Professional Documents
Culture Documents
Data Sheet of Process Equipment Design: PROJECT Sokoria Project
Data Sheet of Process Equipment Design: PROJECT Sokoria Project
PROJECT:Sokoria Project
EQUIPMENT:Evaporative Condenser
DWG NO。YLN-2400
设 计 日期
Mingheng zhou 2021.3.9
Designed by Date
校 核 日期
Lei Yu 2021.3.9
Checked by Date
审 核 日期
Xiang Li 2021.3.9
Verified by Date
批 准 日期
Xu Zhu 2021.3.9
Approved by Date
应力分析报告 Stress Analysis Report sheet 1 of 21
目 录
CONTENTS
表 2 主要构件计算参数
Table2 The parameters of main components in stress calculation
构件名称 材料 设计尺寸(mm) 计算尺寸(mm)
Component Material Design dimension (mm) Calculate dimension (mm)
接管 SA312
φ219.08×8.0 φ219.08×7.2
Nozzle TP316L
管箱 SA312
φ219.08×6.3 φ219.08×5.67
Channel TP316L
端板 SA240
δ=6 δ=5.7
End plate 316L
换热管 SA312 31.8x21.6x1.1(椭圆) 31.8x21.6x0.99(椭圆)
Heat exchanger tubes TP316L (Elliptical) (Elliptical)
材料在计算温度下的力学性能参数见表 3。
The mechanical properties of the material at the calculation temperatures are shown in Table 3.
表 3 材料在计算工况下的力学性能参数(80℃)
Table 3 Mechanical properties of the material at the calculation temperature (80℃)
弹性模量 E (MPa)
材料 泊松比 v 许用应力 Sm (MPa)
Elastic moduli Allowable stress Sm (MPa)
Material Poisson’s ratio
(MPa)
SA312 TP316L 1.906×105 0.31 Sm=115
SA240 316L 1.906×105 0.31 Sm=115
有限元模型见下图。有限元模型中使用三维结构单元 SOLID185。
The FEA model is shown in the figure 2, 3D model element SOLID185 is used in the FEA model.
结构承受以下载荷:
The following loads are applied to the structure:
作用于内表面的压力;
The internal pressure applied on the inside surface.
接管端面的轴向平衡载荷。
The axial balanced load on the end surface of nozzle.
力学模型如图 3 所示。
The stress model is shown in Figure 3.
3.4. 结论(Conclusion)
从以上的计算结果可以看出,本结构的应力是合格的。
According to the above calculation result,the stress evaluation of this structure is qualified.
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
-29.48 -6.433 -79.69 -15.90 1.193 -1.577
S1 S2 S3 SINT SEQV
1.723 -37.58 -79.74 81.47 70.57
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
21.42 65.21 9.516 -5.948 -2.163 0.5609
S1 S2 S3 SINT SEQV
66.09 20.63 9.423 56.66 51.97
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
2.792 -16.44 -5.506 -3.487 6.819 -25.48
S1 S2 S3 SINT SEQV
应力分析报告 Stress Analysis Report sheet 11 of 21
有限元模型见下图。有限元模型中使用三维结构单元 SOLID185。
The FEA model is shown in the figure 2, 3D model element SOLID185 is used in the FEA model.
应力分析报告 Stress Analysis Report sheet 13 of 21
结构承受以下载荷:
The following loads are applied to the structure:
作用于内表面的压力;
The internal pressure applied on the inside surface.
接管端面的轴向平衡载荷。
The axial balanced load on the end surface of nozzle.
力学模型如图 8 所示。
The stress model is shown in Figure 8.
应力分析报告 Stress Analysis Report sheet 14 of 21
5.4. 结论(Conclusion)
从以上的计算结果可以看出,本结构的应力是合格的。
According to the above calculation result,the stress evaluation of this structure is qualified.
应力分析报告 Stress Analysis Report sheet 18 of 21
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
5.689 -6.993 -0.1467 4.495 23.53 2.229
S1 S2 S3 SINT SEQV
21.56 4.449 -27.46 49.02 43.09
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
-14.63 -66.00 -110.0 -19.03 21.28 -4.793
S1 S2 S3 SINT SEQV
-7.054 -64.88 -118.6 111.6 96.66
** MEMBRANE **
SX SY SZ SXY SYZ SXZ
1.231 -9.901 21.36 -0.9539E-02 18.39 -0.1628
S1 S2 S3 SINT SEQV
29.87 1.230 -18.40 48.27 42.04