Professional Documents
Culture Documents
General: Specifications
General: Specifications
Toggles
General Specifications
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold
Insulation Resistance: 200 megohms minimum @ 500V DC
D Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
Mechanical Life: 1,000,000 operations minimum for momentary circuit
200,000 operations minimum for maintained circuit
Electrical Life: 100,000 operations minimum
Nominal Operating Force: Single pole: 1.47N for nonsealed; 1.67N for sealed
Double pole: 2.75N for nonsealed; 2.94N for sealed
Contact Timing: Nonshorting (break-before-make)
Keylocks
Travel: Pretravel .059” (1.5mm); Overtravel .059” (1.5mm); Total Travel .118” (3.0mm)
Environmental Data
Tactiles
Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Tilt
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Sealing: IP65 of IEC60529 standard for panel seal models
Touch
Installation
Mounting Torque: 0.785Nm (6.95 lb•in) maximum
Quick Connect Force: 24.5N maximum downward force on connector
Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section.
Indicators
Add “/U” or “/CUL” before first dash in part number to order UL recognized switch.
All solder lug models recognized at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
Supplement
All solder lug models certified at 3A @ 125/250V AC or 0.4VA @ 28V AC/DC maximum.
D104 www.nkkswitches.com
7/27/17
Short Body Pushbuttons Series YB
Toggles
Distinctive Characteristics
Rockers
Full face or spot illumination with incandescent lamps or multi-element LEDs,
with or without resistors.
Pushbuttons
Choice of super bright LEDs in white, green, and blue as well as bright LEDs
in red, amber, and green.
Programmable Illuminated PB
Combination bezel-barrier is an integral part of the switch and
prevents accidental actuation. D
Unique thermoplastic elastomer seal inside caps plus
rolled sleeve of nitrile butadiene rubber at joining of
housing and inner case, all for added protection to
interior mechanism.
Keylocks
Dust and oil tight as well as splashproof panel seal
models qualify to IP65 of IEC60529 Standards (similar
to NEMA 4 and 13). Panel seal models provided
with exterior o-ring.
Rotaries
Distinctive design of snap-action contacts for shock
resistance, long life, and sensitive actuation.
Slides
High density design to give behind panel depth of less than
one inch.
Tactiles
Terminals are epoxy sealed to lock out flux, dust, solvents, and other
contaminants.
Tilt
Latchdown for indication of circuit status, plus audible, tactile feedback
with smooth, responsive operation.
www.nkkswitches.com D105
Series YB Short Body Pushbuttons
Toggles
TYPICAL SWITCH
YB 1 5 C K W 01
Rockers
Pushbuttons
2 DPDT
With Panel Seal 03 Straight PC
D W
(Bushing Mount only)
M Round
N Rectangular
Slides
IMPORTANT:
Switches are supplied without UL & cULus marking unless specified.
UL & cULus recognized only when ordered with marking on switch.
Tactiles
YB15CKW01-6F-JB
Touch
D106 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
ORDERING EXAMPLE
6 F JB
Rockers
Pushbuttons
Lamps Cap Types & Colors
Programmable Illuminated PB
Incandescent Lamp Solid Cap: Lens/Insert Colors
05 5-volt BB White/White D
12 12-volt CB Red/White
No EB Yellow/White
Nonilluminated
Code
FB Green/White
GB Blue/White
Keylocks
LED for Spot Illuminated Cap Spot Illuminated Cap: Lens/Insert Colors
LED Colors Forward Voltage JA Clear/Black
1C Red 2-volt JB Clear/White
02
(no resistor)
1D Amber JC Clear/Red
Rotaries
05 5-volt
JE Clear/Yellow
1F Green
12 12-volt
JF Clear/Green
1CF Red/Green 24 24-volt
Slides
Bright LED LED Cap: Lens/Insert Colors
LED Colors Resistor JB Clear/White
No Code No Resistor JC Clear/Red
Tactiles
5C Red
05 5-volt JD Clear/Amber
5D Amber
12 12-volt JF Clear/Green
5F Green 24 24-volt
Tilt
Super Bright LED LED Cap: Lens/Insert Colors
6B White JB Clear/White
Touch
6F Green
6G Blue
Indicators
Bicolor LED for Full Face Illuminated LED Cap: Lens/Insert Colors
LED Colors Forward Voltage JB Clear/White
2-volt
02
(no resistor)
Accessories
www.nkkswitches.com D107
Series YB Short Body Pushbuttons
Toggles
Normal Down Normal Down Notes: Switch is marked with NC, NO, COM, L+, L–.
