Professional Documents
Culture Documents
ISO 286 - Limits & Fits
ISO 286 - Limits & Fits
Part 2:
Tables of standard tolerance grades and limit deviations
for holes and shafts
Par-tie 2: Tables des degrh de tokrance normalis& et des Qcarts limites des al&ages
et des arbres
Reference number
IS0 286-2 : 1988 (E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing International
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work.
This part of IS0 286 has been prepared by ISO/TC 3, Limits and fits, and, together
with IS0 286-1, completes the revision of ISO/R 286, IS0 system of limits and fits.
ISO/R 286 was first published in 1962 and subsequently confirmed in November 1964;
it was based on ISA Bulletin 25 first published in 1940.
The major changes incorporated in this part of IS0 286 are as follows:
a) The presentation of the information has been modified so that IS0 286 can be
used directly in both the design office and the workshop. This has been achieved by
separating the material dealing with the bases of the system, and the calculated
values of standard tolerances and fundamental deviations, from the tables giving
specific limits of the most commonly used tolerances and deviations.
b) The new symbols js and JS replace the former symbols j, and Js (i.e. s and S
are no longer placed as subscripts) to facilitate the use of the symbols on equipment
with limited character sets, e.g. computer graphics. The letters “s” and “S” stand
for “symmetrical deviation”.
c) Limit deviations have been included for basic sizes from 500 to 3 150 mm as
standard requirements (these were previously included on an experimental basis
only).
d) Limit deviations have been extended for holes H and JS, for shafts h and js, by
including tolerance grades IT17 and IT18 in all basic sizes, and, for experimental
purposes only, by including tolerance grades IT1 to IT5 in basic sizes over 500 mm
up to 3 150 mm.
e) Limit deviations have been extended for some tolerance classes used in fine
mechanisms and horology, in basic sizes up to 50 mm.
g) The principles, terminology and symbols have been aligned with those required
by contemporary technology.
Users should note that all International Standards undergo revision from time to time
and that any reference made herein to any other International Standard implies its
latest edition, unless otherwise stated.
Printed in Switzerland
ii
IS0 286-2 : 1988 (El
Contents Page
0 Introduction ........................................................ 1
1 Scope ............................................................. 1
3 References ......................................................... 2
7 Bibliography ........................................................ 3
...
III
INTERNATIONAL STANDARD IS0 286-2 : 1988 (E)
Part 2:
Tables of standard tolerance grades and limit deviations
for holes and shafts
0 Introduction IS0 286 covers values for the upper deviations ES (for holes)
and es (for shafts), and the lower deviations EI (for holes) and
The need for limits and fits for machined workpieces was ei (for shafts) (see figure 1).
brought about mainly by the inherent inaccuracy of manufac-
turing methods, coupled with the fact that “exactness” of size
NOTE - In the tables of limit deviations, the values for the upper
was found to be unnecessary for most workpieces. In order
deviation ES or es are shown above the values for the lower deviation
that function could be satisfied, it was found sufficient to
EI or ei except for tolerance class JS and js which is symmetrical about
manufacture a given workpiece so that its size lay within two
the zero line.
permissible limits, i.e. a tolerance, this being the variation in
size acceptable in manufacture.
With developments in industry and international trade, it The IS0 system of limits and fits provides a system of toler-
became necessary to develop formal systems of limits and fits, ances and deviations suitable for plain workpieces.
firstly at the industrial level, then at the national level and later
at the international level. It should be noted that the general term “hole” or “shaft” used
in this International Standard can be taken as referring to the
This International Standard therefore gives the internationally space contained by (or containing) the two parallel faces (or
accepted system of limits and fits. tangent planes) of any workpiece, such as the width of a slot or
the thickness of a key (see also IS0 286-l). Similarly, the term
A general graphical representation of the relationship between
“commonly used holes and shafts” shall be interpreted as pro-
the respective tolerance classes and their deviations is given in
viding a very wide choice of limit deviations suitable for a wide
the annex.
variety of requirements.
This part of IS0 286 gives values of the limit deviations for
commonly used tolerance classes (zones) for holes and shafts Notes on the presentation of tables 2 to 32 are given on
calculated from the information given in IS0 286-l. This part of page 7.
1
IS0 286-2 : 1988 (E)
- - -
Zero line
3 References Attention is drawn to the fact that the tolerance classes shown
in figures 2 and 3, and their limit deviations, given in tables 2
NOTE - See also clause 7. to 16, are not intended to give detailed directives on the selec-
tion of tolerance classes for any purpose. Recommendations
I SO 286-1, /SO system of limits and fits - Part 7 : Bases of for the selection of tolerance classes are given in IS0 1829.
tolerances, de via tions and fits.
NOTE - Some tolerance classes are only provided for a restricted
IS0 1829, Selection of tolerance zones for general purposes. range of basic size steps. For further information, see note 1 on page 7.
4 Standard tolerances
6 Limit deviations for shafts
The values of standard tolerance grades IT1 to IT18 inclusive
are given in table 1. A synoptic representation of the tolerance classes for shafts,
given in this part of IS0 286, is shown in figures 4 and 5.
For information on the bases of the system and its application,
see IS0 286-l ; for values of standard tolerances IT0 and ITOl, Attention is drawn to the fact that the tolerance classes shown
see IS0 286-1, annex A, table 5. in figures 4 and 5, and their limit deviations, given in tables 17
to 32, are not intended to give detailed directives on the selec-
tion of tolerance classes for any purpose. Recommendations
5 Limit deviations for holes for the selection of tolerance classes are given in IS0 1829.
A synoptic representation of the tolerance classes for holes, NOTE - Some tolerance classes are only provided for a restricted
given in this part of IS0 286, is shown in figures 2 and 3. range of basic size steps. For further information, see note 1 on page 7.
2
IS0 286-2 : 1988 (E)
3
IS0 286-2 : 1988 E)
Table 1 - Numerical values of standard tolerance grades IT for basic sizes up to 3 150 m m ‘1
NOTE - This table, taken from IS0 286-1, has been included in this part of IS0 286 to facilitate understanding and use of the system.
Tolerances
IJm mm
0,8 1 1,2 1 2 1 3 1 4 1 6 1 '0 1 14 1 25 1 40 1 60 0,l 1 0,14 1 0,25 1 0,4 1 0,6 1 1 1 1,4
1 I,5 2,5 4 5 8 12 18 30 48 75 0,12 0,18 0,3 0,48 0,75 I,2 I,8
61 IO 1 I,5 2,5 4 6 9 15 22 36 58 90 0,15 0,22 0,36 0,58 0,9 I,5 2,2
10 1 18 I,2 2 3 5 8 11 18 27 43 70 110 0,18 0,27 0,43 0,7 I,1 I,8 2,7
181 30 I,5 2,5 4 6 9 13 21 33 52 84 130 0,21 0,33 0,52 0,84 I,3 2,l 3,3
30 I 50 I,5 2,5 4 7 11 16 25 39 62 100 160 0,25 0,39 0,62 1 I,6 2,5 3,9
2 3 5 8 13 19 30 46 74 120 190 0,3 0,46 0,74 I,2 I,9 3 4,6
2,5 4 6 10 15 22 35 54 87 140 220 0,35 0,54 0,87 I,4 2,2 3,5 5,4
Hl JSl
H2 JS2
EF3 F3 =G3 G3 H3 JS3 K3 M3 N3 P3 33 s3
EF4 F4 =G4 G4 H4 JS4 K4 M4 N4 P4 34 s4
E5 EF5 F5 =G5 G5 H5 JS5 K5 M5 N5 P5 35 s5 l-5 u5 v5 x5
CD6 D6 E6 EF6 F6 =G6 G6 H6 JS6 J6 K6 M6 N6 P6 36 ;6 T6 U6 V6 X6 Y6 Z6 ZA6
CD7 D7 E7 EF7 F7 =G7 G7 H7 JS7 J7 K7 M7 N7 P7 37 s7 l-7 u7 v7 x7 Y7 27 ZA7 ZB7 ZC7
B8 C8 CD8 D8 E8 EF8 F8 =G8 G8 H8 JS8 J8 K8 M8 N8 P8 38 58 l-8 U8 V8 X8 Y8 28 ZA8 ZB8 zc8
49 B9 C9 CD9 D9 E9 EF9 F9 -G9 G9 H9 JS9 K9 M9 N9 P9 39 59 u9 x9 Y9 z9 zA9 ZB9 ZC9
410 BIO Cl0 CD10 DIO El0 EFIO FlO -GlO G10 HI0 JSIO KIO Ml0 NIO PlO 310 510 UlO x10 YlO ZlO ZAlO ZBlO ZClO
ill Bll Cl1 Dll Hll JSII Nil Zll ZAll ZBll ZCll
412 B12 Cl2 012 H12 JS12
413 B13 Cl3 D13 H13 JS13
HI4 JS14
H15 JS15
H16 JS16
H17 JS17
H18 JS18
4 5 6
t 7
t 8 9 iii 13 14 15 16
Tables
Figure 2 - Synoptic representation of tolerance classes for holes for basic sizes less than or equal to 500 m m
HI
H2
H3
H4
H5
D6 E6 F6 G6 H6 JS6 K6 M6 N6 P6 R6 S6 T6 U6
D7 E7 F7 G7 H7 JS7 K7 M7 N7 P7 R7 s7 l-7 u7
08 ES F8 G8 H8 JS8 K8 M8 N8 P8 R8 S8 T8 U8
D9 E9 F9 H9 JS9 N9 P9
D-IO El0 HlO JSlO
Dll HI1 JSll
D12 H12 JS12
D13 HI3 JS13
H14 JS14
HI5 JS15
H16 JS16
HI7 JS17
H18 JS18
I
3
4 I 5 6 7 8 9 12 13
Tables
NOTE - The tolerance classes in the frame are given for experimental use.
Figure 3 - Synoptic representation of tolerance classes for holes for basic sizes
greater than 500 m m and less than or equal to 3 150 m m
5
IS0 286-2 : 1988 (El
hl jsl
h2 jQ
ef3 f3 fg3 93 h3 ja k3 m3 n3 P3 r3 s3
ef4 f4 fg4 94 h4 M k4 m4 n4 p4 r4 s4
cd5 d5 e5 ef5 f5 fg5 95 h5 js5 j5 k5 m5 n5 P5 r5 s5 t5 u5 u5 x5
cd6 d6 e6 ef6 f6 fg6 96 h6 js6 j6 k6 m6 n6 P6 r6 s6 t6 u6 ~6x6 y6 z6 za6
cd7 d7 e7 ef7 f7 fg7 co h7 js7 j7 k7 m7 n7 P7 r7 s7 t7 u7 u7 x7 y7 z7 za7 zb7 zc7
c8 cd8 d8 e8 ef8 f8 fg8 g8 h8 W j8 k8 m8 n8 p8 r8 s8 t8 u8 u8 x8 y8 z8 za8 zb8 zc8
a9 b9 c9 cd9 d9 e9 ef9 f9 fg9 99 h9 id k9 m9 n9 P9 f-9 s9 u9 x9 y9 z9 za9 zb9 zc9
a10 b10 cl0 cdl0 d10 e10 efl0 f10 fgl(3 g10 h10 jsl0 kl0 PI0 r-10 SlO x10 y10 z10 zal0 zbl0 zcl0
all bll cl1 dll hll jsl 1 kll zll zall zbll zcll
al2 b12 cl2 d12 h12 js12 k12
al3 b13 d13 h13 js13 k13
h14 js14
h15 js15
h16 js16
h17 js17
h18 js18
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Tables
Figure 4 - Synoptic representation of tolerance classes for shafts for basic sizes less than or equal to 500 m m
hl jsl
h2 js2
h3 js3
h4 W
h5 js5 J
e6 f6 96 h6 js6 k6 m6 n6 P6 t-6 s6 t6 u6
d7 e7 f7 97 h7 js7 k7 m7 n7 P7 r7 s7 t7 u7
d8 e8 f8 g8 h8 js8 k8 ~8 r8 s8 u8
d9 e9 f9 h9 js9 k9
d10 e10 h10 jsl0 k10
dll hll jsll kll
h12 js12 k12
h13 js13 k13
h14 js14
h15 js15
h'l6 js16
h17 js17
h18 js18
18 19 20 21 22 23 24 25 26 27 28 29
Tables
NOTE - The tolerance classes in the frame are given for experimental use.
Figure 5 - Synoptic representation of tolerance classes for shafts for basic sizes
greater than 500 m m and less than or equal to 3 150 m m
IS0 286-2 : 1988 (El
1 Values may be calculated, from the bases given in IS0 286-1, for fundamental deviations used for tolerance classes,
for which there is no entry in the tables, but for which the space has been left blank.
2 A small horizontal separation has been inserted in the tables, where appropriate, to distinguish between values for
basic sizes less than or equal to 500 m m and those greater than 500 mm, which have been derived from different bases.
