Download as pdf or txt
Download as pdf or txt
You are on page 1of 68

DATE: May 17, 2021

MURRAY CENTENNIAL PUBLIC SCHOOL


JOB NAME

ADAMSON & DOBBIN LTD.


INSTALLING CONTRACTOR

RV ANDERSON ASSOCIATES LTD.


CONSULTING ENGINEER

SUBMITTAL KP
REV.1 05/21/2021
RVA: resubmit the Hot water coil (HW-103,104,
and 106) only, the remaining items in this shop x
drawing should be reviewed as noted.

FOR APPROVALS
REVIEWED
Carrier Canada Adamson & Dobbin Ltd.
195 Statesman Drive May 17th 2021
Mississauga, Ontario R. Stephen Dawson
L5S 1X4

NOTE: EQUIPMENT WILL NOT BE ORDERED UNTIL ENGINEERING APPROVALS


ARE RECEIVED

PREPARED BY: JAIRO DELGADO


PHONE: 416-399-5315
EMAIL: JAIRO.DELGADO@CARRIERENTERPRISE.COM

-1-
Unit Report For RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Unit Parameters Dimensions (m. cm.) & Weight (kg.) ***


Unit Model: ......................... 48TCRD20A2P5-6V3J0 Unit Length: ............................. 3m. 24.8025cm.
Unit Size: ...........................................20 (17.5 Tons) Unit Width:............................... 2m. 20.0275cm.
Volts-Phase-Hertz: ..................................... 208-3-60 Unit Height: ............................. 1m. 25.4125cm.
Heating Type: ..................................................... Gas *** Total Operating Weight: .................... 1129 kg
Duct Cfg: ............ Vertical Supply / Vertical Return
Stainless Steel, Medium Heat *** Weights and Dimensions are approximate. Weight
does not include unit packaging. Approximate
Round Tube Plate Fin Coils dimensions are provided primarily for shipping purposes.
For exact dimensions and weights, refer to appropriate
product data catalog.

Lines and Filters


Gas Line Size: ..................................................... 3/4
Condensate Drain Line Size: .............................. 3/4
Return Air Filter Type: ........................... Throwaway Note: the unit model number shown on this submittal
Return Air Filter Quantity: ....................................... 6 has been selected to conform with the specifications
Return Air Filter Size: ..............................20 x 25 x 2
as listed on Schedule A, Drawing M107 Revision D.
Unit Configuration Refer to the following page for model number break
Medium Static Option - Vertical Models
Ecoat Al/Cu - Al/Cu - Louvered Hail Guards
down details.
Electromechanical Controls w/W7220 Econo Controller
Temp Ultra Low Leak Economizer With Power Exhaust (Vertical Air Flow Only)
Hinged Access Panels
Non-Fused Disconnect RVA: General Contractor to provide
Standard Packaging the necessary fittings to connect the
2-Speed indoor fan motor controlled by VFD Gas pipe to the RTU-101

Warranty Information
1-Year parts(std.)
5-Year compressor parts(std.)
15-Year heat exchanger - Stainless Steel(std.)
Complete Unit Year 2-5 Parts Only Extended Warranty
Start-up by Carrier Representative
Complete Unit 1st Year Carrier CCS Labor Warranty

Ordering Information

Part Number Description Quantity


48TCRD20A2P5-6V3J0 Rooftop Unit 1
Base Unit
Medium Static Option - Vertical Models
Ecoat Al/Cu - Al/Cu - Louvered Hail Guards
Hinged Access Panels
Ultra Low leak Temp Econo X, W7220 control, cent pwr exhaust.
Meets Calf. Title 24 FDD & Leak Rates
2 Speed Fan Controller (VFD) and Non-Fused Disconnect RVA: General Contractor
to coordinate the
Accessories Sensors and switches
CRDISKIT001A00 2 Speed VFD display kit 1
MS7505A2030 Honeywell 2-10VDC Actuator
needed with the Control
Contractor.
Note:
BAS contractor shall supply the required DDC / BACNET Card, SAT/RAT/OAT/CO2 Sensors,
Space Temp Sensor, Enthalpy Sensor, Humidity Sensor, Freeze Stat and Filter Status
Switch.
Packaged Rooftop Builder 1.58
-2- Page 1 of 11
Commercial Products 48TC
Vertical Models
15 TO 27.5 TONS
Carrier Corporation  Syracuse, N.Y. 13221 F.O.B. SHIPPING POINT
SUBJECT TO CHANGE WITHOUT NOTICE FREIGHT AS PER D.O.M.
MODEL NOMENCLATURE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
4 8 T C D D 2 4 A 1 G 6 - 0 A 0 A 0

Packaging & Seismic Compliance


0 = Standard
Unit Heat Type 3 = California seismic complaint
48 – Gas Heat
Packaged Electrical Options
Rooftop A = None
C = Non-Fused Disconnect
G = 2-Speed Indoor Fan (VFD) Controller
Tier/Model J = 2-Speed Fan Controller (VFD) and Non-Fused Disconnect
TC – Standard Efficiency

Service Options
0 = None
Heat Size 1 = Unpowered Convenience Outlet
D - Low Gas heat 2 = Powered Convenience Outlet
E - Medium Gas Heat 3 = Hinged Panels
F - High Gas Heat 4 = Hinged Panels, Unpowered Convenience Outlet
S - Low Stainless Gas Heat 5 = Hinged Panels, Powered Convenience Outlet
R - Medium Stainless Gas Heat
T - High Stainless Gas Heat Intake / Exhaust Options
A = None
Refrigeration Systems Options B = Temperature Economizer w/ Barometric Relief
D - 2 – Stage Cooling F = Enthalpy Economizer w/ Barometric Relief
E – 2 – Stage Cooling with Humidi- K = 2-Position Damper
MiZer (only available on 17- U = Temp Ultra Low Leak Economizer w/Baro Relief
28 sizes with RTPF coil V = Temp Ultra Low Leak Economizer w/PE (cent) Power Exhaust
models) W = Enthalpy Ultra Low Leak Economizer w/Baro Relief
X = Enthalpy Ultra Low Leak Economizer w/PE (cent) Power Exhaust
Cooling Tons (Vertical Air Flow Models Only) D = Temperature Economizer with PE (cent) Power Exhaust
17 - 15 ton
20 - 17.5 ton Base unit controls
24 - 20 ton 0 = Electro-mechanical Controls Can be used with W7212
28 - 25 ton EconoMi$er IV (Non – Fault Detection and Diagnostic)
30 – 27.5 ton 1 = PremierLink Controller
2 = RTU Open Multi-Protocol Controller
6 = Electro-mechanical w/ 2-speed fan and W7220 Econo controller
Controls. Can be used with W7220 EconoMi$er X (with Fault
Sensor Options Detection and Diagnostic)
A = None
B = RA Smoke Detector
C = SA Smoke Detector Design Revision
D = RA + SA Smoke Detector - = Factory Assigned
E = CO2
F = RA Smoke Detector and CO2
Voltage
G = SA Smoke Detector and CO2
1 = 575/3/60
H = RA + SA Smoke Detector and CO2
5 = 208-230/3/60
J = Condensate Overflow Switch (electro mech controls only)
6 = 460/3/60
K = Condensate Overflow Switch and RA Smoke Detectors
L = Condensate Overflow Switch and RA and SA Smoke
Detectors Coil Options
Novation Coils Only (Outdoor-Indoor-Hail Guard)
G = Al/Al - Al/Cu T = Al/Al - Al/Cu, Louvered
Indoor Fan Options (Vertical Air Flow Models Only) H = Al/Al - Cu/Cu U = Al/Al - Cu/Cu, Louvered
1 = Standard Static Option, Vertical J = Al/Al - E-coat Al/Cu V = Al/Al - E-coat Al/Cu, Louvered
2 = Medium Static Option, Vertical K = Al/Al E-coat - Al/Cu W = Al/Al E-coat - Al/Cu, Louvered
3 = High Static Option, Vertical L = Al/Al E-coat - Al/Cu E-coat X = Al/Al E-coat - Al/Cu E-coat, Louvered
B =Medium Static High Efficiency Motor/Vertical
Indoor fan option #2 Supply, Return Air Flow Round Tube Plate Fin (RTPF) (Outdoor-Indoor-Hail Guard)
is the correct option C =High Static, High Efficiency Motor/Vertical Supply, A = Al/Cu – Al/Cu M = Al/Cu – Al/Cu – Louvered
required to meet the Return Air Flow B = Precoat Al/Cu – Al/Cu N = Precoat Al/Cu – Al/Cu – Louvered
specified airflow and C = E-coat Al/Cu – Al/Cu P = E-coat Al/Cu – Al/Cu - Louvered
external static D = E-coat Al/Cu – E-coat Al/Cu Q = E-coast Al/Cu – E-coat Al/Cu –
pressure Not all possible options can be displayed above – see E = Cu/Cu – Al/Cu Louvered
following pages for more details F = Cu/Cu – Cu/Cu R = Cu/Cu – Al/Cu – Louvered
S = Cu/Cu – Cu/Cu – Louvered

-3-
Certified Drawing for RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Packaged Rooftop Builder 1.58


-4- Page 2 of 11
Certified Drawing for RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Packaged Rooftop Builder 1.58


-5- Page 3 of 11
Certified Drawing for RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Packaged Rooftop Builder 1.58


-6- Page 4 of 11
Certified Drawing for RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Packaged Rooftop Builder 1.58


-7- Page 5 of 11
-8-
Performance Summary For RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Part Number:48TCRD20A2P5-6V3J0

ARI EER: ..................................................................................................................................................... 10.80


IEER: ............................................................................................................................................................. 12.7

Base Unit Dimensions


Unit Length: ......................................................................................................................................... 3248.0 mm
Unit Width: .......................................................................................................................................... 2200.3 mm
Unit Height: ......................................................................................................................................... 1254.1 mm
Operating Weight
Base Unit Weight: .................................................................................................................................... 872 kg
Stainless Steel, Medium Heat: ................................................................................................................... 41 kg
Medium Static Option - Vertical Models: ...................................................................................................... 3 kg
Ecoat Al/Cu - Al/Cu - Louvered Hail Guards: ............................................................................................. 27 kg
Temp Ultra Low Leak Economizer w/PE (cent, Vertical Air Flow Only): ................................................... 168 kg
Hinged Access Panels: ................................................................................................................................ 2 kg
2 Speed Fan Controller (VFD) and Non-Fused Disconnect: ...................................................................... 16 kg

Total Operating Weight: ......................................................................................................................... 1129 kg

Unit
Unit Voltage-Phase-Hertz: ............................................................................................................... 208-3-60
Air Discharge:.................................................................................................................................... Vertical
Fan Drive Type:....................................................................................................................................... Belt
Actual Airflow: ........................................................................................................................................ 2358 L/s
Site Altitude: ............................................................................................................................................. 282 m

