Professional Documents
Culture Documents
Airbus SB A320-46-1088 R15 Dated 09.apr.2021
Airbus SB A320-46-1088 R15 Dated 09.apr.2021
SERVICE BULLETIN
CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.
ATA SYSTEM: 46
SUMMARY
APPLICABILITY Operators updated.
PLANNING INFORMATION
APPLICABILITY Scrapped aircraft MSN 01006 removed.
CONF 002
SUMMARY
APPLICABILITY Operators updated.
PLANNING INFORMATION
APPLICABILITY Scrapped aircraft MSN 01006 removed.
CONF 003
SUMMARY
APPLICABILITY Operators updated.
CONCURRENT REQUIREMENTS Applicability updated.
PLANNING INFORMATION
APPLICABILITY Scrapped aircraft MSN 01006 removed.
Configuration definition Aircraft added.
CONCURRENT REQUIREMENTS Applicability updated.
CONF 004
SUMMARY
APPLICABILITY Operators updated.
CONCURRENT REQUIREMENTS Concurrent requirements added.
PLANNING INFORMATION
APPLICABILITY Scrapped aircraft MSN 01006 removed.
Configuration definition Aircraft added.
CONCURRENT REQUIREMENTS Concurrent requirements added.
SUMMARY
APPLICABILITY Operators updated.
PLANNING INFORMATION
APPLICABILITY Scrapped aircraft MSN 01006 removed.
CONF ALL
D. FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete
document. Replace the complete document.
Put this Revision Transmittal Sheet in front of the Service Bulletin.
E. HISTORY OF PREVIOUS REVISIONS
Revision No. 01 issued to add aircraft for operators 95V, AAF, ABY, AEE, ASL, FHY, GMI, HKJ,
IAW, LJB, MEA, MON, PAL, TAP and THY.
Revision No. 02 issued to add aircraft for operators 48P, 52T, ASL, AVA, BEC, BER, BHP, CBJ,
CCM, CES, FHY, RZO, SDM, SVW, TAI, TCX and VLG.
Revision No. 03 issued to add aircraft MSN 1004 for operator HFY, aircraft MSN 1795 and
2507 for operator G4I, aircraft MSN 2165 for operator 74T, aircraft MSN 2921 for operator
SVW, aircraft MSN 3238 for operator KNE and aircraft MSN 4353 for operator MJF and also
to remove aircraft MSN 1598 and 1625 for operator TAI and aircraft MSN 2066 for operator
AVA.
Revision No. 03 issued to remove Service Bulletin 22-1353 from the list of the concurrent
Service Bulletins to be accomplished for aircraft MSN 1006.
Revision No. 04 issued to:
Add aircraft MSN 1589 for operator 15S and aircraft MSN 4199 for operator 95W
Remove aircraft MSN 3033, 3066, 3074, 3162 and 3316 from the Service Bulletin effectivity.
Revision No. 05 issued to add:
Aircraft MSN 2566 for operator ORF
Aircraft MSN 2748 for operator 80X
Aircraft MSN 3540, 3594 and 3908 for operator TAM
Aircraft MSN 4228 for operator HKJ.
Revision No. 06 issued to add aircraft MSN 6465 for operator PGT.
Revision No. 07 issued to add aircraft MSN 1999 for operator SND.
Revision No. 08 issued to add aircraft MSN 3451 for operator JBU.
Revision No. 09 issued to add aircraft MSN 3479 for operator JBU.
Revision No. 10 issued to add aircraft for operators BEL and SVR.
Revision No. 11 issued to add aircraft MSNs 6347, 6467, 6494, 6529, 6622, 6646, 6717 and
6811 for operator QTR.
Revision No. 12 issued to add:
MODIFICATION CLASSIFICATION
MAJOR 31442P6830
MINOR 151451P6062 151451P7346 151451P7350 151451P8893 153972P13136
155918P14116 36344P9610 38198P9842
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF 002
MODIFICATION CLASSIFICATION
MAJOR 31442P6830
MINOR 151451P6062 151451P7346 151451P7350 151451P8893 153972P13136
155918P14116 36344P9610 38198P9842
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF 003
MODIFICATION CLASSIFICATION
MAJOR 31442P6830
MINOR 151451P6062 151451P7346 151451P7350 151451P8893 153972P13136
155918P14116 38198P9842
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF 004
MODIFICATION CLASSIFICATION
MAJOR 31442P6830
MINOR 151451P6062 151451P7346 151451P7350 151451P8893 153972P13136
155918P14116 38198P9842
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
MODIFICATION CLASSIFICATION
MAJOR 31442P6830
MINOR 151451P6062 151451P7346 151451P7350 151451P8893 153972P13136
155918P14116 38198P9842
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
CONF ALL
B. REASON
(1) History
This Service Bulletin is issued further to an operator's request.
(2) Objective/Action
This Service Bulletin consists in the:
EVALUATION TABLE
COMPLIANCE OPTIONAL COST SAVING NO
A/C OPERATION NO VENDOR SB NO
AFFECTED
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD NO
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
D. MAINTENANCE CONFIGURATION
CONF 002
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
CONF 003
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
CONF 005
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
11K 15S 39K 39V 41N 48P 51L 55S 60X 80X 82W 83V 86Z 87Z 95V 95W AAR AAY AEE AIJ
ARU ASA ASL ASV AUH AWC BAW BDJ BEC BEL BKP BWJ CCM CEB DCS EDW ELB EVA EWG
EXV EZY F2I FHM FHY G4I G8E GJW GOW GSH GSW GWI HFY HKJ IAW IGO IRA IYE IZG JBU
KNE LDA LDM MJF MLM MSC MSR MYX NIA NVD NWC ORF PGT QTR RJA RSD RZO SDM SDR
SEH SND SVR SVW TAP TCI UNA VAW VLG VOE VOI
NOTE: This Service Bulletin is written for the operators listed above. The modification in
this Service Bulletin can be done by other operators. If other operators want to do
this modification, use the RFC/RMO procedure and write to:
AIRBUS
2 ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
G. CONCURRENT REQUIREMENTS
ON A/C 01004
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01125, 01130, 01140, 01159, 01198, 01200, 01208, 01221, 01238, 01250, 01379,
01396, 01413, 01430, 01461, 01482, 01509, 01550, 01571, 01578, 01603, 01605, 01613,
01637, 01654, 01657, 01663, 01672, 01679, 01690, 01711, 01717, 01753, 01767, 01771,
01775, 01804, 01823, 01889, 01977, 02055
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01422
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 01589
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01599, 02192, 02403, 02507, 02566, 02592, 02748, 02921, 03133, 03379
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01795
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 01841, 01884, 01896, 01901, 01929, 01966, 01988, 02011, 02070, 02073, 02079,
02094, 02102
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01999
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02098, 02166, 02186, 02188, 02190, 02194, 02241, 02277, 02296, 02335, 02349,
02362, 02388, 02389, 02407, 02429, 02441, 02465, 02497, 02553, 02562, 02587, 02591,
02606, 02610, 02627, 02653, 02707, 02751, 02761, 02785, 02791, 02792, 02794, 02798,
02799, 02822, 02879, 02913, 02930, 02964, 03044, 03252, 03317
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02108
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02165
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1148 (AUTO FLIGHT - INSTALL THALES MCDU
PN C19266AA01 COMPATIBLE WITH FMS2 (CFM ENGINES)).
