Professional Documents
Culture Documents
GTSIO 520 H Operators
GTSIO 520 H Operators
GTSIO 520 H Operators
OPERATOR’S
MANUAL
FAA APPROVED
Publication X30129
©
CONTINENTAL MOTORS, INC. AUGUST 2011
Supersedure Notice
This manual revision replaces the front cover and list of effective pages for Publication Part
No. X30129, dated May 1979. Previous editions are obsolete upon release of this manual.
Available exclusively from the publisher: P.O. Box 90, Mobile, AL 36601.
Copyright © 2011 Continental Motors, Inc. All rights reserved. This material may not be reprinted,
republished, broadcast, or otherwise altered without the publisher's written permission. This man-
ual is provided without express, statutory, or implied warranties. The publisher will not be held liable
for any damages caused by or alleged to be caused by use, misuse, abuse, or misinterpretation of
the contents. Content is subject to change without notice. Other products and companies men-
tioned herein may be trademarks of the respective owners.
i
T ABLE OF CONTENTS
Introduction ..................................................... 1
Section X Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 73
INTRODUCTION
1
WARNING ... This engine must be installed in accordance with
all requirements and limitations listed in the Detail Specification
for Teledyne Continental Aircraft Engines. Any deviations caused
by installation, or operation, such as acrobatic maneuvers will be
deemed as misuse and Teledyne Continental Motors shall be
relieved of any further responsibility.
2
SECTION I
When increasing power, first increase the RPM with the propeller
governor and then increase manifold pressure with throttle. When
decreasing power, throttle back to desired manifold pressure and
then change propeller governor to desired RPM.
3
DETAIL SPECIFICATIONS
RATINGS:
CYLINDER DATA
FUEL SYSTEM
LUBRICATION SYSTEM
4
------~.~--~-~~-~- .... -~
ACCESSORIES
5
0\ OPERATING SPECIFICATIONS
MAXIMUM RECM. PERFM RECM. ECONOMY
OPERATION H.P. (1) CLIMB CRUISE CRUISE CRUISE IDLE RUN UP·
%NRP 100 75 75 65 55 - -
CYLINDER HEAD
TEMPERATURE (Fo)
MINIMUM 240 240 240 240 240 - 200
NORMAL 300-400 300-380 300-380 300-350 300-350 - 200-250
MAXIMUM 460 460 380 380 380 - -
GENERAL.
The minimum fuel grade for this engine is lOOLLIlOO. In case the
octane rating required is not available, use a higher rating. Never
use a lower rated fuel.
WARNING ... The use of a lower octane rated fuel can cause
pre-ignition and/or detonation which can ruin an engine the first
time high power is applied. This would most likely occur on
takeoff. If the aircraft is inadvertently serviced with the wrong
grade of fuel, then the fuel must be completely drained and the
tank properly serviced.
7
PREST ARTING.
Before each flight the engine and propeller should be examined for
damage, oil leaks, security and proper servicing.
3. See that fuel tanks contain proper type and quantity of fuel.
STARTING.
8
7. Throttle - Set to approximately 1000 RPM position.
2. Throttle - Open.
9
10. Oil Pressure - Check. If no oil pressure is noted within 30
seconds (60 seconds in cold weather), shut down the engine and
investigage.
10
3. Perform all ground operations with cowling flaps, if any,
wide open, with mixture control in "FULL RICH" position and
propeller governor set for maximum RPM (except for brief testing
of governor controls).
11
Minor spark plug fouling can usually be cleared as follows:
3. Mixture - Move toward idle cutoff until RPM peaks and hold
for ten seconds. Return mixture to full rich.
4. Magnetos - Recheck.
12
than 80 psi, the engine is warm enough for takeoff. Oil pressure
should not exceed 80 psi on takeoff.
6. Instrument Indications.
13
with no battery load indicates leak or malfunction m the
alternator or regulator system.
TAKEOFF.
