Professional Documents
Culture Documents
DR Engp 1.1 R 6
DR Engp 1.1 R 6
TITLE: Piping Standard and Material for Oil Production and Process Facilities
PART:
CHAPTER:
DR-ENGP-1.1-R.6
Note: For requisition of materials referred here through their TAG’s, materials
standardization PM-1/2 of the Petrobras / E&P, shall be used.
Index
Appendix Index
7 – Valves descriptions.
8 – Piping material descriptions.
Exemplo:
Sequencial number
Nominal diameter:
2 – Reference Standards
STANDARD TITLE
API STD 600 ISO 10434 – Bolted Bonnet Steel Gate Valves for
Petroleum and Natural Gas Industries.
API STD 609 Butterfly Valves: Double Flanged, Lug and Wafer
– Type.
ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread
Form).
ASME B16.5 Pipe flanges and flanged fittings NPS 1/2 through
NPS 24 metric/inch standard revision e ASME
B16.5
STANDARD TITLE
STANDARD TITLE
STANDARD TITLE
STANDARD TITLE
BSI BS 1873 Stell Globe and Globe Stop and Check Valves
(flanged and butt-welding ends) for the Petroleum,
Petrochemical and Allied Industries.
BSI BS 5152 Cast Iron Globe and Globe Stop and Check
Valves for General Purposes.
STANDARD TITLE
3 – Abbreviations
BF - Strap-Flange
BS - British Standards
BUJ - Plug
CL - Class
CR - Chrome
CRUZ - Cross
Cu-Ni - Copper/Nikel
DN - Nominal Diameter
FLG - Flange
FF - Flat Face
RF - Raised Face
GALV - Galvanized
GR - Grade
HEX - Hexagonal
IN - Inch
J - Joint
JA - Ring Joint
JE - Spiral Wound
JI - Insulated Joint
JO - Elbow
L - Coupling
MAX - Maximum
ML - Half Coupling
NIP - Nipple
PE - Polyethylene
RED - Reduction
SCH - Schedule
STD - Standard
SW - Socket Weld
TAM - Plug
TEMP - Temperature
THD - Threaded
UN - Union
VB - Butterfly Valve
VE - Ball Valve
VG - Gate Valve
VR - Check Valve
XS - Extra Strong
WN - Welding Neck
(*) Maximum Working Pressure (psig), according to the table – Temperature and Pressure Limit, of the
respective Spec.
B20 (0ºC/40ºC)
20 PVC ASTM
D1785 PVC 1120
B21 (10ºC/80ºC)
21 CPVC ASTM
F441 CPVC 4120
B22(90ºC/100PSIG)
(60º - 145 PSIG)
22 FRP ASTM F1173
Nonmetallics
condutive 145
psig
B23 (90ºC/150PSIG)
(60º - 230 PSIG)
23 FRP ASTM F1173
condutive 230
psig
B24 (0ºC/120ºC)
FRP ASTM F1173
24 phenolic resin
condutive 150
psig
B25 (0ºC/80ºC)
RPVC - PVC
extruder reinforced
25
ext. with resin
poly and glass
fiber
E&P 1 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
ASME B31.3 SFW-Fire Water (Fresh) 0ºC / 90ºC (1,6 mm) 125 A4
Pipes and fittings Valves
Size
Item Tag Wall or class Ends Material Ball
(in)
THD API 5L Gr B PSL 1 Size Description Tag
T-01A 1/2" - 1 1/2" Sch 80
(Note 5) seamless
T-02A
2" - 6" Sch 40
T-02B API 5L Gr B PSL 1
T-02A seamless
8" - 12" Sch 20 or
Pipe T-02B welded ERW or ERW / HFIW
T-02A BW (E=0,85) (Note 11)
14"
T-02B Sch 10
16" - 20"
API 5L Gr B PSL 1
T-03B
24" 0,281" welded (E=0,95)
Bushing BRE-01 1/2" - 1 1/2" 6000 Gate valve; class 125; FLG; FF; cast
2" - 12" VG-34
Half Coupling ML-01 3000 iron.
ASTM A 105
Plug BUJ-01 6000 Gate valve; class 125; FLG; FF;
14" - 24" VG-35
Cap TAM-01 gear; cast iron.
THD
Union UN-01 (Note 5)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 2 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
ASME B31.3 SFW-Fire Water (Fresh) 0ºC / 90ºC (1,6 mm) 125 A4
Pressure / Temperature Rating
90 190 90 135
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Threaded connections must be weld sealed in case of vibration.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Use welding neck flanges when directly connected to buttwelding fittings.
8 For pressures above 150 psig, use VB-09 and VB-10.
9 Use plug (BUJ-01) after drains and vents blocking.
10 Isolating joint see drawing on the appendix 15.
11 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 3 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
Cap TAM-05
Union UN-04
(Notes 1 and 3)
Coupling L-04
Tee TE-02
Cross CRUZ-02
Check
Check valve, swing type, class 200,
1/2" - 1 1/2" VR-127
FLG, FF, bronze.
E&P 4 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
HWU-Utility Heating Water - Utilities; GW-Grey Water; SP-Tank Vent &
ASME B31.3
Sounding Pipe (Notes 8 and 9); WW-Sewage Waste Water
0ºC / 105ºC ______ 125 A8
Temp. (ºC) Max. press (psig) Temp. (ºC) Max. press (psig)
up to 65 200
80 194
105 185
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use niple THD X PLAIN and threaded cap (TAM-04) after drains and vents blocking.
4 Use flat face gasket (JPH-10) for gate, globe and check valves assembly. For ball valves use raised face gasket (JPH-07).
5 Piping spools must be galvanized after manufacturing to ASTM A 123.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 For onshore facilities only, stub in connections may be used according to ASME B31.3.
8 Use Spec A8 only for vent in Naval Systems.
9 On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
10 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 5 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10 and 20); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite); IA-
Instrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
ASME B31.3
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
-100ºC / 370ºC ________ 150 B3
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water; AM-Amine (Note
16).
Globe
JI-01 1/2" - 34" 1/8" (3,2 mm) Fenolic resin with neoprene Other
Stud PAE-07 ASTM A 320 Gr L7 Globe valve, needle disc; 3000
1/2" - 1" 1/2" - 1 1/2" VAG-45
Nut (Note 2) ASTM A 194 Gr 4/S3 psi; SW; stainless steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 6 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
Temp. Corrosion
CODE Service Class Standard
Range Allowance
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10 and 20); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite); IA-
Instrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
ASME B31.3
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
-100ºC / 370ºC ________ 150 B3
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water;
AM-Amine (Note 16).
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THR X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Use only downstream centrifuge.
8 When Classifier especifies metallic material, this Spec shall be used.
9 Use only downstream filters.
10 This Spec should only be used when recommended in appendix 5.
11 Pipes, connections and fittings larger than 24', only to be used in F (Flare) service.
12 For inert gas used for purge of cargo and ballast pumps in Naval Systems use only B3.
13 For sounding pipe in Naval Systems use only B3.
14 On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
15 When required Fully Tight valve (VET), see types in appendix 14.
16 Inlet from rich Amine flash drum and outlet of Amine stripper reflux drum.
17 From -101°C to -30°C material shall be solution heat-treaded.
18 Use only for AM - Amine
19 Isolating joint see drawing on the appendix 15.
20 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175).
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 07 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 HF-Hot Fluid; HWP-Process Heating Water; S-Steam; SC-Steam Condensate 0ºC / 350ºC (1,6 mm) 150 B4
Pipes and Fittings (Note 4) Valves (Note 6)
Size
Item Tag Wall or Class Ends Material Ball
(in)
Size Description Tag
T-05A 1/2" - 1 1/2" Sch 80 PLAIN API 5L Gr B PSL 1 seamless
T-02A
2" - 6" Sch 40
T-02B API 5L Gr B PSL 1
seamless or welded
8" - 12" Sch 20 ERW or ERW / HFIW
Pipe T-02A (E=0,85) (Note 7)
14" Sch 10 BW
Tee TE-05
Cross CRUZ-05
3000 SW ASTM A 105
Half Coupling ML-02
Cap TAM-05
Cap TAM-02
Other
Globe valve, needle disc; 3000
1/2" - 1 1/2" VAG-17
FLG-05E 1/2" - 1 1/2" SW (RF) PSI; SW; carbon steel.
Flange
FLG-05A 1/2" - 24" 150 BLIND (RF) ASTM A 105
(Note 5)
FLG-04A 2" - 24" WN (RF)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 08 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
HF-Hot Fluid; HWP-Process Heating Water; S-Steam; SC-Steam
ASME B31.3
Condensate
0ºC / 350ºC (1,6 mm) 150 B4
Pressure / Temperature Rating
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 When required Fully Tight valve (VET), see types in appendix 14.
7 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 09 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 FP-Production and drilling fluid 0ºC / 90ºC (3,2 mm) 150 B5
Pipes and Fittings Valves
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-05A 3/4" XXS 0,308" PLAIN API 5L Gr B PSL 1 seamless Size description Tag
2" Sch 80S 0,218" Ball valve; class 800; SW; carbon
3/4" VE-48D
3" Sch 80S 0,300" steel.
Tee TE-02
Wall
Red. Tee TRE-01 thickness ASTM A 234 Gr WPB
2" - 12" BW
Conc. Red. REDC-01 according to
pipe
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Gate (Note 4)
Globe
Check
FLG-13 WN (RTJ)
2" - 4" 600
FLG-15 BLIND (RTJ) Butterfly
FLG-04A WN (RF) Butterfly valve; wafer; max.
Flange
ASTM A 105 2" - 6" pressure 150 PSIG; ductile iron, VB-03
(Note 4) FLG-04B WN (FF) Buna-N seat.
2" - 12" 150
FLG-05A BLIND (RF) Butterfly valve; wafer; max.
2" - 6" pressure 250 PSIG; ductile iron, VB-09
FLG-05B BLIND (FF) Buna-N seat.
Butterfly valve; wafer; max.
Compressed non-asbestos
JPH-07 2" - 12" 1/16" (1,6mm) RF 8" - 12" pressure 250 PSIG; gear; ductile VB-10
(aramida fiber and NBR)
Gasket iron, Buna-N seat.
(Note 2) Carbon steel coated Zn-Ni max.
JA-01 2" - 12" 600 Oval
hardness 90 Brinell
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 10 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 FP-Production and drilling fluid 0ºC / 90ºC (3,2 mm) 150 B5
Pressure / Temperature Rating
up to 38 285
50 278
90 261
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
5 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking
6 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 11 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service (Note 6) Class Standard
Range Allowance
F-Safety System and Flare; G-Glycol; GL-Refrigerated Liquified Petroleum
-46ºC /
ASME B31.3 Gases in Low Temperature; P-Process (non-corrosive hydrocarbon )
(Note9).
240ºC
(1,6 mm) 150 B6
Pipes and Fittings (Note 5) Valves (Note 8)
Size Wall or
Item Tag Ends Material Ball
(in) Class
1/2" - 3/4" Sch 160 Size Description Tag
T-09 PLAIN
1" - 1 1/2" Ball valve; class 800; SW; carbon steel,
Sch 80 1/2" - 3/4" VE-330C
2" - 3" RPTFE® seat, up to 150ºC.
ASTM A 333 Gr 6
4" - 6" Sch 40 seamless
Ball valve; class 800; SW; carbon steel,
T-07A 1" - 1 1/2" VE-330B
8" - 12" Sch 20 RPTFE® seat, up to 150ºC.
Elbow 90º JO-17 Ball valve; class 800; SW; carbon steel,
1/2" - 3/4" VE-296C
Elbow 45º JO-18 1/2" - 3/4" PEEK® seat, over 150°C.
Cross CRUZ-12 Ball valve; class 150; FLG; RF; carbon steel,
6000 2" - 4" VE-297
Half Coupling ML-07 PEEK® seat, over 150°C.
Red. Coupling LRE-04 Ball valve; class 150; FLG; RF; gear; carbon
1/2" - 3/4" 6" - 24" VE-298
Cap TAM-12 steel, PEEK® seat, over 150°C.
Union UN-09 Ball valve; class 150; FLG; RF; gear; carbon
26" - 36" VE-298A
Coupling L-09 steel, PEEK® seat, over 150°C.
SW ASTM A 350 Gr LF2 CL 1
(Notes 1 and 5)
Elbow 90º JO-13 Ball valve; fire tested, class 800; SW; carbon
1/2" - 3/4" VE-299C
Elbow 45º JO-14 steel, RPTFE® seat, up to 150ºC.
Equal Tee TE-09 Ball valve; fire tested, class 800; SW; carbon
1" - 1 1/2" VE-299B
Red. Tee TRE-05 steel, RPTFE® seat, up to 150ºC.
Cross CRUZ-09 Ball valve; fire tested, class 150; FLG; RF;
1" - 1 1/2" 3000 2" - 4" VE-300
Half Coupling ML-05 carbon steel, RPTFE® seat, up to 150ºC.
Red. Coupling LRE-03 Ball valve; fire tested, class 150; FLG; RF;
Fittings and Accessories
Red. Nip. C NIPRC-05A Ball valve; fire tested, class 150; FLG; RF;
1/2" - 4" BW/PLAIN 2" - 4" VE-303
Red. Nip. E NIPRE-16A carbon steel, PEEK® seat, over 150°C.
S.R.ELL 90º CRC-02 2" - 24" Ball valve; fire tested, class 150; FLG; RF;
Wall 6" - 24" VE-304
L.R.ELL 90º CRL-03 gear; carbon steel, PEEK® seat, over 150°C.
thickness
L.R.ELL 45º CRL-04 according to Ball valve; fire tested, class 150; FLG; RF;
pipe ASTM A 420 Gr WPL6 26" - 36" VE-304A
Tee TE-08 gear; carbon steel, PEEK® seat, over 150°C.
FLG-45 1/2" - 1 1/2' SW (RF) Check valve; dual plate; wafer; class 150;
2" - 24" RF; carbon steel; Viton TBR-S seat (up to VR-53
FLG-23A 1/2" - 24" BLIND (RF) 200°C).
Flange Check valve; dual plate; wafer; class 150;
FLG-22A 2" - 24" 150 WN (RF) ASTM A 350 Gr LF2 CL 1
(Note 7) 26" - 36" RF; carbon steel; Viton TBR-S seat (up to VR-53A
FLG-23B BLIND (RF) 200°C).
26” - 36”
FLG-22B WN (RF) Check valve; dual plate; wafer; class 150;
2" - 24" VR-71
Stainless steel AISI 304 with RF; carbon steel; metal-metal (over 200°C).
JE-04 1/2" - 6"
flexible-graphite
Check valve; dual plate; wafer; class 150;
Gasket JE-05 8" - 24" 0,175" (4,4mm) RF Stainless steel AISI 304 with 26" - 36" VR-71A
RF; carbon steel; metal-metal (over 200°C).
flexible-graphite, with inner ring
JE-06 26" - 36" AISI 304 Check valve; globe; with damping piston;
VR-78
2" - 24" class 150; FLG; RF; Viton TBR-S seat (up to
Stud ASTM A 320 Gr L7 (Note 4)
PAE-07 200°C).
1/2" - 1 "
(Note 2)
Nut ASTM A 194 Gr 4/S3 Other
Stud PAE-08 1 1/8" - 1 ASTM A 320 Gr L7 Globe valve, needle disc; 3000 PSI; SW;
1/2" - 1 1/2" VAG-21
Nut (Note 2) 1/2" ASTM A 194 Gr 4/S3 carbon steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 12 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 6) Class Standard
Range Allowance
F-Safety System and Flare; G-Glycol; GL-Refrigerated Liquified Petroleum
-46ºC /
ASME B31.3 Gases in Low Temperature; P-Process Hydrocarbon (non-corrosive) (Note
9) .
240ºC
(1,6 mm) 150 B6
Pressure / Temperature Rating
-46 / 38 284
50 278
100 256
110 251
200 200
240 180
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 E
CLIENT: SHEET:
E&P 13 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service (Notes 4 and 5) Class Standard
Range Allowance
ASME B31.3 FW-Fire Water (Aerated Sea Water) 0ºC / 90ºC ___ 150 B7
Pipes and Fittings (Note 2) Valves (Note 7)
Wall (mm)
Size Od Ball
Item Tag or Class Ends Material
(in) (mm)
20 Bar Size Description Tag
1/2" 16 2,0
3/4" 25 2,0
1" 30 2,5
T-90 PLAIN
1 1/4" 38 2,5
Cu-Ni 90/10 (UNS C70620)
1 1/2" 44,5 2,5
EEMUA 144 seamless
2" 57 2,5
18" 457,2 9,5 Gate valve; class 150; FLG; RF; carbon
2" - 12" VG-71
20" 508 11,0 steel, organic coating.
24" 610 13,0 Cu-Ni 90/10 (UNS C70620) Gate valve; class 150; FLG; RF; gear;
T-92 14" - 24" VG-72
28" 711 15,0 EEMUA 144 welded (E=1) carbon steel, organic coating.
32" 813 17,0 Gate valve; class 150; FLG; RF; gear;
26" - 36" VG-72A
36" 914 19,0 carbon steel, organic coating.
Red.Coupling F LREFF-91
1/2" - 2"
Red. Coupling M LREMF-91 M.UCxF.UC Angular valve for hydrant; with adaptor
2 1/2" for hose and cap; max. working pressure VGL-31
Sockolet SKL-91 UC 200 PSIG; threaded; bronze.
Conc. F CONF-91 ___ F.NPTxF.UC
Fem. Niple Con. NIPADF-91 F.NPTxM.UC Check valve; dual plate; wafer; class
2" - 24" VR-108
BP/SPR. NPT BRE-91 M.UCxF.NPT 150; RF; carbon steel; organic coating.
(UNS C70620)
1/2" - 1 1/2"
Backing flange FLG-183 150 BF ASTM A 105 (epoxy coated)
Cu-Ni 90/10
Composite
Weld neck
E&P 14 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Notes 4 and 5) Class Standard
Range Allowance
ASME B31.3 FW-Fire Water (Aerated Sea Water) 0ºC / 90ºC ___ 150 B7
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 290
50 286
75 270
90 258
Branchs Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2 Piping, connections and flanges should be specified according EEMUA 144/145/146.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
5 Use Spec B24 for fixed platform and uninhabited.
6 Isolating joint see drawing on the appendix 15.
7 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 15 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
BR-Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
ASME B31.3
SW-Aerated Sea Water (Naval System) (Note 8)
0ºC / 90ºC ___ 150 B7R
Pipes and Rattings (Note 2) Valves (Note 9)
Wall (mm) or
Size Od Ball
Item Tag Class Ends Material
(in) (mm) 16 Bar Description
Size Tag
1/2" 16 2,0
3/4" 25 2,0
1" 30 2,5
T-90 PLAIN
1 1/4" 38 2,5
Cu-Ni 90/10
1 1/2" 44,5 2,5 (UNS C70620)
EEMUA 144 seamless
2" 57 2,5
18" 457,2 8,0 Gate valve; class 150; FLG; RF; gear;
26" - 36" VG-72A
20" 508 8,5 carbon steel, organic coating.
Fem. Un. Con. UNADF-91 F.UCxF.NPT RF; carbon steel; organic coating.
Male. Un. Con. UNADM-91 M.UCxF.NPT Cu-Ni 90/10 Check valve; dual plate; wafer; class 150;
26" - 36" VR-108A
Male Niple Con. NIPADM-91 M.NPTxM.UC (UNS C70620) RF; carbon steel; organic coating.
1/2" - 1 1/2" Pressure 20 Bar
Fem. Niple Con. NIPADF-91 F.NPTxM.UC (EEMUA 146)
Fittings and Accessories
(UNS C70620)
Weld neck Flange WN (RF) Ni/Al/Br disc; Viton seat.
Cu-Ni 90/10
FLG-94D 6" - 36" 16 Bar
(UNS C70620)
FLG-183 2" - 24"
Backing flange 150 BF ASTM A 105 (epoxy coated)
FLG-185 28" - 36"
Flange
TECHNICAL SPECIFICATION
DR-ENGP-1.1 G
CLIENT: SHEET:
E&P 16 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
BR-Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
ASME B31.3
SW-Aerated Sea Water (Naval System) (Note 8)
0ºC / 90ºC ___ 150 B7R
Pressure / Temperature Rating
TEMPERATURE
DN
up to 38oC 50oC 75oC 90oC
1/2" - 4" 290 psi 286 psi 270 psi 258 psi
6" - 36" 232 psi 232 psi 232 psi 229 psi
Branchs Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2 Piping, connections and flanges should be specified according EEMUA 144/145/146.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
5 Use Spec B24 for fixed platform and uninhabited.
6 Isolating joint see drawing on the appendix 15.
7 For BR, use VB-25, VB-26 and VB-26A.
8 Use only at Naval System, for generators and inert gas seal.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 Use VB-29 and VB-29A, flanged only at sea chest.
11 Diaphragm valve should be used according Project Engineer.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 17 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
DFC-Closed Drain (Corrosive Hydrocarbon); PC-Process (Corrosive Hydrocarbon) (Notes
0ºC / 240ºC
ASME B31.3 6, 10 and 17); PCW-Produced water (Note 6); DA-Open Drain (Notes 9, 12 and 15);
AM-Amine (Note 14); SP-Vent and tank sounding; F-Safety system and Flare
(Note 17)
(3,2 mm) 150 B9
Pipes and Fittings Valves (Notes 9 and 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2" - 3/4" XXS API 5L Gr B PSL 1 Size Description Tag
T-05A PLAIN
1" - 1 1/2" seamless
Ball valve; class 800; SW; carbon steel,
Sch 80 1/2" - 3/4" VE-333D
2" - 3" API 5L Gr B PSL 1 RPTFE® seat; up to 150ºC.
seamless or welded
T-02A/T-02B 4" - 6" Sch 40 Ball valve; class 800; SW; carbon steel,
ERW or ERW / HFIW 1" - 1 1/2" VE-333B
8" - 10" Sch 20 (E=0,85) (Note 18) RPTFE® seat; up to 150ºC.
Pipe 12" Sch 30 Ball valve; class 150; FLG; RF; carbon VE-334
2" - 4"
14" - 20" Sch 20 BW steel, RPTFE® seat; up to 150ºC. VE-335
Red. Tee TRE-03 1/2" - 1 1/2" Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-305B
Cross CRUZ-06 PEEK® seat; up to 220°C.
6000
Half Coupling ML-03 Ball valve; class 150; FLG; RF; carbon VE-306
2" - 4"
Red. Coupling LRE-02 steel, PEEK® seat; up to 220°C. VE-307
1/2" - 3/4"
Cap TAM-06 Ball valve; class 150; FLG; RF; gear;
6" - 24" VE-308
Union UN-05 carbon steel, PEEK® seat; up to 220°C.
Elbow 45º JO-08 Ball valve; class 800; SW; carbon steel,
1/2" - 3/4" VE-48D
Equal Tee TE-05 over 220°C.
Red. Tee TRE-02 Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-48B
Cross CRUZ-05 over 220°C.
1" - 1 1/2" 3000
Half Coupling ML-02 Ball valve; class 150; FLG; RF; carbon VE-50
2" - 4"
Red. Coupling LRE-01 steel, over 220°C. VE-67
Red .Nip.E NIPRE-10 Ball valve; fire tested; class 800; SW;
1" - 1 1/2" carbon steel; RPTFE® seat; up to VE-337B
Red.Nip.C NIPRC-04A 150°C.
1/2" - 4"
Red .Nip.E NIPRE-10A BW/PLAIN Ball valve; fire tested; class 150; FLG; VE-338
2" - 4" RF; carbon steel; RPTFE® seat,up to
S.R.ELL 90º CRC-01 2" - 24" 150°C. VE-339
S.R.ELL 90º CRL-01 Wall thickness Ball valve; fire tested; class 150; FLG;
according to pipe 6" - 24" RF; gear; carbon steel; RPTFE® seat; VE-340
S.R.ELL 45º CRL-02 ASTM A 234 Gr WPB
up to 150°C.
Tee TE-02 Ball valve; fire tested; class 150; FLG;
26" - 36" RF; gear; carbon steel; RPTFE® seat; VE-340A
Red. Tee TRE-01 up to 150°C.
Conc. Red. REDC-01 2" - 36" BW Ball valve; fire tested; class 800; SW;
1/2" - 3/4" VE-309D
Ecc. Red. REDE-02 carbon steel, PEEK® seat.
Weldolet WOL-01 ASTM A 105 Ball valve; fire tested; class 150; FLG; VE-310
2" - 4"
RF; carbon steel, PEEK® seat. VE-311
Gate (Note 5)
FLG-05E 1/2" - 1 1/2" SW (RF) Gate valve; class 150; FLG; RF; gear;
14" - 24" VG-04
FLG-05A 1/2" - 24" BLIND (RF) carbon steel.
Flange
FLG-04A 1" - 24" 150 WN (RF) ASTM A 105 Gate valve; class 150; FLG; RF; gear;
(Note 8) 26" - 36" VG-04A
FLG-05C BLIND (RF) carbon steel.
26" - 36"
FLG-04C WN (RF) Globe
JPH-07 1/2" - 10" 1/16" (1,6mm) Compressed non-asbestos (aramida Globe valve; class 150; FLG; RF; carbon
2" - 10" VGL-03
JPH-08 12" - 36" fiber and NBR) steel.
1/8" (3,2mm)
JI-01 1/2" - 36" Fenolic resin with neoprene Check
Gasket
RF Stainless steel AISI 304 with flexible- Check valve; horizontal piston; class
(Notes 10 and 11) JE-04 1/2" - 6" 1/2" - 1 1/2" VR-150
graphite 800; SW; carbon steel.
0,175" (4,4mm)
JE-05 8" - 24" Check valve; dual plate; wafer; class
Stainless steel AISI 304 with flexible-
2" - 24" 150; RF; carbon steel; Viton TBR-S seat VR-35
JE-06 26" - 36" graphite, with inner ring AISI 304
(up to 200ºC).
Check valve; dual plate; wafer; class
26" - 36" 150; RF; carbon steel; Viton TBR-S seat VR-35A
Stud PAE-01 ASTM A 193 Gr B7 (up to 200ºC).
1/2" - 1"
Nut (Note 2) ASTM A 194 Gr 2H Check valve; dual plate; wafer; class
2" - 24" 150; RF; carbon steel; metal-metal VR-28
Stud PAE-02 ASTM A 193 Gr B7 (over 200ºC).
1 1/8" -1 1/2"
Nut (Note 2) ASTM A 194 Gr 2H Check valve; dual plate; wafer; class
26" - 36" 150; RF; carbon steel; metal-metal VR-28A
Stud PAE-09 ASTM A 193 Gr B16 (over 200ºC).
1/2" - 1"
Nut (Note 2 and 4) ASTM A 194 Gr 7 Other
Stud PAE-10 ASTM A 193 Gr B16 Globe valve, needle disc; 3000 PSI; SW;
1 1/8" -1 1/2" 1/2" - 1 1/2" VAG-17
Nut (Note 2 and 4) ASTM A 194 Gr 7 carbon steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 18 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
DFC-Closed Drain (Corrosive Hydrocarbon); PC-Process (Corrosive Hydrocarbon) (Notes
0ºC / 240ºC
ASME B31.3 6 , 10 and 17); PCW-Produced water (Note 6); DA-Open Drain (Notes 9, 12 and 15);
AM-Amine (Note 14); SP-Vent and tank sounding; F-Safety system and Flare
(Note 17)
(3,2 mm) 150 B9
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
50 278
100 256
110 251
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM A194 GR
7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges ≤ 1 1/2" may be used, if strictly necessary.
9 When Classifier especifies metallic material, this Spec must be used and valves shall be according to Spec B22 (FRP).
10 For temperatures ranging from 110ºC up to 240ºC, in PC service, use Spiral-Wound Gasket.
11 Isolating joint see drawing on the appendix 15.
12 When Naval Systems use only Spec B9.
13 When requerid Fully Tight valve (VET), see types in appendix 14.
14 For use condensate from K.O. drum to Amine flash drum.
15 On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
16 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
17 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
18 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 19 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE SYSTEM
Temp.
CODE Service Corrosion Allowance Class Standard
Range
G-Glicol; F-Safety System and Flare; D-Diesel (Note 10); FL-Foam Line (Note 12); DF-Closed
Drain (Non-Corrosive hydrocarbon); BG-Inert Gas; SN-Start-up Nitrogen; SA-Service
Compressed Air (Utility Air); FG-Fuel Gas (Note 11); IW-Fresh And De-Aerated Sea Water 0ºC / 240ºC
ASME B31.3 Injection (Note 9); CHW-Chilled Water (VAC) (Note 14); CI-Chemical Injection (non-
corrosive); W-Industrial Water (Fresh, Non-corrosive/De-Aerated Sea Water) (Note 14); OL-
(Notes 13 and
20)
(1,6 mm) 150 B10
Lubrication Oil; P-Process (non-corrosive hydrocarbon) (Naval System) (Notes 9, 16 and 21);
AM-Amine (Note 19).
T-05A PLAIN Ball valve; class 800; SW; carbon steel, RPTFE® seat, up
1" - 1 1/2" VE-333B
to 150ºC.
1" - 1 1/2" Sch 80 Ball valve; class 150; FLG; RF; carbon steel, RPTFE® VE-334
API 5L Gr B PSL 1 2" - 4"
seat, up to 150ºC. VE-335
seamless
Ball valve; class 150; FLG; RF; gear; carbon steel,
2" - 3" Sch 80 6" - 24" VE-336
RPTFE® seat, up to 150ºC.
2" - 3" Sch 80 Ball valve; class 800; SW; carbon steel, PEEK® seat, up
1" - 1 1/2" VE-305B
4" - 6" Sch 40 to 220°C.
BW
8" - 10" Ball valve; class 150; FLG; RF; carbon steel, PEEK® seat, VE-306
Sch 20 2" - 4"
12" API 5L Gr B PSL 1 up to 220°C. VE-307
welded
T-02B 14" - 18" Sch 10 ERW or ERW / HFIW Ball valve; class 150; FLG; RF; gear; carbon steel, PEEK®
6" - 24" VE-308
20" - 24" Sch 20 (E=0,85) seat, up to 220°C.
(Note 22)
26" - 32" STD Ball valve; class 150; FLG; RF; gear; carbon steel, PEEK®
26" - 36" VE-308A
34" 0,406" seat, up to 220°C.
36" 0,438" 1/2" - 3/4" Ball valve; class 800; SW; carbon steel, over 220ºC. VE-48C
Elbow 90º JO-09 1" - 1 1/2" Ball valve; class 800; SW; carbon steel, over 220ºC. VE-48B
Red. Tee TRE-03 1/2" - 1 1/2" Ball valve; class 150; FLG; RF; gear; carbon steel, over
6" - 24" VE-68
Cross CRUZ-06 220ºC.
6000
Half Coupling ML-03 Ball valve; class 150; FLG; RF; gear; carbon steel, over
26" - 36" VE-68A
Red. Coupling LRE-02 220ºC.
1/2" - 3/4" Ball valve; fire tested; class 800; SW; carbon steel,
Cap TAM-06 1/2" - 3/4" VE-342C
RPTFE®/metallic seat.
Ball valve; fire tested; class 800; SW; carbon steel,
Union UN-05 1" - 1 1/2" VE-337B
RPTFE®/metallic seat.
(Notes 1 and 18)
Coupling L-05 Ball valve; fire tested; class 150; FLG; RF; carbon steel, VE-338
SW ASTM A 105 2" - 4"
Elbow 90º JO-07 RPTFE®/metallic seat. VE-339
Elbow 45º JO-08 Ball valve; fire tested; class 150; FLG; RF; gear; carbon
6" - 24" VE-340
Equal Tee TE-05 steel, RPTFE®/metallic seat.