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 02466, 02619-02621, 02645, 02658, 02694, 02697, 02720, 02804, 02916, 02919,
02925, 02968, 02981, 03025, 03049, 03107, 03302, 03322, 03365, 03392, 03422, 03423,
03439, 03444, 03462, 03476, 03492, 03512, 03516, 03527, 03589, 03626, 03709, 03714,
03748, 03753, 03773, 03785, 03802, 03812, 03818, 03820, 03829, 03840, 03850, 03852,
03878, 03882, 03905, 03907, 03925, 03926, 03952, 03990, 04044, 04061, 04065, 04067,
04094, 04243, 04310, 05879, 05902
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03199, 03238, 03513, 03547, 03617, 03632, 03886, 03985, 04169, 04199, 04228,
04353, 04428, 04503, 04583, 04878
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03479
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03540, 03594, 03895, 03900, 03908, 03915, 05055, 05350, 05382, 05675, 05990,
06347, 06465, 06467, 06494, 06529, 06622, 06646, 06717, 06811, 09456, 09507
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03767, 03911, 04024, 04535, 04609, 04614, 04870, 05933, 06749, 07523, 07576,
07581, 07939, 07945, 08008, 08970, 09056, 09512, 09524
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03069
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1258 (AUTO FLIGHT - MCDU - INSTALL THALES
MCDU PN C19266DA01 COMPATIBLE WITH FMS2).
ON A/C 03374
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1353 (AUTO FLIGHT - MCDU - INSTALL THALES
MCDU PN C19266EA01 COMPATIBLE WITH FMS2).
CONF ALL
H. NATURE OF THE WORK
CONF 001
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT YES
CONF 002
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT YES
CONF 003
(1) Modification
AIRCRAFT YES
EQUIPMENT YES
CONF 004
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT YES
CONF 005
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT YES
CONF ALL
I. MANPOWER
CONF 001
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 002
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 003
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 004
(1) Modification
MANPOWER
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 005
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
Z210
FR24
A
Z120
FR12
FR4 FR8
FR1
A
VIEW LOOKING FWD
ICN-A320-A-46XX1088-A-FAPE3-00HZD-A-003-01
ATA SYSTEM: 46
MSN CONFIGURATION
00649 01004 01014 01125 01130 01140 01159 01177 01198 001
01200 01208 01221 01238 01250 01379 01396 01413 01418
01422 01424 01430 01461 01482 01509 01550 01571 01578
01579 01603 01605 01613 01637 01654 01657 01663 01672
01679 01690 01711 01717 01753 01759 01767 01771 01775
01803 01804 01823 01841 01884 01889 01896 01901 01929
01966 01977 01987 01988 02011 02030 02055 02070 02073
02079 02094 02098 02102 02166 02186 02188 02190 02194
02241 02260 02277 02296 02335 02349 02362 02376 02388
02389 02407 02429 02441 02465 02466 02497 02553 02562
02587 02591 02606 02610 02616 02619 02620 02621 02627
02645 02653 02656 02658 02694 02697 02707 02720 02740
02751 02761 02785 02791 02792 02794 02798 02799 02804
02822 02862 02879 02913 02916 02919 02925 02930 02964
MSN CONFIGURATION
02968 02981 03025 03044 03049 03107 03252 03302 03317
03322 03365 03392 03422 03423 03439 03444 03462 03476
03492 03512 03516 03527 03540 03589
CONF 002
MSN CONFIGURATION
03594 03626 03709 03714 03748 03753 03773 03785 03802 002
03812 03818 03820 03829 03840 03850 03852 03878 03882
03895 03900 03905 03907 03908 03915 03925 03926 03952
03990 04044 04061 04065 04067 04094 04243 04310 05055
05350 05382 05675 05879 05902 05990 06347 06465 06467
06494 06529 06622 06646 06717 06811 09456 09507
CONF 003
MSN CONFIGURATION
03617 03632 03767 03886 03911 03985 04024 04169 04199 003
04228 04353 04428 04503 04535 04583 04609 04614 04870
04878 05933 06749 07523 07576 07581 07939 07945 08008
08970 09056
CONF 004
MSN CONFIGURATION
01589 01599 01795 01999 02108 02165 02192 02403 02507 004
02566 02592 02748 02921 03069 03133 03199 03238 03374
03379 03479 03513 03547
CONF 005
MSN CONFIGURATION
09512 09524 005
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 regards the specific PRE-SB status of the related aircraft.
CONF 001 retrofits following modifications: 151451P6062, 151451P7346,
151451P7350, 151451P8893, 153972P13136, 155918P14116, 31442P6830,
36344P9610, 38198P9842.
CONF 002
Configuration 002
CONF 002 regards the specific PRE-SB status of the related aircraft.
CONF 003
Configuration 003
CONF 003 regards the specific PRE-SB status of the related aircraft.
CONF 003 retrofits following modifications: 151451P6062, 151451P7346,
151451P7350, 151451P8893, 153972P13136, 155918P14116, 31442P6830,
38198P9842.
CONF 004
Configuration 004
CONF 004 regards the specific PRE-SB status of the related aircraft.
CONF 004 retrofits following modifications: 151451P6062, 151451P7346,
151451P7350, 151451P8893, 153972P13136, 155918P14116, 31442P6830,
38198P9842.
CONF 005
Configuration 005
CONF 005 regards the specific PRE-SB status of the related aircraft.
CONF 005 retrofits following modifications: 151451P6062, 151451P7346,
151451P7350, 151451P8893, 153972P13136, 155918P14116, 31442P6830,
38198P9842.
