Professional Documents
Culture Documents
Keyless Entry System: 2. Transmitter
Keyless Entry System: 2. Transmitter
Keyless Entry System: 2. Transmitter
B6M0950
Perform lock and unlock with door lock switch.
: Does the power door lock function 2) Measure voltage battery.
normally? NOTE:
: Go to step 4B21. I Battery discharge occurs during measurement.
: Repair power door lock. Complete measurement within 5 seconds.
I During battery voltage measurement, voltage
falls more than 1.8 volts during 3 seconds period.
Weak battery is indicated. Replace battery.
S6M0291A
53
6-2 [T4B2] DIAGNOSTICS
4. Keyless Entry System
54
DIAGNOSTICS [T4B3] 6-2
4. Keyless Entry System
55
6-2 [T4B4] DIAGNOSTICS
4. Keyless Entry System
Measure voltage between fuse box connector Measure resistance between keyless entry control
(B158) and chassis ground. module connector (B176) and chassis ground.
Connector & terminal Connector & terminal
(B158) No. 8 (+) — Chassis ground (−): (B176) No. 8 (+) — Chassis ground (−):
B6M1344B B6M0953A
B6M0952A
56
DIAGNOSTICS [T4C0] 6-2
4. Keyless Entry System
S6M0450A
(1) Horn (3) Horn relay (in main fuse box) (5) Door switch
(2) Keyless entry control module (4) Rear gate latch switch
57
6-2 [T4D0] DIAGNOSTICS
4. Keyless Entry System
D: SCHEMATIC
S6M0451
58
DIAGNOSTICS [T4D0] 6-2
4. Keyless Entry System
S6M0452
59
6-2 [T4E0] DIAGNOSTICS
4. Keyless Entry System
B6M0957
4F11 : CHECK KEYLESS ENTRY FUNC- Check if the horn signal chirps.
TION.
: Does the horn chirp one time?
: Go to step 4F13.
1) Perform pre-inspection.
<Ref. to 6-2 [T4B0].> : Go to step 4F21.
2) Remove ignition key from ignition switch.
3) Set the room light switch in the middle position.
4) Close all doors and the rear gate.
5) Press the LOCK/ARM button one time.
: Do all doors and rear gate lock nor-
mally?
: Go to step 4F12.
: Replace keyless entry control module.
<Ref. to 6-2 [W10A1].>
60
DIAGNOSTICS [T4F1] 6-2
4. Keyless Entry System
4F13 : CHECK KEYLESS ENTRY FUNC- 4F18 : CHECK KEYLESS ENTRY FUNC-
TION. TION.
Press the UNLOCK/DISARM button one time. 1) Keep the LOCK/ARM button pressed for more
: Does the driver’s door unlock nor- than 1.5 seconds.
mally? 2) Horn will sound, and then press the LOCK/ARM
button.
: Go to step 4F14.
: Does the horn turn off?
: Replace keyless entry control module.
<Ref. to 6-2 [W10A1].> : Go to step 4F19.
: Replace keyless entry control module.
4F14 : CHECK KEYLESS ENTRY FUNC- <Ref. to 6-2 [W10A1].>
TION.
4F19 : CHECK KEYLESS ENTRY FUNC-
Check if the horn signal chirps. TION.
: Does the horn chirp two times?
1) Keep the LOCK/ARM button pressed for more
: Go to step 4F15. than 1.5 seconds.
: Replace keyless entry control module. 2) Horn will sound, and then press the UNLOCK/
<Ref. to 6-2 [W10A1].> DISARM button.
: Does the horn turn off?
4F15 : CHECK KEYLESS ENTRY FUNC-
TION. : Go to step 4F110.
: Replace keyless entry control module.
<Ref. to 6-2 [W10A1].>
Check if the room light is turned on.
: Does the room light turn on for 30
seconds, and then turn off? 4F110 : CHECK DOOR SWITCH FUNCTION.
: Go to step 4F16.
Open the front left door.
: Go to step 4F31.
: Does the room light turn on?
4F16 : CHECK KEYLESS ENTRY FUNC- : Go to step 4F111.
TION. : Go to step 4F41.
1) Press the LOCK/ARM button one time. 4F111 : CHECK DOOR SWITCH FUNCTION.
2) Press the UNLOCK/DISARM button two times.
: Do all doors and rear gate unlock 1) Close the front left door.
normally? 2) Open the front right door.
