Professional Documents
Culture Documents
Spe 2166 Pa
Spe 2166 Pa
Production
The drilliig of deep, abnormally pressured wells h Three modifications of the basic depth-of-sealing
the Gulf Coast area has brougbt about the need for approach to pore pressure calculation using shale cut-
accurate definition of the physical forces necessary to ting density’-’ have been compared with two pub-
contain such anomalous pressure so that protectiv~- lished empirical correlations. A GE Model 265 com-
casing can be set and drilling can be continued with- puter and Gl?s time-sharing service were used in this
out costly interruptions. It is not enough merely to study.
recognize the presence of abnormal pressures. The
magnitude of these pressures must be defined so that Basic Theory
(1) drilling fluids can be selected to optimize penetra- The most generally accepted theory explaining over-
tion rate, (2) hydrocarbon shows from productive for- pressured reservoirs is based upon the Terzaghi and
mations can be recognized, (3) damaging fluid entry Peck’ perforated plate and spring model, Fig. 1A.
into potential pay sands can be lessened, and (4) elec- From this analogy representing the shale compaction
tric Jog data can be interpreteted more reliably. process, Hubbert and Rubeyl concluded that abnor-
Location of the transition zone between normal and mal pressures occurred when water was not permitted
abnormal pressures is of prime importance. Many to escape from a closed system (Stage A, Fig. 1A)
excellent techniques have been developed to aid in its faster than overburden pressure was applied. Nor-
location and also to evaluate pressure requirements mally, wmpaction progresses to Stage C, or compac-
for drilling below these zones. Most of these tools, tion equilibrium as defined by Hubbert and Rubey,
such as electric, sonic and density logs are used “after where the fluids are under normal hydrostatic pres-
the fact” and are diagnostic only if run at the proper sure and the overburden is supported entirely by the
depth. Therefore, some method is necessary to pro- springs or the grain-to-grain bearing stress of the rock.
vide information concerning impendhg high pressure When normal leakoff cannot occur, as in Stage A,
zones as soon as they are penetrated by the bh. Two the overburden load is supported entirely by the en-
methods are in popular use today: (1j normalized trapped water, and the fluid pressure reaches its ulti-
drilling rate or “D” exponent determination,’ which mate value of 1.0 psi per foot of depth.
is premised upon a relationship between rate of pene- Isolated sand bodies in massive shale sections are
tration and differential pressure, ‘and (2) determina- often the recipients of water from compacting shales
tion of the variation in the density of shale cuttings. — a situation normally found in the Gulf Coast re-
Four methods of calculating formation pore pressures ~,td resultant fracture gradients
have been adapted to the computer and are compared with an empirical correlation and
electric log computations and with observed conditions such as mud weights used, gas
kicks and other indications of pressure.
gion and represented by Stage B, Fig. 1A. Some on many Gulf Coast wells, a consistent normal pres-
compaction has necessarily occurred since the sand sure gradient of 0.465 psi/ft. This gradient is equiva-
body has become “charged” and the fluid pressure lent to a column of fluid weighing 9.0 lb/gal or water
gradient has reached a value greater than 0.465 psi with a sodium chloride content of 80,000 ppm.
and less than 1.0 psi per foot of depth. Armed with this information and the basic depth-
Fig. lB illustrates key shale characteristics that of-sealing concept, one can easily determine pore
provide the basic theory for pressure calculations. pressure. Using typical shale cutting density vs depth
Shale porosity is plotted vs depth, with pressure gradi- data shown on Fig. 2 as an illustration, note that a
ent as the third variable. The data presented by Dick- sharp departure from the normal trend of increasing
inson,6 which was derived from in-situ density meas- density with depth occurs at Point “T”. Since abnor-
urements and estimates used by geophysicists for mally high porosities will prevail in overpressured
Tertiary sediments of the Gulf Coast, provide the shales, the bulk density will be correspondingly re-
basis for this calculation made by Wickenhauser.7 duced due to the presence of higher than normal
Note that under normal pressure (p, = 0.465), amounts of water for that depth. Assuming a linear
s
s
s
v. 1 1 1
— DEPTH OF SEALING
(Ds )
Prsl i >~r>O.465 Pr =0,465
35 I
%=1.00
1- ?