Red. Tee TRE-02 Ball valve; fire tested; class 150; FLG; RF; gear; carbon
26" - 36" VE-340A
Cross CRUZ-05 steel, RPTFE®/metallic seat.
1" - 1 1/2" 3000 Ball valve; fire tested; class 800; SW; carbon steel,
Half Coupling ML-02 1/2" - 3/4" VE-317C
PEEK®/metallic seat.
Fittings and Accessories
Coupling L-04 Ball valve; fire tested; class 150; FLG; RF; gear; carbon
6" - 24" VE-312
Short Nip. steel, PEEK®/metallic seat.
T-05A API 5L Gr B PSL 1
Long Nip. Ball valve; fire tested; class 150; FLG; RF; gear; carbon
1/2" - 1 1/2" PLAIN 26" - 36" VE-312A
Red.Nip.C NIPRC-04 steel, PEEK®/metallic seat.
S.R.ELL 90º CRC-01 2" - 24" 2" - 12" Gate valve; class 150; FLG; RF; carbon steel. VG-114
L.R.ELL90º CRL-01 14" - 24" Gate valve; class 150; FLG; RF; gear; carbon steel. VG-04
Wall thickness
according to pipe ASTM A 234 Gr WPB Gate valve; class 150; FLG; RF; gear; carbon steel.
L.R.ELL 45º CRL-02 26" - 36" VG-04A
Weldolet WOL-01 ASTM A 105 Check valve; dual plate; wafer; class 150; RF; carbon
2" - 24" VR-28
FLG-05E 1/2" - 1 1/2" SW (RF) steel; metal-metal (over 200ºC).
FLG-05A 1/2" - 24" BLIND (RF) Check valve; dual plate; wafer; class 150; RF; carbon
Flange 26" - 36" VR-35A
(Notes 6, 8 and FLG-04A 1" - 24" 150 WN (RF) ASTM A 105 steel; Viton TRB-S seat,up to 200ºC.
18) FLG-05C BLIND (RF) Check valve; dual plate; wafer; class 150; RF; carbon
26" - 36" 26" - 36" VR-28A
FLG-04C WN (RF) steel; metal-metal (over 200ºC).
JI-01 1/2" - 36" 1/8" (3,2mm) Fenolic resin with neoprene Butterfly valve; flanged; max. pressure 150 PSIG; RF;
26" - 36" VB-12A
Stud ASTM A 193 Gr B7 gear; ductile iron, Nylon 11 coated disc, Viton seat.
PAE-01
1/2" - 1"
Nut (Note 2) ASTM A 194 Gr 2H
Butterfly valve; wafer; max. pressure 250 PSIG; ductile
2" - 6" VB-18
iron, Nylon 11 coated disc, Viton seat.
Stud PAE-02
ASTM A 193 Gr B7
1 1/8" -1 1/2"
(Note 2)
Nut ASTM A 194 Gr 2H
Butterfly valve; wafer; max. pressure 250 PSIG; gear;
8" - 24" VB-19
ductile iron, Nylon 11 coated disc, Viton seat.
Stud PAE-09 ASTM A 193 Gr B16
1/2" - 1"
(Note 2 and 4)
Nut ASTM A 194 Gr 7 Butterfly valve; flanged; max. pressure 250 PSIG; RF;
26" - 36" VB-19A
Stud ASTM A 193 Gr B16 gear; ductile iron, Nylon 11 coated disc, Viton seat.
PAE-10
1 1/8" -1 1/2"
Nut (Note 2 and 4) ASTM A 194 Gr 7 Butterfly valve; wafer; max. pressure 150 PSIG; ductile
2" - 10" VB-14
iron, AISI 316 disc, Viton seat.
Other
1/2" – 1 1/2" Globe valve, needle disc; 3000 PSI; SW; carbon steel. VAG-17
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 K
CLIENT: SHEET:
E&P 20 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp.
CODE Service Range
Corrosion Allowance Class Standard
G-Glicol; F-Safety System and Flare; D-Diesel (Note 10); FL-Foam Line (Note 12); DF-Closed
Drain (Non-Corrosive hydrocarbon); BG-Inert Gas; SN-Start-up Nitrogen; SA-Service
Compressed Air (Utility Air); FG-Combustible Gas (Note 11); IW-Fresh And De-Aerated Sea 0ºC / 240ºC
ASME B31.3 Water Injection (Note 9); CHW-Chilled Water (VAC) (Note 14); CI-Chemical Injection (non-
corrosive); W-Industrial Water (Fresh, Non-corrosive/De-Aerated Sea Water) (Note 14); OL-
(Notes 13 and
20)
(1,6 mm) 150 B10
Lubrication Oil; P-Process (non-corrosive hydrocarbon) (Naval System) (Notes 9 , 16 and 21);
AM-Amine (Note 19).
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
50 278
100 256
110 258
200 200
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM A194 GR 7 nuts
for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 On offshore facilities the slip-on flanges use shall be restricted to flare lines only, according to API 14E - item 4.5(2)-Use FLG-03A e FLG-03B.
7 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges ≤ 1 1/2" may be used, if strictly necessary.
9 Butterfly valves, instead of ball valves, should be used for work in IW and P (cargo line).
10 Use only upstream centrifuge.
11 Use only upstream filtres.
12 Only in onshore facilities use this Spec for FL service (foam line).
13 For temperatures ranging from 110ºC up to 240ºC, in P and F services, use Spiral-Wound Gasket
14 When Classifier especifies metallic material.
15 Isolating joint see drawing on the appendix 15.
16 On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
17 When requerid Fully Tight Valve (VET), see types in appendix 14.
18 For onshore instalation use DN 2" and 3" SCH-40.
19 For use outlet of Amine stripper to booster pump suction.
20 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
21 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
22 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 21 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
PCW-Produced water (Nota 6); PC-Process (Note 13); 0ºC / 150ºC
ASME B31.3 ADW-Aerated Dilution Water (Desalinated and Aerated Sea Water); IW -
Fresh and De-aerated Sea Water Injection.
(Notes 8 and
14)
___ 150 B11
Pipes and Fittings (Organic coating - according appendix 18) Valves (Organic coating - according appendix 18) (Note 10)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
T-05A 1" - 1 1/2" PLAIN Size Description Tag
Sch 80
2" - 3" API 5L Gr B PSL 1 Ball valve; class 150; FLG; RF; carbon
1" - 1 1/2" VE-346B
T-02A 4" - 6" Sch 40 seamless steel; RPTFE® seat; organic coating.
8" - 10" Sch 20 Ball valve; class 150; FLG; RF; carbon VE-347
2" - 4"
2" - 3" Sch 80 steel; RPTFE® seat; organic coating. VE- 348
Pipe Ball valve; class 150; FLG; RF; gear;
4" - 6" Sch 40
(Note 12) BW 6" - 24" carbon steel; RPTFE® seat; organic VE-349
8" - 10" coating.
Sch 20 API 5L Gr B PSL 1
T-02B 12" welded ERW or ERW / HFIW Ball valve; class 150; FLG; RF; gear;
(E=0,85) (Note 15) 26 - 28" carbon steel; RPTFE® seat; organic VE-349A
14" - 18" Sch 10 coating.
20" - 24" Sch 20 Ball valve; fire tested; class 150; FLG;
1" - 1 1/2" RF; carbon steel; RPTFE®/metallic seat, VE-350B
26" - 28" STD organic coating.
Elbow 90º JO-07 Ball valve; fire tested; class 150; FLG; VE-351
2" - 4" RF; carbon steel; RPTFE®/metallic seat,
Elbow 45º JO-08 organic coating. VE-352
Equal Tee TE-05 Ball valve; fire tested; class 150; FLG;
6" - 24" RF; gear; carbon steel; RPTFE®/metallic VE-353
Red. Tee TRE-02 seat, organic coating.
Cross CRUZ-05 Ball valve;fire tested; class 150; FLG; RF;
1" - 1 1/2" 3000 SW ASTM A 105 26 - 28" gear; carbon steel; RPTFE®/metallic seat; VE-353A
Half Coupling ML-02 organic coating.
(Notes 1 and 7)
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
T-05A
Long Nip.
Fittings and Accessories
Cap TAM-02
Cross CRUZ-02
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 22 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
PCW-Produced water; PC-Process (Note 13); 0ºC / 150ºC
ASME B31.3 ADW-Aerated Dilution Water (Desalinated and Aerated Sea Water);SW
(Sea Water).
(Notes 8 and
14)
___ 150 B11
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
50 278
100 256
110 258
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
8 For temperatures ranging from 110ºC up to 170ºC use Spiral-Wound Gasket.
9 Isolating joint see drawing on the appendix 15.
10 When required Fully Tight Valve (VET), see types in appendix 14.
11 All piping shall be internal organic coated according Appendix 18.
12 For onshore instalation use DN 2" and 3" SCH 40.
13 Use this service only after a review of corrosivity.
14 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
15 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 23 of 192
TECHNICAL SPECIFICATION ET-200.03
TÍTULO: PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 140ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 5 and 13)
(Note 13)
____ 150 B12
Pipes and Fittings (Note 7) Valves (Notes 8 and 9)
Size Wall or
Item Tag Ends Material Ball
(in) class
T-17 1/2" - 1 1/2" Sch 40S PLAIN Size Description Tag
ASTM A 790 (UNS S32760)
seamless Ball valve; class 800; SW; superduplex
T-19 2" - 8" 1/2" - 1 1/2" VE-354
Sch 10S stainless steel, RPTFE® seat, up to 150°C.
Pipe 10" - 24" Ball valve; class 150; FLG; RF; superduplex
BW 2" - 4" VE-355
26" - 28" Sch 10 ASTM A 928 (UNS S32760 class 1 or stainless steel, RPTFE® seat, up to 150°C.
T-49 3)
30" Sch 10S Ball valve; class 150; FLG; RF; gear;
welded (E=1)
6" - 24" superduplex stainless steel, RPTFE® seat, up VE-356
32" - 36" Sch 10 to 150°C.
Elbow 90º JO-29 Ball valve; class 150; FLG; RF; gear;
26" - 36" superduplex stainless steel, RPTFE® seat, up VE-356A
Elbow 45º JO-30 to 150°C.
Equal Tee TE-18 Ball valve; fire tested, class 800; SW;
1/2" - 1 1/2" VE-364
Red. Tee TRE-13 superduplex stainless steel.
Cross CRUZ-18
(Notes 1 and 3)
ASTM A 182 Gr F 55 Ball valve; fire tested, class 150; FLG; RF;
3000 SW 2" - 4" VE-365
Half Coupling ML-12 (UNS S32760) superduplex stainless steel.
Red. Coupling LRE-08 Ball valve; fire tested, class 150; FLG; RF;
1/2" - 1 1/2" 6" - 24" VE-366
Cap TAM-22 gear; superduplex stainless steel.
Union UN-15 Ball valve; fire tested, class 150; FLG; RF;
26" - 36" VE-366A
Coupling L-16 gear; superduplex stainless steel.
PLAIN
Red.Nip.C NIPRC-09 Gate (Note 2)
Red.Nip.E NIPRE-15 Gate valve; class 800; SW; superduplex
1/2" - 1 1/2" VG-51
Red.Nip.C NIPRC-09A stainless steel.
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-15A Gate valve; class 150; FLG; RF; superduplex
2" - 12" VG-55
S.R.ELL 90º CRC-06 2" - 24" stainless steel.
L.R.ELL 90º CRL-13 Wall Gate valve; class 150; FLG; RF; gear;
thickness 14" - 24" VG-56
L.R.ELL 45º CRL-14 ASTM A 815 (UNS S32760) superduplex stainless steel.
according to
Tee TE-25 pipe Gate valve; class 150; FLG; RF; gear;
26" - 36" VG-56A
Red. Tee TRE-19 superduplex stainless steel.
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 24 of 192
TECHNICAL SPECIFICATION ET-200.03
TÍTULO: PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 140ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 5 and 13)
(Note 13)
____ 150 B12
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
50 282
100 256
110 251
120 245
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-44) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 According appendix 16 - Welding qualification requirements for superduplex.
7 Isolating joint see drawing on the appendix 15.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves superduplex.
10 For temperature over 110ºC, use spiral gaskets.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 25 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
This Spec shall de used only for repair, when the plant was designed
0ºC / 120ºC
ASME B31.3 usine pipes and fittings according with (UNS S32750). For new projects _______ 150 B13
use B12 (UNS S32760).
Pipes and Fittings (Note 6) Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-13 1/2" - 1 1/2" Sch 40S PLAIN Size Description Tag
ASTM A 790 (UNS S32750)
seamless Ball valve; class 800; SW; superduplex
T-15 2" - 8" 1/2" - 1 1/2" VE-74
Pipe stainless steel.
Sch 10S BW ASTM A 928 (UNS S32750 class 1
Ball valve; class 150; FLG; RF;
T-48 10" - 24" or 3) 2" - 4" VE-76
superduplex stainless steel.
welded (E=1)
Elbow 90º JO-27 Ball valve; class 150; FLG; RF; gear;
6" - 24" VE-77
Elbow 45º JO-28 superduplex stainless steel.
Union UN-14
Coupling L-15
PLAIN
Red. Nip. C NIPRC-08 Gate (Note 2)
Red. Nip. E NIPRE-14 Gate valve; class 800; SW; superduplex
1/2" - 1 1/2" VG-50
Red. Nip. C NIPRC-08A stainless steel.
1/2" - 4" BW/PLAIN
Red. Nip. E NIPRE-14A Gate valve; class 150; FLG; RF;
2" - 12" VG-55
S.R.ELL 90º CRC-05 superduplex stainless steel.
L.R.ELL 90º CRL-11 Wall Gate valve; class 150; FLG; RF; gear;
thickness 14" - 24" VG-56
L.R.ELL 45º CRL-12 ASTM A 815 (UNS S32750) superduplex stainless steel.
according to
Tee TE-24 pipe
Cross CRUZ-20
ASTM A 182 Gr F 53
Weldolet WOL-06
(UNS S32750)
Check
Check valve; horizontal; piston type;
1/2" - 1 1/2" class 800; SW; superduplex stainless VR-86
steel.
Check valve; dual plate; wafer; class
2" - 24" 150; RF; superduplex stainless steel.; VR-72
Viton seat TBR-S
FLG-68 1/2" - 1 1/2" SW (RF) Other
Flange ASTM A 182 Gr F 53
FLG-67 1/2" - 24" 150 BLIND (RF) Globe valve; needle disc; 3000 PSIG;
(Note 4) (UNS S32750) 1/2" - 1 1/2" VAG-29
FLG-66 2" - 24" WN (RF) SW; stainless steel superduplex.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 D
CLIENT: SHEET:
E&P 26 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
This Spec shall de used only for repair, when the plant was designed
0ºC / 120ºC
ASME B31.3 usine pipes and fittings according with (UNS S32750). For new projects
use B12 (UNS S32760).
_______ 150 B13
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
50 282
100 256
110 251
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-45) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Isolating joint see drawing on the appendix 15.
6 According appendix 16 - Welding qualification requirements for superduplex.
7 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 27 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
Temp.
CODE Service Allowance Class Standard
Range
(Note 14)
BW-Ballast (Notes 3 and 11); CN-Sodium Hypoclorite (Note 8); IW-Fresh
ASME B31.3 and De-Aerated Sea Water Injection (Note 2); IWC-Aerated sea water
injection (Note 3); SW-Aerated Sea Water (Notes 3 and 12)
0ºC / 70ºC _____ 150 B14
Pipes and Fittings (Coated with polyethylene - according to appendix 13) Valves (Note 13)
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 1" - 1 1/2" Sch 80 PLAIN API 5L Gr B PSL 1 seamless Size Description Tag
2" - 6" Sch 40 Ball valve; class 150; FLG; FF; carbon
T-02A 1" - 1 1/2" VE-44
8" - 10" Sch 20 API 5L Gr B PSL 1 steel.
seamless or
2" - 6" Sch 40 welded (E=0,85) Ball valve; class 150; FLG; FF; carbon VE-10E
2" - 4"
8" - 10" steel. VE-17E
Sch 20
12" Ball valve; class 150; FLG; FF; gear;
6" - 24" VE-22E
14" - 18" Sch 10 carbon steel.
Pipe
20" - 24" Sch 20 Ball valve; class 150; FLG; FF; gear;
(Note 9) BW 26" - 44" VE-22F
26" - 32" STD carbon steel.
T-02B
34" 0,406" API 5L Gr B PSL 1
36" 0,438" welded (E=0,85)
Tee TE-05
Cross CRUZ-05
3000 SW ASTM A 105
Fittings and Accessories (Notes 1, 5 and 9)
Union UN-04
Coupling L-04
Short Nip. API 5L Gr B PSL 1 Butterfly
T-05A Butterfly valve; wafer; max. pressure
Long Nip. seamless
PLAIN 2" - 10 150 psig; ductile iron, Nylon 11 VB-37
Red. Nip. C NIPRC-04 coated disc, Viton seat.
Butterfly valve; wafer; max. pressure
Red. Nip. E NIPRE-10
12" - 24" 150 psig; gear; ductile iron, Nylon 11 VB-38
Red. Nip. C NIPRC-04A coated disc, Viton seat.
1" - 4" BW/PLAIN Butterfly valve; flanged; max.
Red. Nip. E NIPRE-10A
26" - 36 pressure 150 psig; FF; gear; ductile VB-13A
S.R.ELL 90º CRC-01 2" - 24"
iron, Nylon 11 coated disc, Viton seat.
L.R.ELL 90º CRL-01 Wall Butterfly valve; wafer; max. pressure
thickness 2" - 6" 250 psig; ductile iron, Nylon 11 VB-35
L.R.ELL 45º CRL-02 ASTM A 234 Gr WPB coated disc, Viton seat.
according to
Tee TE-02 pipe Butterfly valve; wafer; max. pressure
8" - 24" 250 psig; gear; ductile iron, Nylon 11 VB-36
Red. Tee TRE-01 coated disc, Viton seat.
BW
Conc. Red. REDC-01 2" - 44" Butterfly valve; flanged; max.
26" - 44" pressure 250 psig; FF; gear; ductile VB-20A
Ecc. Red. REDE-01 iron, Nylon 11 coated disc, Viton seat.
Cap TAM-02 Check
Cross CRUZ-02 Check valve; horizontal; piston type;
1" - 1 1/2" VR-92
Weldolet WOL-01 class 800; FLG; FF; carbon steel.
FLG-04B 1" - 1 1/2" WN (FF) Check valve; dual plate; wafer; class
2" - 24" 150; FF; carbon steel; Viton seat; VR-148
FLG-05B BLIND (FF) organic coated.
FLG-04B 1" - 24" WN (FF) ASTM A 105 Check valve; dual plate; wafer; class
Flange
150 26" - 44" 150; FF; carbon steel; Viton seat; VR-148A
(Note 6) FLG-02A SO (FF) organic coated.
FLG-05D BLIND (FF)
26" - 44"
FLG-04D WN (FF)
Stud PAE-02
ASTM A 193 Gr B7
1 1/8" - 1 1/4"
(Note 7)
Nut ASTM A 194 Gr 2H
Stud PAE-09
ASTM A 193 Gr B7
1/2" - 1 "
(Note 7)
Nut ASTM A 194 Gr 7
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 28 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Corrosion
Temp.
CODE Service Allowance Class Standard
Range
(14)
BW-Ballast (Notes 3 and 11); CN-Sodium Hypoclorite (Note 8); IW-Fresh
ASME B31.3 and De-Aerated Sea Water Injection (Note 2); IWC-Aerated sea water
injection (Note 3); SW-Aerated Sea Water (Notes 3 and 12)
0ºC / 70ºC _____ 150 B14
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38º 284
50 278
70 269
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
3 When Classifier especifies metallic material, this Spec must be used and valves shall be according to Spec B22 (FRP).
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
8 For CN service where the classifier does not allow PVC (B20) and requires metal material, use B14 pipes and connections and B20
valves.
9 All piping must be polyetilen internally coated, according to appendix 13.
10 Isolating joint see drawing on the appendix 15.
11 BW-ballast, for Naval Systems, use Spec B15.
12 At Naval System, use in main deck distribution.
13 When required Fully Tight Valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 29 of 192
TTTLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service (Note 4) Class Standard
Range Allowance
BW-Ballast (Note 4); P-Load line (Naval System); PCW-Produced Water (Note 4); C-
ASME B31.3 Load System (Auxiliary/Main) (Note 6); PC-Slop Unloading System (Naval System) (Note 10ºC / 110ºC (1,6 mm) 150 B15
10); SWW-Aereated Sea Flushing Water (Naval System).
Pipe and Fittings
Valves (Note 8)
Pipe
Size
Item Tag End Material
(in) OD (mm) Wall Ball (Note 5)
T-05A 1/2" - 1 1/2" - Sch 160 PLAIN API 5L Gr B PSL 1 Size Description Tag
8" 219.1 13 mm
10" 273.0 13 mm
12" 323.8 13 mm
14" 355.6 13 mm
22" 558.8 15 mm
30" 762.0 19 mm
32" 812.8 19 mm
Equal Tee TE-06 Check valve, dual plate; wafer, class 150, RF,
2" - 24" VR-149
Red. Tee TRE-03 carbon steel, Viton seat; organic coated.
Cross CRUZ-06 Check valve, dual plate; wafer, class 150, RF,
6000 SW ASTM A 105 26" - 36" VR-149A
Half Coupling ML-03 carbon steel, Viton seat; organic coated.
1/2" - 1 1/2"
Red. Coupling LRE-02 Butterfly (Note 7)
Cap TAM-06 Butterfly valve; wafer; max. pressure 150
2" - 10" VB-14
Union UN-05 PSIG; ductile iron, AISI 316 disc, Viton seat.
THE DATA OR PART THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMITION
N: REV:
E&P 30 of 192
TECHNICAL SPECIFICATION ET-200.03
TTTLE: PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service (Note 4) Class Standard
Range Allowance
BW-Ballast (Note 4); P-Load line (Naval System); PCW-Produced Water (Note 4); C-
ASME B31.3 Load System (Auxiliary/Main) (Note 6); PC-Slop Unloading System (Naval System) (Note 10ºC / 110ºC
10); SWW-Aereated Sea Flushing Water (Naval System).
(1,6 mm) 150 B15
up to 38 284
50 278
100 256
110 251
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Isolating joint see drawing on the appendix 15.
4 Use only for Naval Systems.
5 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7 nuts
for this valves assembly shall be Zn-Ni coated.
6 Use Spec B10 for drop line of Naval Systems.
7 Use at sea chest, VB-23, VB-24 and VB-24A.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 Use niple THD X Plain and threaded cap (TAM-15) after drains and vents blocking
10 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
THE DATA OR PART THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMITION
N: REV:
E&P 31 of 192
Corrosion
CODE Service Temp. Range Class Standard
Allowance
AM-Amine (Note 11); PC-Process (Corrosive Hydrocarbon) (Note 13); F- -46ºC / 130ºC
ASME B31.3
Safety System and Flare (Note 10)
____ 150 B16
Pipes and Fittings Valves (Notes 8 and 9)
Size
Item Tag Wall or class Ends Material Ball
(in)
1/2" Sch 40S STD 0,109" Size Description Tag
3/4" Sch 40S STD 0,113" Ball valve; class 800; SW; duplex steel,
T-36 PLAIN 1/2" - 1 1/2" VE-209
1" Sch 40S STD 0,133" RPTFE® seat.
1 1/2" Sch 40S STD 0,145" ASTM A 790 (UNS S31803) Ball valve; class 150; FLG; RF; duplex steel,
2" - 4" VE-210
2" Sch 10S STD 0,109" seamless RPTFE® seat.
3" - 4" Sch 10S 0,120" Ball valve; class 150; FLG; RF; gear; duplex
T-37A 6" - 24" VE-211
6" Sch 10S 0,134" steel, RPTFE® seat.
Pipe
8" Sch 10S 0,148" Ball valve; class 150; FLG; RF; gear; duplex
26" - 28" VE-211A
10" - 24" Sch 10S 0,165" steel, RPTFE® seat.
BW
12" Sch 10S 0,180" Ball valve; class 800; SW; duplex steel;
1/2" - 1 1/2" VE-387
14" - 18" Sch 10S 0,188" ASTM A 928 (UNS S31803 class 1 TFE/P® seat.
T-47 or 3)
20" Sch 10S 0,218" welded (E=1) Ball valve; class 150; FLG; RF; duplex steel;
2" - 4" VE-388
24" Sch 10S 0,250" TFE/P® seat.
26" - 28" Sch 10 0,312" Ball valve; class 150; FLG; RF; gear; duplex
6" - 24" VE-389
Elbow 90º JO-45 steel; TFE/P® seat.
Elbow 45º JO-46 Ball valve; class 150; FLG; RF; gear; duplex
26" - 28" VE-389A
Equal Tee TE-38 steel; TFE/P® seat.
Red. Tee TRE-33 Ball valve; fire tested; class 800; SW; duplex
1/2" - 1 1/2" VE-212
Cross CRUZ-32 steel; RTPFE®/metallic seat.
(Notes 1 and 3)
ASTM A 182 Gr F 51
3000 SW
Half Coupling ML-18 (UNS S31803)
Ball valve; fire tested; class 150; FLG; RF;
2" - 4" VE-213
Red. Coupling LRE-16 duplex steel; RTPFE®/metallic seat.
1/2" - 1 1/2"
Cap TAM-35 Ball valve; fire tested; class 150; FLG; RF;
6" - 24" VE-214
Union UN-23 gear; duplex steel; RTPFE®/metallic seat.
Coupling L-27 Ball valve; fire tested; class 150; FLG; RF;
26" - 28" VE-214A
Short Nip. gear; duplex steel; RTPFE®/metallic seat.
ASTM A 790 (UNS S31803)
T-36
Long Nip. seamless
Fittings and Accessories
Red.Nip.E NIPRE-18 Ball valve; fire tested; class 150; FLG; RF;
2" - 4" VE-391
Red.Nip.C NIPRC-11A duplex steel; TFE/P®/metallic seat.
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-18A Ball valve; fire tested; class 150; FLG; RF;
6" - 24" VE-392
S.R.ELL 90º CRC-22 2" - 24" gear; duplex steel; TFE/P®/metallic seat.
L.R.ELL 90º CRL-30 Wall Ball valve; fire tested; class 150; FLG; RF;
thickness 26" - 28" VE-392A
L.R.ELL 45º CRL-31 ASTM A 815 (UNS S31803) gear; duplex steel; TFE/P®/metallic seat.
according to
Tee TE-39 pipe
Tampão TAM-36
Cruzeta CRUZ-33
ASTM A 182 Gr F 51
Weldolet WOL-07
(UNS S31803)
Gate (Note 2)
1/2" - 1 1/2" Gate valve; class 800; SW; duplex steel. VG-88
FLG- 120 1/2" - 1 1/2" SW (RF)
JPH-07 1/2" - 10" 1/16" (1,6mm) Compressed non-asbestos Gate valve; class 150; FLG; RF; gear; duplex
26" - 28" VG-90A
JPH-08 12" - 28" 1/8" (3,2mm) (aramida fiber and NBR) steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 32 of 192
Corrosion
CODE Service Temp. Range Class Standard
Allowance
AM-Amine (Note 11); PC-Process (Corrosive Hydrocarbon)(Note 13); F- -46ºC / 130ºC
ASME B31.3
Safety System and Flare (Note 10)
____ 150 B16
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-46 to 38 290
50 282
100 256
110 251
130 240
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According Appendix 16 - welding qualification requirements for duplex and superduplex steel.
8 When required Fully Tight valve (VET) ,see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves duplex and superduplex steel .
10 For temperature over 110ºC, use spiral gaskets.
11 For use Regeneration package inlet.
12 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE 175)
14 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 33 de 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE SYSTEM
Faixa de Tol. de Press. Máx. Trab.
NORMA BÁSICA Serviço Espec.
Temp. Corrosão (PSIG)
0ºC / 120ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 8 and
11)
(6.4 mm) 150 B17
Pipes and Fittings Valves (Note 10)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
API 5L Gr B PSL 1 Size Description Tag
T-05A 3/4" - 1 1/2" XXS PLAIN
seamless
Ball valve; class 800; SW; carbon steel, RPTFE®
3/4" - 1 1/2" VE-333D
seat, up to 150ºC.
2" Sch 80
Ball valve; class 150; FLG; RF; carbon steel, VE-334
2" - 4"
3" Sch 160 RPTFE® seat, up to 150ºC. VE-335
API 5L Gr B PSL 1
4" Sch 80 Ball valve; class 150; FLG; RF; gear; carbon steel,
seamless 6" - 14" VE-336
Pipe T-02A 6" 0,344" BW or RPTFE® seat, up to 150ºC.
API 5L Gr B PSL 1
8" 0,375" Ball valve; fire tested; class 800; SW; carbon
welded (E=0,95) 3/4" - 1 1/2" VE-337D
10" 0,438" steel, RPTFE®/metallic seat.
12" sch 40 0,406" Ball valve; fire tested; class 150; FLG; RF; carbon VE-338
2" - 4"
14' Sch 40 0,438" steel, RPTFE®/metallic seat. VE-339
Cap TAM-33
Red.Nip.C NIPRC-04A
3/4" - 4" Wall BW/PLAIN
Red .Nip.E NIPRE-10A thickness Butterfly
S.R.ELL 90º CRC-01 2" - 14" according to ASTM A 234 Gr WPB
pipe
L.R.ELL 90º CRL-01
Cross CRUZ-02
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 34 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 120ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 8 and
11)
(6,4 mm) 150 B17
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 284
50 278
100 256
110 251
240 180
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7 nuts
for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-54) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 For temperatures ranging from 110ºC up to 240ºC, use Spiral-Wound Gasket
9 Isolating joint see drawing on the appendix 15.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 35 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 6) Class Standard
Range Allowance
-46ºC /
ASME B31.3 F-Safety System and Flare.
310ºC
(3,2 mm) 150 B19
Pipes and Fittings (Note 5) Valves (Note 8)
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" SCH 160 0,188 Size Description Tag
3/4" SCH 160 0,219" Ball valve; class 800; SW; carbon steel,
T-09 PLAIN 1/2" - 3/4" VE-330C
1" SCH 80 XS 0,179" RPTFE® seat, up to 150ºC.
1 1/2" SCH 80 XS 0,200" Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-330B
2" SCH 80 XS 0,218" RPTFE® seat, up to 150ºC.
3" SCH 80 XS 0,300" ASTM A 333 Gr 6 Ball valve; class 150; FLG; RF; carbon steel,
2" - 4" VE-331
4" 0,203" seamless RPTFE® seat, up to 150ºC.
6" 0,219" Ball valve; class 150; FLG; RF; gear; carbon
T-07A 6" - 24" VE-332
steel, RPTFE® seat, up to 150ºC.
Pipe 8" SCH 20 0,250"
10" 0,279" Ball valve; class 150; FLG; RF; gear; carbon
26" - 30" VE-332A
12" 0,281" BW steel, RPTFE® seat, up to 150ºC.
14" SCH 20 0,312" Ball valve; class 800; SW; carbon steel,
1/2" - 3/4" VE-296C
16" - 18" 0,344" PEEK® seat, over 150°C.
20" STD 20 0,375" Ball valve; class 800; SW; carbon steel,
ASTM A 671 Gr CC 60 1" - 1 1/2" VE-296B
T-08 24" - 26" 0,406" PEEK® seat, over 150°C.
CL 22 welded (E=1)
28" 0,438" Ball valve; class 150; FLG; RF; carbon steel,
2" - 4" VE-297
30" 0,469" PEEK® seat, over 150°C.
