Professional Documents
Culture Documents
Downloaded From Manuals Search Engine
Downloaded From Manuals Search Engine
MAINTENANCE CHART
8. Starting System
Check recoil
starter. Operation.
. .
Regular maintenance is most impor-
tant for the best performance and
9.* Decarbonization More frequently
if necessary.
.
safe operation. 10. Auger Gear Oil Replace . .
Check damage.
Pre-Ope- Initial Every
ration 3 Before
11. Skid/Scraper Adjustif .
No. Item Remarks 1 month necessary.
check months Storage season
or 20 Hr
Check condition
(daily) or 50 Hr
12.* Auger
Check shear bolt
damage.Replace
itifnecessary.
. . . .
1. Spark Plug
adjust gap and . . Check deflection/
clean. Replace if
necessary . 13. DriveTrack/
Wheel
air pressure. . . .
Check oil level . Ajustif
necessary.
2. EngineOil
Replace
Clean fuel cock
. . 14.* DriveBelt Check damage . .
3. Fuel Filter and fuel tank
filter. Replace if
. 15. Lubrication
Lubricatewith
greaseor
SAE 5W30 oil.
.
necessary. Check all fittings
4.* Valve Clearance
Check and adjust
when engine is
cold.
. 16.* Fittings/
Fasteners
and fasteners.
Correct if
necessary.
.
Check fuel hose
5.* Fuel Line for crack or
damage.Replace
. *: It is recommended that these items be
serviced by a Yamaha dealer or other
qualified mechanic.
if necessary.
Checkforleakage.
6.* Exhaust System Retighten or
replace gasket if
.
necessary.
Check choke
7. Carburetor (Control lever) .
operation.
-29- -30-
G-520 8-561
CD Upper level
<Z) Lower level
Be sure no foreign material
-31- -32- enters the crankcase.
l
·
Be sure the main switch key
and spark plug lead are re-
moved or disconnected
fore replacement.
be-
NOTE:
Drain Plug:
31 Nm (3.1 m-kg,
22.4 ft-Ib)
-
ding gear oil.
case. Remove the oil drain plug · Be sure the machine is se-
so that the oil can be complete- curely placed.
ly drained.
2. Check the drain plug gasket. If
damaged, replace it. 8-586
-33- -34-
II NOTE:
NOTE: · Lower the foot pedal position to .
...
.11 · Use the standard clearance for increase the auger height.
smooth concrete or asphalt · Shift the foot pedal to a lower
roads. position when reversing the
· Increase the clearance for stone machine.
or gravel roads. Free Position
..
1. Raise or lower the handlebar to
adjust the auger height.
8-590
CD Scraper
Replace the auger shear bolts when
!I (2) Scraper height
<ID Level surface the auger does do not rotate even
3 ~m
(3).4=.... though the impeller is rotating.
II
- T :~:~:~
NOTE:
1. Remove the snow caught on the
· Use the standard height for
auger.
11
smooth concrete or asphalt
roads. .
..
2. Remove the broken shear bolts.
.EJ · Increase the height for stone or
gravel roads.
3. Install the new shear bolts on the
auger and auger shaft.
3. Tighten the scraper bolts and
nuts. NOTE:
Use the spare shear bolts in your tool
NOTE: kit.
Be sure the scraper edge is parallel
to the level surface.
-37- -38-
Measure the tracks vertical deflec- 2. Remove the under plate and
lubricate the transmission shaft
tion by adding 5 kg (11 Ib) of force as shown.
at the center of track.
CD Deflection
~ 5 kg (11 Ib) force
Do not grease shaft excessively
as excess grease may be thrown
Standard Track Deflection: onto drive wheels.
YS624TM
8.5-12 mm
(0.33 - 0.47 in)
3. Install the under plate.
YS828TM
11-16mm
(0.43 - 0.63 in)
Track Adjustment
1. Loosen the adjuster locknuts.
2. Turn the adjusters in or out un-
til proper track deflection is
achieved.
CD Locknut
~ Adjuster
3. Tighten the locknuts.
-39- -40-
('
- WARNING:
-41- -42-
704-001
G-701 B-716
B-710
ENGINE
1. Remove the spark plug, pour
about one tablespoon of SAE
10W30 or 20W40 motor oil into
the spark plug hole and reinstall
the spark plug. Recoil start the
engine by turning over several
times (with ignition off) to coat
the cylinder walls with oil.
-43- -44-
('
Overall Height mm (in) 1,135 (44.7) 1,140 (44.9) 1,135 (44.7) 1,140 (44.9)
Dry Weight kg lib) 92 (203) +- 103 (227) +-
ENGINE
Model Code Number Unit YS624TMI YS624WM I YS828TM I YS828WM
Type *1 Forced air cooled 4-stroke gasoline SV L-c::J
Cylinder Arrangement *2 Inclined, 1-Cylinder
Displacement cmJ 202 291
.y--c::J
Bore x Stroke mm (in) 69x54 (2.7x2.1) 78x61 (3.1 x 2.4)
Maximum Output psi rpm 6/4,000 8/4,000 -
Fuel
B
Regular gasoline
Fuel Tank Capacity Total L (Imp gal, US gal) 5 (1.1, 1.32)
Engine Oil Quantity L (Imp qt, US qt) 0.68 (0.60, 0.72) 0.95 (0.84, 1.04)
Ignition System T.C.I.
Spark Plug: Type BPR4HS (NGK)
0.6-0.7 mm (0.024-0.028 in)
t
.:..
Gap .........
.............
! CHASSIS ~~~~~~~~
.:.:.:.:
Model Code Number Unit T
YS624TM YS624WM YS828TM I YS828WM
:1
Snow Removal:System 2 stage, auger blower
Capacity Ton/h Ub/li) 35 (1,290) 50 (1,840)
deg
550 (22)
14 (46)
220
620 (24.5)
15 (50)
Y Yellow 011/4
II
CD Main switch G-825
B Black (j IIID
Auger Up-down System
1
Manual
I
~ TCI unit G-835
Driving System Track Wheel Track I Wheel
<ID Spark plug G-831 L Blue C,II/II
Transmission System Friction Disc B/W Black/White 1111/1
@ Lighting coil 8-802
Vehicle Speed: 1st km/h (m.p.h.) 0.97 (0.61) +- +- +-
Forward 2nd km/h (m.p.h.) 1.89 (1.18) +- +- +-
3rd km/h (m.p.h.) 2.76 (1.73) +- +- +-
1
4th km/h (m.p.h.) 3.60 (2.25) +- +- +-
r
Neutral +- +- +-
Reverse 1st km/h (m.p.h.) 1.74 (1.09) +- +- +-
2nd +- +- +- ,
km/h (m.p.h.) 2.68 (1.68)
-45-
-46-
","