Z
30 - i
u
u
~ !
>“ 25 -“ I — “T” TR_,.31TiON ZONE–
~
m
o ~ (DP)
—+—- +NORMAL
I II
TREND DATA FIT
!5 20 -
a DS=I.tMIXp P+A
w }
z’ ,5 -
z p, S FLUi D PRESSURE
OVERBURDEN PRESSURE
DEPTH, FT X iOs
Fig. lB—Porosity vs depth for average Gulf Coast shales. Fig. 2—Typical density-shale cuttings vs depth.
1464
.
Where D,, is the depth at which the abnormally low (Controlled experiments with finer cuttings produce
density p,,was encountered. much more consistent density measurements.l”) The
In this analysis complete sealing of the shale bed cuttings are then examined microscopically to select
has been assumed; however, as Dickinsons and others clean, uniform shale pieces for density determination
have discovered, this. is not the usual occurrence. and to obtain a routine mud logger’s lithology de-
Often, because of relatively fast subsidence in sedi- scription, To prepare them for measurement, these
mentary basins and because of the inability of shales samples are dried only mough to remove adsorbed
to give up water readily, only partial sealing takes surface water.
place. In such cases, the apparent depth of sealing is The calibrated fluid column utilizes two completely
estimated in the same manner, and the pressure is cal- miscible liquids that establish a linear density gradi-
culated from Eqs. 1 and 2. ent. me column is calibrated by dropping several
glass beads of known density into the fluid and plot-
Measurement of Shale Density from ting density vs the height at which these beads come
Drilled Cuttings to rest. The resultant straight-line relationship is used
METHOD i METHOD i?
DENSITY _
)
COMPOSITE OENSITY CURVE DEPTH OF SEALING
t t
c $ ApmdO = APL t t
1 I IIp).
(Pn,Op)
\ \
METHOD 3 METHOD 4
L
DEPTH OF SEALING
*
1* O$=A+mp
D~=A+mPc
4“
t “e
Pc-pP=Ap
I Wm E A [Af)m)
IDP)
Ap
i
PORE PRESSURE = 0.465 (DJ + 1.0 (C)p - DJ { UNITED CORE CORRELATION )
g
E
LEAST SOUARE CURVE FIT
FOR NDRMAL TREND DATA
t
* 6
I
23
s
+
z
SELECT ABNORMAL OENSITY n
POINTS AND CALCULATE OEPTH
OF SEALING BY EOUATIDN: 2
O$=A+mp s
$x
g
CURVE FIT MUO WEIGHT VS.
a
z!i * .[
OEPARTURE CORRELATION
Wm = A IAPm)
1-
CALCULATE CALCULATE DEVIATION
ANO THEN Wm FROM
FROM D~
wm. A (Apm) kND CONVERT
OVERBURO
TO PORE
+ +
CURVE FIT MATRIX STRESS COEFFICIENT VERSUS DEPTH CURVE Y = AKm
AND PROCEED WITH MATTHEWS & KELLEY TECHNIQUE
TO CALCULATE FRACTURE GRADIENT
lag time of the annular mud stream, considering hy- J2ETHOD HO. ~
MuD WT. PORE PRESS
draulics and hole geometry, is calculated. OENSITY FRAC. PRESS. FR4C, MuD
14500 220 1103 a315 13225 17.64
14800 2.22 1090 8392 13351 17.6 I
Method of Analysis 15300
15400
Z.80
2 15
1309
1240
10412 13946
1406S
17.53
17.56
9929
Figs. 4 and 5 schematically represent the four meth- 15500 2 14 1260 10I54 14 I 59 1757
7). The calculation utilizes the depth-of-sealing analy- Fig. 6-Typical program printout.
sis with integration of the composite curve between
OENSITY - WALE CU?71NCW — 6H/C6’
D, and DP as the overburden pressure.
