Professional Documents
Culture Documents
BES 122 Quiz 1
BES 122 Quiz 1
BES 122 Quiz 1
MULTIPLE CHOICE
Instruction: Write the letter of the correct answer, have it scan or take picture of the answers and send to
google classroom.
a)
b)
c)
d)
a)
b)
c)
d)
24. Short-break lines are drawn freehand while long-break lines are ruled lines.
a) True
b) False
25. In engineering drawing, which type of line indicates that there is a change of plane?
a) Continuous thin wavy
b) Long chain thin
c) Continuous thick
d) Medium thick short dashes
26. Which of the following lines are used to show that the object is cut and then viewed?
a) Hidden lines
b) Leader lines
c) Centre lines
d) Hatching Lines
27. What do hidden lines in orthographic projections denote?
a) Holes or slots
b) Change of Plane
c) Position of cut
d) Centre of a circle or cylinder
28. From the below figure, what is the name of the line X?
a) Outline
b) Section line
c) Hidden line
d) Hatching
a) Continuous thick
b) Continuous thin straight
c) Medium thick short dashes
d) Continuous thin wavy
30. The axis of the cylinder or sphere is denoted by which of the following line?
a) Section line
b) Centre line
c) Hidden line
d) Leader line
31. What is the standard length and width of the arrowhead of dimension lines?
a) 2mm and 2mm
b) 3mm and 1mm
c) 4mm and 2mm
d) 3mm and 2mm
32. What is the length of the short dashes of the centre lines?
a) 5mm
b) 2mm
c) 1mm
d) 3mm
33. Among the following, which of the representation is wrong?
a)
b)
c)
d)
34. Which type of line is used to join the dimension line and the curve that needs to be
dimensioned?
a) Leader line
b) Outline
c) Dimension line
d) Section line
a) 30
b) 70
c) 10
d) 20
a) 22.5
b) 15
c) 20
d) 35
42. Dimension lines should not intersect each other as far as possible.
a) True
b) False
44. As far as possible, the dimension should be given to which of the following lines?
a) Outline
b) Hidden line
c) Center line
d) Leader line
a) dimension line
b) hidden line
c) centre line
d) outline
47. Identify the ‘a’ in the below given picture.
a) dimension line
b) outline
c) leader
d) extension line
a) a, i; b, ii; d, iii; e, iv
b) a, iv; b, iii; d, ii; e, i
c) a, i; b, iv; d, iii; e, ii
d) a, iii; b, ii; d, i; e, iv
50. Identify the note in the below given figure.
a) A
b) B
c) C
d) D
51. It is recommended that a gap of about 2 mm should be kept between the extension line and an
outline.
a) True
b) False
53. Which of the lines is a thin continuous line with the ends terminating in arrowheads and is
enclosed by extension lines, outlines or centre lines?
a) Dimension line
b) Leader line
c) Extension line
d) Section line
54. What is the name of the thin continuous line which encloses the dimension lines are generally
drawn 1mm away from the outlines?
a) Dimension line
b) Section line
c) Leader line
d) Extension line
57. Which of the following is a thin continuous line with one side terminating in arrowhead and the
other with a period?
a) Note
b) Extension
c) Leader
d) Dimension
61. While dimensioning a feature with a square cross-section, what should be added before the
dimension figure?
a) SQUARE
b) SQ
c) Sq
d) Nothing
62. While dimensioning a sphere, what should be added in front of the dimension figure?
a) Sp
b) Sq
c) SPHERE
d) φ
63. Operations performed on a particular feature are indicated by using extension lines.
a) True
b) False
64. Tapers and slope indicated in the view are part of dimensioning.
a) True
b) False
65. What is the type of scale in which the representative fraction is 1:1?
a) Enlarged scale
b) Reduced scale
c) Full size scale
d) Graphical scale
66. A scale which is numerically represented on the drawing sheet is called as _____
a) Graphical scale
b) Engineer’s scale
c) Reducing scale
d) Full size scale
68. The minimum length to be shown must be known for drawing an unusual scale.
a) True
b) False
69. Which of the following is used in checking the instruments to measure angles with great
accuracy?
