Professional Documents
Culture Documents
Product Guide: Rough Terrain Hydraulic Crane
Product Guide: Rough Terrain Hydraulic Crane
Product Guide
Features
n
MAX. CAPACITY (Outriggers) - 30.0 Tonnes at n
BOOM - 4 Sec 8.8m - 29.0m
3m Radius (85% Rating) 360° Slew n
MAXIMUM ROAD SPEED - 35 km/hr
n
MAX. CAPACITY (On Tyres) - 13.65 Tonnes at n
CARRIER - 4 X 4 Wheel Drive with 4 Wheel steer
3m Radius (85% Rating) over front
Superstructure Specification
Load (Te) 30.0 28.0 24.5 20.5 17.0 12.7 8.7 4.2
No. of fall 8 7 6 5 4 3 2 1
Main Boom Duties on Outriggers Fully Extended 7.9m – 13.7m Tele. Swingaway
Through Full 360º Slew Boom Extension On Outriggers
Radius
Fully Extended - 360º
Main Boom Length in Meters
(in
Meters) 8.8 12.2 15.2 18.3 21.3 24.4 27.4 29.0 Radius **7.9m Length 13.7m Length
30,000 22,700 21,275 (in 0° 30° 0° 30°
3 Meters)
(61) (70) (74.5) offset offset offset offset
25,650 22,700 20,625 *3,715
3.5 9
(57) (67.5) (72.5) (76)
22,775 21,050 19,725 *17,600 3,715 *2,380
4 10
(53) (64.5) (70.5) (76) (75) (76)
19,850 20,000 18,750 16,350 *13,350
4.5 3,715 *2,620 2,380
(48.5) (62) (68.5) (72.5) (76) 12
(71.5) (76) (75.5)
17,875 18,300 17,125 15,500 13,100 *10,175
5 3,615 2,585 2,205
(43.5) (59) (66) (71) (74) (76) 14
(68) (73) (72.5)
14,250 14,700 14,775 13,550 12,425 10,175 *8,410
6 3,110 2,290 1,970 *1,235
(31.5) (53.5) (62) (67.5) (71) (74) (76) 16
(64.5) (69.5) (69.5) (76)
12,300 12,500 11,900 11,250 9,330 7,870 *7,030
7
(47) (57.5) (64) (68) (71.5) (74) (76) 2,630 1,985 1,785 1,235
18
10,300 10,500 10,375 10,075 8,465 7,245 6,700 (61) (65.5) (66.5) (75)
8
(39.5) (52.5) (60) (65) (69) (72) (73) 2,150 1,735 1,685 1,230
20
8,750 8,955 9,055 9,040 7,755 6,630 6,075 (57) (62) (63.5) (71.5)
9
(30.5) (47.5) (56.5) (62) (66) (69.5) (71) 1,800 1,540 1,605 1,155
22
7,530 7,785 7,925 7,970 7,145 6,100 5,555 (53.5) (58) (60.5) (68.5)
10
(17) (42) (52.5) (59) (63.5) (67.5) (69) 1,465 1,385 1,495 1,120
5,960 6,065 6,075 6,095 5,085 4,620 24
12 (49) (53.5) (57) (65)
(27.5) (43.5) (52) (58) (62.5) (64.5)
1,130 1,250 1,375 1,095
4,580 4,590 4,610 4,295 4,020 26
14 (44.5) (48.5) (54) (61.5)
(32.5) (44.5) (52) (57.5) (60)
865 1,015 1,225 1,080
3,545 3,565 3,580 3,605 3,420 28
16 (39.5) (43.5) (50) (57.5)
(15) (36) (45.5) (52.5) (55)
660 770 1,000 1,055
2,815 2,830 2,850 2,865 30
18 (34) (37.5) (46.5) (53.5)
(24) (38) (46.5) (50)
2,255 2,265 2,290 790 905
20 32
(29) (40) (44) (42) (49)
1,795 1,820 1,830 610 670
22 34
(14.5) (32.5) (37.5) (37.5) (43.5)
1,455 1,465 Note : ( ) Boom angles are in degrees.
