Professional Documents
Culture Documents
NJM8530/NJM8532/NJM8534: 14V, 10nV/√Hz, 300μA/ch, Rail-to-Rail Input/Output Operational Amplifier
NJM8530/NJM8532/NJM8534: 14V, 10nV/√Hz, 300μA/ch, Rail-to-Rail Input/Output Operational Amplifier
Package
Ver.03 [ 1]
NJM8530/NJM8532/NJM8534
BLOCK DIAGRAM
V+
+INPUT
OUTPUT
-INPUT
V-
(3) (4)
Power Dissipation 2-layer / 4-layer 400 SSOP8
SOT-23-5 480 / 650
300
DMP8 470 / 600
PD mW
SSOP8 430 / 540 200
MSOP8(TVSP8) 510 / 680
SSOP14 500 / 620 100
(1) Differential voltage is the voltage difference between +INPUT and -INPUT.
(2) The inputs are protected by diodes. If the differential input voltage exceeds 1.0V, the input current must be limited 2 mA or less
by using a restriction resistance.
Input voltages outside the supply voltage will be clamped by ESD protection diodes. If the input voltage exceeds the supply
voltage, the input current must be limited 2 mA or less by using a restriction resistance.
(3) Power dissipation is the power that can be consumed by the IC at Ta=25°C, and is the typical measured value based on
JEDEC condition. When using the IC over Ta=25°C subtract the value [mW/°C]=PD/(Tstg(MAX)-25) per temperature.
(4) 2-layer: EIA/JEDEC STANDARD Test board (76.2x114.3x1.6mm, 2-layers, FR-4) mounting
4-layer: EIA/JEDEC STANDARD Test board (76.2x114.3x1.6mm, 4-layers, FR-4) mounting
Ver.03 [ 2]
NJM8530/NJM8532/NJM8534
■ ELECTRICAL CHARACTERISTICS (V+=5V, V-=0V, VCOM=2.5V, Ta=25°C, unless otherwise noted.)
PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
INPUT CHARACTERISTICS
Input Offset Voltage VIO - 1 4 mV
Input Offset Voltage Drift ΔVIO/ΔT Ta=-40°C to +125°C - 1.5 - µV/°C
Input Bias Current IB - 50 250 nA
Input Offset Current IIO - 5 100 nA
Open-Loop Voltage Gain AV RL=2kΩ to 2.5V 60 85 - dB
(5)
Common-Mode Rejection Ratio CMR 55 70 - dB
Common-Mode Input Voltage Range VICM CMR≥55dB 0 - 5 V
OUTPUT CHARACTERISTICS
RL=20kΩ to 2.5V 4.9 4.95 - V
High-level Output Voltage VOH
RL=2kΩ to 2.5V 4.75 4.85 - V
RL=20kΩ to 2.5V - 0.05 0.1 V
Low-level Output Voltage VOL
RL=2kΩ to 2.5V - 0.15 0.25 V
Sourcing - 20 - mA
Short-Circuit Output Current ISC
Sinking - 5 - mA
POWER SUPPLY
Supply Current (All Amplifiers) No Signal
NJM8530 - 320 550 μA
ISUPPLY
NJM8532 - 580 900 μA
NJM8534 - 1200 1800 μA
+
Supply Voltage Rejection Ratio SVR V =4V to 6V 70 85 - dB
AC CHARACTERISTICS
Slew Rate SR RL=2kΩ to 2.5V - 0.4 - V/μs
Gain Bandwidth Product GBW RL=2kΩ to 2.5V - 1 - MHz
Phase Margin Φm RL=2kΩ to 2.5V - 75 - Deg
Equivalent Input Noise Voltage en f=1kHz - 10 - nV/√Hz
Channel Separation f=1kHz, Vo=1.2Vrms
CS
NJM8532/NJM8534 - -133 - dB
(5) CMR specified is the lower of the CMR+ and CMR-.
+ + - +
CMR+ measured with V /2≤VCM≤V , and CMR- measured with V ≤VCM≤V /2.
Ver.03 [ 3]
NJM8530/NJM8532/NJM8534
■ ELECTRICAL CHARACTERISTICS (V+=3V, V-=0V, VCOM=1.5V, Ta=25°C, unless otherwise noted.)
PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
INPUT CHARACTERISTICS
Input Offset Voltage VIO - 1 4 mV
Input Offset Voltage Drift ΔVIO/ΔT Ta=-40°C to +125°C - 1.8 - µV/°C
Input Bias Current IB - 50 250 nA
Input Offset Current IIO - 5 100 nA
Open-Loop Voltage Gain AV RL=2kΩ to 1.5V 60 84 - dB
(5)
Common-Mode Rejection Ratio CMR 48 63 - dB
Common-Mode Input Voltage Range VICM CMR≥48dB 0 - 3 V
OUTPUT CHARACTERISTICS
RL=20kΩ to 1.5V 2.9 2.95 - V
High-level Output Voltage VOH
RL=2kΩ to 1.5V 2.75 2.85 - V
RL=20kΩ to 1.5V - 0.05 0.1 V
Low-level Output Voltage VOL
RL=2kΩ to 1.5V - 0.15 0.25 V
Sourcing - 18 - mA
Short-Circuit Output Current ISC
Sinking - 4.8 - mA
POWER SUPPLY
Supply Current (All Amplifiers) No Signal
NJM8530 270 460 μA
ISUPPLY
NJM8532 - 510 880 μA
NJM8534 - 1000 1800 μA
+
Supply Voltage Rejection Ratio SVR V =2.4V to 4V 68 83 - dB
AC CHARACTERISTICS
Slew Rate SR RL=2kΩ to 1.5V - 0.35 - V/μs
Gain Bandwidth Product GBW RL=2kΩ to 1.5V - 1 - MHz
Phase Margin Φm RL=2kΩ to 1.5V - 75 - Deg
Equivalent Input Noise Voltage en f=1kHz - 10 - nV/√Hz
Channel Separation f=1kHz, Vo=0.7Vrms
CS
NJM8532/NJM8534 - -130 - dB
(5) CMR specified is the lower of the CMR+ and CMR-.
+ + - +
CMR+ measured with V /2≤VCM≤V , and CMR- measured with V ≤VCM≤V /2.
Ver.03 [ 4]
NJM8530/NJM8532/NJM8534
■ ELECTRICAL CHARACTERISTICS (V+=1.8V, V-=0V, VCOM=0.9V, Ta=25°C, unless otherwise noted.)
PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
INPUT CHARACTERISTICS
Input Offset Voltage VIO - 1 4 mV
Input Offset Voltage Drift ΔVIO/ΔT Ta=-40°C to +125°C - 2.4 - µV/°C
Input Bias Current IB - 50 250 nA
Input Offset Current IIO - 5 100 nA
Open-Loop Voltage Gain AV RL=2kΩ to 0.9V 60 83 - dB
(5)
Common-Mode Rejection Ratio CMR 40 55 - dB
Common-Mode Input Voltage Range VICM CMR≥40dB 0 - 1.8 V
OUTPUT CHARACTERISTICS
RL=20kΩ to 0.9V 1.7 1.75 - V
High-level Output Voltage VOH
RL=2kΩ to 0.9V 1.55 1.65 - V
RL=20kΩ to 0.9V - 0.05 0.1 V
Low-level Output Voltage VOL
RL=2kΩ to 0.9V - 0.15 0.25 V
Sourcing - 18 - mA
Short-Circuit Output Current ISC
Sinking - 4.7 - mA
POWER SUPPLY
Supply Current (All Amplifiers) No Signal
NJM8530 240 430 μA
ISUPPLY
NJM8532 - 460 800 μA
NJM8534 - 900 1600 μA
+
Supply Voltage Rejection Ratio SVR V =1.8V to 2.4V 65 80 - dB
AC CHARACTERISTICS
Slew Rate SR RL=2kΩ to 0.9V - 0.3 - V/μs
Gain Bandwidth Product GBW RL=2kΩ to 0.9V - 1 - MHz
Phase Margin Φm RL=2kΩ to 0.9V - 75 - Deg
Equivalent Input Noise Voltage en f=1kHz - 10 - nV/√Hz
Channel Separation f=1kHz, Vo=0.4Vrms
CS
NJM8532/NJM8534 - -125 - dB
(5) CMR specified is the lower of the CMR+ and CMR-.
+ + - +
CMR+ measured with V /2≤VCM≤V , and CMR- measured with V ≤VCM≤V /2.