7
IS0 286-2 : 1988 (E)
Basic
Above
size
mm
up to
and in- 9 IO
AZ)
11 12 13
T 8
I
9 10
B2)
1
11
1
12 13 8 9 10
C
11 12
1
eluding
- 32) + 295 + 310 + 330 + 370 + 410I +I54 +I65 + 180 + 200 + 240 + 280 +74 +85 +I00 +I20 + 160 +200
+ 270 + 270 + 270 + 270 + 270 I +I40 +I40 + 140 + 140 + 140 + 140 +60 +60 +60 +60 + 60 + 60
3 6 + 300 + 318 + 345 + 390 + 450 I +I58 +I70 + 188 + 215 + 260 + 320 + 88 +I00 +I18 +I45 + 190 +250
+ 270 + 270 + 270 + 270 + 270 I +I40 +I40 + 140 + 140 + 140 + 140 +70 +70 +70 + 70 + 70 + 70
6 10 + 316 + 338 + 370 + 430 + 500I +I72 +I86 + 208 + 240 + 300 + 370 +I02 +I16 +I38 +I70 + 230 +300
+ 280 + 280 + 280 + 280 + 280 I +I50 +I50 + 150 + 150 + 150 + 150 +80 +80 +80 +80+ 80 + 80
10 18 +333+360+400+ 470+ 560I 4-177 +I93 + 220 + 260 + 330 + 420 +I22 +I38 +I65 +205 + 275 + 365
+ 290 + 290 + 290 + 290 + 290 I +I50 +I50 + 150 + 150 + 150 + 150 +95 +95 +95 + 95 + 95 + 95
18 30 + 352 + 384 + 430 + 510 + 630 I +I93 +212 + 244 + 290 + 370 + 490 +I43 +I62 +I94 +240 + 320 +440
+300+300+300+300+300 +16o +I60 + 160 + 160 + 160 + 160 +I10 +I10 +I10 +I10 + 110 + 110
30 40 + 372 + 410 + 470 + 560 + 700 +209 +232 + 270 + 330 + 420 + 560 +I59 +I82 +220 +280 + 370 + 510
+ 310 + 310 + 310 + 310 + 310 +I70 +I70 + 170 + 170 + 170 + 170 +I20 +I20 +I20 +I20 + 120 + 120
40 50 + 382 + 420 + 480 + 570 + 710 +219 +242 + 280 + 340 + 430 + 570 +I69 +I92 +230 +290 + 380 + 520
+ 320 + 320 + 320 + 320 + 320 +I80 +I80 + 180 + 180 + 180 + 180 +I30 +I30 +I30 +I30 + 130 + 130
50 65 + 414 + 460 + 530 + 640 + 800 +236 +264 + 310 + 380 + 490 + 650 +I86 +214 +260 +330 + 440 +600
+340+340+340+340+340 +I90 +I90 + 190 + 190 + 190 + 190 +I40 +I40 +I40 +I40 + 140 + 140
65 80 + 434 + 480 + 550 + 660 + 820 +246 +274 + 320 + 390 + 500 + 660 +I96 +224 +270 +340 + 450 + 610
+360+360+360+360+360 +200 +200 + 200 + 200 + 200 + 200 +I50 +I50 +I50 +I50 + 150 + 150
80 100 + 467 + 520 + 600 + 730 + 920 +274 +307 + 360 + 440 + 570 + 760 +224 +257 +310 +390 + 520 + 710
+ 380 + 380 + 380 + 380 + 380 +220 +220 + 220 + 220 + 220 + 220 +I70 +I70 +I70 +I70 + 170 + 170
100 120 + 497 + 550 + 630 + 760 + 950 +294 +327 + 380 + 460 + 590 + 780 +234 +267 +320 +400 + 530 + 720
+ 410 + 410 + 410 + 410 + 410 +240 +240 + 240 + 240 + 240 + 240 +I80 +I80 +I80 +I80 + 180 + 180
120 140 + 560 + 620 + 710 + 860 +I090 +323 +360 + 420 + 510 + 660 + 890 +263 +300 +360 +450 + 600 + 830
+ 460 + 460 + 460 + 460 + 460 +260 +260 + 260 + 260 + 260 + 260 +200 +200 +200 +200 + 200 +200
140 160 + 620 + 680 + 770 + 920 +I150 +343 +380 + 440 + 530 + 680 + 910 +273 +310 +370 +460 + 610 +840
+ 520 + 520 + 520 + 520 + 520 +280 +280 + 280 + 280 + 280 + 280 +210 +210 +210 +210 + 210 + 210
160 180 + 680 + 740 + 830 + 980 +I210 +373 +410 + 470 + 560 + 710 + 940 +293 +330 +390 +480 + 630 +860
+ 580 + 580 + 580 + 580 + 580 +310 +310 + 310 + 310 + 310 + 310 +230 +230 +230 +230 + 230 + 230
180 200 + 775 + 845 + 950 +I120 +I380 +412 +455 + 525 + 630 + 800 +I060 +312 +355 +425 +530 + 700 +960
+ 660 + 660 + 660 + 660 + 660 +340 +340 + 340 + 340 + 340 + 340 +240 +240 +240 +240 + 240 + 240
200 225 + 855 + 925 +I030 +I200 +I460 +452 +495 + 565 + 670 + 840 +I 100 +332 +375 +445 +550 + 720 +980
+ 740 + 740 + 740 + 740 + 740 +380 +380 + 380 + 380 + 380 + 380 +260 +260 +260 +260 + 260 + 260
225 250 + 935 +I005 +I110 +I280 +I540 +492 +535 + 605 + 710 + 880 +I140 +352 +395 +465 +570 + 740 +I ooo
+ 820 + 820 + 820 + 820 + 820 +420 +420 + 420 + 420 + 420 + 420 +280 +280 +280 +280 + 280 + 280
250 280 +I050 +I130 +I240 +I440 +I730 +561 +610 + 690 + 800 +I000 +I 290 +381 +430 +510 +620 + 820 +I 110
+ 920 + 920 + 920 + 920 + 920 +480 +480 + 480 + 480 + 480 + 480 +300 +300 +300 +300 + 300 +300
280 315 +I180 +I260 +I370 +I 570 +I860 +621 +670 + 750 + 860 +I060 +I 350 +411 +460 +540 +650 + 850 +I 140
+I050 +I050 +I050 +I050 +I050 +540 +540 + 540 + 540 + 540 + 540 +330 +330 +330 +330 + 330 + 330
315 355 +I340 +I430 +I560 +I770 +2000 +689 +740 + 830 + 960 +I170 +I490 +449 +500 +590 +720 + 930 +I250
+I200 +I200 +I200 +I200 +I200 +600 +600+600+600+600 + 600 +360 +360 +360 +360 + 360 + 360
355 400 +I490 +I580 +1710 +I920 +2240 A-769 +820 + 910 +I040 +I250 +I570 +489 +540 +630 +760 + 970 + 1 290
+I350 +I350 +I350 +I350 +I350 +680 +680 + 680 + 680 + 680 + 680 +400 +400 +400 +400 + 400 +400
400 450 +I655 +I750 +I900 +2130 +2470 +857 +915 +I010 +I 160 +I390 +I730 +537 +595 +690 +840 +I070 +I410
+I500 +I500 +I500 +I500 +I500 +760 +760 + 760 + 760 + 760 -I- 760 +440 +440 +440 +440 + 440 +440
450 500 +I805 +I900 +2050 +2280 +2620 +937 +995 +I090 +I240 +I470 +I810 +577 +635 +730 +880 +I 110 +I450
+I650 +I650 +I650 +I650 +I650 +840+84Q+840+840+840 + 840 +480 +480 +480 +480 + 480 + 480
t f .
1) Fundamental deviations A, B and C are not provided for basic sizes greater than 500 mm.
2) Fundamental deviations A and B shall not be used for any standard tolerance in basic sizes less than or equal to 1 mm.
IS0 286-2 : 1988 (E)
+I70 +I85 +208 + 245 + 305 + 395 + 545 + 775 +I03 +I10 +I25 +I48 +I85 + 245
120 180 +I45 +I45 +I45 + 145 + 145 + 145 + 145 + 145 + 85 + 85 + 85 + 85 + 85 + 85
+I99 +216 +242 + 285 + 355 + 460 + 630 + 890 +I20 +I29 +I46 +I72 +215 + 285
180 250 +I70 +I70 +I70 + 170 + 170 + 170 + 170 + 170 +I00 +I00 +I00 +I00 +I00 + loo
+222 +242 +271 + 320 + 400 + 510 + 710 +I 000 +I33 +I42 +I62 + 191 +240 + 320
250 315 +I90 +I90 +I90 + 190 + 190 + 190 + 190 + 190 +I10 +I10 +I10 +I10 +I10 + 110
+246 +267 +299 + 350 + 440 + 570 + 780 +I 100 +I50 +I61 +I82 +214 +265 + 355
315 400 +210 +210 +210 + 210 + 210 + 210 + 210 + 210 +I25 +I25 +I25 +I25 +I25 + 125
+270 +293 +327 + 385 + 480 + 630 + 860 +I200 +I62 +I75 +I98 +232 +290 + 385
400 500 +230 +230 +230 + 230 + 230 + 230 + 230 + 230 +I35 +I35 +I35 +I35 +I35 + 135
+304 +330 +370 + 435 + 540 + 700 + 960 +I 360 +I89 +215 +255 +320 + 425
500 630 +260 +260 +260 + 260 + 260 + 260 + 260 + 260 +I45 +I45 +I45 +I45 + 145
+340 +370 +415 + 490 + 610 + 790 +I090 +I540 +210 +240 +285 +360 + 480
630 800 +290 +290 +290 + 290 + 290 + 290 + 290 + 290 +I60 +I60 +I60 +I60 + 160
+376 +410 +460 + 550 + 680 + 880 +I220 +I720 +226 +260 +310 +400 + 530
800 1 000 +320 +320 +320 + 320 + 320 + 320 + 320 + 320 +I70 +I70 +I70 +I70 + 170
+416 +455 +515 + 610 + 770 +I010 +I400 +2000 +261 +300 +360 +455 + 615
1 000 1 250 +350 +350 +350 + 350 + 350 + 350 + 350 + 350 +I95 +I95 +I95 +I95 + 195
+468 +515 +585 + 700 + 890 +I170 +I640 +2340 +298 +345 +415 +530 + 720
1 250 1 600 + 390 + 390 +390 + 390 + 390 + 390 + 390 + 390 +220 +220 +220 +220 + 220
+522 +!j80 +660 + 800 +I030 +I350 +I930 +2730 +332 +390 +470 +610 + 840
1 600 2 000 +430 +430 +430 + 430 + 430 + 430 + 430 + 430 +240 +240 +240 +240 + 240
+5!30 +655 +760 + 920 +I180 +I580 +2230 +3280 +370 +435 +540 +700 + 960
2 000 2 500 +480 +480 +480 + 480 + 480 + 480 + 480 + 480 +260 +260 +260 +260 + 260
+655 +730 +850 +I060 +I380 +I870 +2620 +3820 +425 +500 +620 +830 +I150
2 500 3 150 +520 +520 +520 + 520 + 520 + 520 + 520 + 520 +290 +290 +290 +290 + 290
1) The intermediate fundamental deviation CD is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental
deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.
9
IS0 286-2 : 1988 (El
Basic size
EF’) F
mm
up to
Above and in- 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
eluding
- 3 +I2 +I3 +I4 +I6 +20 +24 +35 +50 +8 +9 + 10 + 12 + 16 + 20 +31 +46
+I0 +I0 +I0 +I0 +I0 +I0 +I0 +I0 +6 +6 +6 +6 +6 +6 +6 +6
+16,5 +I8 +I9 +22 +26 +32 +44 +62 +12,5 +I4 +I5 +I8 +22 +28 +40 +58
3 6
+I4 +I4 +I4 +I4 +I4 +I4 +I4 +I4 +I0 +I0 +I0 + 10 + 10 + 10 + 10 + 10
+20,5 +22 +24 -1-27 +33 +40 +54 +76 +15,5 +I7 +I9 +22 + 28 +35 +49 + 71
6 10
+I8 +I8 +I8 +I8 +I8 +I8 +I8 +I8 +I3 +I3 +I3 + 13 + 13 + 13 + 13 + 13
10
IS0 286-2 : 1988 (El
Basic size
FG 1) G
mm
up to
Above and in- 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
eluding
+6 -1-7 -+8 +I0 +I4 +I8 +29 +44 + 4 +5 +6 +8 + 12 + 16 + 27 + 42
- 3
-f-4 +4 -I-4 +4 -I-4 +4 +4 -+4 +2 +2 +2 +2 +2 +2 +2 +2
3 6 + 8,5 +I0 +I1 +I4 +I8 +24 +36 +54 + 6,5 + 8 + 9 + 12 +I6 +22 +34 + 52
+6 +6 +6 +6 +6 +6 +6 +6 +4 d-4 -I4 4-4 4-4 4-4 +4 +4
6 lo +10,5 +I2 +I4 +I7 +23 +30 +44 +66 + 7,5 + 9 +I1 + 14 + 20 + 27 + 41 + 63
+8 +8 +8 +8 +8 +8 +8 +8 +5 +5 +5 +5 +5 +5 +5 +5
10 18 +9 +I1 +I4 + 17 -1-24 +33 +49 + 76
+6 +6 +6 +6 +6 +6 +6 +6
1) The intermediate fundamental deviation FG is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamen-
tal deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.
