Professional Documents
Culture Documents
SH 8
SH 8
Maintenance
501-76741 CARTCABLE 1
503-37549-02 BRAKERUBBER 6
2. Important PARTS
031-02807 BE,ARiNIG 1
503-35821-02 STOPPER I
s03-36392-01 BEAzuNG 1
503-36392-02 BEARiNG 1
503-35549 STOPPER 1
3. 'I-Le another
4. Irriaging urrit
- 113 -
8.2 The items of the periodic maintenance
Check period
Reference
114
t
t
8.3 Error code,.'
some abnormality happens, the indicator \ " is lit up and error codeb
" is displayed on the
t@ If
control panel. All the X-ray emission is prohibited in this occasion. Cut off
power and tum it on
:
again.
Varuow)
For fi.equent lighting of indicatot' " \", any abnonnalitl' of the unit is suspected- Contact us
yttithout delay.
When temperature of the X-ray generator goes up due to manl' hours of use, X-ray emission is
limited to protect X-ray tubc and indicator "
I " is lit up ard solne enor code is displayed on the
control panel. In this case, cut off porver and wait f or temperature of the X-ray generator to fall
' .,\. down.
R
€r, .fable Error Code (Refer to connection of \YHA COi\rT-5O, 503-02E45 13/1?
Explanalion
115 ,
8.4 Check of the tube voltage and tube current
i)InthefinishedX-rayhighvoltageunit(ADl10P-50C+AD110P-50H)ofthewHA-
be measured using a high voltage
50NS, the tube voltage and tube current cannot
measuring instrument from the ourside'
ard inspection
2) Method to measure thc tube voltage and tube culTcnt in maintenance
a) Fili in the in.spection result shect NOHl-1-124, and storc it (QA division)'
I b) Measurcment Points
2o mA Ripple (kV)
(16)
40kV-3rnA Ir4onitor voltage (V) - TKV rvavelorn't
I (q) -
I
l- tlok\r-3
mA ARaciiography tubc clrr-lent C/) - TN4A wavefom.t
L t totv-o ,re Fluoroscopy Lube curent (V) - AN4A rvavelbrn-l
1
I
I
I
l"' ,116-
-ffit','
i&is...*,, - - .
For maintenance and inspection, the tube
voltage and tube curent are measured by monitoring
ii)
the waveform at the check pins TKV' TMA and AMA'
For maintenance and inspection, measure the TKV, TMA and AMA vaiues using
the
voltmeter. Afler [hat, control the kV and mA values using this method'
rtl -
8.5 2.5 kW X-ray power supply
I When failure is detected in the 2.5 kW X-ray power supply (power unit) from the contents
the error code displayed, determine at which unit between the control unit and high voltage unit
of
failure has occurred. Then, replace or repair the defective unit in principle.
I the
a) At the factory, each part of the pow-€r unit is adjusted and inspected independent\,
ond shipnrcnt fr-otrt the warehouse.
I*hen the power unit is replaced at a local site, the operatiotls ntust be confu'mecl but
each trinuner provided inside the pow,e.r unit does not ltave to be adjustecl.
Howev,er, the risirtg edge of the tulte current x,avefornl must be checkecl usittg the
FVF and FVR ntodes because the intrin.sic impedance of the flarnent circuit in the
powerut'tit is u littl.e dffirent.
b) If the high voltage unit (PC j ) inside the power unit is detected as defectit,e, it cannot
be reStlaced at a local site. And yihen the PC3 is defective, the X-ray tLtbe ma1, fig
defecive ol.so.