CONF ALL
B. CONCURRENT REQUIREMENTS
ON A/C 01004
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01125, 01130, 01140, 01159, 01198, 01200, 01208, 01221, 01238, 01250, 01379,
01396, 01413, 01430, 01461, 01482, 01509, 01550, 01571, 01578, 01603, 01605, 01613,
01637, 01654, 01657, 01663, 01672, 01679, 01690, 01711, 01717, 01753, 01767, 01771,
01775, 01804, 01823, 01889, 01977, 02055
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01422
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 01589
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01599, 02192, 02403, 02507, 02566, 02592, 02748, 02921, 03133, 03379
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01795
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 01841, 01884, 01896, 01901, 01929, 01966, 01988, 02011, 02070, 02073, 02079,
02094, 02102
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 01999
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02098, 02166, 02186, 02188, 02190, 02194, 02241, 02277, 02296, 02335, 02349,
02362, 02388, 02389, 02407, 02429, 02441, 02465, 02497, 02553, 02562, 02587, 02591,
02606, 02610, 02627, 02653, 02707, 02751, 02761, 02785, 02791, 02792, 02794, 02798,
02799, 02822, 02879, 02913, 02930, 02964, 03044, 03252, 03317
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02108
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 02165
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1148 (AUTO FLIGHT - INSTALL THALES MCDU
PN C19266AA01 COMPATIBLE WITH FMS2 (CFM ENGINES)).
NOTE: Service Bulletin No. Ref. SB A320-46-1101 (INFORMATION SYSTEM - ATIMS - INSTALL
ATSU CSB8.3/HW-A10 WITH FANS B+ APPLICATIONS AND WITH VDL MODE 2
ACTIVATED).
ON A/C 02466, 02619-02621, 02645, 02658, 02694, 02697, 02720, 02804, 02916, 02919,
02925, 02968, 02981, 03025, 03049, 03107, 03302, 03322, 03365, 03392, 03422, 03423,
03439, 03444, 03462, 03476, 03492, 03512, 03516, 03527, 03589, 03626, 03709, 03714,
03748, 03753, 03773, 03785, 03802, 03812, 03818, 03820, 03829, 03840, 03850, 03852,
03878, 03882, 03905, 03907, 03925, 03926, 03952, 03990, 04044, 04061, 04065, 04067,
04094, 04243, 04310, 05879, 05902
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03199, 03238, 03513, 03547, 03617, 03632, 03886, 03985, 04169, 04199, 04228,
04353, 04428, 04503, 04583, 04878
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03479
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03540, 03594, 03895, 03900, 03908, 03915, 05055, 05350, 05382, 05675, 05990,
06347, 06465, 06467, 06494, 06529, 06622, 06646, 06717, 06811, 09456, 09507
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03767, 03911, 04024, 04535, 04609, 04614, 04870, 05933, 06749, 07523, 07576,
07581, 07939, 07945, 08008, 08970, 09056, 09512, 09524
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
ON A/C 03069
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1258 (AUTO FLIGHT - MCDU - INSTALL THALES
MCDU PN C19266DA01 COMPATIBLE WITH FMS2).
ON A/C 03374
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):
NOTE: Service Bulletin No. Ref. SB A320-22-1353 (AUTO FLIGHT - MCDU - INSTALL THALES
MCDU PN C19266EA01 COMPATIBLE WITH FMS2).
CONF ALL
C. REASON
(1) History
This Service Bulletin is issued further to an operator's request.
(2) Objective/Action
This Service Bulletin consists in the:
(3) Advantages
Accomplishment of this Service Bulletin will satisfy the operator's request.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
CONF 001 004
1 Modify the Equipment and the Wiring in the Cockpit
CONF 002 003 005
1 Modify the Equipment and the Wiring in the Cockpit
CONF 001-004
2 Remove the Safety Clips from Rear Circuit Breaker Panel 121VU
CONF 005
2 Remove the Safety Clips from Rear Circuit Breaker Panel 121VU
CONF ALL
3 Modify the Wiring in the Avionics Compartment
E. COMPLIANCE
(1) Classification
OPTIONAL: Service Bulletin for convenience or option.
(2) Accomplishment Timescale
In accordance with operators' maintenance schedule.
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
PREPARATION
Job Set-up 0.50 h
Parity Configuration Recording 0.50 h
PROCEDURE
Modify the Equipment and the Wiring in the Cockpit 2.00 h
Remove the Safety Clips from Rear Circuit Breaker Panel 0.50 h
121VU
Modify the Wiring in the Avionics Compartment 3.00 h
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Test 0.50 h
CLOSE-UP
Close-up 1.00 h
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
PREPARATION
Job Set-up 0.50 h
Parity Configuration Recording 0.50 h
PROCEDURE
Modify the Equipment and the Wiring in the Cockpit 2.00 h
Remove the Safety Clips from Rear Circuit Breaker Panel 0.50 h
121VU
Modify the Wiring in the Avionics Compartment 3.00 h
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Test 0.50 h
CLOSE-UP
Close-up 1.00 h
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
PREPARATION
Job Set-up 0.50 h
Parity Configuration Recording 0.50 h
PROCEDURE
Modify the Equipment and the Wiring in the Cockpit 2.00 h
Remove the Safety Clips from Rear Circuit Breaker Panel 0.50 h
121VU
Modify the Wiring in the Avionics Compartment 3.00 h
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Test 0.50 h
CLOSE-UP
Close-up 1.00 h
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 004
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
PREPARATION
Job Set-up 0.50 h
Parity Configuration Recording 0.50 h
PROCEDURE
Modify the Equipment and the Wiring in the Cockpit 2.00 h
Remove the Safety Clips from Rear Circuit Breaker Panel 0.50 h
121VU
Modify the Wiring in the Avionics Compartment 3.00 h
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Test 0.50 h
CLOSE-UP
Close-up 1.00 h
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF 005
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-46-XX-1088-01000-93AA-A Modification
PREPARATION
Job Set-up 0.50 h
Parity Configuration Recording 0.50 h
PROCEDURE
Modify the Equipment and the Wiring in the Cockpit 2.00 h
Remove the Safety Clips from Rear Circuit Breaker Panel 0.50 h
121VU
Modify the Wiring in the Avionics Compartment 3.00 h
PREPARATION FOR TEST
Job Set-up 0.50 h
TEST
Test 0.50 h
CLOSE-UP
Close-up 1.00 h
TOTAL MAN-HOURS 8.50 h
ELAPSED TIME (HOURS) 8.50 h
CONF ALL
H. WEIGHT AND BALANCE
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. The definition of
MEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.
