Professional Documents
Culture Documents
Fuel Control - Test
Fuel Control - Test
Fuel Control - Test
Pantalla anterior
Bienvenido: r050jm1
i03202426
Use this procedure to determine if the Electronic Control Module (ECM) is properly controlling the fuel
rack.
The engine is electronically controlled by the ECM. The ECM senses the engine rpm by using the engine
speed sensor. The ECM controls the fuel rack by adjusting the voltage to the Rack Solenoid. Refer to
Troubleshooting, "System Overview" for more information.
The following variables are used in this test. These variables will be displayed on the electronic service tool.
• Desired engine rpm is an input to the electronic governor within the ECM. Desired engine speed is
based on throttle inputs, the engine speed sensor's signal and customer specified parameters.
• The desired rack position indicates the position of the rack in order to maintain the desired engine
rpm. The desired rack position will not exceed the rack control for the fuel ratio. Also, the desired rack
position will not exceed the rated rack limits.
• The ECM receives a signal from the rack position sensor. The ECM uses this signal to calculate the
actual rack position. The ECM uses the rack position sensor signal as feedback to allow precise
control of the rack position. The actual rack position follows the desired rack position if the rack
controls are functioning properly.
• The rack control for the fuel ratio limits the fuel to the air ratio. The limit is used to reduce black
smoke during acceleration. When the ECM senses a higher inlet manifold pressure, the rack control
for the fuel ratio is increased in order to allow more fuel.
• The rated rack is a limit on the rack position that provides the specified power and torque curves. The
rated rack is programmed into the personality module.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 07/08/2017
3412 Generator Set 4BZ00001-UP(SEBP2785 - 48) - Documentación Página 2 de 4
Illustration 1 g01634937
Illustration 2 g01635554
(10) + 8 VDC
(30) + 5 VDC
Test Step 1. Inspect the Electrical Connectors and the Wiring Harness
B. Thoroughly inspect the J6/P6 connector for the rack solenoid (BTM) and the J11/P11 connector for
the rack position sensor. Inspect the ECM connector J14/P14. Refer to Troubleshooting, "Electrical
Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 07/08/2017
3412 Generator Set 4BZ00001-UP(SEBP2785 - 48) - Documentación Página 3 de 4
D. Check the allen head screw on the ECM connector for the proper torque. Refer to Troubleshooting,
"Electrical Connectors - Inspect" for the correct torque values.
Expected Result:
All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free
of corrosion, of abrasion and of pinch points.
Results:
• OK - All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and
wiring are free of corrosion, of abrasion and of pinch points. Proceed to Test Step 2.
Repair: Repair the wiring and connectors or replace the wiring or the connectors. Ensure that all of
the seals are properly connected. Verify that the repair eliminates the problem.Verify that the repair
eliminates the problem.
STOP
C. Monitor the desired engine rpm, the desired rack position and the actual rack position on Cat ET.
Note: A lag in Cat ET may cause differences in the displayed values for the desired rack position and
the actual rack position. For a typical engine at low idle with normal accessory loads, the desired rack
position and the actual rack position is approximately 4.50 mm (0.18 inch) to 5.25 mm (0.20 inch).
Expected Result:
The desired engine rpm should equal the programmed low idle setting and the rpm should remain steady.
The actual rack position should follow the desired rack position within ± 0.5 mm (± 0.02 inch).
Results:
• OK - The desired engine rpm is equal to the programmed low idle setting and the rpm remains steady.
The actual rack position follows the desired rack position within ± 0.5 mm (± 0.02 inch). Proceed to
Test Step 3.
STOP
STOP
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 07/08/2017
3412 Generator Set 4BZ00001-UP(SEBP2785 - 48) - Documentación Página 4 de 4
D. Monitor the desired rack, the rated rack and the rack control for the fuel ratio on Cat ET.
Expected Result:
The desired rack reaches the rated rack when the engine is fully loaded.
Results:
• OK - The desired rack reaches the rated rack when the engine is fully loaded.
Repair: The rack operation is working properly. Refer to Troubleshooting, "Electrical Connectors -
Inspect" for a intermittent problem.
STOP
• NOT OK - The desired rack is limited to the rack control for the fuel ratio which indicates low boost
pressure.
Repair: Refer to Troubleshooting, "Inlet Manifold Pressure - Test" for further information.
STOP
• NOT OK - The desired rack is limited to a value below the rated rack.
Repair: The ECM may be limiting engine power or rpm. Refer to Troubleshooting, "Engine Top
Speed Is Not Obtained" for further information.
STOP
Copyright 1993 - 2017 Caterpillar Inc. Mon Aug 7 13:32:18 UTC-0300 2017
Todos los derechos reservados. r050jm1
Red privada para licenciados del SIS.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 07/08/2017