Professional Documents
Culture Documents
Service Manual Pioneer DDJ SR
Service Manual Pioneer DDJ SR
RRV4499
DDJ-SR
DJ Controller
DDJ-SR
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
CONTENTS
C SAFETY INFORMATION..........................................................................................................................................................2
1. SERVICE PRECAUTIONS ....................................................................................................................................................3
1.1 NOTES ON SOLDERING ...............................................................................................................................................3
1.2 NOTES ON PARTS REPLACEMENT .............................................................................................................................3
1.3 ABOUT DEMO MODE ....................................................................................................................................................4
2. SPECIFICATIONS .................................................................................................................................................................5
3. BASIC ITEMS FOR SERVICE...............................................................................................................................................6
3.1 CHECK POINTS AFTER SERVICING............................................................................................................................6
3.2 JIGS LIST .......................................................................................................................................................................6
3.3 PCB LOCATIONS ...........................................................................................................................................................7
4. BLOCK DIAGRAM.................................................................................................................................................................8
4.1 OVERALL WIRING DIAGRAM........................................................................................................................................8
D 4.2 OVERALL BLOCK DIAGRAM.......................................................................................................................................10
5. DIAGNOSIS.........................................................................................................................................................................12
5.1 TROUBLESHOOTING ..................................................................................................................................................12
5.2 BASIC OPERATION CHECK USING SERATO DJ .......................................................................................................14
6. SERVICE MODE .................................................................................................................................................................17
6.1 SERVICE MODE...........................................................................................................................................................17
7. DISASSEMBLY....................................................................................................................................................................27
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................33
8.1 NECESSARY ITEMS TO BE NOTED ...........................................................................................................................33
8.2 UPDATING OF THE FIRMWARE .................................................................................................................................33
8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE ...........................................................................................35
9. EXPLODED VIEWS AND PARTS LIST...............................................................................................................................38
E
9.1 PACKING SECTION .....................................................................................................................................................38
9.2 EXTERIOR SECTION...................................................................................................................................................40
10. SCHEMATIC DIAGRAM ....................................................................................................................................................44
10.1 MIC and HEADPHONE PCB ASSYS .........................................................................................................................44
10.2 I/O PCB ASSY ............................................................................................................................................................46
10.3 MIXER and CROSS FADER PCB ASSYS..................................................................................................................48
10.4 PANEL-L and R PCB ASSYS......................................................................................................................................50
10.5 WAVEFORMS .............................................................................................................................................................52
11. PCB CONNECTION DIAGRAM ........................................................................................................................................56
11.1 MIC and HEADPHONE PCB ASSYS .........................................................................................................................56
11.2 I/O PCB ASSY ............................................................................................................................................................58
F 11.3 MIXER and CROSS FADER PCB ASSYS..................................................................................................................60
11.4 PANEL-L and R PCB ASSYS......................................................................................................................................62
12. PCB PARTS LIST ..............................................................................................................................................................64
2 DDJ-SR
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. A
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
B
temperatures (hard to melt/easy to harden).
Notes:
• Do not reuse the double-back tape.
• Put the double-back tape on the Chassis Assy side. NITTO No. 500
(5 mm × 30 mm)
DDJ-SR 3
5 6 7 8
1 2 3 4
4 DDJ-SR
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
General – Main Unit Accessories A
Power supply........................................................................ DC 5 V
Rated current....................................................................... 500 mA • CD-ROM (Installation Disc)
Main unit weight..........................................................4.5 kg (9.9 lb)
Max. dimensions......553.6 mm (W) × 65.3 mm (H) × 319.1 mm (D) • USB cable
(21.8 in. (W) × 2.6 in. (H) × 12.6 in. (D)) (408-SUB-132)
Tolerable operating temperature..............................+5 °C to +35 °C
Tolerable operating humidity............5 % to 85 % (no condensation) • Read Before Use (Important)/Quick Start Guide
(DDJ-SR/CKSUVYXE5: 502-DDJSRA-3325A, 502-DDJSRA-3326A)
Audio Section (DDJ-SR/XECN5: 502-DDJSRB-3327)
Rated output level
MASTER OUT 1 ............................................................. 4.2 Vrms • Warranty (for some regions)
MASTER OUT 2 ............................................................. 2.1 Vrms The included warranty is for the European region.
BOOTH........................................................................... 2.1 Vrms • For the North American region, the corresponding information is B
Total harmonic distortion provided on the last page of both the English and French
MASTER OUT..................................................................0.006 % versions of the “Read Before Use (Important)/Quick Start Guide”.
Frequency characteristic • For the Japanese region, the corresponding information is
USB, AUX, MIC ................................................... 20 Hz to 20 kHz provided on the last page of the Japanese version of the “Read
S/N ratio (when playing on computer) Before Use (Important)/Quick Start Guide”.
MASTER OUT................................................................... 101 dB
Input impedance
AUX ..................................................................................... 47 kΩ
MIC...................................................................................... 10 kΩ
Output impedance
MASTER OUT....................................................................... 1 kΩ
PHONES ............................................................................... 32 Ω
USB AUDIO.................................................... 24 bit/Fs : 44.1 kHz
C
Input / Output terminals
AUX IN input terminal
RCA pin jacks ........................................................................ 1 set
MIC terminal
Phone jack (Ø 6.3 mm).......................................................... 1 set
BOOTH OUT/MASTER OUT2 output terminal
RCA pin jacks ........................................................................ 1 set
MASTER OUT1 output terminal
Phone jack (Ø 6.3 mm).......................................................... 1 set
PHONES output terminal
Stereo phone jack (Ø 6.3 mm) .............................................. 1 set
Stereo mini phone jack (Ø 3.5 mm)....................................... 1 set
USB terminal D
B type .................................................................................... 1 set
DDJ-SR 5
5 6 7 8
1 2 3 4
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
C Distortion Volume too high
Noise Volume fluctuating
Volume too low Sound interrupted
6 DDJ-SR
1 2 3 4
5 6 7 8
• Bottom view
NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Mark No. Description Part No. Mark No. Description Part No. E
LIST OF ASSEMBLIES
MIC PCB ASSY 704-SR-A601 PANEL-L PCB ASSY 704-SR-A599
HEADPHONE PCB ASSY 704-SR-A600 PANEL-R PCB ASSY 704-SR-A598
I/O PCB ASSY 704-SR-A596
MIXER PCB ASSY 704-SR-A597
CROSS FADER ASSY 704-DJM250-A032
DDJ-SR 7
5 6 7 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A
(704-SR-A596)
W7
B
CN2A CN1A CN3A
G D
MIXER PCB ASSY
PANEL-R PCB ASSY 3 (704-SR-A597) 2 P
(704-SR-A598) 4 (
TO TO
OUTPUT BOARD OUTPUT BOARD
D
CHASSIS CHASSIS
CN2B
CN1B
CN2C
CHASSIS
1
CN6 CN701A CN701B TO
E TO CARBO
CARBON PAD FFC WIRE
CN500 W700
CN01
8 DDJ-SR
1 2 3 4
5 6 7 8
CN2C CN3A
D3.3V D3.3V
1 1
D5V D5V
2 2
AD3.3V AD3.3V
3 3
AD6b AD7b
4 4
AD8 AD13
5 5
AD9 AD14
6 6
AD12 AD15
7 7
ADGND ADGND
8 8
K EY1
9 9
K EY1 C
K EY2 K EY2
10 10
K EY3 K EY3
11 11
K EY4 K EY4
12 12
K EY5 K EY5
F G
LED1
LED2
LED3
13
14
15
16
13
14
15
16
LED1
LED2
LED3 C
PANEL-L PCB ASSY PANEL-R
LED4
LED5
17
18 3 17
18
LED4
LED5 I/O
4 (704-SR-A599) PCB ASSY
LED6
LED7
19
20
19
20
LED6
LED7 PCB ASSY
LED8 LED8
21 21
S1 S10
22 22
S2 S11
23 23
S3 S12
24 24
S4 S13
25 25
S5 S14
26 26
S6 S15
27 27
A A
28 28
B B
29 29
C C
30 30
WL -A
31 31
WR- A D
WL -B WR- B
32 32
LED- G LED- G
33 33
DGND DGND
34 34
CN2B
CN2A CN2B
D3.3V D3.3V
1 1
D5V D5V
2 2
AD3.3V AD3.3V
3 3
AD6b (AD7b) AD6b
4 4
AD8 (AD13) AD8
5 5
CHASSIS AD9
6 6
(AD14) AD9
AD12 (AD15) AD12
7 7
ADGND ADGND
8 8
K EY1 K EY1
9 9
K EY2 K EY2
10 10
K EY3 K EY3
11 11
K EY4 K EY4
12 12
CN701B TO K EY5
13 13
K EY5
LED1 LED1
CARBON PAD FFC WIRE CN7 LED2
14 14
LED2 E
C LED3
15
16
15
16
LED3 F
LED4 LED4
CN500
I/O LED5
17
18
4 17
18
LED5 PANEL-L
LED6 LED6
PCB ASSY LED7
19
20
19
20
LED7 PCB ASSY
LED8 LED8
21 21
S1 S1
22 22
S2 S2
23 23
S3 S3
24 24
S4 S4
25 25
S5 S5
26 26
S6 S6
27 27
A A
28 28
DDJ-SR 9
5 6 7 8
1 2 3 4
D M
A C I/O PCB ASSY ROTATE VR * 23
AD * 23
F P
G P
VUSB TEMPO VR * 2
5V D5V IC27 D3.3V D1.2V AD * 4
1 2 TPS54232 IC13
BD12AK5FB
STEP DOWN A3.3V
DA3.3V
-6V
IC10
TPS54232 SLIDER SW * 1 AD * 1
B INVERTER
6V A5V AD5V
IC9
IC11
TPS61085 BA05
BOOST
I2C
50
VUSB X1 6M
D IC16
51
TUSB3200 44
(12MHz or 48MHz)
USB PortB
39 36 38
0dB LEVEL -5.46dB
PCO-0
PCO-1
PCI-0
LRCK
IC22
BCK
AUX 3 IC1 1 3 IC2 1 1 ADC 12
PCM1803
37 64 63
AUX
31
IC15
ADSP-BF592
(44.1K/24bit/512fs for A/D,D
MIC (I2S format for audio data)
E 32
10 DDJ-SR
1 2 3 4
5 6 7 8
AD * 23
F PANEL-L PCB ASSY
G PANEL-R PCB ASSY
ENCODE * 1
I2C1 GPIO * 7
2C SLIDER SW * 1
JOG WHEEL *2
IC19
24LC02BT
EEPROM
IC16 IC18 D
MCLK SCK
TUSB3200 44 3 SCHMITT 2 AD/DA CLK
Hz or 48MHz) SN74LVC1G
38
PCO-1
LRCK
BCK
63 IC4
SPI LPF&.