Manufacturer's Empty Weight +4.000 kg (+8.818 lb)
Effect on Balance +17.200 kg.m (+124.408 lb.ft)
I. ELECTRICAL LOAD DATA
ON A/C 01125, 01130, 01140, 01159, 01198, 01200, 01208, 01221, 01238, 01250, 01379,
01396, 01413, 01430, 01461, 01482, 01509, 01550, 01571, 01578, 01603, 01605, 01613,
01637, 01654, 01657, 01663, 01672, 01679, 01690, 01711, 01717, 01753, 01767, 01771,
01775, 01804, 01823, 01889, 01977, 02055
ON A/C 03540, 03594, 03895, 03900, 03908, 03915, 05055, 05350, 05382, 05675, 05990,
06347, 06465, 06467, 06494, 06529, 06622, 06646, 06717, 06811, 09456, 09507
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A320-A-46-XX-1088-01000-93AA-A Modification
C. CONSUMABLES
CONF 001
Referenced consumables for task set A320-A-46-XX-1088-01000-93AA-A
Modification
To accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM Task 20-21-15-912-001
Ref. AMM Task 25-54-11-400-001
Ref. AMM Task 11-00-00-400-003
CONF 002
Referenced consumables for task set A320-A-46-XX-1088-01000-93AA-A
Modification
To accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM Task 20-21-15-912-001
Ref. AMM Task 25-54-11-400-001
Ref. AMM Task 11-00-00-400-003
CONF 003
Referenced consumables for task set A320-A-46-XX-1088-01000-93AA-A
Modification
To accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM Task 20-21-15-912-001
Ref. AMM Task 25-54-11-400-001
Ref. AMM Task 11-00-00-400-003
CONF 004
Referenced consumables for task set A320-A-46-XX-1088-01000-93AA-A
Modification
To accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM Task 20-21-15-912-001
Ref. AMM Task 25-54-11-400-001
Ref. AMM Task 11-00-00-400-003
CONF 005
Referenced consumables for task set A320-A-46-XX-1088-01000-93AA-A
Modification
To accomplish this Service Bulletin it is necessary to use the consumable materials listed in:
Ref. AMM Task 20-21-15-912-001
Ref. AMM Task 25-54-11-400-001
Ref. AMM Task 11-00-00-400-003
CONF ALL
D. LIST OF NEW PARTS
Part kit 461088A01R01
Availability
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Procurement address
NOTE(S)
The AIRBUS material is included in the commercial offer and as such will be supplied
by AIRBUS Upgrade Services. To facilitate the material reception, Airline Customers
are requested to contact:
Procurement address
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Equipment procurement conditions are defined in the commercial offer. For any
assistance, Airline Customers are requested to contact:
Procurement address
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Equipment procurement conditions are defined in the commercial offer. For any
assistance, Airline Customers are requested to contact:
Procurement address
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Equipment procurement conditions are defined in the commercial offer. For any
assistance, Airline Customers are requested to contact:
Procurement address
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Equipment procurement conditions are defined in the commercial offer. For any
assistance, Airline Customers are requested to contact:
Procurement address
NOTE(S)
Sales terms must be agreed between the Customer and AIRBUS in accordance with
the RFC (or RFC/RMO) procedure.
Equipment procurement conditions are defined in the commercial offer. For any
assistance, Airline Customers are requested to contact:
CONF ALL
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A320-A-46-XX-1088-01000-93AA-A (A320-A-46-XX-1088-01ZZZ-93AZ-A)
Modification
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.
CONF 001
ELAPSED TIME (HOURS) 8.50 h
CONF 002
ELAPSED TIME (HOURS) 8.50 h
CONF 003
ELAPSED TIME (HOURS) 8.50 h
CONF 004
ELAPSED TIME (HOURS) 8.50 h
CONF 005
ELAPSED TIME (HOURS) 8.50 h
CONF ALL
B. PREPARATION
(1) Task A320-A-46-XX-1088-01001-540A-A (A320-A-46-XX-1088-01ZZZ-540Z-A)
Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
Task 12-34-24-869-002
Task 20-16-00-912-001
Task 22-82-12-000-001
AMM 24-50-00
Task 25-54-11-000-001
Task 31-53-34-000-001
Task 46-21-34-000-001
A320-28-1080
A320-28-1112
SB
A320-28-1176
A320-28-1185
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.
(b) Remove the partition panels (Panel 131CW, Panel 131DW and Panel 132EW)
from the FWD cargo compartment, at Frame 24A for access, refer to Ref. AMM
Task 25-54-11-000-001.
(c) Open, safety/lock and tag this (these) circuit breaker(s):
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00.
NOTE: For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-
912-001.
(d) Do the job set-up procedure as specified in the removal of the FWCs (FIN 1WW1
and FIN 1WW2), refer to Ref. AMM Task 31-53-34-000-001.
(e) Do the job set-up procedure as specified in the removal of ATSU-1 (FIN 1TX1),
refer to Ref. AMM Task 46-21-34-000-001.
(f) Do the job set-up procedure as specified in the removal of the MCDUs (FIN 3CA1,
FIN 3CA2 and, if installed FIN 3CA3) refer to Ref. AMM Task 22-82-12-000-001.
NOTE: For the aircraft with ACT6 installed for access, remove/install ACT6 in
accordance with Service Bulletin No. Ref. SB A320-28-1112 (FUEL -
TANKS - REMOVAL/INSTALLATION OF ADDITIONAL CENTER TANKS OF
OPERATING SEQUENCE B ON A319CJ) or Ref. SB A320-28-1176 (FUEL -
TANKS - FLEXIBILITY TO FIT ZERO TO SIX ACTS WITH ALTERNATE FUEL
SUPPLY SEQUENCE B) or Service Bulletin No. Ref. SB A320-28-1080
(FUEL - TANKS - REMOVAL/INSTALLATION OF ADDITIONAL CENTER TANK)
or Ref. SB A320-28-1185 (FUEL - TANKS - INSTALL ONE ACT PROVISION
ON A320 WITH CLS).
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Procedure
(a) For ATSU-1 (FIN 1TX1) wiring parity, before disconnection, record the figure
number of the hook-up chart on which line 1 agrees with the aircraft wiring
configuration, refer to Ref. Fig. HE and Ref. Fig. HF.
(b) For FWC-1 (FIN 1WW1) wiring parity, before disconnection, record the figure
number of the hook-up chart on which line 1 agrees with the aircraft wiring
configuration, refer to Ref. Fig. HH, and Ref. Fig. HI.
(c) For FWC-2 (FIN 1WW2) wiring parity, before disconnection, record the figure
number of the hook-up chart on which line 1 agrees with the aircraft wiring
configuration, refer to Ref. Fig. HJ and Ref. Fig. HK.