Elbow 90º JO-17 Ball valve; class 150; FLG; RF; gear; carbon
6" - 24" VE-298
Elbow 45º JO-18 1/2" - 3/4" steel, PEEK® seat, over 150°C.
Equal Tee TE-12 Ball valve; class 150; FLG; RF; gear; carbon
1/2" - 1 26" - 30" VE-298A
Red. Tee TRE-08 steel, PEEK® seat, over 150°C.
1/2"
Cross CRUZ-12 Ball valve; fire tested; class 800; SW;
0,469" 1/2" - 3/4" VE-299C
Half Coupling ML-07 carbon steel, RPTFE® seat, up to 150°C.
Red. Coupling LRE-04 Ball valve; fire tested; class 800; SW;
1/2" 1" - 1 1/2" VE-299B
Cap TAM-12 carbon steel, RPTFE® seat, up to 150°C.
(Notes 1 and 5)
Union UN-09 Ball valve; fire tested; class 150; FLG; RF;
SW ASTM A 350 Gr LF2 CL 1 2" - 4" VE-300
Coupling L-09 carbon steel, RPTFE® seat, up to 150°C.
Elbow 90º JO-13 Ball valve; fire tested; class 150; FLG; RF;
6" - 24" VE-301
Elbow 45º JO-14 gear; carbon steel, RPTFE® seat, up to
Ball valve;fire tested; class 150; FLG; RF;
Equal Tee TE-09
26" - 30" gear; carbon steel, RPTFE® seat, up to VE-301A
Red. Tee TRE-05
150°C.
Cross CRUZ-09 3/4" - 1 Ball valve; fire tested; class 800; SW;
3000 1/2" - 3/4" VE-302C
Half Coupling ML-05 1/2" carbon steel, PEEK® seat, over 150°C.
Red. Coupling LRE-03 Ball valve; fire tested; class 800; SW;
Fittings and Accessories
Union UN-07 Ball valve; fire tested; class 150; FLG; RF;
2" - 4" VE-303
Coupling L-08 carbon steel, PEEK® seat, over 150°C.
Short Nip. ASTM A 333 Gr 6 Ball valve; fire tested; class 150; FLG; RF;
T-09 6" - 24" VE-304
Long Nip. seamless gear; carbon steel, PEEK® seat, over 150°C.
1/2" - 1
Red. Nip. C NIPRC-05 PLAIN
1/2" Ball valve;fire tested; class 150; FLG; RF;
26" - 30" VE-304A
Red. Nip. E NIPRE-16 gear; carbon steel, PEEK® seat, over 150°C.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 36 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 6) Class Standard
Range Allowance
-46ºC /
ASME B31.3 F-Safety System and Flare.
310ºC
(3,2 mm) 150 B19
Pressure / Temperature Rating
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 C
CLIENT: SHEET:
E&P 37 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03 PIPING STANDARD AND MATERIAL FOR OIL
PRODUCTION AND PROCESS FACILITIES AND MARINE SYSTEM
Temp. Corrosion
CODE Service (Note 8) Class Standard
Range Allowance
Globe
Check
Check valve; ball type; max.
1/2" - 4" work pressure 150 psig; sw; VR-89
PVC.
150
FLG-75 SW (FF) PVC
According to
Poly Vynil Chloride
Flange 1/2" - 8" ASME B16.5
ASTM D1784 class 12454
only for
FLG-74 BLIND (FF) Drilling ASME B16.5
dimensions
Needle
Needle valve; 3000 psi;
1/2" - 1 1/2" threaded; male-female; VAG-08
stainless steel.
Teflon enveloped with non-
Gasket JPH-15 1/2" - 8" 1/8" (3,2mm) FF
asbestos insert
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 38 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03 PIPING STANDARD AND MATERIAL FOR OIL
PRODUCTION AND PROCESS FACILITIES AND MARINE SYSTEM
Temp. Corrosion
CODE Service (Note 8) Class Standard
Range Allowance
CHW-Chilled Water (VAC) (Note 4);W-Industrial Water (Fresh, Non-Corrosive/De-
ASME B31.3 aerated Sea Water) (Note 4); GW-Grey Water; PW-Potable Water (Note 5); WW-
Sewage Waste Water; CN-Sodium Hypoclorite (Note 6)
0ºC / 40ºC ______ (Note 7) B20
Pressure / Temperature Rating (Note 7)
TEMPERATURE TEMPERATURE
DN DN
0oC à 23oC 30oC 35oC 40oC 0oC à 23oC 30oC 35oC 40oC
1/2" 848 psi 636 psi 526 psi 424 psi 2 1/2" 425 psi 319 psi 263 psi 212 psi
3/4" 688 psi 516 psi 426 psi 344 psi 3" 375 psi 281 psi 233 psi 188 psi
1" 630 psi 473 psi 391 psi 315 psi 4" 324 psi 243 psi 201 psi 162 psi
1 1/2" 471 psi 353 psi 292 psi 235 psi 6" 279 psi 209 psi 173 psi 140 psi
2" 404 psi 303 psi 251 psi 202 psi 8" 246 psi 185 psi 153 psi 123 psi
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use plan washers to distribute the load of PVC flange.
4 Use spec B10 when Classifier especifies metallic material.
5 Use spec B3 when Classifier especifies metallic material.
6 Use spec B14 when Classifier especifies metallic material.
7 Table according - Pressure / Temperature rating.
8 PVC piping use is restricted to inside living quarter modules, out of risk areas or line not crossing classified bulkhead.
9 For threaded fittings, use 50% of Working Máx. Pressure table above.
10 Shall be used only for isolation of the unit generation of sodium hypoclorite.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 39 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 PWH-Hot Fresh Water (Note 5); HWU-Utility Heading Water (Note 4) 10ºC / 80ºC ______ (Note 6) B21
Pipes and Fittings Valves
Size
Item Tag Wall or Class Ends Material Ball
(in)
Size Description Tag
CPVC
Chlorinated Polyvinyl Chloride Ball valve; class 150; SW;
Pipe T-23 1/2" - 8" Sch 80 PLAIN
ASTM F441 CPVC 4120
1/2" - 8"
CPVC
VE-160
Globe
Check
Check valve; type ball; max.
1/2" - 3" work press. 150 PSIG; sw; VR-88
CPVC
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 40 to 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 PWH-Hot Fresh Water (Note 5); HWU-Utility Heading Water (Note 4) 10ºC / 80ºC ______ (Note 6) B21
Pressure / Temperature Rating (Note 6)
TEMPERATURE TEMPERATURE
DN DN
o o o o o o o o o o
0 C à 27 C 38 C 60 C 80 C 0 C à 27 C 38 C 60 C 80 C
1/2" 848 psi 696 psi 424 psi 212 psi 2 1/2" 425 psi 348 psi 212 psi 106 psi
3/4" 688 psi 564 psi 344 psi 172 psi 3" 375 psi 308 psi 188 psi 94 psi
1" 630 psi 517 psi 315 psi 158 psi 4" 324 psi 266 psi 162 psi 81 psi
1 1/2" 471 psi 386 psi 235 psi 118 psi 6" 279 psi 229 psi 140 psi 70 psi
2" 404 psi 331 psi 202 psi 101 psi 8" 246 psi 202 psi 123 psi 62 psi
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use plan washers to distribute the load of CPVC flange.
4 Use spec A8 when Classifier especifies metallic material.
5 Use spec B3 when Classifier especifies metallic material.
6 Table according - Pressure / Temperature rating.
7 CPVC piping use is restricted to inside living quarter modules, out of risk areas or line not crossing classified bulkhead.
8 For threaded fittings use 50% of Working Máx. Pressure table above.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 41 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service (Notes 16, 17 and 19) Temp. Range Class Standard
Allowance
BW-Ballast (Notes 9, 10 and 11); DA-Open Drain (Note 12); IWC-
ASME B31.3 Aerated Sea Injection Water (Note 9); SW-Aerated Sea Water (Notes 9, 0ºC / 90ºC _____ (Note 13) B22
10 and 11)
d - 4.2.3 (test of long duration) Gate valve; class 150; FLG; FF; gear;
26" - 48" VG-113A
e - 4.3.1.3 (stagnated water) carbon steel; organic coated.
Needle
Gasket JP-01 1" - 48" 1/8" (3,2mm) FF PTFE expanded
Globe valve; 3000 PSIG; threaded;
1/2" - 1 1/2" male/female; stainless steel; organic VAG-31
Stud PAE-01 ASTM A 193 Gr B7 coated.
(Notes 8 and 1/2" - 1 "
Nut 14) ASTM A 194 Gr 2H
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 C
CLIENT: SHEET:
E&P 42 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
BW-Ballast (Notes 9, 10 and 11); DA-Open Drain (Note 12); IWC-
ASME B31.3 Aerated Sea Injection Water (Note 9); SW-Aerated Sea Water (Notes 9, 0ºC / 90ºC _____ (Note 13) B22
10 and 11)
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG) (Colapse)
up to 60 145
70 137
80 123
90 100
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This Spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have be enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the designs, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 When Classifier especifies metallic material, Spec B14 must be used and valves shall be according to Spec B22.
10 For the Naval System use Spec B15 only.
11 For Maximum working pressure greater than 150 PSIG, use Spec B23.
12 When Classifier especifies metallic material, Spec B9 must be used valves shall be according to Spec B22.
13 Table according - Pressure / Temperature rating.
14 The torque limit for FRP flanges shall be accordance with piping manufacturer.
15 Use plan washers to distribute the load of FRP flange.
This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
16
17 Do not use FRP when the risk of the piping rupture may cause flood with the lack of stability and integrity.
18 VB and VG may be used to atenuate the water hammer.
19 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
20 When required Fuly Tight (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 43 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Corrosion
CODE Service (Notes 14, 15 and 17) Temp. Range Class Standard
Allowance
ASME B31.3 BW-Ballast (Notes 9 and 10); SW-Aerated Sea Water (Notes 9, 10 and 18) 0ºC / 90ºC _____ (Note 11) B23
Pipes and Fittings (Notes 2, 3, 4, 5, 6 and 15) Valves (Note 19)
Size Wall (mm)
Item Tag Ends Material Ball
(in) nominal
Size Description Tag
1" - 6" Ball valve; class 150; FRP; FF; FLG; . VE-471
FRP
ASTM F 1173-01
RTRP- I5B3SIFB30
(reinforced thermosetting resin pipe)
Butt and strap a - 4.1.1.1 (filament-wound) Gate valve; class 150; FLG; FF; carbon
Pipe T-27 1" - 32" (Note 7)
joint b - 4.1.2 resin type (according to
2" - 12"
steel; organic coating.
VG-109B
d - 4.2.3 (test of long duration) Gate valve; class 150; FLG; FF; gear;
26" - 32" VG-110B
e - 4.3.1.3 (stagnated water) carbon steel; organic coating.
(Note 14)
Check
Check valve; horizontal piston; class
1" - 1 1/2" 150; FLG; FF; carbon steel; organic VR-147
coating.
Check valve; dual plate; wafer; class
2" - 24" 150; FLG; FF; carbon steel; organic VR-148
150 FRP coating.
According to ASTM D 4024-00 Check valve; dual plate; wafer; class
FLG-83 ASME B16.5 WN (FF) RTR-a;b;c 26" - 32" 150; FLG; FF; carbon steel; organic VR-148A
only for (reinforced thermosetting resin) coating.
dimensions a - 1 (Filament-wound)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 44 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Corrosion
CODE Service (Notes 14, 15 and 17) Temp. Range Class Standard
Allowance
ASME B31.3 BW-Ballast (Notes 9 and 10); SW-Aerated Sea Water (Notes 9, 10 and 18) 0ºC / 90ºC _____ (Note 11) B23
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Min. Press. (colapse) psig
90 150 up to 90 125
80 190
70 217
up to 60 230
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have be enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the design, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 When Classifier especifies metallic material, Spec B14 must be used and valves shall be according to Spec B23.
10 For the Naval System use Spec B15 only.
11 Table according - Pressure / Temperature rating.
12 The torque limit for FRP flanges shall be accordance with piping manufacturer.
13 Use plan washers to distribute the load of FRP flange.
14 This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
15 Do not use FRP when the risk of the piping rupture may cause flood with the lack of stability and integrity.
16 VB and VG may be used to atenuate the water hammer.
17 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
18 When Naval Systems to utilize of FRP, restricted to sea water discharge from inerte gas generators.
19 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 C
CLIENT: SHEET:
E&P 45 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service (Notes 9, 10 and 16) Temp. Range Class Standard
Allowance
ASME B31.3 FW-Fire water (Aerated sea water) (Note 11) 0ºC / 120ºC _____ (Note 12) B24
Pipes and Fittings (Notes 2, 3, 4, 5, 6 and 10) Valves (Note 15)
Size Wall (mm)
Item Tag Ends Material Ball
(in) nominal
Size Description Tag
(Note 9)
150
FRP
According to
ASTM D 4024-00
FLG-86 ASME B16.5 WN (FF)
RTR- a;b;c
only for
(reinforced thermosetting resin)
dimensions
Flange 1" - 16" Check
a - 1 (filament-wound) Check valve; horizontal piston; class 150;
1" - 1 1/2" VR-147
b - resin type - phenolic FLG; FF; carbon steel; organic coated.
FLG-88 16 BAR BLIND (FF)
c - production type - according to Check valve; dual plate; wafer; class 150;
manufacturer and approved for 2" - 16" FLG; FF; carbon steel; Viton seat; organic VR-148
CLASSIFIER coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 46 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service (Notes 9, 10 and 16) Temp. Range Class Standard
Allowance
ASME B31.3 FW-Fire water (Aerated sea water) (Note 11) 0ºC / 120ºC _____ 150 B24
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Min. Press. (colapse) psig
up to 90 150 up to 90 125
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 This spec shall be used according to IMO A 753, level L3.
3 Pipes and fittings must be made by the same manufacturer.
4 All the pipes, fittings and flanges shall have be enriched resin external liner and ultraviolet light inhibitor.
5 The supplier shall be responsible for the design, manufacture, assembly, maintenance, conditioning, inspection and testing of the piping.
6 The manufacturer shall have a Certificate of Type Approval issued by the Classifier.
7 Wall thickness shall be calculated for the manufacturer.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 This Spec should be according to appendix X3, paragraph X3.2.5.5 (electrical conductive) and appendix X4 (fatigue) with norm ASTM F1173-01.
10 Do not use FRP when the risk of the piping rupture may cause flood with the lack of stability and integrity.
11 Use only for fixed and uninhabited platforms.
12 Table according - Pressure / Temperature rating.
13 Use plan washers to distribute the load of FRP flange.
14 The torque limit for FRP flanges shall be accordance with piping manufacturer.
15 VB and VG may be used to atenuate the water hammer.
16 The piping designer/manufacturer should check the probability of the water hammer and provide a revision in the rote pipe in order to diminish.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 47 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 PCW-Produced water (on shore); DA-Open drain 0ºC / 60ºC _____ 150 B25
Pipe and Fittings (Notes 1, 2, 3, 4 and 13) Valves
Size Wall (mm)
Item Tag Ends Material Ball
(in) nominal
Red. Cross CRUZR-03 Check valve; dual plate; wafer; class 150; FF;
2" - 20" VR-90
S. R. ELL 90º CRC-12 stainless steel; Hypalon seat.
1" - 28" RJ/EE
S. R. ELL 45º CRC-13
FLG-82 JR/PF
1" - 28" 150
Flange FLG-81 JR/BF
According to RPVC - PVC extruded reinforced
(Notes 5, 11 and FLG-80 ASME B16.5 JE/PF external with thermosetting resin, Butterfly (Note 10)
2" - 28" only for fiber glass
12) FLG-79 JE/BF
dimensions Butterfly valve; wafer; max. pressure 150 psig;
8" - 10" VB-21
FLG-78 1" - 28" BLIND (FP) ductile iron, A351 CD4MCU disc, Hypalon seat.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 48 of 192
TECHNICAL SPECIFICATION ET-200.03
TITLE:
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Range Allowance
Class Standard
ASME B31.3 PCW-Produced water (on shore); DA-Open drain 0ºC / 60ºC _____ 150 B25
20 232
60 174
Branch Connections
Notes:
1 Wall thickness shall be according to NBR-7368.
2 Piping, conections and mend "Kit" should be the product of the same manufacturer.
3 Piping and conection should have ultraviolet inihibitor.
4 Water hammer shall be checked by the Engineering firm or the manufacturer.
5 The limit of torque for RPVC flanges should be based at piping diameter. Excess torque can damague the flange.
6 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
7 Use plan washers with narrow seat ASME B 27.2 tipo A.
8 For branches, use Tee or reduction Tee.
9 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
10 Butterfly valve way be used for diameters upon 6".
11 Dimensions according ASME B16.5 class 150.
12 For flanges with dimensions greater than NPS 24 according ASME B16.47 series A for class 150.
13 For piping PP mend, use weld as the best choise at PVC.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 49 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 F-Safety System and Flare (Note 7) 0ºC / 60ºC ___ 150 B30
Pipes and Fittings Valves
Size
Item Tag Wall or Class Ends Material Ball (Note 6)
(in)
1/2" SCH 40S 0,109" Size Description Tag
Pipe
ASTM B564
Cross CRUZ-44 3000 SW
(UNS N06625)
Red. Coupling LRE-21
Union UN-29
Coupling L-33
Butterfly
Globe
Compressed non-asbestos
Gasket JPH-07 1/2" - 1 1/2" 1/16" (1,6mm)
RF (aramida fiber and NBR)
(Note 5)
JI-01 1/2" - 1 1/2" 1/8" (3,2mm) Fenolic resin with neoprene
Other
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 50 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 F-Safety System and Flare (Note 7) 0ºC / 60ºC ___ 150 B30
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 290
50 283
60 278
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Isolating joint see drawing on the appendix 15.
6 When required Fully Tight valve (VET), see types in appendix 14.
7 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 D
SHEET:
E&P 51 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
ASME B31.3 D-Diesel (Note 6); FG-Fuel Gas (Note 7); H-Hydraulic Fluid;
PC-Process (Corrosive hydrocarbon) (Note 8 and 12)
-46°C/149ºC ________ 300 C3
Pipes and Fittings Valves (Note 9)
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-33 1/2" - 1 1/2" Sch 40S PLAIN ASTM A 312 Gr TP 316L seamless Size Description Tag
2" - 4" Sch 10S Ball valve; class 800; SW; stainless
1/2" - 1 1/2" VE-230
6" - 14" Sch 40S steel, RPTFE® V seat.
ASTM A 358 Gr TP 316L CL 1 or 3
Pipe T-34 (Note 13) BW
welded (E=1)
16" - 20" Sch 80S Ball valve; class 300; FLG; RF;
2" - 4" VE-314
24" 0,625" stainless steel, RPTFE® seat.
Cap TAM-38
Union UN-25
Coupling L-29
Fittings and Accessories
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
TECHNICAL SPECIFICATION
D
SHEET:
E&P 52 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
ASME B31.3 D-Diesel (Note 6); FG-Fuel Gas (Note 7); H-Hydraulic Fluid;
PC-Process (Corrosive hydrocarbon) (Note 8 and 12)
-46°C/149ºC ________ 300 C3
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 719
50 698
100 612
149 743
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Use only downstream centrifuge.
7 Use only downstream filters.
8 Use according appendix 5.
9 When required Fully Tigh valve (VET), see types in appendix 14.
10 Isolating joint see drawing on the appendix 15.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
13 From -46°C to -30°C material shall be solution heat-treaded.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 53 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
API 5L Gr B PSL 1
T-02A
seamless
Coupling L-04
Union UN-04
API 5L Gr B PSL 1 seamless
Short Nip. Gate
Fittings and Accessories
T-05A PLAIN
Long Nip. Gate valve; class 800; SW;
1/2" - 1 1/2" VG-45
Red.Nip.C NIPRC-04 carbon steel.
Cap TAM-02
Cross CRUZ-02
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 54 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
100 675
150 654
200 635
250 607
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 When required Fully Tight valve (VET), see types in appendix 14.
7 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B 31.3.
8 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 A
CLIENT: SHEET:
E&P 55 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 90ºC
ASME B31.3 FP-Production and Drilling Fluid
(Note: 5)
(3,2mm) 300 C5
Pipes and Fittings Valves
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-05A 3/4" XXS PLAIN API 5L Gr B PSL 1 seamless Size Description Tag
API 5L Gr B PSL 1
Pipe seamless or welded
T-02A/T-02B 2" - 6" Sch 80 BW
ERW or ERW / HFIW 3/4" Ball valve; class 800; SW; carbon steel. VE-48D
(E=0,85) (Note 7)
Tee TE-02
Wall
Red. Tee TRE-01 thickness ASTM A 234 Gr WPB
2" - 6" BW
Conc. Red. REDC-01 according to
pipe
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Gate (Note 4)
Gate valve; abrasive; FLG; RTJ; carbon
2 1/16" - 4 1/16" VG ABRAS-04
steel; API 2000 PSI, CWP
Globe
Check
Check valve; dual plate; wafer; class 300;
2" - 6" VR-36
RF; carbon steel; Viton seat.
Other
Flange FLG-10A 2" - 6" 300 WN (RF)
ASTM A 105
(Note 4) FLG-13 2" - 4" 600 WN (RTJ)
Compressed non-asbestos
JPH-11 2" - 6" 1/16" (1,6mm) RF
(aramida fiber and NBR)
Gasket
(Note 2) Carbon steel coated Zn-Ni max.
JA-01 2" - 4" 600 Oval
hardness 90 Brinell
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 56 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 90ºC
ASME B31.3 FP-Production and Drilling Fluid
(Note: 5)
(3,2mm) 300 C5
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 741
50 726
90 665
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
5 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
6 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B 31.3.
7 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 57 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS
Temp. Corrosion
CODE Service (Note 6) Class Standard
Range Allowance
G-Glycol; GL-Refrigerated Liquified Petroleum Gases (Flare
-46ºC /
ASME B31.3 Process, Drain System) in Low Temperature; F-Safety
System and Flare; P-Process (Non-Corrosive Hydrocarbon)
110ºC
(1,6mm) 300 C6
Pipes and Fittings Valves (Note 8)
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" Sch 160 0,188" Size Description Tag
3/4" Sch 160 0,219" Ball valve; class 800; SW;
T-09 PLAIN 1/2" - 3/4" VE-91C
1" Sch 80 XS 0,179" carbon steel.
E&P 58 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS
Temp. Corrosion
CODE Service Class Standard
Range Allowance
G-Glycol; GL-Refrigerated Liquified Petroleum Gases (Flare
-46ºC /
ASME B31.3 Process, Drain System) in Low Temperature; F-Safety
System and Flare; P-Process (Non-Corrosive Hidrocarbon)
110ºC
(1,6mm) 300 C6
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46/38 746
50 726
100 675
110 671
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of
the ISO 15156 (NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 D
SHEET:
E&P 59 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 1) Class Standard
Range Allowance
-18ºC / 54ºC
ASME B31.3 DO-Carbon Dioxide (DRY)
(Note 7)
____ 300 C8
Pipes and Fittings (Notes 2 and 5) Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
API 5L Gr B PSL 1 seamless
T-05A 1/2" - 1 1/2" PLAIN Size Description Tag
(Note 2)
API 5L Gr B PSL 1
T-02A seamless
Pipe
Sch 80 (Note 2)
(Note 2 e 4 ) Ball valve; class 800; Threaded;
2" - 8" BW 1/2" - 1 1/2" VE-01
API 5L Gr B PSL 1 carbon steel.
welded ERW or ERW / HFIW
T-02B
or seamless
(Note 2) and (Note 8)
Elbow 90º JO-07
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
T-05A API 5L Gr B PSL 1 seamless
Long Nip.
PLAIN
Red. Nip. C NIPRC-04
Cap TAM-02
Cross CRUZ-02
Check
Check valve, horizontal piston;
1/2" - 1 1/2" class 800; threaded; carbon VR-01
steel.
Other
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 60 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 1) Class Standard
Range Allowance
-18ºC / 54ºC
ASME B31.3 DO-Carbon Dioxide (DRY)
(Note: 6)
____ 300 C8
Pressure / Temperature Rating
-18 to 38 741
54 722
Branch Connections
Notes
1 This Spec shall be applied for distribution system of CO2, after directional valves.
2 Pipes, connections and fittings shall be galvanized according ASTM A123, after fabrication of the pipe spool.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 From -18ºC to 0ºC material must be normalized.
5 When manufactured news header or sections of header, shall be desing avoid weld in support of header.
6 Use niple THD X PLAIN and threaded cap (TAM-04) after drains and vents blocking.
7 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B 31.3.
8 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 61 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 240ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 6 , 9 and 13) (3,2mm) 300 C9
Pipes and Fittings Valves (Note 11)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2" - 3/4" XXS API 5L Gr B PSL 1 Size Description Tag
T-05A PLAIN
1" - 1 1/2" seamless
Ball valve; class 800; SW; carbon steel,
Sch 80 1/2" - 3/4" VE-333D
2" - 8" API 5L Gr B PSL 1 RPTFE® seat, up to 150ºC.
seamless or welded
T-02A/T-02B
10" ERW or ERW / HFIW
Ball valve; class 800; SW; carbon steel,
Sch 60 (E=0,85) (Note 15) 1" - 1 1/2" VE-333B
RPTFE® seat, up to 150ºC.
Pipe 12" - 18"
20" 0.750" BW API 5L Gr B PSL 1 welded Ball valve; class 300; FLG; RF; carbon VE-316
T-02B 2" - 4"
24" 0.875" (E=0,85) steel, RPTFE® seat, up to 150ºC. VE-318
Elbow 45º JO-10 1/2" - 3/4" Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-305B
Equal Tee TE-06 PEEK® seat, 150ºC to 220°C.
Red. Tee TRE-03 1/2" - 1 1/2" Ball valve; class 300; FLG; RF; carbon VE-343
2" - 4"
Cross CRUZ-06 steel, PEEK® seat, 150ºC to 220°C. VE-344
6000
Half Coupling ML-03 Ball valve; class 300; FLG; RF; gear;
6" - 24" VE-357
Red. Coupling LRE-02 carbon steel, PEEK® seat, 150ºC to 220°C.
1/2" - 3/4"
Cap TAM-06 Ball valve; class 800; SW; carbon steel,
1/2" - 3/4" VE-48D
Union UN-05 over 220ºC.
(Notes 1 and 7)
Red. Tee TRE-02 Ball valve; class 300; FLG; RF; gear;
6" - 24" VE-70
Cross CRUZ-05 carbon steel, over 220ºC.
1" - 1 1/2" 3000
Half Coupling ML-02 Ball valve; fire tested; class 800; SW;
1/2" - 3/4" VE-337D
Red. Coupling LRE-01 carbon steel, RPTFE® seat, up to 150ºC.
Fittings and Accessories
Coupling L-04 Ball valve; fire tested; class 300; FLG; RF; VE-358
2" - 4"
Short Nip. carbon steel, RPTFE® seat, up to 150ºC. VE-359
API 5L Gr B
T-05A
Long Nip. PSL 1 seamless Ball valve; fire tested; class 300; FLG; RF;
1/2" - 1 1/2" PLAIN 6" - 24" gear; carbon steel, RPTFE® seat, up to VE-360
Red.Nip.C NIPRC-04 150ºC
Red .Nip.E NIPRE-10 Ball valve; fire tested; class 800; SW;
1/2" - 3/4" carbon steel, PEEK® seat, 150ºC to VE-309D
Red.Nip.C NIPRC-04A 200ºC.
1/2" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A Ball valve; fire tested; class 800; SW;
1" - 1 1/2" VE-309B
S.R.ELL 90º CRC-01 2" - 24" carbon steel, PEEK® seat, 150ºC to 200ºC.
Wall
L.R.ELL 90º CRL-01 thickness Ball valve; fire tested; class 300; FLG; RF; VE-361
2" - 4"
L.R.ELL 45º CRL-02 according to ASTM A 234 Gr WPB carbon steel, PEEK® seat, 150ºC to 200ºC. VE-362
pipe
Tee TE-02 Ball valve; fire tested; class 300; FLG; RF;
6" - 24" gear; carbon steel, PEEK® seat, 150ºC to VE-363
Red. Tee TRE-01 200ºC.
BW
Conc. Red. REDC-01 2" - 32"
Weldolet WOL-01 ASTM A 105 Gate valve; class 300; FLG; RF; carbon
2" - 8" VG-05
FLG-41A 1/2" - 1 1/2" SW (RF) steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 62 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 240ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 6, 9 and 13) (3,2mm) 300 C9
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 741
50 726
100 675
110 671
240 613
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194 Gr 7
nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
a) The maximun hardness of any compnent of these especifications should be 22 RC (239 Brinell) according NACE MR0175.
b) The materials should be have a thermic treatment after welding.
c) The bolts (including valves bolts) should be used according norm NACE MR0175.
7 Use niple THD X BW and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
8 Flanges ≤ 1 1/2" may be used, if strictly necessary.
9 For temperature betwen 110º C to 240ºC, use Spiral-Wound Gasket.
10 Isolating joint see drawing on the appendix 15.
11 When required Fully Tight valve (VET), see types in appendix 14.
12 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE MR0175)
14 Impact test requirements according API 5L standard.
15 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 G
SHEET:
E&P 63 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, Non-
Corrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection (Note
0ºC / 240ºC
ASME B31.3 9); G-Glycol; SN- Start-up Nitrogen; SA-Service Compressed Air (Utility Air); P-Process
(non-corrosive hydrocarbon) (Note 17); D-Diesel (Note 8); FG-Fuel Gas (Note 10); AM-
(Note 16)
(1,6mm) 300 C10
Amine (Note 15).
Pipes and Fittings (Note 14) Valves (Note 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2" - 3/4" Sch 160 Size Description Tag
T-05A PLAIN
1" - 1 1/2" Ball valve; class 800; SW;
API 5L Gr B PSL 1
Sch 80 1/2" - 3/4" carbon steel, RPTFE® seat, up VE-341C
2" - 3" seamless
to 150ºC.
T-02A
Ball valve; class 800; SW;
Pipe 4" - 10" Sch 40
1" - 1 1/2" carbon steel, RPTFE® seat, up VE-333B
2" - 3" Sch 80 to 150ºC.
BW
4" - 10" API 5L Gr B PSL 1 VE-316
T-02B welded ERW or ERW / HFIW Ball valve; class 300; FLG; RF;
12" - 20" Sch 40 (E=0,85) (Note 18) 2" - 4" carbon steel, RPTFE® seat, up
to 150ºC.
24" VE-318
JPH-12 12" - 24" 1/8" (3,2mm) (aramida fiber and NBR) Check
JE-07 1/2" - 3" Stainless steel AISI 304 with flexible- Check valve, horizontal piston;
Gasket 1/2" - 1 1/2" VR-56
RF graphite class 800, SW, carbon steel.
(Notes 11 and 12) JE-08 4" - 6" 0,175" (4,4mm)
Stainless steel AISI 304 with flexible- Check valve, dual plate; wafer;
JE-09 8" - 24" 2" - 24" VR-36
graphite, with inner ring AISI 304 class 300; RF; carbon steel;
JI-03 1/2" - 24" 1/8" (3,2mm) Fenolic resin with neoprene Check valve, dual plate; wafer;
2" - 24" class 300; RF; carbon steel; VR-29
Stud PAE-01 ASTM A 193 Gr B7 metal-metal (over 200ºC).
