty borosilicate glass conforming to USP Type 1 and ASTM
28950-25 25 40 24 E438, Type I, Class A requirements
28950-35 35 50 24
28950-45 45 50 24 Kimble Chase Overall Height OD Case
28950-55 55 63 48 Cat. No. (mm) (mm) Qty
28950-65 65 63 48 896600-0000 600 45 1
28950-75 75 75 48
28950-90 90 97 24
28950-100 100 97 24
8 15
Petrochemical Filter Stick Apparatus with Hooks and
Springs
• Apparatus used in the determination of oil content
and solvent extractables in petroleum waxes.
• Assembly consists of a sintered glass filter stick Ramsbottom Coking Bulb
with air pressure inlet tube and delivery nozzle and The Ramsbottom Coking Bulb is used in the determination of carbon
a cooling tube with 24/40 joints residue in petroleum products.
• Supplied with one pair of springs
• Ref: ASTM D721
• Manufactured from 33 expansion, low extractable • Ref: ASTM D524
borosilicate glass conforming to USP Type I and • Manufactured from 33 expansion, low extractable
ASTM E438, Type I, Class A requirements borosilicate glass conforming to USP Type I and
Kimble Chase Standard Case ASTM E438, Type I, Class A requirements
Cat. No. Taper Joints Qty Kimble Chase Overall OD Case
513880-0000 24/40 1 Cat. No. Height (mm) (mm) Qty
896650-0000 57 25 6
Unserialized Reusable To Deliver Volumetric Class A
Pipets
• Calibrated To Deliver (TD)
Saybolt Viscosity, Volumetric Flask, Class A
• Color coded
• Designed from ASTM Specification E969, Class A requirements
• 75 and 200 mL sizes are designed from ASTM E542 KIMAX® flask used in determining Saybolt viscosity of petroleum and
• Manufactured from 51 expansion borosilicate glass conforming to bituminous materials as described in ASTM test methods D88 and E102.
USP Type I and ASTM E438, Type I, Class B requirements Made with heavy walls and a reinforced top. Graduation ring is blasted on
Kimble Chase Capacity Tolerance Case the neck. Calibrated to contain. With marking spot.
Cat. No. (mL) (mL) Qty
37004-1 1 ± 0.006 12
37004-1510 1.5 ± 0.006 12
37004-2 2 ± 0.006 12 Kimble Chase Capcity ± Tolerance Case
37004-2510 2.5 ± 0.006 12 Cat. No. (mL) (mL) Qty
37004-3 3 ± 0.01 12 28126-60 * 60 0.05 1
37004-4 4 ± 0.01 12
37004-5 5 ± 0.01 12
37004-6 6 ± 0.01 6
37004-7 7 ± 0.01 6
37004-8 8 ± 0.01 6 Gas Measuring Tubes
37004-9 9 ± 0.02 6
KIMAX® gas measuring tube closed at the zero end for gas
37004-10 10 ± 0.02 12
37004-12 12 ± 0.02 12 measurement.
37004-15 15 ± 0.03 12
37004-20 20 ± 0.03 12 • Durable black ceramic enamel scale
37004-25 25 ± 0.03 12
37004-30 30 ± 0.03 6 • Without stopcock
37004-40 40 ± 0.05 6 • Manufactured from 33 expansion, low extractable
37004-50 50 ± 0.05 12 borosilicate glass conforming to USP Type I and ASTM
37004-75 75 ± 0.05 6
E438, Type I, Class A requirements
37004-100 100 ± 0.08 12
37004-200 200 ± 0.16 6
37004-510 0.5 ± 0.006 12 Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty
Reusable Class B Mohr Style Color-Coded TD Pipets 30060-50 50 ± 0.10 1
Designed with small tip openings for chemical laboratory work.
• Calibrated to deliver (TD)
• Scale is permanent brown stain fused into uniform bore
tubing without etching
Gas Sampling Tubes with Glass Plugs and
• Pipet is graduated to a base line which is on the straight
tube above the taper Plain Ends
• Color-coded for ease in sorting and selecting the correct KIMAX® gas collecting tube with tubulations on each end of
size pipet the tube.