IC5
IC24 3
L
IC15 MAS 2 MASTER1
36 1 DAC 7 6 7 R
ADSP-BF592 1
CS4344 G
4.1K/24bit/512fs for A/D,D/A) BOOTH
5 NJM4580
2S format for audio data) NJM4580
E
HP
4
61 62 IC6
X2 LPF&.
IC25
1 DAC 7 6 7 BOOTH/MASTER2
24.576M CS4344 (RCA)
NJM4580
IC7
LPF&. B HEADPHONE PCB ASSY
IC26 Headphone
1 DAC 7 2 1
(32 ohm/6.3mm & 3.5mm) F
CS4344
NJM4556
DDJ-SR 11
5 6 7 8
1 2 3 4
5. DIAGNOSIS
5.1 TROUBLESHOOTING
A [0] Service mode [2] Troubles of operation element
Conduct diagonosis on troubles using Service mode. and LED
No Does the MIDI When you pressed on button, No UCOM (IC20) is defective.
command output? is the target KEY signal "H"? Replace the I/O PCB Assy.
Yes
When you turn VR,
No VR is defective.
Does D3.3V become No Power supply IC (IC27) is defective. does the signal from VR
change? Replace the corresponding part.
3.3 V correctly? Replace the I/O PCB Assy.
Yes
Yes
Yes
Yes
UCOM (IC20) is defective.
UCOM (IC20) is defective.
Replace the I/O PCB Assy.
Replace the I/O PCB Assy.
Is the communication line No UCOM (IC16) is defective. Rotary selector does not work.
of the USB "H" or "L"? Replace the I/O PCB Assy.
Yes
Push
Confirm whether there is not the Do not push and rotary See "Buttons or slide SW does
part on the USB line abnormally. which work? not work".
Object: D11 - 14, L13
Rotary
Check on 3 pin, 1 pin of
Is the abnormality in No UCOM (IC16) is defective. the rotary selector. No UCOM (IC20) is defective.
the parts mentioned above? Replace the I/O PCB Assy. When you turned a rotary Replace the I/O PCB Assy.
selector, is the signal H?
F Yes
Yes
12 DDJ-SR
1 2 3 4
5 6 7 8
Pad does not work. [4] Troubles of Jog touch and Jog rotation A
The LED lits by matrix drive. [5] Troubles of sound input and output
C
Sound does not output.
No
Does not all LED lit?
Yes F
DDJ-SR 13
5 6 7 8
1 2 3 4
• For the latest information on the required operating environment and compatibility as well as to acquire the latest operating
system, refer to “Software Info” under “DDJ-SR” on the Pioneer DJ support site below.
http://pioneerdj.com/support/
• Operating System support assumes you are using the latest point release for that version.
C
For the latest version of the Serato DJ software, access Serato.com and download the software from there.
For downloading, registration of a user account at "Serato.com" is required.
Unzip the downloaded file, then double-click the unzipped file to launch the installer.
Read the terms of the license agreement carefully, and if you agree, select [I agree to the license terms and conditions],
then click [Install].
After installation is completed, the Installation Completed screen will be displayed. Click on [Close] to terminate the Serato DJ
installer.
[Connections]
2 5
6 1
[Operating procedures]
1 Connect headphones to one of the [HEADPHONES] terminals.
2 Connect powered speakers, a power amplifier, components, etc., to the [MASTER OUT 1] or
[BOOTH OUT/MASTER OUT 2] terminals.
3 Connect this unit to your computer via a USB cable.
4 Turn on the computer’ s power.
5 Switch the [ON/OFF] switch on this unit’ s rear panel to the [ON] side to turn this unit’ s power on.
F 6 Turn on the power of the devices connected to the output terminals (powered speakers, power amplifier, components, etc.).
14 DDJ-SR
1 2 3 4
5 6 7 8
Launching Serato DJ
From the Windows [Start] menu, click the [Serato DJ] icon under [All Programs] > [Serato] > [Serato DJ].
When Serato DJ is launched after it is installed, a yellow icon saying “BUY/ACTIVATE” might be displayed in the License panel
on the right side of the Serato DJ screen.
DDJ-SR users do not have to activate or buy Serato DJ.
If you tick the check box of [DO NOT SHOW AGAIN] and click [Online], the icon will disappear thereafter.
Importing tracks
B
1 Click the [Files] key on the Serato DJ software screen to open the [Files] panel.
2 Click the folder on the [Files] panel containing the tracks you want to add to the library to select it.
3 On the Serato DJ software screen, drag and drop the selected folder to the crates panel.
a : [Files] panel
a b : Crates panel
a : Library
b : Crates panel
b
E
DDJ-SR 15
5 6 7 8
1 2 3 4
1
2 2
2
3
1 11 7
4
5
3 3
6
7
10
8
B 9
4 4
9 8
2 Press the [f] button to play the track. 5
3 Move the channel fader away from you.
4 Turn the [TRIM] control.
Adjust [TRIM] so that the orange indicator on the
6 6
channel level indicator lights at the peak level.
5 Turn the [MASTER LEVEL] control to adjust the audio
level of the speakers.
10
11
16 DDJ-SR
1 2 3 4
5 6 7 8
6. SERVICE MODE
6.1 SERVICE MODE
[1] Error Alarming A
1 2
into
Service mode
E
Factory Reset
[Method to enter]
Press and hold the left DECK "SHIFT" button and the left "DECK 1" button, then Power-ON.
The firmware version is displayed first. LED except it turn off.
[Method to exit]
Power-OFF
[Note]
When in this mode, the firmware version display appear first. F
In this mode, it does not work to communicate with computer via USB.
In this mode, LED dimmer is not available.
DDJ-SR 17
5 6 7 8
1 2 3 4
2 seconds later
0 1 2 3 4 5 6 7 8 9
D
18 DDJ-SR
1 2 3 4
5 6 7 8
After checking the firmware version, you can check if each UI parts (button/jog dial/knob/fader etc.) are not abnormal.
All UI parts of top&front panel are objects to check.
[Note]
In case of the left parts, the left parts LED are lit.
In case of the right parts, the right parts LED are lit.
In case of the center parts, the right&left parts LED are lit.
All buttons other than the Rotary selector, LED will light only while it is pressed. E
DDJ-SR 19
5 6 7 8
1 2 3 4
••• •••
Volume type
••• •••
D
MIN MAX
MIN
MAX
1 2 3 6 7 8 12 13
••• •••
MIN MAX
F
20 DDJ-SR
1 2 3 4
5 6 7 8
MIN MAX
••• •••
MIN MAX
C
OFF ON
When Rotary selector is rotated clockwise,"LIGHTING COLOR Mode" is changed cyclically as follows.
• • • → 1 → 2 → 3 → 4 → 5 → 1 →• • •
When Rotary selector is rotated counterclockwise,"LIGHTING COLOR Mode" is changed cyclically as follows.
• • • → 5 → 4 → 3 → 2 → 1 → 5 →• • •
When Rotary selectoris rotated, "LED BRIGHTNESS Mode" does not change.
F
*As two LEDs of different colors each are embedded in the LOAD button and the HOT CUE, ROLL, SLICER, and
SAMPLER buttons, LIGHTING COLOR mode can be used for failure diagnosis of each LED.
DDJ-SR 21
5 6 7 8
1 2 3 4
A
3. Factory Reset
The following data is reset to the factory default settings by "Factory reset" operation.