Ver.03 [ 5]
NJM8530/NJM8532/NJM8534
■ TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
Supply Current per Amplifier vs. Supply Voltage Supply Current per Amplifier vs. Temperature
GV=0dB GV=0dB
600 600
Supply Current per Amplifier [μA]
Ta=25ºC
400 400
300 300
Ta=125ºC
200 200
Ta=-40ºC
0 0
0 +2 +4 +6 +8 +10 +12 +14 -50 -25 0 25 50 75 100 125 150
Supply Voltage V+ [V] Ambient Temperature [ºC]
Input Offset Voltage vs. Supply Voltage Input Offset Voltage vs. Temperature
VCOM=V+/2 VCOM=V+/2
2.0 2.0
1.6 1.6
1.2 1.2
Input Offset Voltage [mV]
-2.4 -2.4
-2.8 -2.8
0 2 4 6 8 10 12 14 -50 -25 0 25 50 75 100 125 150
Supply Voltage [V] Ambient Temperature [ºC]
30% 30%
Number of Amplifiers
Number of Amplifiers
25% 25%
20% 20%
15% 15%
10% 10%
5% 5%
0% 0%
-2.4 -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 -2.4 -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2
Input Offset Voltage [mV] Input Offset Voltage [mV]
Ver.03 [ 6]
NJM8530/NJM8532/NJM8534
■ TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
40%
30%
35%
Number of Amplifiers
Number of Amplifiers
25%
30%
20% 25%
15% 20%
15%
10%
10%
5%
5%
0% 0%
-2.4 -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 -6.0 -4.0 -2.0 0.0 2.0 4.0 6.0 8.0 10.0
Input Offset Voltage [mV] Input Offset Voltage Drift [μV/ºC]
Input Offset Voltage Drift Distribution Input Offset Voltage Drift Distribution
V+=5V, VCOM=V+/2 V+=1.8V, VCOM=V+/2
40% 40%
35% 35%
30% 30%
Number of Amplifiers
Number of Amplifiers
25% 25%
20% 20%
15% 15%
10% 10%
5% 5%
0% 0%
-6.0 -4.0 -2.0 0.0 2.0 4.0 6.0 8.0 10.0 -6.0 -4.0 -2.0 0.0 2.0 4.0 6.0 8.0 10.0
Input Offset Voltage Drift [μV/ºC] Input Offset Voltage Drift [μV/ºC]
1.0 1.0
Input Offset Voltage [mV]
Ta=125ºC
Ta=125ºC
0.0 0.0
-1.0 -1.0
Ta=-40ºC
-2.0 -2.0
Ta=25ºC
Ta=25ºC
-3.0 -3.0 Ta=-40ºC
-4.0 -4.0
-1 0 2 4 6 8 10 12 14 -1 0 1 2 3 4 5 6
Common-Mode Input Voltage [V] Common-Mode Input Voltage [V]
Ver.03 [ 7]
NJM8530/NJM8532/NJM8534
■ TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
200
1.0
Input Offset Voltage [mV]
Ta=-40ºC
-1.0 50
0
-2.0
Ta=125ºC
-50
-3.0
-100
Ta=-40ºC
-4.0 -150
-0.6 0 0.6 1.2 1.8 2.4 -1 0 1 2 3 4 5 6
Common-Mode Input Voltage [V] Common-Mode Input Voltage [V]
Input Bias Current vs. Temperature Open-Loop Voltage Gain vs. Temperature
VCOM=V+/2 RL=2kΩ to V+/2
250 120
200
Open-Loop Voltage Gain [dB]
V+=14V V+=5V
100
Input Bias Current [nA]
100 80
50
0 60
V+=1.8V
-50 V+=1.8V
40
-100
-150 20
-50 -25 0 25 50 75 100 125 150 -50 -25 0 25 50 75 100 125 150
Ambient Temperature [ºC] Ambient Temperature [ºC]
Common Mode / Supply Voltage Rejection Ratio Maximum Output Voltage vs. Output Current
vs. Temperature V+=14V
120 14
13
ISOURCE
Common Mode / Supply Voltage
12
Maximum Output Voltage [V]
Ta=-40ºC
100 CMR(V+=14V) SVR 11
Rejection Ratio [dB]
10 Ta=25ºC
9
80 Ta=125ºC
8
7
6 Ta=125ºC
60
5
4 Ta=25ºC
40 CMR(V+=5V) 3
CMR(V+=1.8V) 2 Ta=-40ºC
1
ISINK
20 0
-50 -25 0 25 50 75 100 125 150 0.1 1 10 100
Ambient Temperature [ºC] Output Current [mA]