1/2" - 1 "
Nut (Note 2) ASTM A 194 Gr 2H
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 G
CLIENT: SHEET:
E&P 64 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial Water (Fresh, Non-
Corrosive / De-Aerated Sea Water); IW-Fresh And De-Aerated Sea Water Injection (Note
0ºC / 240ºC
ASME B31.3 9); G-Glycol; SN- Start-up Nitrogen; SA-Service Compressed Air (Utility Air); P-Process
(non-corrosive hydrocarbon) (Note 17); D-Diesel (Note 8); FG-Combustible Gas (Note
(Note 16)
(1,6mm) 300 C10
10); AM-Amine (Note 15).
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 740
50 726
100 675
240 613
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grage B16 stud
bolts and ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 or TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Use only upstream centrifuge.
9 Use only in onshore installations.
10 Use only upstream filters.
11 For temperature betwen 110º C to 240ºC, use Spiral-Wound Gasket.
12 Isolating joint see drawing on the appendix 15.
13 When required Fully Tight Valve (VET), see types in appendix 14.
14 Onshore instalation use DN 2" and 3" sch 40.
15 For use booster pump discharge.
16 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
17 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
18 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 65 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 120ºC
ASME B31.3 PCW-Produced water
(Note: 11)
___ 300 C11
Pipes and Fittings (Organic coating - according appendix 18) (Notes 7 and 8) Valves (Organic coated - acc. appendix 18) (Note 9)
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-05A 1" - 1 1/2" PLAIN Size Description Tag
Sch 80 API 5L Gr B PSL 1
2" - 3" Ball valve; class 300; FLG, RF; carbon
T-02A seamless 1" - 1 1/2" VE-201
4" - 14" Sch 40 steel, RPTFE® seat; organic coated.
BW
Pipe 2" - 3" Sch 80 API 5L Gr B PSL 1 VE-193
Ball valve; class 300; FLG; RF; carbon
T-02B welded ERW or ERW / HFIW 2" - 4"
4" - 16" Sch 40 steel, RPTFE® seat; organic coated. VE-195
(E=0,85) (Note 12)
Ball valve; class 300; FLG; RF; gear;
6" - 16" carbon steel, RPTFE® seat; organic VE-197
coated.
Elbow 90º JO-07 Ball valve; fire tested; class 300; FLG;
1" - 1 1/2" RF; carbon steel;RPTFE/metal seat, VE-205
Elbow 45º JO-08 organic coating.
Equal Tee TE-05 Ball valve; fire tested; class 300; FLG; VE-206
2" - 4" RF; carbon steel; RPTFE/metal seat,
Red. Tee TRE-02 organic coating. VE-207
1" - 1 1/2" 3000 SW ASTM A 105 6" - 16" RF; gear; carbon steel; RPTFE/metal VE-208
Half Coupling ML-02 seat, organic coating.
Red. Coupling LRE-01
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
T-05A API 5L Gr B PSL 1 seamless
Long Nip.
1" - 1 1/2" PLAIN
Red.Nip.C NIPRC-04
Fittings and Accessories
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A Gate (Note 4)
S.R.ELL 90º CRC-01 Gate valve; class 300; FLG, RF; carbon
Wall 1" - 1 1/2" VG-85
L.R.ELL 90º CRL-01 steel; organic coated.
thickness
L.R.ELL 45º CRL-02 according to ASTM A 234 Gr WPB Gate valve; class 300; FLG, RF; carbon
pipe 2" - 8" VG-81
Tee TE-02 steel; organic coated.
Red. Tee TRE-01 Gate valve; class 300; FLG, RF; gear;
2" - 16" BW 10" - 16" VG-82
Conc. Red. REDC-01 carbon steel; organic coated.
Check
Check valve; horizontal; piston; class
1"- 1 1/2" 300; FLG, RF; carbon steel, organic VR-117
coated.
Check valve; dual plate; wafer; class
2" - 16" VR-115
300; RF; carbon steel, organic coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 66 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
0ºC / 120ºC
ASME B31.3 PCW-Produced water
(Note: 11)
___ 300 C11
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
To 38 740
50 726
100 675
120 667
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
7 Onshore instalation use DN 2" and 3" sch 40.
8 All pipes shall be organic coated according appendix 18.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM A 194
Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
11 All nominal thicknesses checked the limits of low temperature according to the criteria of the ASME B 31.3 code.
12 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
Elbow 45º JO-30 Ball valve; fire tested, class 800; SW;
1/2" - 1 1/2" VE-364
Equal Tee TE-18 superduplex stainless steel.
Red. Tee TRE-13 Ball valve; fire tested, class 300; FLG;
2" - 4" VE-369
Cross CRUZ-18 RF; superduplex stainless steel.
ASTM A 182 Gr F 55
3000 SW
(UNS S32760)
(Notes 1 and 3)
Half Coupling ML-12 Ball valve; fire tested, class 300; FLG;
6" - 24" VE-370
Red. Coupling LRE-08 RF; gear; superduplex stainless steel.
1/2" - 1 1/2"
Cap TAM-22
Union UN-15
Coupling L-16
Cross CRUZ-21
ASTM A 182 Gr F 55
Weldolet WOL-05
(UNS S32760)
Check
Check valve; horizontal piston; class
1/2" - 1 1/2" 800; sw; RF; super duplex stainless VR-87
steel.
Check valve, dual plate; class 300; RF,
2" - 24" super duplex stainless steel; Viton seat VR-73
TBR-S.
Other
Globe valve, needle disc; 3000 PSIG,
1/2" - 1 1/2" VAG-28
SW, stainless steel superduplex.
E&P 68 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 140ºC
ASME B31.3 PC-Process (Corrosive Hidrocarbon) (Notes 5 and 12). _______ 300 C12
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 749
50 749
100 735
120 707
140 665
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-44) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
9 For temperature over 110ºC, use spiral gaskets.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156
(NACE MR0175)
13 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 C
SHEET:
E&P 69 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
This SPEC shall be used only repair, when the plant material was designed in 0ºC / 120ºC
ASME B31.3
according to (UNS S32750). For new project use espec C12 (UNS S32760).
_______ 300 C13
Pipes and Fittings (Note 6) Valves (Note 7)
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-13 1/2" - 1 1/2" Sch 40S PLAIN Size Description Tag
ASTM A 790 (UNS S32750)
seamless Ball valve; class 800; SW; superduplex
T-15 2" - 8" 1/2" - 1 1/2" VE-74
stainless steel.
Pipe
Sch 10S BW
10" - 20" ASTM A 928 (UNS S32750
Ball valve; class 300; FLG; RF; superduplex
T-48 class 1 or 3) 2" - 4" VE-78
stainless steel.
welded (E=1)
24"
Elbow 90º JO-27 Ball valve; class 300; FLG; RF; gear;
6" - 24" VE-79
Elbow 45º JO-28 superduplex stainless steel.
Union UN-14
Coupling L-15
Cross CRUZ-20
Check
Other
FLG-102 1/2" - 1 1/2" SW (RF) Globe valve; needle disc; 3000 psig; SW;
Flange ASTM A 182 Gr F53 1/2" - 1 1/2" VAG-29
FLG-101 1/2" - 24" 300 BLIND (RF) stainless steel superduplex.
(Note 4) (UNS S32750)
FLG-100 2" - 24" WN (RF)
E&P 70 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
This SPEC shall be used only repair, when the plant material was designed in 0ºC / 120ºC
ASME B31.3
according to (UNS S32750). For new project use espec C12 (UNS S32760).
_______ 300 C13
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 749
50 749
100 735
120 707
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-45) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Isolating joint see drawing on the appendix 15.
6 According appendix 16 - Welding qualification requirements for superduplex.
7 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
E&P 71 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
IW-Fresh And De-Aerated Sea Water Injection (Note 2); SW-Aerated Sea Water 0ºC / 70ºC
ASME B31.3
(Note 3) (Note: 9)
_____ 300 C14
Pipes and Fittings (Coated with polyethylene, according to appendix 13) Valves
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-05A 1" - 1 1/2" PLAIN API 5L Gr B PSL 1 Size Description Tag
T-02A seamless
Sch 80 Ball valve; class 300; FLG; FF; carbon
2" - 3" API 5L Gr B PSL 1 welded 1" - 1 1/2" VE-45
T-02B steel.
(E=0,85)
Pipe T-02A API 5L Gr B PSL 1 seamless Ball valve; class 300; FLG; FF; carbon VE-18E
4" - 10" 2" - 4"
(Note 8) BW steel.
VE-11E
Sch 40
12" - 20" API 5L Gr B PSL 1
T-02B Ball valve; class 300; FLG; FF; gear;
24" welded (E=0,85) 6" - 24" VE-23E
carbon steel.
26" - 32" Sch 20
Elbow 90º JO-07 Ball valve; class 300; FLG; FF; gear;
26" - 32" VE-23F
Elbow 45º JO-08 carbon steel.
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
Cap TAM-02
Cross CRUZ-02
Check
FLG-10D WN (FF)
26" - 32"
FLG-11D BLIND (FF)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
E&P 72 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
IW-Fresh And De-Aerated Sea Water Injection (Note 2); SW-Aerated Sea Water 0ºC / 70ºC
ASME B31.3
(Note 3) (Note: 9)
_____ 300 C14
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 741
50 726
70 706
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 Use when the metalic material is required by classifier.
4 Isolating joint see drawing on the appendix 15.
5 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
8 Piping, conections and fittings should be revested with polyethylene according appendix 13.
9 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 73 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
-46ºC / 130ºC
ASME B31.3 AM-Amina; PC-Process (Corrosive Hydrocarbon) (Note 5 and 13)
(Note 11)
_______ 300 C16
Pipes and Fittings (Note 7) Valves (Notes 8 and 10)
Size
Item Tag Wall or Class Ends Material Ball
(In)
1/2" SCH 40S STD 0,109" Size Description Tag
3/4" SCH 40S STD 0,113" Ball valve; class 800; SW; duplex
T-36 PLAIN 1/2" - 1 1/2" VE-209
1" SCH 40S STD 0,133" steel, RPTFE® seat.
1 1/2" SCH 40S STD 0,145" ASTM A 790 (UNS S31803) Ball valve; class 300; FLG; RF; duplex
2" - 4" VE-216
2" SCH 10S STD 0,109" seamless steel, RPTFE® seat.
3"-4" SCH 10S 0,120" Ball valve; class 300; FLG; RF; gear;
Pipe T-37A 6" - 24"
duplex steel, RPTFE® seat.
VE-217
6" SCH 10S 0,134"
8" SCH 10S 0,148" Ball valve; fire tested; class 800;
BW 1/2" - 1 1/2" VE-212
10" SCH 10S 0,165" SW; duplex steel.
Union UN-23
Coupling L-27
S.R.ELL 90º CRC-22 Gate valve; class 300; FLG; RF; gear;
10" - 24" VG-93
L.R.ELL 90º CRL-30 Wall duplex steel.
thickness
L.R.ELL 45º CRL-31 according to ASTM A 815 (UNS S31803) Globe
Tee TE-39 pipe
Globe valve; class 300; FLG; RF;
2" - 10" VGL-84
Red. Tee TRE-34 duplex steel.
Cap TAM-36
Cross CRUZ-33
ASTM A 182 Gr F 51
Weldolet WOL-07
(UNS S31803)
Check
FLG-123 1/2" - 1 1/2" SW (RF) Check valve; horizontal piston; class
Flange ASTM A 182 Gr F 51 1/2" - 1 1/2" VR-119
FLG-124 1/2" - 24" 300 BLIND (RF) 800; sw; duplex stainless steel.
(Note 4) (UNS S31803)
FLG-125 2" - 24" WN (RF) Check valve, wafer, dual plate; class
2" - 24" 300; RF, duplex steel; Viton seat TBR- VR-122
JPH-11 1/2" - 10" 1/16" (1,6mm) Compressed non-asbestos S.
JPH-12 12" - 24" 1/8" (3,2mm) (aramida fiber and NBR)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 74 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
-46ºC / 130ºC
ASME B31.3 AM-Amina; PC-Process (Corrosive Hydrocarbon) (Note 5 and 13)
(Note 11)
_______ 300 C16
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-46 to 38 749
50 749
100 735
110 721
130 693
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-45) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex.
9 For temperature over 110ºC, use spiral gaskets.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
14 Use this Spec after the first Production Separator to the PC service.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 A
CLIENT: SHEET:
E&P 75 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
AND MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 150ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 10 and 12)
(Note 11)
___ 300 C30
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 9) Valves
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2' SCH 40S 0,109" Size Description Tag
3" SCH 40 STD 0,216" Ball valve; fire tested; class 300; FLG;
6" - 24" RF; gear; carbon steel + Inconel® 625; VE-466
4" SCH 40 STD 0,237" API 5L Gr B PSL 1 RPTFE®/metal seat.
T-02A 6" SCH 40 STD 0,280" seamless
or or
Pipe T-03B 8" SCH 20 0,250" API 5L Gr B PSL 1
10" SCH 20 0,250" welded (E=0,95)
12" 0,281" BW
18" 0,406"
API 5L Gr B PSL 1
T-03B 20" 0,438"
welded (E=0,95)
24" SCH 30 0,562" Gate
26" 0,562
PLAIN
Red. Nip. C NIPRC-16 Inconel® 625
Globe valve; class 300; FLG; RF;
ASTM B564 1/2" - 12" VGL-96
Red. Nip. E NIPRE-22 carbon steel + Inconel® 625.
(UNS N06625)
E&P 76 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
AND MARINE SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 150ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 10)
(Note 11)
___ 300 C30
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 740
50 727
100 676
150 654
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Gr B16 stud
bolts and ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
7 Isolating joint see drawing on the appendix 15.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 All piping and fittings shall be internal Inconel® 625 coated according Appendix 16.
10 Use this Spec after choke valve until the arrival of the first Production Separator.
11 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
12 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO
15156 (NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 77 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
AM-Amine (Note 8); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
-100ºC /
ASME B31.3 D-Diesel; FG-Fuel Gas (Note 6); H-Hydraulic Fluid; PC-Process (Corrosive
Hydrocarbon) (note 12);
190ºC
______ 600 E3
Pipes and Fittings Valves (Note 7 )
Size
Item Tag Wall or Class Ends Material Ball
(in)
T-33 1/2" - 1 1/2" Sch 40S PLAIN ASTM A312 Gr TP 316L seamless Size Description Tag
Globe
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 78 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
AM-Amine (Note 8); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
-100ºC /
ASME B31.3 D-Diesel; FG-Combustible Gas (Note 6); H-Hydraulic Fluid; PC-Process (Corrosive
Hydrocarbon) (note 12);
190ºC
______ 600 E3
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1200
50 1160
100 1010
150 911
190 859
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Use only downstream filters.
7 When required fully tight valve (VET) for DR-ENGP-2.1, see types in appendix 14.
8 For use Gas Inlet and Outlet from Amine Contactors.
9 For -101°C to -30°C material shall be solution heat-treated.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 Isolating joint see drawing on the appendix 15.
12 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 79 of 192
TITLE: TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 S-Steam; SC-Steam Condensate; HWP-Process Heating Water 0ºC / 350ºC (1,6mm) 600 E4
Pipes and Fittings Valves (Note 6)
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 1/2" - 1 1/2" PLAIN Size Description Tag
Sch 80
2" API 5L Gr B PSL 1
seamless or welded
3" Sch 40
T-02A/T-02B ERW or ERW / HFIW
(E=0,85) (Note 9)
Pipe 4" - 10"
BW
Sch 80
12" - 20" API 5L Gr B PSL 1
T-02B
welded (E=0,85)
24"
Cross CRUZ-05
3000 SW ASTM A 105
Half Coupling ML-02
Union UN-04
Coupling L-04
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 80 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 S-Steam; SC-Steam Condensate; HWP-Process Heating Water 0ºC / 350ºC (1,6mm) 600 E4
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
200 1270
220 1249
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 When required Fully Tight valve (VET), see types in appendix 14.
7 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
8 Impact test requirements according API 5L standard.
9 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
CLIENT: SHEET:
E&P 81 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 90ºC
ASME B31.3 FP-Production and drilling fluid
(Note: 5)
(3,2mm) 600 E5
Pipes and Fittings Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 3/4" XXS PLAIN API 5L Gr B PSL 1 seamless Size Description Tag
Tee TE-02
Wall
Red. Tee TRE-01 thickness ASTM A 234 Gr WPB
2" - 8" BW
Conc. Red. REDC-01 according to
pipe
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Gate (Note 4)
Gate valve; abrasive; FLG; RTJ; carbon
2 1/16" - 9" VG ABRAS-04
steel; API 2000 PSIG; CWP.
Globe
Check
Check valve; dual plate; class 600; RTJ;
2" - 8" VR-38
carbon steel; Viton seat.
Other
Flange FLG-13 2" - 8" WN (RTJ)
600 ASTM A 105
(Note 4) FLG-15 2" - 8" BLIND (RTJ)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 82 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 90ºC
ASME B31.3 FP-Production and drilling fluid
(Note: 5)
(3,2mm) 600 E5
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 1480
50 1453
90 1372
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gasket must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
5 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
6 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 83 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 5) Class Standard
Range Allowance
G-Glycol; GL-Refrigerated Liquified Petroleum Gases (Flare Process, Drain
ASME B31.3
System) low Temperature; P-Process (Non corrosive hydrocarbon) (Note 10) .
-46ºC / 110ºC (1,6mm) 600 E6
Pipes and Fittings Valves (Note 9)
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" - 3/4" Sch 160 Size Description Tag
T-09 PLAIN
1" - 1 1/2" ASTM A 333 Gr 6 Ball valve; class 800; SW;
1/2" - 3/4" VE-91C
2" - 3" seamless carbon steel.
T-07A
4" - 14"
Pipe 1" - 1 1/2"
Ball valve; class 800; SW;
VE-91B
Sch 80 carbon steel.
BW
16" - 20" ASTM A 671 Gr CC 60 CL 22
T-08
welded (E=1) Ball valve; class 600; FLG; RTJ;
2" - 4" VE-92
carbon steel.
24"
Cross CRUZ-12
6000
Half Coupling ML-07
Union UN-09
(Notes 1 and 6)
Coupling L-09
SW ASTM A 350 Gr LF2 CL1
Elbow 90º JO-13
Cross CRUZ-09
1" - 1 1/2" 3000
Half Coupling ML-05
Cap TAM-09
Union UN-07
Coupling L-08
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 84 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 5) Class Standard
Range Allowance
G-Glycol; GL-Refrigerated Liquified Petroleum Gases(Flare Process, Drain
ASME B31.3
System) low Temperature; P-Process (Non corrosive hydrocarbon) (Note 10).
-46ºC / 110ºC (1,6mm) 600 E6
Pressure / Temperature Rating
-46/38 1480
50 1453
100 1351
110 1343
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
6 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 85 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 5) Class Standard
Range Allowance
GL-Refrigerated Liquified Petroleum Gases (Flare Process, Drain System) Low
ASME B31.3
Temperature
-46ºC / 110ºC (1,6mm) 600 E6R
Pipes and Fittings Valves (Note 9)
Size Wall or
Item Tag Ends Material Ball
(in) Class
1/2" - 3/4" Sch 160 Size Description Tag
T-09 PLAIN
1" - 1 1/2" Ball valve; class 800; SW;
Sch 80 ASTM A 333 Gr 6 1/2" - 3/4" VE-91C
2" - 3" carbon steel.
seamless
Pipe T-07A 4" - 8" Sch 40 Ball valve; class 800; SW;
1" - 1 1/2" VE-91B
10" - 14" BW carbon steel.
Cross CRUZ-12
6000
Half Coupling ML-07
Union UN-09
(Notes 1 and 6)
Coupling L-09
SW ASTM A 350 Gr LF2 CL 1
Elbow 90º JO-13 Gate
Elbow 45º JO-14
Cross CRUZ-09
1" - 1 1/2" 3000
Half Coupling ML-05
Cap TAM-09
Union UN-07
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red .Nip.E NIPRE-16A
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 86 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 5) Class Standard
Range Allowance
GL-Refrigerated Liquified Petroleum Gases (Flare Process, Drain System) Low
ASME B31.3
Temperature
-46ºC / 110ºC (1,6mm) 600 E6R
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46/110 1030
110 1030
Notas:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
6 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 87 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 1) Class Standard
Range Allowance
-18ºC / 54ºC
ASME B31.3 DO-Carbon Dioxide
(Note: 6)
_______ 600 E8
Pipes and Fittings (Notes 2 and 5) Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
API 5L Gr B PSL 1 Size Description Tag
T-05A 1/2" - 1 1/2" PLAIN seamless
Pipe (Note 2 ) Ball valve; class 800; threaded;
Sch 80 1/2" - 1 1/2" VE-01
(Notes 2 and 4) API 5L Gr B PSL 1 carbon steel.
T-02A/T-02B 2" - 8" BW seamless or welded
ERW or ERW / HFIW (Note 2 and 7)
Elbow 90º JO-07
Cross CRUZ-05
3000 SW ASTM A 105 (Note 2)
Half Coupling ML-02
Union UN-04
Fittings and Accessories
Coupling L-04
Cap TAM-02
Check
Check valve, horizontal piston;
1/2" - 1 1/2" class 800, threaded; carbon VR-01
steel.
Other
FLG-13 WN (RTJ)
Flange 1" - 8" 600 ASTM A 105 (Note 2)
FLG-15 BLIND (RTJ)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 88 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service (Note 1) Class Standard
Range Allowance
-18ºC / 54ºC
ASME B31.3 DO-Carbon Dioxide
(Note: 6)
_______ 600 E8
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-18 to 38 1480
54 1445
Branch Connections
Notes:
1 This Spec should be applied for distribution system of CO2 before directional valves.
2 Pipes, connections and fittings shall be galvanized according ASTM A123, after fabrication of the pipe spool.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 From -18ºC to 0ºC material must be normalized.
5 When manufactured news header or sections of header, shall be desing avoid weld in support of header.
6 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
7 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 89 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 150ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 6) (3,2mm) 600 E9
Pipes and Fittings Valves (Note 10)
Size Wall or
Item Tag Ends Material Ball (Note 4)
(in) Class
API 5L Gr B PSL 1
T-05A 1/2" - 1 1/2" XXS PLAIN Size Description Tag
seamless
2" Sch 160 API 5L Gr B PSL 1 Ball valve; class 800; SW;
seamless or welded 1/2" - 1 1/2" carbon steel, Devlon V® seat, up VE-373D
T-02A/T-02B to 150ºC.
3" - 10" Sch 80 ERW or ERW / HFIW
(E=0,85) (Note 14) Ball valve; class 600; FLG; RTJ; VE-374
Pipe 2" - 4" carbon steel, DevlonV® seat, up
to 150ºC. VE-375
(Note 11) 12" - 14" Sch 100 BW
Ball valve; class 600; FLG; RTJ;
API 5L Gr B PSL 1 welded 6" - 20" gear; carbon steel, Devlon V® VE-376
T-02B 16" 1,031" seat, up to 150ºC.
(E=0,85)
18" 1,156" Ball valve; fire tested; class 800;
1/2" - 1 1/2" SW; carbon steel, Devlon V® VE-377D
20" 1,281" seat.
Elbow 90º JO-09 Ball valve; fire tested; class 600; VE-378
2" - 4" FLG; RTJ; carbon steel, Devlon
Elbow 45º JO-10 V® seat. VE-379
Red. LRE-02
1/2" - 1 1/2"
Cap TAM-06
Union UN-05
Coupling L-05
Short Nip.
T-05A API 5L Gr B PSL 1 seamless
Long Nip.
PLAIN
Red.Nip.C NIPRC-04
Fittings and Accessories
Red.Nip.C NIPRC-04A
1/2" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
Check
Check valve; horizontal piston;
1/2" - 1 1/2" VR-56
class 800; SW; carbon steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 90 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 150ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 6) (3,2mm) 600 E9
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1480
50 1453
100 1351
110 1343
150 1308
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 Gr B16 stud bolts and
ASTM A194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 For PC service, see appendix 5.
7 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
8 Flanges ≤ 1 1/2" may be used, if strictly necessary.
9 Isolating joint see drawing on the appendix 15.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Impact test requirements according API 5L standard.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
14 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 F
CLIENT: SHEET:
E&P 91 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial
Water (Fresh, Non-Corrosive / De-Aerated Sea Water); IW-Fresh And -20ºC / 210ºC
ASME B31.3
De-Aerated Sea Water Injection (Note 8); G-Glycol; FG-Fuel Gas
(1,6mm) 600 E10
(Note 9); P-Process (Non corrosive hydrocarbon) (Note 16); AM-
Pipes and Fittings (Note 12) Valves (Note 11)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2" Sch 160 0,188" 120 Description Tag
16" SCH 80 0,844" Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-382B
18" SCH 80 0,938 API 5L Gr X65 PSL 2 PEEK® seat, over 150°C.
T-45 welded
20" 1,062" (E=1) Ball valve; class 600; FLG; RTJ; carbon VE-383
2" - 4"
24" 1,312" steel, PEEK® seat, over 150°C. VE-384
Elbow 90º JO-09 Ball valve; class 600; FLG; RTJ; gear;
6" - 24" VE-385
Elbow 45º JO-10 1/2" - 3/4" carbon steel, PEEK® seat, over 150°C.
Equal Tee TE-06 Ball valve; fire tested; class 800; SW;
1/2" - 1 1/2" - 3/4" carbon steel, DEVLON V® seat, up to VE-393C
Red. Tee TRE-03 150ºC.
1/2"
Cross CRUZ-06 Ball valve; fire tested; class 800; SW;
6000 1" - 1 1/2" carbon steel, DEVLON® V seat, up to VE-393B
Half Coupling ML-03 150ºC.
Red. LRE-02 Ball valve; fire tested; class 600; FLG; VE-378
1/2" - 3/4" 2" - 4" RTJ; carbon steel, DEVLON® V seat, up
Cap TAM-06 to 150ºC. VE-379
Cross CRUZ-05 Ball valve; fire tested, class 600; FLG; VE-398
1" - 1 1/2" 3000 2" - 4" RTJ; carbon steel, PEEK® seat, up to
Half Coupling ML-02 150ºC. VE-399
Short Nip. Ball valve; class 800; SW; carbon steel, VE-401B
T-05A API 5L Gr B PSL 1 seamless 1" - 1 1/2"
Long Nip. TFE/P seat, over 150°C. (Note 15)
1/2" - 1
PLAIN
Red.Nip.C NIPRC-04 1/2" VE-402
Ball valve; class 600; FLG; RTJ; carbon
2" - 4" VE-403
Red .Nip.E NIPRE-10 steel, TFE/P seat, over 150°C.
(Note 15)
Red.Nip.C NIPRC-04A Ball valve; class 600; FLG; RTJ; gear; VE-404
1/2" - 4" BW/PLAIN 6" - 24"
Red .Nip.E NIPRE-10A carbon steel, TFE/P seat, over 150°C. (Note 15)
S.R.ELL 90º CRC-01 Ball valve; fire tested; class 800; SW; VE-405C
Wall 1/2" - 3/4"
L.R.ELL 90º CRL-01 thickness carbon steel, TFE/P seat, up to 150ºC. (Note 15)
according to ASTM A 234 Gr WPB
L.R.ELL 45º CRL-02 Ball valve; fire tested; class 800; SW; VE-405B
pipe 1" - 1 1/2"
Tee TE-02 carbon steel, TFE/P seat, up to 150ºC. (Note 15)
Red. Tee TRE-01 Ball valve; fire tested; class 600; FLG; VE-406
2" - 24" BW 2" - 4" RTJ; carbon steel, TFE/P seat, up to
Conc. Red. REDC-01 150ºC. VE-407
Ecc. Red. REDE-01 Ball valve; fire tested; class 600; FLG;
VE-408
6" - 24" RTJ; gear; carbon steel, TFE/P seat, up
Cap TAM-02 (Note 15)
to 150ºC.
Cross CRUZ-02 Gate (Note 5)
Weldolet WOL-01 ASTM A 105
1/2" - 1 1/2" Gate valve; class 800; SW; carbon steel. VG-45
E&P 92 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
BG-Inert Gas; CI-Chemical Injection (Non-Corrosive); W-Industrial
Water (Fresh, Non-Corrosive / De-Aerated Sea Water); IW-Fresh And
-20ºC / 210ºC
ASME B31.3 De-Aerated Sea Water Injection (Note 8); G-Glycol; FG-Combustible
Gas (Note 9); P-Process (Non corrosive hydrocarbon) (Note 16); AM-
(1,6mm) 600 E10
Amine (Nota 13).
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-20 to 38 1480
50 1450
100 1346
110 1340
150 1280
210 1200
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud
bolts and ASTM A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01 and TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Use only in onshore installations.
9 Use only upstream filters.
10 Isolating joint see drawing on the appendix 15.
11 When requerid Fully Tight Valve (VET), see types in appendix 14.
12 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
13 For use Amine Inlet from the Amine Contactors.
14 Impact test requirements according API 5L standard.
15 Use only for AM- amine.
16 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO
15156 (NACE MR0175)
17 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 93 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 110ºC
ASME B31.3 W-Industrial Water (Fresh, Non-Corrosive / De-Aerated Sea Water) (Note: 9) (1,6mm) 600 E10R
Pipes and Fittings Valves
Size Wall or
Item Tag Ends Material Ball (Note 4)
(in) Class
Size Description Tag
1/2" - 3/4' Sch 160
API 5L Gr B PSL 1 Ball valve; class 800; SW; carbon steel,
T-05A PLAIN 1/2" - 3/4" VE-381C
seamless DEVLON® V seat, up to 150ºC.
1" - 1 1/2" Sch 80
Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-381B
2" - 8" Sch 40 API 5L Gr B PSL 1 DEVLON® V seat, up to 150ºC.
Pipe seamless or welded
T-02A/T-02B Ball valve; class 600; FLG; RTJ; carbon VE-20
10" ERW or ERW / HFIW 2" - 4"
(E=0,85) (Note 10) steel. VE-13
BW
Sch 60
12" - 20" API 5L Gr B PSL 1 welded Ball valve; class 600; FLG; RTJ; gear;
T-03B 6" - 24" VE-25
(E=0,95) carbon steel.
24"
Elbow 90º JO-07
Cross CRUZ-05
3000 SW ASTM A 105
Half Coupling ML-02
(Notes 1 and 6)
Red. LRE-01
1/2" - 1 1/2"
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
T-05A API 5L Gr B PSL 1 sem costura
Long Nip.
PLAIN
Fittings and Accessories
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 A
CLIENT: SHEET:
E&P 94 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
0ºC / 110ºC
ASME B31.3 W-Industrial Water (Fresh, Non-Corrosive / De-Aerated Sea Water)
(Note: 9)
(1,6mm) 600 E10R
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1030
110 1030
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 Gr B16 stud bolts
and ASTM A194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3
10 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 95 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
Red. LRE-01
Cap TAM-05
Union UN-04
Coupling L-04
Cross CRUZ-02
Other
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 96 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Corrosion
CODE Service Temp. Range Class Standard
Allowance
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
Up to 38 1480
50 1453
90 1372
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use nipple THD X Plain and threaded cap (TAM-01 and TAM-15) after blocking drains and vents.
6 Isolating joint see drawing on the appendix 15.
7 Use pipes, fittings and flanges of 2"and 3" with Sch 40 onshore.
8 All pipes shall be organic coated according appendix 18.
9 For on shore facilities only.
10 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
11 Impact test requirements according API 5L standard.
12 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 97 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC _____ 600 E14
Pipes and Fittings (Polyethilene coated, according to appendix 13) Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
Size Description Tag
T-05A 1" - 1 1/2" PLAIN
Ball valve; class 600; FLG; RTJ;
1" - 1 1/2" VE-46
API 5L Gr B PSL 1 seamless carbon steel.
