Professional Documents
Culture Documents
Interconnect Link Installation II-102651-EN - LR
Interconnect Link Installation II-102651-EN - LR
Installation Instructions
Revision 00 (06/08)
TIL-US1-HL
IONTM-B Series 2-fiber Interconnect Link for LMR700, LMR800, Cell850, LMR900, AWS, and
PCS1900 Extended
1 Master cable kit (C) including: 1 Slave cable kit (F) including:
1 RF jumpers SMA-m 17 RF jumpers SMA-m
1 RF jumper SMB-f 1 RF jumper SMB-f
C
F
A B D E
NOTE Before inserting the boards into the TPRNx4 subrack, make sure to set the RS485
address. It must be different for Master and Slave subracks. Refer to TPRNx4
Installation Instruction for more information on address setting.
RF IN
DL RF IN DL RF IN DL
1
PWR HDD
UL DL
RX
UL DL RST
C RST
C
DL DL DL
HIGH BAND
1
ALARM
RF IN
UL RF IN UL RF IN UL
UL UL UL
Master Side
COM 1
Carefully insert the TMRX-200 and the TDTX-300 boards into 2 adjacent slots of the Master subrack, and lock
the screws on the 4 corners of each board.
WARNING!
Only active TPRNx4 sub-rack can be used to house the Interconnect Link.
2
RF IN
DL RF IN DL RF IN DL
PWR HDD
UL DL
RX
UL DL RST
C RST
C
DL DL DL
HIGH BAND
1 ALARM
RF IN
UL RF IN UL RF IN UL
Master Side
UL UL UL
COM 1
Use the SMA-m jumper to connect the RF Out Port of the TMRX-200 board with the RF In Port of
the TDTX-300 board; use the SMB-f jumper to connect the 10.7MHz ports of the two boards
each other.
RF IN
DL RF IN DL RF IN DL
PWR HDD
UL DL
RX
UL DL RST
C RST
C
DL DL DL
3
HIGH BAND
1 ALARM
RF IN
UL RF IN UL RF IN UL
UL UL UL
COM 1
WARNING!
Make sure to connect:
- the DL optical jumper to the optical port of the TDTX-300 board;
- the UL optical jumper to the optical port of the TMRX-200 board.
NOTE Before inserting the boards into the TPRNx4 subrack, make sure to set the RS485 address. It
must be different for Master and Slave subracks. Refer to TPRNx4 Installation Instruction for more
information on address setting.
TFLN TFLN TFLN TFLN TSRX TDTX500 TFLN TFLN TFLN TFLN
AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN
UL UL UL UL UL UL UL UL
= 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3
4
2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4
DL DL DL DL DL DL DL DL
UL DL UL DL UL DL UL DL UL DL UL DL UL DL UL DL
RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs
1 1 1 1 1 1 1 1
2 2 2 2
TDTX 2 2 2 2
3 3 3 3 3 3 3 3
TSRX
4 4 4 4 4 4 4 4
Slave Side
Carefully insert the TSRX-244/8 and the TDTX-300 boards into 2 adjacent slots in the middle of the Slave
subrack, so as to allow proper cabling of the TFLNs.
Lock the screws on the 4 corners of each board.
NOTE If the subrack hosts the Interconnect Link and more than 6 TFLNs make sure to provide proper
ventilation.
WARNING!
Only active TPRNx4 sub-rack can be used to house the Interconnect Link.
5
TFLN TFLN TFLN TFLN TSRX TDTX500 TFLN TFLN TFLN TFLN
AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN AUX MAIN
UL UL UL UL UL UL UL UL
= 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3 = 1 3
2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4
DL DL DL DL DL DL DL DL
UL DL UL DL UL DL UL DL UL DL UL DL UL DL UL DL
RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs RXs TXs
1 1 1 1 1 1 1 1
Slave Side
2 2 2 2 2 2 2 2
3 3 3 3 3 3 3 3
4 4 4 4 4 4 4 4
Use the shorter SMA-m jumper to connect the RF Out Port of the TSRX-244/8 board with the RF In Port
of the TDTX-300 board; use the SMB-f jumper to connect the 10.7 MHz ports of the two boards each
other.
7
Slave Side
DL Optical jum per UL Optical jum per
Remove the protection caps from the optical connectors of the TSRX-244/8 and TDTX-300 boards, clean the
fibres and plug in the SC-APC optical jumpers (not included) which allow a connection to the Master subrack.
WARNING!
For a correct system start-up, Remote
Units must be switched on before the
8
relevant Master Unit.
NOTE
Refer to TFLN Installation Instruction for proper discovery procedure
of the Slave subrack.
TO REMOVE ONE OF THE UNITS:
9
- Switch off the relevant TPRNx4 power supply, remove the fibres, insert the
caps
- Disconnect the RF jumpers
- Unscrew the 4 screws and slowly remove the card
- Put the card in its safety box
Warning
Class 1 laser product.
Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.