14
In cold weather, the wastegate valve may not open unless the oil is
warm.
WARNING ... Overboosting will ruin the engine and be cause for
engine replacement.
NOTE ... Fuel flow during part throttle operation will usually be
slightly higher than required. Although this extra richness is not
harmful, it may be desirable to adjust the mixture control to
achieve the exact fuel flow as specified in the Cruise Control
15
Charts (Section IV). When the mixture is leaned during climb
operation, use at least 147 pounds at 75% NRP.
WARNING ... At power settings above 75% NRP, do not use the
E.G.T. gauge as an aid to mixture adjustment. If you attempt to
determine the "peak" E.G.T. while the engine is operating at high
power, the result may be burned valves, detonation, and possible
engine failure.
CRUISE.
16
4. If it is necessary to retard the throttle at altitudes above
10,000 feet, leaning of the fuel mixture may be required. Reset
mixture to the richer setting before the throttle is returned to the
high power position.
DESCENT.
LANDING.
17
NOTE ... Advance mixture slowly toward "FULL RICH". If
engine roughness occurs, as may happen at very low throttle
settings and high RPM, it may be desirable to leave the mixture
control approximately 3/4 open until the throttles are advanced
above 15 inches of manifold pressure.
STOPPING ENGINE.
NOTE ... Taxi time after landing may be considered part of five
minutes.
18
~~~~.--~-~--------------------------------------
SECTION III
ENGINE ROUGHNESS.
19
If engine roughness does not disappear after the above, the
following steps are to be taken to evaluate the ignition system.
TURBOCHARGER FAILURE.
20
-"
----==~-~===.~~~~---~-~~~~
21
NOTE ... An interruption in fuel flow to the engine will result in
turbocharger "run-down". At high altitude, merely restoring fuel
flow may not cause the engine to restart, because without
turbocharger boost, the mixture will be excessively rich. If the
engine does not fire, there will be insufficient mass flow through
the exhaust to turn the turbine. This condition may lead one to
suspect a turbocharger failure; however, employment of the
proper procedure will not only restart the engine, but will confirm
whether the turbocharger has failed. If loss of power is
experienced following surging 'of RPM, fuel flow, and manifold
pressure, the following steps are recommended.
22
ABNORMAL ENGINE INSTRUMENT INDICATIONS
3. Airspeed - Increase.
23
below 30 PSI, an engine failure should be anticipated and the
aircraft manufacturer's instructions for such should be followed.
IN-FLIGHT RESTARTING.
3. Magnetos On.
24
4. Throttle One-third (1/3) open.
3. Magnetos On.
25
NOTE ... If propeller has not been feathered, adjust to normal
cruise PM.
26
SECTION IV
27
~---~ --~---
Gauge fuel flow should fall between the maximum and minimum
values on the chart. If not, the fuel injection system or
instrumentation (including tachometer, manifold pressure, fuel
flow gage or EGT system) should be checked for maladjustment or
calibration error.
28
ci 40
J:
~
!:iw 36
FULL THROTTLE - ADMP
7
a:
<>-
32
/ V 380
I"~/v
Z
«
::;!
.
V -J
--
28 \.01"0 .- 360
>-
"v.~~ ~~~
a:
0
v.i
en
«
24
_v
~~y.~o
/;0\..'<- / 340
20
«'u\..\.. I 320
a:
w
~
/' ,ij <>-
w
en
----- ./ /) 300 0
a:
gvJ/
~-
J:
w
.>'
280 «
----
i
I
9 --- -- 260
a:
en
.700 - ---
/
/ ---- ---- 240
~ .650 .--- - / ~ --
ii: V ~~fC ---- VI
-----
J: -:::;: t .-
en _ "(I-\~011\.1 ./
enen .600 - I 7'
....J
~ f\l\.\.
I _B~ I
PV.OP \.0",0 . -
~ .550
o
u
....J
~ .500 - - ------ -- --- --- --- - -
u..
fil.450 - - - -- - -
3;
29
260~,TI.~mmmn~mm~~~~~~~~mm~~~~~~~rl
J
250 1 I,
::1-
; l'
j - -. t -- --+---+----+----+---+--+----+~___If__l_l__l_____H
: i I /
240
j -- -)---I--+-' -t--t----t-----l----t--+--+++-+---B
230 j _
,! I
--+-+--+
i---t---t-+--t---t----IIV-I-/-t-----a
I
Ii Ii
220
j ----- t-- 1-- I
L--+---+, --+---+---+--+!d:---1J;
210 -+-
- -- t - -
iii
--~-
i7 ~
200
r-,-t . /J}lf---I--------+------I::j
cr: 190 r-1--l-+--4-~~-~-~-~~+--+-+--a
:J:
en
~ 180 --
I I
---~-~-~-~-~-~-~~~--~~-~--~-a
/1
I
15 170
V;'
~
-'
U-
-'
Minimum
w 160 : j- -t-----+---+---+---1f----j-1f-/-F--P.... Allowable
=>
U-
I j' I / j . Furl Flow
J -+---+- ~
Minimum Ac~ePtable -7/ ') "--Approx. Best Power
150 I I
140
J. Fuel Flow Without
'E. G. T.
h_
~ /v...~(:)~
1
I!
I
J
1
iI r ~~
When the Exhaust Temperatures
90 i
I
I 17 55% Tt Rit
Show Minimum 50 0 F.Drop on
Sidle of jeak., ,
80 L-~··'ll":~I··~'~lll:rt'lliwllillillllwmilluwmmnwrlmmmmwmmmmwnw~mwmmnmmm~~
140 180 220 260 300 340 380
BRAKE HORSEPOWER
30
SEA LEVEL PERFORMANCE ALTITUDE PERFORMANCE
.,., . COOLING
I." ~. 1 - ,. 60 IN HzO I
, ~oc n~::~~::,:~:cLT,U~~::Ttn
1 Lrx;IIP ... Io ....... AO .. SLCH ... AT'n·U·'
T
f---+-+-~--j.---l
I Imln'~)(CEPT FOR
OROP .
-+-"; -r- HJRSE~owlR OB!~~NA~~~S"'NTE~~~~n\E~RESSURE
~ ~~;~Si I~~ ~:~~~ 5~: :~~:::::"T ,we' I I
b~~:MAMD~~':,~~'~!~!·,A5l1:::~::~~ws f---+-+~t---;- f- 'Tf1 pill Ir'l':=r::~~.,~~;~. iii ii' I
380 ' I RATING 38 __ •
I '''r'':;:t~:I,~::"t·;' . o"" /b' I::: r, I ,'uous .'
.'I. I· :! ..
' . ,, . : '1
00 RPM HG. MAX. CONTIN
I~.' ~r '.'• i -::.''''''~.~..
' ~-:•• """o;~6 _~ _ J
'
v...;
'i:',,
340
360
.,
R-.
.,. ---'
j- ~ , !- ... '...~J
300
' ---t '..
m ' . -- ...
300
.. ._ ....
. I' . ., ,
. . ..- .- 325 IN. HG.
MAX_C~R......, - ---
,-1,.
..J
I"
260
_." . "
, . ,
'50
240 ~
t : :.'~-"------..I
2'0 220
--t--£l'oo 200
t_180 180
.. t--1:l160 160
-". ·,,0
140 ~E ·~o
~ 1·-r"l120 s I
~ " "
16 18 20 26 30 32 34 36 38 40
'2 '4
ABS. DRV MANIFOLD PRESSURE IN HG
"
. PRESSURE AL TlrUOE IN THOUSANDS fEET
w
.....
Figure 3. Altitude Performance Curve
32
SECTION V
PREHEATING.
33
aids can be expected at temperatures below normal, provided the
aircraft battery is in good condition and the ignition and fuel
systems are properly maintained.
34
-- "--~"~---- - ._-- -------~------- --~-~------·------------"i
2. Hot air should be applied primarily to the oil sump and filter
area. The oil drain plug door or panel may provide access to these
areas. Continue to apply heat for 15 to 30 minutes and turn the
propeller, by hand, through 6 or 8 revolutions at 5 or 10 minute
intervals.
NOTE ... Since the oil in the oil pressure gauge line may be
congealed, as much as 60 seconds may elapse before oil pressure is
indicated. If oil pressure is not indicated within one minute, shut
the engine down and determine the cause.
35
5. Run the engine at 650 RPM until some oil temperature is
indicated. Observe oil pressure closely during this time and be
alert for sudden increase or decrease, indicating possible congealed
oil in the system. Retard throttles, if necessary, to maintain oil
pressure below 100 PSI. If oil pressure drops suddenly to less than
30 PSI, stop the engine and check for blown lines, filter, or cooler.
If no damage or leaks are noted, preheat the engine for an
additional 10 to 15 minutes before restarting.
36
pressure. Oil pressure should be steady and within limits during
this time. Observe the usual precautions to prevent overboosting.
NOTE ... Fuel flow will likely be on the high limit; however, this
is normal and desirable since the engine will be developing more
horsepower at substandard ambient temperatures.
3. Mixture - Rich.
4. Throttle - Open.
7. Starter - Engage.
NOTE ... Before apply power for takeoff, double check that oil
pressure, oil temperature, and cylinder temperature are well within
37
the normal operating range. When full power is applied for
takeoff, insure that oil pressure is within limits and steady. Surging
or overshooting of manifold pressure, RPM, or fuel flow may
indicate the engine is not satisfactorily warmed up.
e. Engine roughness.
38
These are: (1) Starting a hot engine, (2) Ground operation under
high ambient temperature conditions, and (3) Takeoff and initial
climbout.
39
-~~~~~~------------~
40
SECTION VI
ENGINE DESCRIPTION
OIL SYSTEM.
The oil supply is contained in a 13-quart, wet sump oil pan which
is attached to the bottom of the crankcase. A conventional
dipstick is provided for determining the oil quantity.
When the engine is turning, oil is drawn through a screen and pick
up tube which extends from the sump to a port in the crankcase.
It then passes to the inlet of the gear-type, engine-driven oil pump
and is forced under pressure through the pump outlet.
hicorporated in the oil pump is a pressure regulating relief valve
which prevents excessive oil pressure by allowing excess oil to be
returned to the suction side of the pump. After exiting the pump,
the oil (now under pressure) enters a full-flow filter and is passed
on to the oil cooler. If the filter element becomes blocked, a
bypass relief valve will open to permit unfiltered oil to flow to the
engine. As the oil enters the oil cooler, it will flow in one of two
directions: (a) When the oil is cold, an oil temperature control unit
41
42
will open and most of the oil will bypass the cooler. (b) As the oil
warms, the oil temperature control unit actuates to close off the
cooler bypass forcing the oil to flow through the cooler core. In
operation, the oil temperature control unit modulates to maintain
oil temperature in the normal range of approximately 170 F. 0
After leaving the cooler, the oil enters the crankcase where the
various channels and passageways direct it to the bearing surfaces
and other areas requiring lubrication and cooling. The propeller
governor boosts engine oil pressure for operation of the propeller.
It controls oil pressure going to the propeller hub to maintain or
change propeller blade angles. This oil flows through the propeller
shaft to reach the hub.
Other areas within the engine receiving oil include the valve lifters,
inner piston domes and lower cylinder walls. A tap in the side of
the crankcase supplies oil pressure for lubrication of the
turbocharger bearings. This oil is carried to the turbocharger
through an external line. After lubricating the turbocharger
bearings, it is drawn into a scavenge pump and forced back to the
oil sump. Oil within the engine drains, by gravity, back into the
sump.
FUEL SYSTEM.