11
IS0 286-2 : 1988 E)
Basic size H
10 18 +I,2 + 2 + 3 + 5 + 8 + 11 + 18 -1-27 +43 + 70 + 110 +0,18 +0,27 +0,43 +0,7 + I,' + I,8 + 2,7
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
18 30 +1,5+2,5+4 +6 +9 + 13 +21 +33 + 52 + 84 + 130 +0,21 +0,33 +0,52 +0,84 + I,3 + 2,l + 3,3
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
30 50 +I,5 + 2,5 + 4 + 7 +I1 + 16 + 25 + 39 + 62 +I00 + 160 +0,25 +0,39 +0,62 +I + I,6 + 2,5 + 3,9
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
50
80 +; +; '0" +; +I; + 19 +30 +46 + 74 +I20 + 190 +0,3 +0,46 +0,74 +I,2 +I,9 +3 + 4,6
0 0 0 0 0 0 0 0 0 0 0 0 0
80 120 +2,5 + 4 + 6 +I0 +I5 +22 +35 +54 + 87 +I40 + 220 +0,35 + 0,54 +0,87 +I,4 + 2,2 + 3,5 + 5,4
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+3,5+5 +8 +I2 +I8 +25 +40 +63 +I00 +I60 + 250 +0,4 +0,63 +I +I,6 + 2,5 i- 4 + 6,3
120 180 o
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
180 250 +4,5 + 7 +I0 +I4 +20 +29 +46 + 72 +I15 +I85 + 290 +0,46 +0,72 +I,15 +I,85 + 2,9 + 4,6 + 7,2
o 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+I6 +23 +32 +52 +81 +I30 +210 + 320 +0,52 +0,81 +I,3 +2,1 + 3,2 + 5,2 + 8,'
250 315 +; + ; +I;
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
315 400 +7 + ; +I; +I8 +25 + 36 + 57 + 89 +I40 +230 + 360 +0,57 + 0,89 +I,4 +2,3 + 3,6 + 5,7 + 8,9
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
400 500 +," +I0 +I5 +20 -1-27 +40 +63 + 97 +I55 +250 + 400 +0,63 + 0,97 +I,55 +2,5 -I- 4 + 6,3 + 9,7
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2)
+ 9 +I1 +I6 +22 -132 +44 + 70 +I10 +I75 +280 + 440 +0,7 + I,' +I,75 +2,8 + 4,4 -I- 7 +I1
500 630
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+I0 +I3 +I8 +25 +36 +50 + 80 +I25 +200 +320 + 500 +0,8 +I,25 +2 +3,2 + 5 +8 +12,5
630 800
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
tll +I5 +21 +28 +40 +56 + 90 +I40 +230 +360 + 560 +0,9 +I,4 +2,3 +3,6 + 5,6 + 9 +I4
800 1 000
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
t13 +I8 +24 +33 +47 -I66 +I05 +I65 +260 +420 + 660 +I,05 +I,65 +2,6 +4,2 + 6,6 +10,5 +16,5
1 000 1 250
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
t15 +21 +29 +39 +55 + 78 +I25 +I95 +310 +500 + 780 +I,25 + I,95 +3,1 +5 + 7,8 +12,5 + 19,5
1 250 1 600
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
t18 +25 +35 +46 +65 + 92 +I50 +230 +370 +600 + 920 +I,5 +2,3 +3,7 +6 + 9,2 +I5 +23
1 600 2 000
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
----------------------
+22 +30 +41 +55 +78 +I10 +I75 +280 +440 +700 +I100 +I,75 +2,8 +4,4 -I-7 +I1 +17,5 +28
2 000 2 500
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+26 +36 +50 +68 +96 +I35 +210 +330 +540 +860 +I350 +2,1 +3,3 +5,4 +8,6 +13,5 +21 +33
2 500 3 150
0 0 0 01 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1) Tolerance grades IT14 to IT18 (incl.) shall not be used for basic sizes less than or equal to 1 mm.
2) The values given in the frame, for tolerance grades IT1 to IT5 (incl.), for basic sizes greater than 500 m m and less than or equal to 3 150 mm, are included
for experimental use.
12
IsO286-2:1988 (El
- - - - - - - - - - - - - -
0) V. E. 2 . 0 I\
Lo
- CD 3 3 3 in % 3 2 n IfI
d
%
d - Y 7
c
V-- d ti ti c-5 G d Ii5 us- od &- r Tr G-
7
F
+I +I +I +I +I +I +I +I +I +I +I +I +I +I +I +1 ;I +I +I
- - - - - - - - - - - - - - - - -
m
CD g Ql k9. %. If3. I? . m CD 3 - Ln 3 . w c E m
0’ d 6 7 7 - - N ci A 0.i c-6 ti * Lb cc5 b 00‘ Ci
-
+I +I +I +I fl +I +I +I +I +I +I +I +I +I +I +I + +I +I
- - - - - - - - - - - - - - - - -
m E %. 3 3 00 2 ? : . (v Lo cn U Lo 2
.
0‘ d d / c 0‘ 0‘ 0‘ T--
.
-
?
-
(4
-
00,
- cl cu’ 0.i
F
CT] c-5 us us i.z
3
+I +I +I I + +I +I +I +I +I +I +I +I +I +I +I +I +I T +I +I
- - - - - - - - - - - - - - - - - ?i
E
8 Lo
3 3 i % 2 Ln co b 00
0‘
6)
d
s
F
- .
-
3 .
-
T.
-
CD.
T-
-
ti
Ln
cu‘ (y:
m
ti
F
*
.-iif
0‘
+I
d 1
+ I
C
+
0‘
+I
0’
+I
0’
+I
0’
+I +I +I + +I +I +I +I +I +I + +I +I 5Q
- - -
- - - - - - - - - - - - - -
3
In
-
02I
r
lc
K % & % g Is
2
Lc g b K E CT si . 2 I\
5
. N,
Cb 0’ d 0‘ c C 0‘ 0‘ 0‘ - v- V r c\I cu’
0‘
+I + I
C
+
0‘
+I +I
0’
+I +I +I + + +I +I +I +I + +I + +I +I -E
u3
- - - - - - - - - - - - - - - - -
E
6 8
F
7
3
r
3
?
i%
F 3 Ri
In
F; %
5
3 g tfE 3
g 2
cn
Lc
r
.-t
0’ 0‘ Ci C 0‘ d 0‘ d 0‘ c C 0‘ 0’ d d C 0‘ r
T
-
3
F- i??
m
+I +I +I + +I +I +I +I +I + + +I +I +I +I + +I t fl +I
- - - - - - - - - - - - - - - - -
u: )
8 Ki m f;r!
m
3 g
E-
c- - 7 - 2 % Fj % d- 8 P 00 s
8
0‘
f ;
Ci
F
C d d d d
. c\1
0‘ c C
3
0‘ 0‘ 6 d C 0‘ C d 7 z-
+I
-
+I
-
+ I
-
+
-
+I
-
+I
-
+I
-
+I +I +
-
+
-
+I
-
+I
-
+I
-
+I
-
+
-
+I t
- -
+I
-
cv)
0
Lo.
) 0 , 3
? k
+I
3
+ I
Y
+
3
+I
8
+t
2
+I
F
F-
+I I
R
-
+I
3
I-
t
5
r
t
8
-
+I
8
N
+I
8
+I
t?
4
+
g
+
3
+I
3
t
i3
+I
K
10
+I c
40
- - - - - - -
Lo.
- - - - - - - - - - &
, Lo E
= m+ ? 0
R ’3 R % g 55 53 I8 % 3 - % 3 23 5: 3 5: 5
8 NQ ? - - Kl cv 0 9
+I +I +I +I +I +I +I fl +I +I +I +I +I h G fl +I ; +I +i %
,’ II 11 n - - - - - - - - - - - - - - - - - a,
7 7
m. Lo Ln. n. u
: ,gSC .2 In co tj- , b- 6
- 7 z % & k I3 Ln 3 ? k 2 8 s Isi !2
.I z .E 7 ? a
w ‘5 > +I +I +I +I +I +I fl +I +I +I +I +I fl G +I +I tl +I
co aa - -
- - - - - - - - - - - - - -
‘f 73’73
Ln In in ILn. Ln Ln. Lo. Ia .
b 0) F ti us ai co n
F- - 7 c- 3 Ri ,z M $ ii ii 2 % 2 is 3
.I: -E
z- .-SE -
+I +I +I +I +I +I +I +I +I +I +I +I +I fl fl +I +I tl +I
E 5% - - - - - - - - - - -
- - - - -
2 ng
Ln Lo lo In Lo. In . m Lo. Lo.
I 5s Ln CD r; cn 0‘ ci- Ln r\‘
- - ? F E 8 8 3 z 3 3 d 2 9 k
c\ +I +I +I +I +I +I +I +I +I +I +I +I +I +I +I +I +I tl +I
Q) - - - - - - - - - - - - - - - -
9
Ln Ln m In Lo In
tff 0 d- d: ti cci co cn’ F ti & CD 00
- v - - R iY 3 3 3 3 3
+I +I +I +I +I +I +I ;I; +I +I +I +I +I +I +I +I +I tl +I
- - - - - - - - - - -- -- -- -- -- --
Ln in In In In In . Ln In I.0. In . n.
cl ci- m d- d lb- cb- PJ Q) 0 - ci- ce- CD Co
- 7 - - F 3 Ki Y 3
+I +I +I +I +I +I +I +I +I +I +I I +I +I G +I +I +I tl +I
- - - - - - - - - - - - - - - -
m Ln Lo m I.0 in .
(v cv c\j 0 <yi e I.0 CD I-- al , 0, 0 7 ni- ti cs
F 7 7 - 3 R
+I +I +I +I +I +I +I +1 +I +I I +I +I G +I +I +I tl +I
- - - - - - - - - - - - - - - -
1.n n In .
w 3 Ln Lo In Ln <
co m cv 6
V- - - c\1 c\1 c\i m e m CD, cs rQ- V - E
+I +I +I +I +I +I +I +I +I + I +I +I +I +I +I +I ;r; +I
- - - - - - - - - - - - - - - -
Lo m in n
E E %. Q In . m Ln Ln ti ti 0-l 0‘ Y.i In
0‘ d F 7 T- - cl CG ti * d In 7 7
+I +I +I +I +I +I +I +I +I + I +I +I +I +I +I +I h +I
- - - - - - - - - - - - - - - -
In m. In
In In a 2 E G 2 . R In d m cd K 51 -
0‘ d c d 0‘ - c- - 4 cv:I ti e -
+I +I + +I +I +I +I +I +I + I +I +I +I +I +I +I + +I
- - - - - - - - - - -- - -- - --
CD 0 Cm lc 1
T-- F E 53 8 3 3 8 8
- z I 3 8 E E cv CD 3 If2
rl N
- - - - - - - -- - - - - - - - -
v) D 3 lo Is) 3 >
7 7 % 3 3 3 3 3
N ;5 3 2 % 3 u ; 3
N
- - - - - - - - - - -
13
IS0 286-2:1988 (El
- 3 +2 -l-4 +6 0 0 0 0 0 0 0 0
-4 -6 -8 -2 -3 -4 - 6 - 10 - 14 -25 -40
3
I
6 ‘Zl -311 yl I-;.,1 ‘:::l -;l:;l’;l:l,“l I
6 IO ‘Z / ‘; j 1;; 1 0
-2,5
+0,5
-3,5
+ 1
-5
+
-
2
7
+ 5
- 10
+ 6
- 16
10
I
18 : ; / :I: / ‘:; 1 -3
0 +I
-4
+2
-6
+
-
2
9
+ 6
- 12
+ 8
- 19
18 30 : ; 1 “; / ‘:: 1 -0,5
-4,5 -6
0 +I
-8
+ 2
- 11
+ 6
- 15
+ IO
- 23
+I0 +I4 +24 -0,5 +I +2 + 3 + 7 + 12
30 50
-6 -11 -15 -4,5 -6 -9 - 13 - 18 - 27
+I3 +I8 +28 +3 + 4 + 9 + 14
50 80
-6 -12 -18 -10 - 15 - 21 - 32
+I6 +22 +34 +2 + 4 + 10 + 16
80 120
-6 -13 -20 -13 - 18 - 25 -38
+I8 +26 +41
120 180
-7 -14 -22 / / 'l;/',:jz~::l I
-G--p +22
-7
+30
-16
+47
-25 I I 'Ii I :2: I:: I ZG I I
+25 +36 +55
250 315
-7 -16 -26 I I '2~I'2;lzlz;I I
500 630 0 0 0
-44 - 70 -110
630 800 0 0 0
- 50 - 80 -125
800 1 000 0 0 0
- 56 - 90 -140
1 000 1 250 0 0 0
- 66 -105 -165
1 250 1 600 0 0 0
- 78 -125 -195
1 600 2 000 0 0 0
- 92 -150 -230
2 000 2 500 0 0 0
-110 -175 -280
2 500 3 150 0 0 0
-135 -210 -330
_. -. .- _-- -
1) I olerance classes JY, JIO, etc. are symmetrical about the zero line. For these values, see JS9, JSIO, etc,
2) Deviations for K in tolerance grades above IT8 are not defined for basic sizes greater than 3 mm.
14
ISO286-2:1988(E)
(I Basic
mm
size
M
Upper limit deviation
Lower limit deviation
= ES
= EI
Deviations in micrometres
up to
Above and in-
cluding
-2 -2 -2 -2-2-2 -2 -2-4 -4 -4-4-4-4-4-4-4
- 3’)
-4 -5 -6 - 8 - I2 - I6 -27 -42 -6 -7 -8 - IO - 14 - 18 -29 -44 -64
-3 - 2,5 - 3 - 1 0+2-4 - 4 -7 -6,5 -7 - 5 - 4 - 2 0 0 0
3 6
- 5,5 - 6,5 - 8 - 9 - 12 - 16 -34 - 52 - 9,5 -lo,5 -12 - 13 - 16 - 20 - 30 - 48 - 75
-5 - 4,5 - 4 - 3 O+l-6 - 6 -9 -8,5 -8 - 7 - 4 - 3 0 0 0
6 IO
- 7,5 - 8,5 -10 - 12 - 15 - 21 -42 - 64 -11,5 -12,5 -14 - 16 - 19 - 25 - 36 - 58 - 90
-6 -5 -4 - 4 0+2-7 - 7 -11 -10 -9 -9-5-3 0 0 0
10 18
-9 -10 -12 - I5 - 18 - 25 -50 - 77 -14 -15 -17 -20 -23 -30 -43 -70 -110
-6,5 -6 -5 - 4 0+4-8 - 8 -13,5 -13 -12 -II -7 - 3 0 0 C
18 30
-10,5 -12 -14 - 17 - 21 - 29 -60 - 92 -17,5 -19 -21 -24 -28 -36 -52 -84 -130
-7,5 -6 -5 - 4 0+5 -9 - 9 -15,5 -14 -13 -12 - 8 - 3 0 0 C
30 50
-11,5 -13 -16 - 20 - 25 - 34 -71 -109 -19,5 -21 -24 -28 -33 - 42 - 62 -100 -160
-6 - 5 0 + 5 -15 -14 - 9 - 4 0 0 0
50 80
-19 - 24 - 30 - 41 -28 - 33 - 39 - 50 - 74 -120 -190
-8 -6 0 +6 -18 - 16 -10 - 4 0 0 0
80 120
-23 - 28 - 35 - 48 -33 - 38 - 45 - 58 - 87 -140 -220
-9 - 8 0+8 -21 - 20 -12 - 4 0 0 0
120 180
-27 - 33 - 40 - 55 -39 - 45 - 52 - 67 -100 -160 -250
-11 - 8: 0 + 9 -25 -22 -14 - 5 0 0 0
180 250
-31 - 37 - 46 - 63 -45 ' - 51 - 60 - 77 -115 -185 -290
-13 - 9 0 + 9 -27 -25 -14 - 5 0 0 C
250 315
-36 - 41 - 52 - 72 -50 -57 -66 - 86 -130 -210 -32C
-14 - 10 0 +ll -30 -26 -16 - 5 0 0 C
315 400
-39 -46 -57 -78 -55 - 62 - 73 - 94 -140 -230 -36C
I I -16
-43 --50 10 -63 0 -86
+I1 -60
-33 - 67
-27 - 80
171-6 -103 -155 0 -250 0 -4OCC
400 500
I
2 000 2500 -68 -68 -68 -110 -110 -110 -110
-178 -243 -348 -220 -285 -390 -550
2 500 3 150 - 76 - 76 - 76 -135 -135 -135 -135
-211 -286 -406 I -270 -345 -465 -675
I) Tolerance classes N9, NIO and Nil shall not be used for basic sizes less than or equal to 1 mm.