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 81VU 1813VT 16D 4621-0043 2M CF24 81VU 1TX1-AB 14K M1O (2)
2 81VU 1813VT 18D EN3155-016M2222 4621-0043 2M CF24 81VU 1TX1-AB 14K M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 81VU 1813VT 18D 4621-0043 2M CF24 81VU 1TX1-AB 14K M1O (2)
2 81VU 1813VT 16D EN3155-016M2222 4621-0043 2M CF24 81VU 1TX1-AB 14K M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 85VU 1851VT 61A 3152-0785 1S CF24 85VU 1WW1-AD 10A M1O (2)
2 85VU 1851VT 59A EN3155-016M2222 3152-0785 1S CF24 85VU 1WW1-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 85VU 1851VT 59A 3152-0785 1S CF24 85VU 1WW1-AD 10A M1O (2)
2 85VU 1851VT 61A EN3155-016M2222 3152-0785 1S CF24 85VU 1WW1-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 86VU 1860VT 10A 3152-0772 2S CF24 86VU 1WW2-AD 10A M1O (2)
2 86VU 1860VT 8A EN3155-016M2222 3152-0772 2S CF24 86VU 1WW2-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
2 86VU 1860VT 10A EN3155-016M2222 3152-0772 2S CF24 86VU 1WW2-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
C. PROCEDURE
CONF 001 004
(1) Task A320-A-46-XX-1088-01001-920A-A (A320-A-46-XX-1088-01ZZZ-920Z-A)
Modify the Equipment and the Wiring in the Cockpit
Job Set-Up Information
Working Area
Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Material necessary to do the job
Part kit 461088A01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9100095418795 1 PLCRDSET (1)
EN3155-019F2018 6 CONTACT
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 401MFD4-3 2 DCDU
Referenced Information
Manuals/Drawings References/Sheets
Task 11-00-00-400-003
Task 20-21-15-912-001
AMM
Task 22-82-12-000-001
Task 22-82-12-400-002
20-33-00
20-52-10
ESPM
20-52-21
20-54-50
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
3 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
FIN 2TX1
1 DCDU-DATALINK 401MFD4-3 Item 2
CONTROL AND DISPLAY
UNIT
FIN 2TX2
1 DCDU-DATALINK 401MFD4-3 Item 2
CONTROL AND DISPLAY
UNIT
5 Bond the placards identified 2TX1 and 2TX2 adjacent to the DCDUs as
shown in view B thru D, supplied in:
6 CONTACT-SOCKET EN3155-019F2018
A B
BEFORE
401VU 400VU
ENGINES
WARNINGS
SYSTEM
PAGES
A
VIEW LOOKING FWD
ICN-A320-A-46XX1088-A-FAPE3-00HYX-A-002-01
AFTER
401VU 400VU
ENGINES
WARNINGS
SYSTEM
PAGES
C
2 2
B
VIEW LOOKING FWD 2TX2
2TX1
C D
401VU
VIEW LOOKING AFT 400VU
VIEW LOOKING AFT
ICN-A320-A-46XX1088-A-FAPE3-00HYY-A-002-01
A B
(3)
INOP
ATC
MSG
01
A
131VU
VIEW LOOKING FWD
01
(3)
INOP
ATC
MSG
B
130VU
VIEW LOOKING FWD
NOTE:
01 INSTALLATION OF THE ATC MSG P/B SWITCH IS RELATED TO
THE AIRCRAFT CONFIGURATION ICN-A320-A-46XX1088-A-FAPE3-023PS-A-002-01
BEFORE
A 2
F.R. -
8 R D
F.R.
7348 C
2
9 B L
-
F.R.
K
3CA1 MCDU-1
11VU 1103VT
210 120
F.R.
A
8 R
7349
9 B
3CA3 MCDU-3
101VU
211
A
2M
8 R 19
7350
F.R.
9 B 20
0569 21
3CA2 MCDU-2
11VU A 63VC
210 127
NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2286
OLD HOOK-UP EXISTING WIRE F.R. FOR REFERENCE UNLESS OTHERWISE SPECIFIED ALL WIRES ARE TK24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE
ICN-A320-A-46XX1088-A-FAPE3-00HZE-A-002-01
AFTER
A 2
F.R. -
17 R D
F.R.
7348 C
2
18 B L
-
F.R.
K
3CA1 MCDU-1
11VU 1103VT
210 120
F.R.
A
17 R
7349
18 B
3CA3 MCDU-3
101VU
211
A
2M
17 R 19
7350
F.R.
18 B 20
0569 21
3CA2 MCDU-2
11VU A 63VC
210 127
NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2286
NEW HOOK-UP EXISTING WIRE F.R. FOR REFERENCE UNLESS OTHERWISE SPECIFIED ALL WIRES ARE TK24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE
ICN-A320-A-46XX1088-A-FAPE3-00HZF-A-002-01
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
19
20
21
23
24
25
Man-hours 2.00 h
Minimum Number of person 1
Elapsed Time 2.00 h
Material necessary to do the job
Part kit 461088A01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
D9100095418795 1 PLCRDSET (1)
EN3155-019F2018 6 CONTACT
NOTE(S)
(1): This item has a Shelf Life of less than or equal to 24 months and must be ordered
when you intend to accomplish the Service Bulletin.
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
2 401MFD4-3 2 DCDU
Referenced Information
Manuals/Drawings References/Sheets
Task 11-00-00-400-003
Task 20-21-15-912-001
AMM
Task 22-82-12-000-001
Task 22-82-12-400-002
20-33-00
20-52-10
ESPM
20-52-21
20-54-50
SRM 51-42-00
Procedure
(a) Standard Practices
1 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
3 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
FIN 2TX1
1 DCDU-DATALINK 401MFD4-3 Item 2
CONTROL AND DISPLAY
UNIT
FIN 2TX2
1 DCDU-DATALINK 401MFD4-3 Item 2
CONTROL AND DISPLAY
UNIT
5 Bond the placards identified 2TX1 and 2TX2 adjacent to the DCDUs as
shown in view B thru D, supplied in:
6 CONTACT-SOCKET EN3155-019F2018
A B
BEFORE
401VU 400VU
ENGINES
WARNINGS
SYSTEM
PAGES
A
VIEW LOOKING FWD
ICN-A320-A-46XX1088-A-FAPE3-00HYX-A-002-01
AFTER
401VU 400VU
ENGINES
WARNINGS
SYSTEM
PAGES
C
2 2
B
VIEW LOOKING FWD 2TX2
2TX1
C D
401VU
VIEW LOOKING AFT 400VU
VIEW LOOKING AFT
ICN-A320-A-46XX1088-A-FAPE3-00HYY-A-002-01
A B
(3)
INOP
ATC
MSG
01
A
131VU
VIEW LOOKING FWD
01
(3)
INOP
ATC
MSG
B
130VU
VIEW LOOKING FWD
NOTE:
01 INSTALLATION OF THE ATC MSG P/B SWITCH IS RELATED TO
THE AIRCRAFT CONFIGURATION ICN-A320-A-46XX1088-A-FAPE3-023PS-A-002-01
BEFORE AFTER
2 2
A A
- -
8 R D 17 R D
7348 2 F.R. 7348 2 F.R.