2.1 2.2 2.3 2.4 2.5
Dickinsona suggested that overburden pressures on 1 1
the Gulf Coast could be calculated on the basis of the 2
shale-density:depth relationship, Fig. 8 compares 3 . “\
overburden pressure determined from shale density 4 . \,\
data with an assumed gradient of 1.0 psi/ft. In the ‘.
5 . ‘.
depth range of most deep wells today (about 20,000 .,.
ft), use of 1,0 psi,/ft in estimating overburden pres- “.
k: - \
sures will result in a value that is slightly low. The
t!
“X” points on Fig. 7 represent curve fit data for the
composite density data, which take the form of $?8
Wg
-
\ ~.
D, = (p./Om . . . . . . . . (3) f
10
~
L
,11
Integration of this equation between D, and DP,
yields the average density, which is then converted to ~ 12 .
‘,
pressure gradient, The normal pressure component $ 13 .
is calculated in the conventional manner. 14 . \
Methods 2 and 3 are based upon the depth-of-seal- 15 .
ing theory2-4and differ only in the calculation of over-
[6 . \
burden pressure. Method 2 obtains overburden pres- ,7 X-CURVE FIT DATA
sure from an integration of the composite density \
O-ACTUAL DENSITY
curve as in Method 1, whereas Method 3 assumes an 18 . MEASUREMENTS }0
4
overburden gradient of 1.0 psi/ft. From an examina- 191
tion of the results of calculations on several wells, it
I was concluded that the assumed overburden gradient
Fig. 7-Composite density vs depth, Gulf Coast, La.
(courtesy Baroid).
I of 1.0 psi/ft provides sufficient accuracy for most pore 30, A
pressure determinations.
Both methods utilize the first order, least-squares
equation to provide a relationship between depth and
density
D, = ?nxpp+A . . . . . . . (1)
Knowing abnormal density data, we can determine
the depth of sealing and can complete the calculation
as outlined.
Method 4 uses the relationship’” between deviation
of density from the normal trend and mud weight re-
.. quired (Fig, 9), Deviation vs mud weight data, plotted
on log-log paper, result in the equation
-o 10,000 eo,ooo 30,000
w. = A(A/2)~, . . . . . ...(4) PRKSSURE OF OVERBURDEN - PSIO
Rearranging Eq. 1 to solve for p~, Fig. 8-Overburden pressure vs depth (after Dickinson).
“
NOVEMBER, 1969 1467
Ds– A approximately 12,000 ft. Method 1 calculations agree
PP= ~ “ “ “ “ “ “ “ “ “ @ very well with actual mud weights except in the re-
gression zones at 15,600 ft and at 17,200 ft, where
By replacing D, with Q, the density that would be the mud weights were affected by the proximity of
found in nom~ally pressured rocks (PC) at Dp can be sand bodies in these areas. Loss of water from shales
calculated: surrounding these sands results in abnormally high
shale density values that yield inaccurately low pore
PC = DP– A . . . . (6) pressures and mud weight requirements when used in
m“”””
the calculations.