15
IS0 286-2 : 1988 (El
Basic size
P
mm
up to
Above andin- 3 4 5 6 7 8 9 10
eluding
-6 -6 -6 -6 -6 -6 -6 -6
- 3
-8 -9 -10 - 12 - 16 - 20 - 31 - 46
3 6 -11 -IO,5 -11 -9 -8 - 12 - 12 - 12
-13,5 -14,5 -16 - 17 - 20 - 30 -42 -60
6 IO -14 -13,5 -13 -12 -9 - 15 - 15 - 15
-16,5 -17,5 -19 - 21 - 24 - 37 - 51 - 73
IO 18 -17 -16 -15 - 15 - 11 - 18 - 18 - 18
-20 -21 -23 - 26 - 29 - 45 -61 -88
18 30 -20,5 -20 -19 - 18 -14 -22 -22 -22
-24,5 -26 -28 - 31 - 35 - 55 - 74 -106
50 80 -27 - 26 - 21 - 32 - 32
-40 - 45 - 51 - 78 -106
80 120 -32 - 30 - 24 - 37 - 37
-47 -52 -59 - 91 -124
500 630 - 78 - 78 - 78 - 78
-122 -148 -188 -253
630 800 -88 -88 -88 -88
-138 -168 -213 -288
800 1 000 -100 -100 -100 -100
-156 -190 -240 -330
1000 1 250 -120 -120 -120 -120
-186 -225 -285 -380
1250 1 600 -140 -140 -140 -140
-218 -265 -335 -450
1 600 2 000 -170 -170 -170 -170
-262 -320 -400 -540
2 000 2 500 -195 -195 -195 -195
-305 -370 -475 -635
2 500 3 150 -240 -240 -240 -240
-375 -450 -570 -780
16
IS0 286-2 : 1988 (E)
17
ISO286=2:1988(E)
Basic size
I S
mm I
up to
Above andin- 3 4 5 6 7 8 9 "10
eluding
-14 -14 - 14 - 14 - 14 - 14 - 14 - 14
- 3
-16 -17 - 18 - 20 - 24 - 28 - 39 4 - 54
3 6 -18 -17,5 - 18 - 16 - 15 - 19 - 19 8 - 19
-20,5 -21,5 - 23 - 24 - 27 - 37 - 49 - 67
6 10 -22 -21,5 - 21 - 20 - 17 - 23 - 23 - 23
-24,5 -25,5 - 27 - 29 - 32 -45, -59 - 81
30 50 -41,5 -40 -39 -38 -34 -43 -43 -43 900 1 000 - 470 - 470 - 470
-45,5 -47 -50 -54 -59 -82 -105 -143 - 526 - 560 - 610
140 160 -94 -93 -85 -100 -100 1800 2 000 - 920 - 920 - 920
-112 -118 -125 -163 -200 -1012 -1 070 -1150
160 180 -102 - 101 - 93 -108 -108 2000 2 240 -1 ooo -1 ooo -loo0
-120 -126 -133 -171 -208 -1 110 -1 175 -1280
180 200 -116 -113 -105 -122 -122 2 240 2500 -1100 -1 loo -1100
-136 -142 -151 -194 -237 -1210 -1 275 -1380
I I I I I I I I ! I
I
200/ 2251 / 1 1;: 1 1:: / 1;: / 1;;;1 1;:; j 1 2500 2800 -1250
-1385
-1 250
-1460
-1250
-1580
225 250 -134 -131 -123 -140 -140 2800 3 150 -1400 -1400 -1400
-154 -160 -169 -212 -255 -1535 -1 610 -1730
250 280 -151 -149 -138 -158 -158
-174 -181 -190 -239 -288
18
IS0 286-2 : 1988 (E)
Above
up to
and in-
eluding
5 6 7 8 5
-18 -
6
18 -
7
18 -
8
18 -
9
18 -
10
18
_ lcTd~g1617181617
Above
- 3
-22 - 24 -
500 t 560 I 400-400-400-600-600-600
4.44 - 470 - 510 - 644 - 670 - 710 I
28 - 32 - 43 - 58 I
I
3 6 -22 - 20 - 19 - 23 - 23 - 23 630 - 450 - 450 -450-660-660-660
560
-27 - 28 - 31 - 41 - 53 - 71 - 494 - 520 - 560 - 704 - 730 - 770
l-44 -43 -39-48-56-55-51-60-60-60 I120 - 780 - 780 - 780 -1150 -1150 -1150
30 40 1 000 -
-55 - 59 - 64 - 87 -67 - 71 - 76 - 99 -122 -160 _ f#j 885 - 945 -1216 -1255 -1315
40 5o I;I&o-g3 45 -54 -66 -65 -61 -70 -70 -70 I 120 1 250 I 840 - 840 - 840 -1300 -1300 -1300
-77 -81 - 86 -109 -132 -170 906 - 945 -1005 -1366 -1405 -1465
I
50 65 -60 -55 -66 - 81 - 76 - 87 - 87 - 87 - acm - am - 960 -1450 -1450 -1450
1250 ( 1400 I-,;;1 -1
I - I "VW , - lfmi
. w-w , - '155
- 79 - 85 -112 -100 -106 -133 -161 -207 -1528 -1575 -1645
100 120 -97 -91 -104 -137 -131 -144 -144 -144 1800 2000 -1350 -1350 -1350 -2000 -2000 -2000
-119 -126 -158 -159 -166 -198 -231 -284 -1442 -1500 -1580 -2092 -"FfI
L I- I -3mf.I
c L”” ,
120 140 I -115 -107 -122 -163 -155 -170 -170 -170 -1500 -1500 -1500 -2300 -2300 -2300
2000 2 240
-140 -147 -185 -188 -195 -233 -270 -330 -1 610 -1675 -1780 -2410 -2475 -2580
140 160 -127 -119 -134 -183 -175 -190 -190 -190 -1650 -1650 -1650 -2500 -2500 -2500
2 240 2500
-152 -159 -197 -208 -215 -253 -290 -350 -1760 -1 825 -1 930 -2610 -2675 -2780
-1900 -1900 -1900 -2900 -2900 -2900
2500 2800
160 I80 1 -2035 -2110 -2230 -3035 -3110 -3230
--- -157 -149 -166 -227 -219 -236 -236 -236 -2100 -2100 -2100 -3200 -3200 -3200
180 200 2800 3 150
-186 -195 -238 -256 -265 -308 -351 -421 -2235 -2310 -2430 -3335 -3410 -3530
3113
IC ‘3tt -257 -247 -268 - 379 -369 -390 -390 -390
a;13
-293 -304 -357 -415 -426 -479 -530 -6X
355 400 -283 -273 -294 -424 -414 -435 -435 -4.35
-319 -330 -383 -460 -471 -524 -575 -665
400 450 -317 -307 -330 -477 -467 -490 -490 -49c
-357 -370 -427 -517 -530 -587 -645 -74c
4
‘b50 500 -347 -337 -360
-387 -400 -457
1) Tolerance classes T5 to T8 (incl.) have not been tabulated for basic sizes less than or equal to 24 mm. It is recommended that tolerance classes U5 to U8
(incl.) be used instead. However, if tolerance classes T5 to T8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-l.
19
ISO286=2:1988(E)
Basic size
V2) X Y3)
mm
1 Upto I I I I 1 I
Above andin- 5 6 7 8 5 6 7 8 9 10 6 7 8 9 10
eluding
- 3 - 20 - 20 - 20 - 20 -20 -20
- 24 - 26 -30 -34 -45 -60
3 6 - 27 - 25 - 24 - 28 - 28 - 28
-32 -33 -36 -46 -58 - 76
6 10 - 32 - 31 -28 -34 -34 -34
-38 -40 -43 -56 - 70 - 92
10 14 - 37 -37 -33 -40 -40 -40
-45 -48 - 51 -67 -83 -110
14 I8 -36 -36 - 32 - 39 - 42 -42 -38 -45 -45 - 45
-4 -47 -50 -66 -50 -53 -56 -72 -88 -115
18 24 1: 1: 1: - 47 -51 -50 -46 -54 -54 -54 - 59 - 55 - 63 -63 -63
-80 -60 -63 - 67 - 87 -106 -138 - 72 - 76 - 96 -115 -147
24 30 -52 - 51 - 47 - 55 -61 -60 -56 -64 -64 -64 - 71 - 67 - 75 - 75 - 75
-61 -64 -68 -88 - 70 -73 -77 - 97 -116 -148 - 84 - 88 - 108 -127 -159
30 40 -64 -63 -59 -68 - 76 - 75 -71 -80 -80 -80 - 89 - 85 - 94 -94 -94
-75 -79 -84 -107 - 87 -91 -96 -119 -142 -180 - 105 - 110 - 133 -156 -194
40 50 1: - 76 - 72 - 81 - 93 -92 -88 - 97 - 97 - 97 - 109 - 105 - 114 -114 -114
- 92 - 97 -120 -104 -108 -113 -136 -159 -197 - 125 - 130 - 153 -176 -214
50 65 -96 - 91 -102 -116 -111 -122 -122 - 138 - 133 - 144
-115 -121 -148 -135 -141 -168 -196 - 157 - 163 - 190
65 80 -114 -109 -120 -140 -135 -146 -146 - 168 - 163 - 174
-133 -139 -166 -159 -165 -192 -220 - 187 - 193 - 220
80 100 -139 -133 -146 -171 -165 -178 -178 - 207 - 201 - 214
-161 -168 -200 -193 -200 -232 -265 - 229 - 236 - 268
100 120 -165 -159 -172 -203 -197 -210 -210 - 247 - 241 - 254
-187 -194 -226 -225 -232 -264 - 297 - 269 - 276 - 308
120 140 -195 -187 -202 -241 -233 -248 -248 - 293 - 285 - 300
-220 -227 -265 -266 -273 -311 -348 - 318 - 325 - 363
140 160 -221 -213 -228 -273 -265 -280 -280 -333 - 325 - 340
-246 -253 -291 -298 -305 -343 -380 - 358 - 365 - 403
160 180 -245 -237 -252 -303 - 295 -310 -310 - 373 - 365 - 380
-270 -277 -315 -328 -335 -373 -410 - 398 -405 -443
180 200 -275 -267 -284 -341 -333 -350 -350 - 416 - 408 - 425
-304 -313 -356 -370 - 379 -422 -465 - 445 - 454 - 497
200 225 -301 - 293 -310 -376 -368 -385 -385 - 461 - 453 - 470
-330 -339 -382 -405 -414 -457 -500 -490 - 499 - 542
225 250 -331 -323 -340 -416 -408 -425 -425 - 511 - 503 - 520
-360 -369 -412 -445 -454 -497 -540 -540 - 549 - 592
250 280 -376 -365 -385 -466 -455 -475 -475 -571 -560 -580
-408 -417 -466 -498 -507 -556 -605 - 603 - 612 - 661
280 I 315 -416 -405 -425 -516 -505 -525 -525 - Ml - 630 - 650
-448 -457 -506 -548 -557 -606 -655 - 673 - 682 - 731
315 355 -464 -454 -475 -579 -569 -590 -590 - 719 - 709 - 730
-500 -511 -564 -615 -626 - 679 -730 - 755 - 766 - 819
355 400 -519 -509 -530 -649 -639 -660 -660 - 809 - 799 - 820
-555 -566 -619 -685 -696 -749 -800 -845 -856 - 909
400 450 -582 -572 -595 -727 -717 -740 -740 - 907 - 897 - 920
-622 -635 - 692 -767 -780 -837 -895 - 947 - 960 -1017
450 500 -647 -637 -660 -807 - 797 -820 -820 - 987 - 977 -1 ooo
-687 -700 -757 -847 -860 -917 - 975 -1 027 -1040 -1097
4
1) Fundamental deviations V, X and Y are not provided for basic sizes greater than 500 mm.
2) Tolerance classes V5 to V8 (incl.) have not been tabulated for basic sizes less than or equal to 14 mm. It is recommended that tolerance classes X5
to X8 (incl.) be used instead. However, if tolerance classes V5 to V8 (incl.) are especially required, they may be calculated from the bases given in
IS0 286-l.
3) Tolerance classes Y6 to YIO (incl.) have not been tabulated for basic sizes less than or equal to 18 mm. It is recommended that tolerance classes
Z6 to ZIO (incl.) be used instead. However, if tolerance classes Y6 to YIO (incl.) are especially required, they may be calculated from the bases given in
IS0 286-l.
IS0 286-2 : 1988 (El
Basic size
z ZA
mm
up to
Above and in- 6 7 8 9 10 11 6 7 8 9 10 11
eluding
- 3 - 26 - 26 - 26 - 26 - 26 - 26 - 32 - 32 - 32 - 32 - 32 - 32
-32 - 36 - 40 - 51 - 66 - 86 -38 - 42 - 46 - 57 - 72 - 92
3 6 - 32 - 31 - 35 - 35 - 35 - 35 - 39 - 38 - 42 - 42 - 42 - 42
-40 -43 -53 -65 -83 - 110 -47 - 50 - 60 - 72 - 90 - 117
6 1o --z - ;; - 2 - ; -2 :,; Iz - g - ;; - ; - 52 - 52
- - - - - - - 110 - 142
10 I4 -47 -43 -50 -50 -50 -50 -61 -57 -64 -64 -&I -64
-58 - 61 - 77 - 93 - 120 - 160 - 72 - 75 - 91 - 107 - 134 - 174
14 I8 -57 -53 -60 -60 -60 -60 -74 -70 -77 -77 -77 -77
-68 - 71 - 87 - 103 - 130 - 170 -85 - 88 - 104 - 120 - 147 - 187
I) Fundamental deviations Z and ZA are not provided for basic sizes greater than 500 mm.