• Setting data in Utility mode
• Last memory of users
[Method to reset]
Press and hold the left DECK "SYNC" button and the right DECK "SYNC" button.
Then factory reset starts and "SYNC"LEDs are lit.
After completing reset, "SYNC" LEDs are turned off.
into
Measurement mode
[Method to enter]
Press and hold the "SHIFT"+"DECK3" buttons then Power-ON.
During this mode, "DECK 3" and "DECK 4" LEDs are lit.
[Method to exit]
F
Power-OFF
22 DDJ-SR
1 2 3 4
5 6 7 8
This is the mode to measure the JOG rotation time which is specified at "Jog dial Performance specification".
The specified range is 100 ± 40 msec.
[Method to measure]
1 You spin Jog dial more than 33*7 = 231 rpm.
*1 In case of less than 231 rpm, it is failure. Then "SLIP" LED (Deck1) is lit.
*2 You must measure by either clockwize or counterclockwize.
3 The controller display result with three Channel level indicators. Refer to below.
The format of the result is "XXX" msec. (X: 0-999 msec .decimal)
It is displayed by the Headphone CUE/TAP buttons (Deck1 / Deck 2) and Level indicator.
Display of the 1st digit Display of the 2nd digit Display of the 3rd digit
D
[Numerics expressed with the number of lit LEDs]
0 1 2 3 4 5 6 7 8 9
E
If the measurement result is outside the specified range, check the amount of grease for the Jog dial and the chassis.
DDJ-SR 23
5 6 7 8
1 2 3 4
[Overview]
Will be tested fluctuation of voltage (A/D conversion value) which is made each Fader and Rotary volume by Level indicator.
6 16
C
1 2 3 4 22 23 24 25
5 26
11 21
D 12
13
7 8 9 10 17 18 19 20
15 14
[Test detail]
1 Choose the test subject by turn left and right Rotary selector.
E The LED is lit with the following turns every 1 click.
Turn right: 1 → 2 → 3 → 4 → . . . . . → 25 → 26 → 1 → . . .
Turn left: 26 → 25 → 24 → . . . . . → 2 → 1 → 26 → . . .
Note: Regarding No.15, both LED are lit.
2 You can see what knob/fader is selected by Lighting LED on each button as shown in the above figure.
For example ,LED to test Channel fader is "Headphone CUE/TAP" button's LED.
3 When targeted knob is decided, push the Rotary selector and start observation of A/D conversion value.
Get the A / D conversion value immediately after the start. It will be reference value.
*A/D conversion value to be monitored is Raw data.
F 4 Start monitoring and later to monitor the A/D conversion value, do the following actions depending on its value with
Master level indicator.
24 DDJ-SR
1 2 3 4
5 6 7 8
A
Result Fig No.
+1 from the reference value A/D conversion value 1
+2 from the reference value A/D conversion value 2
+3 from the reference value A/D conversion value 3
+4 from the reference value A/D conversion value 4
Over +5 From the reference value A/D conversion value 5
-1 from the reference value A/D conversion value 6
-2 from the reference value A/D conversion value 7
-3 from the reference value A/D conversion value 8
-4 from the reference value A/D conversion value 9
Less than -5 from the reference value A/D conversion value 10
* Display at the same time both fall / rise direction from the reference value of the conversion value A/D. B
Level indicator
1 2 3 4 5 6 7 8 9 10
* Keep the lighting position at the time of maximum fluctuation of each of the positive & negative direction
5 By pushing the Rotary selector while monitoring the conversion value A/D, it is possible to reset the state of the fluctuations C
of the past.
Ex.) 7. More time has elapsed, Level indicator is lit as
1. Turn EQ HI knob (for DECK 1) to the position you want to follows: become the value 758 of the A/D.
measure.
DECK1
10. Off all the LED on Level indicator When you push
the Rotary selector, and this value will be new reference
5. More time has elapsed, to maintain the above display value.
762 even though the value of the A/D.
DDJ-SR 25
5 6 7 8
1 2 3 4
A [4] Operation Test of the Velocity Sensitivity and Aftertouch for the Performance pads
Testing the velocity sensitivity and aftertouch of the operating elements shown below.
B [Method to enter]
To enter the mode for testing the velocity sensitivity and aftertouch of the operating elements, after the unit starts in Service
mode, press the Rotary selector over 1 second. Performance pads 1 on both decks are lit and other LEDs are unlit.
[Method to exit]
Power-OFF.
Or, if the Rotary selector is pressed over 1 second again, all of Performance pad on both decks are unlit.
And the unit returns to normal Service mode.
[Operation method]
Press Performance pad or hold Performance pad pressed.
C
D
[Description of the modes]
• Values obtained in response to the speed of an initial keypress (velocity sensitivity) or the amount of force applied after initial
impact (aftertouch) will be converted to 8-step data (3-bit resolution).
• If the Performance pad on the left deck is held pressed, the number of the lit rubber pads on the right deck will
increase/decrease in response to force applied to the Performance pad on the left.
• If the Performance pad on the right deck is held pressed, the number of the lit rubber pads on the left deck will
increase/decrease in response to force applied to the Performance pad on the right.
(With the minimum amount of force applied, one LED is lit, and with the maximum amount of force applied, all 8 LEDs are lit.)
[Display examples]
• When the amount of force applied is minimum • When the amount of force applied is maximum
(the converted value is "0"), only Performance pad LED 1 (the converted value is "7"), all Performance pad LEDs
E on the left (right) deck is lit. on the left (right) deck are lit.
26 DDJ-SR
1 2 3 4
5 6 7 8
7. DISASSEMBLY
Note: A
Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
A B C D E C C A B
A A
F F
G C
C H C
D
White White
White White
Black Black
Black Black Black
White
White Red
Black
Black Black
DDJ-SR 27
5 6 7 8
1 2 3 4
A Disassembly
18 11 3 10
2
B
17 12 4 9
16 13 5 8
1 7
15 14 6 • Bottom view
2 2
• Bottom view
MIC ground plate Phone ground plate
28 DDJ-SR
1 2 3 4
5 6 7 8
7
CN2B
CN2C CN1B
6 5 4
3 2
DDJ-SR 29
5 6 7 8
1 2 3 4
1 1
B E ring 2 E ring 2
• Bottom view
3 Wheel Assy
C
30 DDJ-SR
1 2 3 4
5 6 7 8
• Shield A
(1) Remove the FFC isolation slice by removing
the four screws.
Earth lead FFC isolation slice
(602-SL24F-099)
(2) Remove the MIC isolation slice by removing
the three screws. 1 1
(602-SL24F-099)
3 3
Screw tightening order 1 • Bottom view
3 2 D
1 CN500
1 CN500
F
PANEL-R PCB Assy PANEL-L PCB Assy
DDJ-SR 31
5 6 7 8
1 2 3 4
C Washer
Grease Grease
(GEM1096) Adhesive (GEM1096) Adhesive
Grease
(GEM1096) Wheel Assy (GYL1001) (GYL1001)
Adhesive
(GYL1001)
• Bottom view
D
Adhesive
(GYL1001) Chassis Assy
• Bottom view
Adhesive Adhesive
(GYL1001) (GYL1001)
CF fixed plate
Adhesive
(GYL1001)
F
CROSS FADER PCB Assy
32 DDJ-SR
1 2 3 4
5 6 7 8
• PCB Assy storing firmware and utility settings • Confirmation of the version of the firmware
I/O PCB Assy • Updating to the latest version of the firmware B
• Factory reset
• Be changed user setting to condition before the repair
(when be possible)
Updating Procedures
Note: Turn the power off and disconnect all the cables from the unit.
And close all applications on your computer before running this updating procedure.
1 Connect your computer to DDJ-SR via the USB cable 3 When the update file for DDJ-SR (DDJ-SR_Vxxx.jar) is
included with the product. activated, the following dialogue is displayed. Click the D
2 Turn on the power of DDJ-SX while pressing the [SHIFT] [Start] button.
button and the [SYNC] button on the LEFT deck ensure Approximately a few minutes are required for updating.
the Level meter LEDs flash before releasing your finger
from the these buttons.
E
PC
USB cable 4 When the firmware update process is complete, click the
[OK] button.