Pipe
T-02A 2" - 10" Sch 80 Ball valve; class 600; FLG; RTJ; VE-13
(Note 7) 2" - 4"
BW carbon steel. VE-20
Cap TAM-05
Union UN-04
(Notes 1, 4 and 7)
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
Cross CRUZ-02
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
CLIENT: SHEET:
E&P 98 of 192
TITLE:
Temp. Corrosion
CODE Service Class Standard
Range Allowance
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC _____ 600 E14
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1480
50 1453
70 1412
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 Isolating joint see drawing on the appendix 15.
9 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
10 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
E&P 99 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Temp. Corrosion
CODE Service Class Standard
Range Allowance
3/4" SCH 40S 0,113" Ball valve; class 800; SW; duplex
T-36 PLAIN 1/2" - 1 1/2" VE-221
1" SCH 40S 0,133" steel, Devlon® V seat.
1 1/2" SCH 40S 0,145" Ball valve; class 600; FLG; RTJ;
ASTM A 790 (UNS S31803) 2" - 4" VE-222
2" SCH 10S 0,109" duplex steel, Devlon® V seat.
seamless
3" SCH 10S 0,120" Ball valve; class 600; FLG; RTJ; gear;
6" - 16" VE-223
Pipe T-37A 4" SCH 40S 0,237" duplex steel, Devlon® V seat.
6" SCH 40S 0,280" Ball valve; fire tested; class 800; SW;
1/2" - 1 1/2" VE-224
8" SCH 40S 0,322" BW duplex steel.
10" SCH 40S 0,365" Ball valve; fire tested; class 600;
2" - 4" VE-225
12" SCH 80S 0,500" ASTM A 928 (UNS S31803 class FLG; RTJ; duplex steel.
T-47 1 or 3)
14" SCH 80S 0,500" welded (E=1) Ball valve; fire tested; class 600;
6" - 16" VE-226
16" SCH 80S 0,500" FLG; RTJ; gear; duplex steel.
Elbow 90º JO-45 Ball valve; TFE/P; class 800; SW; VE-387
1/2" - 1 1/2"
Elbow 45º JO-46 duplex steel. (Note 12)
Equal Tee TE-38 Ball valve; TFE/P; class 600; FLG; VE-234
2" - 4"
(Notes 1 and 3)
Cross CRUZ-32 ASTM A 182 Gr F 51 Ball valve; TFE/P; class 600; FLG;
3000 SW 6" - 16" VE-235 (Note 12)
Half Coupling ML-18 (UNS S31803) RTJ; gear; duplex steel.
Red. Coupling LRE-16 Ball valve; fire tested; TFE/P; class VE-390
1/2" - 1 1/2" 1/2" - 1 1/2"
Cap TAM-35 800; SW; duplex steel. (Note 12)
Short Nip. ASTM A 790 (UNS S31803) Ball valve; fire tested; TFE/P; class VE-295
T-36 6" - 16"
Long Nip. seamless 600; FLG; RTJ; gear; duplex steel. (Note 12)
PLAIN
Red.Nip.C NIPRC-11
Fittings and Accessories
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
CLIENT: SHEET:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1499
50 1499
100 1469
110 1441
130 1387
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When requerid Fully Tight Valve (VET), see types in appendix 14.
10 For use gas inlet from Amine contactors and outlet gas K.0. drum for K.0. drum of compression unit.
11 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
12 Use only for AM - amine
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
13
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
14
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 0
CLIENT: SHEET:
0ºC/90ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (6,4mm) 600 E17
Pipes and Fittings (Notes 10 and 11) Valves (Note 9)
Size Wall or
Item Tag Ends Material Ball (Note 4)
(in) Class
Size Description Tag
T-05A 1" - 1 1/2" XXS PLAIN
Ball valve; class 800; SW; carbon steel,
1" - 1 1/2" VE-333D
2" XXS up to 110ºC.
API 5L Gr B PSL 1
3" - 4" Sch 160 Ball valve; class 600; FLG; RTJ; carbon VE-374
seamless 2" - 4"
T-02A 6" - 8" Sch 120 steel, up to 110ºC. VE-375
Pipe
10" - 12 0,812" Ball valve; class 600; FLG; RTJ; gear;
(Notes 10) 6" - 24" VE-376
14" 0,875" BW carbon steel, up to 110ºC.
Elbow 90º JO-37 Ball valve; fire tested; class 600; FLG;
6" - 24" VE-380
Elbow 45º JO-38 RTJ; gear; carbon steel.
Cross CRUZ-28
1" - 1 1/2" 9000 SW ASTM A 105
Half Coupling ML-14
Red. LRE-12
Cap TAM-33
Union UN-19
Coupling L-23
Fittings and Accessories (Notes 1 and 6)
Short Nip.
T-05A API 5L Gr B PSL 1 seamless
Long Nip.
1" - 1 1/2" PLAIN
Red.Nip.C NIPRC-04
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
Tee TE-02
Weldolet WOL-01 ASTM A 105 Gate valve; class 600; FLG; RTJ; gear;
8" - 24" VG-11
carbon steel.
Globe
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 90ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (6,4 mm) 600 E17
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 1480
50 1453
100 1351
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and
ASTM A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-57) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When requerid Fully Tight valve (VET), see types in appendix 14.
10 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
11 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 215ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 11).
(Note: 10)
___ 600 E30
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 9) Valves
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1/2" SCH 40S 0,109" Size Description Tag
3/4" SCH 40S 0,113" Inconel ®625 Ball valve; fire tested; class 800; FLG;
T-42 PLAIN 1/2" - 1 1/2" VE-463
1" SCH 80S XS 0,179" ASTM B444 (UNS N06625) RTJ; Inconel® 625; RPTFE®/metal seat.
1 1/2" SCH 80S XS 0,200" Ball valve; fire tested; class 600; FLG; VE-460
2" - 4" RTJ; carbon steel + Inconel® 625;
2" SCH 40 STD 0,154" RPTFE®/metal seat. VE-461
3" SCH 40 STD 0,216" Ball valve; fire tested; class 600; FLG;
6' - 16" RTJ; gear; carbon steel + Inconel® 625; VE-462
Pipe 4" SCH 40 STD 0,237" RPTFE®/metal seat.
6" SCH 40 STD 0,280" API 5L Gr B PSL 1
T-02A
8" SCH 80 XS 0,500" seamless
BW
10" SCH 80 0,594"
Union UN-29
Coupling L-33
PLAIN
Red. Nip. C NIPRC-16 Inconel ® 625
Red. Nip. E NIPRE-22 ASTM B564 (UNS N 06625)
Cap TAM-02
Cross CRUZ-02
Butterfly
Globe
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 215ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 11).
(Note: 10)
___ 600 E30
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
100 1354
150 1309
200 1268
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 Isolating joint see drawing on the appendix 15.
8 When required Fully Tight Valve (VET), see types in appendix 14.
9 All piping, fittings and valves shall be internal Inconel® 625 coated according Appendix 16.
10 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
11 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
-55ºC / 330ºC
ASME B31.3 PC (Corrosive Hydrocarbon) (Note 10).
(Note: 9)
___ 600 E32
Pipes and Fittings Coated with Inconel® 625 - (According appendix 16) (Note 8) Valves (Note 7)
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" Sch 160 0,188" Size Description Tag
3/4" Sch 160 0,219" Inconel ®625 Ball valve; fire tested; class 800; FLG;
T-42 PLAIN 1/2" - 1 1/2" VE-463
1" Sch 80S 0,179" ASTM B444 Gr1 (UNS N06625) RTJ; Inconel® 625; RPTFE®/metal seat.
1 1/2" Sch 80S 0,200" Ball valve; fire tested; class 600; FLG;
2" - 4" RTJ; ASTM A 350 Gr LF3 ; coated VE-486
Pipe 2" Sch 40S 0,154" Inconel® 625, RPTFE®metal seat.
3" Sch 40S 0,216" Ball valve; fire tested; class 600; FLG;
ASTM A 333 Gr 3 6" - 8" RTJ; gear; ASTM A 350 Gr LF3 ; coated VE-490
T-50 4" Sch 40S 0,237" BW Inconel® 625, RPTFE®/metal seat.
seamless
6" Sch 40S 0,280"
Union UN-29
Coupling L-33
Fittings and Accessories
Cap TAM-47
Cross CRUZ-48
Globe
Globe valve, class 600,FLG; RTJ,
2" - 8" ASTM A 350 Gr LF3 + Inconel® 625, VGL-101
fire tested, metal seat.
FLG-190 BLIND (RTJ) Inconel ® 625
1/2" - 1 1/2" 600
FLG-191 SW (RTJ) ASTM B564 (UNS N 06625)
Flange
FLG-200 BLIND (RTJ)
2" - 8" 600 ASTM A 350 Gr LF3
FLG-201 WN (RTJ) Check
JI-04 1" - 8" Oval Fenolic resin Check valve; dual plate; wafer; class
2" - 8" 600; RTJ; ASTM A 350 Gr LF3 + VR-156
Stud PAE-07 ASTM A 320 Gr L7 Inconel® 625, metal seat
1/2" - 1"
Nut (Note 2) ASTM A 194 Gr 4/S3 Other
Stud PAE-08 ASTM A 320 Gr L7 Globe valve, needle disc; 3000 PSI; SW;
1 1/8" 1/2" - 1 1/2" VAG-40
Nut (Note 2) ASTM A 194 Gr 4/S3 Inconel® 625.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
-55ºC / 330ºC
ASME B31.3 PC (Corrosive Hydrocarbon) (Note 10).
(Note: 9)
___ 600 E32
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
5 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping, fittings and valves shall be internal Inconel® 625 coated according Appendix 16.
9 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
10 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156
(NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Pipe
4" - 10" SCH 120 ASTM A 358 Gr TP 316L CL 1 or 3 Ball valve; class 1500; SW; stainless
T-34 (Note 10) BW 1 1/2" VE-237B
welded (E=1) steel, PEEK® seat, up to 150ºC.
Short Nip. ASTM A 312 Gr TP 316L Ball valve; PEEK® seat, class 1500;
T-33 2" VE-272
Long Nip. seamless FLG; RTJ; 150ºC to 200ºC.
PLAIN
Red.Nip.C NIPRC-14 Ball valve; PEEK® seat, class 900;
Fittings and Accessories
S.R.ELL 90º CRC-25 Ball valve; fire tested; class 1500; SW;
Wall 1/2" - 1" stainless steel, PEEK® seat, up to VE-275
L.R.ELL 90º CRL-35 thickness 150ºC.
L.R.ELL 45º CRL-36 according to ASTM A 403 Gr WP 316L Ball valve; fire tested; class 1500; SW;
pipe 1 1/2" stainless steel, PEEK® seat, up to VE-275B
Tee TE-46 150ºC.
Red. Tee TRE-41 Ball valve; fire tested; class 900; FLG;
2" - 18" BW 2" RTJ; stainless steel, Devlon® V seat, VE-277
Conc. Red. REDC-18 up to 150ºC.
Ecc. Red. REDE-17 Ball valve; fire tested; class 900; FLG;
3" - 4" RTJ; stainless steel, Devlon® V seat, VE-278
Cap TAM-49 up to 150ºC.
Cross CRUZ-41 Ball valve; fire tested; class 900; FLG;
6" - 18" RTJ; gear; stainless steel, Devlon® V VE-279
Weldolet WOL-10 ASTM A 182 Gr F 316L seat, up to 150ºC.
Ball valve; fire tested; class 1500; SW;
1/2" - 1" stainless steel, PEEK® seat, 150ºC to VE-280
200ºC.
Ball valve; fire tested, class 1500; SW;
1 1/2" stainless steel, PEEK® seat, 150ºC to VE-280B
200ºC.
Ball valve; fire tested, class 900; FLG;
2" RTJ; stainless steel, PEEK® seat,150ºC VE-282
to 200ºC.
Ball valve; fire tested, class 900; FLG;
3" - 4" RTJ; stainless steel, PEEK® seat, VE-283
150ºC to 200ºC.
Ball valve; fire tested, class 900; FLG;
6" - 18" RTJ; gear; stainless steel, PEEK® seat, VE-284
150ºC to 200ºC.
Gate (Note 3)
Globe
FLG-176 1/2" - 1 1/2" SW (RTJ) Globe valve; class 900; FLG; RTJ;
6" - 10" VGL-14E
FLG-174 2" 1500 WN (RTJ) gear; stainless steel.
Flange FLG-175 1/2" - 2" BLIND (RTJ) ASTM A 182 Gr F 316L Check
(Note 5)
FLG-173 BLIND (RTJ) Check valve, horizontal piston; class
3" - 18" 900 1/2" - 1 1/2" VR-145
FLG-172 WN (RTJ) 1500; SW; stainless steel.
JA-07 1/2" - 2" 1500 Check valve, dual plate; wafer; class
Stainless steel AISI 316L max.
2" 1500, RTJ; stainless steel; Viton TBR-S VR-47
JA-15 3" - 18" 900 hardness 150 Brinell
Gasket seat.
Octagonal
(Note 9) JI-05 1/2" - 2" 1500 Check valve, dual plate; wafer; class
Fenolic resin 3" - 10" 900, RTJ; stainless steel; Viton TBR-S VR-46
JI-04 3" - 18" 900 seat.
Stud PAE-07 ASTM A320 Gr L7 Other
1/2" - 1 "
Nut (Note 8) ASTM A194 Gr 4/S3
Globe valve, needle disc; 3000 PSI,
Stud PAE-08 ASTM A320 Gr L7 1/2" - 1 1/2" VAG-45
1 1/8" - 1 7/8" SW, stainless steel.
Nut (Note 8) ASTM A194 Gr 4/S3
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 2160
50 2093
100 1836
150 1675
200 1552
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 For onshore facilities only, stub in connections may be used according to ASME B31.3.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Use according appendix 5.
7 When required Fully Tight valve (VET), see types in appendix 14.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 Isolating joint see drawing on the appendix 15.
10 From -100°C to -30°C material shall be solution heat-treaded.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 350 ºC
ASME B31.3 S-Steam; SC-Steam Condensate
(Note: 11)
(1,6mm) 900 F4
Pipes and Fittings Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
1/2" - 3/4" Sch 160 Size Description Tag
T-05A PLAIN API 5L Gr B PSL 1 seamless
1" - 1 1/2"
Sch 80
2" - 3" API 5L Gr B PSL 1 seamless or
Pipe T-02A/T-02B welded
4" - 10" ERW or ERW / HFIW
BW
Sch 120 API 5L Gr B PSL 1 welded
T-02B 12" - 18"
(E=0,85)
Red.Nip.C NIPRC-04A
1/2" - 4"' BW/PLAIN
Red .Nip.E NIPRE-10A
Cross CRUZ-02
Check
Check valve; horizontal piston;
1/2" - 1 1/2" VR-03
class 1500; SW; carbon steel.
Gasket JA-02 1/2" - 2" 1500 Octagonal Carbon steel coated Zn-Ni max.
(Notes 2 and 10) JA-01 3" - 18" 900 Oval hardness 90 Brinell
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
150 1960
200 1905
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Use only downstream centrifuge.
8 Use only downstream filters.
9 Use according appendix 5.
10 Isolating joint see drawing on the appendix 15.
11 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
12 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Tee TE-02
Cap TAM-02
Cross CRUZ-02
Gate
Gate valve; abrasive; FLG; RTJ;
2 1/16" - 4
carbon steel; API 3000 PSI; VG ABRAS-05
1/16"
CWP.
Globe
Check
Check valve; dual plate; wafer;
2" class 1500; RTJ; carbon steel; VR-40
Viton seat.
Check valve; dual plate; wafer;
3" - 6" class 900; RTJ; carbon steel; VR-39
Viton seat.
Gasket JA-02 2" 1500 Octagonal Carbon steel coated Zn-Ni max.
(Note 2) JA-01 3" - 6" 900 Oval hardness 90 Brinell Other
Stud PAE-01 ASTM A 193 Gr B7
7/8" - 1"
Nut (Note 2) ASTM A 194 Gr 2H
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 2221
50 2181
90 2058
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-16 or FLG-18 will be used as a counter flange of VG ABRAS-04 (FJA).
5 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
6 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
14" 0,938"
ASTM A671 Gr CC 60 CL 22
T-08 16" 1.062"
welded (E=1)
Elbow 90º JO-17
Cross CRUZ-12
6000 SW ASTM A 350 Gr LF2 CL 1
Half Coupling ML-07
(Notes 1 and 5)
PLAIN
Red.Nip.C NIPRC-05
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red .Nip.E NIPRE-16A Globe
S.R.ELL 90º CRC-02 Globe valve; class 1500; FLG; RTJ;
Wall 2" VGL-28
L.R.ELL 90º CRL-03 carbon steel.
thickness
L.R.ELL 45º CRL-04 according to
Globe valve; class 900; FLG; RTJ;
pipe ASTM A 420 Gr WPL 6 3" - 4" VGL-29
Tee TE-08 carbon steel.
Cap TAM-08
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 F
CLIENT: SHEET:
Temp. Corrosion
CODE Service Class Standard
Range Allowance
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46 to 38 2221
50 2181
100 2027
130 2207
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tignt valve (VET), see types in appendix 14.
9 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156
(NACE MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Union UN-09
Coupling L-09
PLAIN
Red.Nip.C NIPRC-05 Gate
Red.Nip.E NIPRE-16
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-16A
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 A
CLIENT: SHEET:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-46 / 38 1770
110 1770
Notas:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 E
CLIENT: SHEET:
3/4" SCH 160 0,219" Ball valve; class 1500; SW; carbon
T-05A PLAIN API 5L Gr B PSL 1 seamless 1/2" - 3/4" VE-415C
1" SCH 160 0,250" steel; PEEK® seat, up to 150°C.
1 1/2" SCH 160 0,281" Ball valve; class 1500; SW; carbon
1" - 1 1/2" VE-415B
2" SCH 80 XS 0,218" steel; PEEK® seat, up to 150°C.
API 5L Gr B PSL 1 seamless or
3" SCH 80 XS 0,300" Ball valve; class 1500; FLG; RTJ;
welded
T-02A/T-02B 2" carbon steel; Devlon® V seat, up to VE-416
ERW or ERW / HFIW
Pipe 4" SCH 120 0,438" 150°C.
(E=0,85) (Note 14)
(Note 11) 6' SCH 120 0,562" Ball valve; class 900; FLG; RTJ; carbon VE-417
3" - 4"
8" SCH 120 0,719" steel; Devlon® V seat, up to 150°C. VE-418
BW API 5L Gr X65 PSL 2
10" SCH 120 0,844" Ball valve; class 900; FLG; RTJ; gear;
T-46 seamless 6" - 18" carbon steel; Devlon® V seat, up to VE-419
SCH 120 XXS
12" 150°C.
1,000"
14" SCH 120 1,094" Ball valve; class 1500; SW; carbon
API 5L Gr X65 PSL 2 1/2" - 3/4" VE-420C
16" 1,125" welded (E=1) steel, PEEK® seat, over 150°C.
T-45
18" 1,188" Ball valve; class 1500; SW; carbon
1" - 1 1/2" VE-420B
Elbow 90º JO-09 steel, PEEK® seat, over 150°C.
Red. Tee TRE-03 Ball valve; class 900; FLG; RTJ; carbon VE-422
3" - 4"
Cross CRUZ-06 steel, PEEK® seat, over 150°C. VE-423
6000 SW ASTM A 105
(Notes 1 and 6)
Weldolet WOL-01 ASTM A 105 Ball valve; fire tested; class 1500;
6" - 18" FLG; RTJ; gear; carbon steel, PEEK® VE-434
seat, over 150ºC.
Gate (Note 5)
Gate valve; class 1500; SW; carbon
1/2" - 1 1/2" VG-46
steel.
JA-02 1/2" - 2" 1500 Octagonal Carbon steel coated Zn-Ni Globe valve; class 900; FLG; RTJ;
6" - 10" VGL-08E
JA-01 3" - 18" 900 max. hardness 90 Brinell gear; carbon steel.
Gasket
(Notes 2 and 9) JI-05 1/2" - 2" 1500 Oval Check
Fenolic resin
JI-04 3" - 18" 900 Check valve; horizontal piston; class
1/2" - 1 1/2" VR-03
Stud ASTM A 193 Gr B7 1500; SW; carbon steel.
PAE-01
3/4" - 1"
Nut (Note 2) ASTM A 194 Gr 2H Check valve; dual plate; wafer; class
2" VR-40
Stud ASTM A 193 Gr B7 1500; RTJ; carbon steel; Viton seat.
PAE-02 1 1/8" - 1
Nut (Note 2) 7/8" ASTM A 194 Gr 2H Check valve; dual plate; wafer; class
3" - 18" VR-39
Stud PAE- 09 ASTM A 193 Gr B16 900; RTJ; carbon steel; Viton seat.
(Notes 2 and 3/4" - 1"
Nut 4) ASTM A 194 Gr 7 Other
Stud PAE- 10 ASTM A 193 Gr B16
1 1/8" - 1 Globe valve, needle disc; 3000 PSI;
(Notes 2 and 1/2" - 1 1/2" VAG-17
Nut 7/8" ASTM A 194 Gr 7 SW; carbon steel.
4)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
100 2027
150 1960
200 1905
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 Gr B16 stud bolts
and ASTM A194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Use only in onshore installations.
9 Isolating joint see drawing on the appendix 15.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Impact test requirements according API 5L standard.
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156
13
(NACE MR0175)
14 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Equal Tee TE-06 Ball valve; class 900; FLG; RTJ; VE-14
3" - 4"
Red. Tee TRE-03 carbon steel. VE-21
Half Coupling ML-03 1/2" - 1 1/2" Ball valve; fire tested; class 1500;
1/2" - 3/4" VE-102C
(Notes 1 and 6)
Short Nip. API 5L Gr B PSL 1 Ball valve; fire tested; class 1500;
T-05A 2" VE-108
Long Nip. seamless FLG; RTJ; carbon steel.
Red.Nip.C NIPRC-04 PLAIN VE-107
Ball valve; fire tested; class 900; FLG;
3" - 4"
Red .Nip.E NIPRE-10 RTJ; carbon steel. VE-119
Wall
L.R.ELL 90º CRL-01 Gate valve; class 1500; SW; carbon
thickness 1/2" - 1 1/2" VG-46
ASTM A 234 Gr WPB steel.
L.R.ELL 45º CRL-02 according to
pipe
Tee TE-02 Gate valve; class 1500; FLG; RTJ;
2" VG-14
Red. Tee TRE-01 carbon steel.
2" - 18" BW
Conc. Red. REDC-01 Gate valve; class 900; FLG; RTJ;
3" - 6" VG-12
Ecc. Red. REDE-01 carbon steel.
Check
Check valve; horizontal piston; class
1/2" - 1 1/2" VR-03
FLG-43 1/2" - 1 1/2" SW (RTJ) 1500; SW; carbon steel.
FLG-18 2" 1500 WN (RTJ) Check valve; dual plate; wafer; class
Flange 2" VR-40
FLG-19 1/2" - 2" BLIND (RTJ) ASTM A 105 1500; RTJ; carbon steel; Viton seat.
(Note 7)
FLG-16 WN (RTJ) Check valve; dual plate; wafer; class
3" - 18" 900 3" - 18" VR-39
FLG-17 BLIND (RTJ) 900; RTJ; carbon steel; Viton seat.
JA-02 1/2" - 2" 1500 Octagonal Carbon steel coated Zn-Ni max.
JA-01 3" - 18" 900 hardness 90 Brinell
Gasket
(Notes 2 and 8) JI-05 1/2" - 2" 1500 Oval Other
Fenolic resin
JI-04 3" - 18" 900 Globe valve, needle disc; 3000 PSI;
1/2" - 1 1/2" VAG-17
Stud PAE-01 ASTM A 193 Gr B7 SW; carbon steel.
3/4" - 1 "
Nut (Note 2 ) ASTM A 194 Gr 2H
Stud PAE-02 1 1/8" - 1 ASTM A 193 Gr B7
Nut (Note 2 ) 7/8" ASTM A 194 Gr 2H
Stud PAE-09 ASTM A 193 Gr B16
3/4" - 1 "
Nut (Notes 2 and ASTM A 194 Gr 7
Stud PAE-10 1 1/8" - 1 ASTM A 193 Gr B16
Nut (Notes 2 and 7/8" ASTM A 194 Gr 7
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 A
CLIENT: SHEET:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
até 38 1770
110 1770
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and
ASTM A194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
10 Impact test requirements according API 5L standard.
11 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 90ºC
ASME B31.3 PCW-Produced water
(Note 7)
______ 900 F11
Pipes and Fittings (Organic coated - according appendix 18) Valves (Organic coated - according appendix 18)
Size Wall or
Item Tag Ends Material Ball
(in) Class
Size Description Tag
API 5L Gr B PSL 1 Ball valve; class 1500; FLG; RTJ;
T-05A 1" - 1 1/2" PLAIN
Sch 80 seamless 1" - 1 1/2" carbon steel; PEEK® seat; oganic VE-186D
coating
Pipe 2" - 3" API 5L Gr B PSL 1
Ball valve; class 1500; FLG; RTJ;
seamless or welded
T-02A/T-02B 2" carbon steel; PEEK® seat; oganic VE-187
4" - 10" ERW or ERW / HFIW
BW coating
Sch 120 (E=0,85) (Note 8)
API 5L Gr B PSL 1
T-02B 12" - 18" Ball valve; class 900; FLG; RTJ; carbon VE-189
welded (E=0,85) 3" - 4"
steel; PEEK® seat; oganic coating
Elbow 90º JO-09 VE-190
Elbow 45º JO-10 Ball valve; class 900; FLG; RTJ; gear;
6" - 18" carbon steel; PEEK® seat; oganic VE-191
Tee TE-06 coating
Red. Tee TRE-03
Cross CRUZ-06
(Notes 1 and 5)
Cap TAM-06
Union UN-05
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
Globe
0ºC / 90ºC
ASME B31.3 PCW-Produced water
(Note 7)
______ 900 F11
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
até 38 2221
50 2181
90 2058
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
7 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
8 The requirements for pipes produced by longitudinal electric welding seam shall be according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
CLIENT: SHEET:
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC ______ 900 F14
Pipes and Fittings (Coated with polyethylene, according to appendix 13) Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 1" - 1 1/2" PLAIN Size Description Tag
Sch 80 API 5L Gr B PSL 1
2" - 3" Ball valve; class 1500; FLG; RTJ; carbon
T-02A seamless 1" - 1 1/2" VE-47
4" - 10" Sch 120 steel.
Pipe
12" 1,000"
(Note 7) BW
14" 1,094" API 5L Gr BN PSL 2 Ball valve; class 1500; FLG; RTJ; carbon
T-51 2" VE-15
16" 1,219" welded (E=0,95) steel.
18" 1,375"
Elbow 90º JO-09 Ball valve; class 900; FLG; RTJ; carbon VE-14
3" - 4"
Elbow 45º JO-10 steel. VE-21
Equal Tee TE-06 Ball valve; class 900; FLG; RTJ; gear;
6" - 18" VE-26
Red. Tee TRE-03 carbon steel.
Cross CRUZ-06
6000 SW ASTM A 105
Half Coupling ML-03
Union UN-05
Fittings (notes 1, 4 and 7)
Coupling L-05
Check
Gasket JA-02 1" - 2" 1500 Octagonal Carbon steel coated Zn-Ni max.
(Notes 6 and 8) JA-01 3" - 18" 900 Oval hardness 90 Brinell
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
CLIENT: SHEET:
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC ______ 900 F14
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 2221
50 2181
70 2119
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 Isolating joint see drawing on the appendix 15.
9 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
10 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 70ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 5 and 13) _______ 900 F16
Pipes and Fittings (Note 7) Valves (Notes 8 and 9)
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" SCH 40S 0,109" Size Description Tag
3/4" SCH 40S 0,113" Ball valve; class 1500; SW; duplex
T-36 PLAIN 1/2" - 1 1/2" VE-227
1" SCH 40S 0,133" steel, RTJ .
1 1/2" SCH 40S 0,145" Ball valve; class 1500; FLG; RTJ;
ASTM A 790 (UNS S31803) 2" VE-228
2" SCH 40S 0,154" duplex steel, PEEK® seat.
seamless
3" SCH 40S 0,216" Ball valve; class 900; FLG; RTJ;
3" - 4" VE-475
Pipe T-37A 4" SCH 40S 0,237" duplex steel, .
6" SCH 40S 0,280" Ball valve; class 900; FLG; RTJ; gear;
6" - 16" VE-476
8" 0,375" BW duplex steel, RTJ.
10" SCH 80S 0,500" Ball valve; fire tested; class 1500;
1/2" - 1 1/2" VE-440
12" SCH 60 0,562" ASTM A 928 (UNS S31803 class SW; duplex steel.
T-47 1 or 3)
14" 0,625" welded (E=1) Ball valve; fire tested; class 1500;
2" VE-441
16" 0,750" FLG; RTJ; duplex steel, PEEK® seat.
Union UN-23
Coupling L-27
Cap TAM-36
Cross CRUZ-33
FLG-130 2" 1500 BLIND (RTJ) Globe valve; class 900; FLG; RTJ;
Flange ASTM A 182 Gr F 51 6" - 8" VGL-99
FLG-131 1/2" -2" WN (RTJ) gear; duplex steel.
(Note 4) (UNS S31803)
FLG-193 BLIND (RTJ)
3" - 16" 900
FLG-194 WN (RTJ)
0ºC / 70ºC
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Notes 5 and 13) _______ 900 F16
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 2250
50 2250
70 2204
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-37) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When requerid Fully Tight Valve (VET), see types in appendix 14.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 Use only for AM - amine
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
12
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
13
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
-55ºC / 320ºC
ASME B31.3 PC (Corrosive Hydrocarbon) (Note 10).
(Note: 9)
___ 900 F32
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 8) Valves
Size
Item Tag Wall or Class Ends Material Ball
(in)
1/2" Sch 80S 0,179" Size Description Tag
3/4" Sch 80S 0,200" Inconel ®625 Ball valve; fire tested; class 1500; SW;
T-42 PLAIN 1/2" - 1 1/2" VE-487
1" Sch 80 0,179" ASTM B444 Gr1 (UNS N06625) RTJ; Inconel® 625; metal seat.
1 1/2" Sch 80 0,200" Ball valve; fire tested; class 1500; FLG;
2" RTJ; ASTM A 350 Gr LF3 + Inconel® VE-491
2" Sch 40S 0,154" 625; metal seat.
3" Sch 40S 0,216" Ball valve; fire tested; class 900; FLG;
3" - 4" RTJ; ASTM A 350 Gr LF3 + Inconel® VE-488
Pipe 4" Sch 40S 0,237" 625; metal seat.
6" 0,312" Ball valve; fire tested; class 900; FLG;
ASTM A 333 Gr 3
T-50 6" - 16" RTJ; gear; ASTM A 350 Gr LF3 + VE-489
8" Sch 60 0,406" BW seamless
Inconel® 625; metal seat.
10" Sch 40S 0,500"
14" 0,625"
ASTM A 333 Gr 3
T-54 16" 0,750"
Welded (E=1)
Elbow 90º JO-54
Union UN-29
Coupling L-33
N06625)
PLAIN
Red. Nip. C NIPRC-16 Inconel ® 625
Red. Nip. E NIPRE-22 ASTM B564 (UNS N 06625) Globe
Red. Nip. C NIPRC-22 Globe valve; class 1500; FLG; RTJ;
1/2" - 4" BW/PLAIN ASTM A420 Gr WPL3 (Note 9) 2" carbon steel; ASTM A 350 Gr LF3 + VGL-102
Red. Nip. E NIPRE-29 Inconel, class 1500
S.R. ELL 90º CRC-28 Globe valve; class 900; FLG; RTJ; carbon
3" - 4" steel; ASTM A 350 Gr LF3 + Inconel, VGL-103
L. R. ELL. 90º CRL-42 class 900
L. R. ELL. 45º CRL-43 Globe valve; FLG; RTJ; carbon steel;
Wall 6" - 16" gear; ASTM A 350 Gr LF3 + Inconel; VGL-103E
Tee TE-52 thickness class 900.