Cooling Performance
Condenser Entering Air DB: .................................................................................................................... 28.9 C
Evaporator Entering Air DB: .................................................................................................................... 26.8 C
Evaporator Entering Air WB: ................................................................................................................... 19.4 C
Entering Air Enthalpy: ........................................................................................................................... 56.44 kJ/kg
Evaporator Leaving Air DB: ..................................................................................................................... 11.8 C
Evaporator Leaving Air WB: .................................................................................................................... 11.5 C
Evaporator Leaving Air Enthalpy: .......................................................................................................... 33.55 kJ/kg
Gross Cooling Capacity: ....................................................................................................................... 62.69 kW
Gross Sensible Capacity: ...................................................................................................................... 41.20 kW
Compressor Power Input: ..................................................................................................................... 14.24 kW
Coil Bypass Factor: ............................................................................................................................... 0.081

Mixed Air
Outdoor Air Airflow: ................................................................................................................................ 1369 L/s
Outdoor Air DB: ....................................................................................................................................... 28.9 C
Outdoor Air WB: ...................................................................................................................................... 20.6 C
Outdoor Air Htg. Temp.: ......................................................................................................................... -27.2 C
Return Air DB: ......................................................................................................................................... 23.9 C
Return Air WB: ........................................................................................................................................ 17.8 C
Return Air Htg. Temp.: ............................................................................................................................ 21.1 C

Heating Performance
Heating Airflow: ...................................................................................................................................... 2358 L/s
Entering Air Temp: .................................................................................................................................... 1.7 C
Leaving Air Temp: ................................................................................................................................... 28.4 C
Gas Heating Input Capacity: ......................................................................................................... 72.7 / 90.9 kW
Gas Heating Output Capacity: ...................................................................................................... 58.6 / 73.6 kW
Temperature Rise: .................................................................................................................................. 26.7 K
Thermal Efficiency (%): ........................................................................................................................... 81.0

Supply Fan
External Static Pressure:..................................................................................................................... 250.00 Pa

Packaged Rooftop Builder 1.58


-9- Page 6 of 11
Performance Summary For RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Options / Accessories Static Pressure


Economizer: .................................................................................................................................... 12.92 Pa
Power Exhaust:.............................................................................................. (Fan Data Includes Drop)
Total Application Static (ESP + Unit Opts/Acc.): ................................................................................. 262.92 Pa
Fan RPM: ................................................................................................................................................. 837
Fan Power: .............................................................................................................................................. 1.94 kW
NOTE: ................................................................................................ Selected IFM RPM Range: 713 - 879
NOTE:At the selected supply CFM value, a saturated suction temperature of less than 32 F (0 C) is possible if
running less than 62 F (16.7 C) ambient. This implies a slight risk of freezing the evaporator coil during
operation. To avoid this slight risk, it is suggested to re-program the VFD 'low fan speed' to at least
3500 cfm using the accessory VFD display kit. ...............................................................................................

Power Exhaust
Return Duct Static: .............................................................................................................................. 102.82 Pa
Max. Air to Exhaust: ............................................................................................................................... 2002 L/s

Electrical Data
Voltage Range: ............................................................................................................................... 187 - 253
Compressor #1 RLA:............................................................................................................................... 29.5
Compressor #1 LRA:................................................................................................................................ 195
Compressor #2 RLA:............................................................................................................................... 28.2
Compressor #2 LRA:................................................................................................................................ 239
Indoor Fan Motor Type: .......................................................................................................................... MED
Indoor Fan Motor FLA: ............................................................................................................................ 13.6
Combustion Fan Motor FLA (ea): ............................................................................................................ 0.52
Power Supply MCA: ................................................................................................................................... 95
Power Supply MOCP (Fuse or HACR):.................................................................................................... 110
Disconnect Size FLA: ............................................................................................................................... 101
Disconnect Size LRA: .............................................................................................................................. 551
Electrical Convenience Outlet: .............................................................................................................. None
Power Exhaust [Motor Qty / FLA(ea motor)]: ....................................................................................... 2 / 5.9
Outdoor Fan [Qty / FLA (ea)]: .............................................................................................................. 3 / 1.5

Control Panel SCCR: 5kA RMS at Rated Symmetrical Voltage

Acoustics
Sound Rating: ......................................................................................................................................... 84.0 db
Sound Power Levels, db re 10E-12 Watts

Discharge Inlet Outdoor


63 Hz 88.0 87.4 92.2
125 Hz 82.0 74.8 83.9
250 Hz 73.9 68.9 80.4
500 Hz 72.6 61.5 81.8
1000 Hz 66.8 55.6 78.7
2000 Hz 65.5 50.1 76.5
4000 Hz 66.2 46.0 72.2
8000 Hz 55.9 36.4 65.4

A-Weighted 75.1 66.4 84.1

Advanced Acoustics

Packaged Rooftop Builder 1.58


-10- Page 7 of 11
Performance Summary For RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Advanced Accoustics Parameters


1. Unit height above ground: .................................... 9.1 m
2. Horizontal distance from unit to receiver: ........... 15.2 m
3. Receiver height above ground: ............................ 1.7 m
4. Height of obstruction: ........................................... 0.0 m
5. Horizontal distance from obstruction to receiver: . 0.0 m
6. Horizontal distance from unit to obstruction: ........ 0.0 m

Detailed Acoustics Information

Octave Band Center Freq. Hz 63 125 250 500 1k 2k 4k 8k Overall


A 92.2 83.9 80.4 81.8 78.7 76.5 72.2 65.4 93.6 Lw
B 66.0 67.8 71.8 78.6 78.7 77.7 73.2 64.3 84.1 LwA
C 59.8 51.5 48.0 49.4 46.3 44.1 39.8 33.0 61.2 Lp
D 33.6 35.4 39.4 46.2 46.3 45.3 40.8 31.9 51.7 LpA

Legend
A Sound Power Levels at Unit's Acoustic Center, Lw
B A-Weighted Sound Power Levels at Unit's Acoustic Center, LwA
C Sound Pressure Levels at Specific Distance from Unit, Lp
D A-Weighted Sound Pressure Levels at Specific Distance from Unit, LpA

Calculation methods used in this program are patterned after the ASHRAE Guide; other ASHRAE Publications and the AHRI Acoustical
Standards. While a very significant effort has been made to insure the technical accuracy of this program, it is assumed that the user
is knowledgeable in the art of system sound estimation and is aware of the tolerances involved in real world acoustical estimation.
This program makes certain assumptions as to the dominant sound sources and sound paths which may not always be appropriate to
the real system being estimated. Because of this, no assurances can be offered that this software will always generate an accurate
sound prediction from user supplied input data. If in doubt about the estimation of expected sound levels in a space, an Acoustical
Engineer or a person with sound prediction expertise should be consulted.

Packaged Rooftop Builder 1.58


-11- Page 8 of 11
Performance Summary For RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

( h Pa ) F a n Cu r v e
5 . 0
1 2 0 0 R P M
1 1 0 0 R P M
Pr e s s u r e

1 0 0 0 R P M
3 . 8

9 0 0 R P M

R P
S C 5 . 5 9 k W
2 . 5 8 0 0 R P M
S t a t ic

7 0 0 R P M

6 0 0 R P M

1 . 3 3 . 7 3 k W
5 0 0 R P M
2 . 2 4 k W
4 0 0 R P M 1 . 4 9 k W
1 . 1 2 k W
3 0 0 R P M 0 . 7 5 k W
0 . 3 7 k W
0 . 5 6 k W

0 . 0
0 . 0 5 . 0 1 0 . 0 1 5 . 0 2 0 . 0 2 5 . 0 3 0 . 0 3 5 . 0 4 0 . 0 4 5 . 0
A ir f lo w ( l/ s - h u n d r e d s )
= 8 3 7 k W = 1 . 9 4 M a x i m u m R P M = 1 2 9 0 M a x i m u m k W = 6
S C - S y s t e m C u r v e R P - R a t e d P o i n t

Packaged Rooftop Builder 1.58


-12- Page 9 of 11
RVA: General Contractor to
Table 8 – PHYSICAL DATA (HEATING) coordinate the
15 −PRV rating on
27.5 TONS
48TC**17 48TC**20 48TC**24 the Natural Gas
48TC**28 pipe and
48TC**30
Gas Connection make sure it suited for the
# of Gas Valves 1 1 1 range1 of the equipment.
1
Natural gas supply line pressure 5 -13 / 5 -13 / 5 -13 / 5 -13 / 5 -13 /
(in. w.g.) / (PSIG) 0.18-0.47 0.18-0.47 0.18-0.47 0.18-0.47 0.18-0.47
LP supply line pressure 11-13 / 11-13 / 11-13 / 11-13 / 11-13 /
(in. w.g). / (PSIG) 0.40-0.47 0.40-0.47 0.40-0.47 0.40-0.47 0.40-0.47
Heat Anticipator setting (Amps)
1st stage 0.14 0.14 0.14 0.14 0.14
2nd stage 0.14 0.14 0.14 0.14 0.14
Natural Gas Heat
# of stages / # of burners (total) 2/5 2/5 2/5 2/5 2/5
Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
LOW
Rollout switch opens / closes (F) 195 / 115 195 / 115 195 / 115 195 / 115 195 / 115
Temperature Rise (F) 25 - 55 25 - 55 25 - 55 25 - 55 25 - 55

# of stages / # of burners (total) 2/7 2/7 2/7 2/7 2/7


Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
MED
Rollout switch opens / closes (F) 195 / 115 195 / 115 195 / 115 195 / 115 195 / 115
Temperature Rise (F) 30- 60 30- 60 30- 60 30- 60 30- 60

# of stages / # of burners (total) 2 / 10 2 / 10 2 / 10 2 / 10 2 / 10


Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
HIGH
Rollout switch opens / closes (F) 195 / 115 195 / 115 195 / 115 195 / 115 195 / 115
Temperature Rise (F) 35-65 35-65 35-65 35-65 35-65

Liquid Propane Heat


# of stages / # of burners (total) 2/5 2/5 2/5 2/5 2/5
Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
LOW
Rollout switch opens / closes (F) 195 / 115 195 / 115 195 / 115 195 / 115 195 / 115
Temperature Rise (F) 25 - 55 25 - 55 25 - 55 25 - 55 25 - 55

# of stages / # of burners (total) 2/7 2/7 2/7 2/7 2/7


Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
MED
Rollout switch opens / closes (F) 195 / 115 196 / 115 197 / 115 198 / 115 199 / 115
Temperature Rise (F) 30- 60 30- 60 30- 60 30- 60 30- 60

# of stages / # of burners (total) 2 / 10 2 / 10 2 / 10 2 / 10 2 / 10


Connection Size 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT 3/4" NPT
HIGH
Rollout switch opens / closes (F) 195 / 115 195 / 115 195 / 115 195 / 115 195 / 115
Temperature Rise (F) 35- 65 35- 65 35- 65 35- 65 35- 65

-13- 16
-14-
Fig. 56 — 48TC**17-30 Control Wiring Diagram

51
-15-
Fig. 57 — 48TC**17-30 Power Wiring Diagram, 208/230-3-60

52
Unit Feature Sheet for RTU-101
Project: Murray Centennial PS 05/14/2021
Prepared By: Doug Roberts P. Eng. 05:06PM

Packaged Rooftop Builder 1.58


-16- Page 10 of 11
HONEYWELL SPRING RETURN
DIRECT COUPLED
0-10VDC ACTUATOR

PART #MS7505A2030

-17-
N314 3 Nm, 5 Nm Series Spring Return
Direct Coupled Actuators
MS3103, MS3105, MS4103, MS4105, MS7403,
MS7405, MS7503, MS7505, MS8103, MS8105
MS3103, MS3105, MS4103, MS4105, MS7403, MS7405, SPECIFICATION DATA
MS7503, MS7505, MS8103, MS8105 Spring Return Direct
Coupled Actuators (DCA) are used within heating, ventilating,
and air-conditioning (HVAC) systems. They can drive a variety SPECIFICATIONS
of quarter-turn, final control elements requiring spring return
fail-safe operation. Models:
 See Table 1.
Device Weight:
APPLICATIONS  3.5 lbs (1.60 kg)
Ambient Operating Temperature:
• Volume control dampers, mounted directly to the drive  -40° to 150°F (-40° to 65°C)
shaft or remotely (with the use of accessory hardware).
 -22° to 150°F (-30° to 65°C) (Two position only)
• Quarter-turn rotary valves, such as ball or butterfly
valves mounted directly to the drive shaft. Shipping and Storage Temperature:
• Linear stroke globe or cage valves mounted with  -40° to +150°F (-40° to +65°C)
linkages to provide linear actuation. Humidity Ratings:
• Available with cable on select models.  5% to 95% R.H., Non-Condensing

Table 1. Models.

