Professional Documents
Culture Documents
2301D-J Digital Governor
2301D-J Digital Governor
03239C
• Digital speed
control
• Alternate
dynamics
• Compatible with
existing load
sharing system
• Remote speed &
2301D-J Digital Governor load reference
for Medium & High Speed Engines and Generators • Analog and
discrete outputs
with Automatic Load Sharing
• Soft load transfer
• PC configurable
with Woodward
Description I/O Watch Window
Software
The Woodward 2301D-J is a The 2301D-J has following inputs and • For engines of
microprocessor-based generator and engine outputs. the rated speed,
control with automatic load sharing and 400-3600 rpm
speed control. • KW input (1):
3 phase PT input: 90-240 Vac/45-65 Hz • Actuator output
The control is housed in a sheet-metal 3 phase CT input: 2-6 A at the rated current
chassis and consists of a single printed generator load 0-180 mA,
circuit board. 0-20 mA,
• MPU input (1): 4-20 mA or
The 2301D-J adds a soft-loading/unloading Input range: 100-20 000 Hz, 1-30 Vac 180-0 mA(reverse
feature to the control system equivalent to Rated speed control range: acting) software
the old 2301A LSSC plus Woodward Digital for medium&high speed 600-3600 rpm configurable
Reference Unit. This control switches its
operation mode bumplessly between • Analog inputs (2):
isochronous mode and droop mode. Input signal: software configurable to one
of ±2.5V, 4-20 mA, 0-5 V or 1-5 V with
The 2301D-J is configured using a computer each input channel.
with Woodward Watch Window software. The Input 1: Synchronizer input.
configuration software is supplied with each Input 2: configurable to one of following
control, and users may download from the inputs:
Woodward web site as well. The computer Remote speed reference input
connects to the 2301D through a 9-pin Remote baseload reference input
connector (RS-232 port). Remote speed bias input
Manifold air pressure input
Power supply voltage for the 2301D-J is 18-
40 Vdc (nominal 24 Vdc).
Control Functions the generator circuit breaker was
closed while in KW droop operation)
• Discrete inputs (8): 8 input channels
are used to detect 10 command/ 2301D-J features speed control, load
status inputs below. control, operation mode transfer • Soft-unloading (with the generator
RUN/STOP command between the isochronous mode and the circuit breaker open signal when the
Idle/Rated speed droop mode while operating a generator load reached the unload
MPU failure override generator with load, and various fuel trip level.)
Speed/Load raise limit functions.
Speed/Load lower • Isochronous and Baseload control
Auto unloading command Speed Control:
Isochronous/Droop • KW droop control
• Engine’s rated speed range:
Generator Circuit Breaker Aux
400-3600 rpm
contact input Isochronous/Droop transfer:
Remote speed (load) reference
select • Transfer between ‘Isochronous’ and Transferable from isochronous load
Baseload operation ‘KW droop’ sharing operation to KW droop
operation bumplessly without any
• Actuator output (1): the current range • Simple speed droop control (No frequency or load fluctuation. When
is 0-180 mA, 0-20 mA, 4-20 mA or generator KW droop function) transferring from KW droop operation
180-0 mA (for reverse acting). to generator load sharing operation, the
• Idle/Rated speed selection generator load is ramped smoothly
• 4-20 mA analog output (1): configur- from the KW droop level to the
ed to Engine speed, Speed reference, • Raise/Lower speed with contact isochronous load sharing level by the
Actuator output, Generator KW inputs soft-loading function.
output or Generator KW reference.
• Remote speed reference with an Isochronous baseload operation:
• Discrete outputs (4): Low-side drivers external analog input signal
The baseload reference is
with maximum sink current of 200 mA. raised/lowered with Raise/Lower
A 12 Vdc or 24 Vdc external power • Either a single gain or a 4 slope gain
contact inputs or an analog remote
must be connected to each load. curve (gain is determined
signal to the desired load level.
corresponding to the load) is
Two are for fixed use (not available
The generator load is maintained to the
configurable): constant level specified in spite of any
Speed switch • Alternate dynamics (switched when Mains frequency variation while in the
Generator Circuit Breaker open the engine load reached the preset baseload operation.
level)
Two are configurable outputs: Each
output is configurable to one of Fuel Limit: Woodward Part Numbers
following status signals
• Start fuel limit (Lower limit, Upper
CPU failure
limit, Ramp rate from Lower limit to
MPU failure 2301D-J’s part number is as follows:
Upper limit)
C.B. closed in isochronous
operation
• Maximum fuel limit • For medium and high speed (400-
C.B. closed in droop operation 3600 rpm) engine control:
In baseload operation P/N 8273-126 revision D or upper
KW switch • Manifold air pressure fuel limiter is
configurable
NOTE: Former 8273-125 and 8273-
126 were integrated to 8273-126
• Torque fuel limiter is configurable
when its revision was changed to
‘D’.
Generator load control:
• Isochronous load sharing (with soft- Woodward Watch Window software
loading function to load the generator must be used to operate and tune a
from the Circuit Breaker close to the 2301D-J control. (The Watch Window
Load sharing start) software is attached to each 2301D-J.)
Power Supply:
Power Supply Rating ........... 18-40 Vdc (Nominal 24-32 Vdc)
Power Consumption ............ less than or equal to 20 W normal................. Power Supply Voltage .... Input Current
18 V................................. 589 mA
24 V................................. 431 mA
32 V................................. 320 mA
Inrush Current ...................... 7 A for 0.1 msec
Speed Control:
Steady State Speed Band ... ±0.25 % of rated speed
Environmental Specification:
Operating temperature......... –40 °C to +70 °C (–40 °F to +158 °F)
Storage temperature ............ –40 °C to +105 °C (–40 °F to +221 °F)
Humidity ............................... +95 % at +20 °C to +55 °C (+68 °F to +131 °F)
Lloyd’s Register of Shipping Specification Humidity Test 1
Mechanical Vibration ........... Lloyd’s Register of Shipping Specification Vibration Test 2
Mechanical Shock................ US MIL-STD 810C, Method 516.2, Procedure I (basic design test), Procedure II (transit
drop test, packaged), Procedure V (bench handling)
Regulatory Compliance:
European Compliance for CE Mark:
EMC Directive ................. Certified to 89/336/EEC COUNCIL DIRECTIVE of 03 May 1989 on the approximation of
the laws of the member states relating to electromagnetic compatibility.
Low Voltage Directive ..... Certified to the 73/23/EEC COUNCIL DIRECTIVE of 19 February 1973 on the
harmonization of the laws of the Member States relating to electrical equipment designed
for use within certain voltage limits.
Corporate Headquarters
Rockford IL, USA
Ph: (1)(815) 877-7441
www.woodward.com
This document is
distributed for informational
purposes only. It is not to
be construed as creating or
becoming part of any
Woodward Governor
Company contractual or
warranty obligation unless
expressly stated in a written For more information
sales contract.