9 B L 18 B L
- -
F.R. F.R.
1103VT 1103VT
3CA1 MCDU-1 120 3CA1 MCDU-1 120
210 11VU 210 11VU
2M 2M
A A
8 R 19 17 R 19
7350 7350
9 B 20 18 B 20
F.R. F.R.
NEW HOOK-UP OLD HOOK-UP EXISTING WIRE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 2286
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE TK24 GAUGE
F.R. FOR REFERENCE UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
SHIELDING CONTINUITY WIRES ARE CF24 GAUGE
ICN-A320-A-46XX1088-A-FAPE3-00HZG-A-002-01
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
13
14
15
18
19
20
21
22
23
24
25
CONF 001-004
(2) Task A320-A-46-XX-1088-01001-520A-A (A320-A-46-XX-1088-01ZZZ-520Z-A)
Remove the Safety Clips from Rear Circuit Breaker Panel 121VU
Job Set-Up Information
Working Area
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
AMM Task 20-16-00-912-001
Procedure
(a) Standard Practices
1 For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-
912-001.
(b) Remove the safety clips from the rear circuit breaker panel (Electrical Panel
121VU), refer to Ref. Fig. Removal of the Safety Clips from Rear Circuit Breaker
Panel 121VU.
1 Remove from position 17L as shown in view A thru C:
CONF 001-004
A
Z210
FR12
FR1
L
A
120VU
DC
DU
1
DC
DU
2
1
2 C 6TX1
C D 6TX2
16 D
17
18
19
20
21 (4)
B
121VU
C D
TYPICAL VIEW
ICN-A320-A-46XX1088-A-FAPE3-00HYZ-A-003-01
CONF 005
(2) Task A320-A-46-XX-1088-01002-520A-A (A320-A-46-XX-1088-01ZZZ-520Z-A)
Remove the Safety Clips from Rear Circuit Breaker Panel 121VU
Job Set-Up Information
Working Area
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
AMM Task 20-16-00-912-001
Procedure
(a) Standard Practices
1 For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-
912-001.
(b) Remove the safety clips from the rear circuit breaker panel (Electrical Panel
121VU), refer to Ref. Fig. Removal of the Safety Clips from Rear Circuit Breaker
Panel 121VU.
1 Remove from position 44K as shown in views A thru C:
CONF 005
A
Z210
FR12
FR1
K
A
120VU
DC
DU
1
DC
DU
2
1
2 C 6TX1
C D 6TX2
43 D
44
45
46
47
48 (4)
B
121VU
C D
TYPICAL VIEW
ICN-A320-A-46XX1088-A-FAPE3-026BY-A-001-01
CONF ALL
(3) Task A320-A-46-XX-1088-03001-920A-A (A320-A-46-XX-1088-03ZZZ-920Z-A)
Modify the Wiring in the Avionics Compartment
Job Set-Up Information
Working Area
Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Material necessary to do the job
Part kit 461088A01R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
E0170FA2200 4 CONTACT
EN3155-016M2222 10 CONTACT
Referenced Information
Manuals/Drawings References/Sheets
Task 31-53-34-000-001
Task 31-53-34-400-001
AMM
Task 46-21-34-000-001
Task 46-21-34-400-001
20-33-00
ESPM 20-52-21
20-54-50
Procedure
(a) Standard Practices
1 For the general installation of electrical wire harnesses, refer to Ref. ESPM
20-33-00.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
3 For the protection of the connectors, contacts and terminals, refer to Ref.
ESPM 20-54-50.
(b) Remove and retain ATSU-1 (FIN 1TX1), refer to Ref. AMM Task 46-21-34-000-001.
(c) Remove and retain the FWCs (FIN 1WW1 and FIN 1WW2), refer to Ref. AMM Task
31-53-34-000-001.
(d) Modify the wiring.
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WC and Ref. Fig. HC.
If necessary, use:
4 CONTACT-SOCKET E0170FA2200
(e) Modify the pin programming of the DCDUs (FIN 3CA1 and FIN 3CA2).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WB and Ref. Fig. HB.
If necessary, use:
4 CONTACT EN3155-016M2222
(f) Modify the pin programming of ATSU-1 (FIN 1TX1).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WD and Ref. Fig. HD.
If necessary, use:
1 CONTACT EN3155-016M2222
(g) Modify the wiring parity of ATSU-1 (FIN 1TX1).
Refer to Ref. ESPM 20-33-00
1 If, when you did ACCOMPLISHMENT INSTRUCTIONS paragraph Ref. Task
A320-A-46-XX-1088-02ZZZ-311Z-A, you recorded that the aircraft wiring
agrees with line 1 of Ref. Fig. HE:
a Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WE and Ref. Fig. HE.
If necessary, use:
1 CONTACT EN3155-016M2222
2 If, when you did ACCOMPLISHMENT INSTRUCTIONS paragraph Ref. Task
A320-A-46-XX-1088-02ZZZ-311Z-A, you recorded that the aircraft wiring
agrees with line 1 of Ref. Fig. HF:
a Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WF and Ref. Fig. HF.
If necessary, use:
1 CONTACT EN3155-016M2222
(h) Modify the pin programming of the FWCs (FIN 1WW1 and FIN 1WW2).
Refer to Ref. ESPM 20-33-00
1 Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WG and Ref. Fig. HG.
If necessary, use:
2 CONTACT EN3155-016M2222
(i) Modify the wiring parity of FWC-1 (FIN 1WW1).
Refer to Ref. ESPM 20-33-00
1 CONTACT EN3155-016M2222
2 If, when you did ACCOMPLISHMENT INSTRUCTIONS paragraph Ref. Task
A320-A-46-XX-1088-02ZZZ-311Z-A, you recorded that the aircraft wiring
agrees with line 1 of Ref. Fig. HI:
a Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WI and Ref. Fig. HI.
If necessary, use:
1 CONTACT EN3155-016M2222
(j) Modify the wiring parity of FWC-2 (FIN 1WW2).
Refer to Ref. ESPM 20-33-00
1 If, when you did ACCOMPLISHMENT INSTRUCTIONS paragraph Ref. Task
A320-A-46-XX-1088-02ZZZ-311Z-A, you recorded that the aircraft wiring
agrees with line 1 of Ref. Fig. HJ:
a Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WJ and Ref. Fig. HJ.