Pole Model Lamp circuit is isolated and requires
external power source.
Pushbuttons
1 (COM)
YB15 ON (ON)
SP 1-3 1-2 SPDT L (+) (-) L
*YB16 ON ON 3 2
1 (COM) 4
YB25 ON (ON)
Programmable Illuminated PB
D
* When in latchdown position for the alternate circuit, cap position is .020” (0.5mm) above the built-in bezel.
PANEL SEAL
Supplied with
Supplied with mounting nut
mounting nut. and o-ring AT089.
S C R K M N
Tactiles
HOUSING
Indicators
K Black
Housing available in black only. The 1-piece body and bezel-barrier have a matte finish.
G
Supplement
D108 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
TERMINALS
Solder Lug/
01 .110” (2.8mm) Quick Connect
Epoxy Seal (7.3)
.288
Rockers
(2.0)
.079 (2.8)
(1.2) .110
.047
Thk = (0.5)
.020
Pushbuttons
(3.7) Typ (3.7) Typ
03 Straight PC (4.4)
3 .146 6 3 .146
Epoxy Seal
.173 2 5 2
(0.6) R (4.85) Typ (4.85) Typ
Programmable Illuminated PB
.024 (2.8)
.110
Single Pole 1 .191 Double Pole 4 1 .191
D
(1.2)
.047 (3.0) (1.6) Dia Typ (3.0) Typ (1.6) Dia Typ
.118 .063 .118 .063
Thk = (0.5) (5.55) (5.55) Typ
.020
CL .219 CL .219
Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation.
For dimension drawing of lamp see the Accessories & Hardware section.
Keylocks
AT611 05 12
Voltage V 5V AC 12V AC
Rotaries
Current I 115mA 60mA
MSCP .150 .150
T-1 Bi-pin Endurance Hours 7,000 average
Slides
Ambient Temperature Range –25°C ~ +50°C
No Code No Lamp
Tactiles
Solid Cap for Incandescent Lamp & Nonilluminated
Tilt
Colors Available: Round
Translucent Colored Lens
(12.2)
.480
(4.0)
BB White/White
.157
Touch
CB AT3001 AT3003
Red/White Square Rectangular Translucent White Insert
Indicators
EB Yellow/White
(15.0) Sq
.591 (21.0)
(15.0) .827
.591
FB
(12.2)
.480
Green/White (4.0)
(12.2)
Accessories
.480
.157
(4.0) Translucent White Seal/Filter
GB Blue/White
.157
Materials:
Supplement
Lens & Insert: Polycarbonate Seal/Filter: Thermoplastic Elastomer Incandescent Lamp AT611
www.nkkswitches.com D109
Series YB Short Body Pushbuttons
Toggles
Square (15.0) Sq
Round Rectangular (15.0) (21.0)
.591 .591 .827
(15.0) Dia
.591
(2.0) (2.0) (2.0)
.079 (12.2) .079 .079 (12.2)
(12.2)
Pushbuttons
D
Colors Available:
02 02 05 12 24
1C 1D 1F 1CF Without Resistor Without Resistor With With With
Red or Green or Resistor Resistor Resistor Unit
Red Amber Green Red/Green Amber Red/Green All Colors All Colors All Colors
The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires
external power source. Single color LEDs are colored in OFF state. Bicolor LED is translucent white in OFF state.
Tilt
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Lens/Insert
Touch
Colored Insert
for a
JB Clear/White Square Spot Illuminated Cap
with Green 2-volt LED
JC Seal
Accessories
D110 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
BRIGHT LED & LED CAPS
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
Rockers
The resistor value can be calculated by using the formula in the Supplement section.