Model Number Power Supply Time


(including 3 ft. SPDT Aux
Model Number whip) Torque Voltage VA Driving1 Drive (sec) Control Input/Output Description Switch
MS3103J1030 Sylk-enabled 0
MS7403A2030 Floating, Modulating2 , Three-Position, 0
90 Feedback
24 Vac/dc @50/60
MS7503A2030 Hz +/-20% 6/3 0
27 lb-in 24Vdc+/-10% Floating, Modulating3, and Feedback
MS7503A2130 1
(3 Nm)
MS8103A1030 0
45 Two-Position (SPST)
MS8103A1130 1
MS4103A1030 100-250 Vac 0
6/9 45 Two-Position (SPST)
MS4103A1130 @50/60Hz 1
MS3105J3030 Sylk-enabled (5 addresses & Analog 0
MS3105J3130 Output) 1
MS7405A2030 Floating, Modulating2, Three-Position, 0
24 Vac/dc @50/60 90
Feedback
Hz +/-20% 6/3
MS7505A2030 MS7505W2030 44 lb-in 24Vdc+/-10% 0
Floating, Modulating3, and Feedback
MS7505A2130 MS7505W2130 (5 Nm) 1
MS8105A1030 MS8105W1030 0
45 Two-Position (SPST)
MS8105A1130 MS8105W1130 1
MS4105A1030 100-250 Vac 0
6/9 45 Two-Position (SPST)
MS4105A1130 @50/60Hz 1
1 Number represents range
2 2-10 Vdc
3 0/2-10 Vdc

By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising
out of your use or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and
subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees, arising out of, or

-18-
resulting from, any modification to the literature by you. Put Bar Code Here
63-1336-05
3 NM, 5 NM SERIES SPRING RETURN DIRECT COUPLED ACTUATORS
Electrical Connections: Stroke: 95° ±3°, mechanically limited.
 Field wiring 18 AWG (0.5 mm) to 14 AWG (1.5 mm)
Approvals:
conductors (stranded or solid) and up to 2 - 14 AWG (1.5
 UL873
mm) conductors (stranded) to screw terminals, located
 IEC 60730-1 and Part 2–14
under the removable access cover.
 UL1097 for Double Insulation
Auxiliary Switch (One SPDT):  CE Certification Low Voltage Directive 2006/95/EC
 Switch adjustable from 0-95°  CE EMC 2004/108/EC
 500 uA Resistive at 5 Vdc (minimum)  C-Tick N314
 250 Vac, 8 A resistive, 3 A inductive
Design Life (at Rated Voltage):
Mounting: Self-centering shaft adapter (shaft coupling):  60,000 full stroke cycles; 1,500,000 repositions;
 Round damper shafts: 3/8 to 5/8 in. (9 to 16 mm) 60,000 full stroke spring returns.
 Square damper shafts: 1/4 to 1/2 in. (6 to 13 mm)
Enclosure Ratings:
Minimum Damper Shaft Length:  IP54
 1 in. (25 mm); 3 in.(76 mm) recommended.  NEMA 2
 Flame Resistance UL94-5VA
Torque Ratings:
Typical Holding, Driving, Spring Return: Input Impedance:
 MSXX03: 27 lb-in. (3 Nm)  95 kOhms minimum.
 MSXX05: 44 lb-in. (5 Nm)
Feedback Signal:
Stall Maximum (fully open at 75°F):
 0(2)-10 Vdc, 3 mA minimum.
 MSXX03: 71 lb-in. (8 Nm)
 MSXX05: 106 lb-in. (12 Nm) Analog Output Signal:
 0(2)-10Vdc
Spring Return Timing (at rated load):
 < 25 seconds @ -4°F to 130°F (-20°C to 55°C) Noise Rating at 1m (Maximum):
< 60 seconds @ -22°F (-30°C)  Driving
 Floating/Modulating/Econ/Sylk-enabled: < 40 dB(A)
Cable Specification:  2-Position: < 50 dB(A)
 300 V, 75° C, Plenum Rated, 3 ft length from end of access  Spring Return: < 60 dB(A)
cover, 18 AWG
Accessories:
Sylk™ Bus  27518 Balljoint (5/16 in.)
 Sylk is a two-wire, polarity insensitive bus that provides  103598 Balljoint (1/4 in.)
communications between a Sylk-enabled Zelix and a Sylk-  27520B, C, E, G, H, K, L, Q Pushrod (5/16 in. diameter)
enabled controller. For wiring, the Zelix Sylk-enabled  STRN-STRNRLF Water-tight Cable Gland/Strain-relief
actuator may be mounted up to 200 ft. (61 m) from the Fitting (10 pack)
controller; twisted pair wire is recommended for wire runs  STRN-WMK-01 Wall Mount Kit
longer than 100 ft. (30.5 m). Using Sylk-enabled actuators  STRN-ECONO-01 Economizer Retrofit Kit
saves I/O on the controller and is faster and cheaper to  STRN-CRK-01 Crank Arm Kit
install since the bus is polarity insensitive.  STRN-SCSA Self Centering Shaft Adapter
 STRN-CA-01 Crank Arm (Non-Self-Centering)
3-55/64 (98) 3-5/32 (80)
1-9/16 1-15/16
2-27/64 (61) 47/64  STRN-CA-02 Crank Arm (Self-Centering)
(40) (49) (19)  STRN-BRKT Anti-Rotation Bracket
1-1/8
(29)
TYPICAL SPECIFICATION
Spring return actuators shall be direct coupled type requiring neither cran-
1-1/16
(27) karm nor linkage and be capable of direct mounting to a jackshaft of up to 5/8
in. diameter. The actuator shall connect to the shaft using a removable output
hub with a self-centering shaft coupling. This coupling shall provide concen-
tric mounting and include an integral adjustable range-stop mechanism.
4-9/16
(116) 6-61/64 The actuator shall provide two-position, floating, proportional, or Sylk bus
(177) control. Proportional control refers to direct acceptance of 0-10 Vdc, 2-10 Vdc,
or (with addition of a 500 ohm resistor) a 4-20 mA input signal. Proportional
5-27/32
(148) and floating control models shall provide a feedback signal. Sylk-enabled
models provide control and feedback via communication between the actua-
tor and Sylk-enabled controller. Actuators shall provide wiring terminals
located within an integral access cover with conduit connections. Propor-
tional and floating actuators shall have a rotation direction control switch
accessible on the cover.
All spring return actuators must be designed for either clockwise or counter-
clockwise fail-safe operation with a continuously engaged mechanical spring.
This spring must return the valve or actuator to a fail-safe position within 25
2-1/64 seconds of power loss.
(55)
All actuators shall be designed for a minimum of 60,000 fullstroke cycles at
rated torque and temperature, 60,000 springreturn cycles and 1,500,000 repo-
1 CABLE AND STRAIN
sitions. Run time shall be constant and independent of: load, temperature,
RELIEF ON SELECT
1 and supply voltage (within specifications). All actuators shall be UL60730 and
MODELS ONLY. 36 (914) M28945A cUL (CSA22.2) listed, have a five year warranty, and be manufactured under
ISO 9001 International Quality Control Standards. Actuators shall be as manu-
factured by Honeywell.
Fig. 1. Dimensional drawing of actuator in in. (mm)

Automation and Control Solutions

-19-
Honeywell International Inc.
1985 Douglas Drive North
® U.S. Registered Trademark
Golden Valley, MN 55422 © 2015 Honeywell International Inc.
63-1336—05 M.S. Rev. 03-15
customer.honeywell.com Printed in United States
37KN
BYPASS AIR TERMINAL
WITHOUT CONTROLLER

RVA:
General Contractor to provide all the duct fitting necessary to connect all the
By pass damper with the duct works as specified in the contract document

UNIT TAG: BPB-101,103,104,105,106


QTY (5)
MODEL: 35KN00—12

UNIT TAG: BPB-102


QTY (1)
MODEL: 35KN00--14

Accessories Included:
22
- Belimo 2-10VDC actuator, 24 VAC
- 115V to 24V transformer

Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

-20-
Unit Report For BPB-101
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-101
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082507030000

Dimensions
Unit Depth: ...................................................................................................................................................................... 835.7 mm
Unit Width: ...................................................................................................................................................................... 660.4 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--12-000000000CS0 35K Bypass Units 1
000000000.00000008250703
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-21- Page 1 of 24
Certified Drawing for BPB-101
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-22- Page 2 of 24
Performance Summary For BPB-101
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-101
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082507030000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 389.4 L/s
Min. Primary Airflow: ....................................................................................................................................................... 331.8 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................389.4 L/s Primary Airflow: ............................................389.4 L/s
Safety Factor: .....................................................60 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 44 35 31 28 22 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 27 17 11 < 10 < 10 < 10 3
Discharge Sound
Primary Sound (Pwl) 39 35 31 30 26 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-23- Page 3 of 24
Acoustics Summary For BPB-101
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-101
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082507030000

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................389.4 L/s Primary Airflow: ............................................389.4 L/s
Safety Factor: .....................................................60 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 44 35 31 28 22 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 27 17 11 < 10 < 10 < 10 3
Discharge Sound
Primary Sound (Pwl) 39 35 31 30 26 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-24- Page 4 of 24
Unit Report For BPB-102
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-102
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................14 Inch (MAX 2500 CFM)
Part Number: ........................................................................ 35KN00--14-000000000CS0000000000.000000096806230000

