I. IDENTIFICATION: Determine what is asked. Write your answer on your TEST III. IDENTIFICATION: Determine what is asked. Write your answer on your TEST booklet booklet 1. This factor allows for the fact that effective candle power of all lamps or 1. This factor allows for the fact that effective candle power of all lamps or luminous sources deteriorates owing to blackening and /or accumulation of luminous sources deteriorates owing to blackening and /or accumulation of dust or dirt on globes and reflectors etc. dust or dirt on globes and reflectors etc. 2. Phenomena where radiation at a specific wavelength is absorbed, usually by a 2. Phenomena where radiation at a specific wavelength is absorbed, usually by a solid, then re-emitted at different wavelength. solid, then re-emitted at different wavelength. 3. Type of reflection that occurs when an uneven surface reflects light at more 3. Type of reflection that occurs when an uneven surface reflects light at more than one angle, but the reflected angles are all more or less the same as the than one angle, but the reflected angles are all more or less the same as the incident angle. incident angle. 4. 4. 5. Factors that may affect light transmission on a medium 5. Factors that may affect light transmission on a medium 6. 6. 7. States that illuminance is directly proportional to the cosine of the angle made 7. States that illuminance is directly proportional to the cosine of the angle made by the normal to the illuminated surface with the direction if the incident flux by the normal to the illuminated surface with the direction if the incident flux 8. The absolute temperature(in degree Kelvin) of a blackbody radiator whose 8. The absolute temperature(in degree Kelvin) of a blackbody radiator whose chromaticity merely resembles that of a light source. chromaticity merely resembles that of a light source. 9. It is the method of producing artificial light by applying heat or raising the 9. It is the method of producing artificial light by applying heat or raising the temperature of a solid body or vapour. temperature of a solid body or vapour. 10. Luminaire in this class are electrically insulated and provided with a connection 10. Luminaire in this class are electrically insulated and provided with a connection to earth. Exposed metal parts that could become live in the event of basic to earth. Exposed metal parts that could become live in the event of basic insulation failure are protected by earthing. insulation failure are protected by earthing. II. PROBLEM SOLVING: Present a clear and orderly handwritten solution for the IV. PROBLEM SOLVING: Present a clear and orderly handwritten solution for the problems below. Compute up to 3 decimal places. SHOW ALL THE STEPS IN problems below. Compute up to 3 decimal places. SHOW ALL THE STEPS IN THE SOLUTION. No shortcuts allowed. Avoid erasures. Box all final answers. THE SOLUTION. No shortcuts allowed. Avoid erasures. Box all final answers. Unboxed final answers will not be considered. Unboxed final answers will not be considered. 1. A light source having an intensity of 500 candle in all directions is fitted with a 1. A light source having an intensity of 500 candle in all directions is fitted with a reflector so that it directs 80% of its light along a beam having a divergence of reflector so that it directs 80% of its light along a beam having a divergence of 150. what is the total light flux emitted along the beam? What will be the 150. what is the total light flux emitted along the beam? What will be the average illumination produced on a surface normal to the beam direction at a average illumination produced on a surface normal to the beam direction at a distance of 10m? distance of 10m? 2. A room 40 m X 15 m is to be illuminated by 1.5 m 80—W fluorescent tubes 2. A room 40 m X 15 m is to be illuminated by 1.5 m 80—W fluorescent tubes mounted 3.5 m above the working plane on which an average illumination of mounted 3.5 m above the working plane on which an average illumination of 1801m/m2 is required. Using maintenance factor of 0.8 and the utilization 1801m/m2 is required. Using maintenance factor of 0.8 and the utilization factor of 0.5, design and sketch a suitable layout. The 80—W fluorescent tube factor of 0.5, design and sketch a suitable layout. The 80—W fluorescent tube has an output of 4,500 1m. has an output of 4,500 1m.