Professional Documents
Culture Documents
Changes On Electric Motors
Changes On Electric Motors
Changes On Electric Motors
This motor simplifies its mechanical design to restrict the flow of current toward a rotary part;
however, it complicates the design because some kind of switching system must be employed to
20 transmit the power toward the different windings. This mechanical design can also be used for a
generator. The load can be switched toward the coils within the sequence to coordinate the flow of
current through the rotation. So these generators can also run at high speed as compared with
conventional types of motors because the armature is made like a single piece of magnetizable
material like a slotted cylinder.
25 Working Principle
The working principle of the switched reluctance motor is, it works on the principle of variable
reluctance that means, the rotor of this motor constantly tries to align through the lowest reluctance
lane.
The formation of the rotary magnetic field can be done using the circuit of power electronics
30 switching. In this, the magnetic circuit’s reluctance can mainly depend on the air gap. Therefore, by
modifying the air gap among the rotor as well as a stator, we can also modify the reluctance of this
motor.
Here, reluctance can be defined as resistance toward the magnetic flux. For Electrical circuits,
reluctance is the combination of resistance as well as the magnetic circuit.
When the poles are opposite then the field coils will be connected in series. So their magnetomotive
forces are additive which are called phase windings. A set of coils or a single-coil can comprise phase
windings. Each winding can be connected to the motor terminal and these are properly connected
45 toward the o/p terminals of a switching circuitry of power semiconductor. The input of this is a DC
supply.
The designing of the rotor can be done with Si steel stampings through externally projected poles.
The rotor poles are dissimilar as compared with the stator poles. In most of the existing motors, the
rotor poles are 4 otherwise 6 based on the number of stator poles like 6 8. The shaft of the rotor holds
50 a position sensor. So the operating of various devices in the power semiconductor circuitry is mainly
controlled through the signals attained from this sensor.
In this motor, both the stator as well as rotor includes a projected pole that is designed with a soft iron
as well as silicon stampings which are used for reducing hysteresis losses. The stator of the motor
includes a field winding whereas the rotor doesn’t. In the stator, each winding can be connected
55 within the series through the opposite poles for increasing the magnetomotive force of the circuit.
70 The stator of this motor includes windings that are related to a BLDC motor; however, the design of
the rotor can be done with steel that is turned into salient poles without magnets or windings. Once
the poles of the stator & the rotor are out of position, then the magnetic circuit among them includes
a high reluctance.
When the pairs of the pole in the stator are switched, the rotor switches to connect through the
75 activated stator poles to reduce the reluctance of the circuit. When the stator poles are switched then
they should be exactly timed to make sure that it happens because the rotor pole is moving toward to
connect with the activated stator pole.
Not like stepper motors, these motors need position feedback using Hall Effect sensors otherwise an
encoder to manage the stator currents commutation depending on the exact position of the rotor.
80 As compared with stepper motors, these motors include fewer poles as well as a larger stepping
angle. Stepper motors are mainly used for placing applications, wherever high resolution, as well as
step integrity, is significant. But SRMs are applicable where a primary concern is power density.
These motors include rotors without windings, magnets & lower inertia. Thus, they can attain higher
3
Primer Examen Parcial Comprensión de Lectura en Ingles para I.M.E.
Profa. Martha Patricia Martínez Miranda
What is a Switched Reluctance Motor & Its Working
speeds as well as accelerations as compared with stepper motors because they have permanent
85 magnet rotors.
The main difference between SRMs (switched reluctance motors) & stepper motors is the construction
of stator. In an SRM, the phases are autonomous with each other that means, if one otherwise more
phases stop working, then the motor will operable even though by decreased torque output.
Switched reluctance motors generate more clear noise as compared with stepper motors. The main
90 source of noise can be the distortion of the stator because of the radial forces that happen once the
pairs of stator poles are activated. These pairs are attracted to cause radial forces to alter the stator.
Advantages
105 These motors are very simple & the rotors in this motor are extremely strong
These motors are applicable for high-speed applications.
The VFDs (variable frequency drives) of this motor are somewhat simpler as compared with
conventional VFDs.
This motor doesn’t use any additional ventilation system when the stator, as well as rotor slots,
110 is projected. So the airflow can be maintained among the slots.
These are less expensive because of the nonexistence of permanent magnets.
Fault tolerance is high
This motor works with a simple two-phase or three-phase pulse generator.
Phase losses do not change the operation of the motor.
115 Once the phase sequence is changed then the motor direction will be changed.
Inertia Ratio or High Torque
Self-starting without using additional arrangements
Disadvantages
120 Switched reluctance motors have less torque capacity & normally these motors are noisy.
While operating this motor at high speed, it creates a torque ripple.
High noise level
It uses an external rotor position sensor
These are applicable for medium to high speed, low-cost applications wherever controllability
125 & shaft or noise torque ripple are not dangerous.
4
Primer Examen Parcial Comprensión de Lectura en Ingles para I.M.E.
Profa. Martha Patricia Martínez Miranda
What is a Switched Reluctance Motor & Its Working
This motor generates harmonics when it operates at high speed, so to reduce this, large size
capacitors need to install.
Since the nonexistence of a permanent magnet, the SRM has to carry a high i/p current to
increase the necessity of converter KVA.
130 Applications
These types of motors are used as an alternative for induction motors in different applications
wherever the operating conditions of this motor do not suit them.
In textile machinery like towel looms, rapier looms, etc
135 Used in electric vehicles
Oilfield machinery like beam pumps, vertical pumps, well testing machinery, etc.
Mining machinery like conveyors, shearers, winches, ball mills, boring machines, coal crushers,
etc.
Used in all kinds of mechanical presses like screw presses.
140 These motors are used in miscellaneous applications which include the following.
Thus, this is all about an overview of switched reluctance motors (SRMs). These motors have many
benefits in different applications. At present, the linear version of this motor has been implemented to
process the same attributes as well as prospects by owing their design & high force density.