Ver.03 [ 8]
NJM8530/NJM8532/NJM8534
■TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
Maximum Output Voltage vs. Output Current Maximum Output Voltage vs. Output Current
V+=5V V+=1.8V
5.0 1.8
4.5 ISOURCE 1.6 ISOURCE
Ta=-40ºC
Maximum Output Voltage [V]
1.0 0.4
Ta=-40ºC
Ta=-40ºC
0.5 0.2
ISINK ISINK
0.0 0.0
0.1 1 10 100 0.1 1 10 100
Output Current [mA] Output Current [mA]
Maximum Output Voltage vs. Load Resistance Maximum Output Voltage vs. Load Resistance
V+=14V, Gv=open, RL connected to 0V V+=5V, Gv=open, RL connected to 0V
14 5
VOH
Low-level Output Voltage VOL [mV]
12 Ta=125ºC
Ta=-40ºC
4 Ta=125ºC
Ta=-40ºC
10
Ta=25ºC 3
8
Ta=25ºC
5
6 6
Ta=-40ºC 2 4
Ta=-40ºC
4 Ta=125ºC 4 VOL 3
VOL
1 2
2 2
Ta=125ºC
1
Ta=25ºC Ta=25ºC
0 0 0 0
10 100 1k 10k 100k 10 100 1k 10k 100k
Load Resistance [Ω] Load Resistance [Ω]
Maximum Output Voltage vs. Load Resistance Maximum Output Voltage vs. Load Resistance
V+=1.8V, Gv=open, RL connected to 0V V+/V-=±7V, Gv=open, RL connected to 0V
1.8 7
6
Low-level Output Voltage VOL [mV]
Ta=125ºC
High-level Output Voltage VOH [V]
1.6
VOH 5
Maximum Output Voltage [V]
Ta=125ºC Ta=25ºC
1.4 Ta=-40ºC 4
3
1.2 2
Ta=-40ºC
1.0 1
Ta=25ºC 0
0.8 4 -1 Ta=25ºC
Ta=-40ºC -2
0.6 VOL 3
-3
Ta=-40ºC
0.4 2 -4 Ta=125ºC
-5
0.2 1
Ta=125ºC -6
Ta=25ºC
0.0 0 -7
10 100 1k 10k 100k 10 100 1k 10k 100k
Load Resistance [Ω] Load Resistance [Ω]
Ver.03 [ 9]
NJM8530/NJM8532/NJM8534
■TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
Maximum Output Voltage vs. Load Resistance Maximum Output Voltage vs. Load Resistance
V+/V-=±2.5V, Gv=open, RL connected to 0V V+/V-=±0.9V, Gv=open, RL connected to 0V
2.5 0.9
2.0
Maximum Output Voltage [V]
-2.5 -0.9
10 100 1k 10k 100k 10 100 1k 10k 100k
Load Resistance [Ω] Load Resistance [Ω]
40dB Voltage Gain/Phase vs. Frequency 40dB Voltage Gain/Phase vs. Frequency
V+=14V, Gain=40dB, RL=2kΩ to 7V, Ta=25ºC V+=5V, Gain=40dB, RL=2kΩ to 2.5V, Ta=25ºC
40 40
Voltage Gain Voltage Gain
20 CL=0pF 20 CL=0pF
Voltage Gain [dB]
Phase [deg]
Phase Phase
0 0 0 0
CL=1000pF
CL=1000pF
CL=470pF
CL=470pF
CL=220pF
-20 -60 -20 CL=220pF -60
CL=0pF
CL=0pF
CL=0pF V+=14V
20 2.0
Voltage Gain [dB]
Phase [deg]
GBW [MHz]
0
Phase
0 1.6
CL=1000pF
CL=470pF 1.2
-20 CL=220pF -60
CL=0pF
0.8 V+=5V
Ver.03 [ 10]
NJM8530/NJM8532/NJM8534
■TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
90
15
85 CL=2200pF
Phase Margin [deg]
V+=14V
65 0 CL=220pF
V+=5V
60
V+=1.8V -5 CL=10pF
55
50 -10
-50 -25 0 25 50 75 100 125 150 10k 100k 1M 10M 100M
Ambient Temperature [ºC] Frequency [Hz]
15 15 CL=2200pF
CL=2200pF
Voltage Gain [dB]
10 10 CL=1000pF
CL=1000pF
CL=470pF
5 CL=470pF 5
0 CL=220pF 0 CL=220pF
CL=10pF
-5 CL=10pF -5
-10 -10
10k 100k 1M 10M 100M 10k 100k 1M 10M 100M
Frequency [Hz] Frequency [Hz]
20 20
Overshoot [%]
15 15
V+=14V
10 V+=5V 10
V+=1.8V
5 5
0 0
100p
100 1n
1k 10n
10k 1 10 100 1k 10k 100k
Capacitive Load [F] Frequency [Hz]
Ver.03 [ 11]
NJM8530/NJM8532/NJM8534
■TYPICAL CHARACTERISTICS (V-=0V, Ta=25°C, unless otherwise noted.)