Dimensions
Unit Depth: ...................................................................................................................................................................... 886.5 mm
Unit Width: ...................................................................................................................................................................... 688.3 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--14-000000000CS0 35K Bypass Units 1
000000000.00000009680623
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-25- Page 5 of 24
Certified Drawing for BPB-102
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-26- Page 6 of 24
Performance Summary For BPB-102
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-102
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................14 Inch (MAX 2500 CFM)
Part Number: ........................................................................ 35KN00--14-000000000CS0000000000.000000096806230000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 456.8 L/s
Min. Primary Airflow: ....................................................................................................................................................... 294.0 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ....................................... 1,323.3 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................456.8 L/s Primary Airflow: ............................................456.8 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: .............................. 34.9 x 27.1 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 46 36 33 29 24 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 29 18 13 < 10 < 10 < 10 6
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 23 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-27- Page 7 of 24
Acoustics Summary For BPB-102
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-102
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................14 Inch (MAX 2500 CFM)
Part Number: ........................................................................ 35KN00--14-000000000CS0000000000.000000096806230000

Other Information: Acoustic Summary:


Maximum Airflow: ....................................... 1,323.3 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................456.8 L/s Primary Airflow: ............................................456.8 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: .............................. 34.9 x 27.1 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 46 36 33 29 24 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 29 18 13 < 10 < 10 < 10 6
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 23 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-28- Page 8 of 24
Unit Report For BPB-103
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-103
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082505150000

Dimensions
Unit Depth: ...................................................................................................................................................................... 835.7 mm
Unit Width: ...................................................................................................................................................................... 660.4 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--12-000000000CS0 35K Bypass Units 1
000000000.00000008250515
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-29- Page 9 of 24
Certified Drawing for BPB-103
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-30- Page 10 of 24
Performance Summary For BPB-103
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-103
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082505150000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 389.4 L/s
Min. Primary Airflow: ....................................................................................................................................................... 243.1 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................389.4 L/s Primary Airflow: ............................................389.4 L/s
Safety Factor: .....................................................60 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 44 35 31 28 22 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 27 17 11 < 10 < 10 < 10 3
Discharge Sound
Primary Sound (Pwl) 39 35 31 30 26 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-31- Page 11 of 24
Acoustics Summary For BPB-103
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-103
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000082505150000

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................389.4 L/s Primary Airflow: ............................................389.4 L/s
Safety Factor: .....................................................60 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 44 35 31 28 22 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 27 17 11 < 10 < 10 < 10 3
Discharge Sound
Primary Sound (Pwl) 39 35 31 30 26 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-32- Page 12 of 24
Unit Report For BPB-104
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-104
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000071205170000

Dimensions
Unit Depth: ...................................................................................................................................................................... 835.7 mm
Unit Width: ...................................................................................................................................................................... 660.4 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--12-000000000CS0 35K Bypass Units 1
000000000.00000007120517
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-33- Page 13 of 24
Certified Drawing for BPB-104
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-34- Page 14 of 24
Performance Summary For BPB-104
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-104
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000071205170000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 336.0 L/s
Min. Primary Airflow: ....................................................................................................................................................... 244.0 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................336.0 L/s Primary Airflow: ............................................336.0 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 38 29 25 22 < 20 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 21 11 < 10 < 10 < 10 < 10 0
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 22 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-35- Page 15 of 24
Acoustics Summary For BPB-104
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-104
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000071205170000

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................336.0 L/s Primary Airflow: ............................................336.0 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 38 29 25 22 < 20 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 21 11 < 10 < 10 < 10 < 10 0
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 22 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-36- Page 16 of 24
Unit Report For BPB-105
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-105
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000086905530000

Dimensions
Unit Depth: ...................................................................................................................................................................... 835.7 mm
Unit Width: ...................................................................................................................................................................... 660.4 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--12-000000000CS0 35K Bypass Units 1
000000000.00000008690553
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-37- Page 17 of 24
Certified Drawing for BPB-105
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-38- Page 18 of 24
Performance Summary For BPB-105
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-105
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000086905530000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 410.0 L/s
Min. Primary Airflow: ....................................................................................................................................................... 261.0 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................410.0 L/s Primary Airflow: ............................................410.0 L/s
Safety Factor: .....................................................58 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 46 37 33 30 24 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 29 19 13 < 10 < 10 < 10 6
Discharge Sound
Primary Sound (Pwl) 41 36 32 31 27 22 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 12 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-39- Page 19 of 24
Acoustics Summary For BPB-105
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-105
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000086905530000

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................410.0 L/s Primary Airflow: ............................................410.0 L/s
Safety Factor: .....................................................58 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 46 37 33 30 24 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 29 19 13 < 10 < 10 < 10 6
Discharge Sound
Primary Sound (Pwl) 41 36 32 31 27 22 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) 12 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-40- Page 20 of 24
Unit Report For BPB-106
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-106
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000072305150000

Dimensions
Unit Depth: ...................................................................................................................................................................... 835.7 mm
Unit Width: ...................................................................................................................................................................... 660.4 mm
Unit Height: ..................................................................................................................................................................... 434.3 mm
Unit Operating Weight : ........................................................................................................................................................ 12 kg
*** Weights and Dimensions are approximate. Weight does not include curbs
and accessories. Approximate dimensions are provided primarily for
shipping purposes. For exact dimensions, refer to certified drawings.

Warranty Information
1 Year Parts Only Warranty

Ordering Information

Part Number Description Quantity


Base Unit
35KN00--12-000000000CS0 35K Bypass Units 1
000000000.00000007230515
0000

Base Unit
0000: Field supplied controls w/ no Control Enclosure and no Flow
Probe
Hangers
Balancing Air Damper, Manual Inlet
Accessories None

Note:
Controls contractor shall supply all DDC / BACNET controllers, SAT sensor, hot water coil
control valve, and space temperature sensor

Air Terminals Builder 2.10a


-41- Page 21 of 24
Certified Drawing for BPB-106
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

CODE
THIS DOCUMENT IS THE PROPERTY OF SUBMISSION OF THESE
CARRIER CORPORATIONAND IS DELIVERED DRAWINGS OR DOCUMENTS BYPASS TERMINAL
CATALOG #
UPON THE EXPRESS CONDITION THAT
THE CONTENTS WILL NOT BE DISCLOSED
OR USED WITHOUT CARRIER
DOES NOT CONSTITUTE
PART PERFORMANCE
OR ACCEPTANCE OF
UNIT WITH 35K
CORPORATION'S WRITTEN CONSENT CONTRACT ELECTRONIC CONTROLS

35K BYPASS TERMINAL UNIT - WITH ELECTRONIC CONTROLS

ACCESSORIES
. Hanger Brackets
. Damper, Manual Inlet
. Damper, Manual Bypass
. Thermostat

NOTES:
1. 20 ga. Steel construction.
2. "D" dimensin is diameter of inlet, bypass and outlet connection.
3. 1/2" dual density coated insulation meeting NFPA90Aand UL 181.
4. Damper operates on a 24 Volt thermostat signal.

INLET SIZE A B C D E F G
6 12-7/8 7-1/8 11-1/8 5-7/8 4-1/4 12-3/8 5-9/16
8 12-7/8 7-1/8 11-1/8 7-7/8 5-1/4 12-3/8 5-9/16
10 14-7/8 8-1/8 13-1/8 9-7/8 6-1/4 14-3/8 6-9/16
12 18-7/8 10-1/8 17-1/8 11-7/8 7-1/4 18-3/8 8-9/16
14 18-7/8 10-1/8 17-1/8 13-7/8 8-1/4 18-3/8 8-9/16
16 22-7/8 12-1/8 21-1/8 15-7/8 9-1/4 22-3/8 10-9/16
18 22-7/8 12-1/8 21-1/8 17-7/8 10-1/4 22-3/8 10-9/16

PRODUCT INFORMATION IS SUBJECT TO CHANGE WITHOUT NOTICE. 3/21/2002


JOB NAME JOB NUMBER LOCATION PAGE NUMBER DRAWING NUMBER

BUYER BUYER # SHEET 1 OF 1 35K-202-1

Air Terminals Builder 2.10a


-42- Page 22 of 24
Performance Summary For BPB-106
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-106
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000072305150000

Unit Performance
Altitude: .................................................................................................................................................................................. 0 m
Max. Primary Airflow: ...................................................................................................................................................... 341.0 L/s
Min. Primary Airflow: ....................................................................................................................................................... 243.1 L/s
Inlet Static Pressure: ....................................................................................................................................................... 0.149 kPa
Downstream Static Pressure: .......................................................................................................................................... 0.050 kPa
Minimum Static Pressure Drop:....................................................................................................................................... 0.001 kPa
Note: ...................................................................................... Inlet Static Pressure includes downstream pressure drop.

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................341.0 L/s Primary Airflow: ............................................341.0 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 39 30 26 23 < 20 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 22 12 < 10 < 10 < 10 < 10 0
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 22 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-43- Page 23 of 24
Acoustics Summary For BPB-106
Project: Murray Centennial PS 04/07/2021
Prepared By: Doug Roberts P. Eng. 04:24PM

Unit Parameters
Tag Name: ................................................................................................................................................................ BPB-106
Quantity: ................................................................................................................................................................................. 1
Model Type: .......................................................................................................................... No Controls or Field Supplied
Model: ........................................................................................................................................................35K Bypass Units
Control Type: ................................................................................0000: Field supplied controls w/ no Control Enclosure
Unit and Inlet Size: ..........................................................................................................................12 Inch (MAX 2000 CFM)
Part Number: ........................................................................ 35KN00--12-000000000CS0000000000.000000072305150000

Other Information: Acoustic Summary:


Maximum Airflow: ..........................................972.2 L/s Sound Power Levels, dB re 10E-12 watts
Design Airflow: ..............................................341.0 L/s Primary Airflow: ............................................341.0 L/s
Safety Factor: .....................................................65 %
Unit LxWxH: ................................. 32.9 x 26 x 17.1

Octave Bands (dB)


Radiated Sound 2 3 4 5 6 7 NC
Primary Sound (Pwl) 39 30 26 23 < 20 < 20 *
Total Attenuation 17 18 20 23 25 26 *
Room Sound Level (Spl) 22 12 < 10 < 10 < 10 < 10 0
Discharge Sound
Primary Sound (Pwl) 35 31 27 26 22 < 20 *
Total Attenuation 29 30 41 53 55 41 *
Room Sound Level (Spl) < 10 < 10 < 10 < 10 < 10 < 10 0

Notes:
1. Room NC level shown includes attenuation transfer functions obtained from tests in AHRI Standard 885.
2. Sound data obtained from test conducted in accordante with AHRI Standard 880-11 and corrected for end reflection.

The results of this program are only an aid to the designer, and are not a substitute for professional services.
Carrier Corporation accepts no liability for the adequacy of any resulting design or installation.
All data subject to change without notice.

Air Terminals Builder 2.10a


-44- Page 24 of 24
NMX24-MFT Technical Data Sheet
Modulating, Non-Spring Return, 24 V, Multi-Function Technology®

Torque min. 90 in-lb, for control of damper surfaces up to 22 sq. ft.

Application
For proportional modulation of dampers in HVAC systems. Actuator sizing
should be done in accordance with the damper manufacturer’s specifications.

The actuator is mounted directly to a damper shaft up to 1.05” in diameter by


means of its universal clamp. A crank arm and several mounting brackets are
available for applications where the actuator cannot be direct coupled to the
damper shaft.

