Professional Documents
Culture Documents
Programmable Timers EZM-XX35 - Manual V05 01-17 - EN
Programmable Timers EZM-XX35 - Manual V05 01-17 - EN
59 inch
Panel Cut-out
EZM-4435,EZM-4935,EZM-7735,EZM-9935 65 mm / 2.56 inch (min)
Sensor OP
OP
SV
SV
EZM-7735
EZM-4435,EZM-4935,EZM-7735,EZM-9935 Supply Switch Fuse
adjusted in parameter.)
OUTPUT
Process Output : Relay Output( 5A@250V Vat Resistive Load)
SET RESET
P
DISPLAY :
Actual Value Display :
Position.
EZM-7735 : 8 mm Green 6 digit LED Display S2
5
48 mm / 1.89 inch
Dimensions:
EZM-4435 : (48 x 48mm,Depth: 95 mm) Timer OP EZM 5- Insert the mounting
-4 435
EZM-4935 : (96 x 48mm,Depth:96 mm) O2
SV
clamps to the holes that
EZM-7735 : (72 x72mm, Depth:95.5 mm) P
SET RESET
S2
located top and bottom
EZM-9935 : (96 x 96mm,Depth:96 mm) sides of device and screw
Time
Panel Cut-Out: r up the fixing screws until
P
EZM-4435 : (46 x 46mm) 48 mm / 1.89 inch
SET
RESE
T
the unit completely
11.5±1mm/0.45 inch 84mm / 3.31 inch immobile within the panel.
EZM-4935 : (92 x 46mm)
EZM-7735 : (69 x 69mm) 92mm / 3.62 inch(min)
EZM-9935 : (92 x 92mm)
Introduction Brochure. ENG EZM-XX35 01 V05 01/17
Accessing and Changing the Set Values :Output Functions (Default=0) Failure Messages in EZM-XX35 Programmable Timers
Main Operation Main Operation 6:Automatic Reset-4:When Main Operation Time Unit and
Screen SET Screen SET Screen Screen 0:Manuel Reset-1:Process Screen Password Screen Scale Selection
Reset and Set
Protection
O1 O1 O1 O1
SV
O2
SV SV
O2 O2
SV
happens.When count set value,output position is
S2 S2 S2 S2
value,Output position is
P
SET RESET
P
SET RESET
P
SET RESET
P
SET RESET
changed. counting will continue (for When PROG button Press ENTER By pressing ENTER Press PROG Continue to
is pressed,password button without button, user can see all button to exit press ENTER
0->P), if the start input is entering screen will entering the parameters except for from button for
WhenShift
b u t t o n i s Increase the flashing Save the SET value active output position appear. password. program password. programming
mode.
scanning the
parameters.
Pressed,4th digit digit with pressing the With pressing the
of Set value starts Increment Button. Enter Button. changes the old position
1:Manuel Reset-2:Process
to flash. at the end of the output
counts,until count value pulse time. Main Operation Time Unit and
reaches Set value.When Screen Scale Selection
Accessing to the Program Parameters count value reaches the
Main Operation Time Unit and Set value,Output position 7:Automatic Reset-5:Proces Timer Timer
Screen Password Screen Password Screen Scale Selection is changed.Counting counts,until count value SET RESET SET RESET
When Prog Button 4th digit of the password After entered the Press Enter Button Timer
is pressed,password parameter flashes.Enter password,press to access to 2:Manuel Reset-3:Process active then counting will SET RESET
SET
SET RESET
SET SET To remove this warning and reset the count value
changes the old position.
RESET RESET RESET
Note-1 Note-1 Note-1 Note-1 : Output Pulse Time (Default =00.02.00) press RESET button.
Press Enter Button Press Enter Button Press Enter Button Press Enter Button
to access to to access to to access to to access to It determines how long Output will be active.It can be adjusted
following parameter. following parameter. following parameter. following parameter.
3: Automatic Reset-1:When from 00.00.00 to 99.59.99 (99 minutes; 59.99 seconds). If it is
count value reaches the 00.00.00, then it operates indefinitely. Installation
Sensor Type Reset and Set
Data Record set value,output position is
c
Count Direction Selection Protection : Count Direction (Default =0) Before beginning installation of this product,
changed.Process value is
Upcount. ( 0 --> Preset ) please read the instruction manual and warnings
reset automatically and
Downcount. ( Preset --> 0 ) below carefully.
SET RESET SET RESET SET RESET SET RESET
counting will continue from
Note-1 Note-1 Note-1 Note-1
“0”(upcount) or “Set” In package ,
Press Enter Button
to access to
Press Enter Button
to access to
Press Enter Button
to access to
Press Enter Button
to access to (downcount) if the start : Data Record (Default =1) -One piece unit
following parameter. following parameter. following parameter. following parameter.
input is active after the Count value is saved to memory when power is -Two pieces mounting clamp
end of the output pulse disconnected and restored on power up. -One piece instruction manual
Program time,output position chan Count value is not saved to memory when power is
Password
Press Enter button to access to ges the old position. disconnected. A visual inspection of this product for possible damage occured during
the first program (Time Unit and : Sensor Type Selection (Default =0) shipment is recommended before installation. It is your responsibility
Scale Selection) parameter.