Red. Tee TRE-43 according to
2" - 16" pipe BW ASTM A420 Gr WPL3 (Note 9)
Conc. Red. REDC-17
Cross CRUZ-48
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
-55ºC / 320ºC
ASME B31.3 PC (Corrosive Hydrocarbon) (Note 10).
(Note: 9)
___ 900 F32
Pressure / Temperature Rating (1335)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
5 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
6 Isolating joint see drawing on the appendix 15.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping, fittings and valves shall be internal Inconel® 625 coated according Appendix 16.
9 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
10 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 F
CLIENT: SHEET:
3/4" 0,154" SCH 80S ASTM A 182 Gr F 316L Ball valve; class 1500; SW; stainless
T-33 PLAIN 1/2" - 1 1/2" VE-238B
1" 0,179" SCH 80S seamless steel, PEEK® seat.
1 1/2" 0,200" SCH 80S Ball valve; class 1500; FLG; RTJ;
2" - 3" VE-435
2" 0,250" stainless steel, PEEK® seat.
3" 0,438" SCH 160 Ball valve; class 1500; FLG; RTJ; gear;
4" - 16" VE-436
stainless steel, PEEK® seat.
Pipe 4" 0,531" SCH 160
6" 0,719" SCH 160 Ball valve; fire tested, class 1500; SW;
T-34 ASTM A 358 Gr TP 316L 1/2" - 1 1/2" VE-285B
8" 0,906" SCH 160 BW stainless steel, PEEK® seat.
(Note 8) CL 1 or 3 welded (E=1)
10" 1,125" SCH 160 Ball valve; fire tested, class 1500; FLG;
2" - 3" VE-287
12" 1,312" SCH 160 RTJ; stainless steel, PEEK® seat.
14" 1,406" SCH 160 Ball valve; fire tested, class 1500; FLG;
4" - 16" VE-288
16" 1,594" SCH 160 RTJ; gear; stainless steel, PEEK® seat.
Cross CRUZ-40
1/2" - 1 1/2" 3000 SW ASTM A 182 Gr F 316L
(Notes 1 and 5)
Cap TAM-38
Union UN-25
Coupling L-29
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION
DR-ENGP-1.1 F
CLIENT: SHEET:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
100 3060
150 1792
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-18) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 When requerid Fully Tight Valves (VET), see types in appendix 14.
8 From -100°C to -30°C material shall be solution heat-treated.
9 Isolating joint see drawing on the appendix 15.
10 Maximum working pressure.
14" - 2.930 psi
16" - 2.905 psi
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
10" 1.125"
Cross CRUZ-06
6000 SW ASTM A 105
Half Coupling ML-03
Red.Nip.E NIPRE-10
Red.Nip.C NIPRC-04A
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-10A
Cap TAM-02
Other
FLG-43 1/2" - 1 1/2" SW (RTJ) Globe valve, needle disc, 5000 PSI, SW,
Flange 1/2"- 1 1/2" VAG-18
FLG-18 2" - 10" 1500 WN (RTJ) ASTM A 105 carbon steel .
(Note 5)
FLG-19 1/2" - 10" BLIND (RTJ)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
150 3269
200 3176
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
7 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 90ºC
ASME B31.3 FP-Production and drilling fluid
(Note:5)
(3,2 mm) 1500 G5
Pipes and Fittings Valves
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 3/4" XXS PLAIN Size Description Tag
6" XXS
Tee TE-02
Globe
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 3702
50 3634
90 3430
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-18 will be used as a counter flange of VG ABRAS-04 (FJA).
5 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
3" Sch 160 0,438" ASTM A 333 Gr 6 Ball valve; class 1500; FLG; RTJ;
4" - 16" VE-99
4" Sch 160 0,531" seamless gear; carbon steel.
Pipe
6" XXS 0,864
T-07A
8" 1.000" BW
10" 1.250"
Cross CRUZ-12
SW ASTM A 350 Gr LF2 CL 1
Half Coupling ML-07
6000
Fittings and Accessories (Notes 1 and 5)
Union UN-09
Coupling L-09
Red.Nip.E NIPRE-16
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-16A
Cross CRUZ-08
Weldolet WOL-02
Check
Check valve; horizontal piston;
1/2" - 1 1/2" VR-58
class 1500; SW; carbon steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46/38 3702
50 3634
100 3379
110 3357
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC/-15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 Maximum working pressure.
12" -3.653 psi
14" - 3.573 psi
16" - 3.567 psi
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Cross CRUZ-12
(Notes 1 and 5)
Union UN-09
Coupling L-09
T-09
Long Nip. seamless
PLAIN
Red.Nip.C NIPRC-05 Gate
Red.Nip.E NIPRE-16
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-16A
Check
Other
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 A
CLIENT: SHEET:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46/38 2650
110 2650
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC/-15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
24" SCH 140 2,062" Ball valve; fire tested; class 1500;
4" - 24" FLG; RTJ; gear; carbon steel, PEEK® VE-394
Elbow 90º JO-09 seat.
Elbow 45º JO-10
Cross CRUZ-06
6000 SW ASTM A 105
Coupling L-05
Cap TAM-06
Union UN-05
Short Nip.
Fittings and Accessories (Notes 1 and 6)
Tee TE-02
Red. Tee TRE-36 8" - 24" ASTM A 694 Gr F65 (Note 8) Check valve; dual plate; wafer; class
2" - 24" 1500; RTJ; carbon steel; Viton TBR-S VR-40
Conc. Red. REDC-14 seat.
Ecc. Red. REDE-13
Cap TAM-43
Cross CRUZ-27
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-20 to 38 3705
50 3634
100 3379
150 3269
200 3176
210 3149
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts and ASTM
A194 GR 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
9 Use only in onshore installations.
10 Isolating joint see drawing on the appendix 15.
11 When requerid Fully Tight valve (VET), see types in appendix 14.
12 Impact test requirements according API 5L standard.
13 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 110ºC
ASME B31.4/ASME B31.8 P-Process (Non-corrosive Hydrocarbon) (1,6mm) 1500 G10P
Pipes and Fittings Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball (Note 3)
(in) Class
1/2" SCH 160 0,188" Size Description Tag
3/4" SCH 160 0,219" API 5L Gr B PSL 1 Ball valve; fire tested; class 1500;
T-05A PLAIN 1/2" - 1 1/2" VE-102D
1" SCH 80 XS 0,179" seamless SW; carbon steel.
1 1/2" SCH 160 0,281" Ball valve; fire tested; class 1500;
4" VE-108P
4" - PIGGABLE SCH 80 XS 0,337" FLG; RTJ; carbon steel (Piggable).
6" - PIGGABLE SCH 80 XS 0,432" Ball valve; fire tested; class 1500;
API 5L Gr X65 PSL 1 6" - 24" FLG; RTJ; gear; carbon steel VE-126P
Pipe 8" - PIGGABLE SCH 100 0,594" seamless (Piggable).
T-38A
(Note 9) 10" - PIGGABLE SCH 100 0,719" (Note 8 )
Cross CRUZ-06
6000 SW ASTM A 105
Half Coupling ML-03
1/2" - 1 1/2
Red. Coupling LRE-02
Cap TAM-06
Fittings and Accessories
Union UN-05
Coupling L-05
Check
FLG-43 SW (RTJ)
1/2" - 1 1/2" ASTM A 105
FLG-19 BLIND (RTJ)
Flange 1500
FLG-161 WN (RTJ) ASTM A 694 Gr F 65
(Note 5) 4" - 24"
FLG-162 BLIND (RTJ) (Nota 8)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
0ºC / 110ºC
ASME B31.4/ASME B31.8 P-Process (Non-corrosive Hydrocarbon) (1,6mm) 1500 G10P
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
0/38 3702
70 3532
110 3357
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Isolating joint see drawing on the appendix 15.
7 When required Fully Tight valve (VET), see types in appendix 14.
8 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
9 For 3d and 5d bends the maximum wall thickness thinning shall be 15% and 10%, respectively. This bend´s shall be piggable.
10 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Union UN-05
Short Nip.
T-05A API 5L Gr B PSL 1 seamless
Long Nip.
PLAIN
Red.Nip.C NIPRC-04
Fittings and Accessories
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-20 to 38 2650
110 2650
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A193 GR B16 stud bolts
and ASTM A194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Isolating joint see drawing on the appendix 15.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Cross CRUZ-06
6000 SW ASTM A 105
Coupling L-05
Cap TAM-06
Red. Nip. C NIPRC-04A Gate valve; class 1500; FLG; RTJ; gear;
1" - 4" BW/PLAIN 6" - 24" VG-75
Red. Nip. E NIPRE-10A carbon steel, organic coating.
Tee TE-02
Cap TAM-28
Cross CRUZ-25
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
up to 38 3702
50 3634
90 3430
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
4
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
9 Isolating joint see drawing on the appendix 15.
10 When required Fully Tight valve (VET), see types in appendix 14.
11 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 D
CLIENTE: SHEET:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) 0ºC / 90ºC ____ 1500 G12
Pipes and Fittings (Note 7) Valves (Notes 8 and 9)
Size Wall or
Item Tag Ends Material Ball
(in) class
T-17 1/2" - 1 1/2" PLAIN Size Description Tag
Sch 40S
2" - 3" ASTM A 790 (UNS S32760) Ball valve; class 1500; SW; superduplex
1/2" - 1 1/2" VE-168
T-19 4" 0.281" seamless stainless steel.
6" - 8" Sch 80S Ball valve; class 1500; FLG; RTJ; superduplex
2" - 4" VE-169
10" 0.719" stainless steel.
Pipe 12" 0.875" Ball valve; class 1500; FLG; RTJ; gear;
BW 6" - 24" VE-170
14" 0.938" superduplex stainless steel.
ASTM A 928 (UNS S32760 class
T-49 16" 1.062" 1 or 3) Ball valve; fire tested; class 1500; SW ;
welded (E=1) 1/2" - 1 1/2" VE-171
18" 1.250" superduplex stainless steel.
20" 1.375" Ball valve; fire tested; class 1500; FLG; RTJ;
2" - 4" VE-172
24" Sch 120 superduplex stainless steel.
Elbow 90º JO-35 Ball valve; fire tested; class 1500; FLG; RTJ;
6" - 24" VE-173
Elbow 45º JO-36 gear; superduplex stainless steel.
Union UN-18
Coupling L-22
S.R.ELL 90º CRC-06 Gate valve; class 1500; FLG; RTJ; gear;
14" - 24" VG-69
L.R.ELL 90º CRL-13 Wall superduplex stainless steel.
thickness ASTM A 815
L.R.ELL 45º CRL-14
according to (UNS S32760)
Tee TE-25 pipe
Cap TAM-27
Cross CRUZ-21
ASTM A 182 Gr F 55
Weldolet WOL-05
(UNS S32760)
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) 0ºC / 90ºC ____ 1500 G12
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
até 38 3750
50 3750
90 3689
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
3 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 This Spec should only be used when recommended in appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According Appendix 16 welding qualification requirements for superduplex.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 According appendix 17 - casting qualification requirements minimum for valves superduplex.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Cap TAM-29
Fittings and Accessories
Union UN-18
Coupling L-22
Short Nip.
T-17 PLAIN
Long Nip. Gate
Globe
Check
Other
FLG-109 SW (RTJ)
Flange 1/2" - 1 1/2" ASTM A 182 Gr F 55
FLG-110 BLIND (RTJ)
(Note 3) (UNS S32760)
FLG-111 4" - 14" WN (RTJ)
1500
Stainless steel AISI 316 max.
Gasket JA-07 Octagonal
1/2" - 14" Hardness 150 HB
(Note 5)
JI-05 Oval Fenolic Resin
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
até 38 3750
50 3750
90 3689
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
3 Flanges ≤ 1 1/2" may be used, if strictly necessary.
4 This Spec should only be used when recommended in appendix 5.
5 Isolating joint see drawing on the appendix 15.
6 According Appendix 16 welding qualification requirements for superduplex.
7 When required Fully Tight valve (VET), see types in appendix 14.
8 According appendix 17 - casting qualification requirements minimum for valves superduplex.
9 Up to SDV shall be used carbon steel API 5L Gr X 60 cladding with Inconel 625 (UNS N06625).
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC _____ 1500 G14
Pipes and Fittings (Coated with polyethylene, according to appendix 13) Valves (Note 8)
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-05A 1" - 1 1/2" XXS PLAIN Size Description Tag
12" 1.125"
18" 1,562"
Red.Nip.C NIPRC-04A
1" - 4" BW/PLAIN
Red .Nip.E NIPRE-10A
TECHNICAL SPECIFICATION
DR-ENGP-1.1 B
CLIENT: SHEET:
ASME B31.3 IW-Fresh And De-Aerated Sea Water Injection (Note 2) 0ºC / 70ºC _____ 1500 G14
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 3705
50 3632
70 3575
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use only in offshore installations.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
7 Piping, conections and fittings should be revested with polyethylene according appendix 13.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
10 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
2" - 4" Sch 80S ASTM A 790 (UNS S31803) Ball valve; class 1500; SW; duplex
1/2" - 1 1/2" VE-227
T-37A 6" Sch 80 XS seamless steel, PEEK® seat.
Short Nip. ASTM A 790 (UNS S31803) Gate valve; class 1500; FLG; RTJ;
T-36 6" - 24" VG-99
Long Nip. seamless gear; duplex steel.
PLAIN
Red.Nip.C NIPRC-11 Globe
Fittings and Accessories
Other
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 3750
50 3750
100 3674
110 3600
130 3460
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-46) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Short Nip.
T-36 PLAIN
Long Nip.
Globe
Check
Check valve; horizontal piston; class
1/2" - 1 1/2" 1500; SW; RTJ; duplex stainless VR-125
steel.
Check valve, wafer, dual plate; class
2" - 10" 1500; RTJ, duplex steel; Viton seat VR-126
TBR-S.
Other
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 3750
50 3750
100 3674
110 3600
130 3460
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 On piping subjected to water hammer or requesting gradual opening and closing only gate valves shall be used.
3 Use niple THD X PLAIN and threaded cap (TAM-46) after drains and vents blocking.
4 Flanges ≤ 1 1/2" may be used, if strictly necessary.
5 Use according appendix 5.
6 Isolating joint see drawing on the appendix 15.
7 According appendix 16 - Welding qualification requirements for superduplex and duplex steel.
8 According appendix 17 - Casting qualification requirements minimum for valves superduplex and duplex steel.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
11 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.8 P - Process (Gas Treatment Unit) 0ºC / 100ºC (1,6 mm) 1500 G18
(Notes 8 and 9)
Pipes and Fittings (Notes 8 and 9) Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball (Note 3)
(in) Class
T-05A 1 /2" - 1 1/2" Sch 160 PLAIN Size Description Tag
2" 0,281" Ball valve; class 1500; socket; carbon
1/2" - 1 1/2" VE-43D
3" - 6" Sch 160 API 5L Gr B PSL 1 steel, up to 110ºC.
T-02A seamless
Ball valve; class 1500; FLG; RTJ; carbon
8" - 10" Sch 140 2" - 3" VE-15
steel, up to 110ºC.
Pipe
(Notes 8 and 9) BW
Ball valve; class 1500; FLG; RTJ; gear;
12" 0,625" 4" - 8" VE-27
API 5L Gr X70 PSL 1 carbon steel, up to 110ºC.
T-39 welded (E=1)
24" 1,000" (Note 6)
Ball valve; fire tested; class 1500; FLG;
2" - 3" VE-108
30" 1,250" RTJ; carbon steel.
Elbow 90º JO-09 Ball valve; fire tested; class 1500; FLG;
4" - 12" VE-126
Elbow 45º JO-10 RTJ; gear; carbon steel.
Union UN-05
Short Nip. API 5L Gr B PSL 1 Gate
T-05A
Long Nip. seamless
Gate valve; class 1500; socket weld;
PLAIN 1/2" - 1 1/2" VG-46
Red. Nip. C NIPRC-04 carbon steel.
Red. Nip. E NIPRE-10 Gate valve; class 1500; FLG; RTJ; carbon
2" - 4" VG-14
Red. Nip. C NIPRC-04A steel.
1/2" - 4" BW/PLAIN
Red. Nip. E NIPRE-10A Gate valve; class 1500; FLG; RTJ; gear;
6" - 14" VG-15
S. R. ELL 90º CRC-01 carbon steel.
Red. Tee TRE-01 Globe valve; class 1500; FLG; RTJ; gear;
2" - 10" 4" - 8" VGL-09E
Conc. Red. REDC-01 Wall carbon steel.
thickness
Ecc. Red. REDE-01
according to
Cap TAM-02 pipe
Cross CRUZ-02 Check
Weldolet WOL-01 BW ASTM A 105 Check valve; horizontal; piston; class
1/2" - 1 1/2" VR-03
S. R. ELL 90º CRC-21 1500; socket; carbon steel.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.8 P - Process (Gas Treatment Unit) 0ºC / 100ºC (1,6 mm) 1500 G18
(Notes 8 and 9)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
Up to 38 3129
50 3030
100 2920
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
7 When required Fully Tight valve (VET), see types in appendix 14.
8 Pipes of NPD 30" and wall thickness of 1,250", max.pressure limited 3250 psi.
9 In order to attempt specific project requirements, max.pressure of 3200 psi for thickness to NPD 8", 10" and 24", based on
ASME B31.8 and indicated materials in spec each range, as below:
NPD Thickness Pressure
8" Sch 140 0,812
10" Sch 140 1,000 3200 psi
24" - 1,000
10 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) -46ºC / 70ºC (3.2 mm) 1500 G19
Pipes and Fittings Valves (Note 8)
Size Wall or
Item Tag Ends Material Ball
(in) Class
T-09 1/2" - 1 1/2" XXS PLAIN Size Description Tag
Union UN-27
Coupling L-31
Red.Nip.E NIPRE-16
Red.Nip.C NIPRC-05A
1/2" - 4" BW/PLAIN
Red.Nip.E NIPRE-16A
Cross CRUZ-08
Weldolet WOL-02
Check
Check valve; horizontal piston;
1/2" - 1 1/2" VR-58
class 1500; SW; carbon steel.
Other
Globe valve, needle disc; 5000 PSI,
1/2" - 1 1/2" VAG-23
FLG-48 1/2" - 1 1/2" SW (RTJ) SW, carbon steel.
Flange
FLG-34 2" - 10" 1500 WN (RTJ) ASTM A 350 Gr LF2 CL 1
(Note 7)
FLG-35 1/2" - 10" BLIND (RTJ)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) -46ºC / 70ºC (3,2 mm) 1500 G19
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-46/38 3705
50 3632
100 3363
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC/-15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight Valve (VET), see types in appendix 14.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3
CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
H-Hydraulic Fluid; P-Process (Non-Corrosive Hydrocarbon) (note 9)
-100ºC /
210ºC
_______ 2500 H3
(Note 6)
Pipes and Fittings (Note 6) Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball
(in) Class
1" SCH 160 0,250" ASTM A 312 Gr TP 316L Size Description Tag
T- 41
1 1/2" 0,400" SCH 160 seamless 1" Ball valve; class 2500; BW; stainless
VE-463C
2" 0,436" XXS 1 1/2" steel, PEEK® seat.
Pipe 3" 0,600" XXS Ball valve; class 2500; FLG; RTJ;
BW 2" - 3" VE-463D
(Note 6) 4" 0,674" XXS stainless steel, PEEK® seat.
T-34 ASTM A 358 Gr TP 316L
(Note 8) 6" 0,875" CL 1 or 3 welded (E=1)
Ball valve; class 2500; FLG; RTJ;
4" - 10" VE-479
8" 1,000" stainless steel, PEEK® seat.
Globe
Globe valve; class 2500; FLG; RTJ;
2" - 3" VGL-30
stainless steel.
Check
Check valve; horizontal piston; class
1" - 1 1/2" VR-146
2500; BW; stainless steel.
Other
Globe valve, needle disc; 5000 psi;
1" - 1 1/2" VAG-44
FLG-178 1" - 10" WN (RTJ) BW; stainles steel.
Flange FLG-177 1" - 10" 2500 BLIND (RTJ) ASTM A 182 Gr F 316L
(Note 5)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3
CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);
H-Hydraulic Fluid; P-Process (Non-Corrosive Hydrocarbon) (Note 9).
-100ºC /
210ºC
_______ 2500 H3
(Note 6)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
50 5815
100 5100
150 4653
200 4311
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
4 Use niple THD X PLAIN and threaded cap (TAM-18) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Maximum working pressure (-100ºC/210ºC).
8" - 3.180 psig
10" - 3.190 psig
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 From -100ºC to -30ºC material shall de solution heat-treated.
9 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175).
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 C
CLIENT: SHEET:
Tee TE-02
Cap TAM-02
Cross CRUZ-02
Gate
Globe
Check
Check valve; dual plate; wafer;
2" - 6" VR-41
class 2500; carbon steel; Viton seat.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 6170
50 6050
90 5600
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The flange FLG-(20) will be used as a counter flange of VG ABRAS-04 (FJA).
5 Maximum working pressure (0ºC/90ºC).
2" - 6000 psi
3" - 5900 psi
4" - 5150 psi
6" - 4550 psi
6 All nominal thickness were checked limits of low temperature, in accordance with the criteria of the standard ASME B31.3.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
10' 1,312"
12" 1,781"
Red.Nip.C NIPRC-19
1" - 4"
Wall thickness
Red.Nip.E NIPRE-26
according to BW
S.R.ELL 90º CRC-02 pipe Globe
L.R.ELL 90º CRL-03 Globe valve; class 2500; FLG; RTJ;
2" - 3" VGL-100
L.R.ELL 45º CRL-04 carbon steel.
Other
Globe valve, needle disc; 6000 PSI,
1" - 1 1/2" VAG-47
FLG-196 WN (RTJ) SW, carbon steel.
Flange
1" - 12" 2500 ASTM A 350 Gr LF2 CL 1
(Note 7) FLG-197 BLIND (RTJ)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (PSIG) Temp. (ºC) Max. Press. (PSIG)
-46up to 38 6170
100 5629
130 6130
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC/-15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 When required Fully Tight valve (VET), see types in appendix 14.
9 Maximum pipe working pressure (-46ºC/110ºC).
1" - 5.234 psi 3" - 5.903 psi
1 1/2" - 4.171 psi 4" - 5.166 psi
2" - 4.358 psi 6" - 4.566 psi
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
10 MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
TECHNICAL SPECIFICATION F
SHEET:
E&P 167 of 192
TITLE:
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Corrosion
CODE Service Temp. Range Class Standard
Allowance
3" XXS 0,600" Ball valve; class 2500; FLG; RTJ; carbon
2" - 3" VE-16
4" XXS 0,674" steel; soft seat.
Pipe BW
(Note 8 and 11) 6" XXS 0,864" Ball valve; class 2500; FLG; RTJ; gear;
API 5L X65 PSL 2 4" - 12" VE-28
T-46 8" SCH 160 0,906" carbon steel.
seamless (Note 10)
10" SCH 160 1,125" Ball valve; fire tested; class 2500; BW;
1" - 1 1/2" VE-446
12" SCH 160 1,312" carbon steel.
Red. Tee TRE-35 Ball valve; fire tested; class 2500; FLG;
ASTM A 105 4" - 12" VE-127
Cross CRUZ-34 RTJ; gear; carbon steel.
1" - 1 1/2"
Cap TAM-31 Ball valve; fire tested; class 2500; FLG;
14" MSJ; gear; carbon steel ; PEEK®/metal VE-484
Short Nip. API 5L Gr B PSL 1 seat.
T-02A
Long Nip. seamless
(Notes 1 and 6)
Red.Nip.C NIPRC-20
1" - 4"
Red .Nip.E NIPRE-27 Gate (Note 5)
S.R.ELL 90º CRC-01 Gate valve; class 2500; FLG; RTJ; carbon
2" - 4" VG-16
L.R.ELL 90º CRL-01 steel.
L.R.ELL 45º CRL-02 Gate valve; class 2500; FLG; RTJ; gear;
6" - 12" VG-17
Tee TE-02 ASTM A 234 Gr WPB carbon steel.
S.R.ELL 90º CRC-26 Globe valve; class 2500; FLG; RTJ; gear;
4" - 8" VGL-19E
L.R.ELL 90º CRL-39 carbon steel.
Cap TAM-43
Cross CRUZ-27
FLG-20 WN (RTJ) Other
1" - 6" ASTM A 105
Flange FLG-21 BLIND (RTJ) Globe valve, needle disc; 5000 psig; BW;
1" - 1 1/2" VAG-43
(Note 7) FLG-153 BLIND (RTJ) carbon steel.
8" - 12"
FLG-154 WN (RTJ)
ASTM A 694 Gr F65
Compact FLG-142 WN (MSJ)
Flange 14"
2500
( Notes 13 and 14) FLG-141 BLIND (MSJ)
Carbon steel coated Zn-Ni
Gasket JA-02 Octagonal
1" - 12" max. hardness 90 Brinell
(Note 2)
JI-05 Oval Fenolic resin
IX Seal Ring Carbon steel coated Zn-Ni
JVM-02 14" ___
(Note 13) max. hardness 90 Brinell
Stud PAE-01 ASTM A 193 Gr B7
3/4" - 1"
Nut (Notes 2) ASTM A 194 Gr 2H
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION 0 F
CLIENT: SHEET:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
-20 to 38 6171
50 6058
100 5631
150 5448
175 5357
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Use niple THD X PLAIN and threaded cap (TAM-15) after drains and vents blocking.
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8 Maximum working pressure (0ºC/175ºC).
2" - 6.009 psi 8" - 4.665 psi
3" - 5.903 psi 10" - 4.730 psi
4" - 5.166 psi 12" - 4.694 psi
6" - 4.566 psi 14" - 4.021 psi
9 When required Fully Tight Valve (VET), see types in appendix 14.
10 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
11 Impact test requirements according API 5L standard.
12 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
175)
13 Compact flange in accordance with NORSOK L-005.
14 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
REV:
TECHNICAL SPECIFICATION B
SHEET:
0ºC / 100ºC
ASME B31.4/ASME B31.8 P-Process (Non-corrosive Hydrocarbon) (Note 14). (1,6mm) 2500 H10P
Pipes and Fittings Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball (Note 3)
(in) Class
1" XXS 0,358" Size Description Tag
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION 0 B
CLIENT: SHEET:
0ºC / 100ºC
ASME B31.4/ASME B31.8 P-Process (Non-corrosive Hydrocarbon) (Note 14). (1,6mm) 2500 H10P
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
4 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6 Isolating joint see drawing on the appendix 15.
7 When required Fully Tight valve (VET), see types in appendix 14.
8 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
9 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
10 Compact flange in accordance with NORSOK L-005.
11 For 3d and 5d bends, the maximum wall thickness thinning shall be 15% and 10%, respectively. This bends shall be piggable.
12 Impact test requirements according API 5L standard.
13 Maximum working pressure
1" - 6.388 psi 6" - 4.974 psi
1 1/2" - 5.195 psi 8" - 4.529 psi
2" - 4.686 psi 10" - 4.390 psi
3" - 4.820 psi 12" - 4.496 psi
4" - 4.622 psi 20" - 4.492 psi
14 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PCW-Produced water; IW-Fresh and de-aerated Water Injection 0ºC / 90ºC ______ 2500 H11
(Note 11)
Pipes and Fittings (Organic coating - according appendix 18) Valves (Organic coating - according appendix 18) (Note 10)
Size Wall or
Item Ends Material Ball (Note 4)
(in) Class
1" XXS 0,250" Size Description Tag
1 1/2" XXS 0,281" API 5L Gr B PSL 1 Ball valve; class 2500; FLG; RTJ; carbon
T-02A 1" - 1 1/2" VE-192
seamless steel, PEEK seat; organic coating.
2" XXS 0,281"
3" XXS 0,438" Ball valve; class 2500; FLG; RTJ; carbon
2" - 3" VE-194
4" XXS 0,674" steel, PEEK seat; organic coating.
Pipe 6" 0,719" Ball valve; class 2500; FLG; RTJ; gear;
BW API 5L Gr X 70 PSL 1 4" - 12" VE-196
(Note 11) T-32 8" 0,906" carbon steel, PEEK seat; organic coating.
Seamless
Ball valve; class 2500; Compact flange; MSJ;
10' 1,125"
14" - 16" gear; carbon steel, PEEK seat; organic VE- 483
12" 1,312" coating.
14" 1,250"
API 5L Gr X 70 PSL 1
T-39
16" SCH 160 1,250" Welded (E=0,85)
L.R.ELL 45º CRL-02 Gate valve; class 2500; FLG; RTJ; gear;
6" - 12" VG-77
Tee TE-02 carbon steel, organic coating.
ASTM A 234 Gr WPB
Red. Tee TRE-01 2" - 6" Gate valve; class 2500; Compact flange;
14" - 16" VG-117
Conc. Red. REDC-01 Wall thickness MSJ; gear; carbon steel, organic coating.
according to BW
Ecc. Red. REDE-01 pipe Globe
Cap TAM-02 Globe valve; class 2500; FLG; RTJ; carbon
2" - 3" VGL-43
Cross CRUZ-02 steel.
Weldolet WOL-01 2" - 16" ASTM A 105 Globe valve; class 2500; FLG; RTJ; gear;
4" - 8" VGL-43E
S.R.ELL 90º CRC-21 caarbon steel.
Ecc. Red. REDE-13 Check valve; dual plate; wafer; class 2500;
2" - 16" VR-112
Cap TAM-30 RTJ; carbon steel; organic coating.
Cross CRUZ-47
FLG-20 WN (RTJ)
1" - 4" ASTM A 105
Flange FLG-21 BLIND (RTJ)
(Note 7) FLG-112 WN (RTJ) Other
6" - 12" 2500
FLG-113 BLIND (RTJ)
ASTM A 694 Gr F 70
Compact FLG-198 WN (MSJ) (Note 8)
Globe valve; needle disc; 5000 psi; threaded
Flange 14" - 16" 1" - 1 1/2" VAG-33
FLG-199 BLIND (MSJ) male/female; carbon steel, organic coating.
(Notes 12 and 13)
Carbon steel coated Zn-Ni
Gasket JA-02 Octagonal
1" - 12" max. hardness 90 Brinell
(Note 2) 2500
JI-05 Oval Fenolic resin
IX Seal ring
JVM-02 14" - 16" _ Carbon steel coated Zn-Ni
(Note 13)
Stud PAE-01 ASTM A 193 Gr B7
3/4" - 1"
Nut (Note 2) ASTM A 194 Gr 2H
Stud PAE-02 1 1/8" - 2 ASTM A 193 Gr B7
Nut (Note 2) 3/4" ASTM A 194 Gr 2H
Stud PAE-09
3/4" - 1"
ASTM A 193 Gr B16
Nut (Notes 2 and 4) ASTM A 194 Gr 7
Stud PAE-10 1 1/8" - 2 ASTM A 193 Gr B16
Nut (Notes 2 and 4) 3/4" ASTM A 194 Gr 7
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PCW-Produced water; IW-Fresh and de-aerated Water Injection 0ºC /90ºC ______ 2500 H11
(Note 11)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 6170
50 6050
70 5830
90 5600
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and
4
ASTM A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
8 Isolating joint see drawing on the appendix 15.
9 When required Fully Tight valve (VET), see types in appendix 14.
10 Maximum working pressure (0ºC/90ºC).
6" - 5.611 PSI 14" - 4550 PSI
8" - 5.417 PSI 16" - 4356 PSI
10" - 5.395 PSI
12" - 5.298 PSI
11 Impact test requirements according API 5L standard.
12 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
13 Compact flange in accordance with NORSOK L-005
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 IW-Fresh and de-aerated Sea Water Injection 0ºC / 70ºC ______ 2500 H14
(Note 4)
Pipes and Fittings (Coated with polyethylene, according to appendix 13) Valves (Note 5)
Size Wall or
Item Tag Ends Material Ball
(in) Class
1" SCH 160 0,250" API 5L Gr B PSL 1 Size Description Tag
T-02A
1 1/2" SCH 160 0,281" seamless
1" - 1 1/2" Ball valve; class 2500; FLG; carbon steel. VE-450
2" 0,250"
3" SCH 160 0,438" Ball valve; class 2500; FLG; RTJ; carbon
2" - 3" VE-16
4" SCH 160 0,531" steel.