DDJ-SR 33
5 6 7 8
1 2 3 4
34 DDJ-SR
1 2 3 4
5 6 7 8
DDJ-SR 35
5 6 7 8
1 2 3 4
A
Sheet for confirmation of the user setting
Utilities mode 1
Setting of DJ software to be used Channel fader start setting Master output’ s attenuation level setting
Serato DJ Other than Serato DJ With SYNC Without SYNC disabled 0 dB -3 dB -6 dB
Utilities mode 1
Slip mode flashing setting Demo mode setting
enabled disabled enabled disabled
Utilities mode 1
B
Sampler velocity mode
Jog dial MIDI message sending interval setting
Velocity curve selection After touch setting
Curve1 Curve2 Curve3 Curve4 enabled disabled 3 ms 4 ms 5 ms 6 ms 7 ms 8 ms 9 ms 10 ms 11 ms 12 ms 13 ms
Utilities mode 2
Default value of the beat forthe hot cue roll function setting Default value of the beat forthe sampler roll function setting
1/32 1/16 1/8 1/4 1/2 1 1/32 1/16 1/8 1/4 1/2 1
Utilities mode 2
C Momentary mode setting Pad Plus mode flashing operation setting
enabled disabled enabled disabled
Utilities mode 2
Combo FX
Default value of the Combo FX level setting Default value of the Combo FX filter operation mode setting
Level 12 Level 50 Level 75 Level 100 Off Slow Quick LFO
Performance pad 1 Performance pad 1
Performance pad 2 Performance pad 2
Performance pad 3 Performance pad 3
Performance pad 5 Performance pad 5
Performance pad 6 Performance pad 6
D
Performance pad 7 Performance pad 7
36 DDJ-SR
1 2 3 4
5 6 7 8
DDJ-SR 37
5 6 7 8
1 2 3 4
- For the applying amount of lubricants or glue, follow the instructions in this manual.
or
38 DDJ-SR
1 2 3 4
5 6 7 8
3 Polyfoam 506-SR-657
4 Soft Bag 509-SR-328
5 Paster Board 507-SR-3440
6 Handle 100-SX-3017
7 Handle Base 100-SX-3018
8 Gift Box See Contrast table (2)
9 Read Before Use (Important)/ See Contrast table (2)
Quick Start Guide
B
10 Read Before Use (Important)/ See Contrast table (2)
Quick Start Guide
11 Read Before Use (Important)/ See Contrast table (2)
Quick Start Guide
12 PE Bag 505-DJM250-014
DDJ-SR 39
5 6 7 8
1 2 3 4
Wheel plate
(NSP)
Screw
(NSP)
Spring
(NSP)
Carbon pad
(NSP)
40 DDJ-SR
1 2 3 4
5 6 7 8
A
: Accessories of VR
(NSP)
E D
C
C
D
B
Bar-code
(NSP)
DDJ-SR 41
5 6 7 8
1 2 3 4
91 Screw 602-A700-494
F
92 Screw 602-PTP3012-571
93 Screw 602-ST306-728B
94 Screw 602-SW3008-737B
42 DDJ-SR
1 2 3 4
5 6 7 8
DDJ-SR 43
5 6 7 8
1 2 3 4
10/25 4.7
C900 C902 AV=20dB
220P 22/16 C903
R902
8
3 47P 5 IC900B
L C914
JK 900 4 1K 7
S 4580
3
B
MI C1 2 R900 R904 6
R 10K 47K
1 R906 -6V 10/25
G C905
4
4.7
C907 VR
1
R901 10/25 R907 20K
10K
0.1 R903 9.1K
C901 1K C904 47P
220P C908
100/16
CHASSIS AG
C C
0
CHASSIS
JK 980
3
L
2 HEADP HONES(3.5m m)
R
C980 C981 1
G
CN7 0.1
HP L 1500P 1500P CHASSIS
1 C982 JK 981
2
C W7
3
3
L
HP R 2 HEADPHONE(6.3m m)
E 4 R
1
G
C983
0.1
CHASSIS
A B
44 DDJ-SR
1 2 3 4
5 6 7 8
0dB AV=9.4dB
C914 IC900A
3
3
B
1
R908 4580
10/25 2 2
9.1K 6V
VR900 47P C910
1
20K A
R909 24K
C912 CN6
R910 0.1
2.2K C911 1
C909 MI CI N
2 C W6
47P 10/25
3
C915 4
C
0.1 C913
CHASSIS 0.1
-6V
2 D
SW950
C1
1
REVERSE AD3.3V CN701B
R950
1
C952 22K CURVE
2
REV
0.1 HP VR
3 D CN701A
4
3
C.F .CUR 5
C950 VR950 2
0.1 20K B C953 C951 E
NC
1
0.1
ADG
3
HP LEVEL
C955 VR951 2
0.1 20K B C954
1
0.1
A B
DDJ-SR 45
5 6 7 8
1 2 3 4
A
R29
R277 0
IC2A
NC 3
AV=-5.46dB
AV=0dB 1
R158 4580
2
R155 R160 100 IC1A 30K
JK 2A 3 C118 R293 NC C127 IC17
1 R167 C132 1
0 4580 C130 0.01 NC
68P 100
3
L 3 C115 2 R164 NC 2
R157 10/25 VR1A R162 A
220P 47K 2 16K 3
NC C120 GND
1 10/25
C114 R156
20K A 0.1 6V A3.3V
18 R23 C61
D
NC
14
8
2 220P C116 VR1B 5 IC2B 560
R
47K
NC 6V C236 R163 R278
47/16 5 7 L21 C58 C272
R154 R161 5 8 IC1B NC NC 6 4580 33P
C119 C133 Bead- 600
0 100 7 20K A C121 IC22 C57 D5V
AUX 4580 0.01 X1 0.1
4
6 C129 PCM1803A
R294 NC -6V R166 33P 6M C55
10/25 0.1 1 20
R159 LIN MODE1 1000P
4
3.09K
6 15 R168 22 SCK 1
52
51
50
49
48
47
46
45
44
43
42
41
40
R21
C117 C125 AGND SCK 1 D34 1000P
7 14 EDZ CT E61 6.8B C53
PDWN VDD BEAD
10/25 8 13 VUSB D35
MCLLO2
A V SS
M C L K I2
D V SS
DV DDS
PF I
X TI
MCLK I
X TO
MCLK O
SC L
C SC
SD A
BYPAS DGND C40 C42
9 12 R169 22 AUX 10/25 1 39
C 122
C 123
C 124
10/25
C 126
C 131
TEST DOUT EDZ CT E61 6.8B 0.1 PFO /CRST
0.1
0.1
0.1
22/16
10 11 R170 22 BCK 1 C45 2 38
LRCK BCK NC AVDD CDATI
D13 0.1 3 37
AD5V D36 PWMO DVDD
JK 1 1SS355 4 36
RSB6.8S D12 PLLO CDATO
R171 22 LRCK 1 1 D R20 1.5K 5 35
VB 1SS355 1 L13 DVSS CSYNC
2 4 6 34
R172 22 RST D- R19 PUR IC16 CSCLK
3 D+ 22 7 33
C136 D+ DP TUSB3200 DVSS
4 D- 2 3 R18 22 8 32
C134 DGND DM P17
5 9 31
B 0.01 0.1 CHASSIS
CHASSIS
6
D14
ACM2012 D3.3V
10
DVDD
/MRST
P16
P15
30
D 11 29
D11 1SS355 TEST P14
USB (DEVI CE) R15 C44 12 28
PL L O E N
1SS355 EXTEN P13
220 13 27
DV DD
D V SS
/X IN T
/RSTO DVDDS
D19 0.1
P11
P12
P30
P31
P33
P34
P35
P10
NC
PD SMAJ6.0A C46
0.1
14
15
16
17
18
19
20
21
22
23
24
25
26
C43 C56 C49
0.1 C48 1000P 0.1
0.1
C270 6V 41 R22
4.7K
D20 SMAJ6.0A
D R260 NC
0.1 C139 100K C137 AV=-5.46dB
W6 R279 ZD1
22/16 R175 6V C238 IC3A
NC 3
1 100 NC
8
A CN6 2
5 IC3B
47/16 R173 4580
1
/IN T
RST
7 2 ZD2
3 4580 A3.3V
6 30K NC
4
C140
C141
C142 R176 C143 42
4
R37 RST
PC O -0
PC O -1
A 0.1 -6V
C153 X2 0.1 D3.3V
1 20
C138 0.01 LIN MODE1
D 2
RI N MODE0
19
C148 IC13 ! C75
24.576M
C268
3 18
4
VREF 1 FMT1
17
0.1
45 BD12K A5F P
R44
R45
VREF 2 FMT0 D1.2V 33P 0.1 D21 SMAJ6.0A
5 16
220
C 68
C 70
VCC OSR D
COM
6 15 R177 22 SCK 1 D3.3V I O TP 7 C242 C243 C244 C245 C246 C247
C149 AGND SCK1 1000P 1000P 1000P 1000P 1000P 1000P
7 14 C64 TP 8 C263
PDWN VDD
0.1
0.1
10/25 8 13
47
47
BYPAS DGND C63 47/16 0.01
9 12 R178 22 MI C
C 144
C 145
C 146
10/25
C 150
C 151
TEST DOUT
0.1
0.1
0.1
22/16
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
C 43 R180 22 LRCK 1
IC15
D38 RSB6.8S
MOSI
R181 22 RST
PF 1/D IN 1_0
PF 0/D IN 1_1
PG 15
PG 14
NMI
X TA L
C L K IN
SC L
V DDEX T
V D D IN T
RE SE T
E X T _W A K E
PG
SD A
E X T C L K /SC L K
PPI_C L K
C65 0.1
C152
0.01 44 C147
0.1
BCK 1 R38
LRCK 1 R39
47
47
1
2
RBCK 1 PG13/SS1
48
47
47
47
R48
R256
SS
HREQ
RL RCK 1 PG12
D 3 46 0.1
VDDEXT VDDEXT C72
HP R40 47 4 45
PF4/DO1_1 PG11 MAS R182
BOT R41 47 5 44 47 R49 MI SO
PF5/DO1_0 PG10/MI SO1 BCK 2 R183
BCK 2 R42 47 6 43 47 R50 MOSI
PF6/TBCK 1 PG9/MOSI 1 LRCK 2 R184
LRCK 2 R43 47 7 42 47 R51 SCL K
PF7/TL RCK 1 PG8/SCK 1 SCK2 R185
-6V 8 41 0.1 C74
VDDI NT 6.2 * 6.2 m
m GND VDDI NT
5V C66 0.1 9 40
VDDI NT VDDI NT
10 39 47 R52 LRCK 2 C
PF8 PG7/TL RCK 0
R150 11 38 47 R53 BCK 2
D24 TP 1 PF9 PG6/TBCK 0
470K D31 A5V 12 37 47 R54 PCI -0
SM5819A TP 2 PF10 PG5/DO0_0
13 ADSP -BF 592 36 47 R55 MAS
MUTE
Q21 SM5819A
C67
TP 3
0.1 14
15
PF11
VDDEXT
PG4/DO0_1
VDDEXT
35
34 47 R56 LRCK 1
25
PG 0/D IN 0_1
PG 1/D IN 0_0
PF12 RL RCK 0
A124TK A R153 R151 16 33 47 R57 BCK 1
BMODE2
BMODE1
BMODE0
TP 4 PF13 RBCK 0
V DDEX T
V D D IN T
1K 82K 0.1 C73
G PA D
T RST
PF 14
PF 15
EMU
TMS
GND
TDO
TCK
TDI
R152
65
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
10K
D23 Q22
5V
MUTE- M CN5
1SS355 C112 C113
22
22
22
22
22
22
47
47
68u/25 D33
C 69
C 71
330/10 TDO D1.2V
2SC2712GR 14 13
HOL E1 HOL E2 HOL E3 HOL E4 HOL E5 HOL E6 TDI TP 5
A 12 11
TRST
0.1
0.1
5V 10 9 TP 6
TCK EDZ CT E61 6.8B
1 1 1 1 1 1 8 7
TMS
R58
R59
R60
R61
R62
R63
A U X R46
M IC R47
C 223 Short
IC14 6 5
D C248 C249 C250 C251
C224 C225 1 5 4 3
A A A NC VCC EMU
D CHASSI S CHASSI S CHASSI S CHASSI S 0.1 CHASSI S CHASSI S 0.1 2 2 1 1000P 1000P 1000P 1000P
T RST
EMU
SUB
TMS
TDO
TCK
TDI
3 4
GND VO DSP JTAG
D D D BD4745G
1 1 1 1 1
C 226 Short
BOT R214
C259 C260 C261 C262 BCK2 R215
CHASSI S 0.1 CHASSI S CHASSI S NC CHASSI S 0.1 CHASSI S 0.1 IC12 LRCK2 R216
NC SCK2 R217
D D D D D L17
I O C
NC
G
Bead C4 C13
18K R297
22K
8
7
SS
FREQ
COMP
FB
1
2
51K /1%
IC11
BA05F P
! 8 BEAD
L8 DA3.3V
0.47(MEF ) 6 3
100/10 IN EN A5V L7 AD5V
R6
10K
Q4 LED- G
0.1
Q39
5
SW GND
4
R10 I O 4
C11 C3 Com ment: TPS61085 8.2K BEAD
5
G
C35 C15
E 2SC2712GR NC 100/16(L )
R296
2SC2712GR
C14
IC9
C26
! R12 C34 C10
47/16
C235 0.1
C24 C28 C32 C16
C264 6.8K 1u 13K /1% 47/16 NC 1000P C17
1200P NC 0.1
R8 pattern connect 3.3/50 10/10 0.1 0.1
C9 4.7K C23 C30
L3 C20
2.2/50 10/10 NC 0.47(MEF )
NC
C230 3.3V L1 D3.3V PD A
L19 C25 C31 C19
L10 NC 0.47(MEF ) D3.3V 6V -6V AD5V
22uH/1.11A BEAD
! 0.1uF D32 C233 C234 22uH/1.11A C33
L18
1
IC27 TP S54232
BOOT PH
8
SM5819A 10/10 NC
C6 C2 1 C21
10/10
C12
0.1 1
!
IC10 TP S54232
0.1uF
8
D6
SM5819A R13
30K
C22 C29
NC
47/16 C280
0.1
C279
0.1
C278
0.1
C277
0.1
0.1 47/16 10/10
2 7 L2 BOOT PH HP R234
D5V
Bead
R299
3
4
VI N
EN
SS
GND
COMP
VSNS
6
5 R288
D
Bead
2
3
4
VI N
EN
GND
COMP
7
6
5 R3
6 D
BCK2
LRCK2
R235
R236
15K 18K /1% SS VSNS D5V AD5V DA3.3V SCK2 R237
1.8K
C231
C27
1000P
270P C283 C282 C281
0.1 0.1 0.1
C228 C5 R289 R290 C265
R298 C285 C229 R9 R14 A
5.6K /1% 30K C232 10/25 C37
10K 1u
10/10 0.1 0.015uF 47P
0.027uF
4.7K 47K C38
12P L9 39
TPS54232 Layout Rule , Please consult the attachment (TPS54232-Layout.pdf)
TPS54232 Layout Rule , Please consult the attachment (TPS54232-Layout.pdf) Bead
-6V
C
46 DDJ-SR
1 2 3 4
5 6 7 8
R292
C I/O PCB ASSY (704-SR-A596) A
0
S13
S12
S14
S11
S15
S10
SD A 1
M O SI
A D 7b
A D 6b
SC L K
M ISO
SC L 1
SS
S2
S5
S3
C50 D3.3V
S6
S1
S4
A D 15
A D 14
A D 13
A D 11
A D3
A D2
A D1
D3.3V
NC
C240
IC17
100
100
100
100
NC
2K
1K
2K
2K
2K
2K
2K
2K
2K
2K
2K
1K
22
22
220
220
1 5
NC NC VCC
2
A
220
220
220
220
220
220
220
3 4 D C254 C255 C256
GND Y
R111
R112
R113
R114
R115
R116
R117
R118
R119
R120
R121
R122
R101
R102
R103
R104
1000P 1000P 1000P
18
R69
R70
R98
R99
R23 C61 NC R269 NC
D R123
560 0.01 C87
R82
R83
R84
R85
R86
R87
R88
R27 R28 D15 D17
C58 C272 0.01 C88 4.7K
33P NC NC R270
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
NC IC20 C80 TP 9
D5V ADG 0.1 560P C103
1 0.1 4.7K 4.7K
M C98 SW2
C55
PT D 7
PT D 6/A D 7b
PT D 5/A D 6b/T PM 0_C H 5
PT D 4/T PM 0_C H 4
PT D 3/T PM 0_C H 3
PT D 2/PT M 0_C H 2
PT D 1/A D 5bT PM 0_C H 1
PT D 0/T PM 0_C H 0
PT C 17
PT C 16
PT C 13
PT C 12
PT C 9
PT C 8
PT C 4/PC S
560P C90
PT C 6/M O SI
PT C 10/I2C 1_SC L
PT C 7/M ISO
PT C 11/I2C 1_SD A
PT C 5/SC K
1000P 100/10 BOOTH/MASTER
SCL S7 2K R105 1 60 560P C102
C47 PTE0 VDD D3.3V R259 D3.3V
SDA S8 2K R106 2 59
0.1 PTE1 VSS 22K 0.01 C89
D3.3V S9 2K R107 3 58
1
C1
2
D16 D18 PTE2 PTC3/L U_P 7
NC NC MUTE- M 4.7K R108 4 57 560P C91
PTE3 PTC2/AD11
22K K EY1 220 R64 5 56
51
50
49
48
47
46
45
44
43
42
41
40
D V SS
DV DDS
PF I
X TI
MCLK I
SC L
C SC
X TO
MCLK O
SD A
R262
R263
R264
R24 C77 VDD PTB19
39 100 PCI -0 8 53 220 R75 DATA7 NC R265
/CRST R25 VSS PTB18
38 100 PCO- 1 9 52 220 R76 DATA6 220K R266
D CDATI PTE16/AD1 PTB17
37 R128 K EY3 220 R66 10 MK L15Z128VL K 4 51 220 R77 DATA5 NC R267
MO DVDD 22K PTE17/AD5a PTB16
36 R26 100 PCO- 0 11 50 220 R78 DATA4 NC R268
220K
220K
220K