SET RESET
Note-1 to ensure that qualified mechanical and electrical technicians install
NPN sensor type selected.
4:Automatic Reset-2:When this product.
PNP sensor type selected. If there is danger of serious accident resulting from a failure or defect
Note 1- Parameter value can be changed with Incrament button. count value reaches the
set value,output position is : Reset and Set Protection (For Front Panel Access) in this unit, power off the system and the electrical connection of the
When the Enter button is pressed,parameter value will be saved (Default =0)
changed.Counting doesn’t device from the system.
and following parameter is accessed. No Reset and Set protection.
continue over or the set The unit is normally supplied without a power switch or a fuse. Use
value.Process value is Only Reset button protection is active. power switch and fuse as required.
Note 2- Press “P” button is exit without saving the parameter
r e s e t a u t o m a t i c a l l y. Only Set button protection is active . Be sure to use the rated power supply voltage to protect the unit
value. Thus Main Operation Screen is appeared.
Counting continue from “0” Full Protection.Reset and Set button protection is active. against damage and to prevent failure.
Parameter Definitions (upcount) or “Set” Keep the power off until all of the wiring is completed so that electric
(downcount) if the start is :Program Password (Default =0) shock and trouble with the unit can be prevented.
: Time Unit and Scale Selection (Default =0) active.Output position It is used for accessing to the program parameters. Never attempt to disassemble, modify or repair this unit. Tampering
changes the old position with the unit may results in malfunction, electric shock or fire.
Hour/Minute base counting timer. Do not use the unit in combustible or explosive gaseous atmospheres.
at the end of the output It can be adjusted from to .
It can be adjusted from 00.00 to 99.59 . During the equipment is putted in hole on the metal panel while
pulse time.
Minute/Second base counting timer. If it is ; there is no password protection while mechanical installation some metal burrs can cause injury on hands,
It can be adjusted from 0.00 to 99.59. entering to the program parameters. you must be careful.
5:Automatic Reset-3:When When programming button is pressed, will Montage of the product on a system must be done with it’s mounting
Second/Milisecond base counting timer.
count value reaches the appear on the display. clamp. Do not do the montage of the device with in appropriate
It can be adjusted from 00.00 to 99.99.
set value,output position is If this parameter is different from “ 0” and user wants mounting clamp. Be sure that device will not fall while doing the
Hour/Minute base counting timer. changed.Count value to access to the program parameters; montage.
It can be adjusted from 00.00 to 23.59. becomes zero (for 0->P) It is your responsibility if this equipment is used in a manner not
Hour base counting timer. counting restarts on “0” 1- If user does not enter the value correctly ; specified in this instruction manual.
It can be adjusted from 000.00 to 999.99 value,if the start input is operation screen will appear without entering to operator
Minute base counting timer. active,but set value is parameters. Garanti
It can be adjusted from 000.00 to 999.99 showen on the process Warranty
2- When in top display and in bottom
Second base counting timer. value screen.Output display,if user presses ENTER button without entering
position becomes the old EMKO Elektronik warrants that the equipment delivered is free from
It can be adjusted from 000.00 to 999.99. password (for observing the parameters): defects in material and workmanship. This warranty is provided for a
position end the real count User can see all parameters except Program Password but
: Reset, Pause and Start Input Pulse Time. period of two years. The warranty period starts from the delivery date.
value can be seen at the device does not allow to do any change in the program
(Default =50) This warranty is in force if duty and responsibilities which are
end of output pulse time. parameters.
It is used to protect against the electrical contact debounce determined in warranty document and instruction manual performs by
or the signal that is less than the determined pulse time. the customer completely.
It can be adjusted from to milisecond.
Maintenance
Repairs should only be performed by trained and specialized
personnel. Cut power to the device before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol,
Trichlorethylene etc.). Use of these solvents can reduce the
mechanical reliability of the device. Use a cloth dampened in ethyl
alcohol or water to clean the external plastic case.
Diðer
OtherBilgiler
Informations
Manufacturer Information:
Emko Elektronik Sanayi ve Ticaret A.Þ.
Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369
BURSA/TURKEY
Phone : +90 224 261 1900
Fax : +90 224 261 1912
Order Information
EZM-4435 ( 48x48 DIN 1/16) A BC D E / FG HI / U V W Z
EZM-4935 ( 96x48 DIN 1/8)
EZM-7735 ( 72x72 DIN )
EZM-9935 ( 96x96 DIN 1/4) 00 0 1 / 00 00 / 0 0 0 0
A Supply Voltage
E Output-1