1" - 4"
S. R. ELL 90º CRC-26 Gate valve; class 2500; FLG; RTJ; carbon
2" - 4" VG-16
L. R. ELL 90º CRL-39 steel.
Wall thickness
L. R. ELL 45º CRL-38 according to BW Gate valve; class 2500; FLG; RTJ; gear;
pipe ASTM A 694 Gr F 65 6" - 12" VG-17
Tee TE-42 carbon steel.
(Note 6)
Red. Tee TRE-36
2" - 20"
Conc. Red. REDC-14
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 IW-Fresh and de-aerated Sea Water Injection 0ºC / 70ºC _____ 2500 H14
(Note 4)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 70 4323
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
4 Maximum working pressure (0ºC/70ºC).
1 1/2" - 5.591 psi 10" - 4.923 psi
2" - 4.954 psi 12" - 4.834 psi
3" - 5.976 psi 14" - 4.709 psi
4" - 5.605 psi 16" - 4.717 psi
6" - 5.119 psi 20" - 4.657 psi
8" - 4.942 psi
5 When required Fully Tight valve (VET), see types in appendix 14.
6 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
7 Compact flange in accordance with NORSOK L-005.
8 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 15) -20ºC / 100ºC ___ 2500 H30
(Note 9)
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 8) Valves (Note 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1" SCH 160 0,250" Inconel® 625 ASTM B444 (UNS Size Description Tag
T-43
1 1/2" SCH 160 0,281" N06625)
Ball valve; fire tested; class 2500; BW;
1" - 1 1/2" VE-485
2" SCH 80 XS 0,281" RTJ; Inconel® 625; PEEK®/metal seat.
3" SCH 160 0,438" Ball valve; fire tested; class 2500; FLG;
2" - 3" RTJ; carbon steel + Inconel® 625; VE-451
4" SCH 120 0,438" PEEK®/metal seat.
6" 0,625" API 5L Gr X65 PSL 2 Ball valve; fire tested; class 2500; FLG;
T-46 seamless 4" - 12" RTJ; gear; carbon steel + Inconel® 625; VE-452
Pipe 8" SCH 140 0,812" (Note 11) PEEK®/metal seat.
BW
(Note 9) 10" SCH 140 XXS 1" Ball valve; fire tested; class 2500;
14" - 24" compact flanged; MSJ; gear; carbon VE-467
12" 1,250" steel + Inconel® 625; PEEK®/metal
14" SCH 160 1,406"
Wall
S.R. ELL 90º CRC-26 thickness
BW
according to
L. R. ELL. 90º CRL-39
pipe
L. R. ELL. 45º CRL-38
Tee TE-42
ASTM A 694 Gr F 65 (Note
Red. Tee TRE-36
2" - 24" 11)
Conc. Red. REDC-14
Cap TAM-43
Cross CRUZ-27
Butterfly
Globe
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 15) -20ºC / 100ºC ___ 2500 H30
(Note 9)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 6171
50 6058
100 5632
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel® 625 coated according Appendix 16.
9 Maximum working pressure (-20ºC/100ºC).
1 1/2" - 7.710 psi 10" - 4.475 psi
2" - 5.802 psi 12" - 4.734 psi
3" - 6.169 psi 14" - 4.858 psi
4" - 4.698 psi 16" - 4.576 psi
6" - 4.543 psi 18" - 4.542 psi
8" - 4.533 psi 20" - 4.518 psi
24" - 4.479 psi
10 Compact flange in accordance with NORSOK L-005.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Use this Spec only up to SDV.
13 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
14 Impact test requirements according API 5L standard.
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
15
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 B
SHEET:
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 8) Valves (Note 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1" SCH 80S 0,179" Inconel® 625 ASTM B444 Size Description Tag
T-43
1 1/2" SCH 80 0,200" (UNS N06625)
Ball valve; fire tested; class 2500; FLG;
1" - 1 1/2" VE-485
2" SCH 80S 0,218" RTJ; Inconel® 625; PEEK®/metal seat.
3" SCH 80S 0,300" Ball valve; fire tested; class 2500; FLG;
4" - 12" RTJ; gear; carbon steel + Inconel® 625; VE-452P
4" - PIGGABLE 0,312" PEEK®/metal seat.
6" - PIGGABLE 0,500" API 5L Gr X65 PSL 2 Ball valve; fire tested; class 2500; FLG;
Pipe T-46 seamless 14" - 20" MSJ; gear; carbon steel + Inconel® 625; VE-467P
8" - PIGGABLE SCH 120 0,594" BW (Note 11) PEEK®/metal seat.
(Note 9)
10" - PIGGABLE 0,812"
1" - 3"
Cap TAM-52
Short Nip.
(Notes 1 and 6)
Butterfly
Globe
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 4388
50 4388
70 4388
100 4388
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel® 625 coated according Appendix 16.
9 Maximum working pressure (0ºC/100ºC).
1" - 6.942 psi 6" - 4.906 psi 16" - 4.570 psi
1 1/2" - 5.368 psi 8" - 4.477 psi 18" - 4.514 psi
2" - 5.071 psi 10" - 4.910 psi 20" - 4.469 psi
3" - 4.736 psi 12" - 4.461 psi
4" - 4.507 psi 14" - 4.643 psi
10 Compact flange in accordance with NORSOK L-005.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Use this Spec only up to Pig Receivers.
13 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
14 For 3d and 5d bends the maximum wall thickness thinning shall be 15% and 10%, respectively. This bend´s shall be piggable.
15 Impact test requirements according API 5L standard.
16 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 15) -20ºC / 130ºC ___ 2500 H38
(Note 9)
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 8) Valves (Note 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1" XS 80 0,179" Inconel® 625 ASTM B444 (UNS Size Description Tag
T-43
1 1/2" XS 80 0,200" N06625)
Ball valve; fire tested; class 2500; BW;
1" - 1 1/2" VE-485
2" 0,250" RTJ; Inconel® 625; PEEK®/metal seat.
3" SCH 160 0,438" Ball valve; fire tested; class 2500; FLG;
2" - 3" RTJ; carbon steel + Inconel® 625; VE-451
4" SCH 120 0,438" PEEK®/metal seat.
6" 0,625" API 5L Gr X80 PSL 2 Ball valve; fire tested; class 2500; FLG;
T-55 seamless 4" - 12" RTJ; gear; carbon steel + Inconel® 625; VE-452
Pipe 8" SCH 140 0,812" (Note 11) PEEK®/metal seat.
BW
(Note 9) 10" XXS 140 1,000" Ball valve; fire tested; class 2500;
14" - 24" compact flanged; MSJ; gear; carbon VE-467
12" 1,250" steel + Inconel® 625; PEEK®/metal
14" SCH 160 1,406"
Wall
S.R. ELL 90º CRC-29 thickness
BW
according to
L. R. ELL. 90º CRL-44
pipe
L. R. ELL. 45º CRL-45
Tee TE-54
ASTM A 694 Gr F 80 (Note
Red. Tee TRE-48
2" - 24" 11)
Conc. Red. REDC-20
Cap TAM-56
Cross CRUZ-50
Butterfly
Globe
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 PC-Process (Corrosive Hydrocarbon) (Note 15) -20ºC / 130ºC ___ 2500 H38
(Note 9)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 6171
50 6058
100 5632
130 5521
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Grade B16 stud bolts and ASTM
A 194 Grade 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel® 625 coated according Appendix 16.
9 Maximum working pressure (-20ºC/100ºC).
1 1/2" - 7.710"" psi 10" - 5.224" psi
2" - 5.966" psi 12" - 5.526" psi
3" - 7.201" psi 14" - 5.671" psi
4" - 5.484" psi 16" - 5.341" psi
6" - 5.303" psi 18" - 5.302" psi
8" - 5.291" psi 20" - 5.274" psi
24" - 5.229" psi
10 Compact flange in accordance with NORSOK L-005.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Use this Spec only up to SDV.
13 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
14 Impact test requirements according API 5L standard.
15 Materials for use in H2S-containing environments shall be used in strict accordance with the requirements of the ISO 15156 (NACE MR0175).
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
TECHNICAL SPECIFICATION DR-ENGP-1.1 0
SHEET:
Pipes and Fittings (Coated with Inconel® 625 - According appendix 16) (Note 8) Valves (Note 13)
Size
Item Tag Wall or Class Ends Material Ball (Note 4)
(in)
1" SCH 80 XS 0,179" Inconel® 625 ASTM B444 Gr1 Size Description Tag
T-43
1 1/2" SCH 80 XS 0,200" (UNS N06625)
Ball valve; fire tested; class 2500; FLG;
1" - 1 1/2" VE-485
2" SCH 80 XS 0,218" RTJ; Inconel® 625; PEEK®/metal seat.
3" SCH 80 XS 0,300" Ball valve; fire tested; class 2500; FLG;
4" - 12" RTJ; gear; carbon steel + Inconel® 625; VE-452P
4" - PIGGABLE 0,312" PEEK®/metal seat.
6" - PIGGABLE SCH 80 XS 0,432" API 5L Gr X80 PSL 2 Ball valve; fire tested; class 2500; FLG;
Pipe T-55 seamless 14" - 20" MSJ; gear; carbon steel + Inconel® 625; VE-467P
8" - PIGGABLE 0,562" BW (Note 11) PEEK®/metal seat.
(Note 9)
10" - PIGGABLE SCH 100 0,719"
1" - 3"
Cap TAM-52
Short Nip.
(Notes 1 and 6)
Butterfly
Globe
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 6171
50 6058
100 5632
130 5521
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 For SDVs and it's by pass (if existing) or when design especified, "fire tested" ball valves shall be used. ASTM A 193 Gr B16 stud bolts and ASTM A
194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
5 For H2S and CO2 services. Where corrosion risk exists, see appendix 5.
6 Use niple THD X PLAIN and threaded cap after drains and vents blocking.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 All piping shall be internal Inconel® 625 coated according Appendix 16.
9 Maximum working pressure (0ºC/130ºC).
1" - 6.942 psi 6" - 5.217 psi 16" - 5.310 psi
1 1/2" - 5.368 psi 8" - 5.213 psi 18" - 5.280 psi
2" - 6.242 psi 10" - 5.351 psi 20" - 5.248 psi
3" - 5.829 psi 12" - 5.296 psi
4" - 5.547 psi 14" - 5.360 psi
10 Compact flange in accordance with NORSOK L-005.
11 Maximum carbon equivalent CE iiw = 0,43% or CE pcm = 0,25%.
12 Use this Spec only up to Pig Receivers.
13 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
14 For 3d and 5d bends the maximum wall thickness thinning shall be 15% and 10%, respectively. This bend´s shall be piggable.
15 Impact test requirements according API 5L standard.
16 Materials for use in H2S-containing environments shall be used in strict accordance with the requirements of the ISO 15155
(NACE MR0175).
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
TECHNICAL SPECIFICATION DR-ENGP-1.1 0
CLIENT: SHEET:
ASME B31.3 FP-Production and Drilling Fluid; CE-Cement 0ºC / 38ºC (3,2 mm) 10000 psi J5
Pipes and Fittings Valves
Size Wall or
Item Tag Ends Material Ball (Note 4)
(in) Class
1" - 1 1/2" Size Description Tag
Pipe XXS
2" - 6"
API 5L Gr X70 PSL 1
T-32 BW
Short Nip. seamless
1" - 1 1/2" XXS
Long Niple
Tee TE-22
Cap TAM-30
Cross CRUZ-47
Weldolet WOL-09
Gate
Globe
Check
Check valve; dual plate; wafer; max.
2" - 6" VR-142
pressure 10000 psi; carbon steel; viton seat.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 FP-Production and Drilling Fluid; CE-Cement 0ºC / 38ºC (3,2 mm) 10000 psi J5
Pressure / Temperature Rating
(to DN 1/2" up to 1 1/2")
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
up to 38 10000
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 The transition between the ASME flanges and NORSOK L-005 flanges will be defined during the detail.
5 For 3d and 5d bends the maximum wall thickness thinning shall be 15% and 10%, respectively. This bend´s shall be piggable.
6 Impact test requirements according API 5L standard.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Cap TAM-32
Union UN-20
Tee TE-25
Cross CRUZ-21
ASTM A 182 Gr F55
Weldolet WOL-05 2" - 6"
(UNS S32760)
Check
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
Up to 38 7200
65 7200
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded cap (TAM-) after drains and vents blocking.
3 Flanges ≤ 1 1/2" may be used, if strictly necessary.
4 Use only when recommended by Appendix 5.
5 See Appendix 16 - Welding qualification requirements for super duplex.
6 See Appendix 17 - Minimum requirements for valves casted in super duplex.
7 Max. pressure (0ºC/65ºC) - 7200 PSIG.
8 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
9 For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM
A 194 Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
10 Isolating joint see drawing on the appendix 15.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 P-Process (Note 14); DOH-Carbon Dioxide w/ Hydrocarbon -100ºC / 123ºC (1,6 mm) 10000 J31
(Note 12)
4" 0,688"
Pipe ASTM A 333 Gr 8
(Notes 8, 11 and T-40 6" 1,000" BW seamless
14) (Note 8 and 15 )
8" 1,250"
10" 1,562"
12" 1,812"
14" 2,000"
16" 2,344"
Wall thickness
BW
L. R. ELL 90º CRL-32 according to pipe
Check
Check valve; API 10000; compact
2" - 8" flange NORSOK L-005; MSG; Alloy VR-143
steel.
IX Seal ring
JVM-03 1" - 16" API 10000 Inconel® 625
(Note 5)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 P-Process (Note 14); DOH-Carbon Dioxide w/ Hydrocarbon -100ºC / 123ºC (1,6 mm) 10000 J31
(Note 12)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
- 8776 - -
- - - -
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded plug after drains and vents blocking.
3 Flanges ≤ 1 1/2" may be used, if strictly necessary.
4 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
5 Compact flange in accordance with NORSOK L-005.
6 Bolts and nuts in accordance with NORSOK M-001.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 Charpy impact test is required for low temperature services materials in accordance ASTM A 333.
9 Charpy impact test is required for low temperature services materials in accordance ASTM A 420.
10 Charpy impact test is required for low temperature services materials in accordance ASTM A 522.
11 High pressure piping according to Chapter IX and appendix K of ASME B31.3.
12 For pressure exceed standard L-005, design according manufacturer.
13 Pressure / Temperature Rating shall be informed by the vendor and approved by PETROBRAS.
All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
14
MR0175)
15 According appendix 16.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.4/ASME B31.8 P-Process (Note 15); DOH-Carbon Dioxide w/ Hydrocarbon -100ºC / 123ºC (1,6 mm) 10000 J31P
Pipes and Fittings Valves (Note 7)
Size Wall or
Item Tag Ends Material Ball
(in) Class
1" XXS 0,358" Size Description Tag
6" 0,906"
8" 1,188"
Globe
Check
IX Seal ring
JVM-03 1" - 8" API 10000 Inconel® 625
(Note 5)
ASME B31.4/ASME B31.8 P-Process (Note 15); DOH-Carbon Dioxide w/ Hydrocarbon -100ºC / 123ºC (1,6 mm) 10000 J31P
Pressure / Temperature Rating
(Note 12)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
- 8776 - -
- - - -
- - - -
- - - -
- - - -
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded plug after drains and vents blocking.
3 Flanges ≤ 1 1/2" may be used, if strictly necessary.
4 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
5 Compact flange in accordance with NORSOK L-005.
6 Bolts and nuts in accordance with NORSOK M-001.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 Charpy impact test is required for low temperature services materials in accordance ASTM A 333.
9 Charpy impact test is required for low temperature services materials in accordance ASTM A 420.
10 Charpy impact test is required for low temperature services materials in accordance ASTM A 522.
11 For pressure exceed standard L-005, design according manufacturer.
12 Pressure / Temperature Rating shall be informed by the vendor and approved by PETROBRAS.
13 For 3d and 5d bends the maximum wall thickness thinning shall be 15% and 10%, respectively. This bend´s shall be piggable.
14 All valves and pipes specified for hydrogen sulfide service (NACE) shall be in strict accordance with the requirements of the ISO 15156 (NACE
MR0175)
15 According appendix 16.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 P-Process (Note 13) -82ºC / 155ºC (1,6 mm) 10000 J40
(Note 11)
14" 1,438"
(Notes
N00625)
1, 2 and 11)
Long Nip.
Weldolet WOL-14
Check
Check valve; API 10000; compact
2" - 8" flange NORSOK L-005; MSG; Alloy VR-163
steel.
IX Seal ring
JVM-03 1" - 16" API 10000 Inconel® 625
(Note 5)
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
N: REV:
ASME B31.3 P-Process (Note 14); DOH-Carbon Dioxide w/ Hydrocarbon -82ºC / 155ºC (1,6 mm) 10000 J40
(Note 11)
Temp. (ºC) Max. Press. (psig) Temp. (ºC) Max. Press. (psig)
- 8759 - -
- - - -
Branch Connections
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Use niple THD X PLAIN and threaded plug after drains and vents blocking.
3 Flanges ≤ 1 1/2" may be used, if strictly necessary.
4 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
5 Compact flange in accordance with NORSOK L-005.
6 Bolts and nuts in accordance with NORSOK M-001.
7 When required Fully Tight Valve (VET), see types in appendix 14.
8 Charpy impact test is required for low temperature services materials in accordance ASTM B 444.
9 Charpy impact test is required for low temperature services materials in accordance ASTM B 564.
10 High pressure piping according to Chapter IX and appendix K of ASME B31.3.
11 For pressure exceed standard L-005, design according manufacturer.
12 Pressure / Temperature Rating shall be informed by the vendor and approved by PETROBRAS.
13 Materials for use in H2S-containing environments shall be used in strict accordance with the requirements of the ISO 15156
(NACE MR 0175).
15 According appendix 16.
THE DATA OR PARTS THEREOF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 1 of 5
APPENDIX 1
Connection Details for Temperature Wells
Type of Installation
Curved Vertical/Horizontal
SPEC Pipe Diameter
Diam. 3/4" Diam. 1½” Diam. ¾” Diam. 1½” Flg
threaded Flg threaded
¾” - 1 ½” Type 1A
A4 2” Type 1B
A8 3” - 4” Type 1C
B30 ¾” - 2” Type 1D
3” - 4” Type 1E
B3 B4
B5 B6
¾” - 1 ½” Type 2A
B7 B7R
B9 B10
B11 B12
B13 B14
B15 B16
B17 B19
C3 C4
2” Type 2B
C5 C6
C8 C9
C10 C12
C11 C13
C16 C30
E3 E4
E5 E6
E6R E8
E9 E10
3” and greater Type 2C
E10R
E11 E16
E17 E30
E14 E32
F3 F4 ¾” - 2”
F5 F6
F6R F10 Type 2D
F10R F11
F14 F16
APPENDIX 1
Connection Details for Temperature Wells
F32 G3
G4 G5
G6 G6R
G10 G10P
G10R G11
G12 G12P
G14 G16
G16P G18
G19 H3
H5 H6 H10 3” and greater Type 2E
H11 H10P
H14 H30
H30P H38
H38P J5
J12 J31
J31P J40
B20
B21
B22
B23
B24
B25
APPENDIX 1
Connection Details for Temperature Wells
THREADED THERMOWELLS
APPENDIX 1
Connection Details for Temperature Wells
FLANGED THERMOWELLS
APPENDIX 1
Connection Details for Temperature Wells
APPENDIX 2
Connection Details for Drains and Vents
1 – Drains:
¾” VI ¾”
1” - 1 ½” V (*) ¾”
B7 B7R
2” - 4” II ¾” VG-36
6” - 10” II 1”
12” - 36” II 1 ½”
1 – Drains: (continued)
Spec Pipe Diameter Drain Type Drain Diameter Valves
VE-48B/ VE-48D
¾” - 1 ½” III ¾”
VE-305B/VE-305D
2” - 4” IV ¾”
B9 VE-333B/VE-337B
6” - 10” IV 1”
VE-333D
12” - 36” IV 1 ½”
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
E11 VE-202
6” - 10” IV 1”
12” - 24” IV 1 ½”
¾” - 1 ½” IX ¾”
2” - 4” X ¾”
C11 VE-201/ VE-205
6” - 10” X 1”
12” - 16” X 1 ½”
VE-381B/ VE-381C
VE-382B/ VE-382C
¾” - 1 ½” III ¾” VE-393B/ VE-393C
E10 2” - 4” IV ¾” VE-397B/ VE-397C
6” - 10” IV 1” VE-401B/ VE-401C
12” - 24” IV 1 ½” VE-405B/ VE-405C
E10R VE-04B
B12 C12 VE-354/ VE-364
1 – Drains: (continued)
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
B17 VE- 333D/ VE-337D
6” - 10” IV 1”
12” – 36” IV 1 ½”
¾” - 1 ½” III ¾”
VE-330C/ VE-330B
2” - 4” IV ¾”
B19 VE-296C/ VE-299C
6” - 10” IV 1”
VE-302C/ VE-302B
12” – 36” IV 1 ½”
B20 VE-159
B21 VE-160
B25 VE-158
¾”
B7 B7R B22 12” – 16” IV 1” VG-36
B23 B24 1 ½”
¾” - 1 ½” III ¾”
B30 VE-463
¾” - 1 ½” I ¾”
C8 E8 2” - 4” II ¾” VE-01
6” - 8” II 1”
¾” - 1 ½” ¾”
III
2” - 4” ¾”
C16 IV VE-209/ VE-212
6” - 10” 1”
IV
12” - 24” 1 ½”
IV
¾” - 1 ½” III ¾”
2” - 4” IV ¾” VE-221/ VE-224
E16
6” - 10” IV 1” VE-233/ VE-293
12” – 16” IV 1 ½”
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
E17 VE-333D/ VE-337D
6” - 10” IV 1”
12” - 24” IV 1 ½”
¾” - 1 ½” III ¾” ¾”
2” - 4” IV ¾” ¾”
C30
6” - 10” IV 1” 1”
12” - 24” IV 1 ½” 1 ½”
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
E30 E32 VE-459
6” - 10” IV 1”
12” - 16” IV 1 ½”
III ¾” VE-237/ VE-237B
¾” - 1 ½”
IV ¾” VE-270/ VE-270B
F3 2” - 4”
IV 1” VE-275/ VE-275B
6” - 10”
VE-280/ VE-280B
¾” - 1 ½” III ¾”
2” - 4” IV ¾” VE-238B/ VE-238C
G3
6” - 10” IV 1” VE-285B/ VE-285C
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
F4 G4 VG-46
6” - 10” IV 1”
12” - 18” IV 1 ½”
F5 2” - 6” VII 2 1/16” VG ABRAS-05
¾” - 1 ½” III ¾”
2” - 4” IV ¾”
F16 VE-227/ VE-440
6” - 10” IV 1”
12” – 16” IV 1 ½”
¾” - 1 ½” VE-94B/VE-94C
F6 F6R 2” - 4” III ¾”
6” - 16” IV ¾”
IV 1” VE-94D
G6 G6R
1 – Drains: (continued)
¾” - 1 ½” ¾”
III
2” - 4” ¾”
G12 IV VE-168/ VE-171
6” - 10” 1”
IV
12” - 24” 1 ½”
IV
¾” - 1 ½”
2” - 4”
¾”
6” - 10” III
¾”
G12P 12” - 14” IV VE-171
1”
IV
1 ½”
IV
1” - 1 ½” III ¾” VE-47
2” - 4” IV ¾”
G14
6” - 10” IV 1”
12” - 18” IV 1 ½”
¾” - 1 ½” III ¾” VE-227/ VE-440
2” - 4” IV ¾”
G16
6” - 10” IV 1”
12” - 24” IV 1 ½”
VII 1”
2” - 10” VII 1 ½”
F14 G14 VE-47
12” - 18”
1” - 1 ½”
J12 2” - 3” VG-87
4” - 6”
1” - 1 ½”
2” - 4”
J31 VET 1452
6” - 10”
12” - 14” IV 1”
1” - 1 ½”
2” - 4”
J31P VET 1452
6” - 8”
1” - 1 ½”
2” - 4”
J40 VET 1602
6” - 14”
(*) Type V – For piping ND 1”, instead of reduction coupling, use reduction tee 1” x ¾”.
1 – Drains
2 – Vents:
Spec Pipe Diameter Vent Type Vent Diameter Valves
¾” - 1 ½” I
A4 VG-36
≥2” II
III
¾” - 1 ½”
A8 IV VE-44
≥2”
III VE-230/ VE-231 VE-240
B3 ¾” - 1 ½”
IV VE-243 VE-246/ VE-249
≥2”
¾” VE-255
III
¾” - 1 ½”
C3 IV VE-230/VE-246
≥2”
III
¾” - 1 ½” VE-230/ VE-261 VE-
E3 IV
≥2” 264/VE-267
III
¾” - 1 ½”
B4 C4 E4 IV VG-45
≥2”
B5 C5 E5 2” - 6” VII 2 1/16” VG ABRAS-04
III
¾” - 1 ½” VE-296B/VE-299B
B6 IV
≥2” VE-302B/VE-330B
III
¾” - 1 ½”
C6 E6 E6R IV VE-91B/ VE-91C
≥2”
I
B7 B7R ¾” - 1 ½”
II VG-36
≥2” ¾”
VE-48B/ VE-48D
III VE-305B/VE-305D
¾” - 1 ½”
B9 IV VE-333B/VE-337B
≥2”
VE-333D
VE-48B/ VE-48D
III
¾” - 1 ½” VE-309B/ VE-309D
C9 IV
≥2” VE-337D
III
E9 ¾” - 1 ½”
IV ¾” VE-373D/ VE-377D
≥2”
2 – Vents: (continued)
Spec Pipe Diameter Vent Type Vent Diameter Valves
VE-048B/VE-48C
III VE-305B/ VE-309B
¾” - 1 ½”
IV VE-313C/ VE-317C
≥2”
VE-333B/ VE-337B
B10 VE-341C/ VE-342C
¾” - 1 ½” III
B11 ≥2” IV VE-346B/ VE-350B
VE-305B/ VE-309B
III
¾” - 1 ½” VE-317C/ VE-321C
IV
≥2” VE-325C/ VE-333B
C10 VE-337B/ VE-341C
III
¾” - 1 ½”
C11 IV VE-201/ VE-205
≥2”
VE-381B/ VE-381C
VE-382B/ VE-382C
VE-393B/ VE-393C
E10 VE-397B/ VE-397C
¾” - 1 ½” III VE-401B/ VE-401C
≥2” IV VE-405B/ VE-405C
E10R VE-04B
B12 C12 VE-354/ VE-364
E11 VE-202
B13 C13 VE-74
B14 VE-44
1” - 1 ½” VII
C14 VE-45
≥2” VI
E14 VE-46
¾” - 1 ½” III
B15 VE-04C
≥2” IV
¾” - 1 ½” III
B17 VE-333D/ VE-337D
≥2” IV
2-Vents: (continued)
Spec Pipe Diameter VentType Vent Diameter Valves
VE-330C/ VE-330B
¾” - 1 ½” III
B19 VE-296C/ VE-299C
≥2” IV
VE-302C/ VE-302B
B20 ¾” VE-159
B21 VE-160
B25 VE-158
III
¾” - 1 ½” VG-36
B22 B23 B24 IV
≥2”
III
¾” - 1 ½”
B30 IV
≥2”
¾” - 1 ½” I
C8 E8 ≥2” II VE-01
¾” - 1 ½” III
C16 VE-209/ VE-212
≥2” IV
¾” - 1 ½” III
E17 ≥2” IV VE-333D/ VE-337D
III
¾” - 1 ½”
C30 IV VE-463
≥2”
¾” - 1 ½” III
E30 E32 VE-459
≥2” IV
VE-237/ VE-237B
¾” - 1 ½” III VE-270/ VE-270B
F3
≥2” IV VE-275/ VE-275B
VE-280/ VE-280B
2 – Vents: (continued)
Spec Pipe Diameter VentType Vent Diameter Valves
¾” - 1 ½” III
F4 G4 ≥2” IV VG-46
F5 2” - 6” VI VG ABRAS-05
III
F10R ¾” - 1 ½” VE-05B/ VE-05C
IV
≥2” VE-102B / VE-102C
F11 VE-186D
¾” - 1 ½” III
F32 VE-487
≥2” IV
G11 ¾” - 1 ½” III VE-186D/VE-189D
G12 ≥2” IV VE-168/VE-171
G12P VE-171
¾” - 1 ½” III
G16 VE-227/ VE-440
≥2” IV
¾” - 1 ½” III
G16P VE- 440
≥2” IV
¾” - 1 ½” III
G18 VE-43D
≥2” IV
¾” - 1 ½” III
G19 VE-94D/VE-412
≥2” IV
1” - 1 ½” VI VE-463C/ VE-463D
H3 ≥2” 1” VE-466 C/ VE-466D
H5 2” - 6” VI 2 1/16” VG ABRAS-07
H10 VE-458/VE-459
1” - 1 ½” VI
H10P 1” VE-161D
2” - 8” VI
1” - 1 ½” VI
H11 ≥2” VI VE-192/VE-193
1” - 1 ½” VI
H14 ≥2 VI VE-458
VI ¾”
F14 G14 ≥2” VE-47
G5 2” - 6” VI 2 1/16” VG ABRAS-06
¾” - 1 ½” III
G10 VE-437D / VE-439D
≥2” IV
¾” - 1 ½” III VE-102D/ VE-43D
G10P G10R
≥2” IV VE-102D
1” - 1 ½” VI
H30 H30P VE-450
≥2” VI
1”
1” - 1 ½” VI
H38 H38P VE-485
≥2” VI
1” - 1 ½” VI
J5 VG-ABRAS 08
≥2” VI
2 1/16”
J12 2” - 6” VI VG-87
1” - 1 ½” VI
J31 J31P VET-1452
≥2” VI 1”
1” - 1 ½” VI
J40 VET-1602
≥2” VI 1”
2 - Vents
APPENDIX 3
Connection Details for Pressure Instruments
III
E6 ¾” - 1 ½”
C6 E6 IV VE-91B/ VE-91C
R ≥2”
I
B7 B7R ¾” - 1 ½”
II VG-36
≥2”
VE-48B/ VE-48D
III VE-305B/VE-305D
¾” - 1 ½”
B9 IV VE-333B/VE-337B
≥2”
VE-333D
VE-48B/ VE-48D
III
¾” - 1 ½” VE-309B/ VE-309D
C9 IV
≥2” VE-337D
III
¾” - 1 ½”
E9 IV ¾” VE-373D/ VE-377D
≥2”
VE-305B/ VE-309B
III
¾” - 1 ½” VE-317C/ VE-321C
IV
≥2” VE-325C/ VE-333B
C10 VE-337B/ VE-341C
III
¾” - 1 ½”
C11 IV
≥2”
VE-381B/ VE-381C
VE-382B/ VE-382C
VE-393B/ VE-393C
E10 VE-397B/ VE-397C
¾” - 1 ½” III VE-401B/ VE-401C
≥2” IV VE-405B/ VE-405C
E10R VE-04B
B12 C12 VE-354/ VE-364
E11 VE-202
¾” - 1 ½” III
B13 C13 VE-74
≥2” IV
B14 VE-44
1” - 1 ½” VII
C14 VE-45
≥2” VI
E14 VE-46
¾” - 1 ½” III
B15 VE-04C
≥2” IV
¾” - 1 ½” III
B17 VE-333D/ VE-337D
≥2” IV
¾” - 1 ½” III
B30
≥2” IV
¾” - 1 ½” I
C8 E8 ≥2” II VE-01
¾” - 1 ½” III
C16 VE-209/ VE-212
≥2” IV
¾” - 1 ½” III
E17 VE-333D/ VE-337D
≥2” IV
III
¾” - 1 ½”
C30 IV VE-463
≥2”
III
¾” - 1 ½”
E30 E32 IV VE-459
≥2”
VE-237/ VE-237B
III
¾” - 1 ½” VE-270/ VE-270B
F3 IV
≥2” VE-275/ VE-275B
VE-280/ VE-280B
¾” - 1 ½” III
VE-238B/ VE-238C
G3 ≥2” IV
VE-285B/ VE-285C
F5 2” - 6” VI VG ABRAS-05
III
F10R ¾” - 1 ½” VE-05B/ VE-05C
IV
≥2” VE-102B / VE-102C
III
¾” - 1 ½”
F11 IV VE-186D
≥2”
III
¾” - 1 ½”
F32 IV VE-487
≥2”
G11 ¾” - 1 ½” III VE-186D/VE-189D
G12 ≥2” IV VE-168/VE-171
G12P ¾” VE-171
¾” - 1 ½” III
G16 VE-227/ VE-440
≥2” IV
¾” - 1 ½” III
G16P VE- 440
≥2” IV
¾” - 1 ½” III
G18 VE-43D
≥2” IV
¾” - 1 ½” III
G19 VE-94D/VE-412
≥2” IV
¾” - 1 ½” III
VE-463C/ VE-463D
H3 ≥2” IV
VE-466 C/ VE-466D
H5 2” - 6” VI VG ABRAS-07
¾” - 1 ½” III
H10 2” - 8” IV VE-458/VE-459
¾” - 1 ½” III VE-161D
2” - 8” IV
H10P
¾” - 1 ½” III
H14 ≥2” IV VE-458
VI 1”
F14 G14 ≥2” VE-47
G5 2” - 6” VI VG ABRAS-06
¾” - 1 ½” III
G10 VE-437D / VE-439D
≥2” IV
¾” - 1 ½” III VE-102D/ VE-43D
G10P G10R
≥2” IV VE-102D
III
¾” - 1 ½”
H30 H30P IV VE-450
≥2”
¾” - 1 ½” III ¾”
H38 H38P VE-485
≥2” IV
J5 2” - 6” VI VG ABRAS-08
¾” - 1 ½” III
J12 VG-87
≥2” IV
¾” - 1 ½” III
J31 J31P VAG-42
≥2” IV
¾” - 1 ½” III
J40 VET-1602
≥2” IV
APPENDIX 4
APPENDIX 4
F4 G4 VG-46
F6 F6R VE-94C
G6 G6R G19 VE-94D
VE-05C/VE-
F10 F10R
102C
F11 VE-186D
F32 VE-487
G5 VE-49D
G10 VE-43D/VE-49D
VE-102D
VE-43D/VE-
G10P G10R ¾” 102D
VE-186D/VE-
G11
189D
VE-168 / VE-
G12
171
G12P VE-171
G16 G16P VE-227/ VE-440
G18 VE-43D
H3 VE-60C/VE-63C
VE-161D/VE-
H10 H10P
162D
H5 VE-161D
H11 VE-192/VE-193
J5 VG-ABRAS08
J12 VG-87
APPENDIX 4
Note: For Specs B14; C14; E14; F14; G14 and H14 it´s not recommended orifice flanges use. In
this lines, the flow tapes shall be installed at stainless steel AISI-316 spacers rings.