Pushbuttons
Bright Colors
AT628 Available:
5C Red
5D Amber
5F Green
No Code No Resistor Unit
LED Colors Red Amber Green
Programmable Illuminated PB
Maximum Forward Current IFM 40 40 40 mA
Typical Forward Current IF 26 26 26 mA
D
Forward Voltage VF 1.9 2.0 2.0 V
(+) (-) Maximum Reverse Voltage VRM 4 4 4 V
Current Reduction Rate Above 25°C ∆IF 0.50 mA/°C
T-1 Bi-pin Ambient Temperature Range –25 ~ +50 °C
Keylocks
Electrical Specifications for Bright LED with Resistor
Bright Colors
AT634 Available:
5C Red
5D Amber
5F Green
05 12 24 Unit
Rotaries
Maximum Forward Current IFM — — — mA
Typical Forward Current IF 25 20 10 mA
Forward Voltage VF 5 12 24 V
Maximum Reverse Voltage VRM 4 8 16 V
Slides
Current Reduction Rate Above 25°C ∆IF –––– –––– –––– mA/°C
T-11⁄4 Bi-pin
Ambient Temperature Range –25 ~ +50 °C
Tactiles
AT634 AT634 AT634
5-volt, 12-volt, 24-volt, (+)
(+) (-) (+) (-)
2-element 4-element 4-element (-)
with Resistor with Resistor with Resistor
Tilt
Lens/Insert AT3004 (15.0) Sq AT3005
.591 (15.0) Dia
Colors Available: Square Round .591 Transparent Clear Lens
Touch
(12.2)
.480 (12.2)
JB Clear/White
(4.0)
.157 (4.0)
.480
.157
Translucent Colored Insert
Indicators
JC Clear/Red
(21.0)
(15.0) .827
JD Clear/Amber
.591
Translucent White Seal/Diffuser
AT3006
Accessories
(12.2)
Rectangular .480
JF Clear/Green
(4.0)
.157
Supplement
www.nkkswitches.com D111
Series YB Short Body Pushbuttons
Toggles
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Pushbuttons
Super Bright
AT625G Blue ATTENTION 6B 6F 6G
Programmable Illuminated PB
Current Reduction Rate Above 25°C ∆IF 0.40 0.40 0.40 mA/°C
T-1 Bi-pin Ambient Temperature Range –25 ~ +50 °C
(15.0) Sq (21.0)
.591 (15.0) Dia (15.0) .827
.591 .591
(12.2) (12.2)
.480 (12.2)
.480 .480
(4.0) (4.0)
Tactiles
.157 (4.0)
.157 .157
Tilt
Lens/Insert
Colors Available: Translucent White Insert
Indicators
JB Clear/White
Translucent White Seal/Diffuser
Accessories
D112 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
BICOLOR LED & LED CAPS
Rockers
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Pushbuttons
Electrical Specifications for Bicolor LED
Programmable Illuminated PB
2CF Maximum Forward Current IFM 60 60 20 12 mA
Red/Green D
Typical Forward Current IF 45 45 15 10 mA
Current Reduction Rate Above 25°C ∆IF 0.80 –––– –––– –––– mA/°C
Keylocks
AT621 AT621 AT621
Bicolor LED (+) (-)
Bicolor LED (+) (-) Bicolor LED (+) (-)
Rotaries
without Resistor with Resistor with Resistor Reverse polarity for Green
LED Caps
Slides
AT3004 AT3005 AT3006
Square Round Rectangular
(21.0)
(15.0) Sq (15.0) Dia .827
.591 (15.0)
.591
Tactiles
.591
Tilt
Transparent Clear Lens
Touch
Lens/Insert
Colors Available:
Transparent White Insert
Indicators
JB Clear/White
Materials:
Supplement
Lens & Insert: Polycarbonate Seal/Diffuser: Thermoplastic Elastomer Bicolor LED AT621
www.nkkswitches.com D113
Series YB Short Body Pushbuttons
Toggles
NO
NO
Pushbuttons
2 L 5
(9.7)
-+
.382
1 4
(2.8) Typ COM
.110
.020
NC
3 6
NO
NO
2 L 5
(9.7)
-+
.382
1 4
(2.8) Typ COM
.110
Rotaries
.591 2 L 5
(9.7)
(18.0) -+
.382
Tilt
(1.2) R
.047
(16.0) +– 0.0
0.2
Dia (16.0) +– 0.0
0.2
Dia
.630 .630
D114 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
OPTIONAL ACCESSORIES
Dust Covers and Protective Guards reduce depth of switch behind panel by .047” (1.2mm).
