Professional Documents
Culture Documents
1) Td-Lte-Enodeb-Lte/Td-Qualcomm Ue Limited Service Issue (Attach Not Initiating)
1) Td-Lte-Enodeb-Lte/Td-Qualcomm Ue Limited Service Issue (Attach Not Initiating)
When UE inserted in laptop it receive signal from other network (vendor) initially then after UE
received our home network signal it will not initiate attach request.
until unplug and plug the UE.
Networking Environment
For example vendor1, vendor2 vendor 3, ZTE all are radiating same frequency signal
(EARFCN=38800).
UE initially receives vendor 1 signal after that receives ZTE network signal UE will not attach with our
network.
Even UE will not initiate attach procedure.
Because UE tried to attach with (first received vendor network) vendor 1 that time vendor network
forced UE entered in a Limited service.
So UE will not perform any action only it will receive signals(almost dead state).
Solution
Networking Environment
From Test UE terminal the signal trace on layer 3 is captured shown below.
Laptop & UE is normal.
Solution
TD LTE UE terminal is limited to 29 Mbps in single user cell. At peak 29 Mbps UE disconnects
Networking Environment
eNb with single user in one Cell after 29 Mbps gets disconnected. Transmission is microwave of
ceragon Hybrid IDU Switch. Microwave IDU has capacity of 180Mbps.
Solution
Microwave bandwidth configuration verified & found the bandwidth is restricted to only 32 Mbps every
Node.
Shaper of Microwave for every node not allowing to beyond 29Mbps.
Configuration has been changed CIR is made 1Mbps & PIR has been removed from Configuration.
Shaper is disabled.
Solution
According to the signaling in EPC,nothing come from eNodeB;so we have to check the S1
connection。in S1 Interface,the following parameters need to be checked
1> IP address both in MME and eNodeB
2> SCTP port
3> IP connection(we can ping each other)
4> TA(trace area)
We can get the S1 status from eNodeB,because of MME will be used for server end;MME is not
available from eNodeB after checking 1、2 and 3;TA is not the same between eNodeB and MME after
checking 4;S1 can work fine after we change the TA
Solution
(1)get the information of the black box from the plat staff;
(2)check the optical fiber cable between BBU and RRU;
(3)change RRU.
7) TD-LTE RRU Power-On Self-Test Failure alarm
Solution
the RRU Power-On Self-Test Failure term can't get through
(1)loggin the RRU, enter ushell,input showPowerOnCheck,if there is shown Filter Type Check Error! or
Filter Type Verify Error!,it means that
the Power-On filter bandwidth test failure,or we have to change RRU;
(2)If there is Power-On filter bandwidth test failure,and there appear VSWR alarm with this RRU,at
this time we have to check the antenna of this site;
(3)If there is Power-On filter bandwidth test failure,but there is no VSWR alarm with this RRU,we can
input BspCheckFilter to retest the filter,if the Self-Test Failure disappear,it means the antenna doesn't
connect well when the RRU is power on;
(4)if after retest filter the alarm is still exist,we have to collect the log to send to R&D to analyse.
Solution
(1)Check if RRU or BPL has abnormal alarm;
(2)Check if configure SCTP, IP, adjacent NE;
(3)Check if connecting ling between RRU and BPL is usable, if interface lose;
(4)Check if running version is correct.
Solution
(1)Number 21 port of remote PC be occupied, during LMT login process, BBU need to use database file
in LMT attached ftp server. In this case, mitigation method as following: open PC task manager to
check if there has boot other ftp server process, name such as „ftpserver‟, if yes, close this process,
then restart EOMS. If can‟t find other ftp server process in task manager, can reboot PC;
(2)BBU appear failure, can attempt login BBU using ftp command of cmd.
Solution
(1)Check background if fiber RF resource configured, make sure have configured;
(2)Check if fiber module inserted in RF resource configured optical port, make sure fiber module
inserted optical port is configured optical port;
(3)Check if physical connection is normal, if corresponding optical port light on baseband board flick in
a rate of 1MHz, if corresponding light not flash insert two fiber reversely, if constant flash mean RRU is
booting.
eNB has configured with three interfaces like S1_ControlPlane, S1_UserPlane & OAM_IP
S1_CP IP can be able to ping the MME but S1_UP IP cannot able to ping the SGW IP.
Networking Environment
eNB is normal no alarm.
Solution
1) Check the IP configuration of eNB in OMC
2) Three different interface have three gateway
3) eNB not support the Vrf function & have single default gateway
4) Two differentiate the Interface Static route should be added for next two Interface S1_UP & OAM
5) Add the static route for S1_UP & OAM
Summary and notes
eNB not support Vrf function & two support 3 interface on one physical interface require static route to
differentiate the defaulte gateway of each interface as next hop.
AIX boot into multi-user (NORMAL) and single user (SERVICE) to guide two. Multi-user (NORMAL)
guide: the host liquid crystal display panel "OK" case, pressing thefront panel of the white power
button; single-user (SERVICE) guide: the first system, the AIX CD into the CDROM, press the host
before the white power button panel, the display appears on the screen after the second tone before
the horn sounds, press the "5" key.
System shutdown command and order:
1. The application and database system in order to stop;
2. Use # shutdown command;
# Shutdown System, broadcasting system preparing to shut down the message and shut down after
one minute.
# Shutdown-r System, broadcasting system preparing to shut down the message and shut down after
one minute.When the automatic power-off immediately after.
# Shutdown-F Shut down system immediately.
# Shutdown-Fr Reboot the system immediately.
lsdev command
This command is used to view system device information.
