Professional Documents
Culture Documents
3500-94M VGA Display Monitor Datasheet - 122M3217
3500-94M VGA Display Monitor Datasheet - 122M3217
Datasheet
Bently Nevada Machinery Condition Monitoring
Description
The 3500/94M VGA module displays all 3500 machinery
protection system information, including:
l System event list
l Alarm event list
l All module and channel data
l Alarm and OK status
l Nine custom display options
Use the 3500 Rack Configuration Software to configure up to
nine custom screens. By default, one bar graph screen shows
all of the 1X-filtered vibration measurements, while another
shows the proximity transducer gap values.
You can organize custom screens into machine train groups.
You can also organize system data into any pages on the
custom screen.
System Components
The 3500/94M is comprised of:
l The 3500/94M VGA module
l An I/O module
l A 10" or 15" VGA touch screen display
You can mount the VGA display monitor using standard cables
up to 6 m (20 ft) from a 3500 rack, or using a supported
Keyboard Video Monitor (KVM) Extender, up to 10 km (6.2
miles) from the 3500 rack.
Document: 122M3217
Rev. G
3500/94M VGA Display Monitor
Datasheet
WARNING
Specifications
HAZARDOUS
3500/94M VGA Display Unit VOLTAGE
Inputs RISK OF ELECTRIC SHOCK,
BURN OR DEATH.
Power
4.6 watts max. Do not remove cover. No user
consumption
servicable parts inside.
High-speed
Monitor status, data and values
network
RS232 port (I/0) Touch controller data
Outputs
Indicates proper operation of the
WARNING
OK LED
module
EXPLOSION
Indicates communications between
TX/RX LED HAZARD
other system modules
Analog red, green, blue and sync signals Refer to User Manual BEFORE
VGA port (I/O) making connections.
to the display
24 Vdc Power out, VGA signal out, DO NOT DISCONNECT
Front Port EQUIPMENT UNLESS POWER
Touch commands in.
HAS BEEN SWITCHED OFF OR
THE AREA IS KNOWN TO BE
Environmental Limits NON-HAZARDOUS.
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE
Operating| -20° C to 65° C
DECONNECTER L'EQUIPMENT, COUPER LE COURANT OU
Temperature (-22° F to 149° F)
S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON
Storage -40° C to 85° C DANGEREUX.
Temperature (-40° F to 185° F)
Humidity 95%, non-condensing
Standards
EN 61000-6-2
EMC EN 61000-6-4
Directive
2014/30/EU
Standards
CSA C22.2 61010-1
Electrical Safety UL EN 61010-1
Directive
2014/35/EU
Directive
RoHS
2011/65/EU
North America
Canada
Ex nC [L] IIC T4 Gc:
Certified to CSA60079-0, -11, -15
Class I, Division 2, Groups A, B, C
and D:
Certified to CSA213
USA
Approval Option (01) Class I, Zone 2: AEx nC IIC T4 Gc:
Conforms to: UL60079-0, -11, -15
Class I, Division 2, Groups A, B, C
and D:
Conforms to ISA 12.12.01
T4 @ -20 °C ≤ Ta ≤ +65 °C
(-4 °F ≤ Ta ≤ +149 °F)
Per control drawing 149243
ATEX/IECEx
II 3 G
Ex nA nC ic IIC T4 Gc
Approval Option (02)
T4 @ -20 °C ≤ Ta ≤ +65 °C
(-4 °F ≤ Ta ≤ +149 °F)
Per control drawing 149243
North America
Canada
Ex ic nA IIC T4;
Certified to CSA C22.2 60079-0,-11,-15
Class I, Division 2, Groups A, B, C, D T4;
Approval Option Certified to CSA C22.2 213
(01) USA
Class I, Division 2, Group A, B, C, D T4;
Conforms to: ISA 12.12.01
Class I, Zone 2, AEx ic nA IIC T4;
Conforms to: UL60079-0, -11, -15
ATEX/IECEx
Approval Option II 3G Ex ic nA IIC T4 Gc;
(02) -20°C ≤ Ta ≤ +65°C
Temperature 0 ºC to 45 ºC
range (32 ºF to 113 ºF)
Humidity 80%, non-condensing
The KVM Extender Receiver is approved
for Class I, Division 2 hazardous areas in
North America.