c) \Yhen the guarantee period of the high voltage unit ADll0P--5H is not expired, w,e
i--t
ll
lpce'
i* rcol.{Tl
I
lwl -s0 I
lllll
L---t
8.5.2 Error signal circuit between the power unit and WHA CONT-$Q PC
Board
r-
Error signal circuit
r-l
:T,
\\rrr\ coNhso
fl,,,
| rr4l-
.r
I
"oN iHterril
rol
r-
N.illP
LL-
I
I
I -o-------l
+. tl
TO Nr
itOC+FOC -r Y
/t
7, CON'I <-__--\^l
IP
\F
117
Ir
LJ Vr EP
t' I
A9
IC19 P\\ri\4
CIRCUIT
: fJYrl
I
119 -
High voltage unit
rcB WHA CONT.SO
&
@ M
THERMALSMTCH
@ rH o\€R -=
H3 (error code) II
8.5.3 Error signal specifications among the power unit, WHA CONT-SO PC Board and
a -COM1 17 PC Board
H H H
FI lt H L - lsv Do\\t'l
;
I3 F3
F4
H
L
L
H
L
H
KV OVER
mASTOP
F5 L H L ROC, FOC
-tzl-
8.5.4 Troubleshooting in the power unit (control unit, high voltage unit)
When thc X-ray is emitted while operating the WHA-5ON/S control unit in the normal
method, FAULT I is lit and the eror code F6 or F7 (or F2, F3, F4 or F5 sometimes) is
displayed.
To detemine at rvhich unit betwee n the control unit and high voltage unit failure has occurred,
perform the following procedure.
-
Immediately after tum on the X-ray, FAULTT is lit and dre enor code F6 or F7 is displayed.
PC1
lH'
.rJ
n,
tl
Q:
ooo T
TP7 TPS
D64 TP6
llns:
EB TPlO
I lrru o
oo o Dl-1
JP4
fr,28 @ Dr2 _I
)
DZtS -f_- CS
@ DL3 DZI5 CI- cL [--
o
o Dtl : -]f
: -D- 6J
: -Cl
o TP27 ;
:
r'z::< r
----]
U^
L)
D7,21 -{ )
t22
I
l
I
Has tailure occurred in the hlament/tube current circuit?
Is the filament culrent sct signal (IFST) conect? Check tlie FVF va-lue sent from
IFST on the WHA CONT PC Board: Approximately 3 to 4.5V the p -COM117 PC Board.
between CP9 and CP1 ChCCK thE WHA COI.]-I'IFST
ckcuit.
'*i, i-/-
Chcck conneclron bctrveen the PC I and PC3 via the JP4 (C, CL and CS).
Is the fil:uneiit inverter clrive signal wavelorn outiut bctwecn TP5 aJId
Fluoroscc,py
h2= , 5., :id 50KV
\d el
I
,Ll I
[,l] t0 -1 .
1
t t \
I TP-5-TPZ7
s* I ;* n
t \ ' TPI-T?Z1
I
-t23 -
I
YES
I
\l/
I
I'
ffiavelorInsAarrdB)outputhtwcenthetermina-lsl(C)and3(CS)aSweu
I
a^s betrveen r1e tenninals I (C) a,6 2 (CL) of the connector JP y'rovided on the PCI PC Board?
:
:
. when the JP4 is disconnected, is approxirnately 25V ftVavcfonn
c) output?
lll= ): l'1
A{] l0 Fluoroscopy
50 kv
I
l
;=,
l
il
Betrveen C and CS
PC1
3(CS)
2(CL)
Fluororcopy
7, il
Hl=
AC
l'J
,t0 EE sorv
fr lr
Jr
lict*'een C irnd CL
---
-I-tie
leit fcnt srvitch is
tumed tln, but ilrc X-ra1'
is not cmiLtctl.
- t/.4 -
0
No failure is detected in the circuit on the
Check the FET (Ql, Q2) on the PCI using the resistance
::r--l meter of die tester.
^a Connect the +black lead rvire to the fin (base) of Q I ' Q2.
w
Corrnect the red lcad wire to the GND GP27). Measure the resistance.
Tlie resistance mcter indicates in ttre normal status (Resistance value: @ ).
G
D
S
G
D
S
Thc filunent circuit on t.tre l{3 and the X-ra1' tube inside
fre high l'olage unit are det'ective.
t
-r25-
_)
7
-\'
li,./
.'l
.'
,11
t.
t.
I
*.
'v *
I
I
rl
in the
YES
I l.(l -
I
Check the gate signal waveform in the main FET inverter.
1) Connect the synchroscope to the anode of the diode shown in the figure below.