# Lsdev-Cc device type
Commonly used equipment types: processor, disk, adapter, tape, memory, tty, etc.Lsdev-Cc
processor below shows the display results.
b) lspv command
This command is used to view information on the system hard disk.
c) lscfg command
This command is used to view the device configuration information.
# Lscfg-vl device name
Below lscfg-vl hdisk0 display results.
d) lsattr command
The command to the device attribute information.
# Lsattr-El device name
Lsattr-El rmt0 below shows the display results.
# Lsvg VG Name
View the VG (volume group), including PP size, number, has been used (allocated) space, free space
and other information.
# Lsvg-l VG Name
View the VG (Volume Group) has defined logical volume.
Below lsvg-p datavg and lsvg-l datatvg display results.
# Lsvg-o | lsvg-il
List all mount the logical volume.Below is the command displays the results.
c) mount
This command is used to view the installed file system.Below is the command to display information.
b) ifconfig
# Ifconfig name of the NIC ip address
Modify the network card ip address.
c) smitty tcpip
This command is used to modify the network card ip address.
b) smitty clstop
The command to stop the HACMP.
Choose graceful stop HACMP
Select the takeover to stop the machine HACMP, native applications from the standby machine to take
over
Choose forced forced to stop the machine HACMP
Nodes and CLUSTER green for normal, red is down or not up HACMP, yellow in the HACMP unstable,
may be a node HACMP is started, switch, stop.
d) check the output of HACMP
# Tail-f / tmp / hacmp.o
HACMP is started, use this command to view the file show whether the error
e) Check the address information
# Netstat-i
Use this command to check the type of network card binding address is correct, three types: boot,
service, standby.
f) See logical volume groups and file systems
# Lsvg-o
Should be activated with the command (varyon) of the VG is activated.
# Mount
Use this command should mount the file system is normal.
Incident description
To check the eNB version and SCTP link, one can login to OMC/EMS client and use the Diagnosis tools
but for specific results one can telnet the eNB and use specific commands to check the required items.
Networking Environment
From OMM server telnet on CC board by using the EnodeB IP address.
Before telneting the EnodeB IP address we need to check the connectivity, so first pin
gEnodeB ip address then if it is pinging, proceed with the telnet commend.
start----->cmd
#./ushell
Solution
Incident description
To check the Radio output power and Antenna VSWR, one can login to OMC/EMS client and
use the Diagnosis tools but for instantaneous results one can telnet the eNB and use specific
commands to check the required items.
Networking Environment
telnet 200.6.xxx.xxx
/ushell
zte
ps (ps will show all running processes)
pad 42
Solution
Radio Frequency and Bandwidth configured for RRU can be checked by:
showrf
Antenna vswr for RRU can be checked by:
showvswr
telnet 200.7.xxx.xxx
ushell
zte
ps (ps will show all running processes)
pad 718
Radio power for RRU can be checked by:
ShowPwrDetinfo
BspGetRssiPwr 3,0,0
Summary
This document will help in checking power and vswr values by telnetting the RRU.
Figure 3
Server Cell
RSRQ of
LTE TDD
3 Summary
Eplus site has a good coverage,It can cover 700m in the dense buildings and cover 3km in the open
area(airport);container site is lower(only 3m) and blocked by the surrounding buildings; The section 2 of Eplus
site with the section 3 of container can finish handover,there is no problem of handover test.
During the DT test,we found out that the download speed of R4 and R5 services of two cells on
Shiquan Road in Siming district, xiamen city were too slow. The average speed was 30kbps, but other
services of those cells were normal
We tested the same termination under other normal cells, and the speed was normal which showed
that it was not problems of the termination or the SIM card. On the other hand, as for the difference
between configurations of priority level of different HS services, we checked the stream class, the
interactive class, the background class and the session class, and figured out the problems were the
same. Then we checked the related KPI from OMCR, and the report showed that both cells had every
kind of service, and the established ratio was very good. So the current problem was that the
download speed of HSDPA is too slow.
(1) first, we doubted interference was the cause, so we checked the ISCP and RTWP through
LMT, and the results showed they were both OK.
(2) Excluding interference cause, we suspect there were some problems in the configurations
of such cells.
Solution
We asked the researchers to help, and they found out one parameter was abnormal through signaling
analysis. They asked us to check the configurations of IUB port. Finally, we found there was one
parameter of these cells differed from that of others. We highlighted that as follow: the right
parameter of normal cells is 50, but in the abnormal cells, it is 0.
So we corrected the parameter, and did tests, the speed turned to OK, the download speed of R4
and R5 was normal.
Such problems are typical configuration mistake. Next time, facing such problems, we suggest we
do comparison of the parameters first, and try to find out the difference between normal and
abnormal cells, so we can locate the problems caused by parameters as soon as possible.
During the process of resolving such problems, we found that the parameter do not work out as its
configuration in the RNC, in some cases.
During next DT tests, we also found some cells had the same problem. But when we check the
parameter, we did not find any mistake. The priority level adjusted coefficient in the IUB was 50. We
doubted the parameter do not work out correctly. So we used the signal tracing tool to check this out.
The result is as follow, which indicated that although the parameter is 50, but the actual value is 0.
We reconfigurated the parameter to 50(changed from 50 to 0, then changed 0 to 50), but did not
resolve the problem. The signal tracing tool also showed ik=0, and the download speed of R4 and R5
is still 30kbps.
We tried to change the parameter to 100 first, this time, the ik became 100, and the speed
returned to normal.
Then we modified the parameter to 50, and the ik became 50, the speed remain normal. The
signal is as follow: