Professional Documents
Culture Documents
ML13055 Wideband FSK Receiver: Legacy Device: Motorola MC13055
ML13055 Wideband FSK Receiver: Legacy Device: Motorola MC13055
ML13055 Wideband FSK Receiver: Legacy Device: Motorola MC13055
• Easy Application, Few Peripheral Components Note: Lansdale lead free (Pb) product, as it
becomes available, will be identified by a part
• Operating Temperature Range TA = –40° to +85°C number prefix change from ML to MLE.
PIN ASSIGNMENT
VCC
0.01
16 Data
1
15 Output
+
2 – 14
3 Comparator Gnd 1 16 Data Out
0.01 0.8V – 13 100pF Carrier Comparator VCC 2 + 15
40MHz
4 + Detect Comparator
IF
12 IF Ground 3 – 14
Input
22pF 5 Squelch
(50Ω)
5.0k Adjust IF VCC 4 13 Carrier Detect
27pF 6 Limiter (meter)
Limiter Input 5 12 Meter Drive
L1 11 68pF
0.1
7 10 6 11
3.9k Limiter Bias
7 10
Detector
0.01 9 Out
8 VCC
3.9k Quad Bias 8 9 Quad Input
1.0k
39pF
L2
Figure 1. Block Diagram and Application Circuit
MAXIMUM RATINGS
Rating Symbol Value Unit
Power Supply Voltage VCC(max) 15 Vdc
Operating Supply Voltage Range V2, V4 3.0 to 12 Vdc
Junction Temperature TJ 150 °C
Operating Ambient Temperature Range TA -40 to +85 °C
Storage Temperature Range Tstg -65 to +150 °C
Power Dissipation, Package Rating PD 1.25 W
ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, fo = 40 MHz, fmod = 1.0 MHz, ∆f = ±1.0 MHz, TA = 25°C, test circuit of Figure 2.)
Characteristic Conditions Min Typ Max Unit
Total Drain Current I2 + I4 20 25 mA
Data Comparator Pull–Down Current I16 10 mA
Meter Drive Slope versus Input I12 4.5 7.0 9.0 µA/dB
Carrier Detect Pull–Down Current I13 1.3 mA
Carrier Detect Pull–Up Current I13 500 µA
Carrier Detect Threshold Voltage V12 690 800 1010 mV
DC Output Current I10, I11 430 µA
Recovered Signal V10 - V1 1 350 mVrms
Sensitivity for 20 dB S+N/N, BW = 5.0 MHz VIN 20 µVrms
S+N/N at Vin = 50 µV V10 - V1 1 30 dB
Input Impedance @ 40 MHz Rin Pin 5, Ground 4.2 kΩ
Cin 4.5 pF
1 16
0.01
2 15
VCC
3
100pF
14
0.01
4
22pF 13 Carrier
5 Detect Output
Input
12
27pF Meter Drive
L1
6
11
0.1 Detector
7 10 Output
0.01 0.01
8 9 3.9k 3.9k
1.0k
Coils - Shielded
39pF Coilcraft UNI-10/142
L1 Gray 8 1/2 Turns, nominal 300 nH
L2 Black 10 1/2 Turns, nominal 380 nH
L2
Figure 3. Overall Gain, Noise, AM Rejection Figure 4. Meter Current versus Signal
0
Output fmod = 1.0 MHz 600 VCC = 5.0 V, 7.0 V
500 3.0 V
-20
400 12 V
-30 Noise
300
-40
AMR 1.0 kHz 200
-50 30%
100
-60
0
-100 -80 -60 -40 -20 0 -100 -80 -60 -40 -20 0
SIGNAL INPUT (dBm) INPUT SIGNAL (dBm)
Figure 5. Untuned Input: Limiting Sensitivity Figure 6. Untuned Input: Meter Current
versus Frequency versus Frequency
0 800
VIN, INPUT LIMITING SENSITIVITY (dBm)
0.1
0.1 5 9
-10 Input
5 9 l12, METER CURRENT (µ Adc) 700 Input 0 dBm Input
51 ML13055 20k
-20 51 ML13055 20k -10
8
600 7 8
-30 7
-20 0.1
0.1
-40 500 -30
-70 -60
200
-80 -70
100
-90 -80
-100 0
0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 60 70 80 90 100
f, INPUT FREQUENCY (MHz) f, INPUT FREQUENCY (MHz)
Figure 7. Limiting Sensitivity and Detuning Figure 8. Detector Current and Power Supply
versus Supply Voltage Current versus Supply Voltage
40 3 1200 60
VIN, INPUT LIMITING SENSITIVITY (dBm)
Quadrature
-40 40.2
40 MHz Coil Tuning
40.1 1000 50
QUAD COIL TUNING (MHz)
4.0
2.0 900
0
-2.0 800
-4.0
-6.0 700
-8.0
-10 600
-12
500
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)
Figure 11. Meter Current versus Temperature Figure 12. Input Limiting versus Temperature
600
500
-20 -60
400 -30
-70
-40
300
-50 -80
200
-60 -90
100
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)
Cp = 4pF
0.5 Rp = 4kΩ
Y = 0.24 + j1.1
0.2 5.0
50M 20M
30M
0.5 2.0
1.0
Legacy Information
2
LANSDALE Semiconductor, Inc.
