Professional Documents
Culture Documents
6 Shearing Stresses Kayma Gerilmeleri Turkce 31122020
6 Shearing Stresses Kayma Gerilmeleri Turkce 31122020
CHAPTER MECHANICS OF
6 MATERIALS
Ferdinand P. Beer
E. Russell Johnston, Jr.
John T. DeWolf
Shearing Stresses in
Beams and Thin-
Lecture Notes:
J. Walt Oler
Walled Members
Texas Tech University (Kirişlerde ve ince cidarlı
elemanlarda Kayma
Gerilmeleri 31122020)
Introduction
• Transverse loading applied to a beam results in
normal and shearing stresses in transverse sections.
(Enine yükleme sonucu enlemesine kesitte eksenel
kuvvet ile kayma gerilmesi meydana gelir.)
• Distribution of normal and shearing stresses satisfies
Normal ve kesme gerilmelerinin dağılımı aşağıdaki
koşulları sağlamaktadır.
Fx x dA 0
M x y t xz z t xy dA 0
Fy t xy dA V M y z x dA 0
Fz t xz dA 0 M z y x M
• When shearing stresses are exerted on the vertical
faces of an element, equal stresses must be exerted on
the horizontal faces. (Düşey doğrultuda kayma
gerilmesi meydana geldiğinde eşit büyüklükte gerilme
yatay düzlemdede meydana gelir. Tyx=Txy)
Shear on the Horizontal Face of a Beam Element (Kirişte yatay doğrultuda meydana gelen kesme kuvveti)
• Substituting,
VQ
H x
I
H VQ
Kayma akısı (shear flow) birim uzunluğa gelen q shear flow
kesme kuvvetidir.
x I
© 2006 The McGraw-Hill Companies, Inc. All rights reserved. 6-4
Edition
Fourth
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
Example 6.01
SOLUTION:
• Determine the horizontal force per unit length
or shear flow q on the lower surface of the
upper plank. Üst ahşap bloğun alt yüzeyinde
birim uzunluk başına yatay kesme kuvveti veya
kayma akışını q belirleyin.
A beam is made of three planks, nailed together. Knowing that the spacing
between nails is 25 mm and that the vertical shear in the beam is
V = 500 N, determine the shear force in each nail.
(Ahşap 3 adet eleman çiviler ile birleştirilerek kiriş imal edilmiştir. Çiviler
arasındaki mesafe 25 mm dir. Kirişin maruz kaldığı kesme kuvveti 500 N. Her
bir çiviye etkiyen kesme kuvvetini bulunuz.)
Example 6.01
SOLUTION:
• Determine the horizontal force per unit length or shear
flow q on the lower surface of the upper plank. Üst
ahşap bloğun alt yüzeyinde birim uzunluk başına yatay
kesme kuvveti veya kayma akışını q belirleyin.
VQ (500 N)(120 10 6 m3 )
q
I 16.20 10-6 m 4
Q Ay
3704 N
0.020 m 0.100 m 0.060 m m
Shearing Stresses txy in Common Types of Beams (Belli kiriş tiplerinde txy kayma gerilmeleri)
VQ 3 V y 2
t xy 1
Ib 2 A c 2
3V
t max
2A
VQ
t ave
It
V
t max
Aweb
Cisimlerin
mukavemeti
kitabından
(Orijinal kitabın
Türkçe çevirisi)
Vmax 3 kips
M max 7.5 kip ft 90 kip in
Fx 0 H D C dA
a
• Except for the differences in integration areas, this is
the same result obtained before which led to
Entegrasyon alanlarındaki farklılıklar dışında, bu, daha
önce elde edilen sonuçla aynıdır.
VQ H VQ
H x q
I x I
Example 6.04
SOLUTION:
• Determine the shear force per unit
length along each edge of the upper
plank. (Birim uzunluğa etki eden
kesme kuvvetini üst kısımdaki ahşap
elemanın her bir kenarı için
bulunuz.)
A square box beam is constructed from four
planks as shown. Knowing that the spacing • Based on the spacing between nails,
between nails is 1.75 in. and the beam is subjected determine the shear force in each
to a vertical shear of magnitude V = 600 lb, nail. (Çivilerin arasındaki mesafeyi
determine the shearing force in each nail.
dikkate alarak, her çiviye etkiyen
(Bir kare kutu kiriş, gösterildiği gibi dört tahtadan kesme kuvvetini bulunuz.)
yapılmıştır. Çiviler arasındaki mesafenin 1.5 inç
olduğunu ve kirişin V = 600 lb büyüklüğünde bir
dikey kesme kuvvetine maruz kaldığı bilinerek,
her çivideki kesme kuvvetini belirleyin.