The default parameters for 2 to 10 VDC applications of the …MFT actuator are
assigned during manufacturing. If necessary, custom versions of the actuators
can be ordered. The parameters can be changed by two means: pre-set and
Technical Data 1512
custom configurations from Belimo or on-site configurations using the Belimo
Power Supply 24 VAC, ±20%, 50/60 Hz, 24 VDC, ±10% PC-Tool software.
Power consumption in operation 3.5 W
Power consumption in rest 1.3 W Operation
position The actuator is not provided with and does not require any limit switches, but is
Transformer sizing 6 VA (class 2 power source) electronically protected against overload. The anti-rotation strap supplied with
Shaft Diameter 1/2...1.05” round, centers on 1/2” and 3/4” the actuator will prevent lateral movement.
with insert, 1.05” without insert
The NMB(X) series provides 95° of rotation and a visual indicator indicates
Electrical Connection 18 GA plenum cable with 1/2” conduit
position of the actuator. When reaching the damper or actuator end position,
connector, degree of protection NEMA 2 /
the actuator automatically stops. The gears can be manually disengaged with a
IP54, 3 ft [1 m] 10 ft [3 m] and 16ft [5 m]
button on the actuator cover.
Overload Protection electronic throughout 0...95° rotation
Operating Range 2...10 V (default), 4...20 mA w/ ZG-R01 (500 The NMB(X)24-MFT actuators use a brushless DC motor, which is controlled
Ω, 1/4 W resistor), variable (VDC, PWM, on/ by an Application Specific Integrated Circuit (ASIC). The ASIC monitors
off, floating point) and controls the actuator’s rotation and provides a digital rotation sensing
Operating range Y variable Start point 0.5...30 V (DRS) function to prevent damage to the actuator in a stall condition. Power
End point 2.5...32 V consumption is reduced in holding mode.
Input Impedance 100 kΩ for 2...10 V (0.1 mA), 500 Ω for
4...20 mA, 1500 Ω for PWM, On/Off and Add-on auxiliary switches or feedback potentiometers are easily fastened
Floating point directly onto the actuator body for signaling and switching functions.
Date created, 02/10/2020 - Subject to change. © Belimo Aircontrols (USA), Inc.

Position Feedback 2...10 V, Max. 0.5 mA, VDC variable


Angle of rotation Max. 95°, adjustable with mechanical stop
Torque motor 90 in-lb [10 Nm]
Dimensions (Inches[mm])
Direction of motion motor selectable with switch 0/1
Position indication Mechanically, 30...65 mm stroke 1/2” to 1.05” [12.7 to 26.67]
Manual override external push button 2/5” to 1.05” [10 to 26.67]
Running Time (Motor) default 150 s, variable 45...170 s
Ambient humidity max. 95% r.H., non-condensing
2.42" [61.4]

Ambient temperature -22...122°F [-30...50°C]


Storage temperature -40...176°F [-40...80°C]
Degree of Protection IP54, NEMA 2, UL Enclosure Type 2
Housing material UL94-5VA
3.66" [93]
Agency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSA
E60730-1:02, CE acc. to 2014/30/EU and
2014/35/EU 2" [50.8]
0.98" [25] 4.74" [120.4]
Noise level, motor 45 dB(A)
Servicing maintenance-free
Quality Standard ISO 9001
Weight 1.2 lb [0.54 kg]
3.15" [80]

†Rated Impulse Voltage 800V, Type action 1, Control Pollution Degree 3.

7.7" [196.2]

800-543-9038 USA -45-


866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
NMX24-MFT Technical Data Sheet
Modulating, Non-Spring Return, 24 V, Multi-Function Technology®

Accessories
K-NA Shaft clamp reversible
24 VAC Transformer 1 3 11
ZG-100 Univ. right angle bracket 17”x11-1/8”x6” (HxWxbase).
ZG-101 Univ. right angle bracket 13x11x7-7/16” (HxWxbase).
Line Blk (1) Common
ZG-103 Univ. right angle bracket 7-1/2x11x2-3/4” (HxWxbase).
Volts Red (2) Hot +
ZG-104 Univ. right angle bracket 13-5/8x7-1/2x4” (HxWxbase).
ZG-NMA Mounting kit for linkage operation
AV8-25 Shaft extension Wht (3) Y Input
1
ZG-NMSA-1 Shaft extension for 1/2” diameter shafts (3.8” L). Position (–) Pnk (4) Y Input
2
ZS-100 Weather shield - galvaneal 13x8x6” (LxWxD). Feedback VDC (+) Org (5) U Output
ZS-150 Weather shield - PC w/ foam seal 16x8-3/8x4” (LxWxD).
TOOL-06 8 mm and 10 mm wrench. On/Off
S1A Auxiliary switch for damper actuators and rotary actuators
S2A Auxiliary switch for damper actuators and rotary actuators
P10000A GR Feedback potentiometer for damper actuators and rotary 24 VAC Transformer (AC Only) 1 10 11
actuators
P1000A GR Feedback potentiometer for damper actuators and rotary Line Blk (1) Common
actuators Volts
Red (2) Hot +
P140A GR Feedback potentiometer for damper actuators and rotary
actuators Wht (3) Y Input
1
P2800A GR Feedback potentiometer for damper actuators and rotary
actuators Pnk (4) Y Input
Position (–) 2
P5000A GR Feedback potentiometer for damper actuators and rotary Feedback VDC (+) Org (5) U Output
actuators
P500A GR Feedback potentiometer for damper actuators and rotary Floating Point
actuators
SGA24 Positioners suitable for use with the modulating damper
actuators LM..A-SR, NM..A-SR, SM..A-SR and GM..A-SR 24 VAC Transformer 1 3 5 11
ZG-R01 4 to 20 mA adaptor, 500Ω, 1/4 W resistor w 6” pigtail wires.
NSV24 US Battery back-up module for non-spring return actuators. Line Blk (1) Common
ZG-X40 120 to 24 VAC, 40 VA transformer. Volts Red (2) Hot +
Ω 500 Ω
1/4 watt
Typical Specification Control Signal (–)
Wht (3) Y Input

Date created, 02/10/2020 - Subject to change. © Belimo Aircontrols (USA), Inc.


VDC / mA (+)
Proportional control damper actuators shall be electronic direct-coupled type, 1

which require no crank arm and linkage and be capable of direct mounting 7 Pnk (4) Y Input
to a shaft from 1/4” to 1/2” diameter. Actuators must provide proportional 2

damper control response to a 2 to 10 VDC or, with the addition of a 500Ω Org (5) U Output
resistor, a 4 to 20 mA control input from an electronic controller or positioner.
Actuators shall have brushless DC motor technology and be protected from VDC/mA Control
overload at all angles of rotation. Actuators shall have manual override on the
cover. Run time shall be constant and independent of torque. Actuators shall
24 VAC Transformer (AC Only)
be cULus listed, have a 5-year warranty, and be manufactured under ISO 9001 1 8 11
International Quality Control Standards. Actuators shall be as manufactured
by Belimo. Blk (1) Common
Line
Volts Red (2) Hot +

Wht (3) Y Input


1

(–) Pnk (4) Y Input


Position 2
Feedback VDC (+) Org (5) U Output

PWM Control

800-543-9038 USA -46-


866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
MADOK
HOT WATER COILS
DUCT MOUNT
RVA:
General Contractor to provide all the duct fitting necessary to
connect all the Hot water coil with the duct works as specified in
the contract document

UNIT TAG: HW-101


QTY (1)
MODEL: 620F2-15X17­106R721

UNIT TAG: HW-102


QTY (1)
MODEL: 620F1-15X17-1010R511

UNIT TAG: HW-103,104,106


QTY (1)
MODEL: 620F1-15X17-1010R511

UNIT TAG:HW-105
QTY (1)
MODEL: 620F2-15X17-1010R511

ACCESSORIES INCLUDED:

• None. BAS contractor shall supply the hot water coil control valve.

-47-
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F2-15X17-106R721 Tag: HW-101

Coil Data
Model Number 620F2-15X17-106R721
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 2
Number Of Feeds 2
Fins Per Inch 6
Supply Connection Size 3/4"
Return Connection Size 3/4"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 50.46 ft²
Connection Type MPT
Casing Material Galvanized Steel 16 gauge
Coil Weight 30.49 lb

Air Data
Total Air Flow 824 SCFM
Air Flow Per Coil 824 SCFM
Standard Face Velocity 465.32 FPM
Altitude 0 FT
Entering Dry Bulb 57 °F
Leaving Dry Bulb 99.34 °F
Air Pressure Drop 0.12 inWG
Total Capacity 38.09 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 3.88 GPM
Fluid Velocity 2.32 FPS
Fluid Pressure Drop 1.76 ftWG
Notes

-48-
17/05/2021 MADOK MANUFACTURING INC. Page 2 of 13
-49-
17/05/2021 MADOK MANUFACTURING INC. Page 3 of 13
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F1-15X17-1010R511 Tag: HW-102

Coil Data
Model Number 620F1-15X17-1010R511
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 1
Number Of Feeds 1 RVA: Provide pipe fitting necessary
Fins Per Inch 10 to connect the hot water piping with
Supply Connection Size 1/2" the coil.
Return Connection Size 1/2"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 40.45 ft²
Connection Type MPT
Casing Material Galvanized Steel 16 gauge
Coil Weight 26.88 lb

Air Data
Total Air Flow 968 SCFM
Air Flow Per Coil 968 SCFM
Standard Face Velocity 546.64 FPM
Altitude 0 FT
Entering Dry Bulb 57 °F
Leaving Dry Bulb 86.28 °F
Air Pressure Drop 0.11 inWG
Total Capacity 30.95 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 3.15 GPM
Fluid Velocity 3.76 FPS
Fluid Pressure Drop 3.52 ftWG
Notes

-50-
17/05/2021 MADOK MANUFACTURING INC. Page 4 of 13
-51-
17/05/2021 MADOK MANUFACTURING INC. Page 5 of 13
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F1-15X17-1010R511 Tag: HW-103

Coil Data
Model Number 620F1-15X17-1010R511
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 1
Number Of Feeds 1
Fins Per Inch 10
Supply Connection Size 1/2"
Return Connection Size 1/2"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 40.45 ft²
Connection Type MPT
RVA: the max flow is 389 L/s
Casing Material Galvanized Steel 16 gauge
(824 cfm) and the minimum flow
Coil Weight 26.88 lb
is 243 L/s (515 CFM) as spe-
cified in the contract drawing
Air Data
M107, the coil should be able to
Total Air Flow 389 SCFM
operate on this range of flow
Air Flow Per Coil 389 SCFM
Standard Face Velocity 219.67 FPM
Altitude 0 FT
RVA: Provide hot water coil
Entering Dry Bulb 57 °F
with a capacity of 7.8 KW as
Leaving Dry Bulb 96.95 °F
specified in drawing M107 in
Air Pressure Drop 0.02 inWG
the contract document
Total Capacity 16.97 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 1.73 GPM
Fluid Velocity 2.06 FPS
Fluid Pressure Drop 1.14 ftWG
Notes

-52-
17/05/2021 MADOK MANUFACTURING INC. Page 6 of 13
-53-
17/05/2021 MADOK MANUFACTURING INC. Page 7 of 13
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F1-15X17-1010R511 Tag: HW-104