This calculated density (PC’)is subtracted from pp at The 7-in. casing is set well into the abnormal pres-
the depth of interest to obtain deviation (Ap), which sure zone and is in good position for drilling deeper
is used in Eq. 4 to obtain mud weight. without exceeding fracture pressure of shallower,
The correlation presented by Rogers’ (Fig, 9) was normally pressured formations. Had casing not been
also used as a comparison; however, we were unable set at 13,200 ft, the fracture pressure of the zones
DENSITY —
.6r
.5 —
x
1-
&
w v ,4 —
0 v
2
I
w
; .3 —
o
i=
a
s .2 —
w
n
J—
II MUD WT
ME1’H i IES ROGERS BOATMAN USED
— — — —— — i ——— “
) PORE PRESSURE
L 7“ CASING
(METHOD 1)
. . . . . . . ..-
FRAC GRADIENT
( METHOD i )
<’ $
>
/ 4 #
/ f
/’
\ \/
\
L 5“ LIN ER -LOST 50 ~~LS MUD
\
PER HR WHILE DRLG
t
/ -“ / ‘
,’
4 f 1
18 .- LOST 50 BBLS MUD
PER HR
19
2.0 2.1 2.2 2.3 2.4 2.5 OENSITY - WALE CUTTINGS -- 6W/Cc
=&
8
1 0 NORMAL TREND DATA
9— —
● ABNORMAL PRESSURE POINTS
10
4
1
II +;~a MUD WT
METH I I ES ROGERS BOATMAN USED
16 Y
-/”
14.5
12.4
16.7
15.8
17.6
17.4
21.”1
20.8
17. !3
1?.5
17
sure values that are unreliable, The correlation pre- on Fig. 15 represents the least-squares fit for all data
sented by Rogers and Method 1 best approximate and was used as reference for both Baroid and United
the diaymal “line of agreement” on Fig. 12. Boat- Core methods. The transition to abnormal pressures
man’s correlation (Method 4) was also influenced by is apparent at 11,500 ft; protective casing is set at
the normal trend tune and generally yielded values 11,200 ft. Had this transition gone undetected, this
that were too high, zone would have been penetrated with 12-lb/gal mud,
Fig. 13 shows density m depth data on an offshore which would not have contained pore pressures equiv-
Louisiana well. It indicates an ummml.ly flat normal alent to 15 lb/gal. The 9%-in. casing could have been
trend and accounts for the low mud weights calcu- set some 600 ft lower and provided protection for the
lated from depth-of-sealing analyses (Methods 2 and normally pressured shale from 11,200 ft to the transi-
3) and high values based upon deviation from the tion at 11,500 ft. Fortunately, the fracturing pressures
trend (Boatman and Rogers). This well illustrates one of this interval were not exceeded when the well was
very critical situation that ctm occuc at extremely drilled deeper.
high pressures, the fracture gradient and pore pressure Pore pressure calculations based upon the com-
converge and drilling can be continued only on a very posite density curve (Method 1) have led to the con-
I
I t I I ( I
tTTTT_TT
16
.1?
NOVEMBER,1%9 1471
E
10
msi=-DENs’T’”-s
-i
—--
——.
—
—
MUD WT
METH I I ES ROGERS 130ATMAN USED
—-— .—-—
\
*.-f‘
_..
.,-””1:
\
_— - . -------”- ‘ 12.5 12.8 13.9 156
\ / ““ 9
f
13.2 14.5 12.6 13.7 15.6
4-.—
: J .— -—— —- 14.4 15.2 14.4 15.5 168
—-—. .-/_
-.— i.___
t-- 14.9 l?. I 15 2 16 5 168
—.
—. —
I I
ACTUAL MUD WEIGHT
———
\ PORE PRESSURE
(METHOD 1)
+ --------
FRAC GRADIENT
(METHOD t)
\
I
i
\
\
3 1\
\
\
k- \
1’\\
14
11
‘- NORMAL TREND DATA
. . ABNoRMAL pREssu RE polNTs
12 ‘
k
g 9y’cs 2L
13
s
8
~ 14
~
\ MUD WT
~ 15 hlETH.1 RoGERS BOATMAN USED
Q
~, 16,9 15.9 17.6 17.5
\ 16.7 15.8 17.5 17.5
‘6 7“ LIN f:R L 4 18. I 16.9 19.4 i%.o
> 17.7 17.0 18.9 18.1
I ‘t \ 17.8 17.2 19. I 18.3
18
Fig. 17—Density-shale cuttings vs depth.