0.8
V+=5V V+=14V
Voltage [0.5V/div]
CL=10pF 0.4
CL=1000pF
0.2
V+=1.8V
0.0
Time [5μs/div] -50 -25 0 25 50 75 100 125 150
Ambient Temperature [ºC]
No Phase Reversal
THD+N vs. Output Voltage V+=5V, f=10kHz, VIN=6VP-P
V+=3V, GV=+2, RL=2kΩ to 1.5V, CL=0pF, Ta=25ºC Gv=0dB, RL=2kΩ to V+/2
10
Total Harmonic Distortion + Noise [%]
input
1
Voltage [0.5V/div]
f=10kHz
0.1
f=1kHz
Ta=-40ºC
0.01 Ta=25ºC
Ta=125 ºC
f=100Hz
0.001
0.001 0.01 0.1 1 10 Time [1μs/div]
Output Voltage [Vrms]
-80
Channel Separation [dB]
-100 V+=3V
V+=1.8V
-120
-140
V+=5V
-160
10 100 1k 10k 100k
Frequency [Hz]
Ver.03 [ 12]
NJM8530/NJM8532/NJM8534
■ APPLICATIONS INFORMATION
Single and Dual Supply Voltage Operation Input Offset Voltage
vs. Common-Mode Input Voltage
The NJM8530/NJM8532/NJM8534 works with both V+=5V
2.0
single supply and dual supply when the voltage
+ −
supplied is between V and V . These amplifiers
1.0
operate from single +1.8 to +14V supply and dual
Ver.03 [ 13]
NJM8530/NJM8532/NJM8534
■ APPLICATIONS INFORMATION
Capacitive load The differential amplifier’s common-mode rejection
The NJM8530/NJM8532/NJM8534 can use at unity ratio (CMR) is primarily determined by resistor
gain follower, but the unity gain follower is the most mismatches, not by the op-amp’s CMR. Ideally, the
sensitive configuration to capacitive loading. The resistors are chosen such that R2/R1 = R4/R3. The
combination of capacitive load placed directly on the CMR due to the resistors in differential amplifier can be
output of an amplifier along with the output impedance calculated using the below formula:
of the amplifier creates a phase lag which in turn
R2
reduces the phase margin of the amplifier. If phase CMRR_error ≈ 20log
1+
R1
overshoot and ringing in the step response. CMRR_error =CMR due only to the resistors
The NJM8530/NJM8532/NJM8534 is unity gain stable Rerror =Resistor's tolerance
for capacitive loads of 1000pF (see the overshoot vs.
capacitive load graph). To drive heavier capacitive Example:
loads, an isolation resistor, RISO as shown Figure4, R2/R1=1 and Rerror=0.1%, then CMR=54dB
should be used. RISO improves the feedback loop’s R2/R1=1 and Rerror=1%, then CMR=34dB
phase margin by making the output load resistive at If using resistors with 1% tolerance and gain=1, the
higher frequencies. The larger the value of RISO, the CMR will only be 34dB.
more stable the output voltage will be. However, larger
values of RISO result in reduced output swing, reduced
output current drive and reduced frequency bandwidth. Current Sensing
Current sensing applications are one such application
V+ in a wide range of electronic applications and mostly
R
used for feedback control systems, including power
ISO metering battery life indicators and chargers, over-
Vin
Vout current protection and supervising circuit, automotive,
and medical equipment. In such applications, it is
C
L desirable to use a shunt with very low resistance to
minimize the series voltage drop and minimizes wasted
power, and allows the measurement of high current.