Coil Data
Model Number 620F1-15X17-1010R511
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 1
Number Of Feeds 1
Fins Per Inch 10
Supply Connection Size 1/2"
Return Connection Size 1/2"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 40.45 ft²
Connection Type MPT
RVA: the max flow is 336 L/s
Casing Material Galvanized Steel 16 gauge
(712 CFM) and the minimum
Coil Weight 26.88 lb
flow is 244 L/s (517 CFM) as
specified in the contract drawing
Air Data M107, the coil should be able to
Total Air Flow 336 SCFM operate on this range of flow
Air Flow Per Coil 336 SCFM
Standard Face Velocity 189.74 FPM
Altitude 0 FT
RVA: Provide hot water coil
Entering Dry Bulb 57 °F
with a capacity of 7.8 KW as
Leaving Dry Bulb 98.73 °F
specified in drawing M107 in
Air Pressure Drop 0.02 inWG
the contract document
Total Capacity 15.31 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 1.56 GPM
Fluid Velocity 1.86 FPS
Fluid Pressure Drop 0.94 ftWG
Notes

-54-
17/05/2021 MADOK MANUFACTURING INC. Page 8 of 13
-55-
17/05/2021 MADOK MANUFACTURING INC. Page 9 of 13
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F1-15X17-1010R511 Tag: HW-105

Coil Data
Model Number 620F1-15X17-1010R511
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 1
Number Of Feeds 1
Fins Per Inch 10
Supply Connection Size 1/2"
Return Connection Size 1/2"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 40.45 ft²
Connection Type MPT
Casing Material Galvanized Steel 16 gauge
Coil Weight 26.88 lb

Air Data
Total Air Flow 868 SCFM
Air Flow Per Coil 868 SCFM
Standard Face Velocity 490.16 FPM
Altitude 0 FT
Entering Dry Bulb 57 °F
Leaving Dry Bulb 87.51 °F
Air Pressure Drop 0.09 inWG
Total Capacity 28.91 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 2.95 GPM
Fluid Velocity 3.52 FPS
Fluid Pressure Drop 3.1 ftWG
Notes

-56-
17/05/2021 MADOK MANUFACTURING INC. Page 10 of 13
-57-
17/05/2021 MADOK MANUFACTURING INC. Page 11 of 13
Hot Water Coil Report

Customer Name Carrier Enterprise Date 5/17/2021, 10:04:42 AM


Contact Doug Roberts Reference Murray School
Phone 9055614461 x1 PreparedBy Brian Deryck
Email doug.roberts@carrierenterprise.com Project 58375

Model Number: 620F1-15X17-1010R511 Tag: HW-106

Coil Data
Model Number 620F1-15X17-1010R511
Coil Quantity 1
Finned Height 15 In
Finned Length 17 In
Rows Deep 1
Number Of Feeds 1
Fins Per Inch 10
Supply Connection Size 1/2"
Return Connection Size 1/2"
Tube Material Copper - 0.020
Tube Diameter 5/8
Fin Material Aluminum 0.01
Fin Surface Corrugated
Face Area 1.77 ft²
External Surface Area 40.45 ft²
Connection Type MPT
RVA: the max flow is 341 L/s
Casing Material Galvanized Steel 16 gauge
(722.92 CFM) and the minimum
Coil Weight 26.88 lb
flow is 243 L/s (115CFM) as
specified in the contract drawing
Air Data M107, the coil should be able to
Total Air Flow 341 SCFM operate on this range of flow
Air Flow Per Coil 341 SCFM
Standard Face Velocity 192.56 FPM
Altitude 0 FT
RVA: Provide hot water coil
Entering Dry Bulb 57 °F
with a capacity of 7.8 KW as
Leaving Dry Bulb 98.55 °F
specified in drawing M107 in
Air Pressure Drop 0.02 inWG
the contract document
Total Capacity 15.47 MBH

Fluid Data
Fluid Type Water
Fluid Ratio 0%
Entering Fluid Temp 160 °F
Leaving Fluid Temp 140 °F
Fluid Flow Rate(Per Coil) 1.58 GPM
Fluid Velocity 1.88 FPS
Fluid Pressure Drop 0.96 ftWG
Notes

-58-
17/05/2021 MADOK MANUFACTURING INC. Page 12 of 13
-59-
17/05/2021 MADOK MANUFACTURING INC. Page 13 of 13
24AHA SERIES
14 SEER CONDENSING UNIT
R-410A REF.

RVA: Contractor to coordinate the


support of the CU-101 as show in
the structural drawing.

UNIT TAG: CU-101


QTY (1)
MODEL: 24AHA460A005

ACCESSORIES INCLUDED:

• LOW AMBIENT CONTROLLER (ALLOWS MECHANICAL COOLING


DOWN TO -20F)
• WIND BAFFLE
• CRANKCASE HEATER
• WINTER START CONTROL, HIGH AND LOW PRESSURE SWITCHES

-60-
24AHA4
Performance Series Air Conditioner
with Puron Refrigerant
1-1/2 to 5 Nominal Tons
Lorem ipsum

Product Data
TABLE OF CONTENTS

INDUSTRY LEADING FEATURES / BENEFITS ........................1


MODEL NUMBER NOMENCLATURE........................................2
PHYSICAL DATA...........................................................................2
REFRIGERANT PIPING LENGTH LIMITATIONS .....................3
VAPOR LINE SIZING AND COOLING CAPACITY LOSS ........5
ACCESSORIES................................................................................6
ELECTRICAL DATA......................................................................8
DIMENSIONS-ENGLISH ...............................................................9
DIMENSIONS-SI.............................................................................10
TESTED AHRI COMBINATION RATINGS*...............................11
DETAILED COOLING CAPACITIES ...........................................12
CONDENSER ONLY RATINGS....................................................15
GUIDE SPECIFICATIONS .............................................................17
PRODUCTS .....................................................................................17

Fig. 1 — 24AHA4 Unit INDUSTRY LEADING FEATURES /


NOTE: Images are for illustration purposes only. Actual models may BENEFITS
differ slightly.
Energy Efficiency
Carrier air conditioners with Puron refrigerant provide a collection • 14 SEER/11.7 - 12.2 EER
of features unmatched by any other family of equipment. The
24AHA4 has been designed utilizing Carrier’s Puron refrigerant. (Based on tested combinations)
This environmentally sound refrigerant allows you to make a Sound
responsible decision in the protection of the earth’s ozone layer. • Levels as low as 66 dBA
NOTE: Ratings contained in this document are subject to change Design Features
at any time. Always refer to the AHRI directory (www.ahridirec- • Small footprint
tory.org) for the most up-to-date ratings information. • WeatherArmor cabinet
- All steel cabinet construction
- Mesh coil guard
RVA: Contractor to coordinate the refrigeration Reliability, Quality and Toughness
pipe size, length and connection with the CC-101. • Scroll compressor
• Factory-supplied filter drier
• High pressure switch
• Line lengths up to 250ft (76.2 m)
• Low ambient operation (down to -20F/-28.9C with low ambient
accessories)

-61-
Specifications subject to change without notice.
MODEL NUMBER NOMENCLATURE
1 2 3 4 5 6 7 8 9 10 11 12 13
N N A A A/N N N N A/N A/N A/N N N
2 4 A H A 4 1 8 A 0 0 3 0
Product Product Product Major Minor
Series Family Type Series SEER Variations Open Open Voltage Series
3=208/
H= Cooling Capacity 230-1
24 = AC A = AC Horizontal 4 = 14 A= 0 = Not 0 = Not 5=208/ 0, 1, 2...
Discharge SEER Standard Defined Defined 230-3
6=460/3

Use of the AHRI Certified


TM Mark indicates a
manufacturer’s
participation in the
program For verification
of certification for individual
products, go to
www.ahridirectory.org.

PHYSICAL DATA
UNIT SIZE-SERIES 18-30 24-30 30-30 36-30, 50, 60 48-30, 50, 60 60-30, 50, 60

Compressor Type Scroll

REFRIGERANT Puron® (R-410A)

Charge lb (kg) 6.40 (2.90) 6.50 (2.95) 8.60 (3.90) 8.90 (4.04) 9.00 (4.08) 10.60 (4.81)

Cond Fan Propeller Type, Direct Drive

Air Discharge Horizontal

Air Qty (CFM) 1285 1285 1900 2615 2615 2785

Motor HP 1/12 1/12 1/10 1/4 1/4 1/4

Motor RPM 800 800 800 800 800 800

Cond Coil

Face Area (Sq ft) 7.3 7.3 12.1 12.1 12.1 14.1

Fins per In. 20 20 20 20 20 20

Rows 2 2 2 2 2 2

Circuits 3 3 3 3 3 4

Valve Connect. (In. ID)

Vapor 5/8 3/4 3/4 7/8 7/8 7/8

Liquid 3/8

Refrigerant Tubes* (In. OD)

Rated Vapor* 5/8 3/4 3/4 7/8 7/8 1 1/8

Max Liquid Line 3/8

* Units are rated with 25 ft. (7.6 m) of lineset length. Review the VAPOR LINE SIZING AND COOLING CAPACITY LOSS section when using other lineset sizes and lengths of
lineset.
Note: Review the unit’s Installation Instructions for proper installation guidance.
Liquid Line Sizing For Cooling Only Systems with Puron Refrigerant tables.

2
-62-
Specifications subject to change without notice. 24AHA4-06PD
REFRIGERANT PIPING LENGTH LIMITATIONS
Liquid Line Sizing and Maximum Total Equivalent Lengths for Cooling Only Systems with Puron Refrigerant:
The maximum allowable length of a residential split system depends on the liquid line diameter and vertical separation between the indoor and
outdoor units. Review “Maximum Total Equivalent Length Outdoor Unit BELOW Indoor Unit,” for the liquid line sizing and maximum
lengths.
Maximum Total Equivalent Length Outdoor Unit BELOW Indoor Unit

LIQUID LINE AC WITH PURON REFRIGERANT MAXIMUM TOTAL EQUIVALENT LENGTH:


LIQUID LINE DIAM. OUTDOOR UNIT BELOW INDOOR VERTICAL SEPARATION FT (M)
SIZE CONNECTION W/ TXV
(IN. OD) (IN. OD) 0-5 6-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80
(0-1.5) (1.8-3.0) (3.4-6.1) (6.4-9.1) (9.4-12.2) (12.5-15.2) (15.5-18.3) (18.6-21.3) (21.6-24.4)
1/4 150 150 125 100 100 75 -- -- --
018
AC with 3/8 5/16 250* 250* 250* 250* 250* 250* 250* 225* 150
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250* 250*
1/4 75 75 75 50 50 -- -- -- --
024
AC with 3/8 5/16 250* 250* 250* 250* 250* 225* 175 125 100
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250* 250*
1/4 30 -- -- -- -- -- -- -- --
030
AC with 3/8 5/16 175 225* 200 175 125 100 75 -- --
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250* 250*

036 5/16 175 150 150 100 100 100 75 -- --


AC with 3/8
Puron 3//8 250* 250* 250* 250* 250* 250* 250* 250* 250*

048
AC with 3/8 3/8 250* 250* 250* 250* 250* 250* 230 160 --
Puron

060
AC with 3/8 3/8 250* 250* 250* 225* 190 150 110 -- --
Puron

* Maximum actual length not to exceed 200 ft (61 m)