O CDATO PTE18/AD2 PTB11
35 R129 K EY4 220 R67 12 49 220 R79 DATA3
S CSYNC 22K PTE19/AD6a PTB10
34 13 48 220 R80 DATA2
CSCLK PTE20/AD0 PTB9 ADG
150
150
TUSB3200 32 22K 15 46
P17 C241 PTE22/AD3 PTB3/AD13
PT E 25/I2C 0_SD A
D5V
PT E 24/I2C 0_SC L
PT A 0/SW D _C L K
PT A 3/SW D _D IO
31 1000P HREQ 100 R257 16 45
D P16 C52 PTE23/AD7a PTB2/AD12
B
R29
R30
R31
30 IC18 17 44
PT E 29/A D 4b
PT E 30/A D 23
ST P15 VDDA PTB1/AD9 C81 C99
1
20
29 D 0.1 74HC4050 Bead- 120 18 43
T P14 AD3.3V VREH PTB0/AD8
19 100/10 IC21
EX TA LO
28 L15 19 42
V CC
22 R100 RSTB
PL L O E N
PT A 12
PT A 13
PT A 14
PT A 15
PT A 16
PT A 17
+V
PT E 31
27 3 2 R16 220 SCK 1 C93 20 41 D5V
PT A 1
PT A 2
PT A 4
PT A 5
DV DD
D V SS
/X IN T
V DD
TO DVDDS 1A 1Y VSSA XTAL O C100
V SS
5 4 R17 0.1 2 18 LED1
220 SCK 2 0 R124 22P 1A1 1Y1
P11
P12
D22
P30
P31
P33
P34
P35
P10
NC
2A 2Y R132 4 16 LED2
7 6 R33 47 LRCK 1 560P C105 C96 X3 SMAJ6.0A 1A2 1Y2
C51 3A 3Y 1M L16 6 14 LED3
9 10R34 47 LRCK 2 47/16 8M 1A3 1Y3
0.1 4A 4Y 560P C104 8 12 LED4
15
16
17
18
19
20
21
22
23
24
25
26
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
C56 C49 11 12R35 47 BCK 1 C101 NC 1A4 1Y4
5A 5Y R109 R110 22P 1
C48 1000P 0.1 14 15R36 47 BCK 2 560P C85 C227 C266 /1G
6A 6Y 74HCT244
GND
22
22
22
22
560P C86 11 9 LED5
220
220
220
220
R22 R131 CN4 R133
47
4.7K IC19 2A1 2Y1
C62 10K 0.1 NC 13 7 LED6
2A2 2Y2
220K
220K
220K
220K
R32 1 8 1 D3.3V 15 5 LED7
220
220
220
220
8
D20 SMAJ6.0A NC
4.7K
ADG A0 VCC C78 VDET
4.7K
2 7 C97 2 SWD_DI O 2A3 2Y3
0.1 17 3 LED8
R71
R94
R95
R96
R97
R72
R73
A1 WP
R258
R125
0 2A4 2Y4
GND
3 6 3 GND 19
A2 SCL R134 /2G
4 5 0.01 4 SWD_CL K
A D 8 R89
A D 9 R90
A D 12 R91
A D 0 R92
GND SDA NC
R271
R272
R273
R274
11 19
DA TA 1
DA TA 2
DA TA 3
DA TA 4
DA TA 5
DA TA 6
DA TA 7
DA TA 8
D 5 /RST
NC
10
24L C02BT
V DET
ENCA
ENCB
SD A 1
W R-A
W R-B
W L -A
W L -B
RST B
SC L 1
SD IO
SD IO
CON5 C95 D
/IN T
SD A
CLK
CLK
SC L
RST
LED- G
A
B
C
AD3.3V
R93 BOOTH
MAS R275 220 CN1A
3
220
R276 2 VR2 C82 D3.3V
C92 1
22K R261 20K B 0.1 D5V
0.01 2
220K AD3.3V
3
1
C269 ADG AD0
4
D3.3V AD1
243 C244 C245 C246 C247 D25 R188 5
D A AD2
000P 1000P 1000P 1000P 1000P MUTE 6
1SS355 150K 0.1 AD3
Q24 7
AD11
2SD2704K 8
ADGND
9
D37 RSB6.8S AV=9.63dB K EY1
10
MI SO 100/16(L ) C166 11
K EY2
K EY3
D38 RSB6.8S C170
12
LED1 C
MOSI DA3.3V
6V 20 26 13
14
LED2
C274
C167
D CN1B 15
LED3
8
C172 NC
5 IC4B 47/16 C179 LED4
47
47
R48
R256
SS
HREQ
23 22 21 0.1
D C159 R186
470P
R190 6
4580
7 100/10
R203 470 R210 30
16
17
LED5
LED6
C156 C273 18
0.1 0.1 1K C163 NC LED7
C72 IC24 CS4344 3.3K C169 6V R206 19
4
3.3K
R191
1K
2 4580 470P
C178 100P
100/10 R205 470 R212 30 CHASSI S
29
30
DGND
C201 NC
5 IC6B 16
30 29 28 0.1
C189 C275
D C192 R218
470P
R222 6
4580
7 33 17
18
LED4
LED5
LED6
0.1 1K 19
IC25 CS4344 3.3K C197 LED7
4
100/10 NC Q31 20
BOT R214 22 1 10 100/16(L ) -6V C206 R228 820 LED8
SDI N OUTR R284 2SD2704K R232 180 JK 5A 21
BCK2 R215 22 2 9 10K 100/16(L ) S1
SCL K VA 22
LRCK2 R216 22 3 8 100/10 S2
LRCK GND R226 C204 3 L 23
SCK2 R217 22 4 7 C194 C195 C203 100K S3
MCL K OUTL 220P R230 2.7K 220P 24
L17 5 6 1800P R225 S4
VQ FILT 1 25
S5
C187 C202 R285 10K 26
C190 C191 C200 R231 2.7K C205 S6
NC 0.1 10/25 10/25 28 1800P
470P 3
10K
IC6A
27 C207
R227
100K
220P 2
R
27
28
A
B
C193 1 29
V L20 A3.3V
32 31 D
C188
0.1
R219
3.3K
R223
1K
2 4580
100/10 R229 820 Q32
2SD2704K
R233 180 BOOTH/MASTER2 30
31
C
WL -A
WL -B
100/10 C199 32
100uH LED- G
C8
0.1
C36
22/16
9 R224
10K
220P
33 CHASSI S
33
34
DGND
37 36 35 DA3.3V
R286
NC
3 IC7A C252
R252 22,1/4W R254 10,1/4W
10
11
K EY3
K EY4
C213 1 12
C210 R238 R242 4556 K EY5
2 13
470/10 LED1
HP R234 22 1
IC26 CS4344
10 47/16 47/16 6.8K C217
3.3K
C221 40 40 14
15
LED2
G
SDI N OUTR LED3
BCK2
LRCK2
SCK2
R235
R236
R237
22
22
22
2
3
4
SCL K
LRCK
MCLK
VA
GND
OUTL
9
8
7
C219
470P R244
24K
180P
R248
2.7K
Q35
2SD2704K
R249
2.7K
Q36
2SD2704K
W7 CN2C 16
17
18
LED4
LED5
LED6
5 6 AV=10.95dB 1 19
C208
0.1
VQ
C211
10/25
FILT
C212
10/25
35
1500P
C220
1500P C216
R246 ! 40 40
2
3
4
B CN7 20
21
22
23
LED7
LED8
S10
S11
10/25 R250 R251 S12
3.3,F RN 1/4W
39 38 C209
0.1
6V
34 2.7K
Q37
2SD2704K
2.7K
Q38
2SD2704K
24
25
S13
S14
8
D C218 5 IC7B A 26
470P S15
C214 7 27
R239 R243 4556 C253 A
6 R253 R255 28
B
6.8K 3.3K R247 ! 29
C
4
D30 R241
Q34
2SD2704K C108 C109
F
MUTE NC NC
1SS355 150K
D ADG
C
DDJ-SR 47
5 6 7 8
F
E
B
A
D
C
48
D
1
1
3
3
MASTER C716 LOW- R R710 R711 R721 R725
VR700 2 2 VR704 D701 D711 D715
C700 C708 100 D700 100 47 100
20K B 20K B
0.1 C704 0.1 C712 0.1
IC700 0.01 RED RED AMBER GREEN
3 1
3 1
0.01 1 16
4 VDD MI D- R LED2
VR701 2 MI D- L 2 15 2 VR705
C701 6 2 C709
20K B 3 14 20K B
0.1 C705 COM 1 0.1 R712 R713 R722 R726
4 13 C713 D703 D712 D716
7 0 100 D702 100 47 100
0.01 5 12 0.01
3 1
3 1
5 3
6 11
2
2
3 1
3 1
R737 R714 R715 R727
R700
R701
R702
HI -R NC D731 100 D704 100 D705 100 D717
VR703 2TRI M- L 2 VR707
C703 20K B 20K B C711
0.1 C707 C715 0.1 NC RED RED GREEN
100
100
100
1
1
0.01 0.01
LED4
DDJ-SR
ADG C
B R738 R716 R717 R728
A NC D732 100 D706 100 D707 100 D718
AD3
AD0
10.3 MIXER and CROSS FADER PCB ASSYS
3
3
AD3.3V
R718 R729
D708 D719
3
200 100
HP -CUE.MAS C717
VR708 2
R703
R704
R705
C718 20K B RED GREEN
0.1 C722 0.1 LED6
0.01 IC701
3 1
1 16
100
100
100
4 VDD CN701A R730
VR709 2 FIL-R 2 15 D720
C719 6 2 100
20K B 3 14
B
3 1
5 3 3
6 11 HP VR