Class I, Division 2 The KVM Extender Transmitter is not
certified for hazardous usage and must
be installed in a safe area or enclosed in
an approved enclosure (such as a
Inrush Current: 3.5 A @ 24 V (< 500 µs) The minimum temperature rating
is 0 ºC for the screen, front bezel,
Operating Current: < 500 mA and rear electronics. When the
CE, UL, CUL screen or front bezel is exposed to
Agencies
temperatures below 0 ºC, a heated
IP54 Designed for. enclosure is required.
Class I, Div 2 Yes Humidity 95% RH
ATEX/IECEx Yes Touch Interface Resistive
Temperature 0 to 65 °C operating temperature. Manufacturer Advantech
The minimum temperature rating Dimensions (W x 422 mm (16.61 in) x 338 mm (13.31 in) x
is 0 ºC for the screen, front bezel, H x D) inches 68.0 mm (2.68 in)
and rear electronics. When the
screen or front bezel is exposed to Panel Cutout: 396 mm (15.59 in) X 296
temperatures below 0 ºC, a heated mm (11.65 in)
enclosure is required Weight Shipping 8.5 kg (18.74 lb)
Humidity 10% to 85% RH non-condensing
Warranty Two years
Touch Interface GFG Resistive Touch Screen
Advantech Recommended for industrial use. Not certified for
Manufacturer
hazardous locations.
Dimensions 387.4 mm (15.25 in) x 248.9 mm (9.8 in) x
(W x H x D) 49.0 mm (1.93 in)
Panel Cutout: 355.6 mm (14.0 in) x 241.3
mm (9.5 in)
Weight Shipping 4.0 kg (8.78 lb)
Ordering Preparation
The 3500/94M requires the 3500/22 Transient l Advantech 10” touch screen display
Data Interface (TDI) module. It also requires (P/N 120M8155-01)
these or newer versions of the following l Advantech 15” touch screen display
firmware and software: (P/N 102M8950)
l Parker touch screen displays (P/N 148653-
3500/94M Firmware 4.06, Rev. C 01 - no longer available).
3500/22 Firmware (TDI) Rev 1.71
3500/01 Software (Rack Config) Rev 5.6
3500/02 Software (Op Display) Rev 2.21
3500/03 Software (Data
Rev 1.22
Acquisition)
01
Wired CAT5 UTP KVM extender and cable 250 ft For display monitor specifications, See "Display
(76.2 m) Monitor Specifications" on page 6.
Wired CAT5 UTP KVM extender and cable 500 ft
02
(152.4 m) ANA-D3510-100-A1, Advantech 10”
Wired CAT5 UTP KVM extender and cable 1,000 ft 120M8155-01 display. Does not include mounting
03 screws.
(304.8 m)
12 Display Router Box cable 20 ft (6 m) Front Mounting Accessories and Spares
SM FO KVM SNGL extender and cable 94M face mount for Advantech 10”
20 122M3368-01
2,000' (609.6 m) display
SM FO KVM SNGL extender and cable Mounting standoff for face mount
21 display with threaded mounting holes
4,000' (1219.2 m)
for 19" EIA rack.
SM FO KVM SNGL extender and cable
22 AA: mounting hole thread size. Choose
6,000' (1828.8 m) 122M4631-AA
one:
SM FO KVM SNGL extender and cable
23
8,000' (2438.4 m) 01 – M6 x 1
24 SM FO KVM SNGL extender with patch cables 02 – 10-32
03 – M5 x 0.8
SM FO KVM DUAL extender and cable
25 3 ft (.91 m) v Video, serial, and power
2,000' (609.6 m)
cable from front of rack-mounted
SM FO KVM DUAL extender and cable 3500/94M Module to the 10" Advantech
26 107M3696-01
4,000' (1219.2 m) display. Note that cable assembly
SM FO KVM DUAL extender and cable 119M6503-03 is also required from the
27 3500/94M IO Module (190214-02) to an
6,000' (1828.8 m)
KVM CAT5 UTP Extender Accessories and Spares 128M4552 SM FO patch cable 20 ft (6.1 m)
Figure 3: Single Rack with Wired (UTP CAT5) Keyboard Video Monitor (KVM) Extender
† Engineering approval is required for Class I Division 2 UTP CAT5 KVM Extender Installations in North America. The
KVM Extender transmitter must be installed in a safe area. ATEX/IECEx approval is not available for the UTP CAT5 KVM
Extender.
Third and Fourth Rack - router cable for each additional rack
Ordering Option Description
3500/94M-00-12-(00/01/02) Rack-to-router cable
The SM FO KVM receiver and transmitter are not certified for hazardous area installations. Both the receiver and the
transmitter must be installed in a safe area or enclosed in an approved enclosure.