Total equivalent length accounts for losses due to elbows or fitting. See the Long Line Guideline for details.
-- = outside acceptable range
Maximum Total Equivalent Length Outdoor Unit ABOVE Indoor Unit

AC WITH PURON REFRIGERANT MAXIMUM TOTAL EQUIVALENT LENGTH:


LIQUID LINE LIQUID LINE OUTDOOR UNIT ABOVE INDOOR VERTICAL SEPARATION FT (M)
SIZE CONNECTION DIAM. W/
(IN. OD) TXV (IN. OD) 25 26-50 51-75 76-100 101-125 126-150 151-175 176-200
(7.6) (7.9-15.2) (15.5-22.9) (23.2-30.5) (30.8-38.1) (38.4-45.7) (46.0-53.3) (53.6-61.0)
1/4 175 250* 250* 250* 250* 250* 250* 250*
018
AC with 3/8 5/16 250* 250* 250* 250* 250* 250* 250* 250*
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250*

1/4 100 125 175 200 225* 250* 250* 250*


024
AC with 3/8 5/16 250* 250* 250* 250* 250* 250* 250* 250*
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250*

1/4 30 -- -- -- -- -- -- --
030
AC with 3/8 5/16 250* 250* 250* 250* 250* 250* 250* 250*
Puron
3/8 250* 250* 250* 250* 250* 250* 250* 250*

036 5/16 225* 250* 250* 250* 250* 250* 250* 250*
AC with 3/8
Puron 3/8 250* 250* 250* 250* 250* 250* 250* 250*
048
AC with 3/8 3/8 250* 250* 250* 250* 250* 250* 250* 250*
Puron
060
AC with 3/8 3/8 250* 250* 250* 250* 250* 250* 250* 250*
Puron

* Maximum actual length not to exceed 200 ft (61 m)

-63-
 Total equivalent length accounts for losses due to elbows or fitting. See “LONG-LINE APPLICATIONS,” for details.
-- = outside acceptable range

24AHA4-06PD Specifications subject to change without notice. 3


REFRIGERANT CHARGE ADJUSTMENTS
LIQUID LINE SIZE (IN. OD) PURON CHARGE OZ/FT (G/M)

3/8 0.60 (17.74) (Factory charge for lineset = 9 oz / 266.16 g)

5/16 0.40 (11.83)

1/4 0.27 (7.98)

Units are factory charged for 15 ft (4.6 m) of 3/8” liquid line. The LONG-LINE APPLICATIONS
factory charge for 3/8” lineset 9 oz (266.16 g). When using other An application is considered Long-Line, when the refrigerant level in
length or diameter liquid lines, charge adjustments are required per the the system requires the use of accessories to maintain acceptable
REFRIGERANT CHARGE ADJUSTMENTS table. refrigerant management for systems reliability. See ACCESSORY
Charging Formula: USAGE GUIDELINES on page 7 for the required accessories.
[(Lineset oz/ft x total length) – (factory charge for lineset)] = Defining a system as long-line depends on the liquid line diameter,
charge adjustment actual length of the tubing, and vertical separation between the indoor
and outdoor units.
Example 1: System has 15 ft of line set using existing 1/4 “liquid line.
What charge adjustment is required? For air conditioner systems, the “AC WITH PURON
REFRIGERANT LONG-LINE DESCRIPTION ft (m)” table shows
Formula:
when an application is considered long-line.
(.27 oz/ft x 15ft) – (9 oz) = (4.95) oz.
Net result is to remove 4.95 oz of refrigerant from the system
Example 2: System has 45 ft of existing 5/16” liquid line. What is the
charge adjustment?
Formula:
(.40 oz/ft. x 45ft) – (9 oz.) = 9 oz.
Net result is to add 9 oz of refrigerant to the system

AC WITH PURON REFRIGERANT LONG-LINE DESCRIPTION ft (m)


Beyond these lengths, long line accessories are required

LIQUID LINE SIZE UNITS ON SAME LEVEL - FT (M) OUTDOOR BELOW INDOOR - FT (M) OUTDOOR ABOVE INDOOR
(IN. OD) - FT (M)

1/4 No accessories needed within allowed lengths No accessories needed within allowed lengths 175 (53.3)

5/16 120 (36.6) 50 (15.2) vertical or 120 (36.6) total 120 (36.6)

3/8 80 (24.4) 35 (10.7) vertical or 80 24.4) total 80 (24.4)

4
-64-
Specifications subject to change without notice. 24AHA4-06PD
VAPOR LINE SIZING AND COOLING CAPACITY LOSS
LONG LINE APPLICATION: An application is considered “long- The maximum vertical separation is 200 ft. (60.96 m) when the
line” when the total equivalent tubing length exceeds 80 ft. (24.4 m) or outdoor unit is above the indoor unit, and up to 80 ft. (24.4 m) when
when there is more than 20 ft. (6.09 m) vertical separation between the the outdoor unit is below the indoor unit. Refer to the ACCESSORY
indoor and outdoor units. These applications require additional USAGE GUIDELINES on page 7 for required accessories. See the
accessories and system modifications for reliable system operation. The Long-line Application Guideline for required piping and system
maximum allowable total equivalent length is up to 250 ft. (76.2 m). modifications. Also, refer to the “Vapor Line Sizing and Cooling
Capacity Losses — Puron Refrigerant 1-Stage Air Conditioner
Applications” table for the vapor tube diameters based on the total
length to minimize the cooling capacity loss.

Vapor Line Sizing and Cooling Capacity Losses — Puron Refrigerant 1-Stage Air Conditioner Applications
MAXIMUM COOLING CAPACITY LOSS (%) TOTAL EQUIVALENT LINE LENGTH FT. (M)
UNIT LIQUID LINE VAPOR LINE
NOMINAL DIAMETERS 26-50 51-80 81-100 101-125 126-150 151-175 176-200 201-225 226-250
SIZE (BTUH) DIAMETERS (IN. OD)
(IN. OD) (7.9-15.2) (15.5-24.4) (24.7-30.5) (30.8-38.1) (38.4-45.7) (46.0-53.3) (53.6-61.0) (61.3-68.6) (68.9-76.2)
018 1/2 1 2 3 5 6 7 8 9 11
1 Stage 3/8 5/8 0 1 1 1 2 2 2 3 3
AC with
Puron 3/4 0 0 0 0 1 1 1 1 1
024 5/8 0 1 2 2 3 3 4 5 5
1 Stage 3/4 0 0 1 1 1 1 1 2 2
AC with 3/8
Puron 7/8 0 0 0 0 0 1 1 1 1
030 5/8 1 2 3 3 4 5 6 7 8
1 Stage 3/4 0 0 1 1 1 2 2 2 3
3/8
AC with
Puron 7/8 0 0 0 0 1 1 1 1 1
036 5/8 1 2 4 5 6 8 9 10 12
1 Stage 3/4 0 1 1 2 2 3 3 4 4
AC with 3/8
Puron 7/8 0 0 0 1 1 1 1 2 2
048 3/4 0 1 2 3 4 5 5 6 7
1 Stage 7/8 0 0 1 1 2 2 2 3 3
3/8
AC with
Puron 1 1/8 0 0 0 0 0 0 0 1 1
060 3/4 1 2 4 5 6 7 9 10 11
1 Stage 3/8 7/8 0 1 2 2 3 4 4 5 5
AC with
Puron 1 1/8 0 0 0 1 1 1 1 1 1

*Applications in this area may be long- line and may have height restrictions. See LONG-LINE APPLICATIONS on page 4.

24AHA4-06PD
-65-
Specifications subject to change without notice. 5
ELECTRICAL DATA
UNIT SIZE - OPER VOLTS* COMPR FAN MAX FUSE** OR
VOLTAGE, SERIES V/PH MCA CKT BRK AMPS
MAX MIN LRA RLA FLA
18-30 56.3 9.0 0.50 11.8 20
24-30 62.9 10.9 0.50 14.1 25
30-30 73.0 14.1 0.70 18.3 30
208/230/1 253 197
36-30 77.0 14.1 1.20 18.8 30
48-30 124.0 18.5 1.20 24.3 40
60-30 152.5 23.7 1.45 31.1 50
36-50 71.0 9.0 1.20 12.5 20
48-50 208/230/3 253 197 83.1 13.7 1.20 18.3 30
60-50 110.0 15.9 1.45 21.4 35
36-60 38.0 5.6 0.60 7.6 15
48-60 460/3 506 414 41.0 6.2 0.60 8.4 15
60-60 52.0 7.1 0.80 9.7 15
LEGEND:
FLA - Full Load Amps * Permissible limits of the voltage range at which the unit operates satisfactorily
HACR - Heating, Air Conditioning, Refrigeration ** Time-Delay fuse.
LRA - Locked Rotor Amps Complies with 2007 requirements of ASHRAE Standards 90.1
NEC - National Electrical Code
RLA - Rated Load Amps (compressor)

A−WEIGHTED SOUND POWER (dBA)


TYPICAL OCTAVE BAND SPECTRUM (DBA, WITHOUT TONE ADJUSTMENT)
UNIT SIZE STANDARD RATING (DBA)
125 250 500 1000 2000 4000 8000
18 69 50.5 57.0 59.5 64.5 60.5 53.5 43.0
24 66 50.5 58.5 60.5 59.5 56.5 51.0 41.5
30 68 55.5 59.5 61.5 63.5 60.0 58.0 49.5
36 71 59.5 59.5 62.0 65.5 63.5 62.0 55.0
48 70 57.5 59.5 64.0 66.0 63.0 60.5 54.5
60 73 60.0 61.5 64.5 67.0 66.0 65.5 58.0
NOTE: Tested in accordance with AHRI Standard 270-08 (not listed in AHRI).
A−WEIGHTED SOUND POWER (dBA) WITH ACCESSORY SOUND SHIELD
TYPICAL OCTAVE BAND SPECTRUM (DBA, WITHOUT TONE ADJUSTMENT)
UNIT SIZE STANDARD RATING (DBA)
125 250 500 1000 2000 4000 8000
18 68 52.5 58.0 58.5 64.5 59.5 52.5 42.5
24 65 54.5 57.5 59.5 59.0 56.0 50.5 40.5
30 68 55.0 60.0 61.5 62.5 60.0 58.0 49.5
36 71 59.5 59.5 62.5 65.0 63.0 61.5 55.0
48 70 57.5 59.5 63.0 65.0 62.5 60.0 54.0
60 73 61.0 62.0 64.0 67.0 65.5 65.5 57.5
NOTE: Tested in accordance with AHRI Standard 270-08 (not listed in AHRI).

SOUND PRESSURE LEVELS, (dBA)


UNIT SIZE AT DISTANCE 10' FROM UNIT AT DISTANCE 15' FROM UNIT AT DISTANCE 20' FROM UNIT
18 51.5 48.0 45.5
24 48.5 45.0 42.5
30 50.5 47.0 44.5
36 53.5 50.0 47.5
48 52.5 49.0 46.5
60 55.5 52.0 49.5

NOTE: Sound pressure data vs distance converted using AHRI 275 Standard under certain environmental and layout assumptions.
CHARGING SUB−COOLING (TXV−TYPE EXPANSION DEVICE
UNIT SIZE-SERIES REQUIRED SUBCOOLING °F (°C)
18 12 (6.7)
24 12 (6.7)
30 12 (6.7)
36 8 (4.4)
48 12 (6.7)
60 10 (5.6)

-66-
NOTE: The conversion is accurate only when all the assumptions are correct.