,,-/ C\Uro
/\ I -
\! "
Anode of DZl6 Anode o{D21,5 DZ.16
Note: Makc surc to turn off the power before connecting the synchroscope.
r:.-:
H
THY
ffl:-;r
0,1 ! i, ill Main FET gate rvavelorm
I
+
I
= ZlkIlz
rw
121
I
I
are correct'
l) Gate wavelorm is not correct-
All gate waveforms
+ 2) Gate waveforms are not output at al[.
i,
l1
Resistor: 60 W, 100 C)
Flr-roroscopy
50 kv
'1
-'1
IU, ;/d
H I= IiJlJV
Al] Plil0 Wavetorm belween Tl and T2
{- Resistor: 60 W, 10Of)
I
Radiography
il 50 kV, 8 rnAs
,1
n i 11
i/
I
t
\_
r28
c
The main circuit FET is not defective.
. .:
'd
j
1
I
I
t
I
tBilV
-r29-
of the lA IBS system
8.6 Maintenance and inspection
Iris
Acrylic 19un
Fe 14mm IA inPut dose sT-1030
Cylinderical lens CCU
I
k\. rTL{
LLU
\ i SENSOR
(\
KV rrl --
'11- 7l-, 1t' 7 \'- 61 61 -
4mm 69 to 72 kV .
= 3mR/min
IA input Josc i6hi\r
CCUTPI voltage
7l
" r'&n\'
H-DOSE N.DOSE/Ii-IXJSE
N.DOSE
1-l stcps-'DiaPlragrn 2.3
( 1/3)
8 stcps
*Diaptu-agm i'3
1" (i/1.9)
22 steps-DtaPnragm J.o
9" ta*Pt 'DiaPtrragrn 2'6
,-ii
130 -
8.6.1 Problems in the IBS system using the CCD camera
t 1) In the WHA-50, the IA adopts the CCD camera whic,h has- the mech-ani9a]rotationmechanism.
Accordingly, it is diff,rcult to disassemble the IA at a local site, and the luminance of the output
fluorcscent screen in the view point of the IA independently can be hardly measured.
I
2) It is known that the sensitivity of the CCD camera is hardly deteriorated. The aging
deterioration of the luminance of the IA can be managed using the CCD camera.
I
a) The standard of the sensitivity of the IBS system is such that the video signal at the test point
TPt in the CCU is 160 mV rvhen the input dose 3 mR/min is given to the IA.
b) The relation between 3 mR/min and 160 mV can be modihed using the iris. At the tirne of
installation, 8 steps (in 7 inch) or 16 steps (in 9 inch) is set by the DIP switch provided on the
IzuS CONT PC Board.
against the video signal 160 rnV. For example, this dispersion is represented in the
allorvable tubc voltage ra-nge 67 to 71 kV in the IBS balance point using thc 19 cm acrylic
object
It is recommended to record and store the IBS balance conditions at the time of instaliation. At a
periodical inspection, you can measure. thc voltage at TP1 under thc same condition.s rvith those at
installltion, cr you can obtain the change lincrease) in thc input X-ray quaniity require'J to
so rhat the kV balance value at the timc of installation can be assut'ed. If the initial kV balance
yalue cannot be achieved, it should be regalded thatthe sctvicc lit'e of the IA has tut-t or-rt to prevent
cxpo.sure d(),sc.
131
c) This "14 steps" is determined by the treld test'
3 mA is the maximum value in the normal
fluoroscopy, and 6 mA is the maximum value in the
for the boost fluoroscopy is as
boost fluoroscopy. Accordingly' when the number of steps
fluoroscopy' the same kV value a,d
almost as twice as the number of steps for the normal
in both normaLl fluoroscopy and boost
video signal at TP1 will be obtaincd for the same objrct
becomes almost twice, the S/N ratio is
fluoroscopy. And because the used dose exclusively
improved.
"l4
Actually, the suPer-shot, DSA and maximum value of
i2 mA arc considered, steps" is
adopted.
fluoroscoPY.
N-Dose rvidth
Several seconds later
I
Y
I
H-Do.se rvidti'l
Right foot srvitch is tumed on
I
I
when the lluoroscopy tube voltage become.s 101 kV- Retltnl.s
til
IO N-Dosc rvidt.h'
8.6.5 Reference
(relercncc Value)
1) Display siz.e of circlc blanliing on monitor FI-UO arcl n-ionitor I\4IrN'{ORY
t32
3) Deviation in the center of rotation of the CCU (reference value)
I
H.V.