• Manufactured from 51 expansion borosilicate glass
conforming to USP Type I and ASTM E438, Type I, Class
• Tubulations accept 3/8 inch ID tubing
B requirements
• Manufactured from 33 expansion, low extractable
Kimble Chase Capacity Tolerance Case
Cat. No. (mL) (mL) Qty borosilicate glass conforming to USP Type I and ASTM
37020-110 0.1 ± 0.005 12 E438, Type I, Class A requirements
37020-1110 1 ± 0.02 12 Kimble Chase Capacity Standard Taper Case
37020-11100 1 ± 0.02 12 Cat. No. (mL) Stopcock Size Qty
37020-2 2 ± 0.02 12
30040-500 500 4 1
37020-5 5 ± 0.04 12
37020-10 10 ± 0.06 12
37020-25 25 ± 0.10 12
37020-50 50 ± 0.16 8
8 16
API Graduated Centrifuge Tubes
Used to determine the bottom sediment and water in petroleum.
• KIMAX® tube with a long taper Pear-Shaped Centrifuge Tubes with White
• Calibrated to contain Scale
• Scale, legend and marking spot are durable white ceramic enamel KIMAX® tube used in the determination of bottom sediment
• Referred to as the “finger” tube and water in petroleum products.
• Made in accordance with the former specifications of the American
Petroleum Institute (API Standard 2542) • Calibrated to contain
• Manufactured from 33 expansion, low extractable borosilicate • Stem diameter holds 1.5 mL
glass conforming to USP Type I and ASTM E438, Type I, Class A • Scale and legend are durable white ceramic enamel
requirements • Manufactured from 33 expansion, low extractable borosilicate
Graduation Intervals (%): Tolerance (%): glass conforming to USP Type I and ASTM E438, Type I, Class A
0-3 in 0.2 0 to1 – 0.10 requirements
Above 1 to 2 – 0.15 45244-100
8 17
8” Oil and Weathering (End Point Index) Centrifuge
8” Oil Centrifuge Tubes Tubes
KIMAX® tube used in the determination of water and sediment in crude Can be used in the determination of residues in Liquified Petroleum (LP)
mineral oils, fuel oils and other petroleum products (D1796 and MPMS gases, ASTM Method D2158.
10.4 standards); in determination of volume of precipitate formed by • KIMAX® tube used extensively in California
centrifuging definite quantities of steam cylinder stocks and black oils • Calibrated to contain
and other lubricating oils (ASTM D91 and D128); and in testing for acidity • Different graduations than 45240
of distillation residues or hydrocarbon liquids of gasoline or petroleum • Scale and legend are durable white ceramic enamel
solvents (ASTM D1093). • Top is tooled to accept snap cap 28150R-6
• Ref: ASTM Method D2158
• Calibrated to contain • Manufactured from 33 expansion, low extractable borosilicate glass
• Scale and legend are durable white ceramic enamel conforming to USP Type I and ASTM E438, Type I, Class
• Top is tooled to accept snap cap 28150R-6 A requirements
• Referenced in ASTM D4007, D91, D1796, D1093 Kimble Chase Capacity Case
• Manufactured from 33 expansion, low extractable Graduation Intervals (mL)
Cat. No. (mL) Qty
borosilicate glass conforming to USP Type I and ASTM 0-1 in 0.05, 1-3 in 0.1, 3-6
E438, Type I, Class A requirements 45241-100 100 in 0.2, 6-10 in 0.5, 10-100 12
in 1
Kimble Chase Capacity Case
Graduation Intervals (mL)
Cat. No. (mL) Qty
0-0.5 in 0.05, 0.5-2 in 0.1,
45240-100 100 2-3 in 0.2, 3-5 in 0.5, 5-10 in 12 Soil Analysis Tube
1, 10-25 in 5, 25-100 in 25 These tubes are designed for use with Teledyne Tekmar 2016/2032
Autosamplers and 4100/4200 Automatic Samplers that are equipped with
3/4” diameter mounts.