Panel Thickness Range with Dust Cover or Protective Guards:
Rockers
Bushing Mounting Snap-in Mounting Panel Seal
.020” ~ .150” (0.5mm ~ 3.8mm) .020” ~ .091” (0.5mm ~ 2.3mm) .020” ~ .118” (0.5mm ~ 3.0mm)
Pushbuttons
Dust/Splash Cover (16.2)
.638
AT4115 Dust Cover
for Snap-in or Dust Cover Splash Cover (5.9)
.232
Bushing Mount
Programmable Illuminated PB
AT4115 AT089 AT4115
D
AT541
(5.2)
.205
AT4115 Splash Cover
and AT541 O-ring
for Bushing Mount (23.2)
(29.2)
1.150
.913
AT4115
(16.0) Dia
.630
Materials: Snap-in Mount Panel Seal
Lid: Polyvinyl Chloride
Keylocks
Base: Polyamide Note: AT089 o-ring supplied (20.0) Dia
.787
O-ring: Nitrile butadiene rubber with panel seal model. (0.5)
.020
AT541
Rotaries
.047
Opens 90°
Closes manually (12.0)
.472
(22.9)
.902
Slides
Materials:
Lid: Polycarbonate (1.2) (6.6)
Base: Glass Fiber .047 .260
(11.2) (16.0) Dia
Tactiles
(23.9)
Reinforced Polycarbonate .941 .441 .630
Tilt
Opens 180°
Closes automatically
(12.5)
.492
(23.4)
.921
Touch
(16.0) Dia
.630
.047
(23.9) (11.4) (16.0) Dia
AT4175 .941 .449 .630
(12.5) 180°
.492
Accessories
(23.4)
.921
Materials:
Lid: Polycarbonate
(23.9)
Base: Glass Fiber Reinforced Polyamide
Supplement
.941
(24.0) Min
.945
Coil Spring: Stainless Steel
* Minimum dimension allows opening of cover to 180°
www.nkkswitches.com D115
Series YB Short Body Pushbuttons
Toggles
OPTIONAL ACCESSORIES
Adaptors
Rockers
(17.1) (17.1)
AT716 .673 AT717 .673
Single Pole Double Pole
Solder Lug/ (17.0)
Solder Lug/ (17.0)
Quick Connect .669 Quick Connect .669
Pushbuttons
Terminals Terminals
(5.0) (5.0)
.197 .197
Programmable Illuminated PB
NC NC
(4.85) Typ (4.85) Typ
D NO L NO NO L NO
.191 .191
– + – +
COM COM
(17.1)
Keylocks
(17.1) .673
.673
AT718 AT719
Single Pole Double Pole
(17.0)
Straight PC (17.0)
.669
Straight PC .669
Terminals Terminals
Rotaries
(4.0)
(4.0) .157
.157
NC NC
(4.85) Typ (4.85) Typ
Slides
NO L NO NO L NO
.191 .191
– + – +
(1.85) Typ (1.0) Dia Typ (1.85) Typ (1.0) Dia Typ
.073 .039 .073 .039
(3.0) Typ (3.0) Typ
.118 (5.55) .118 (5.55) Typ
.219 .219
Tilt
CL CL
Dimension A:
Solder Lug .197” (5.0mm); Straight PC .157” (4.0mm)
Accessories
D116 www.nkkswitches.com
Short Body Pushbuttons Series YB
Toggles
ASSEMBLY INSTRUCTIONS
Cap Assembly LED Polarity & Orientation in Lamp Socket
Rockers
Spot ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Plunger
Pushbuttons
Projections
Positive
Lamp Socket Flat
Negative Flat Flat
Switch Lamp Socket (+) (+) (+)
(-) (-) (+)
Body Part Number (-) (-)
Programmable Illuminated PB
Top View of Switch
LED LEDs LED
Spot Illuminated Cap AT628 AT625G AT621 D
with Built-in LED AT634 AT631B AT632F
The following installation tools are available: AT106 Socket Wrench for bushing mounting (Overtightening the mounting nut AT092
may damage the switch housing.); AT109 Cap Extractor; AT111 Lamping Tool.
Further details and dimensions are shown in the Accessories and Hardware section.
LEGENDS
Keylocks
NKK Switches can provide custom legends for caps. Contact factory for more information.
Rotaries
Suggested Printable Area for YB Lens
Recommended Methods: Laser Etch on clear lens, Screen Print or Pad Print on Lens.
Epoxy based ink is recommended.
Slides
ON
(13.48) (15.0)
.531 .591
Tactiles
(13.48) Sq (0.76) Typ (13.48) Dia (0.76) Typ (0.76) Typ (19.48) (0.76) Typ
.531 .030 .531 .030 .030 .767 .030
(15.0) Sq (15.0) Dia (21.0)
.591 .591 .827
Tilt
Shaded areas are printable areas.
Touch
Lens
Filter
(9.88) (11.4) (10.68) (12.2)
.389 .449 .420 .480
Accessories
Seal
(10.68) Sq (0.76) Typ (0.76) Typ (10.68) (0.76) Typ (0.76) Typ (16.68) (0.76) Typ
.420 .030 .030 .420 .030 .030 .657 .030
(12.2) Sq (18.2)
Cap .480 (12.2) .717
Base .480
Supplement
www.nkkswitches.com D117