24
(22.5) (30) * This capacity is based upon the maximum boom angle.
1,160 **7.9m capacities also applicable to fixed length off settable
26
(19) swingaway
Note : ( ) Boom angles are in degrees. * This capacity is based upon the maximum boom angle.
Notes for Lifting Capacities 8. Tyres shall be inflated to the recommended pressure before lifting on rubber.
WARNING: THIS CHART IS ONLY A GUIDE. The notes below are for illustration Capacities must be reduced for lower tyre inflation. Damaged tyre is hazardous for
only and should not be relied upon to operate the crane. The individual crane’s safe operation of crane.
load chart, operating instructions and other instruction plates must be read & 9. Unless otherwise stated, capacities are with powered boom sections, extended
understood prior to operating the crane. equally at all times.
1. All rated loads have been tested to and meet minimum requirements of IS: 4573- 10. Defined Arc ± 6° on either side of longitudinal centerline of machine.
1982 Specification for Power Driven Mobile Cranes, and do not exceed 85% of the 11. For Pick & Carry operation, boom must be centered over front of machine, mechanical
tipping load on outriggers (85% of the tipping load on rubber) as determined by swing lock engaged and load restrained from swinging. When handling loads in the
SAE J765 OCT80 Crane Stability Test Code. structural range with capacities close to maximum rating, travel should be reduced to
2. The weight of hookblock, slings and all similarly used load handling devices must creep speeds (not over 61m of movement in 30 min, not exceeding 1.6 KPH).
be added to the weight of the load. When more than minimum required reeving is 12. Axle lockouts must be functioning before lifting on rubber.
used, the additional rope weight shall be considered part of the load.
13. 7.9m & 13.7m boom extension lengths may be used for single line lifting service.
3. Capacities appearing above the bold line are based on structural strength and
tipping should not be relied upon as a capacity limitation. 14. Radii listed are for a fully extended boom with the boom extension erected. For main
boom lengths less than fully extended, the rated loads are determined by boom
4. All capacities are for crane on firm, level surface. It may be necessary to have angle. Use only the column which corresponds to the boom extension length and
structural supports under the outrigger floats or tyres to spread the load, to a larger offset for which the machine is configured. For boom angles not shown, use the
bearing surface. rating of the next lower boom angle.
RT 630C
5. When either boom length or radius or both are between values listed, the smallest 15. With tele boom extension in working position and main boom length greater than
load shown at either the next larger radius or boom length shall be used. 18.3m, the boom angle must not be less than 30°, since loss of stability will occur
6. For outrigger operation, all outriggers shall be extended fully & tires raised free of causing a tipping condition.
the ground before raising boom or lifting loads. WARNING: Operation of this machine with heavier load than the capacities listed is
7. On rubber, lifting with boom extensions is not permitted. strictly prohibited. Machine tipping occurs rapidly without any advance warning.