6” Short Cone Oil Centrifuge Tubes
KIMAX® tube designed for field use in testing petroleum.
• The larger opening of these disposable tubes permits easier sample
loading and facilitates the weighing of solid and soil samples
• Calibrated to contain
• Manufactured from 33 expansion, low extractable
• Scale and legend are durable white ceramic enamel
borosilicate glass conforming to USP Type I and ASTM
• 45243-200 is graduated in %. 100 mL equals 200%
E438, Type I, Class A requirements
• Top is tooled to accept snap cap 28150R-6
• Referenced in ASTM D4007 Kimble Chase Length Case
OD (mm)
Cat. No. (mm) Qty
• Manufactured from 33 expansion, low extractable borosilicate
591175-0715 19 150 24
glass conforming to USP Type I and ASTM E438, Type I, Class A
requirements
Kimble Chase Capacity Case Cannon-Fenske Uncalibrated Serialized Viscometer
Graduation Intervals (mL)
Cat. No. (mL) Qty Tubes
0-0.5 in 0.05, 0.5-2 in 0.1, Cannon-Fenske uncalibrated viscometer tube for use in obtaining
45243-100 100 2-3 in 0.2, 3-5 in 0.5, 5-10 in 12
kinematic viscosities of transparent liquids (ASTM Method of Test D445).
1, 10-25 in 5, and at 50, 100
0-0.1% in 0.10%, 1-4 in
0.20, 4-6 in 0.40, 6-10 in 1, • KIMAX® tube designed from ASTM Specification D446
45243-200 200 6
10-20 in 2, 20-50 in 10, and • Permanently marked with an individual serial number
at 100, 200
• Viscosity ranges shown below are for an efflux time greater than
200 seconds
California Centrifuge Tube with Red Stripe • Lines and legend are printed black
KIMAX® conical bottom centrifuge tube is used for testing of • Ref: ASTM Method D445
petroleum products according to ASTM D91, D893 and D1796. • Manufactured from 33 expansion, low extractable
borosilicate glass conforming to USP Type I and
• Tube has a permanent red stripe under the white enamel ASTM E438, Type I, Class A requirements
graduations for easy reading of results
• Scale and legend are durable white ceramic enamel Calibration against a standard liquid of known viscosity
• Top is tooled to accept snap cap 28150R-6 or against a second viscometer with a known constant
• Manufactured from 33 expansion, low extractable borosilicate must be made before use.
glass conforming to USP Type I and ASTM E438, Type I, Class A Kimble Chase Approximate Kinematic Case
Size
requirements Cat. No. Constant Centistokes Qty
KIMBLECHASE Capacity Case 46460-50 0.004 0.8 to 4 50 1
Graduation Intervals (mL) 46460-100 0.015 3 to 15 100 1
Cat. No. (mL) Qty
0-0.5 in 0.05, 0.5-2 in 0.1, 46460-150 0.035 7 to 35 150 1
2-3 in 0.2, 3-5 in 0.5, 5-10 46460-200 0.1 20 to 100 200 1
45239-100 100 12 46460-300 0.25 50 to 250 300 1
in 1, 10-25 in 5, and at
46460-350 0.5 100 to 500 350 1
50, 75, 100
46460-400 1.2 240 to 1200 400 1
8 18
ASTM METHODS
8 19
We’re here to help!
If you don’t find what you need, please call for
assistance. Our customer service group will be
glad to discuss your special requirements.
PETROCHEMICAL
SOLUTIONS
For additional product, technical, or distributor information, please visit www.kimble-chase.com or call 800.451.4351. Customers outside the
United States, please call: +1.865.717.2600 Ext. 1 or contact your local Kimble Chase sales office listed below.
KIMAX®, KIM-KAP®, SAFE-GARD®, and RAY-SORB® are registered trademarks of Gerresheimer Glass Inc. All trademarks are the property of their
respective owners. Specifications are subject to change without notice. Printed in the U.S.A. 20140601KC-1259