Professional Documents
Culture Documents
Product Data Sheet: Hempafloor Durable 300
Product Data Sheet: Hempafloor Durable 300
Recommended use: Designed to concrete substrates exterior and interior in areas exposed to heavy abrasion such
as car parks, garages and warehouses. The flexible coating surface can withstand the stresses
that rubber tyres impart onto the flooring system. Also designed to use as UV-protective
topcoat on Hempafloor epoxy-based paints to improve gloss retention. For enhanced slip
resistance we recommend to broadcast Hempafloor Antislint in the system.
Availability: Available in 5L, 20L. (Packing may vary from country to country depending on local requirements).
Physical constants*:
Colours/shade Nos.: According to Hempafloor Colour Card
Finish: Glossy
Volume solids, %: 51± 2
Theoretical spreading rate: 6.8 m²/litre/coat – 75 microns DFT**
Flash point: >31°C
Specific gravity: 1.26 kg/litre
Dry to touch: 8 hours at 10°C 4 hours at 20°C 2 hours at 40°C
Initial hardness: 24 hours at 20°C
Fully cured: 7 days before the floor can be exposed to heavy duty traffic
VOC content: 444 g/litre
*The physical constants stated are nominal data according to the Hempel Group's approved formulas.
They are subject to normal manufacturing tolerances and where stated, being standard deviation
according to ISO 3534-1.
**The theoretical spreading rate has been calculated for the stated volume solids and dry film thickness. A
practical spreading rate will depend on the actual dry film thickness, the nature of the substrate and
relevant consumption factor. The physical constants are subject to normal manufacturing tolerances.
Further references can be found in the "Explanatory Notes".
Application details:
Mixing ratio: 84:16 on volume
Application method: Brush, short haired roller
Thinner (max.vol.): Maximum 5% dilution if required with thinner 08080
Pot life: 3 hours at 20°C Reduced at higher temperature
Cleaning of tools: Hempel Tool Cleaner 99610
Indicated film thickness, dry: 2 x 75 microns
Indicated film thickness, wet: 2 x 140 microns
Overcoat interval, min: 48 hours at 10°C 24 hours at 20°C 12 hours at 40°C
Safety: Handle with care before and during usage. Read all labels on packaging and paint containers
before usage, consult Hempel for any inquiries. Material Safety Data Sheets follows all local
and national safety regulation. Avoid inhalation; avoid contact with eyes and skin. Do not
swallow. Take precautions against possible risks of fire or explosion. Apply only in well-
ventilated areas. Remember to protect the environment.
Substrates: Concrete.
Application conditions: Application can only proceed at temperatures above 10°C, and relative humidity below 75%.
Other sealer/filler types may be specified. Drying data are given on the assumption that proper
ventilation is provided. Hempafloor Durable 300 should not be applied to concrete with more
than 4% moisture.
Surface preparation: The surface should be stable, firm, dry and free from dust, sand, loose old paint, laitance, dirt,
grease and oil. Proper surface preparation is a must, mechanical surface preparation is highly
recommended.
Sealing/Priming: Hempafloor Prime 420 or Hempafloor Prime 100. Recommendation: apply primer/sealer prior
to the application of a specified filler.
Mixing: Hempafloor Durable 300 is a two-component material (base and curing agent), which must be
mixed together prior to use. Stir the base continuously while adding the contents of the curing
agent. Mix until the mixture is homogeneous.
Application: Apply the mixed product to the surface with a good quality short haired roller or brush.
Storage & handling: Product must be stored as per local regulation. Keep in dry and ventilated location, far from
heat and direct sunlight.