If necessary, use:
1 CONTACT EN3155-016M2222
2 If, when you did ACCOMPLISHMENT INSTRUCTIONS paragraph Ref. Task
A320-A-46-XX-1088-02ZZZ-311Z-A, you recorded that the aircraft wiring
agrees with line 1 of Ref. Fig. HK:
a Modify the connection of the wire(s) as shown on this (these) wiring
diagram(s) and the related hook-up chart(s):
- Ref. Fig. WK and Ref. Fig. HK.
If necessary, use:
1 CONTACT EN3155-016M2222
(k) Do a continuity test of the new and/or modified electrical wires, refer to Ref.
ESPM 20-52-21.
(l) Install retained ATSU-1 (FIN 1TX1), refer to Ref. AMM Task 46-21-34-400-001.
(m) Install the retained FWCs (FIN 1WW1 and FIN 1WW2), refer to Ref. AMM Task 31-
53-34-400-001.
CONF ALL
BEFORE AFTER
AB 25 AE 25
1C 0169 R 1C 0169 R
- -
32 AB 32
F.R. F.R.
1J 0170 G 1J 0170 G
- -
1WW2 FWC-2 2M 1862VT 1WW2 FWC-2 2M 1862VT
86VU 86VU
128 128
AE 73
AB 73 1C 0173 C
1C 0173 C -
- AB 73 F.R.
73 F.R. 1J 0174 S
1J 0174 S -
-
1WW1 FWC-1 1853VT
1WW1 FWC-1 1853VT
85VU
85VU 127
127
NEW HOOK-UP OLD HOOK-UP STOWED WIRE F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 4621
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
ICN-A320-A-46XX1088-A-FAPE3-00HZK-A-003-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
2 85VU 1WW1-AE 1C E0170FA2200 4621-0173 1M CF24 85VU 1853VT 73C M1N (1)
4 85VU 1WW1-AB 1J E0170FA2200 4621-0174 1M CF24 85VU 1853VT 73S M1N (1)
6 86VU 1WW2-AE 1C E0170FA2200 4621-0169 2M CF24 86VU 1862VT 25R M1N (1)
8 86VU 1WW2-AB 1J E0170FA2200 4621-0170 2M CF24 86VU 1862VT 32G M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
27
E 23
F.R. 54 0133 F F.R. 54 0133 F
- F.R.
1813VT
A 41VC 127 A 41VC 1813VT
127 81VU 127 127
81VU
2M
2 2M
C
68 0122 D 68 0122
2 5
E F.R. D
F.R. 69 0123 F 69 0123 F
L
2 72 0126 - F.R.
K
72 0126 L A 110VC 1822VT
128 128
A 110VC 1822VT 82VU
128 128
82VU
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 4621
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1M
ICN-A320-A-46XX1088-A-FAPE3-00HZI-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
8 81VU 1813VT 23F EN3155-016M2222 4621-0133 1M CF24 127 41VC 54 M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AB 17 AB 18
15B 0033 C 15B 0033 C
- F.R. D - F.R. - F.R.
1813VT 1813VT
1TX1 ATSU-1 127 1TX1 ATSU-1 127
127 81VU 81VU 127 81VU 81VU
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 4621
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 2M
ICN-A320-A-46XX1088-A-FAPE3-00HZM-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
2 81VU 1813VT 18C EN3155-016M2222 4621-0033 2M CF24 81VU 1TX1-AB 15B M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 81VU 1813VT 16D 4621-0043 2M CF24 81VU 1TX1-AB 14K M1O (2)
2 81VU 1813VT 18D EN3155-016M2222 4621-0043 2M CF24 81VU 1TX1-AB 14K M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AB 16 AB 18
14K 0043 D 14K 0043 D
- F.R. C - F.R. - F.R.
1813VT 1813VT
1TX1 ATSU-1 127 1TX1 ATSU-1 127
127 81VU 81VU 127 81VU 81VU
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 4621
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 2M
ICN-A320-A-46XX1088-A-FAPE3-00HZN-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 81VU 1813VT 18D 4621-0043 2M CF24 81VU 1TX1-AB 14K M1O (2)
2 81VU 1813VT 16D EN3155-016M2222 4621-0043 2M CF24 81VU 1TX1-AB 14K M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AB 18 AB 16
14K 0043 D 14K 0043 D
- F.R. - F.R. - F.R. C
1813VT 1813VT
1TX1 ATSU-1 127 1TX1 ATSU-1 127
127 81VU 81VU 127 81VU 81VU
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 4621
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 2M
ICN-A320-A-46XX1088-A-FAPE3-00HZO-A-002-01
CONF ALL
BEFORE AFTER
AA AA
63 62
10C 0870 A 10C 0870 A
AA AA
2S 2S
11 12
10C 0861 A 10C 0861 A
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3152
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1S
ICN-A320-A-46XX1088-A-FAPE3-00HZP-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
2 85VU 1851VT 62A EN3155-016M2222 3152-0870 1S CF24 85VU 1WW1-AA 10C M1N (1)
4 86VU 1860VT 12A EN3155-016M2222 3152-0861 2S CF24 86VU 1WW2-AA 10C M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 85VU 1851VT 61A 3152-0785 1S CF24 85VU 1WW1-AD 10A M1O (2)
2 85VU 1851VT 59A EN3155-016M2222 3152-0785 1S CF24 85VU 1WW1-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AD AD
61 59
10A 0785 A 10A 0785 A
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3152
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1S
ICN-A320-A-46XX1088-A-FAPE3-00HZR-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 85VU 1851VT 59A 3152-0785 1S CF24 85VU 1WW1-AD 10A M1O (2)
2 85VU 1851VT 61A EN3155-016M2222 3152-0785 1S CF24 85VU 1WW1-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AD AD
59 61
10A 0785 A 10A 0785 A
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3152
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 1S
ICN-A320-A-46XX1088-A-FAPE3-00HZS-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 86VU 1860VT 10A 3152-0772 2S CF24 86VU 1WW2-AD 10A M1O (2)
2 86VU 1860VT 8A EN3155-016M2222 3152-0772 2S CF24 86VU 1WW2-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AD AD
10 8
10A 0772 A 10A 0772 A
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3152
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 2S
ICN-A320-A-46XX1088-A-FAPE3-00HZT-A-002-01
CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
2 86VU 1860VT 10A EN3155-016M2222 3152-0772 2S CF24 86VU 1WW2-AD 10A M1N (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CONF ALL
BEFORE AFTER
AD AD
8 10
10A 0772 A 10A 0772 A
NEW HOOK-UP OLD HOOK-UP F.R. FOR REFERENCE NOTE : UNLESS OTHERWISE SPECIFIED PREFIX ALL WIRE IDENTIFICATION WITH ATA 3152
UNLESS OTHERWISE SPECIFIED ALL WIRES ARE CF24 GAUGE
UNLESS OTHERWISE SPECIFIED ALL ROUTES ARE 2S
ICN-A320-A-46XX1088-A-FAPE3-00HZU-A-002-01
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
Task 20-16-00-912-001
Task 22-82-12-400-002
AMM 24-50-00
Task 31-53-34-400-001
Task 46-21-34-400-001
Procedure
(a) Remove the safety clip(s) and/or tag(s) and close/unlock this (these) circuit
breaker(s):
NOTE: For the circuit breaker location, refer to Ref. AMM 24-50-00.