71 73 76 80 16
74 77 78 79
72 85 94
92
Figure 15. d
89 92
13 86 91
69 90 14
83
67 70 84 87
12 66 68
81 82
1
15
9 8
4
46 35
65
36
www.lansdale.com
25
13 14 15 16 17 18 19 20 21 22 23 24
37 39
5 26
38
B B 31 32 33 34
25
6
26
7 10
27
29 30
60 61 62 63 64 11 48 47
45 28
52 53 51
58 57 56 55 54
59 49
50
Issue B
ML13055
ML13055 LANSDALE Semiconductor, Inc.
GENERAL DESCRIPTION
The ML13055 is an extended frequency range FM IF, A simple squelch arrangement is provided whereby the
quadrature detector, signal strength detector and data meter current flowing through the meter load resistance
shaper. It is intended primarily for FSK data systems. flips a comparator at about 0.8 Vdc above ground. The
The design is very similar to ML3356 except that the signal strength at which this occurs can be adjusted by
oscillator/mixer has been removed, and the frequency changing the meter load resistor. The comparator (+)
capability of the IF has been raised about 2:1. The input and output are available to permit control of hys-
detector output configuration has been changed to a teresis. Good positive action can be obtained for IF
balanced, open-collector type to permit symmetrical input signals of above 20 µVrms. A resistor (R) from
drive of the data shaper (comparator). Meter drive and Pin 13 to Pin 12 will provide VCC/R of feedback cur-
squelch features have been retained. rent. This current can be correlated to an amount of sig-
nal strength hysteresis by using Figure 4.
The limiting IF is a high frequency type, capable of
being operated up to 100 MHz. It is expected to be used The squelch is internally connected to the data shaper.
at 40 MHz in most cases. The quadrature detector is Squelch causes the data shaper to produce a high
internally coupled to the IF, and a 2.0 pF quadrature (VCC) output.
capacitor is internally provided. The 20 dB quieting sen-
sitivity is approximately 20 µ V, tuned input, and the IF The data shaper is a complete “floating” comparator,
can accept signals up to 220 mVrms without distortion with diodes across its inputs. The outputs of the quadra-
or change of detector quiescent DC level. ture detector can be fed directly to either or preferably
both inputs of the comparator to produce a squared out-
The IF is unusual in that each of the last 5 stages of the put swinging from VCC to ground in inverted or nonin-
6 stage limiter contains a signal strength sensitive, cur- verted form.
rent sinking device. These are parallel connected and
buffered to produce a signal strength meter drive which
is fairly linear for IF input signals of 20 µ V to 20
mVrms (see Figure 4).
OUTLINE DIMENSION
P-DIP 16
(ML13055EP)
PLASTIC PACKAGE NOTES:
-A- 1. DIMENSIONING AND TOLERANCING PER ANSI
CASE 648-08 Y14.5M, 1982.
ISSUE R 2. CONTROLLING DIMENSION: INCH.
16 9 3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
B 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
1 8 5. ROUNDED CORNERS OPTIONAL.
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
F C L A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
S C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
SEATING F 0.040 0.70 1.02 1.77
-T- PLANE G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
H K M J 0.008 0.015 0.21 0.38
J K 0.110 0.130 2.80 3.30
G L 0.295 0.305 7.50 7.74
D 16 PL
M 0° 10° 0° 10°
0.25 (0.010) M T A M S 0.020 0.040 0.51 1.01
SO 16
(ML13055-5P)
PLASTIC PACKAGE
-A- CASE 751B-05
(SO-16) NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
ISSUE J Y14.5M, 1982.
16 9 2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
-B- MOLD PROTRUSION.
P 8 PL
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
1 8
0.25 (0.010) M B S PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOW ABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
G
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
F A 9.80 10.00 0.386 0.393
K R X 45° B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
C F 0.40 1.25 0.016 0.049
-T- SEATING G 1.27 BSC 0.050 BSC
PLANE
M J J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
D 16 PL M 0° 7° 0° 7°
P 5.80 6.20 0.229 0.244
0.25 (0.010) M T B S A S R 0.25 0.50 0.010 0.019
Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliabili-
ty, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent rights nor the rights of others. “Typical” parameters which
may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s
technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc.