Professional Documents
Culture Documents
MCTC-ARD-C Series: Elevator Auto Rescue Device User Manual
MCTC-ARD-C Series: Elevator Auto Rescue Device User Manual
MCTC-ARD-C Series: Elevator Auto Rescue Device User Manual
The ARD can be mounted in the wall or on the floor. Output terminals Ground
◆ Designation Rules T K1 and K2 of the main board S1 are at ON Main circuit
MCTC-ARD-C Series
M6: corresponds to Y6
MCTC - ARD - C - 40 - 15
Y1 X20
M1 signal state; 1 2
K1 K2
2: ON Output 1-phase 380 V ON
DIP
M1
Emerg. evacuation
startup signal TB:JX2
24V
switch
1 2
Mark Series Mark Power Rating (1) Wall-mounting diagram OFF when the ARD exits the emergency K1 K2
Y2
TB:JXS1
124
(2) Floor-mounting diagram Y2 Phase sequence ON Phase sequence
Three-phase You need to remove the front cover before wiring the power cables and that emergency running is completed. It COM in control cabinet M6
40 Evacuation
380 V control circuit. DI1
completion signal
stops output, exits the emergency running
Note: For 380 V input and 220 V output (with the neutral line), boh K1 and
19010431 B01
state and waits for system power-on.
A B
Loosen and remove the four screws on the front cover and remove the If the ARD does not receive this signal, it K2 must be in ON position.
A
◆ Technical Specifications cover. automatically stops output after running for 3
Figure 7 Electric wiring diagram for single-phase 220 V
Front view Left view Front view Left view minutes.
Wall-mounting Floor-mounting Figure 4 Diagram of removing front cover
Table 1 Technical specifications of MCTC-ARD-C-4015 If J19 on the drive board is closed, when a Power input
Power output
cables
Control cabinet
1
Power Integrated
low level signal (0-0.8 V) is input at DI2 or cables
elevator controller
brake release. N1
cable PE
(kg)
220V Safety circuit
CAN
1
device (ARD).
3
0V
Power of door
communication
4
MCTC-ARD-C-4018, ≤ 18.5 KW It connects to the auxiliary contact of the 2: ON Output 1-phase 380 V ON
Y1
Emerg. evacuation
X20
vance Technology, and well matches Inovance NICE series elevator main air switch to turn off the main air switch
1 2
K1 K2
DIP
switch M1
startup signal TB:JX2
24V
cable to the control system running in the light load direction. Protection MCTC-ARD-C-4007 terminating signal 1: ON Input 3-phase 380 V
M2
shorting signal TB:JXS2
130
Output short circuit, overcurrent, and battery protection functions Valid with low level (0 to 0.8 V) or when the 2: ON Output 1-phase 220 V
248.0 217.0 383.4 480.0 430.0 151.2 15
1 2
functions
K1 K2
flammable gas, metal powder, oil mist or dust 1: OFF Input 3-phase 220 V
2: OFF Output 1-phase 220 V CANL
Reserved CAN signal TB:CAN-
CANL
specifications, mounting dimensions, terminals, installation and commis- MCTC-ARD-C-2015 K1 K2 Function
1 2
K1 K2
Emerg. evacuation
completion signal TB:X1
< 1000 m (derated or consult Inovance if above 4
DI1 Y6: control cabinet output
OFF
ON
ON
OFF
K5 'OXY]OZIN
The manual is subject to update without notice. You can obtain the lat- MCTC-ARD-C-4015
ON
Y1
No. Component Specifications MCTC-ARD-C-2018 system.
M1
303.0 272.0 383.4 431.7 99.0 151.2 17 K5
◆◆
Y2
1 MCB ARD3T153U2 MCTC-ARD-C-4030 Program burning The jumper is in OFF position (pins 2 and 3
M2
DI1
jumper shorted) at delivery. Do not change it.