21
IS0 286-2 : 1988 (El
Basic size
ZB zc
mm
4bove and tn 7 8 9 10 11
IE:,“, I 7 I * I g I I0 I ”
I
- 60 I - 60 I - 60 I - 60 I - 60
- 3 -2
- -z
- -g
- --2 - 70 - 74 - 85 - 100 - 120
- 76 -80 --El0 -80 -80
3 6 -;
- -;- -i- -i- 1,:
- 88 -98 - 110 - 128 - 155
- 91 - 97 - 97 - g-7 - 97
6 10 -- ;; -- ; I ,g 1 ,;; I ,;;
- 106 - 119 - 133 - 155 - 187
- 123 - 130 - 130 - 130 - 130
10 I4 1 1; z 1; 1 1; I 1; 1 2: - 141 - 157 - 173 - 200 - 240
14 18 - 101 - 108 - 108 - 108 - 108 - 143 - 150 - 150 - 150 - 150
- 119 - 135 - 151 - 178 - 218 - 161 - 177 - 193 - 220 - 260
18 24 - 128 - 136 - 136 - 136 - 136 - 180 - 188 - 188 - 188 - 188
- 149 - 169 - 188 - 220 - 266 - 201 - 221 - 240 - 272 - 318
24 30 - 152 - 160 - 160 - 160 - 160 - 210 - 218 - 218 - 218 - 218
- 173 - 193 - 212 - 244 - 290 - 231 - 251 - 270 - 302 -348
30 40 - 191 - 200 - 200 - 200 - 200 - 265 - 274 - 274 - 274 - 274
- 216 - 239 - 262 - 300 - 360 - 290 - 313 - 336 - 374 -434
40 50 - 233 - 242 - 242 - 242 - 242 - 316 - 325 - 325 - 325 - 325
- 258 - 281 - 304 - 342 - 402 - 341 - 364 - 387 - 425 - 485
50 65 - 289 - 300 - 300 - 300 - 300 - 394 - 405 - 405 - 405 - 405
- 319 -346 - 374 - 420 - 490 - 424 - 451 - 479 - 525 - 595
65 8o IFg - 360 - 360 - 360 - 360 - 469 -480 - 480 -480 -480
-4.06 -4.34 - 480 - 550 - 499 - 526 - 554 - 600 - 670
80 100 - 432 - 445 - 445 - 445 - 445 - 572 -585 - 585 -585 - 585
- 467 -499 - 532 - 585 - 665 - 607 -639 - 672 - 725 - 805
100 120 - 512 - 525 - 525 - 525 - 525 - 677 -690 - 690 - 690 -690
- 547 - 579 - 612 - 665 - 745 - 712 - 744 -n - 830 - 910
120 140 - 605 - 620 - 620 - 620 - 620 - 785 -800 -800 - 800 -800
- 645 -683 - 720 - 780 - 870 - 825 - 863 -900 -960 -1050
140 160 -685 - 700 - 700 - 700 - 700 - 885 -900 -900 - 900 - 900
- 725 - 763 -800 -860 - 950 - 925 -963 -1 ooo -1060 -1 150
160 180 - 765 - 780 - 780 - 780 - 780 - 985 -1 ooo -1 ooo -1 ooo -1 ooo
- 805 -843 -880 -940 -1 030 -1 025 -1063 -1100 -1 160 -1 250
180 - 880 - 880 - 880 -880 -1133 -1150 -1150 -1150 -1150
- 952 - 995 -1065 -1170 -1 179 -1222 -1 265 -1335 -1440
-943 -960 -960 -960 - 960 -1 233 -1250 -1250 -1250 -1250
200 225
-989 -1032 -1 075 -1145 -1250 - 1 279 -1322 -1 365 -1435 -1540
-1033 -1050 -1050 -1050 -1050 -1333 -1350 -1350 -1350 -1350
225 250
- 1 079 -1122 -1165 -1 235 -1340 - 1 379 -1422 -1465 -1535 -1640
-1180 -1200 -1200 -1200 -1200 -1530 -1550 -1550 -1550 -1550
250 280
-1 232 -1281 -1330 -1410 -1 520 -1582 -1631 -1680 -1 760 -1 870
-1280 -1300 -1300 -1300 -1300 -1680 -1700 -1700 -1 700 -1700
280 315
-1332 -1381 -1430 -1510 -1 620 -1 732 -1781 -1830 -1 910 -2020
- 1 479 -1500 -1500 -1500 -1500 - 1 879 -1900 -1900 -1900 -1900
315 355
-1536 -1589 -1640 -1 730 -1860 - 1 936 -1989 -2040 -2130 -2260
- 1 629 -1 650 -1650 -1650 -1650 -2079 -2100 -2100 -2100 -2100
355 400
-1686 - 1 739 -1790 -1880 -2010 -2136 -2189 -2240 -2330 -2460
-1827 -1850 -1850 -1850 -1850 -2377 -2400 -2400 -2400 -2400
400 450
-1890 -1947 -2005 -2100 -2250 -2440 -2497 -2555 -2650 -2800
-2077 -2100 -2100 -2100 -2100 -2577 -2600 -2600 -2600 -2600
450 500
1 -2140 -2197 -2255 -2350 -2500 -2640 -2 697 -2755 -2850 -3000
I) Fundamental deviations ZB and ZC are not provided for basic sizes greater than 500 mm.
22
IS0 286-2 : 1988 (El
Basic size
I
mm
up to
4bove and in- 9 10 11 12 13 8 9 IO 11 12 13 8 9 IO 11 12
eluding
- 270 - 270 - 270 - 270 - 270 -140 -140 - 140 - 140 - 140 -140 -60 -60 -60 -60 - 60
- 32)
- 295 - 310 - 330 - 370 - 410 -1% -165 - 180 - 200 - 240 - 280 - 74 - 85 -100 -120 - 160
3 6 - 270 - 270 - 270 - 270 - 270 -140 -140 - 140 - 140 - 140 - 140 - 70 - 70 - 70 - 70 - 70
- 300 - 318 -345 -390 - 450 -158 -170 - 188 - 215 - 260 - 320 - 88 -100 -118 -145 - 190
6 10 - 280 - 280 - 280 - 280 - 280 -1501~1501- WI- ltil- 15Ol- 1501~801-801~80/-801- EHI
- 316 - 338 - 370 - 430 - 500 -172 -186 - 208 -240 -300 - 370 -102 -116 -138 -170 - 230
I
- -150 -150 - 150 - 150 - 150 - 150 - 95 - 95 - 95 - 95 - 95
10 18 -333290 1;; 1: 1:; I2G
-177 -193 - 220 - 260 - 330 - 420 -122 -138 -165 -205 - 275
18 30 - 300 - 300 - 300 - 300 - 300 -160 -160 - 160 - 160 - 160 - 160 -110 -110 -110 -110 - 110
- 352 - 384 - 430 - 510 - 630 -193 -212 - 244 - 290 - 370 - 490 -143 -162 -194 -240 - 320
30 40 - 310 - 310 - 310 - 310 - 310 -170 -170 - 170 - 170 - 170 - 170 -120 -120 -120 -120 - 120
- 372 - 410 - 470 - 560 - 700 -209 -232 - 270 - 330 - 420 - 560 -159 -182 -220 -280 - 370
40 50 - 320 - 320 - 320 - 320 - 320 -180 -180 - 180 - 180 - 180 - 180 -130 -130 -130 -130 - 130
-382 - 420 - 480 - 570 - 710 -219 -242 -280 -340 - 430 - 570 -169 -192 -230 -290 - 380
-190 -190 - 190 - 190 - 190 - 190 -140 -140 -140 -140 - 140
50 65 Iy4I~I~:~I~ -236 -264 - 310 - 380 - 490 - 650 -186 -214 -260 -330 - 440
- -200 -200 - 200 - 200 - 200 - 200 -150 -150 -150 -150 - 150
65 80 _ 360
434 I z I ;; I z I ;y
-246 -274 - 320 - 390 - 500 - 660 -196 -224 -270 -340 - 450
-220 -220 - 220 - 220 - 220 - 220 -170 -170 -170 -170 - 170
80 loo IE 1;; I= 1;; I= -274 -307 -360 -440 - 570 - 760 -224 -257 -310 -390 - 520
I I
100 120 - 410 - 410 - 410 - 410 - 410 -240 -240 - 240 - 240 - 240 - 240 -180 -180 -180 -180 - 180
- 497 - 550 - 630 - 760 - 950 -294 -327 - 380 - 460 - 590 - 780 -234 -267 -320 -400 - 530
1) Fundamental deviations a, b and c are not provided for basic sizes greater than 500 mm.
2) Fundamental deviations a and b shall not be used for any standard tolerance grades in basic sizes less than or equal to 1 mm.
23
IS0 286-2 : 1988 (E)
Basic size
I cd’) d
mm
up to
Above and in- 5 6 7 8 9 10 5 6 7 8 9 10 11 12 13
eluding
-34 -34 -34 -34 -34 - 34 - 20 - 20 - 20 - 20 - 20 - 20 - 20 - 20 - 20
- 3
-38 -40 -44 -48 - 59 - 74 - 24 - 26 -30 -34 - 45 - 60 - 80 -120 - 160
3 6 -46 -4.6 -46 -46 -46 - 46 - 30 - 30 - 30 - 30 - 30 - 30 - 30 - 30 - 30
-51 -54 -58 -64 -76 -94 - 35 - 38 -42 -48 - 60 - 78 - 105 -150 - 210
6 '0 1: -56 1; 1; -56 -56 1; 1; 1; 1; -; - z - 40 -40 - 40
-65 -92 -114 - - - 130 -190 - 260
10 18 -50 -50 -50 -50 -50 -50 -50 -50 -50
-58 -61 -68 - 77 - 93 - 120 - 160 -230 - 320
18 30 - 65 - 65 - 65 - 65 - 65 - 65 - 65 - 65 - 65
- 74 - 78 - 86 - 98 - 117 - 149 - 195 -275 - 395
30 50 - 80 - 80 - 80 -80 - 80 - 80 - 80 -80 - 80
- 91 - 96 -105 -119 - 142 - 180 - 240 -330 - 470
50 80 -100 -100 -100 -100 - loo - loo - loo -100 - 100
-113 -119 -130 -146 - 174 - 220 - 290 -400 - 560
80 120 -120 -120 -120 -120 - 120 - 120 - 120 -120 - 120
-135 -142 -155 -174 - 207 -260 -340 -470 - 660
120 180 -145 -145 -145 -145 - 145 - 145 - 145 -145 - 145
-163 -170 -185 -208 - 245 - 305 - 395 -545 - 775
180 250 -170 -170 -170 -170 - 170 - 170 - 170 -170 - 170
-190 -199 -216 -242 - 285 - 355 - 460 -630 -890
250 315 -190 -190 -190 -190 - 190 - 190 - 190 -190 - 190
-213 -222 -242 -271 - 320 - 400 - 510 -710 -1000
315 400 -210 -210 -210 -210 - 210 - 210 - 210 -210 - 210
-235 -246 -267 - 299 -350 -440 - 570 -780 -1100
400 500 -230 -230 -230 -230 - 230 - 230 - 230 -230 - 230
-257 -270 - 293 -327 - 385 - 480 - 630 -860 -1200
’Ooo
1’250
1 1 1 1 / 1 I
I I
.
I I I I I I
I
I
I z I :;i I I E I I FitI
! I I I I
I,zl I
I
I
I
‘+00~ l l l 1 l I I
l /~~~I~~l3iI~~l~l~~l I
1 600 2000 -430 -430 - 430 - 430 - 430
-580 -660 - 800 -1 030 -1350
2ooo12500~l l l 1 l I I I~~/~~I~~~l~l~I~l~l I
2500 3 150 -520 -520 - 520 - 520 - 520
-730 -850 -1060 -1380 -1 870
1) The intermediate fundamental deviation cd is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental
deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.
24
IS0 286-2 : 1988 (E)
Basic size
e efl)
mm
I I I I I
up to
4bove and in-
eluding
5 6 7 8 9 10 3 4
I 5I 6I 7I * I 9 10
1) The intermediate fundamental deviation ef is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental
deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.
25
IS0 286-2 : 1988 (E)
Basic size
mm
ii-t% 3 4 5 6 7 8 9 10 3 4 5 6 7 8 9 10
eluding
-6 -6 -6 -6 -6 -6 -6 -6 -4 -4 -4 -4 -4 -4 -4 -4
- 3
-8 -9 -10 - 12 - 16 - 20 - 31 -46 -6 -7 -8 -10 -14 -18 -29 -44
3 6 -10 -10 -10 - 10 - 10 - 10 - 10 -10 -6 -6 -6 -6 -6 -6 -6 -6
-12,5 -14 -15 -18 -22 -28 -40 -58 - 8,5 -10 -11 -14 -18 -24 -36 -54
-
6 10 -13 -13 -13 - 13 - 13 - 13 - 13 -13 -8 -8 -8 -8 -8 -8 -8 -8
-15,5 -17 -19 -22 - 28 - 35 - 49 - 71 -IO,5 -12 -14 -17 -23 -30 -44 -66
10 18 -16 -16 -16 - 16 - 16 - 16 - 16 - 16
-19 -21 -24 -27 -34 -43 - 59 - 86
---
18 30 -20 -20 -20 - 20 - 20 - 20 - 20 - 20
-24 -26 -29 - 33 - 41 - 53 - 72 -104
30 50 -25 -25 -25 - 25 - 25 - 25 - 25 - 25
-29 -32 -36 -41 -50 -64 - 87 -125
50 80 -30 -30 - 30 - 30 - 30 - 30
-38 -43 -49 -60 - 76 -104
80 120 -36 -36 - 36 - 36 - 36 - 36
-46 -51 -58 - 71 - 90 -123
120 180 -43 -43 -43 -43 -43 -43
-55 -61 -68 -83 -106 -143
180 250 -50 -50 -50 -50 -50 -50
-64 -70 - 79 - 96 -122 -165
250 315 -56 -56 - 56 - 56 -56 -56
-72 -79 -88 -108 -137 -185
-.