8 Specifications subject to change without notice. 24AHA4-06PD


DIMENSIONS-ENGLISH
Operating Shipping
Electrical Shipping Dimensions
UNIT Series A B C D E F G H J K L M N P Weight Weight
Characteristics (L x W x H)
(lbs) (lbs)
24AHA418 0 X 0 0 0 31 1/8” 36 15/16” 14 9/16” 16” 23 7/16” 17 3/16” 23 1/8” 28 1/16” 13” 6 5/8” 11 1/4” 5/8” 2 7/8” 5 13/16” 146 166 42 15/16” x 18” x 34 1/8”
24AHA424 0 X 0 0 0 31 1/8” 36 15/16” 14 9/16” 16” 23 7/16” 17 3/16” 23 1/8” 28 1/16” 14” 6 3/4” 11 5/8” 3/4” 2 7/8” 5 13/16” 148 168 42 15/16” x 18” x 3 4 1/8”
24AHA430 0 X 0 0 0 37 1/8” 44 1/2” 17 1/16” 18 7/16” 30 1/2” 19 5/8” 29 1/8” 34 1/16” 13 11/16” 8 1/8” 15 7/8” 3/4” 3 3/8” 6 3/8” 183 213 50 1/2” x 20 1/2” x 40 1/8”
24AHA436 0 X 0 X X 37 1/8” 44 1/2” 17 1/16” 18 7/16” 30 1/2” 19 5/8” 29 1/8” 34 1/16 13 11/16” 8 1/8” 15 7/8” 7/8” 3 3/8” 6 3/8” 184 214 50 1/2” x 20 1/2” x 40 1/8”
24AHA448 0 X 0 X X 37 1/8” 44 1/2” 17 1/16” 18 7/16” 30 1/2” 19 5/8” 29 1/8” 34 1/16 14 1/2” 8 1/2” 18 7/8” 7/8” 3 3/8” 6 3/8” 213 243 50 1/2” x 20 1/2” x 40 1/8”
24AHA460 0 X 0 X X 43 1/8” 44 1/2” 17 1/16” 18 7/16” 30 1/2” 19 5/8” 35 1/8” 40 1/16” 14 1/2” 8 1/2” 18 7/8” 7/8” 3 3/8” 6 3/8” 245 275 50 1/2” x 20 1/2” x 46 1/8”
208-230-1-60

208/230-3-60
203-1-60

460-3-60

1. Clearance Requirements:
X = YES a. Single Unit Applications:
0 = NO With the coil facing the wall, allow 6in (152mm) minimum
AIR clearance on the coil side, the coil end, and allow 20in (508mm)
minimum clearance on the fan side.
With the fan facing the wall, allow 8in (203mm) minimum
7 1/2” 2 1/2” clearance on the fan side, 6in (152mm) on the coil end and 20in
(508mm) minimum clearance on the coil side.
b. Multi Unit Applications:
4 3/16” Allow 24in (610mm) minimum clearance between the fan and the
coil sides of the multiple units. Arrange the units so the discharge
of one unit does not enter the inlet of the other unit. When two
units are installed end to end with the coil ends facing each other
allow 12in (305mm) in minimum clearance between the units.
11/16” c. Compressor End Service Clearance:
AIR Allow 24in (610mm) minimum clearance on the compressor end
when the units are stacked or there is less than 40 in. (1016mm) of
Fig. 2 — Dimensions clearance above the top of the unit. If there is 40 in. (1016mm) of
clearance above the unit and top panel is accessible for removal,
allow 8in (203mm) minimum clearance minimum clearance on the
compressor end for service.

IMPORTANT: When installing single or multiple units in an alcove,


roof well, or partially enclosed area, ensure there is adequate ventilation to
prevent recirculation of discharged air.
2. Minimum outdoor operating ambient in the COOLING mode is
55F (13C) and a maximum of 125F (52C).
3. Series designation is the 13th position of the unit model number
4. Center of gravity
5. All dimensions are in inches unless noted.

FIELD POWER SUPPLY CONN


JUNCTION BOX FOR HOLE SIZES PROVIDED:
POWER SUPPLY AND 7/8” HOLD WITH
CONTROL CONNECTIONS 1 1/8” KNOCKOUT AND
1 7/16” 1 3/8” KNOCKOUT
FIELD CONTROL SUPPLY
WIRE ENTRY
7/8” HOLE W/GROMMET
1 7/16”

M VAPOR LINE CONN.


FEMALE SWEAT CONN.

8 1/16”

3/8’ LIQUID LINE


1” 4 1/12”
FEMALE SWEAT CONN.

Fig. 3 — Dimensions

MINIMUM MOUNTING
UNIT SIZE
PAD DIMENSIONS
18,24 23” x 42”

-67-
30,36,48,60 24” x 50”

24AHA4-06PD Specifications subject to change without notice. 9


CONDENSER ONLY RATINGS (CONT.)
CONDENSER ENTERING AIR TEMPERATURES °F (°C)
SST °F (°C)
55°F (12.78°C) 65°F (18.33°C) 75°F (23.89°C) 85°F (29.44°C) 95°F (35.0°C) 105°F (40.56°C) 115°F (46.11°C) 125°F (51.67°C)
24AHA436A30
TCG 31.40 29.80 28.20 26.40 24.60 22.70 20.60 18.50
30°F (-1.11°C) SDT 68.70 78.10 87.50 96.80 106.20 115.50 124.70 134.00
KW 1.48 1.69 1.91 2.14 2.40 2.69 3.04 3.44
TCG 34.70 32.90 31.10 29.20 27.20 25.10 22.80 20.50
35°F (1.67°C) SDT 70.00 79.30 88.60 97.90 107.20 116.40 125.60 134.80
KW 1.48 1.70 1.91 2.15 2.41 2.70 3.05 3.45
TCG 38.20 36.20 34.20 32.10 29.90 27.60 25.20 22.60
40°F (4.44°C) SDT 71.30 80.50 89.80 99.10 108.30 117.40 126.50 135.60
KW 1.49 1.70 1.92 2.16 2.42 2.72 3.06 3.45
TCG 42.00 39.80 37.60 35.30 32.90 30.30 27.70 24.80
45°F (7.22°C) SDT 72.80 81.90 91.10 100.30 109.40 118.50 127.50 136.40
KW 1.50 1.72 1.94 2.18 2.44 2.73 3.07 3.46
TCG 46.00 43.60 41.10 38.60 36.00 33.20 30.20 27.20
50°F (10.0°C) SDT 74.40 83.40 92.50 101.60 110.60 119.60 128.50 137.30
KW 1.52 1.74 1.96 2.20 2.46 2.75 3.08 3.47
TCG 50.20 47.60 44.90 42.10 39.20 36.20 32.90 29.60
55°F (12.78°C) SDT 76.10 85.00 94.00 103.00 111.90 120.80 129.50 138.20
KW 1.54 1.76 1.98 2.22 2.48 2.77 3.10 3.48
24AHA448A30
TCG 41.50 39.50 37.40 35.40 33.20 30.80 28.20 25.40
30°F (-1.11°C) SDT 73.40 82.60 91.90 101.20 110.40 119.50 128.60 137.50
KW 2.05 2.30 2.57 2.87 3.21 3.60 4.05 4.56
TCG 45.70 43.40 41.20 38.90 36.50 33.90 31.10 28.10
35°F (1.67°C) SDT 75.10 84.30 93.40 102.60 111.70 120.80 129.70 138.60
KW 2.08 2.33 2.60 2.90 3.24 3.63 4.08 4.60
TCG 50.10 47.70 45.20 42.70 40.10 37.20 34.20 30.90
40°F (4.44°C) SDT 77.00 86.00 95.10 104.10 113.20 122.10 131.00 139.70
KW 2.12 2.36 2.63 2.93 3.27 3.67 4.12 4.64
TCG 54.80 52.20 49.50 46.70 43.80 40.70 37.40 33.80
45°F (7.22°C) SDT 78.90 87.80 96.80 105.80 114.70 123.50 132.20 140.80
KW 2.15 2.39 2.66 2.96 3.31 3.71 4.16 4.69
TCG 59.90 56.90 54.00 51.00 47.80 44.40 40.70 36.80
50°F (10.0°C) SDT 80.90 89.80 98.60 107.50 116.30 125.00 133.60 142.00
KW 2.19 2.43 2.70 3.00 3.34 3.74 4.20 4.72
TCG 65.20 62.00 58.80 55.40 51.90 48.20 44.20 39.90
55°F (12.78°C) SDT 83.10 91.80 100.50 109.30 117.90 126.50 134.90 143.20
KW 2.24 2.47 2.73 3.03 3.38 3.78 4.24 4.76
24AHA460A30
TCG 53.00 50.30 47.70 45.10 42.40 39.40 36.00 32.40
30°F (-1.11°C) SDT 76.00 85.10 94.30 103.50 112.70 121.70 130.60 139.40
KW 2.59 2.90 3.23 3.61 4.03 4.52 5.08 5.71
TCG 58.30 55.30 52.50 49.70 46.60 43.30 39.70 35.70
35°F (1.67°C) SDT 78.00 87.00 96.10 105.20 114.20 123.10 131.90 140.60
KW 2.64 2.94 3.28 3.65 4.08 4.58 5.14 5.78
TCG 63.90 60.70 57.60 54.50 51.10 47.50 43.60 39.30
40°F (4.44°C) SDT 80.00 88.90 97.90 106.90 115.80 124.70 133.30 141.90
KW 2.69 2.99 3.32 3.70 4.14 4.63 5.20 5.84
TCG 70.00 66.50 63.10 59.60 55.90 51.90 47.60 42.90
45°F (7.22 °C) SDT 82.20 91.00 99.90 108.80 117.60 126.30 134.80 143.20
KW 2.74 3.04 3.38 3.76 4.19 4.69 5.27 5.91
TCG 76.40 72.60 68.80 65.00 60.90 56.50 51.80 46.70
50°F (10.0°C) SDT 84.60 93.30 102.00 110.70 119.40 127.90 136.30 144.50
KW 2.80 3.10 3.43 3.81 4.25 4.76 5.33 5.97
TCG 83.30 79.10 74.90 70.60 66.10 61.30 56.10 50.60
55°F (12.78°C) SDT 87.00 95.60 104.20 112.80 121.20 129.60 137.80 145.80
KW 2.86 3.15 3.49 3.87 4.31 4.82 5.39 6.04

* AHRI listing applies only to systems shown in Combination Ratings table.


• KW - Outdoor Unit Kilowatts Only.
• SDT - Saturated Temperature Leaving Compressor (°F)
• SST - Saturated Temperature Entering Compressor (°F/°C)

-68-
• TCG - Gross Cooling Capacity (1000 Btuh)

16 Specifications subject to change without notice. 24AHA4-06PD

You might also like