43
~
~
VAPOR EJECTOR
VAPOR RETURN - ~_
...
PUMP INLET SUPPLY - ?f - -:
PRESSURE REGULATOR
--- --
~I MIXTURE RETURN
TURBO DISCHARGE
FUEL PRESSURE GAUGE
(NOZZLE PRESSURE)
FUEL PUMP
DECK PRESSURE
UNMETERED FUEL -
t, ,
iLMETERING UNIT I.i
___
,~--
METERED FUEL
--~
(a) In the idle cutoff position, the mixture control diverts all fuel
received back to the pump inlet or aircraft fuel supply. In this
manner, no fuel can flow toward the fuel injector nozzles.
The manifold valve receives fuel from the metering unit. When fuel
pressure reaches approximately 3.5 psi, a check valve opens and
admits fuel to six ports in the manifold valve (one port for each
fuel nozzle line). The manifold valve serves to proportion the fuel
evenly to each injector nozzle, and to provide a clean cutoff of
fuel to the cylinder when the engine is. shut down.
The injector nozzle lines connect the manifold valve to the six fuel
injector nozzles.
The injector nozzles (one per cylinder) are "air bleed" type fuel
nozzles which spray fuel directly into the intake port of the
cylinder. When the engine is running, flow through the nozzle is
continuous and will enter the cylinder combustion chamber when
the intake valve opens.
Since the size of the fuel nozzles is fixed, the amount of fuel
flowing through them is strictly a function of how much pressure
is applied. For this reason, fuel flow may be accurately determined
by measuring the pressure at the manifold valve.
45
All of the items described above are interdependent on each other
to meter the correct amount of fuel according to the power being
developed by the engine.
INDUCTION SYSTEM.
The filter normally accepts all incoming air from the aircraft
intake scoop. Should the filter become blocked for any reason, the
alternate air door will open to preclude engine stoppage.
46
LEGEND
¢::I•• RAM AIR
¢::I AIR
<=~ EXHAUST GAS
- HYDRAULIC OIL
COMPRESSOR
TURBINE
VARIABLE SETTING
ABSOLUTE PRESSURE
CONTROLLER .
~ TO CABIN
~
"-.J
The cylinder intake ports are cast into the cylinder head assembly.
Air from the spider manifold is carried into the intake ports,
mixed with fuel from the injector nozzles, and enters the cylinder
as a combustible mixture when the intake valve opens.
TURBOCHARGER.
TURBINE
COMPRESSOR WHEEL
WHEEL
EXHAUST
AIR INLET DISCHARGE
48
speed and resulting in more output of induction air from the
compressor, since it is connected to the opposite end of the
turbine shaft. Now, as the compressor output increases, manifold
pressure increases. The aneroid unit on the controller senses
compressor discharge pressure and its action opposes, the force of
the spring, that is, it tends to open the valve, relieving oil pressure
in the wastegate actuator which allows the wastegate to move
toward open. In operation, the forces between the spring and the
aneroid are balanced and the controller serves to maintain
constant compressor discharge pressure as selected by the throttle
and therefore maintains a constant manifold pressure. When the
throttle is repositioned, the cam, spring, aneroid and wastegate are
displaced until the forces are again in balance for the new
com pressor discharge pressure.
CYLINDERS.
49
~~~--~~--~=--~--.-.-- --"---.-~~~---
VALVES.
IGNITON.
(a) When the aircraft starter switch is operated, the left and right
magneto primary breaker points are grounded to prevent the
magnetos from producing ignition at the normal advanced timing
causing the engine to kick back, only the retard breaker points are
functioning.
50
(b) The starter switch also energizes a battery-powered starting
vibrator which supplies pulsating voltage to the retard breaker.
(c) As the engine turns during cranking, the retard breaker points
open, and cause a "shower of sparks" at the left mangeto spark
plugs. This high intensity ignition occurs later than would normal
ignition and promotes smoother engine starting.