Example 6.04
SOLUTION:
• Determine the shear force per unit length along each
edge of the upper plank. (Birim uzunluğa etki eden
kesme kuvvetini üst kısımdaki ahşap elemanın her
bir kenarı için bulunuz.)
q
VQ 600 lb 4.22 in 3
92 .
3
lb
I 27.42 in 4 in
q lb
f 46.15
2 in
For the upper plank, edge force per unit length
Q Ay 0.75in.3 in .1.875 in .
• Based on the spacing between nails, determine the
3
4.22 in shear force in each nail. (Çivilerin arasındaki
mesafeyi dikkate alarak, her çiviye etkiyen kesme
kuvvetini bulunuz.)
For the overall beam cross-section,
lb
1 4.5 in 1 3 in F f 46.15 1.75 in
I 12 4
12
4
in
27.42 in 4 F 80.8 lb
VQ
H x
I
• The corresponding shear stress is (Karşılık gelen kayma
gerilmesi)
H VQ
t zx t xz
t x It
• Previously found a similar expression for the shearing
stress in the web (Daha önce gövdedeki kayma
gerilmesi için benzer bir ifade bulunmuştu.)
VQ
t xy
It
• NOTE: t xy 0 in the flanges
t xz 0 in the web
VQ
q tt
I
3 1 yY2
Px M Y 1 2
2 3c
• The section becomes fully plastic (yY = 0) at the wall when Kesit
duvarda tamamen plastik olduğunda (yY = 0)
3
PL M Y M p
2
• Maximum load which the beam can support is Kirişin destekleyebileceği
maksimum yük
Mp
Pmax
L
© 2006 The McGraw-Hill Companies, Inc. All rights reserved. 6 - 22
Edition
Fourth
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
3 P y 2
t xy 1 where A 2byY
2A 2
yY
3P
t max
2 A
• As A’ decreases, tmax increases and may
exceed tY
A ’azaldıkça, tmax artar ve tY‘ yi aşabilir.
© 2006 The McGraw-Hill Companies, Inc. All rights reserved. 6 - 23
Edition
Fourth
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
SOLUTION:
• For the shaded area, Taralı alan için
Q 4.31in 0.770 in 4.815 in
15.98 in 3
Unsymmetric Loading of Thin-Walled Members (İnce cidarlı elemanların simetrik olmayan yüklemesi)
My VQ
x t ave
I It
My VQ
x t ave
I It
Unsymmetric Loading of Thin-Walled Members (İnce cidarlı elemanların simetrik olmayan yüklemesi)
• If the shear load is applied such that the beam does not
twist, then the shear stress distribution satisfies (Kuvveti
nereden uygularsak kesitte dönme meydana gelmez?)
VQ D B E
t ave V q ds F q ds q ds F
It B A D
F h Ve
1. Q bulunur. • Combining,
2. q bulunur.
b 4 in.
3. F bulunur. e e 1.6 in .
h 6 in .
4. E bulunur. 2 2
3b 34 in .
© 2006 The McGraw-Hill Companies, Inc. All rights reserved. 6 - 27
Edition
Fourth
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
Example 6.06
• Determine the shear stress distribution for V = 2.5 kips.
V=2.5 kips için kayma gerilmelerini belirleyelim.
Az önceki sorunun devamı olarak
q VQ
t kuvvet kayma merkezine etkiyor.
t It
• Shearing stresses in the flanges, Başlıklardaki kayma gerilmesi
VQ V h Vh
t st s
It It 2 2I
Vhb 6Vb
tB
12
2 1 th2 6b h th6b h
62.5 kips 4 in
2.22 ksi
0.15 in 6 in 6 4 in 6 in
• Shearing stress in the web, Gövdedeki kayma gerilmesi
t max
VQ V 8 ht 4b h 3V 4b h
1
It 1 th2 6b h t 2th6b h
12
32.5 kips 4 4 in 6 in
Q
bth th 2
th
(4b h) 3.06 ksi
2 8 8 20.15 in 6 in 6 4 in 6 in
© 2006 The McGraw-Hill Companies, Inc. All rights reserved. 6 - 28
Edition
Fourth
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
Eğilmeden
Burulmadan