Professional Documents
Culture Documents
4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
Mechanical specifications
mounting hardware
Weight kg 15 / 17.2 (clamps incl.)
lb 33.1 / 37.9 (clamps incl.)
Packing size mm 1600 x 337 x 112
inches 63.0 x 13.3 x 4.4
Scope of supply Panel and 2 units of clamps
for 42 – 115 mm |
1.7– 4.5 inches diameter
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Accessories
General Information
1)
Remarks Weight approx. Units per 3) 9 | 0.4
Type No. Description
mm | inches kg | lb antenna
1319 | 51.9
1384 | 54.5
1529 | 60.2
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.
Correlation Table
Frequency range Array Connector
Adjustment
1710 – 2200 MHz B1 1–2 mechanism
with integrated
1710 – 2200 MHz B2 3–4 scale
All dimensions in
mm | inches
B1 B2
Left Right
Layout of interface:
255 | 10.0
49 | 1.9
41 | 1.6
71 | 2.8
102 | 4.0
Subject to alteration.
315 | 12.4
936.4881/a
Bottom view
Dimensions in mm | inches
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Adjustment Mechanism
1
2
2
➀ Adjustment wheel with twist-lock ➀ Thread for fixing the protective To set the downtilt angle exactly,
function. cap or the RCU (Remote Control you must look horizontally at the
➁ Downtilt spindle with integrated Unit). scale. The lower edge of the gear-
scale. ➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
max.° – 0°
Remove the protective cap. Set downtilt angle by rotating the Screw on the protective cap again.
adjustment wheel.
For a description of RCU installation please refer to the respective data sheet.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions for Feederline Installation
on Panels with four Connectors
arranged on two Levels
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
4 3
2 1
There are four interfaces for feeding the antenna The connectors are mounted at two levels in order to facilitate feederline
located at the bottom. installation.
Start with the rearside located inter- After feederline installation the optional For a full description of RCU installation
face no. 1. remote control units (RCU) can be please refer to the respective data sheet.
mounted if required.
Place the connector carefully and fix the
nut using a torque-wrench (according to
the manufacturers guidelines).
Subject to alteration.
Please note: Additional weather sealing of correctly installed feederline connector interfaces is not required,
nor is it recommended by the connector manufacturers.