(d) When the engine starts,and the switch is placed in the "Both"
position, the primary breakers are ungrounded, the starting
vibrator circuit is broken, and dual ignition is provided.
3 }--J]f'----,
L--r~ ________~____~________~~
3}---~~------~~--------~~--~
~--------------------~----------------~6
s}---------------------------J
LOWER SPARK PLUGS
51
52
SECTION VII
SERVICING.
Good common sense is still the rule, but certain basic maintenance
and operational requirements, that we find widely disregarded, do
determine, to a large degree, the service life of the modern aircraft
engme.
WARNING ... The use of a lower octane rated fuel can result in
destruction of an engine the first time high power is applied. This
would most likely oeeur on takeoff. If the aircraft is inadvertently
serviced with the wrong grade of fuel, then the fuel must be
completely drained and the tank properly serviced.
Oil: For initial fill, and for the first 25 h()ur~ of engine operation,
the lubricating oil shall conform to MIL-C-6529, Type II,
Corrosion Preventive Aircraft Engine Oil.
53
After the first 25 hours of operation and rings are seated, a
detergent oil conforming to Teledyne Continental Motors
Specification MHS-24B shall be used.
54
Sinclair Oil Company Sinclair Avoil
Exxon Company, U.S .A. Exxon Aviation Oil EE
BP Oil Corporation BP Aero Oil
Quaker State Oil & Quaker State
Refining Company AD Aviation Engine Oil
Delta Petroleum Company Delta Avoil Oil
Union Oil Company of California Union Aircraft Engine Oil HD
Gulf Oil Company Gulfpride Aviation AD
Phillips Petroleum Company X/C Aviation Multiviscosity Oil
SAE 20W-50
INSPECTIONS.
·Before each flight the engine and propeller should be examined for
damage, oil leaks, proper servicing and security. Ordinarily the
cowling need not be opened for a daily inspection.
55
Record any values not conforming to engine specifications so that
necessary repair or adjustment can be made.
Perform all items listed uner 50 Hour Inspection, and add the
following:
56
2. Cylinders, Fins, Baffles: Inspect.
57
14. Adjustments & Repairs: Perform service as required on
any items found defective.
58
SECTION VIII
TROUBLE SHOOTING
59
'"o This trouble shooting chart is pro\·ided as a guide. Review all probable causes given, check other listings of
troubles with similar symptoms. Items are presented in sequence of the approximate ease of checking, not
necessarily in order of probability.
TROUBLE SHOOTING CHART
b. Have gauge pressure - b. Turn off auxiliary pump and ignition switch,
Engine flooded. set throttle to "FULL OPEN" and fuel
control to "IDLE CUTOFF", and crank
engine to clear cylinders of excess fuel.
Repeat Starting procedure.
c. Have gauge pressure - c. Check for bent or loose fuel lines. Loosen one
No fuel to engine. line at fuel nozzle. If no fuel shows replace
fuel manifold valve.
2. Engine starts a. Inadequate fuel to a. Set fuel control in "FULL RICH" posmon,
but fails to fuel manifold valve. turn auxiliary pump "ON", check to be sure
keep running. feed lines and filters are not restricted. Clean
or replace defective components.
b. Defective ignition b. Check accessible ignition cables and connec-
system. tions. Tighten loose connections. Replace
defective spark plugs.
3. Engine runs a. Improper idle mixture a. Readjust idle setting. Tighten adjustment
rough at idle. adjustment. screw to richen mixture and back off
adjustment screw to lean mixture.
b. Fouled spark plugs. b. Remove and clean plugs, adjust gaps. Replace
defective plugs.
4. Engine has a. Idle mixture too lean. a. Readjust idle setting. Tighten adjustment
poor screw to rich en mixture and back off
acceleration. adjustment screw to lean mixture.
5. Engine runs a. Improper fuel-air mixture a. Check manifold connections for leaks. Tight-
rough at speeds en loose connections. Check fuel control and
above ide. linkage for setting and adjustment. Check fuel
filters and screens for dirt. Check for proper
pump pressure, and replace pump if defective.
c. Ignition System and spark c. Clean and regap spark plugs. Check ignition
plugs defective. cables for defects. Replace defective com-
ponents.
OJ.)
'"
0\
..J>. TROUBLE PROBABLE CAUSE CORRECTIVE ACTION
f. Fuel nozzles defective. f. Inspect fuel nozzle vent manifolding for.
leaking connections. Tighten and repair as
required. Check for restricted. nozzles and
lines and clean and replace as necessary.
7. Low Fuel a. Restricted flow to fuel a. Check mixture control for full travel. Check
Pressure. metering valve. for restrictions in fuel filters and lines, adjust
control and clean filters. Replace damaged
parts.
b. Fuel nozzle vent system b. Check venting system for leaks at connections
defective causing improper and other defects. Tighten connections and
pressure regulation. replace defective parts.
8. High Fuel a Hcstricted flow beyond a. Check for restricted fuel nozzles or fuel
Pressure. fuel control assembly. manifold valve. Clean or replace nozzles.
Replace defective fuel manifold valve.
b. Defective relief valve b. Check fuel injector pump control line from
operation in fuel injector. turbocharger for loose connections and
defects. Tighten connections, replace
0- damaged line.
VI
0-
0- TROUBLE PROBABLE CAUSE CORRECTIVE ACTION
c. Restricted r~circulation c. Replace pump.
passage in fuel injector
pump.
9. Fluctuating a. Vapor in fuel system, a. Normally operating the auxiliary pump will
Fuel Pressure. excess fuel temperature. clear systems. Operate auxiliary pump and
purge system.
b. Fuel gauge line leak or b. Drain guage line and tighten connections.
fuel in gauge line.
10. Low Oil Pressure a. Insufficient oil in oil sump, a. Add oil or change oil to proper viscosity.
on Engine Gauge. oil dilution or using
improper grade oil for
prevailing ambient
temperature.
b. High oil temperature. b. Defective oil temperature control unit in oil
cooler restriction. Replace valve or clean oil
cooler.
c. Leaking, damaged or loose c. Check for restricted lines and loose connec-
oil line connections - tions, partially plugged oil filter and screens.
Restricted screens and Clean parts, tighten connections and replace
filter. defective parts.
11. Poor engine a. Engine getting fuel. a. Check fuel control for being in full "IDLE
idle cutoff. CUTOFF" position. ,Check auxiliary pump
for being "OFF". Check for leaking fuel
manifold valve. Replace defective com-
ponents.
12. White smoke a. Turbo coking, oil forced a. Clean or change turbocharger.
exhaust. through seal turbine
housing.
0\
-...l
68
SECTION IX
b. Fill the sump to the full mark on the dipstick gauge with
MIL-C-6529 oil which will mix with normal oil, which is suitable
as a lubricant, and will provide protection against corrosion.
69
3. Preparation for Service.
70
b. Re-spray each cylinder without rotating crank. To
thoroughly cover all surfaces of the cylinder interior, move the
nozzle or the spray .gun from the top to the bottom of the
cylinder.
71
72
SECTION X
GLOSSARY
BHP x 792000
Crank RPM x Displacement
73
CRITICAL AL TITUDE-The maXlmum altitude at which a
component can operate at 100% capacity. For example, an engine
with a critical altitude of 16,000 feet cannot produce 100% of its
rated power above 16,000 feet.
74
LEAN LIMIT MIXTURE-The leanest mixture permitted for a
given power condition. It is-not necessarily the leanest mixture at
which the engine will run.
75
-
76
SUMP-The lowest part of a system. The main oil sump on a wet
sump engine contains the oil supply.
77
~~~~--~===--=--==---~~~----~-------------~-.-- ...-.--------
10W30. In such cases, this oil is more stable and resists the
tendency to thin when heated or thicken when it becomes cold.
78