a) Circular Vernier scale
b) Plain scale
c) Diagonal scale
d) Comparative scale
70. Which of the following scales represent two different units having the same representative
fraction?
a) Plain scale
b) Diagonal scale
c) Comparative scale
d) Vernier scale
71. Which of the following is used to set or measure angles when a protractor is not available?
a) Plain scale
b) Diagonal scale
c) Scale of chords
d) Comparative scale
72. Why it is more beneficial to represent the scale graphically other than by just numerical?
a) To represent clearly
b) More accurate
c) To measure directly from scale
d) To prevent
73. What is not essential information to construct a scale from the following?
a) The R.F. of the scale
b) The units to represent
c) Length of scale
d) Maximum length
76. A tangent to a circle is a line which touches the circle at one and only one point.
a) True
b) False
84. The line perpendicular to a tangent and is passing through the point of contact is called as _____
a) Perpendicular bisector
b) Angle bisector
c) Normal
d) Tangent
77. In the following figure, the tangent at point A can be drawn by _______
a) Angle bisector
b) Perpendicular bisector
c) Rectangle
d) Arc
78. How many tangents to a given circle, can we draw parallel to a given line?
a) 1
b) 2
c) 3
d) 4
79. The straight lines which are drawn from various points on the contour of an object to meet a
plane are called as _________
a) connecting lines
b) projectors
c) perpendicular lines
d) hidden lines.
80. When the projectors are parallel to each other and also perpendicular to the plane, the
projection is called ___________________________
a) Perspective projection
b) Oblique projection
c) Isometric projection
d) Orthographic projection
81. The object we see in our surrounding usually without drawing came under which projection?
a) Perspective projection
b) Oblique projection
c) Isometric projection
d) Orthographic projection
82. In orthographic projection, each projection view represents how many dimensions of an object?
a) 1
b) 2
c) 3
d) 0
83. In orthographic projection an object is represented by two or three views on different planes
which _________________
a) gives views from different angles from different directions
b) are mutually perpendicular projection planes
c) are parallel along one direction but at different cross-section
d) are obtained by taking prints from 2 or 3 sides of object
84. To represent the object on paper by orthographic projection the horizontal plane (H.P) should
be placed in which way?
a) The H.P is turned in a clockwise direction up to 90 degrees
b) The H.P is turned in anti-clockwise direction up to 90 degrees
c) H.P plane is placed to left side of vertical plane parallel to it
d) H.P plane is placed to right side of vertical plane parallel to it
85. The hidden parts inside or back side of object while represented in orthographic projection are
represented by which line?
a) Continuous thick line
b) Continuous thin line
c) Dashed thin line
d) Long-break line
86. Orthographic projection is the representation of two or more views on the mutual
perpendicular projection planes.
a) True
b) False
87. What is additional 3rd view on orthographic projection in general for simple objects?
a) Front view
b) Top view
c) Side view
d) View at 45 degrees perpendicular to horizontal plane
90. A plate of a negligible thickness of circular shape is placed parallel to horizontal plane the front
view will be ____________
a) line
b) circle
c) rectangle
d) ellipse
91. A regular tetrahedron is placed on horizontal plane on one of its base, the front view, top view
and side view gives triangle.
a) True
b) False
92. A regular cone is placed on horizontal plane on its base the top view is _____________
a) circle
b) rectangle
c) square
d) triangle
93. The views will change if we keep the object in different quadrants.
a) True
b) False
94. A Square pyramid is resting on vertical plane with base parallel to vertical plane. The side view
will be _____________
a) triangle
b) polygon with 4 sides
c) square
d) polygon with 5 sides
95. A triangular prism is placed in projection plane such that the square surface is parallel to
horizontal plane. The top view, front view will be __________
a) square, rectangle respectively
b) rectangle, triangle respectively
c) rectangle, rectangle respectively
d) triangle, rectangle respectively
96. If an isometric drawing is made use of isometric scale then the drawings are called ___________
a) Isometric projection
b) Isometric view
c) Isometric perception
d) Orthographic view
a)
b)
c)
d)
a)
b)
c)
d)
a)
b)
c)
d)
b)
c)
d)
GOODLUCK!