Professional Documents
Culture Documents
Especificações Do Bloco Do Motor
Especificações Do Bloco Do Motor
Shutdown SIS
Previous Screen
Welcome: a3yn3412
Product: MAR INE ENGINE
Mode l: C 32 MAR INE ENGINE R NY00807
C onfiguration: C 32 Marine Engine R NY00001-UP
Specifications
C32 Marine and Auxiliary Marine Engines
Media Number -SENR9772-06 Publication Date -01/06/2011 Date Updated -08/06/2011
i05258408
Cylinder Block
SMCS - 1201
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 1/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Illustration 1 g03347646
Front view of the engine
Typical example
Illustration 2 g03347647
Marks for tightening main bearings
Typical example
Table 1
Specification for 350-5438 Cylinder Block Gp and 349-2859 Cylinder Block Gp
Item Qty
Part Specification Description
The top face of the cylinder block, bottom surface of spacer plate (1) and both sides of plate gasket (2) must be
free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly.
225-3100
1 2 Spacer Thickness is 8.585 ± 0.025 mm (0.3380 ± 0.0010 inch).
Plate
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 2/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
354-8484
Thickness of plate gasket that is between cylinder block and spacer plate is
2 2 Plate
0.20 ± 0.02 mm (0.008 ± 0.001 inch).
Gasket
7C-9614 Before assembly, apply Loctite low breakloose PST on the threads.
3 4 Taperlock Torque to
Plug 80 ± 15 N·m (60 ± 11 lb ft).
4N-1650 Extension of the dowels on the left bank and right bank from the cylinder block is
A 4
Dowel 18.5 ± 0.5 mm (0.73 ± 0.02 inch).
232-7607 The crankshaft caps must be installed with the identifying marks toward the front of
4 7 Crankshaft the engine. The number of the main bearing cap must also match the cast number on
Cap the left side of each main bearing saddle.
The distance from the centerline of the crankshaft bearing bore to the top of the
C - - cylinder block is
419.10 ± 0.15 mm (16.500 ± 0.006 inch).
The distance from the centerline of the crankshaft bearing bore to the bottom of the
D - - cylinder block is
165.10 ± 0.10 mm (6.500 ± 0.004 inch).
14 365-4307
5 Use the following procedure to install the crankshaft cap:
Bolt
1. Apply clean engine oil on the threads of the bolts (6) . Loosely install the bolts (6) .
2. Apply clean engine oil on the threads of the side bearing cap bolts (5) and the
washers. Loosely install the side bearing cap bolts (5) and the washers.
5. Put a mark on each bolt (6) and each crankshaft cap (4) . See Illustration 2.
6. Again, tighten opposite end of the main bearing cap bolt from the mark to an
additional angle (F) of 120 ± 5 degrees.
3P-1323
14 Bearing 6. Again, tighten tab end of the main bearing cap bolt from the mark to an additional
6
Cap Bolt angle (F) of 120 ± 5 degrees.
8. Tighten the side bearing cap bolts (5) that are at the opposite end of the main
bearing cap to
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 3/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
9. Tighten the side bearing cap bolts (5) that are at the tab end of the main bearing
cap to
80 ± 10 N·m (60 ± 7 lb ft).
10. Again, tighten the side bearing cap bolts (5) that are at the opposite end of the
main bearing cap to
80 ± 10 N·m (60 ± 7 lb ft).
11. Again, tighten the side bearing cap bolts (5) that are at the tab end of the main
bearing cap to
80 ± 10 N·m (60 ± 7 lb ft).
Illustration 3 g03347648
Right side of the engine
Typical example
Table 2
Specification for 350-5438 Cylinder Block Gp and 349-2859 Cylinder Block Gp
Item Qty
Part Specification Description
214-1728 Stud Apply blue Loctite 540 to the pipe threads of stud. Tighten the stud with the
7 1
coated pipe threads into the cylinder block.
6L-4428
Taperlock Stud Torque to
8 3
35 ± 5 N·m (26 ± 4 lb ft).
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 4/5
3/5/2014 C32 Marine Engine RNY00001-UP(SEBP4767 - 32) - Systems & Components
Extension of dowels from the rear face of the cylinder block and from the front
4N-0683 Dowel
G 4 face of the cylinder block is
19.0 ± 0.5 mm (0.75 ± 0.02 inch).
C opyright 1993 - 2014 C ate rpillar Inc. Sat May 03 2014 11:31:21 GMT-0300 (Hora oficial do Brasil)
All R ights R e se rve d.
Private Ne twork For SIS Lice nse e s. a3yn3412
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/sis… 5/5