Professional Documents
Culture Documents
TC544 244 344
TC544 244 344
Features :
! 4+4 Digits, 7 Segment LED Dual Display
! TC / RTD Input
! ON - OFF / PID Control
! Two Set Points
o
! C / oF Selectable
! Field selectable Control Output (Relay or SSR)
! Auxiliary Output : Relay / SSR
48 x 48 mm 72 x 72 mm 96 x 96mm ®
Certifications : C US
Digits 4+4 Digits, 7 Segment LED Dual Display Control Action 1) PID Control with auto tuning.
LED Indication 1. Output 1 ON T : Auto tune 2) ON - OFF Control
2. Output 2 ON S : Dwell timer Proportional Band (P) 1.0 to 400.0o
Integral Time (I) 0 to 9999 sec
Derivative Time (D) 0 to 9999 sec
Input Specifications
Cycle Time 0.1 to 99.9 sec
Inputs Thermocouple (J, K, T, R, S) / RTD (PT100) Hysteresis Width 0.1 to 99.9o
Resolution 0.1 / 1o for TC / RTD inputs Manual Reset Value -19.9 to 19.9o
(fixed 1o for R & S type TC input)
Heat-cool
Indication Accuracy For J, K & T inputs : 0.25% of F.S. ±1o
Control Action PID
For R & S inputs : 0.5% of F.S. ±2o
(20 min of warm up time for TC inputs) Proportional Band - Cool 0.0 to 400.0o
For RTD input : 0.1% of F.S. ±1o Cycle Time-Cool 0.1 to 99.9 sec
(F.S. = Full Scale)
o
Dead Band Programmable from setpoint low limit
Temperature Unit C / oF selectable to setpoint high limit.
Input Filter (FTC) 0.2 to 10.0 sec Settings for Alarm Output
Sampling time 250 ms Modes Deviation, Absolute
Hysteresis 0.1 to 99.9o
Output Specifications
Dimensions
Panel Cutout
B D F
A E G
C
www.selec.com 1
TC544A / TC244AX / TC344AX Temperature Controllers
TC544A-CU
®
-- --
All dimensions are in mm C US
TC544A-24V -- --
SSR1+
N (-) 2 9
TC-/RTD2
N (-) 2 11
TC-/RTD2 Accessories (Optional)
N( ) 2 7 - NO2 + 3 12
TC /RTD2 3 10 RTD3
Standard SELEC accessories that can be used with this product.
- SSR2
NO2
NO2 RTD3 +
SSR2
4 13
3 + 8 COM2 4 11
- SSR2
RTD3 COM2
Adapter plate
-
5 14
NC2 5 12 +
NC2 6 15
SSR
4 9
COM2 SSR1- NO1
6 13
NO1
7 16 +
1) AP7248 : Plastic adapter plate, used to mount 1 / 16 DIN (cutout size 48 x 48)
-
SSR1
NO1
5 12 10 COM1 7 14 COM1 8 17 Instrument into existing (72 x 72) cutout size.
-
COM1 NC1
NC1 9 18
2) AP9648 : Plastic adapter plate, used to mount 1 / 16 DIN (cutout size 48 x 48)
Instrument into existing (96 x 96) cutout size.
Cable Size (AWG) : 16-13 ; Stud Hole for Lug (inch) : 0.137 ; Tightening Torque (Lb-inch) : 7 3) AP9672 : Plastic adapter plate, used to mount 72 x 72mm size instrument
Cable Size (mm2) : 1.5-2.5 ; Stud Hole for Lug (mm) : 3.5 ; Tightening Torque (N-m) : 0.8 into existing (96 x 96) cutout size.
4) AP4896-4848-G-C : Plastic adapter plate, used to mount 1 / 16 DIN
(cutout size 48 x 48) Instrument into existing (48 x 96)
Compliance cutout size.
Applicable EMI / EMC Standards
Product Standard : IEC 61326-1 Mounting Accessories (Supplied with units)
Category Standards Compliance
For TC544 : 48 X 48 Collar clamp ACL4802
ESD Immunity IEC 61000-4-2 Level III For TC244/TC344 : Clamp side with screw assembled
www.selec.com 2