Professional Documents
Culture Documents
My Courses: Dashboard Basic Engineering Mechanics (ME11003) Tests Test 3
My Courses: Dashboard Basic Engineering Mechanics (ME11003) Tests Test 3
My Courses: Dashboard Basic Engineering Mechanics (ME11003) Tests Test 3
Two wooden planks are joint by using interlocking geometry as shown in the figure. The length dimensions are as below
a = 9.7 mm
c = 5.9 mm
d = 2.7 mm
thickness , t = 2.4 mm
It is known that the wood fails due to shear and the shear strength is 97.279 MPa, what is the maximum value of load P (in N) correct up
to two places in decimal, if the factor of safety is 9.1?
Time estimated: 6-8 minutes
Answer: 1990.91
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 1/8
13/03/2021 Test 3: Attempt review
Question 2
Incorrect
Mark 0.00 out of 12.00
Consider the shear spring shown below. It is made by bonding the rubber annulus to a rigid fixed ring and a plug. When an axial load P =
113.1 kN is placed on the plug, the deflection of the rubber annulus as shown in the dashed lines. Assuming small angles, compute δ (in
m), the magnitude of the deflection at the intersection of the ring and the plug. Take G = 0.0006 GPa, h = 0.30m, r0 = 0.50m and ri =
0.25m. Write correctly up to 4 decimal places
Estimated time: 12-15 minutes
Answer: 0.1000
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 2/8
13/03/2021 Test 3: Attempt review
Question 3
Correct
Mark 12.00 out of 12.00
Consider a multi-material circular shaft as shown in figure, different colors indicate different materials.
d1 = 7.1 mm
L4 = 466.5 N
d2 = 2.93 mm
d4 = 11.5 mm
Which of the following statements is true? Each correct answer is 4 marks and each incorrect answer is -4 makrs
Estimated time 10-12 minutes
a. The stress in section BC is the same as section CD, but strain is not
b. The strain in the member BC is the same as section CD, but stress is not
c. The stress in member BC is = 69.19MPa
The correct answers are: The stress in section BC is the same as section CD, but strain is not, The stress in member BC is = 69.19MPa, If
the value of L1 =-466.50, the section AB is stress free, The ratio of stresses in BC and DE is =15.40
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 3/8
13/03/2021 Test 3: Attempt review
Question 4
Correct
Mark 10.00 out of 10.00
Two aluminum bars (Modulus of elasticity EAl = 72 GPa) are attached to a rigid support at the left and a rigid cross-bar at the right. An
iron bar (EFe = 207 GPa) is attached to the rigid support at the left, and there is a gap b = 2 mm between the right end of the iron bar and
the cross-bar. The cross-sectional area of each bar is A = 100 mm2 and L = 1.2 m. If the iron bar is stretched until it contacts the cross-
bar and welded to it, what is the normal stress (in MPa, correct up to one decimal place) in the iron bar afterward?
Estimated time 10-12 min
Answer: 141.6
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 4/8
13/03/2021 Test 3: Attempt review
Question 5
Correct
Mark 10.00 out of 10.00
Calculate the shear stress in the pin B and the bearing stress at L-shaped link B if the applied load, P is 7.8kN and the diameter of the pin
is 8.9 mm and thickness of member BE is 18 mm
Estimated time: 8-10 minutes
The correct answers are: Shear stress = 0.16 MPa, Bearing stress = 0.06 MPa
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 5/8
13/03/2021 Test 3: Attempt review
Question 6
Incorrect
Mark 0.00 out of 12.00
Three wires are used to suspend the plate shown below. Aluminum wires are used at A and B with a diameter of 2 mm and a steel wire is
used at C with a diameter of 4 mm. Knowing that the allowable stress for Aluminum (Ea=70 GPa) is 150 MPa and that the allowable
stress for steel (Es=210 GPa) is 231 MPa, determine the maximum load P (in N) that can be applied.
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 6/8
13/03/2021 Test 3: Attempt review
Question 7
Correct
Mark 8.00 out of 8.00
The rod is subjected to an axial strain defined by: ϵ = xe-x*x If the length, L=1.5 m, the change in length (in m) of the rod is (write
correctly up to three decimal places):
Estimated time: 8-10 minutes
Answer: 0.447
Question 8
Correct
Mark 8.00 out of 8.00
Consider the figure shown below. If the elastic modulus, E = 202.9 GPa and the cross-sectional area = 4.3 mm2 then the displacement at
the end D in mm is? Write correctly up to three decimal places.
◀ Compensatory/Improvement Test
Jump to...
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 7/8
13/03/2021 Test 3: Attempt review
Compensatory Test ▶
kgpmoodlenew.iitkgp.ac.in/moodle/mod/quiz/review.php?attempt=47507&cmid=532 8/8