VR710 SAMP LER INH A 4 LED7
2 7 10
C720 VEE B C728 5
20K B 8 9
VSS C R719 R724 R731
CN701B
4
4
3 1
3
C726
VR711 2 LOW- L 2 VR712 TO FRONT CN701B RED AMBER GREEN
C721 20K B 20K B FIL-L
C725 C727 LED8
0.1
1
1
0.01 0.01
R720 R723 R732
ADG 200 D710 200 D713 100 D722
E
CN700 W700 AD3.3V
3
C732
(
1 1 10 /10 K EY1
C
C721 20K B 20K B FIL-L
C725 C727 LED8
0.1
1
1
0.01 0.01
R720 R723 R732
ADG 200 D710 200 D713 100 D722
E
CN700 W700 AD3.3V
3
C732
1 1 10u/10 K EY1
VR715
2 AD2 SW705
2 2
20K B LEVEL
3 3 C731 SW701 SW703
1
5
5
3P 3P 0.01 TACT TACT
1
2
VR713 D728
1SS355 1SS355
20K B CH1- FA CUE- L CUE- R 1SS355
C729 AD1
K EY2
0.1
0.01 C733 SW702 SW704 SW707
VR714 TACT TACT TACT
D724 D727 D730
(704-DJM250-A032)
20K B CH2- FA
C730 AD11 1SS355 1SS355 1SS355
0.1 BACK LOAD- R LOAD- L
6
C737
47u/16 K EY3
CN1B
D3.3V SW706
1 D3.3V TACT
D5V
2
AD3.3V D729
3
AD0 0.01
4 C739 22K R706 1SS355
AD1 SW700
5
AD2 ENCB 10K 1 5 LOAD P REP ARE
6
AD3 R7082
DDJ-SR
7
AD11 ENCA 10K R7093 4 D725
8
ADGND 1SS355
9 22K
K EY1 C740 BROWSE
10 0.01 R707
K EY2
11
K EY3
12
LED1
13
7
7
LED2
14
LED3
C
15
LED4 D
16
LED5
17 D5V
LED6
18
LED7
CN1A
19
LED8 R734 R735 R736
20
S7
21 33K 33K 33K
S8
22
S9 Q700 Q701 Q702
23
A 2SD1757 2SD1757 2SD1757
24
B
25
C
(704-SR-A597)
26
ENCA
27
ENCB
8
30
S7
S8
S9
C741
C738
10/25
10u/25
LED- G ADG
D E
49
F
E
B
A
D
C
F
E
B
A
D
C
50
F G
R595
1
1
22K
R508
WL -A 22K
A
B
C
Q506 D502 R510
A D 12
2SC2712GR
470
R500
R501
R502
LTH- 301-07 C519
D3.3V
AD3.3V D
100
100
100
D503 10/10
3
FX1- 1
P500 C503 2 VR500 Q507
C504 R511
20K BX2 20K B 2SC2712GR
TEMP O- L C510
0.1 0.1 LTH- 301-07 470
B1
A1
WL -B
IC500 0.01 R509
3 1
B4 B2 A4 A2 1 16 FX1- 2
4 VDD 22K
C509 2 15 2 VR501 C505
6 2
C502 3 14 C511 20K B R596
COM 1
B3
0.1
A3
C500 C501 0.1 0.01 4 13
7 0 22K
47u/16 0.1 5 12 0.01
3 1
5 3
C508 0.01 6 11 FX1- 3
INH A
7 10 2 VR502 C506 3mm HYPER LED 50 PCS
VEE B
8 9 C512 20K B
VSS C
2
0.1
2
3 1
BEATS- L
2 VR503 C507 RUBBER P AD L ED(421)
C513 20K B
0.1 LED1
1
R584 R588
0.01 NC NC
ADG R530 R531 R546 R554 R562 R571 R578 R579
C516 AD3.3V D505 D584 D520 D528 D536 D544 D552 D588
100 100 47 200 200 200 100 100
10.4 PANEL-L and R PCB ASSYS
1/16
IC501 D504 D553
HOL E500 HOL E501 PIC16F 616 C515 FX- 1 FX- 1 BL UE SYNC RED ASSI GN 2 AUTO L OOP
1 14 0.1 AUTO L OOP
C529 C530 VCC GND LED2 FX- 1 AUTO L OOP
1 1 2 13
RA5 RA0 R505 R585
3 12 1K C518 NC
0.1 0.1 RA4 RA1 R532 R533 R547 R555 R563 R572
4 11 R507 1000P D507 D585 D521 D529 D537 D545
RA3 RA2 2.4K 100 100 47 200 200 200
CHASSI S D CHASSI S D 5 10
RC5 RC0
DDJ-SR
R503 6 9 D506
RC4 RC1 WHEEL -L
51K 7 8 FX- 2 FX- 2 BL UE SL IP RED ASSI GN 1
RC3 RC2 EDZ CT E61 6.8B
IN
D501 LED3 FX- 2
R504 R586
20K R506 R534 R535 NC R548 R556 R564 R573
C517 1K 100 100 D509 D586 47 D522 150 D530 200 D538 200 D546
L500
1/16
D508
C535 0.1 C536 0.1
CHASSI S 100uH D500 FX- 3 FX- 3 BL UE PAD RED VI NYL
CHASSI S D D
3
3
17
AD3.3V R514 D517 D526 D534 D542 D550 D582
FSR1 1 16 75 75 47 200 200 56 82
0Y VCC
3.3K FSR3 2 15 D516
4
CN500 2Y 2X
4
R515 3 14
R522 C525 YCOM 1X SL ICER BL UE PARAMETER1 RED PLAY/P AUSE SL ICER
1 3.3K FSR4 4 13 AD8
TP 1 3Y XCOM
2 C521 100 FSR2 5 12 LED8 SL ICER
TP 2 R523 0.01 1Y 0X
3 6 11
TP 3 INH 3X
4 100 7 10 R528 100 A R544 R545 R553 R561 R569 R577 R583
TP 4 VEE A D519 D527 D535 D543 D551 D583
5 8 9 R529 100 B 75 75 47 200 200 200 82
TP 5 0.01 GND B
6 D518
TP 6
PAD
7 ADG 74HC4052
TP 7 R516 SAMP LER BL UE PARAMETER1 RED JOG SAMP LER
8
TP 8
9 3.3K AD9 SAMP LER
10 R517
R524 C526
3.3K K EY1
Molex FFC10P
R525 C522 100 0.01
C514 C528 FSR5
FSR6 SW500 SW505 SW510 SW514 SW518 SW522
0.1 100 K EY L OOK JOG PAD AUTO L OOP 2X PARAMETER1
10/10
ADG 0.01 D554 D559 D564 D568 D572 D576
AD
7 ADG 74HC4052
TP 7 R516 SAMP LER BL UE PARAMETER1 RED JOG SAMP LER
8
TP 8
9 3.3K AD9 SAMP LER
10 R517
R524 C526
3.3K K EY1
Molex FFC10P
R525 C522 100 0.01
C514 C528 FSR5
FSR6 SW500 SW505 SW510 SW514 SW518 SW522
0.1 100 K EY L OOK JOG PAD AUTO L OOP 2X PARAMETER1
10/10
ADG 0.01 D554 D559 D564 D568 D572 D576
5
100 FSR8
0.01 1SS355 1SS355 1SS355 1SS355 1SS355 1SS355
16
47/16 CN2B SYNC SHI FT ASSI GN 2 DECK 3/4 VI NYL ASSI GN 1
CN2C D3.3V D556 D561 D566 D570 D574 D578
1
D3.3V D5V
1 2 1SS355 1SS355 1SS355 1SS355 1SS355 1SS355
D5V AD3.3V
2 3
AD3.3V (AD7b) AD6b
3 4 K EY4
(AD7b) AD6b (AD13) AD8
4 5
(AD13) AD8 (AD14) AD9
5 6
(AD14) AD9 (AD15) AD12 SW503 SW508 SW513 SW517 SW521 SW525
6 7 FX- 1 FX- 2 FX- 3 TAP SL IP DECK 1/2
(AD15) AD12 ADGND
7 8
ADGND K EY1 D557 D562 D567 D571 D575 D579
8 9
K EY1 K EY2
9 10 1SS355 1SS355 1SS355 1SS355 1SS355 1SS355
K EY2 K EY3
10 11
K EY3 K EY4
11 12 K EY5
K EY4 K EY5
12 13
K EY5 LED1
13 14
LED1 LED2 SW504 SW509
14 15
C
C
LED2 LED3 CUE PLAY/P AUSE
15 16
LED3 LED4 D558 D563
16 17
LED4 LED5
17 18 1SS355 1SS355
6
LED5 LED6
6
18 19
LED6 LED7
19 20
LED7 LED8
20 21
LED8 S1
21 22
S1 S2
22 23
S2 S3
23 24
S3 S4
CN3A (G)
CN2A (F)
24 25
S4 S5
25 26
S5 S6
26 27
S6 A
27 28
A B
28 29
B C
29 30
C (WR- A) WL -A
30 31 Q500 Q501 Q502 Q503 Q504 Q505
(WR- A) WL -A (WR- B) WL -B
31 32 LED- G 2SD1757 2SD1757 2SD1757 2SD1757 2SD1757 2SD1757
(WR- B) WL -B LED- G
32 33
LED- G DGND
33 34
DDJ-SR
DGND R589 R590 R591 R592 R593 R594
34
3.3K 3.3K 3.3K 3.3K 3.3K 3.3K
15
C532 D5V
C532C C534
C534C
10/10 10u/25
S1
S2
S3
S4
S5
S6
7
*PN Request. Please Refer "DDJ-SR QA_Request list (ele)-0329_3.xlsx" .