ON
N1
2 Drive board ARD3T153M2 MCTC-ARD-C-2030 IOXI[OZ
ZKXSOTGRY K1 K2 N
The device is exposed to high voltage which can cause severe MCTC-ARD-C-4003 with 12 V x 4.5 Ah x 3 J10 BOOT
T
Install the ARD according to the required dimensions in one of the follow-
D1 D2 D3 D4 D5 8UIQKXY]OZIN
The DIP switches K1 and K2 have been configured to match the
ON
WARNING electric shock or even death. Exert extreme caution when using or MCTC-ARD-C-4007 with 12 V x 5.5 Ah x 3 1 2
S2
S
getting close to the energized device. ing methods. WARNING three-phase 380 V model. Do not change them yourself. If a three-
3 Battery MCTC-ARD-C-4015 with 12 V x 7 Ah x 3 R
ON phase/single-phase 220 V model is required, contact
MCTC-ARD-C-4018 with 12 V x 7 Ah x 3 3GOTVU]KXZKXSOTGRY L1 L2 L3 N1 N R S T L3
ON ON
The device provides the emergency running function in the case of OFF
It is inhibited to ensure personal safety by using the startup, stop 4 Contactor Coil voltage 220VAC-main contact 380
or input signals of the device during elevator maintenance as these 18.5 kW VAC/50 A
CAUTION signals cannot isolate dangerous voltage. 30 kW
Auxiliary contact 1NC+1NO
Before electric wiring, use a reliable insulating component to
disconnect power supply of the elevator. 5 Air switch 400 VAC/63 A
7 8 9 10 11 12
Figure 8 Emergency operation flowchart 6. Repair and Maintenance 7. Troubleshooting Fault Display Description Troubleshooting
Warranty Agreement
Power failure 7. Troubleshooting
Commissioning Description
Power failure duration ◆ Status Indicators Busbar Fault is reported when the voltage of the busbar
1. The warranty period of the product is 2 years (refer to the barcode
20s confirmed
Bottom cover
overvoltage exceeds 780 V for 10 ms. on the equipment). During the warranty period, if the product fails
1. Power-on of MCB
Figure 8 Diagram of status indicators or is damaged under the condition of normal use by following the
N Y
No fault ARD discharges ARD sends Elevator enters Ensure that the air switch K5 and rocker switch K4 are on OFF instructions, Inovance will be responsible for free maintenance.
/Fault emerg. running
auto-reset AC380V/AC220V request emerg. running position and carry out wiring according to Figure 5 Fault Power
Turn on K5, attach the front cover, fasten the screws, and then indicator indicator 2. Within the warranty period, maintenance will be charged for the
N turn on K4 Power cutoff damages caused by the following reasons:
Normal and emergency power supply are
Completion Battery cover fault reported
Y prohibited. Apart from K3, K1, K2 and K4 are
signal
by the a. Improper use or repair/modification without prior permission
received
2. Commissioning preparation opened and the fault code gives indication.
No fault
Y
ARD keeps output ARD emerg. Fault controller
/Fault
auto-reset AC380V/AC220V running ends b. Fire, flood, abnormal voltage, other disasters and secondary
Y
Switch on the main power,and check that the elevator running disaster
N 3 min emerg. and functions are normal
running done
Check the battery capacity, and ensure that 3 to 4 power ◆ Common Symptoms c. Hardware damage caused by dropping or transportation after
indicators are on Battery Battery capacity
N
procurement
Descriptions of power indicators Table 6 Common symptoms and troubleshooting
Mains power
is normal
Y
Switch to mains d. Improper operation
Faulty & emerg. running
power supply 3.First-time commissioning Power Indicator Status Description No. Fault Symptoms Causes Troubleshooting
ended for 20s
Each indicator displays 25% of the battery capacity. e. Trouble out of the equipment (for example, external device)
N Do not carry out Commissioning at the bottom or top floor. 1. The drive board or 1. Power on the ARD
Run the elevator to a middle floor, and then in the up or down The LED on the left blinks during charging. There is no power MCB is damaged. again, replace the board or
2 min ARD powers off
direction.
3. If there is any failure or damage to the product, please correctly fill out
/battery below Emerg. running The LEDs becomes off from right to left during discharging. 1 input or phase loss 2. The contactor is contactor.
28 V failed Cut off the main power when the elevator is in non-door zone Take out the battery to be replaced as follows: the Product Warranty Card in detail.
area. exists. damaged due to incorrect 2. Check that the wiring is
Remove the two screws on upper part of the battery cover. ◆ Faults and warnings with display wiring of output cables. correct. 4. The maintenance fee is charged according to the latest Maintenance
The ARD has a 1. Check the battery voltage Price List of Inovance.
Push downward the battery cover, and disconnect the cables on the bat- Table 5 Troubleshooting of common faults and warnings with display 1. The battery voltage is
●
●When the mains power to the elevator control cabinet, and the elevator 4.Emergency running relative low voltage 2. Try again after the
tery. low. 5. The Product Warranty Card is not re-issued. Please keep the card and
restores to normal running state. 2 and cannot support heatsink cools down and the
Fault Display Description Troubleshooting 2. The thyristor is present it to the maintenance personnel when asking for maintenance.
When the elevator cannot run, turn K4 switch of the ARD to Take out the battery from the battery box. emergency running battery voltage restores to
overheated.
2. Forced evacuation OFF position, and switch off the power supply of the elevator. Short circuit It is a non-resettable hardware overcurrent fault. of the elevator. normal.
6. If there is any problem during the service, contact Inovance’s agent or
Open the front over, and turn off switch K5 of the ARD, and (overcurrent) Eliminate the causes, and power on the ARD
Forced evacuation is for the situation where there is power failure of the check whether wiring is correct. 1. Check the wiring and Inovance directly.
on output side again.
