Professional Documents
Culture Documents
TDS 202 Dura Proof
TDS 202 Dura Proof
TDS 202 Dura Proof
Dura Proof
Acrylic Based, Flexible, Water proof Coating
AQUASEAL
Description Typical Properties
DURA PROOF is a single component, Properties l i s t e d are only for guidance and
elastomeric coating based on acrylic polymer. are not a guarantee of performance
Applied as a liquid, it cures to form a durable,
flexible, protective and waterproof membrane
with a high level of resistance to weathering
Technical Data & Physical Properties
agents like UV rays, sunlight, frost, rainfall, etc.
The product is designed for the protection of
Appearance: Liquid paste
concrete structures against carbonation and
chloride water ingress. DURA PROOF is also
Color Grey, White
suitable as a seamless and elastomeric
waterproofing coating for interior and exterior
Drying 6 Hours
applications.
/ Over coating
Features
Coverage 2.2 Kg/Sq. m
Highly elastic, durable and flexible
Single component, suitable for internal and
Density 1.2 gm./ cc
external applications
Strong adhesion to cementitious substrates
Application
Waterproofs and protects concrete from
Temperature 10°C - +50°C
waterborne salts
Excellent resistance to weathering agents
Service
such as UV, sunlight, rain, etc.
Temperature up to +90°C
Uses
Elongation
Protective coating on asphalt, metal,
@ Break 400 %
concrete and masonry roof surfaces to
control dampness and provide weatherproof
Toxicity Non Toxic
protection
Suitable for wet areas such as kitchens,
Chemical
bathrooms, locker rooms, shower rooms,
etc. where more flexibility is required Resistance: Resistant to spillage of petrol,
Bridge and highway structures, diesel, acids, alcohol, UV,
underpasses, car parking decks, multi-storey carbonation, and chloride ion
car parks diffusion
Marine environments
Protective membrane for polyurethane foam
installation Method to use
Surface Preparation
Coverage area should be clean, sound and free
of oil, grease, dust, dirt and other loose
particles. Metal surfaces should be rust free and
this can be achieved by wire brushing or grit
blasting. The surface may be damp but not
soaking wet. DURA PROOF can be applied with
an airless sprayer, brush, roller at temperatures
over 10°C.
Priming
A primer coat is required to seal the pores and
stabilize the surface. DURA PROOF diluted with
20% clean water should be used as a
202
Dura Proof
Acrylic Based, Flexible, Water proof Coating
AQUASEAL
primer coat. This will improve the bond strength Temperatures. In extreme tropical climate, the
of coating and can be applied by a brush, roller product must be stored in cooled ambience.
or spray Excessive humidity and over exposure to UV
will result in the reduction of shelf life. Stir
Application Procedure product well prior to use.
The primer coat should be allowed to dry
completely before the application of DURA Health & Safety
PROOF. The drying time should be a minimum DURA PROOF contains no hazardous
of 8 hours at 25°C. The product can be applied substances. As with all construction chemical
by brush or roller, but is probably best applied products, caution should always be exercised.
using an air less spray. Apply a minimum of two Protective clothing such as gloves and goggles
coats with undiluted material @1kg/m2 per coat. shall be worn whilst handling. Wearing long
It is important to ensure that each coat has to sleeve overall, safety shoes and face mask is
be cured totally before applying the next coat. recommended for maximum safety. Reseal all
Prior to second coat, a close visual inspection of containers after use and ensure product is
the surface should be made for any pin holes or stored as instructed on the safety section of the
surface irregularities. The second coat should labeling. Treat any splashes to the skin or eyes
be applied at 90° to the first, to ensure a full with fresh water immediately. Should any of the
unbroken coating to the substrate. For improved products be accidentally swallowed, do not
results, a glass fiber mat can be embedded into induce vomiting, but call for medical assistance
the first coat while it is wet on all corners and immediately. For more details, please refer to
other critical areas. the MSDS released on each Durabuild product.
Cleaning
Wet product should be removed from tools and
equipment with clean water immediately after
use. Cured material should be removed VER. 1.4.13
mechanically.
Limitations
Do not expose to moving water or rain during
application.
Technical information given in this data sheet is true and exact to the best of our knowledge. The data sheets are revised /updated regularly and it is important to ensure that the latest release is
used for reference and recommendation. All data provided is the result of numerous tests, assessment and analysis conducted under laboratory conditions. Climatic disparity in temperature,
humidity, etc., along with conditions of substrate, may alter the values.
(Durabuild is manufactured by AQUASEAL QATAR FACTORY WLL.)
PO Box 201019, Doha, Qatar. Telephone +974 44678826 - Fax +974 44506819
www.durabuild-qatar.com / info@aquaseal-qatar.com