315 400 -62 -62 - 62 - 62 - 62 - 62
-80 -87 - 98 -119 -151 -202
400 500 -68 -68 -68 -68 -68 -68
-88 -95 -108 -131 -165 -223
w3u - 76 - 76 - 76 - 76
3uu
-120 -146 -186 -251
630 800 - 80 - 80 - 80 - 80
-130 -160 -205 -280
800 1 000 - 86 - 86 - 86 - 86
-142 -176 -226 -316
1 000 1 250 - 98 - 98 - 98 - 98
-164 -203 -263 -358
1 250 1 600 -110 -110 --'IO -110
-188 -235 -305 -420
1 600 2 000 -120 -120 -120 -120
-212 -270 -350 -490
2 000 2 500 -130 -130 -130 -130
-240 -305 -410 -570
1) The intermediate fundamental deviation fg is provided primarily for fine mechanisms and horology. If tolerance classes involving this fundamental
deviation in other basic sizes are required, they may be calculated in accordance with IS0 286-l.
26
IS0 286-2 : 1988 (E)
Basic size
9
mm
up to
Shove and in- 3 4 5 6 7 8 9 10
eluding
-2 -2 -2 -2 -2 -2 -2 -2
- 3
-4 -5 -6 -8 - 12 - 16 -27 - 42
3 6 -4 -4 -4 -4 -4 -4 -4 -4
- 6,5 - 8 - 9 - 12 -16 -22 -34 - 52
6 10 -5 -5 -5 -5 -5 -5 -5 -5
- 7,5 - 9 -11 - 14 - 20 - 27 -41 -63
10 18 1; -6 -6 -6 -6 -6 -6 -6
-11 -14 - 17 -24 -33 -49 - 76
18 30 -7 -7 -7 -7 -7 -7 -7 -7
-11 -13 -16 - 20 -28 -40 -59 - 91
30 50 -9 -9 -9 -9 -9 -9 -9 -9
-13 -16 -20 -25 -34 -48 -71 -109
50 80 -10 -10 - 10 - 10 - 10
-18 -23 -29 -40 -56
80 120 -12 -12 - 12 - 12 - 12
-22 -27 - 34 -47 -66
120 180 -14 -14 - 14 - 14 - 14
-26 -32 -39 -54 -77
180 250 -15 -15 - 15 - 15 - 15
-29 -35 -44 - 61 - 87
250 315 -17 -17 - 17 - 17 - 17
-33 -40 - 49 -69 -98
315 400 -18 -18 - 18 - 18 - 18
-36 -43 -54 - 75 -107
400 500 -20 -20 - 20 - 20 - 20
-40 -47 -60 -83 -117
27
IS0 286-2 : 1988 E)
Basic size h
mm 1 2 3 4 5 6 7 8 9 IO '1 12 13 14') 151) 161) 17 18
..
up to
Above
-
I I
and in-
eluding
3') 0 0 0 0 0
IJm
0 0 0 0
Deviations
0 0
I
0
-
0 I 0 I
mm
0 I 0 I
-0,8 - I,2 - 2 - 3 - 4 - 6 - 10 - 14 - 25 - 40 - 60 -0,' -0,14 -0,25 -0,4 - 0,6
3 6 mm; -;5-;5-; m; 0 ' ' ' ' 0 0 0 0 0 0 0 0
I I -8 - 12 - 18 - 30 - 48 - 75 -0,12 -0,18 -0,3 -0,48 - 0,75 - I,2 - I,8
6 10 -y O O 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
- I,5 - 2,5 - 4 - 6 - 9 -15 -22 - 36 - 58 - 90 -0,15 -0,22 -0,36 - 0,58 - 0,9 - I,5 - 2,2
10 18 ’ ’ ’ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-1,2-2 -3 -5 -8 - 11 - 18 -27 -43 - 70 - 110 -0,18 -0,27 -0,43 -0,7 - I,1 - I,8 - 2,7
18 3o -;5-;5-; -; -; 0 0 0 0 0 0 0 0 0 0 0 0 0
I I - 13 -21 -33 - 52 - 84 - 130 -0,21 -0,33 -0,52 -0,84 - I,3 - 2,l - 3,3
30 50 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-I,5 - 2,5 - 4 - 7 -11 - 16 - 25 - 39 - 62 -100 - 160 -0,25 - 0,39 -0,62 -1 - I,6 - 2,5 - 3,9
50 8o -; -; -g -; O 0 0 0 0 0 0 0 0 0 0 0 0 0
-13 - 19 - 30 - 46 - 74 -120 - 190 -0,3 - 0,46 -0,74 -I,2 -I,9 -3 - 4,6
80 ‘20 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-2,5 - 4 - 6 -10 -15 -22 -35 -54 - 87 -140 - 220 -0,35 - 0,54 -0,87 -I,4 - 2,2 - 3,5 - 5,4
120 180 ’ ’ ’ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-3,5 - 5 - 8 -12 -18 -25 -40 -63 -100 -160 - 250 -0,4 -0,63 -1 -I,6 - 2,5 - 4 - 6,3
180 250 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-4,5 - 7 -10 -14 -20 -29 -4-6 - 72 -115 -185 - 290 -0,46 -0,72 -I,15 -I,85 - 2,9 - 4,6 - 7,2
7w 315 -; ; O O O 0 0 0 0 0 0 0 0 0 0 0 0 0
_ -12 -- 16 -23 - 32 - 52 - 81 -130 -210 - 320 -0,52 -0,81 -I,3 -2,' - 3,2 - 5,2 - 8,l
315 400 -; -; O O O 0 0 0 0 0 0 0 0 0 0 0 0 0
-13 -18 -25 - 36 - 57 - 89 -140 -230 - 360 -0,57 - 0,89 -I,4 -2,3 - 3,6 - 5,7 - 8,9
7””
0 0 0 0 0 0
At-m II 5oo 1 -i I-1: l-1: / -2: / -2; / - : / - 6: 1 - 9; / -15; / -2; 1- 4O:l -,".,3 - 0,97 -I,55 -2,5 - 4 - 6,3 - 9,7
2)
630 0 0 0 0 0 0 0 0 0 0 0 0 0 0
500
- 9 -11 -16 -22 -32 -44 - 70 -110 -175 -280 -2,8 - 4,4 - 7 -11
630 800 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-10 -13 -18 -25 -36 - 50 - 80 -125 -200 -320 - 500 -0,8 -I,25 -2 -3,2 -5 -8 -12,5
800 1 000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-11 -15 -21 -28 -40 - 56 - 90 -140 -230 -360 - 560 -0,9 -I,4 -2,3 -3,6 - 5,6 - 9 -14
1 000 1250 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-13 -18 -24 -33 -47 -66 -105 -165 -260 -420 - 660 -I,05 -I,65 -2,6 -4,2 - 6,6 -IO,5 -16,5
1 250 1 600 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-15 -21 -29 -39 -55 - 78 -125 -195 -310 -500 - 780 -I,25 - I,95 -3,l -5 - 7,8 -12,5 - 19,5
1 600 2 000 0 0 0 0 0 0 0 0 0 0 0 0 0 0
-18 -25 -35 -46 -65 - 92 -150 -230 -370 -600 -6 - 9,2 -15 -23
2 500 0 0 0 0 0 0 0 0 0 0 0 0 0
2 000
-22 -30 -41 -55 -78 -110 -175 -280 -440 -700 -11 -17,5 -28
3 150 0 0 0 0 0 0 0 0 0 0 0 0 0
2 500
-26 -36 -50 -68 -96 -135 -210 -330 -540 -860 -1350 -2,' -3,3 - 5,4 -13,5 -21 -33
-
1) Tolerance grades IT14 to IT16 (incl.) shall not be used for basic sizes less than or equal to 1 m m
2) The values given in the frame, for tolerance grades IT1 to IT5 (incl.), for basic sizes greater than 500 m m and less than or equal to 3 150 mm, are included
for experimental use.
28
IS0 286-2 : 1988 E)
m
- co g
-
w@ l.c I. 3us
r\ -
z K
-
In .
T
m- cyj 4 d d Ii I od a T-
-
d-
-
+I +I +I +I +I +I I +I +I +I + +I +I
- - - - - -
Lo Lo
M co co - KYI In 8 3 m 2
cu c-i 4 cu‘ m- ti i e d u+ cc r; od
+I +I +I +I +I +I I +I +I +I + +I +I
- - - - - -
cow Ki . % co co CYI Ln 00 c? Q: co Ln
0‘ 0‘ - - - G- nl ti i ti cu‘ m (y: d Ii
+I +I +I +I +I +I +I +I I +I +I +I + +I +I
- - - - - - % 76
E
m CD 00
%
0) g . E%. u:
if
. -? L (Dc 00. Ln
.-0 z
0‘ 0‘ 0‘ 0’ - 7 - F- - v-- 2 h m ti ‘i
+I +I +I +I +I +I +I +I I t +I +I +I + +I +I
ii x
- - - - - - d=
E
/ Ti
z K 2 In E 8
F; 2 m In 3 b b 09 . I--
. c? % q cu.
0‘ 0’ d 0’ d d 0‘ 0 F - - r- F 04 .- :
+I +I +I +I +I +I +I +I +I +I +I + +I +I ti
- - - - - -
< -0 -is
5 3
Lo Z8 .-
3
75
%m
- w Fj% g 38 z
R
CD b 3
Fm Lo
- 0‘ 0’ .-t
. . T + I (/Y
0’ 0‘ 0‘ o- d 0‘ 0‘ d 0‘ 0‘ d 0 - 7 5 z
+I +I +I +I +I +I +I +I +I +I +I +, +I +I
ci,
co
- - - - - - ai
7 c
i
m
Lo 2 - E
R Ln 3 zi‘
- T- nl3 3 N Fj %. e % 3 8 ? E I +I
0‘ 0‘ 0‘ 0‘ d 0‘ 0‘ d d d d d 0‘ 0‘ 2
. 0
5:
c-
+I +I +I +I +I +I +I +I +I +I +I +I +I +I II
5 m
- - - - - - -4
QJ .-= -E 0
- -23
z F- 5 5
8 i% z3 63 53 -
- ‘c - FE 8 8 8 9 l.n v)
: *- 2 c
+I +I +I +I +I +I +I +I +I +I +I +I
- - -
+ O aI
- - - 6 -0 6
In .
II
In -- iti- 5
0
23 8 8% g
F
-
7
8
7
3
F- z
55
c\1
8m 53
m
3 E
z E 5
+I +I +I +I +I +I +I +I +I +I +I +I 2 2 5 ii
- - - - - - U 0 2
$ In u
Lo Lo m. E g-
g r\’ 2 fi - E
F;k In 3 4 k- G 8Z
- -
E
7
iz
?
is
- ii P
a +I E’ E
+I +I +I +I +I +I +I +I +I +I +I +I +I +I ii
.-E 0 &EE
- - - - - - .
Ln Lo m. In . 8 Q) 8
:
6 m - CD In LL
- cv F; cr) z iG- 8 2 k - 3 0 F. 0g-;z
- -
+I +I +I +I +I +I +I +I +I +I +I +I .-cn E
z z
- - - - - - .-UY I-G &
L ,r
In In . In . Ln In . m. .-- E & g
cu’ Ln .4 c
- - R R 3 %F; % ti sf g k : E;&g
$ L
+I +I +I +I +I +I +I +I +I +I +I +I
;-? z Iz
- - - - - - E i .!
:
Ln Ln In 5F .- A? E
:
03 oi c-i d co & g ‘;
- - - 212 A 3 % 3 s E
+I +I +I +I +I +I +I +I +I +I +I +I g .; d
!i ?
-- -- -- -- .-; E .g
- --
7 .; y-:
Ln Lo m. In In G m. Ln In . r g ”
lri (0‘ 0-l 0 - ti ti co z
7 - - - 3 2 G! 52 .- 5 0
+I +I +I : +I +I +I +I +I +I +I +I s iii 8 .r
cn 5 as rc -
.-
-
- - - - - -
a
22 .- rJ2 73
% 2
In In . Loc d
, CD r\ 00 6) 0 7 co’ oi CD b I‘hl > 3 g
- - c- 3 R z 2
I +I +I +I +I G +I +I +I +I +I +I CCI E
z
- - - - - - . k Egg
In In In . 12 c= 2 G -g
In In 00 cu k- 3
4
I e m CD co‘ IQ- 7 7 - E -g ‘,-gzl
I +I +I +I +I +I +I +I +I +I +I T > .-c - .
‘i E
- - - - - - 5
; z
G E
I In m Lo t E L3
I. m Lo m ii
Le cn d ti Ln (0 0
N‘ ti Tl- Ti- In T- - c- % !!
I +I +I +I +I +I +I +I +I +I +I as F z
T - 0
\ - - - - - - .-E 5 -t3 0 7.
.-+J
I Ln m LrY ;ij ;
% z
. z z Lo + cd IQ Q, 7 a
U iii
1 --- cu‘ C-Q 6 * -
t? k E 2
I +I fl +I +I +I +I +I +I +I fl z
U
.- z 12
= z; C Z E : 76 -g 2c-’
?
