Professional Documents
Culture Documents
DEXT 085 DIN 928 Porca Solda Quadrada
DEXT 085 DIN 928 Porca Solda Quadrada
DEXT 085 DIN 928 Porca Solda Quadrada
DIN 928
D
QUELLE: NOLIS (Norm vor Anwendung auf Aktualität prüfen!/Check standard for current issue prior to usage)
ICS 21.060.20 Supersedes
DIN 928:2013-05
Vierkant-Schweißmuttern,
Englische Übersetzung von DIN 928:2013-12
Écrous carrés à souder,
Traduction anglaise de DIN 928:2013-12
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original shall be considered authoritative.
Contents
Page
Foreword ......................................................................................................................................................... 3
1 Scope ................................................................................................................................................. 4
2 Normative references ....................................................................................................................... 4
3 Dimensions ........................................................................................................................................ 5
4 Technical delivery conditions ......................................................................................................... 7
5 Designation ....................................................................................................................................... 8
6 Marking .............................................................................................................................................. 8
7 Representation in drawings............................................................................................................. 8
8 Connecting dimensions ................................................................................................................... 8
Bibliography ................................................................................................................................................. 10
2
DIN 928:2013-12
Foreword
This standard has been prepared by Working Committee NA 067-00-03 AA Verbindungselemente mit
metrischem Innengewinde of the Normenausschuss Mechanische Verbindungselemente (Fasteners Stand-
ards Committee).
The DIN 928:1970-05 edition assigned the property class 8 to square weld nuts, adding “weldable”. Since
then, proof loads for nuts have been increased and new nut heights specified in international (and European)
specifications (see also DIN EN ISO 898-2).
Neither in this nor in the previous revision of this standard did it seem advisable to increase the height of weld
nuts by harmonizing it with the calculation basis for nuts with full loadability, since weld nut mounting is largely
automated. Changing nut dimensions would have caused major difficulties which would not have been
outweighed by a slightly higher resistance to stripping.
Therefore, this latest edition of this standard leaves nut dimensions unchanged, without specifying any
property class. Instead, it only specifies steel with a maximum carbon content of 0,25 % and relevant proof
loads. The proof loads of weld nuts specified in this standard are deemed sufficient to form fully loadable
connections with bolts of a property class < 8.8. Weld nuts with a higher loadability are specified in
DIN EN ISO 21670.
The DIN 4000-161-5 tabular layout of product properties applies to weld nuts covered by this standard.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. DIN shall not be held responsible for identifying any or all such patent rights.
Amendments
e) in Table 1, the value of m has been corrected for M14 and M14 × 1,5;
f) Table 2 replaces 4.1 to 4.3, 4.5 and 4.6;
g) the standard has been revised in form and content.
a) In Table 1, dimension e in the last line (M16) has been corrected from 23 mm to 32 mm.
Previous editions
3
DIN 928:2013-12
1 Scope
This document specifies requirements for square weld nuts with coarse metric threads from sizes M4 to M16
and with fine pitch metric threads from 8 mm to 16 mm in product grade A.
According to DIN EN ISO 898-1, weld nuts specified in this standard are suitable for connection with bolts of
property class < 8.8.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
DIN 13-1, ISO general purpose metric screw threads — Part 1: Nominal sizes for coarse pitch threads —
Nominal diameter from 1 mm to 68 mm
DIN 13-5, ISO general purpose metric screw threads — Part 5: Nominal sizes for 1 mm and 1,25 mm fine
pitch threads — Nominal diameter from 7,5 mm to 200 mm
DIN 13-6, ISO general purpose metric screw threads — Part 6: Nominal sizes for 1,5 mm fine pitch threads —
Nominal diameter from 12 mm to 300 mm
DIN 267-2, Fasteners — Technical delivery conditions — Design and dimensional accuracy
DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts,
screws and studs with specified property classes — Coarse thread and fine pitch thread
DIN EN ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts
with specified property classes — Coarse thread and fine pitch thread
DIN EN ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B
and C
DIN ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
DIN ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ASME B 1.1, Unified Inch Screw Threads (UN and UNR Thread Form) 1)
1 ) Obtainable from Beuth Verlag GmbH (Foreign Standards Service), 10772 Berlin, Germany.
4
DIN 928:2013-12
3 Dimensions
Square weld nuts do not need to be designed as shown in Figure 1, however, their dimensions shall be as
specified in Table 1.
Dimensions in millimetres
5
DIN 928:2013-12
Table 1 — Dimensions
Dimensions in millimetres
Thread size B d1 d2 d3 e h1
D D × Pa Limit
devia- H13 max. min. min. ±0,1
tions
M4 – – 0,80 5,00 4,20 6,40 9 0,60
M5 – – 1,00 6,00 5,25 8,20 12 0,80
±0,15
M6 – – 1,20 7,50 6,30 9,10 13 0,80
M8 M8 × 1 – 1,50 10,00 8,40 12,80 18 1,00
M10 M10 × 1,25 M10 × 1 1,80 12,50 10,50 15,60 22 1,20
– – 7/16-20 UNF-2Bb 1,80 12,50 11,70 15,60 22 1,20
– – 7/16-20 UNF-2Bb 2,00 13,50 11,70 17,40 25 1,40
±0,20
M12 M12 × 1,25 M12 × 1,5 2,00 13,50 12,60 17,40 25 1,40
(M14) (M14 × 1,5) – 2,50 16,80 14,70 20,40 28 1,40
(M16) (M16 × 1,5) – 2,50 18,80 16,80 22,40 32 1,60
6
DIN 928:2013-12
If the proof load test is carried out according to DIN EN ISO 898-2, the loads given in Table 3 apply. In case of
dispute, welding projections shall be removed prior to testing.
7
DIN 928:2013-12
5 Designation
Designation of an M10 square weld nut, made of steel (St):
For square weld nuts with UNF thread the relevant width across flats is to be added to the designation.
Designation of a square weld nut with 7/16-20 UNF-2B thread, with a width across flats of 17 mm (SW17),
made of steel (St):
6 Marking
Square weld nuts of thread sizes M5 and above are to be marked with the manufacturer’s symbol by
indenture to a spot at the discretion of the manufacturer.
7 Representation in drawings
See Table 2.
8 Connecting dimensions
8
DIN 928:2013-12
Dimensions in millimetres
Thread size as in Table 1 Sheet thickness a Hole diameter d4a
9
DIN 928:2013-12
Bibliography
DIN 4000-161, Tabular layout of product properties — Part 161: Fasteners with internal thread
10