The ARD circuit check that the elevator
mains power and the ARD has terminated normal evacuation but you Output abnormality or 7. This agreement shall be interpreted by Suzhou Inovance Technology
When the NTC of the heatsink detects that 3 board is damaged. controller power matches
want to start ARD output again. When J19 on the drive board and DI2 overcurrent exists.
Repair and Maintenance Over-
the temperature reaches 90°C, the ARD the ARD power. Co., Ltd.
are closed, ARD output is started. The jumper connected to J19 must be automatically stops output, and restores to 2. Replace the circuit board.
◆ Battery Replacement temperature
disconnected after evacuation. normal after the heatsink temperature falls
The ARD exits the
below 82°C.
3. The following features are available when the ARD and the controller Precautions emergency running Check the wiring and check Product Warranty Card
are in CAN communication: Judgment during discharging: state suddenly a Output abnormality or that the elevator controller
Turn off the ARD and disconnect it from the mains power. 4
When the battery voltage reduces to below 28 short time after it overcurrent exists. power matches the ARD
Take off your metal objects such as ring and watch. Add. of unit:
●
●After evacuation, the controller receives evacuation completion signal Use a screwdriver with insulated handle, and do not lay tools or VDC, and the ARD implements undervotage enters this state or power.
Battery
through CAN communication and terminates evacuation. CAUTION protection and stops output. during operation.
other metals on the battery. undervoltage Customer
NEVER short or reverse the positive and negative poles of the When the AC power input restores to normal, Name of unit: Contact person:
1. Turn K5 or K4 to ON information
●
●When the controller reports errors that require power cutoff, neither the ARD restores to normal power supply state 1. The switch K5 or K4 is
battery. The ARD cannot position, or replace the
normal or emergency power supply is allowed. When the controller and charges the battery.
5 enter the emergency
in OFF state or damaged.
damaged one. P.C.: Tel.:
reports errors, K1, K2, and K4 are disconnected, but not K3. The fault 2. The battery voltage is
Loosen the two captive fasteners on the bottom cover of the MCB; pull Judgment at startup: running state. 2. Charge the battery or
code gives indication. low.
the fasteners to lift the cover along with the hinge to a proper position, When the fault indicator is ON, check whether replace it with a new one. Product model:
and fix the cover by using the latch in the hinge. the air switch K5 and rocker switch K4 are in
●
●Fault reset; receiving reset mark; ARD function fault reset.
closed state.
Body barcode (Attach here):
●
●Binding the manufacturer's code. Battery If the fault persists when both the switches are Product information
overdischarge closed, it indicates the battery is overdischarged
●
●Binding the contract number. Captive or switch not (voltage lower than 27 V). To solve this, the Name of agent:
fastener closed forced charging circuit charges the battery for
●
●The ARD version number is availabe on the main control board in the 4 hours and power-on and -off are performed
control cabinet. again. If the fault is eliminated, the battery is (Maintenance time and content):
still serviceable; if the fault persists after the
4. 220 VAC power supply procedure is repeated several times, you need Failure information
When the mains power is normal, power supply is not controlled by to replace the battery.
software. The ARD cannot provide emergency running at
power failure when there is a warning indicating
When the mains power is faulty: the voltage is low. In case of mains power
failure, the detected battery voltage is below 38
If the DIP switch is set to 220 V, the ARD outputs 220 VAC (with the neu-
V.
tral line). Captive
When the AC power input restores to normal,
fastener Battery voltage
If the DIP switch is set to 380 V, the ARD doest not output 220 VAC (with the ARD restores to normal power supply state
being low
and charges the battery, and this warning is Maintenance personnel:
the neutral line).
reset.
5. Disabling emergency evacuation by manually cut off the mains power If there is still no input from the mains power
within 3 minutes or the voltage is below 28 V,
●
●Connect the NC contact of the main air switch to DI3. K3 is opened and the ARD automatically stops
the battery voltage indication.
●
●Open the main air switch to disable emergency evacuation.
Judgement druing discharging:
In case of 1-minute 1 kW overload or 10-second
Install the new battery as follows: 1.5 kW overload, when the AC power input
restores to normal, the ARD restores to normal
Put a new battery into the battery box.
Output power supply state and charges the battery, and Inovance Technology
Attach the batter cover, and fasten the screws. overload this warning is reset.
protection Auto-resetting is allowed. If there is still no input Address: No.16, Youxiang Road, Yuexi Town, Wuzhong District, Suzhou
Remove the latch, place the bottom cover the MCB well, and fasten the from the mains power within 2 minutes, or ARD 215104, P.R. China
captive screws. voltage is below 28 V, the ARD automatically
stops the battery voltage indication by opening Website: www.inovance.cn
Attach the front cover, and fasten the four screws.
K3.