V- The NJM8530/NJM8532/NJM8534 is ideal for these
Figure4. Isolating capacitive load current sensing applications.
Figure6 shows a high-side current sensing circuit, and
Differential Amplifier Figure7 shows a low-side current sensing circuit. The
Figure5 shows a one op-amp differential amplifier that NJM8530/NJM8532/NJM8534 has rail-to-rail input and
consists of the single op-amp and four external output characteristics, thus allows the both of high-side
resistors. Differential amplifier amplifies the difference and low-side current sensing circuit. Futuremore, low
between its two input pins, and rejects the common- supply current of 290µA/ch can save the power at
mode input voltage at both input pins. This is used in battery applications.
variety of applications including current sensing, The NJM8530/NJM8532/NJM8534 operates up to 14V,
differential to single-end converter, isolation amplifier to and rail-to-rail feature allows the output voltage close to
remove common-mode noise. 14V (almost reach the power supply of op-amp). For
example, if using a typical shunt resistor of 0.1Ω, allows
R2 the current sensing up to approximately 1.4A of current.
The differential amplifier’s common-mode rejection
R1 ratio (CMR) is primarily determined by resistor
V1
Vout mismatches. For details, refer to Differential Amplifiers
V2 in the Applications Information.
R3
R4
Vref
R1+R2 R4 R2 R1+R2 R3
Vout= R3+R4 R1
V2- V1+
R1 R3+R4 R1
Vref
R1=R3, R2=R4
R2
Vout=R1(V2-V1)+ Vref
Ver.03 [ 14]
NJM8530/NJM8532/NJM8534
■ APPLICATIONS INFORMATION
Current Sensing (continues)
14V
Rs I Load
I Rs
14V
14V 14V
1k 1k
Vout Vout
1k 1k
100k 100k
Ver.03 [ 15]
NJM8530/NJM8532/NJM8534
■ PACKAGE DIMENSIONS
2.9±0.2
0°~15°
1.9±0.2
0.2M IN
5 4
+0.2
1.6 - 0.1
2.8±0.2
0.6
1 2 3
0.95±0.1
+0.1
0.6MAX 0.1-0.03
1.1±0.1
Unit: mm
0.1MAX
0.4±0.1
0.1
SOT-23-5Package
5.0±0.3 0 ~ 10º
8 5
6.8±0.3
5.0±0.2
0.5±0.2
1 4
1.27
+0.1
0.74MAX 0.15 - 0.05
1.6±0.15
Unit: mm
0.15±0.1
0.1
0.35±0.1
0.12 M
DMP8 Package
Ver.03 [ 16]
NJM8530/NJM8532/NJM8534
■ PACKAGE DIMENSIONS
+0.3
3.50 - 0.1
0 ~ 10º
8 5
4.4±0.2
6.4±0.3
0.5±0.2
1 4
0.65
+0.1
0.9MAX 1.15±0.1 0.15 -0.05
Unit: mm
0.1±0.1
0.1
0.22±0.1 M
0.1
SSOP8 Package
0~10°
2.9±0.1
8 5
2.8±0.1
4.0±0.2
0.55±0.1
1 4
+0.05
0.65 0.127-0.03
0.475±0.1
1.0MAX
Unit: mm
0.1±0.05
0.08
0.2±0.05
0.05 M
MSOP8 (TVSP8)
meet JEDEC MO-187-DA / thin Package
Ver.03 [ 17]
NJM8530/NJM8532/NJM8534
■ PACKAGE DIMENSIONS
+0.3
5.0 - 0.1
0 ~ 10º
14 8
4.4±0.2
6.4±0.3
0.5±0.2
1 7
0.65
+0.1
0.67MAX 0.15-0.05
1.15±0.1
Unit: mm
0.1±0.1
0.1
0.22±0.1
0.1 M
SSOP14 Package
[CAUTION]
The specifications on this databook are only
given for information, without any guarantee as
regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.
Ver.03 [ 18]