: Go to step 4F17. : Does the room light turn on?
: Replace keyless entry control module.
: Go to step 4F112.
<Ref. to 6-2 [W10A1].>
: Go to step 4F41.
4F17 : CHECK KEYLESS ENTRY FUNC-
TION. 4F112 : CHECK DOOR SWITCH FUNCTION.
Keep the LOCK/ARM button pressed for more than 1) Close the front right door.
1.5 seconds. 2) Open the rear left door.
: Does the horn sound for 30 seconds, : Does the room light turn on?
and then turns off? : Go to step 4F113.
: Go to step 4F18. : Go to step 4F41.
: Replace keyless entry control module.
<Ref. to 6-2 [W10A1].>
61
6-2 [T4F1] DIAGNOSTICS
4. Keyless Entry System
4F113 : CHECK DOOR SWITCH FUNCTION. 4F115 : CHECK IGNITION KEY SWITCH.
1) Close the rear left door. 1) Insert the ignition key to the ignition switch (at
2) Open the rear right door. LOCK position).
2) Perform lock and unlock with transmitter.
: Does the room light turn on?
: Go to step 4F114. : Does the power door lock function
normally?
: Go to step 4F41.
: Go to step 4F61.
: End of basic diagnostics procedure.
4F114 : PERFORM PROGRAMMING.
NOTE:
Finish operation from step 1) through 4) within 45
seconds.
1) Sit on the driver’s seat and close all doors and
the rear gate.
2) Open the driver’s door.
3) Close the driver’s door.
4) Turn the ignition switch from ON to LOCK ten
times in rapid succession (within 15 seconds).
NOTE:
Do not start the engine at this time.
5) The horn chirps one time to indicate that the
system has been in the programming mode.
6) Open the driver’s door.
7) Close the driver’s door.
8) Press any button on the transmitter that you
wish to program into the system.
9) Horn will chirp two times to indicate that the
transmitter has been programmed.
NOTE:
Any additional transmitter can also be pro-
grammed at this time. Repeat steps 6) through 9)
for an additional transmitter.
10) Remove the ignition key from the ignition
switch.
11) The horn will chirp three times to indicate that
the system has exited the programming mode.
12) Check the keyless entry system properly oper-
ates by operating each transmitter.
: Does the transmitter operate nor-
mally?
: Go to step 4F115.
: Go to step 4F51.
62
DIAGNOSTICS [T4F2] 6-2
4. Keyless Entry System
B6M0958A
B6M1349B
63
6-2 [T4F2] DIAGNOSTICS
4. Keyless Entry System
B6M1350B
B6M1351A
: Does continuity exist?
: Repair wiring harness of horn circuit. : Is the voltage more than 10 V?
: Replace horn relay. : Go to step 4F28.
: Repair wiring harness between main
4F26 : CHECK FUSE. fuse box and battery.
64
DIAGNOSTICS [T4F3] 6-2
4. Keyless Entry System
1) Disconnect connector from main fuse box and Remove and visually check the fuse No. 2 (in main
keyless entry control module. fuse box).
2) Measure resistance between keyless entry con- : Is fuse No. 2 blown?
trol module connector (B176) and main fuse box
: Replace fuse (15 A).
connector (F37).
: Go to step 4F32.
Connector & terminal
(B176) No. 12 — (F37) No. 4:
4F32 : CHECK ROOM LIGHT BULB.
B6M0960A
65
6-2 [T4F3] DIAGNOSTICS
4. Keyless Entry System
B6M0961A
B6M0962A
: Is the voltage more than 10 V?
: Go to step 4F35. : Is the resistance less than 10 Ω?
: Repair wiring harness between room : Replace keyless entry control module.
light and battery. <Ref. to 6-2 [W10A1].>
: Repair wiring harness between room
light and keyless entry control module.
66
DIAGNOSTICS [T4F5] 6-2
4. Keyless Entry System
B6M0070A
S6M0453A
67
6-2 [T4F6] DIAGNOSTICS
4. Keyless Entry System
Remove and visually check the fuse No. 6 (in main 1) Disconnect connector from key warning switch.
fuse box). 2) Measure voltage between key warning switch
: Is fuse No. 6 blown? connector (B74) and chassis ground.
: Replace fuse (15 A). Connector & terminal
: Go to step 4F62. (B74) No. 2 (+) — Chassis ground (−):
B6M0965A
68