F
(704-SR-A598)
(704-SR-A599)
8
8
PANEL-L PCB ASSY
F G
51
F
E
B
A
D
C
1 2 3 4
10.5 WAVEFORMS
1 C2 + side (D3.3V) 6 C33 - side (-6V) 11 IC20 pins 27, 28 16 CN2B pin 4
2 C3 + side (+5V) 7 C34 + side (+6V) 12 SLIDER VR pin (AD) 17 CN500 pins 2 to 9
4 C16 (DA3.3V) 9 C36 + side (A3.3V) 14 SELECT SW pin (AD) 19 IC21 pins 7, 8
5 C17 (AD5V) 10 TACT SW pin 15 CN2B pins 31, 32 20 IC5 pins 1, 7 (1 kHz IN)
52 DDJ-SR
1 2 3 4
5 6 7 8
21 IC24 pins 7, 10 (1 kHz IN) 26 Q25 to Q28 base (-6V) 31 IC25 pin 3 (LRCK) 36 IC26 pin 1 (HP)
22 IC24 pin 1 (MAS) 27 IC6 pins 1, 7 (1 kHz IN) 32 IC25 pin 4 (SCK) 37 IC26 pin 2 (BCK)
23 IC24 pin 2 (BCK) 28 IC25 pins 7, 10 (1 kHz IN) 33 Q31, Q32 base (-6V) 38 IC26 pin 3 (LRCK)
24 IC24 pin 3 (LRCK) 29 IC25 pin 1 (BOT) 34 IC7 pins 1, 7 (1 kHz IN) 39 IC26 pin 4 (SCK)
25 IC24 pin 4 (SCK) 30 IC25 pin 2 (BCK) 35 IC26 pins 7, 10 (1 kHz IN) 40 Q35 to Q38 base (-6V)
DDJ-SR 53
5 6 7 8
1 2 3 4
54 DDJ-SR
1 2 3 4
5 6 7 8
DDJ-SR 55
5 6 7 8
1 2 3 4
SIDE B
D
A MIC PCB ASSY
CN6 CN7
F
IC900
C W7
A B
56 DDJ-SR
1 2 3 4
5 6 7 8
A
SIDE A
CN701B
B
E
CN701B
D
CN701A
B
DDJ-SR 57
5 6 7 8
1 2 3 4
1
B
3
6
8
9
7
4 5 40
W7 B CN7 34 35 1 2 3
36 37 38 39
4 CN2A F CN2B 11 CN1A D C
SIDE B
W7 CN2A CN1A
C 33 33
58 DDJ-SR
1 2 3 4
5 6 7 8
9 30 31 32 SIDE A
2 3 4 C I/O PCB ASSY A
Q29
IC16
Q25-Q28 Q30
IC27
IC2
IC16 IC6 IC15
IC25
IC22
IC5
IC4
43 Q39 Q23 B
Q40
46 IC18
IC24
42
IC19
IC10
A
W6
CN6
IC3
IC23
41 IC20
IC21
45
44
Q35-Q38 IC7
Q21
C
IC26
Q22
IC14
Q33
Q43
IC12
IC11
W6
IC9
Q24
Q31 IC1
Q32
Q4 IC13
Q5 F
C
DDJ-SR 59
5 6 7 8
1 2 3 4
C
CN1B
E
CN701A
E CROSS FADER
D E PCB ASSY
60 DDJ-SR
1 2 3 4
5 6 7 8
SIDE B SIDE B
D MIXER PCB ASSY A
IC700
IC701
CN1B
Q700-Q702 C CN1A D
E
CN701A
B CN701B
W700 (SIDE A)
CN01
F
E CROSS FADER
PCB ASSY D E
DDJ-SR 61
5 6 7 8
1 2 3 4
CN2B
CN2C
CN500
F G
62 DDJ-SR
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
F PANEL-L PCB ASSY
G PANEL-R PCB ASSY
IC500
Q506
Q507
C
CN2A (F)
IC501
CN3A (G)
C
CN2B
C
16
CN2C
15 D
Q500-Q505
IC502
F
17
CN500
To
CARBON PAD
F G
DDJ-SR 63
5 6 7 8
1 2 3 4
- Although the cables that are directly mounted on each PCB Assy are listed individually as electrical parts of the
corresponding PCB Assy in the parts list, those cables are included with each PCB Assy for service when it is supplied.
Mark No. Description Part No. Mark No. Description Part No.
Q 5,40 416-UDJ200-347
LIST OF ASSEMBLIES D 6,7,24,31,32 414-007USB-148
MIC PCB ASSY 704-SR-A601
HEADPHONE PCB ASSY 704-SR-A600 D 11-14,23,25,26,29,30 414-CD1000-075A
I/O PCB ASSY 704-SR-A596
D 10 414-DDJLE-348
MIXER PCB ASSY 704-SR-A597
B D 36-38 414-DJ1100G-207
CROSS FADER PCB ASSY 704-DJM250-A032
D 33-35 414-RMP3-285
D 19-22 414-UDJ200-284
PANEL-L PCB ASSY 704-SR-A599
PANEL-R PCB ASSY 704-SR-A598
MISCELLANEOUS
VR 1,2 VR FIXED PLATE 300-6000-1874
PH FIXED PLATE 300-S1-2061
GROUND PLATE 300-S1-2069
SW1,2 SLIDE SW 403-COMBO-427
W 7 4P CONNECTOR WIRE 404-SR-3797
Mark No. Description Part No.
C
A MIC PCB ASSY
MISCELLANEOUS
W 6
L 20
JK 1
4P CONNECTOR WIRE
INDUCTANCE
USB JACK (USB-B (F))
404-SR-3799
415-USOLOPA-342
420-007USB-150
FIXED PLATE 300-4500-2010A JK 2,5 2P RCA JACK 420-HDJ7000-045
VR FIXED PLATE 300-6000-1874 JK 3,4 3P PHONE JACK 420-HMJ1001-5034
PH FIXED PLATE 300-S1-2061
CN 6 4P SOCKET 404-DCM270E3-878A X 1 CRYSTAL (6 MHz) 427-S1-143
JK 900 MIC JACK 420-SMX211-137 X 2 CRYSTAL (24.576 MHz) 427-S1-145
X 3 CRYSTAL (8 MHz) 427-SUB-149
RESISTORS SPONGE 612-4MIX-416
VR 900 418-SR-712 L 21,22 CHIP BEAD 415-1300-240A
RESISTORS
C 225,230,259,261,262,266-283 413-DCM280-773
64 DDJ-SR
1 2 3 4
5 6 7 8
Mark No. Description Part No. Mark No. Description Part No.
C 4,98,99,159,160,192,193 413-HMA2200-5017 D 504-511,528,529,531-547,551-553,580-583 410-DJ5000-253T
C 179-182,206,207 413-HMA2200-5017
C 264 413-HPR1-821 MISCELLANEOUS
C 252,253 413-HT8015-169 A
CN 500 10P FFC CONNECTOR 404-CDMIX2-1142
CN 2B 34P 1.0 FFC SOCKET 404-SR-3805
C 18-20,284 413-QSPAND-632 1P GROUND WIRE 406-SR-1266
C 1,118,119,125,126,129,130 413-SPPW3-235 L 500 INDUCTANCE 415-USOLOPA-342
C 142,149,150,157,158,190 413-SPPW3-235 D 528,548-550 LED HOLDER 504-RMX30-158
C 191,211,212,215,216 413-SPPW3-235
C 36,131,139,140,151 413-SPPW3-236 SW504,509 TACT SW 403-DDJLE-416
SW500-503,505-508,510-525 TACT SW 403-DDJLE-419
SW504,509 TACT SW
504-RMX30-158
403-DDJLE-416
CN C01 3P SOCKET 404-KMD3500-609A SW500-503,505-508,510-525 TACT SW 403-DDJLE-419
PC SHEET (PC 1.5T) 501-EN2000-2469
RESISTORS
RESISTORS R 506 412-3113-078
VR 715 418-DJM250-674 VR 500-503 418-SR-706
P 500 SLIDE VR (20KB*2) 418-SR-705
E
D 548,549 410-HDJ2000-162T
D 502,503 417-HDJ2000-411
D 554-579 414-CD1000-075A F
D 500,501 414-RMP3-285
D 512-519 410-CDI600-357T
DDJ-SR 65
5 6 7 8