0 I: COO I In IO .- : b .E
+-r *- ‘c I k3g 8 m .-c,
F; % co Q E 0
z
r-- - s z 8 !i
5’ 04 N a
iE
E
E a
:
C
ocfl I
-
s3
LnO
-
0
55
- -
8
-
0
8
-
E
2
0
-c
2
al
rr
.r
73
;I3
5
: -F
aI
1
cv ;5; 3 E cv
:: - - - N -
1 - - - t-
IS0 286-2 : 1988 (El
50 8o :; +12 +18 +lO +15 + 21 +32 +46 + 74 +120 + 190 + 300 + 460
-7 -12 +2 +2 +2 +2 0 0 0 0 0 0
80 120 ‘; +13 +20 +13 +18 + 25 +38 +54 + 87 +140 + 220 +350 +540
-9 -15 +3 +3 +3 +3 0 0 0 0 0 0
120 180 ‘,: +14 +22 +15 +21 +28 +43 +63 +loo +160 + 250 + 400 + 630
-11 -18 +3 +3 +3 +3 0 0 0 0 0 0
180 250 + 7 +16 +25 +18 +24 +33 +50 + 72 +115 +185 + 290 + 460 + 720
-13 -13 -21 +4 +4 +4 d-4 0 0 0 0 0 0
250 315 ‘,; If:16 k26 +20 -1-27 +36 +56 + 81 +130 +210 + 320 + 520 + 810
+4 -I-4 +4 +4 0 0 0 0 0 0
315 400 + 7 +18 +29 +22 +29 +40 +61 +89 +140 +230 + 360 + 570 + 890
-18 -28 -I-4 -I-4 -I4 d-4 0 0 0 0 0 0
400 500 + 7 ItI20 +31 +25 +32 +45 +68 + 97 +155 +250 + 400 + 630 + 970
-20 -32 +5 +5 +5 +5 0 0 0 0 0 0
I F;nn
tiuw 630 +44 + 70 +llO +175 +280 + 440 + 700 +l loo
I 0 0 0 0 0 0 0 0
I
630 800 +50 + 80 +125 +200 +320 + 500 + 800 +l 250
0 0 0 0 0 0 0 0
800 1 000 +56 +90 +140 +230 +360 + 560 + 900 +1400
0 0 0 0 0 0 0 0
2 000 2500 +llO +175 +280 +440 +700 +l loo +l 750 +2800
0 0 0 0 0 0 0 0
2 500 3 150 +135 +210 +330 +540 +860 +1350 +2100 +3300
0 0 0 0 0 0 0 0
I) Where values for j5, j6 and j7 are shown as “ fx”, they are identical with the tolerance class js5, js6 or js7 for that basic size step.
30
IS0 286-2 : 1988 (E)
6 IO + 8,5 +lO +12 + 15 + 21 +28 +42 +12,5 +14 +16 + 19 + 25 +32 +46
+6 +6 +6 + 6 + 6 +6 +6 + 10 +lO +lO + 10 + 10 +lO +lO
10 18 +lO +12 +15 + 18 + 25 +34 +50 +15 +17 +20 + 23 +30 +39 +55
+7 -i-7 +7 + 7 + 7 -I-7 -+7 +12 +12 +12 + 12 + 12 +12 +12
18 30 +12 +14 +17 + 21 + 29 +41 +60 +19 +21 +24 + 28 +36 +48 +67
+8 +8 +8 + 8 + 8 +8 +8 +15 +15 +15 + 15 + 15 +15 +15
+13 +16 +20 + 25 +34 +48 +71 +21 +24 +28 +33 + 42 +56 d-79
30 50
+9 +9 +9 + 9 + 9 +9 +9 +17 +17 +17 + 17 + 17 +17 +17
31
IS0 286-2 : 1988 (El
Basic size
I P
mm
up to
Above and in- 3 4 5 6 7 8 9 IO
eluding
+8 +9 +lO + 12 + 16 + 20 +31 + 46
- 3
+6 +6 +6 +6 +6 +6 +6 + 6
IO I8
+21 +23 +26 + 29 + 36 + 45 +61 +88
+18 +18 +18 + 18 + 18 + 18 +18 + 18
+26 +28 +31 +35 +43 + 55 A-74 +106
I8
3o +22 +22 +22 + 22 + 22 + 22 +22 + 22
30 50 +30 +33 A-37 + 42 + 51 + 65 +88 +126
+26 +26 +26 + 26 + 26 + 26 +26 + 26
50 80 +40 +45 + 51 + 62 + 78
+32 +32 + 32 + 32 + 32
8oo
1loo0
1 1 I I =::I =::I :z I I
I 000 I 250 +186 +225 +285
+120 +120 +120
I 250 I 600 +218 +265 +335
+140 +140 +140
32
IS0 286-2 : 1988 (E)
140
1160
1 I 1ii I : E I 1:i I :‘ZI z I I I 800 2 000 + 492
+400
+55Q
+400
+630
+400
160 180 + 80 + 86 + 93 +108 +131 +550 +615 +720
2 000 2 240
+68 +68 +68 +68 +68 +440 +440 +440
180 200 + 91 + 97 +106 +123 +149 +570 +635 +740
2 240 2500
+77 + 77 + 77 + 77 + 77 +460 +460 +460
200 225 +94 +loo +109 +126 +152 +685 +760 +880
2 500 2 800
+ 80 + 80 + 80 + 80 + 80 +550 +550 +550
I
225 / 250 1 +715 + 790 +910
2 800 3 150
+580 +580 +580
250 / 280 1 /
100 120 +89 + 94 +lOl +114 +133 +166 -I- 798 + 845 + 915
I 400 I 600
+ 79 + 79 + 79 + 79 + 79 + 79 + 720 + 720 + 720
-- ---
+104 +llO +117 +132 +155 + 192 + 912 + 970 +1050
120 140 I 600 I 800
+ 92 + 92 + 92 + 92 + 92 + 92 + 820 + 820 + 820
--- ---
+112 +118 +125 +140 +163 +200 +1012 +l 070 +1150
140 160 I 800 2 000
+lOO +loo +loo +loo +loo +loo + 920 + 920 + 920
--- ----
+120 +126 +133 +148 +171 +208 +l 110 +l 175 +l 280
160 180 2 000 2 240
+108 +108 +108 +108 +108 +108 +looO +l ooo +l ooo
--- -____
+136 +142 +151 +168 +194 +237 +1210 +1275 +1380
180 200 2 240 2 500
+122 +122 +122 +122 +122 +122 +l loo +l loo +l loo
-- ---
+144 +150 +159 +176 +202 +245 +1 385 +1460 +1580
200 225 2 500 2 800
+130 +130 +130 +130 +130 +130 +l 250 +1250 +1250
--- ---
+154 +160 +169 +186 +212 +255 +1535 +1610 +l 730
225 250 2800 3 150
+140 +140 +140 +140 +140 +140 +l 400 +1400 +1400
+174 +181 +190 +210 +239 +288
250 280
+158 +158 +158 +158 +158 +158
+186 +193 +202 +222 +251 +300
280 315
+170 +170 +170 +170 +170 +170
+208 +215 +226 +247 + 279 +330
315 355
+190 +190 +190 + 190 +190 +190
+226 +233 +244 +265 + 297 +348
355 400
+208 +208 +208 +208 +208 +208
+252 +259 +272 + 295 + 329 +387
400 450
+232 +232 +232 +232 +232 +232
+272 + 279 + 292 +315 +349 +407
450 500
+252 +252 +252 +252 +252 +252
34
IS0 286-2 : 1988 (E)
I) Tolerance classes t5 to t8 (incl.) have not been tabulated for basic sizes less than or equal to 24 mm. It is recommended that tolerance classes u5 to u8
(incl.) be used instead. However, if tolerance classes t5 to t8 (incl.) are especially required, they may be calculated from the bases given in IS0 286-I.
35
IS0 286-2 : 1988 (I3
;I
Basic size
V2) Y3’
mm
up to
4bove and in- 5 6 7 8 5 6 7 178
eluding
+ 24 +26 + 30 +34 + 45 + 60
- 3 + 20 +20 + 20 + 20 + 20 + 20
3 6 +33 +36 + 40 +46 +58 + 76
+ 28 +28 + 28 + 28 + 28 + 28
+40 +43 + 49 +56 + 70 + 92
6 IO +34 +34 + 341+341+341+ 341 I I
+443 +51 + 58 +67 +83 + 110
IO I4 +40 +40 + 40 +40 +40 + 40
+66 +53 +56 +63 ~-72 +88 + 115
+39 + 45 + 45 + 45 + 45 + 45 + 45
+68 +80 +63 + 67 + 75 + 87 +106 + 138 + 76 + 84 + 96 +115 d-147
+ 47 +47 +54 +54 +54 +54 +54 + 54 + 63 + 63 + 63 +63 +63
+76 +88 +73 4-n + 85 + 97 +116 + 148 + 88 + 96 + 108 +127 +159
+ 55 +55 +64 +64 +64 +64 +64 + 64 + 75 + 75 + 75 + 75 + 75
+ 93 +107 +91 +96 +105 +119 +142 + 180 + 110 + 119 + 133 +156 +194
+68 +68 +80 +80 +80 + 80 +80 + 80 + 94 + 94 + 94 +94 +94
40 50 + 92 + 97 +106 +120 +108 +113 +122 +136 +159 + 197 + 130 + 139 + 153 +176 +214
+ 81 + 81 + 81 + 81 + 97 + 97 + 97 + 97 -I- 97 -I- 97 + 114 + 114 + 114 +114 +114
50 65 +115 +121 +132 +148 +135 +141 +152 +168 +196 + 242 + 163 + 174 + 190
+102 +102 +102 +102 +122 +122 +122 +122 +122 + 122 + 144 + 144 + 144
65 80 +133 +139 +150 +166 +159 +165 +176 +192 +220 + 266 + 193 + 204 + 220
+120 +120 +120 +120 +146 +146 +146 +146 +146 + 146 + 174 + 174 + 174
80 100 +161 +168 +181 +200 +193 +200 +213 +232 +265 + 318 + 236 + 249 + 268
+146 +146 +146 +146 +178 +178 +178 +178 +178 + 178 + 214 + 214 + 214
100 120 +187 +194 +207 +226 +225 +232 +245 +264 + 297 + 350 + 276 + 289 + 308
+172 +172 +172 A72 +210 +210 +210 +210 +210 + 210 + 254 + 254 + 254
120 140 +220 d-227 +242 +265 +266 +273 +288 +311 +348 + 408 + 325 + 340 + 363
+202 +202 +202 +202 +248 +248 +24a +248 +248 + 248 + 300 + 300 + 300
140 160 +246 +253 +268 +291 + 298 +305 +320 +343 +380 + 440 + 365 + 380 + 403
+228 +228 +228 +228 +280 +280 +280 +280 +280 +280 +340 +340 +340
+ 292 +315 +328 +335 +350 +373 +410 + 470 + 405 + 420 + 443
+252 +252 +310 +310 +310 +310 +310 + 310 + 380 + 380 + 380
+330 +356 +370 + 379 +396 +422 +465 + 535 + 454 + 471 + 497
+284 +284 +350 +350 +350 +350 +350 + 350 + 425 + 425 + 425
+356 +382 +405 +414 +431 +457 +500 + 570 + 499 + 516 + 542
+310 +310 +385 +385 +385 +385 +385 + 385 + 470 + 470 + 470
225 250 +360 +369 +386 +412 +445 +454 -I471 +497 +540 + 610 + 549 + 566 + 592
+w +340 +340 +425 +425 +425
+340 +425 +425 + 425 + 520 + 520 + 520
250 280 +408 +417 +437 +466 +498 +507 +527 +556 +605 + 685 + 612 + 632 + 661
+= +385 +385 +385 +475 +475 +475 +475 +475 + 475 + 580 + 580 + 580
+457 -I477 -l-506 4-548 +557 d-577 +606 +655 -I- 735 + 682 + 702 + 731
280 3'5 z +425
+425 +425 +525 +525 +525 +525 +525 + 525 + 650 + 650 + 650
315 355 +500 +511 +532 +564 +615 +626 +647 + 679 +730 + 820 + 766 -I- 787 + 819
+475 +475 +475 +475 +590 +590 +590 +590 +590 + 590 + 730 + 730 + 730
355 400 +555 +566 -I587 +619 +685 +696 +717 -I-749 +800 + 890 + 856 + 877 + 909
+530 +530 +530 +530 +660 +660 +660 +660 +660 + 660 + 820 + 820 + 820
400 450 +622 +635 +658 +692 +767 +780 +803 +837 +895 + 990 + 960 + 983 +1017
+ 595 + 595 +595 + 595 +74O +74Q +740 +740 +74O + 740 + 920 + 920 + 920
450 500 +687 -I-700 +723 +757 +847 +860 +883 +917 + 975 +l 070 +1040 +1063 +1097
+660 +660 +660 +660 +820 +820 +820 +820 +820 + 820 +l ooo +l ooo +l ooo
I) Fundamental deviations v, x and y are not provided for basic sizes greater than 500 mm.
2) Tolerance classes v5 to v8 (incl.) have not been tabulated for basic sizes less than or equal to I4 mm. It is recommended that tolerance classes x5
to ~8 (incl.) be used instead. However, if tolerance classes v5 to v8 (incl.) are especially required, they may be calculated from the bases given in
IS0 286-I.
3) Tolerance classes y6 to yI0 (incl.) have not been tabulated for basic sizes less than or equal to I8 mm. It is recommended that tolerance classes z6
to zI0 (incl.) be used instead. However, if tolerance classes y6 to yI0 (incl.) are especially required, they may be calculated from the bases given in
IS0 286-I.