20.5x25-24PR (Stationary–Defined Arc Over Front) (Pick & Carry Duties – 4.0 km/hr Over Front)
Main Boom Length in Meters Main Boom Length in Meters
Radius Radius
Tyre Pressure – 5.27kg/cm2 Tyre Pressure – 5.27kg/cm2
(in Meters) (in Meters)
8.8 12.2 15.2 18.3 8.8 12.2 15.2 18.3
13,650 12,025 7,460 11,725 11,725 8,275
3 3
(61) (70) (74.5) (61) (70) (74.5)
12,425 10,025 7,460 10,500 10,500 8,275
3.5 3.5
(57) (67.5) (72.5) (57) (67.5) (72.5)
11,225 10,025 7,460 9,385 9,385 8,275
4 4
(53) (64.5) (70.5) (53) (64.5) (70.5)
10,175 10,025 7,460 7,460 8,415 8,415 8,275 6,050
4.5 4.5
(48.5) (62) (68.5) (72.5) (48.5) (62) (68.5) (72.5)
9,225 9,225 7,460 7,460 7,565 7,565 7,565 6,050
5 5
(43.5) (59) (66) (71) (43.5) (59) (66) (71)
7,610 7,610 7,460 7,460 6,190 6,190 6,190 6,050
6 6
(31.5) (53.5) (62) (67.5) (31.5) (53.5) (62) (67.5)
6,005 6,005 6,005 5,180 5,180 5,180
7 7
(47) (57.5) (64) (47) (57.5) (64)
5,125 5,125 5,125 4,430 4,430 4,430
8 8
(39.5) (52.5) (60) (39.5) (52.5) (60)
4,260 4,260 4,260 3,820 3,820 3,820
9 9
(30.5) (47.5) (56.5) (30.5) (47.5) (56.5)
3,535 3,535 3,535 3,315 3,315 3,315
10 10
(17) (42) (52.5) (17) (42) (52.5)
2,505 2,505 2,505 2,505
12 12
(27.5) (43.5) (27.5) (43.5)
1,705 1,265
14 14
(32.5) (32.5)
1,210 885
16 16
(15) (15)
Note : ( ) Boom angles are in degrees. Note : ( ) Boom angles are in degrees.
AXLES
Front: Drive-steer with differential and planetary
RT 630C
Auxiliary Hoist
(Optional)
Auxiliary
Boom Nose (Optional)
Lattice (Optional)
Auxiliary Hoist
(Optional)
Dimensions in mm
Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without notice. The
photographs/drawings in this document are just for Illustrative purpose which may include optional items and accessories, which can be provided at an
RT 630C
CHENNAI
TIL Limited
Jhaver Plaza, 7th Floor 1-A
Nungambakkam High Road
Chennai 600 034, Tamil Nadu
Phone: +91 044 6670 3000 / 3010
Fax: +91 44 2827 9681
Email: chennai.til@tilindia.com
DELHI NCR
Plot 11, Site No.IV
Sahibabad Industrial Area
Ghaziabad 201 010 U.P.
Phone: +91 120 277 8735 / 8736 / 7468
Fax: +91 120 277 7467
Email: MHGMarketing.Sahibabad@tilindia.com | mhgcs.Sahibabad@tilindia.com
DELHI
TIL Limited
302 Ansal Bhawan
16, Kasturba Gandhi Marg, New Delhi 110 001
Phone: +91 11 2331 1607 / 8046 / 9248 | 2335 0250 / 0255
Fax: +91 11 2331 3263
Email: til.delhi@tilindia.com
KAMARHATTY
TIL Limited
517, Barrackpore Trunk Road
Kolkata 700 058
Phone: +91 33 2553 1352 / 1882 | 6633 4000
Fax: +91 33 2553 2546 / 5971
Email: MktDept.KMT@tilindia.com | til.kmt@tilindia.com
KHARAGPUR
TIL Limited
Vill. & P.O. Changual, Kharagpur
Dist: Paschim Medinipur 721 301, West Bengal
Phone: +91 32 2266 1101
TIL has a pan-India network of offices with service
engineers located in the close proximity of jobsites.
MUMBAI
TIL Limited
A - 606, A Wing, 6th Floor,
215 Atrium, Andheri - Kurla Road,
Toll Free No: 1800 266 1535
Andheri (East), Mumbai 400059, Maharashtra
Phone: + 91 22 4969 1169 www.tilindia.in
Mobile: +91 8850971609
Email: Mumbai.TIL@tilindia.com | Mumbai.Custsupp@tilindia.com Technical Specification TIL/RT630C/0818. This cancels Technical Specification TIL/RT630C/1117
This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment,
and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.
Copyright © 2017 TIL Limited. All Rights Reserved