Professional Documents
Culture Documents
Asl 1000
Asl 1000
Keyboard,
Mouse,Monitor
ASL1000 P3 PC 正面
RESET
HD、電源
指示燈
52XCD-ROM
電源開關
USB,NT4.0
不支援
2.5吋軟碟機 硬碟抽取盒(內有40G硬碟)
ASL1000 P3 PC 背面
D-Sub monitor
DMM Com2
Printer port
Network
AC Input
110V~220
VAC
RESET
HD、電源
指示燈
52XCD-R
Keyboard
lock
電源開關
2.5吋軟碟機
硬碟抽取盒(內有80G硬碟)
ASL1000 P4 PC 背面
D-Sub monitor
DMM Com2
Printer port
Network
AC Input
110V~220
VAC
總電源開關 Keyboard
Mouse
DB25 TTL BUS
DB37 TTL BUS
HP34401A 正面
電源開關 校驗日期標籤
量測前端輸入
量測前端後端選取開關
Power supply Test head Power cord
Interconnect
board
拆 load board 用的
Instrument DVI300mA
Part number:
950025-03
671-4678-xx
Part number:
671-4676-xx
Part number:
950013-01
-03
-05
671-5351-00
MUX-LV 500 V
MUX-LV 1 A
Instrument MUX-HV
Part number:
950013-02
-04
-06
671-4682-00
MUX-HV 200 V
MUX-HV 1.5 A
Instrument OVI30mA
Part number:
950033-XX
671-3032-XX
Part number:
671-7096-XX
671-4681-XX
Part number:
671-5361-XX
Part number:
950012-XX
671-5333-XX
Instrument DDD 128 master
Part number:
671-5334-00
Part number:
950006-04
Op Amp/Comparator Functions
I bias Ranges from 10nA to 10μA Full Scale
VIO Ranges from 100μV to 100mV Full Scale
Instrument LCB
Part number:
950022-XX
671-7026-00
Instrument SCB
Part number:
950148-XX
671-5355-00
Instrument backplane 正面
Part number:
950008-01
Slot 編號
Instrument backplane 背面
TTL signal
BUS
P13 P12
插 Interconnector
board 的地方
Instrument Power sequencer
Part number:
671-3031-XX
當短路或是有過大的逆電流時,此
片 PCB 會保護 test head 裡的板子
,避免燒毀。
Instrument HVS
Part number:
671-4666-00
Part number:
671-3030-01
Part number:
671-3030-01
Part number:
671-4666-00
請務必確認
CAL DUT
Config 100%
吻合系統上的
Hardware
配置!!
目前 VATE 的
版本
請點選 cancel 圖示
DC calibration step 6
Act 顯示錯亂通常為:
1. 50Pin TTL cable(power cord) 問題
2. I/F card pull contact 或壞掉
3. VATE 損毀
Troubleshooting (3)
解決上面所出現的問題可做以下的動作:
1. 刪除 C:\asl_nt\system\config\defaults.mtn
2. 刪除 C:\asl_nt\system\config\*.tmp
3. 刪除 D:\temp\*.*
4. 請不要刪
C:\asl_nt\system\config\defaults.db
檔案一旦刪除, VATE 會損毀,需重新安裝
Troubleshooting (5)
解決步驟:
Step 1. 檢查 CAL DUT 是否 pull contact
Step 2. 檢查 meter, BNC cable, 確認 FORCE 和 SENCE 沒有接反
Step 3. 檢查 Interconnect board
各位大大~~這是我們新進的ASL1000
它與我們以前舊型的ASL多了1個開關
This is the new tester machine.
此開關是控制前面SCB的電源開關
This switch is controls scb the power source
This is scb.
在安裝load board or CAL board前 Before Set up load board or CAL board,
請先關閉此開關 Please first this switch close
請務必將開關關閉 再裝上loadboard 或
CAL board 以防止板子燒壞
Please closure power source.