Professional Documents
Culture Documents
PP 2
PP 2
Which of the following is the MOST suitable : Before work is drilled on an exact location,,
clothing to wear in the Workshop? the position of the hole MUST be
d S ? ' 'Air
(B) Foam
(C) Water Which of the following lathe tools should
(D) • Carbon dioxide be used to cut the shoulder ‘X’ in the sketch
above?
Which of the following is UNSUITABLE as
eye protection gear for use in the workshop? (A)' Facing
(B) Roughing
"(A) , Sunglasses (C) Finishing
(B) Cover goggles Round nose
(C) Eyecup goggles
(D) Spectacles with eye shield
When should oiling and greasing of a lathe
be carried out?
Which of the following hammer faces should
be well polished and free from scratches at I. After it is well cleaned
all times? II. After all swarf has been removed
III. After all metal particles have been
(A) Ball peen removed
Planishing
(C) Cross peen (A) I and II only
(D) Straight peen (B) I and III only
(C) ..II and III only
((D) I, II and III
Notching and clipping are done during sheet ‘
metal pattern development in order to
The MAIN purpose of the angular cut 13. Which of the following show how to test for
indicated on the tool shown above is to squareness and flatness?
(A) prevent the tool from rubbing
against the work
allow for the flow of chips
TO give the tool a sharp edgft Light
CD) allow for the free flow of cutting
fluid
(A) Rackand-pinion
(B) Quill
(C) Splines
(D) Clutch
m.
Item 11 refers to the following diagram.
(A ): I and II only
(B) I and III only
(C) II and III only
(D) ; I, H and III
When a steady rest is used, it is attached to 19. Cutting fluid is used to prevent excessive
the heating o f acutting tool and the workpiece
by
(A) tailstock
(B )' lathe bed (A) flushing away chips.
(C) binding lever (B) hardening the edges.
(D) clamping lever (C) creating excessive wear
(D) reducing heat generation
(A) 1.75
(B) 3.50
(C) 5.25
(D) 6.00
Item 18 refers to the diagram below showing 21. The lathe is used to remove material
three types o f gears A, B and C, meshing with continuously by rotating the
each other.
*(A ) work against a stationary cutter
(B) cutter against the work
(C) work against a cutter that travels or
feeds into or across it
(D) cutter as it feeds into the stationary
work
23. A metal pattern that is made and used for 27. Which ofthfe following mechanisms is used to
marking out a number of similar shapes is a connect a mechanical drive to aprime mover?
24. Which of the following tools are used in the Item 28 refers to the following diagram.
riveting process?
A
H.
-B
HI. £
28. The sketch above shows a clearance hole to be
made in Part A and a start in Part B, Which
IV. of the following procedures would be correct
to ensure that the start in Part B is in line with
the axis of the hole in Part A?
(A) I, II and III only
•^B) I, II and IV only (A) Drill a clearance hole in A and use
(C) I, III and IV only a small drill to spot into B.
(D) I, II, III and IV * (B) Drill a clearance hole in A and spot
into B.
(C) R em ove A and drill each
25. The tool used in bench work for chipping is separately.
: the (D) Remove A and spot drill into B.
Item 30 refers to the following diagram. 33. The MAIN purpose o f step pulleys on a
drilling machine, is to
■*(A) Screws/bolts
(B) Soft solder
(C) Arc welding
(D) Hard solder
(A) Reamer
(B) Twist drill
\C ) Cientre drill
(D) Countersink drill
37. Which of the following are stages in making Item 39 refers to the following diagram.
a wired edge?
C -
ill.
40. Step pulleys on the drill motor facilitate the
control o f
(A) noise
IV. (B) speed
^(C) power
(D) depth
42. The drawing above shows the features of 47. Maintenance that is planned for a specific
a twist drill. The flute is indicated by the time and date is known as
number
(A) unscheduled maintenance
'(A ) j
' (B) , scheduled maintenance
: ( B) II (C) direct maintenance
■'(C)- III *(D) plant maintenance
^(D) IV
(A) plant maintenance 49. In the drawing above, which of the following
(B) direct maintenance operations should FIRST be carricd out?
(C) industrial maintenance ;
(D) corrective maintenance (A) Braze the plate to the blade.
(B) Rivet the handle to the plate.
(C) Braze the handle to the blade.
^(D) Rivet the plate to the blade.
50. Which of the following seams is used 55. . Which of the following metals should NOT be
especially where strength in a joint is used for making vice clamps to.hold polished
required? Work?
51. The type of steel that should be used for 56. Which of the following is a ferrous material?
making hand files is
Brass
^ (A) high carbon • *(B ) Steel
(B) nickel alloy * (C) Copper
(O low carbon (D) Aluminium
(D^ high speed
53.- A metal is referred to as ‘non ferrous’ When Item 58 is based on the diagram below
it contains
59. A drill is raised occasionally when drilling a ( Ih an arc welding operation, a student got
hole in order to burned. The FIRST treatment that should be
applied is
rf(A) clear the hole of chips
(B) release the pressure slightly (A;) iodine
(C) prevent the drill from catching . (B) cold water
(D) see if the drill is running straight (C) warm water
(D) petroleum jelly
IF YOU FINISH BEFORE TIME IS CALLED, CHECK YOUR WORK ON THIS TEST.