‘Component Interfaces (Successful Handover)
LTE Mobile “eNodeB Network
20-Apr1322.05 (Page 1)
Dero
el
leNodeBs in LTE are interconnected with the X2 interface. If two eNodeBs are served by the same MME, handover from the
[source to the target eNodeB will take place over the X2 interface,
[Before the handover
SOE esr
The UE and Source eNodeB are in RRC
Connected state.
[Downlink Gta flow before handover
Downlink data is flowing from the SGW to the UE via the Sour
Execs)
Downlink Data
Downlink Data
[Uplink data flow before handover
Uplink data is flowing from the UE to the SGW via the Source
Uplink Data
Uplink Data
[Handover pipparation
RC Measurement Contr The network sets the measurement thresholds for
|sending measurement reports.
Neighboring cell signal quality is now better than
the serving cell
‘Sihalshengn otras
link S1 Bearer Establishment ISTP connect for the uplink side is established
lbetween the Target eNodeB and the serving SGW.
[Handover execution
RRC Cepmecton Reconfiguration Request ne Source eNode8 sends a handover command
an io to UE, The meseage contain a new C-RNTI
and now DRS IDs, ARAGH preanbl le seo
‘grant rt ude for eonvenion ree RACH access
FE sel
[Downlink data flow duting handover preparation)
[At this point all downlink data is getting rerouted from the
See eee ae)
ieee Aa aren cn
een
Downlink Data‘Component Interfaces (Successful Handover)
LTE Mobile ‘eNodeB Network
Core Network
20-Apr-13.22.05 (Page 2)
jplink data flow during handover preparation
The uplink data is still being
beter eras
Uplink Data
USS)
Uplink Data
== __ ===
[Synchronizipg with target cal
RACH Preamble
ta Access Respons|
RRC Copnection Reconfiguration fomplete
La |
remission of queued dowpiink data
Downlink Data
Downlink Data
Downlink Data
Serer oe wy
Pecan kee eas
jownlink data flow during handover dxecution
Downlink Data
Downlink Data
ary
[Uplink data flow during handover exepution
Uplink Data
IUE uses the preamble assigned in the handover
|command to send a RACH to the target eNodeB,
[The target eNodeB accepts the request and
responds back with a timing adjustment and an
luplink resource grant.
The UE uses the assigned resources to transmit
the Handover Confirm message (RRC Connection
Reconfiguration Complete).‘Component Interfaces (Successful Handover)
ached Has, |
tages
[Send end marker
PS r urns
Pee ee mcg
Cees thao ere?
Coico kaeerea cs)
Deters
End Marker
=z =m
vards the
Chey
Jownlink dpta flow after handover
oe soe NUL RAST)
Downlink Data
Downlink Data
SAA Path Switch Request Ack
LTE Mobile ‘eNodeB Network Core Network 20-Apr-13.22.05 (Page 3)
jandover cmpletion
[Switching pth
[At this point, the UE is receiving and transmitting data. The downlink
data transmission towards the terminal is stil being routed via the
Carma ace try
Xecuter
JAP Path Switch Requegt The target eNodeB requests the MME to switch
a the path from the source eNodeB to the target
JeNodeB. (Click on the message name above the
Jarrow to see message details)
ISGW is now sending the data using the target
JeNodeB TEID.
IMME responds back to signal the completion of
the path swiitch. (Click on the message name
Jabove the arrow to see message details)