36
IS0 286-2 : 1988 (E)
Basic size
Z za
mm
-
4bove and In 6 7 8 9 10 11
lc~:~;l 6 I 7 I 8 I g I I0 I I1
- + 38 + 42 + 46 + 57 + 72 + 92
+ 32 + 32 + 32 + 32 + 32 + 32
3 + 50 + 54 + 60 + 72 + 90 + 117
+ 42 + 42 -I- 42 -I- 42 + 42 + 42
6 I0 :i; 1: :: 1:; + 100 + 132 + 61 + 67 + 74 + 88 + 110 + 142
+42 +42 + 52 + 52 + 52 + 52 + 52 + 52
+ 75 + 82 + 91 + 107 + 134 -I- 174
IO
+ 64 +64 +64 +64 +64 +64
I4 I8 1; 1: 1: + 103 + 130 + 170 + 88 + 95 + 104 + 120 + 147 + 187
+60 +60 +60 + 77 -I- 77 + 77 + 77 4-n -I- 77
I8 24 1 ;: 1 ;; + 106 + 125 + 157 + 203 + 111 + 119 + 131 + 150 + 182 + 228
+ 73 + 73 -I- 73 + 73 + 98 + 98 + 98 + 98 + 98 + 98
24 30 + 101 + 109 + 121 + 140 + 172 + 218 + 131 + 139 + 151 + 170 + 202 + 248
+88 +88 +88 +88 +88 +88 + 118 + 118 + 118 + 118 + 118 + 118
30 40 + 128 + 137 + 151 + 174 + 212 -I- 272 + 164 + 173 + 187 + 210 +248 +308
+ 112 + 112 + 112 + 112 + 112 + 112 + 148 + 148 + 148 + 148 + 148 + 148
40 50 + 152 + 161 + 175 + 198 + 236 + 296 + 196 + 205 + 219 + 242 +280 +340
+ 136 + 136 + 136 + 136 + 136 + 136 + 180 + 180 + 180 + 180 + 180 + 180
50 65 + 191 + 202 + 218 + 246 + 292 + 362 + 245 + 256 -I- 272 +300 +346 + 416
+ 172 + 172 + 172 + 172 + 172 + 172 + 226 + 226 + 226 + 226 + 226 + 226
+ 240 +256 +284 +330 +400 + 293 + 304 +320 +348 +394 +464
65
8o :E + 210 + 210 + 210 + 210 + 210 -I- 274 + 274 -I- 274 -I- 274 -I- 274 + 274
80 100 + 280 + 293 + 312 + 345 + 398 -I- 478 + 357 + 370 + 389 + 422 + 475 + 555
+ 258 + 258 + 258 + 258 + 258 + 258 + 335 + 335 + 335 + 335 + 335 + 335
100 120 + 332 +345 +364 + 397 + 450 + 530 + 422 + 435 + 454 +487 +540 + 620
+ 310 + 310 + 310 + 310 + 310 + 310 +400 +400 +400 +400 +400 +400
120 140 + 390 + 405 + 428 + 465 + 525 + 615 + 495 + 510 + 533 + 570 + 630 + 720
+ 365 + 365 + 365 + 365 + 365 + 365 + 470 + 470 + 470 + 470 + 470 + 470
140 + 455 + 478 + 515 + 575 + 665 +560 + 575 + 598 + 635 + 695 + 785
+ 415 + 415 + 415 + 415 + 415 + 535 + 535 + 535 + 535 + 535 + 535
160 180 + 490 + 505 + 528 + 565 + 625 + 715 + 625 +640 + 663 + 700 +760 +850
+ 465 + 465 + 465 + 465 + 465 + 465 +600 +600 +600 +600 +600 +600
180 200 1 g + 566 + 592 + 635 + 705 + 810 + 699 + 716 -I- 742 -I- 785 +855 +960
+ 520 + 520 + 520 + 520 + 520 + 670 + 670 + 670 + 670 + 670 + 670
200 225 1 EYEi + 621 + 647 + 690 + 760 + 865 -I- 769 + 786 + 812 + 855 + 925 +l 030
+ 575 + 575 + 575 + 575 -I- 575 + 740 + 740 + 740 + 740 + 740 + 740
225 250 + 669 + 686 + 712 + 755 + 825 + 930 +849 + 866 + 892 + 935 +1005 +l 110
+640 +640 +640 +640 +640 +640 + 820 + 820 + 820 + 820 + 820 + 820
250 280 -I- 742 + 762 +791 +840 + 920 +l 030 + 952 -I- 972 +lool +1050 +1130 +1240
+ 710 + 710 + 710 + 710 + 710 + 710 + 920 + 920 + 920 + 920 + 920 + 920
280 315 + 822 + 842 + 871 + 920 +lOOO +l 110 +l 032 +l 052 +1081 +l 130 +1210 +l 320
+ 790 + 790 + 790 + 790 + 790 + 790 +looo +l ooo +l ooo +l ooo +l ooo +lOOO
315 355 + 936 + 957 + 989 +1040 +1130 +l 260 +l 186 +l 207 + 1 239 +1290 +1380 +l 510
+900 +900 +900 +900 + 900 + 900 +1150 +l 150 +1150 +1150 +1150 +1150
355 400 +l 036 +l 057 +1089 +1140 +l 230 +l 360 +l 336 +l 357 +1389 +1440 +1530 +1660
+l ooo +l ooo +l ooo +l ooo +l ooo +looO +1300 +1300 +1300--.~ +1300 +1300 +1300
400 450 +1140 +1163 +l 197 +l 255 +1350 +1500 +1490 +1513 +1547 +1605 +1700 +1850
+l loo +llOO +l loo +l loo +l loo +l loo +1450
450 500 +1290 +l 313 +1347 +1405 +1500 +l 650 +1640
+1250 +1250 +1250 +1250 +1250 +l 250 +1600
:
I) Fundamental z and za are not for basic sizes greater than 500 mm.
37
IS0 286-2 : 1988 E)
Basic size
zb zc
mm
----
up to
qbove and in- 7 8 9 IO 11 7 8 9 IO II
eluding
+ 54 + 65 + 80 + loo + 70 + 74 + 85 + loo + 120
- 3 1: + 40 + 40 + 40 + 40 + 60 + 60 + 60 + 60 + 60
_____
3 6 1: +; 1;; +; + 125 + 92 + 98 + 110 + 128 + 155
+ + + 50 + 80 + 80 + 80 + 80 + 80
6 IO + 82 + 89 + 103 + 125 + 157 + 112 + 119 + 133 + 155 + 187
+ 67 + 67 + 67 + 67 + 67 + 97 + 97 + 97 + 97 + 97
IO I4 + 108 + 117 + 133 + 160 + 200 + 148 + 157 + 173 + 200 + 240
+90 + 90 + 90 + 90 + 90 + 130 + 130 + 130 + 130 + 130
--~
I4 I8 + 126 + 135 + 151 + 178 + 218 + 168 -I- 177 + 193 + 220 + 260
+ 108 + 108 + 108 + 108 + 108 + 150 + 150 + 150 + 150 + 150
I8 24 + 157 + 169 + 188 + 220 + 266 + 209 + 221 + 240 + 272 + 318
+ 136 + 136 + 136 + 136 + 136 + 188 + 188 + 188 + 188 + 188
-~
24 30 + 181 + 193 + 212 + 244 + 290 + 239 + 251 + 270 + 302 +348
+ 160 + 160 + 160 + 160 + 160 + 218 + 218 + 218 + 218 + 218
--
30 40 + 225 + 239 + 262 + 300 + 360 + 299 + 313 + 336 -I- 374 +434
+ 200 + 200 + 200 + 200 + 200 + 274 -I- 274 -I- 274 + 274 -I- 274
-~
40 50 + 267 + 281 + 304 + 342 + 402 + 350 + 364 -I- 387 + 425 + 485
+ 242 + 242 + 242 + 242 -I- 242 + 325 + 325 + 325 + 325 + 325
-~
50 65 + 330 +346 -I- 374 + 420 + 490 + 435 + 451 -I- 479 + 525 + 595
+ 300 + 300 + 300 + 300 + 300 + 405 + 405 -I- 405 + 405 + 405
-~
65 8o :z :“;“, :z + 480 + 550 + 510 + 526 + 554 +600 + 670
+ 360 + 360 + 480 + 480 + 480 + 480 + 480
--~
80 100 + 480 + 499 + 532 + 585 + 665 + 620 + 639 -I- 672 + 725 + 805
+ 445 + 445 + 445 + 445 + 445 + 585 + 585 + 585 + 585 + 585
100 120 +560 + 579 + 612 + 665 + 745 + 725 + 744 -I- 777 + 830 + 910
+ 525 + 525 + 525 + 525 + 525 +690 + 690 + 690 + 690 + 690
120 140 + 660 +683 + 720 + 780 + 870 +840 + 863 + 900 + 960 +l 050
+ 620 + 620 + 620 + 620 + 620 + 800 + 800
---+ 800 + 800 + 800
140 160 + 740 + 763 + 800 + 860 + 950 + 940 + 963 +looO +1060 +l 150
+ 700 + 700 + 700 + 700 + 700 + 900 + 900 + 900 +900 + 900
160 180 + 820 +843 + 880 + 940 +l 030 +1040 +1063 +l 100 +l 160 +l 250
+ 780 + 780 + 780 + 780 + 780 +l ooo +l ooo +looO +l ooo +l ooo
180 200 + 926 + 952 + 995 +1065 +1170 +l 196 +1222 +l 265 +1335 +1440
+ 880 +880 + 880 + 880 +880 +l 150 +1150 +1150 +1150 +1150
200 225 +1006 +l 032 +l 075 +1145 +l 250 + 1 296 +1322 +l 365 +1435 +1540
+ 960 +960 +960 +960 +960 +l 250 +l 250 +l 250 +1250 +1250
225 250 +1096 +1122 +1165 +l 235 +1340 + 1 396 +1422 +l 465 +1535 +1640
+1050 +1050 +1050 +l 050 +l 050 +1350 +l 350 +l 350 +1350 +1350
--~
250 280 +l 252 +1281 +1330 +1410 +l 520 +l 602 +1631 +l 680 +1760 +l 870
+l 200 +1200 +1200 +1200 +1200 +1550 +l 550 +l 550 +1550 +1550
280 315 +l 352 +1381 +1430 +l 510 +l 620 +l 752 +l 781 +l 830 + 1 910 +2020
+1300 +1300 +1300 +1300 +1300 +1700 +1700 -~+1700 +1700 +1700
315 355 +l 557 +1589 +1640 +l 730 +1860 +l 957 +1989 +2040 +2130 +2260
+1500 +1500 +1500 +1500 +1500 + 1 900 +1900 + 1 900 +1900 +1900
+l 707 +1739 +1790 +1880 +2010 +2157 +2189 +2240 +2330 +2460
355 400
+1650 +1650 +1650 +1650 +1650 +2100 +2100
-- +2100 +2100 +2100
I
400 450 +1913 + 1 947 +2005 +2100 +2250 +2463 -12497 +2555 +2650 +2800
+1850 +1850 +1850 +l 850 +1850 +2400 +2400 +2400 +2400 +2400
+2163 +2197 +2255 +2350 +2500 +2663 +2 697 +2755 +2850 +3000
450 500
+2100 +2100 +2100 +2100 +2100 +2600 +2600 +2600 +2600 +2600
I) Fundamental deviations zb and zc are not provided for basic sizes greater than 500 mm.
38
IS0 286-2 : 1988 (E)
Annex
A graphical review of a broad selection of tolerance classes for holes is given in figures 6 and 7. Figure 6 shows the tolerance classes in
terms of the fundamental deviation (A to ZC), whereas figure 7 gives the same information in terms of the standard tolerance grade
(IT5 to IT1 1). Figures 6 and 7 do not include all the tolerance classes given in this part of IS0 286 and reference should be made to the
tables for specific details.
For comparative purposes, the tolerance classes given in figures 6 and 7 illustrate the values for ES, EI and IT given for the basic size
step from 6 to 10 mm. Where there are no tabulated values for this basic size step, i.e. those tolerance classes involving fundamental
deviations T, V and Y, the values have been given, again for comparative purposes, for the basic size step from 24 to 30 mm.
A graphical review of a broad selection of tolerance classes for shafts is given in figures 8 and 9. Figure 8 shows the tolerance classes
in terms of the fundamental deviation (a to zc), whereas figure 9 gives the same information in terms of the standard tolerance grade
(IT5 to IT1 1). Figures 8 and 9 do not include all the tolerance classes given in this part of IS0 286 and reference should be made to the
tables for specific details.
For comparative purposes, the tolerance classes given in figures 8 and 9 illustrate the values for es, ei and IT given for the basic size
step from 6 to 10 mm. Where there are no tabulated values for this basic size step, i.e. those tolerance classes involving fundamental
deviations t, v and y, the values have been given, again for comparative purposes, for the basic size step from 24 to 30 mm.
39
IS0 286-2 : 1988 (El
B C CD 0 E EF F FG G H J
9 n 13 9 11 13 7 9 6 * lo I2 5 7 9 5 7 91 ISI 171PI A I71 PI A l-4 I91 A PI PI II’
1 PI .I7
Pm 3 10 12 8 10 12 6 8 IO 7 9 1113 6 8 IO 6 8 IO 6 8 10 6 8 10 6 8 IO 6 8 10 12 6 8
+ 500
+400
+300
+200
+I00
Zero line
0
(concluded)
- 100
Figure 6 - Graphical review of tolerance classes for holes in terms of fundamental deviations
40
ISO286-2: 1988 (E)
I- ~~~
ITC 1 ITL I IT7 1 ITQ
+ 100
+ 200
+ 100
II Zero line I I I
I I I I I I I I I I I I I I I I I I I I I I I
Figure 7 - Graphical review of tolerance classes for holes in terms of standard tolerance grades 41
IS0 286-2:1988 E)
-100
- 200
- 300
-400
-
- 500
I I ,
(concluded )
.
1s k m n p r s t u v x y z za zb zc
8 10 12 5 7 9 l-l 5 7 57575757 5 7 5 7 9 51 171 51 171 191 61 18 171 191 61 181 II0 181 110 181 ho
Pm I 9 11 13 6 8 10 12 6 8 6 8 6 8 6 8 6 8 6 8 6 8 10 6 8 6 8 IO 7 6 8 IO 7 9 7 9 7 9
I I I I I I I II I I I I IBI I I I I I I II I I I I II I I II I I I I II II I I I I H
+ 100
Figure 8 - Graphical review of tolerance classes for shafts in terms of fundamental deviations
42
Is0 286-2 : 1988 E)
IT5 IT6
I-lm
- 100
- 200
- 300
Figure 9 - Graphical review of tolerance classes for shafts in terms of standard tolerance grades