NOTE: For the circuit breaker safety practices, refer to Ref. AMM Task 20-16-00-
912-001.
(b) Remove the safety clip(s) and/or tag(s) and close/unlock the circuit breaker(s) as
specified after the installation of the FWCs (FIN 1WW1 and FIN 1WW2), refer to
Ref. AMM Task 31-53-34-400-001.
(c) Remove the safety clip(s) and/or tag(s) and close/unlock the circuit breaker(s) as
specified after the installation of ATSU-1 (FIN 1TX1), refer to Ref. AMM Task 46-
21-34-400-001.
(d) Remove the safety clip(s) and/or tag(s) and close/unlock the circuit breaker(s) as
specified after the installation of the MCDUs (FIN 3CA1, FIN 3CA2 and, if installed
FIN 3CA3), refer to Ref. AMM Task 22-82-12-400-002.
E. TEST
(1) Task A320-A-46-XX-1088-01001-390A-A (A320-A-46-XX-1088-01ZZZ-390Z-A)
Test
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h
Referenced Information
Manuals/Drawings References/Sheets
Task 22-82-12-400-002
Task 31-50-00-740-002
AMM
Task 31-53-34-400-001
Task 46-21-34-400-001
Procedure
(a) Do the test procedure as specified after the installation of the FWCs (FIN 1WW1
and FIN 1WW2), refer to Ref. AMM Task 31-53-34-400-001.
(b) Do the test procedure as specified after the installation of ATSU-1 (FIN 1TX1),
refer to Ref. AMM Task 46-21-34-400-001.
(c) Do the test procedure as specified after the installation of the MCDUs (FIN 3CA1,
FIN 3CA2 and, if installed FIN 3CA3), refer to Ref. AMM Task 22-82-12-400-002.
(d) Do the Built-In Test Equipment (BITE) test of the ATIMS, refer to Ref. Appendix
ADVANCE COPY OF AMM TASK(S).
(e) Read and decode the hardware pin programming of the System Data Acquisition
Concentrator (SDAC) and the FWC, refer to Ref. AMM Task 31-50-00-740-002.
1 Print the results for FWC.
NOTE: You must make sure that the FWC-1 and FWC-2 parity status is OK.
NOTE: From the right side, you must make sure that the 1st digit of the
4th line is set to 0, related to the activation of the 'ATC FUNCTION
IN ATSU'.
F. CLOSE-UP
(1) Task A320-A-46-XX-1088-01001-740A-A (A320-A-46-XX-1088-01ZZZ-740Z-A)
Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00 h
Referenced Information
Manuals/Drawings References/Sheets
Task 22-82-12-400-002
Task 25-54-11-400-001
AMM
Task 31-53-34-400-001
Task 46-21-34-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Do the close-up procedure as specified in the installation of the FWCs (FIN 1WW1
and FIN 1WW2), refer to Ref. AMM Task 31-53-34-400-001.
(c) Do the close-up procedure as specified in the installation of ATSU-1 (FIN 1TX1),
refer to Ref. AMM Task 46-21-34-400-001.
(d) Do the close-up procedure as specified in the installation of the MCDUs (FIN
3CA1, FIN 3CA2 and if installed FIN 3CA3), refer to Ref. AMM Task 22-82-12-400-
002.
(e) Install the partition panels (Panel 131CW, Panel 131DW and Panel 132EW) in the
FWD cargo compartment, at Frame 24A, refer to Ref. AMM Task 25-54-11-400-
001.
(f) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-46-XX-1088-01001-90AA-A (A320-A-46-XX-1088-01ZZZ-90AZ-A)
Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.
MOD CONF 001 CONF 002 CONF 003 CONF 004 CONF 005
31442P6830 X X X X X
36344P9610 X X
38198P9842 X X X X X
153972P13136 X X X X X
155918P14116 X X X X X
151451P6062 X X X X X
151451P7346 X X X X X
151451P7350 X X X X X
151451P8893 X X X X X
NOTE:
"X" IS USED FOR THE RETROFITTED MODIFICATIONS AFTER ACCOMPLISHMENT
OF THIS SERVICE BULLETIN. ICN-A320-A-46XX1088-A-FAPE3-00HYW-A-003-01
NOTE:
"X" IS USED FOR MODIFICATIONS EMBODIED BEFORE ACCOMPLISHMENT OF THIS SERVICE BULLETIN. ICN-A320-A-46XX1088-A-FAPE3-0240X-A-002-01
(b) Procedure
1 BITE Test of the ATIMS
NOTE: During the test, obey the instructions on the MCDU.
ACTION RESULT
1.On the MCDU 1: On the MCDU 1:
- push the line key adjacent to - the ATIMS page comes
the ATIMS indication. into view.
ICN-A320-A-46XX1088-A-FAPE3-023PV-A-002-01
ACTION RESULT
On the DCDU 2:
- the INVALID DATA message
comes into view, then goes
out of view.
On the DCDU 1 and DCDU 2:
- the first test screen
(colors) comes into view.
On the upper ECAM DU:
- the COM ACARS FAULT or
DATALINK ATSU FAULT warning
message goes out of view.
On the MCDU 1:
- the ATIMS SYSTEM TEST page
related to the first test
screen (colors) of the
DCDUs comes into view.
On the MCDU 1:
- the TEST IN PROGRESS 150s
message comes into view in
the ATIMS SYSTEM TEST page.
NOTE: The message can also be
TEST IN PROGRESS 180s.
ICN-A320-A-46XX1088-A-FAPE3-023PW-A-002-01
ACTION RESULT
On the MCDU 1:
- at the end of the test, the
TEST OK indication comes
into view.
6.On the MCDU 1: The test procedure stops.
- push the line key adjacent to
the RETURN indication.
(c) Close-up
1 Put the aircraft back to its initial configuration.
a On the MCDU, push the line key adjacent to the RETURN indication
until the CFDS menu page comes into view.
b On the MCDU, fully decrease the brightness of the MCDU screen
(display off).
c Do the EIS stop procedure, (Refer to AMM TASK 31-60-00-860-0020).
ICN-A320-A-46XX1088-A-FAPE3-023PX-A-002-01
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.