/ 9" 10 mm or less
/ ,H
,H ta
7"
6"
10 mm or less
15 mm or less
i. "'-
The CCD camera unit is assernbled into the IA, and cannot be separatecl at a local siLt-.
l) If the lA becomes delective rvithin the gualantee pcriod, we rvel1 replace the IA zurd CCD
as one unit. After replacement, the IBS balance must be adlusted.
2) If the IA becomes ciet'ective alier thc guarantee period has expircd, sencl the IA and CCD as
"/i
t
133
8.6.7 First degree maintenance item
I
t 8.6.7.1 How to adjust the l'l' lens focus
I
I
i
I
1
1) How to adjust the I'I' focus
Hcragottscrckctlleadtloltforlockingthc.fVlcnsi.clcusandLlrefbcus
ad jLlsttllcnt ring are providcrl directly'
bclrlr"'thc shiclcl platc'
ttgl1go n 1n.\e1|E l,
"dl.
E
\1[p]css stcol disc
I
-N
-
I
O
l '1-- i{otation udt removtt-l screw
Photo inttemlPter
Relal'terminal btlard
t34
8.6.7.2 How to replace the l.l. parts
0
1) Replacing the CCD PC Board
Remove the CCD PC Board (mounted the stainiess steel disc to off'er engagementr)
rvith the disc.
Use 4-M3 screw. If a longer screw is used, the CCD PC Board will not nctate.
Make sure to use the attached screw. Never loosen the CCD PC Board mounting
screrv.)
- r35 -
8.6.7.3 Troubleshooting
[Ret'ercnce ligLrrcl
ApPcarance ol 7-inch I.l. Appearance of 9-inch I.l.
n,4
tlh
8.6.8 XTV: ST-10305D
,1
8.6.8.1 ST-10305D block diagram
SENSOR PCB
PROCE S S
: '(,i*'::.:'.
TPl -fP3 oTPs
. '.
$\-:'
-
H.CLIP I I GAIN SUB-GAI N
TM
DCC SETU? iCC SUB-S ETUP
TNX-N. SLI CE
DCC-LIUIT AGC-LixlT
RE cU Pq.( E etc
iBS out
{
(8
t31 -
8.6.8.2 ST-1030 adjusting point
NOTE: a) Items 8) and 11) are available t0 execute the adjustment at the installation site.
1) Circle Branking
Adjust the circie branking size to inscribed I.I out put image size to
inscribed rvith C-FI/V (aspect ratio), CIR-BL (size).
6) DCC adjustmeirr (A. KNEE is sct on, since that it will be kept ON)
Adjust VR A. KNEE CW dircction from CCW trULLY position, to gct
350 rnV on TP3 when TPI is at 240 mV.
Adjust VR:A. KNEE LIMIT to get 500 mV on TP3 When TPl is at 1.8V
and, at the samc peiiod, 1.3V is measured on TP5.
N4. KNEE is al.so adjusted in the sarr-re rvay, described above.
DCC
Gate OFF
U Ya
t* I aU BS'F.F
il li= llrBSoN
DCC
Gate ON
Ll l,l Ll IBS Gare oN A,
BOTTOM oIPCB
-138-
8) IBS area and gain
IBS area
0
\@
139 -
Adjuster name Function Comment
q
AGC AGC (ON/OFF) Process unit
IT I'NTEE
M- r\1 tLL Knee point set tdmmer rvhen DCC is turned off
€
Gatr: zu'ea adjustment trimmers lbr DCC (A. KNEE)
140 -
Adjuster namc Function
Comment
e
IBS circuit output DC adjustment trimmers
Mother board
.A. I.O . A. r. o (A_TBS.
O. S)
. .. . Offset of average circuit
*Note:
.P.r.o . P. L O (P-TBS. Abbreviation of
C.S)
panel indication
.... Offset of peak circuir
. A.I. G - A. r. G (A_TBS.
CAlr)
.... DC gain of average circuit ( ) indicate.s
.P.i.G . P. r. G (P-TBS. PC Board silk
GArN)
* Note larne.
.... DC gain of peak circuit
l
I
f:::
.A-IBS Modc ser srvircl.les for averagc (A-IBS) arrl peak (p_IBS)
I
I
detection l.
I
-t41-