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
Gaseous Hydrocarbons
- Water (H20)
- Carbon dioxide (CO2)
- Hydrogen Sulfide Gas (H2S)
1.1 - Water
Figure 3 denotes the maximum water content in the gas in terms of total temperature
and pressure to prevent condensation.
The carbon dioxide is only corrosive in the presence of free water, when it is
dissolved, producing carbonic acid. The formation of carbonic acid (H2CO3) reduces
the water’s pH level, making it more corrosive and provides the formation of iron
carbonate film. When this film is not adherent and protective, it generates localized
corrosion, according to the following reactions:
Fe + H2CO3 = FeCO3 + H2
- Pressure
- Temperature
- Composition of the water (dissolved mineral salts)
- Organic Acids (manly acetic and formic acids)
The increase to the solubility of the CO2 in the water is directly proportional to the
increase in pressure and inversely proportional to the increase in temperature.
The mineral salts in the water may prevent reduction of the pH level.
In reservoirs which produce natural gas, condensate and water containing low levels
of mineral salts, pressure is the main factor for controlling the solubility of the CO2.
For this reason, the partial pressure of the CO2 in the gaseous mixture is used to
determine the degree of corrosiveness.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 2 of 11
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
The partial pressure of a given gas in a mixture is the pressure which would be
exerted in the event only the aforesaid gas was present, at the same temperature
and total volume occupied by the mixture.
The partial pressure of each component is equal to the total pressure of the system
multiplied by the molar fraction of the component (% in volume). In the case of the
partial pressure of CO2 (PCO2) the expression is the following:
The hydrogen sulfide gas is soluble in water, forming a weak acid, which causes
corrosion and helps allows atomic hydrogen to penetrate the metals.
The general reaction for this kind of corrosion may be denoted by the formula:
+ 2-
H2S → 2H + S
Fe + 2H+ →Fe2+ + H2
2+ 2-
Fe + S →FeS
_____________________________________________________________
Fe + H2S →FeS + H2
The ferrous sulfate produced under this reaction generally adheres to the surface of
the steel in the form of a black powder or scaling. This FeS scaling acts as a cathode
on the steel, resulting in pitting corrosion.
The most serious problem probably entails the penetration of the atomic hydrogen
produced on the steel, where some of these hydrogen atoms react, forming
hydrogen gas on the interfaces between the inclusions and the metal. Hydrogen gas
accumulating in the defects to the crystalline structure, especially in the region
surrounding the grains or metal/inclusion interfaces, will produce high internal
pressures, which could cause fractures or bubbles in the metal, provoking the stress
corrosion cracking or reducing the fatigue life of the material.
2HAdsorbed → H2
In the same way as the case of CO2, the pressure is a factor of control of the
solubility of H2S in the medium in which this gas is dissolved. For this reason, the
partial pressure of H2S (pH2S) in the gaseous mixture is also used to determine the
corrosiveness level, associated or not to the partial pressure of CO2.
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
The gas is considered corrosive when the partial pressure of H2S in the gas mixture
is higher than 0.05 psia (Ref. 3). This criteria is used to good effect by many gas
distributing companies operating in the USA.
Another parameter for verification of the corrosiveness level with regard to the
Sulfide Stress Cracking (SCC) is the use of the correlations showed in Figures 1 and
2, which consider the partial pressures of H2S and CO2, the pH of the medium and
hardness of the exposed material (Ref.3). For a good estimate of the pH, a software
or a chemical model capable to calculate the pH based on the partial pressures of
the gases and the chemical composition of the water can be used.
For multiphase flow of liquid, gaseous hydrocarbons and water we recommend the
graphs set out on the attached sheet, Figures 1 and 2, which consider the partial
pressures of H2S and CO2, the pH of the medium and hardness of the exposed
material as parameters to check the degree of corrosiveness (Ref.3). For a good
estimate of the pH, a software or a chemical model capable to calculate the pH
based on the partial pressures of the gases and the chemical composition of the
water can be used.
A water cut higher than 30% can impede that the present oil exercises an efficient
action in the prevention of the corrosion favoring the oil/water separation.
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
Maximum
Spec Material Qualified Coatings Observations
Temperature
o Onshore
60 C B25 RPVC -
Installations
B11 C11
65oC E11 F11
G11 H11
Belzona 1321 and 5891
90oC
Belzona 1391
Resinar Flake Glass 500 N
120oC
Nova Coating IPC Magna
CS + Organic Ciapowder 401 Offshore and
Coating Onshore
(Appendix 18) Installations
B11
Belzona 1522
Chesterton ARC 855 HT
Resinar Flake Glass 500 EN
Nova Coating IPC ME35
150oC Sauereisen Fibrecrete 218
Hallar 9414
Hallar 6614 + 6014
DuPont XF
Scothkote 134
Obs: The qualified products for application in higher temperatures can be used in lower
temperatures.
Note:
(3) B9, C9, E9. (API 5L Gr. B), F3, G3. (316L)
(4) B10, C10, E10, F10, G10, G10P. (API 5L Gr. B).
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
(6) B25 (RPVC)
(7) Carbon Steel API 5L grade B + Liner (or Clad) Inconel alloy 625.
(8) CO2 corrosion rate shall be calculated according to program for evaluation and
determination of corrosion of steels NORSOK M-506. The NORSOK software for
corrosion rate is available on site http://www.standard.no/imaker.exe?id=1369)
(9) ACR - Annual Corrosion Rate (mm/year); HAZ – Heat Affected Zone
(10) Requirements for Carbon Steel materials and equipment for services with H2S:
a) Materials and equipment shall fully comply with the requirements of NACE
MR0175, NACE TM 0177 and NACE TM0284;
b) At least three rows of tests shall be accomplished in the case of NACE TM 0177
and NACE TM 0284;
c) For each test condition, set in the standard, at least three samples shall be tested;
d) At least two of the three samples shall be considered approved;
e) In the case of the NACE TM 0177, the test shall be performed for at least thirty
days, with continuous H2S bubbling;
f) Regarding NACE TM 0284, the “A” Solution shall be used. The maximum
acceptable CLR index shall be 1% and the maximum acceptable CTR index shall be
0,5%.
g) Considering NACE TM0177, the “B” Solution shall be chosen. The test shall be
performed using the “A” Method for the base metal and “C” Method for the welded
joint. The applied load shall correspond to 90% of yield limit specified for the base
metal and 85% of the yield limit for the welded joint;
h) The qualification of all welding procedures shall include the tests fixed in items “E”
and “G” of this specification;
i) During the qualification of the welding procedure, the Vickers hardness profile shall
be recorded with a 5Kg load (HV5) over the thermally zone (HAZ) of the welded joint
and the highest value found shall be identified;
j) For the tests according to NACE TM0177, samples with the Maximum Equivalent
Carbon, the highest yield stress and the highest hardness shall be chosen;
k) The welding of specimens shall be performed with the heat input of at least 90%
of the heat input specified in the qualified welding procedure;
l) The welding fillets shall be performed always from the base metal to the welding
metal so that to temper the thermally affected zone (HAZ);
m) The welding HV5 hardness values shall be lower than the highest hardness
obtained in the welding procedure qualification;
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
(14) – Requirements for Duplex (22 Cr) and Super Duplex (25 Cr) materials and
equipment for services with H2S:
a) Maximum hardness for Duplex = 310 HV10 / 28 HRc and Super Duplex = 330
HV10/32 HRc
b) PREN of Duplex > 30 ; PREN of Super Duplex > 40
c) Ferrite content (volumetric fraction) for Duplex and Super Duplex shall be between
35% and 65%
References:
01 - Corrosion Control of Production Equipment for the Offshore Pampo Field - The
British Petroleum Company Limited - JULY 1979.
02 - How el Paso Designs sour Gas Pipe lines - Pipeline Industry - March 1981.
03 - Sulfide Stress Cracking Resistent Metallic Material for Oil Field Equipments -
NACE Standard MR0175/ISO 15156.
04 - Aramco Materials System Specifications - Sour Wet Service Line Pipe 01-
AMSS-16.
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
Figure 1 – Calculation of the pH in function of the H2S and CO2 Partial Pressures,
-
Temperature and bicarbonate (HCO3 ) concentration in the water (Ref. 3).
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
Figure 2 – Diagram of hardness limits for steel type API 5L proposed for sour service in
function of the pH and the H2S partial pressure (Ref. 3).
APPENDIX 5
Corrosive Effect of Liquid Gaseous Hydrocarbons and Produced Water
Figure 3: Effect of pressure and water content on the gas dew point.
APPENDIX 10
Procedure for Coating Backing flanges, Bolts and Nuts
1 - This appendix specifies the procedures to coat backing flanges, screws and nuts
with Zinc/Nickel by electrodeposition.
1.1.1 - Class 1 – The deposits should have a minimum 8% and maximum 12% nickel
content;
1.1.3 - Type E – Plus organic Topcoat degree ASTM 8, µm (minimum Zn-Ni coating
thickness micrometer) and 15, µm (maximum Zn-Ni coating thickness micrometer).
1.4 - Final Inspection – The layer should be inspected with a micrometer, deltascope
or radiograph.
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
Index
1 - Objective
2 - Service Scope
3 - Project Conditions
4 - Anode Specification
6 - Reference Electrode
7 - Storage
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
1. Objective
Any omissions in this this specification can be resolved by contacting the anode
manufacturers, providing approval has been granted by the Petrobras
Inspection.
2. Service Scope
The anodes should be installed according to the instructions set out in this is
specification.
Due to the fact the anode mass is sized empirically, the system's performance
should be evaluated by the assembler and/or manufacturer of the anodes
following their assembly, at the criteria of the PETROBRAS Inspection.
3. Project Conditions
The anode mass has been calculated using the applicable calculation criteria,
and the anode data is in accordance with the PETROBRAS specification, see
item 4.
The anodes should be located in the internal part of all the straight pipe sections.
These anodes will be selected for all the flanged connections.
The short sections or sections which obstruct free passage, will not contain
anodes.
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
Care should be taken during the installation not to hinder the operation of the
valves and other piping elements.
4. Anode Specifications
Continuous sacrificial anodes will be used, which should comply with the following
recommended by PETROBRAS.
- Aluminum alloy anodes – ACS Type – 0.4m
- The anodes will be 25mm in diameter, applicable to 6" to 24" piping respectively.
The installation and fixing of anodes on the SPOOLS shall be carried out as the
diagram below:
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
6. Reference Electrode
7. Storage
The sacrificial anodes should be stored so as to avoid damage, and also to avoid
contamination by chemical products, oil, grease etc.
Other storage precautions for the cathodes should be taken together with the
suppliers, in accordance with PETROBRAS standard N-1729.
During installation in the piping, the anodes and reference electrodes should be
completely free of grease, oil or other product which reduces the efficiency
thereof.
APPENDIX 11
Specifications for Utilization Sacrificial Anodes in Piping
Welding the anodes and reference electrodes in the piping should be performed
with the same level of quality applicable to the piping it self.
The anodes and reference electrodes should only be welded to the piping when
they are ready to be adopted.
Following the welding of the anodes and reference electrodes, the parts of the
epoxy paint which have been affected by the heat should be re-painted.
Care should be taken not to cover any part of the anode surfaces with paint
splashes or any other dielectric element, which will reduce the efficiency thereof.
APPENDIX 12
Branch Connections Tables
Specification Type
A4 - A8
B3 - B4 - B5 - B6 - B9 - B10 - B11 - B12- B13 - B14-
B16- B17- B19
C3 - C4 - C5 - C6 - C9 - C10- C11 - C12 - C13 - C14 -
C16 – C30
E3 - E4 - E5 - E6 - E6R - E9 - E10 - E10R - E11 - E14
I
E16 - E17- E30 – E32
F3 - F4 - F5 - F6 - F6R - F10 - F10R - F11 - F14 – F16
F32
G3 - G4 - G5 - G6 - G6R - G10 - G10R - G11 - G12 -
G14 - G16 -G18 - G19
H6 - H10 - H11 - H30 – H38
J5 - J12 - J31-J40
B7 - B7R II
B25 B30 V
C8 - E8 VI
B15 VIII
H3 - H5 - H14 IX
APPENDIX 12
Branch Connections Tables
Type I
APPENDIX 12
Branch Connections Tables
Type II
APPENDIX 12
Branch Connections Tables
Type III
APPENDIX 12
Branch Connections Tables
Type IV
APPENDIX 12
Branch Connections Tables
Type V
APPENDIX 12
Branch Connections Tables
Type VI
APPENDIX 12
Branch Connections Tables
Type VII
APPENDIX 12
Branch Connections Tables
Type VIII
APPENDIX 12
Branch Connections Tables
Type IX
APPENDIX 13
Procedure for Internal Coating of Piping with Polyethylene
This appendix defines the fundamental process stages and the minimum
characteristics required for internal coating with Polyethylene for application in
seawater systems and flanged carbon steel piping:
1.2 - The preparation of the pipe's internal surface prior to application of the
internal coating should be at least Sa 2 1/2 (to the near white metal),
in accordance with the standard ISO 8501-1;
2 - The polyethylene coating applied to the internal surface of the carbon steel
piping should possess the following principal physical and mechanical
properties:
2.2 - Minimum tensile strength of 190, 120 and 59 Kg/cm2 and minimum
axial elongation of 260, 500 and 187% at -40, 23 and 60ºC
respectively. Tests performed in accordance with the standard ASTM
D638;
APPENDIX 13
Procedure for Internal Coating of Piping with Polyethylene
2.8 - The internal polyethylene coating allows a maximum work flow rate of 5
m/s when the water contains suspended solids, of the coarse sand
type, and 10 m/s when the water does not contain solids;
2.9 - The maximum permitted temperature for the use of the internal
polyethylene coating with water is 70ºC;
3 - The piping coated internally with polyethylene should satisfy the following
minimum requirements upon delivery:
3.1 - During the final inspection, first perform a visual check that there are no
discontinuities or projections along the entire surface of the pipe coated
with polyethylene, then perform an inspection using a Holiday Detector
with a 10 kV direct current. Any kind of discontinuities/sparks on the
internal surface and/or coated flange faces of the pipe will not be
accepted.
3.2 - The finish of the internal surface of the pipe coated with polyethylene
should be smooth and, the flange face should be sanded with fine
sandpaper until a smooth surface is achieved. The polyethylene coating
should cover the entire contact face used to seal the flanges.
APPENDIX 14
FULLY TIGHT VALVES (VET) DESCRIPTION
1 – PURPOSE
The purpose of this appendix is to list and describe the technical requirements of
approved VETs for use in Oil & Gas Production Facilities. The selection of these
valves shall be in accordance with DR-ENGP-II-P1-1.3.
• Set the VET tags for each material and pressure class specification;
• Set the VET tags in accordance with DR-ENGP-II-p1-1.3, which describes the
VET series, their selection criteria and application scope;
• Guide the project using the Table of Codes, item 7 of this appendix;
2 – DEFINITION
VETs (Fully Tight Valves) are the ones which require greater tightness guarantee
and lifetime.
VETs shall have specific constructive characteristics due to their installation
requirements. They are installed in pipes carrying flammable and toxic fluids,
important functions (SDV, BDV, ADV, HV and XV), to assure operational safety and
integrity for people and equipments.
VETs are valves with detailed constructive characteristics and high performance,
dispense the bench test during the construction and assembly stage since it is
attested, in the FAT, by PETROBRAS or its factory representant.
If the bench test is needed during the construction and assembly stage or the unit
operation, the requirements of this document shall be followed.
The specifications and VET TAGs are described in the Table of Codes, item 7 of
this document.
3 – WARRANTY PERIOD
All Fully Tight Valves shall be designed with mechanical characteristics that
guarantee tightness operation for, at least, 3 years under normal operation, without
needing internal parts maintenance, except for Fully Tight Valves serial 900, that are 6
years and for Fully Tight Valves serial 600, that are 1 year and a half.
Their projects shall also consider at least 500 complete cycles (opening and closing,
once every 2 days) without failure occurence, with maintenance only in the external
parts, without affecting their tightness characteristics (“tight shutoff"), except for Fully
Tight Valves serial 900, that are 1000 complete cycles.
Any repairs under warranty, costs of material and logistics will be paid by the
manufacturer.
The valve manufacturer shall formalize this warranty directly for PETROBRAS.
Suppliers shall issue testing certificates in full compliance with the datasheets
All tests to be performed on construction sites shall have their procedures previously
submitted to PETROBRAS approval.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 3 of 241
APPENDIX 14
FULLY TIGHT VALVES (VET) DESCRIPTION
All tests shall be monitored by PETROBRAS inspectors and by the company
contracted to supply the UEP (Stationary Production Unit).
Valves and lines involved in the test shall undergo a preliminary visual inspection to
verify the integrity of the valve pipe and the absence of internal fragments.
The pressure test to be applied on installed valves shall be 10% above the maximum
operating pressure of the service.
For VET SERIES "200" to "600", VET SERIES "300P" or "500P", the minimum
pressure test shall be 600 Kpag (minimum).
- The testing procedures for valves shall be in accordance with the requirements of
ASME B16.34 and all standards referenced in the valves datasheets.
- The tests shall be according to each kind of material, unless another specification
by the customer.
- Visual 100%
- For body and castle of cast iron and forged valves, ASME class 150 and 300, the
magnetic particle testing is required in 20% of each batch material.
- Visual 100%
- For body and castle of forged valves, class 900, 1500 and 2500, the test of
magnetic particles is required in 100% of each batch material.
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination in critical areas is required in 100% of each batch material.
- Visual 100%
- For body and castle of forged and casting valves, class 150 and 300, the Liquid
penetrant test is required in 20% of each batch material.
- For body and castle of forged valves, class 900, 1500 and 2500, the Liquid
penetrant test is required in 100% of each batch material.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 4 of 241
APPENDIX 14
FULLY TIGHT VALVES (VET) DESCRIPTION
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination is required in 100% in critical areas.
- Visual 100%
- For body and castle of forged and casting valves, class 150 and 300, the Liquid
penetrant test is required in 20% of each batch material.
- For body and castle of forged valves, class 900, 1500 and 2500, the Liquid
penetrant test is required in 100% of each batch material.
- For body and castle of casting valves, class 900, 1500 and 2500, the radiographic
examination is required in 100% in critical areas.
CONSIDERATION
- All valves specified for hydrogen sulfide service (NACE) shall be in strict
accordance with the requirements of the ISO 15156 (NACE MR175).
LEAKAGE TEST
Valve tightness tests and valve body hydrostatic test shall be according to ISO
14313 (API 6D) specification, along with the zero leakage criterium for all valves
including metal to metal in accordance with ISO 5208 “rate A”.
High pressure closing test closing is required for gate valves and globe valves.
The valve body hydrostatic test shall be 1.5 times the design pressure. The seat test
shall be 1.1 times the design pressure.
The average pH during the test shall be between 6.5 and 8.5.
Soft seat valves shall be actuated at least three times before starting the hydrostatic
test.
Petrobras or a representant shall carry out inspection of all valves described in this
technical specification at supply factories.
6 – ITEM COMMISSIONING
All Fully Tight Valves (VET) shall be part of the commissioning program, having
the same treatment as items of this document.
All Fully Tight Valves (VET) is mandatory the guide handling of maintenance and
operation of valve is inside an enclosure against the weather and fixed to the body of
the valve.
7 – Table of code
VET-1326
(2" - 12")
VET-1324
(2" - 12")
VET-856
(26" – 40")
VET-1505 VET-1506
(4" - 24") (26" - 48")
VET-079
B30
(1/2" - 1 1/2")
VET-1304
(2" - 12")
VET-713 VET-1328
(2" – 24") (2" - 12")
VET-1455
(3")
VET-1435 VET-1459
(1/2" – 2") (3")
VET-1435
(1/2" – 2")
VET-1402 VET-1436
E11
(1" – 2") (1" – 2")
VET-1402 VET-1436
(1/2" – 2") (1/2" – 2")
VET-024A
F4
(6" - 10")
VET-1406 VET-1439
(1/2" – 2") (1/2" – 2")
VET-1406 VET-1439
(1/2" – 2") (1/2" – 2")
VET-1440 VET-1456
(1/2" – 2") (3")
VET-1408 VET-1441
F11
(1/2" – 2") (1/2" – 2")
VET-1440
(1/2" – 2")
VET-1457 VET-1502
(3") (4" - 12")
VET-1407 VET-1440
(1/2" – 2") (1/2" – 2")
VET-1439
(1/2" – 2")
VET-1445
(1" – 2")
VET-1503
(4" - 12")
VET-1446
(1" – 2")
VET-1800P VET-1800CP
(4" – 12") (14" – 20")
VET-1700 VET-1701
(6" - 12") (14" - 20")
Espec B3 B3
Tag: VET-001 VET-001A
Type: Ball valve Ball valve
NPS: 2" – 4" 2" – 4"
Standard: ISO 14313 (API 6D) (1) ISO 14313 (API 6D) (1)
fire tested ISO 10497 (2); monogram
Certificate:
API fire tested ISO 10497 (2); monogram API
End/finishing: flange ASME B16.5; raised face (RF) flange ASME B16.5; raised face (RF)
Class: 150 150
Body material: A 351 Grade CF8M A 351 Grade CF8M
Body type: split body split body
vent anti-ejection system starter relief vent anti-ejection system starter relief hole
Vent/drain:
hole opening to atmosphere opening to atmosphere
Drain hex head plug threaded hex head plug threaded
Ball mounting: trunnion trunnion
Bore type: full bore full bore
Obturator (ball): AISI 316 AISI 316
Spring seat: Inconel® X750 Inconel® X750
Seat insert: PTFE reinforced with 25% of carbon PEEK® XP 108
Temperature: -46°C to 150°C -46°C to 210°C
O’rings seal: N/A N/A
Lip seal: PTFE + Elgiloy PTFE + Elgiloy
Stem/trunnion
A 182 Grade F 316L
material: A 182 Grade F 316L
Stem: blow out proof stem, double seal blow out proof stem, double seal
Bushing: DU® DU®
Operator: wrench (lever) operator wrench (lever) operator
Test: According ISO 14313 (API 6D) item 11 According ISO 14313 (API 6D) item 11
According annex; B3- low-pressure gas
seat testing between 0.5 bar and 1.0 bar According annex; B3-low-pressure gas seat
using air or nitrogen as the test medium; testing between 0.5 bar and 1.0 bar using
According annex; B3- low-pressure gas air or nitrogen as the test medium;
Suplementary Test seat testing of 5.5 bar ± 0.7 bar using air According annex; B3- low-pressure gas
According ISO 14313 or nitrogen as the test medium; B5 - seat testing of 5.5 bar ± 0.7 bar using air or
anti-static testing;B6- torque/thrust nitrogen as the test medium; B5 - anti-static
(API 6D) Annex b:
testing;B6- torque/thrust functional
functional testing;B7- drive train strength testing;B7- drive train strength test,
test, sampling de 5%; B8- cavity relief sampling de 5%; B8- cavity relief testing,
testing, sampling de 5%.; B10- Double sampling de 5%.; B10- Double block and
block and bleed; bleed;
Marking: According MSS SP-25 According MSS SP-25
General requirement: locking device; anti-static device locking device; anti-static device
Bolt/nut: manufacturer standard manufacturer standard
100% visual casting According MSS 100% visual casting According MSS SP-55;
Test:
SP-55; dye penetrant in machined parts dye penetrant in machined parts
1 - it shall be According ASME B16.34 and
ASME section VIII standard
1 - it shall be According ASME B16.34 2 - All valve components shall be fire tested
and ASME section VIII standard 3-This specification shall also fulfill the
2 - All valve components shall be fire items listed on the description of appendix
Notes: tested 14;
3-This specification shall also fulfill the 4- Ball shall be coated with Electroless
items listed on the description of Nickel Planting (ENP) with minimum
appendix 14; thickness 75 microns according standard
ASTM B117.
1 - it shall be According ASME B16.34 and ASME 1 - it shall be According ASME B16.34 and
section VIII standard ASME section VIII standard
2 - All valve components shall be fire tested 2 - All valve components shall be fire tested
Notes: 3-This specification shall also fulfill the items listed 3-This specification shall also fulfill the items
on the description of appendix 14; listed on the description of appendix 14;
4-Acessories shall have deposition of material 4- Ball shall be coated with Electroless Nickel
inconel with 3mm thickness. Planting (ENP) with minimum thickness 75
microns according standard ASTM B117.
5- Acessories shall have deposition of material
inconel with 3mm thickness.
Test: dye penetrant in machined parts 100% visual casting According MSS SP-55; dye
penetrant in machined parts
Test: dye penetrant in machined parts 100% visual casting According MSS SP-55; dye
penetrant in machined parts
1 - it shall be According ASME B16.34 and 1 - it shall be According ASME B16.34 and
ASME section VIII standard ASME section VIII standard
2 - All valve components shall be fire tested 2 - All valve components shall be fire tested
3-This specification shall also fulfill the items 3 - Acceptable ASTM A 105; 4-This
listed on the description of appendix 14; specification shall also fulfill the items listed on
4- Ball shall be coated with Electroless Nickel the description of appendix 14.
Notes: Planting (ENP) with minimum thickness 75 5- Ball shall be coated with Electroless Nickel
microns according standard ASTM B117. Planting (ENP) with minimum thickness 75
5-Acessories must be inmaterial inconel 718, if microns according standard ASTM B117.
not the acessories, the device screw fastening for 6- Acessories must be inmaterial inconel 718, if
valve and internal coated must have deposition of not the acessories, the device screw fastening for
material inconel with 3mm thickness on the less valve and internal coated must have deposition of
thickness point. material inconel with 3mm thickness on the less
thickness point..
Bore type: full bore piggable - internal diameter (ID) valve shall be
defined by Project Engineer
Obturator (ball): A 995 Grade 4A (UNS J92205) A 995 Grade 4A (UNS J92205)
Spring seat: Inconel® X750 Inconel® X750
Seat insert: PEEK® XP 108 PEEK® XP 108
Temperature: 0°C to 150°C 0°C to 150°C
O’rings seal: Viton GLT Viton GLT
Lip seal: N/A N/A
Stem/trunnion material: A 182 Grade F 316 A 182 Grade F 316
Stem: blow out proof stem, double seal blow out proof stem, double seal
Bushing: DU® DU®
Operator: handwheel gear operator handwheel gear operator
Test: according ISO 14313 (API 6D) according ISO 14313 (API 6D)
According annex; B3- low-pressure gas seat According annex; B3- low-pressure gas seat
testing between 0.5 bar and 1.0 bar using air or testing between 0.5 bar and 1.0 bar using air or
nitrogen as the test medium; According annex; nitrogen as the test medium; According annex;
B3- low-pressure gas seat testing of 5.5 bar ± 0.7 B3- low-pressure gas seat testing of 5.5 bar ± 0.7
Test complement according
bar using air or nitrogen as the test medium; B5 - bar using air or nitrogen as the test medium; B5 -
ISO 14313 (API 6D):
anti-static testing;B6- torque/thrust functional anti-static testing;B6- torque/thrust functional
testing;B7- drive train strength test, sampling de testing;B7- drive train strength test, sampling de
5%; B8- cavity relief testing, sampling de 5%.; 5%; B8- cavity relief testing, sampling de 5%.;
B11- Double Piston Effect; B11- Double Piston Effect;
Marking: according MSS SP-25 according MSS SP-25
The external seat have self relief feature and the The external seat have self relief feature and the
internal seat have double piston effect (DPE) internal seat have double piston effect (DPE)
General requirement:
feature; feature;
locking device; anti-static device locking device; anti-static device
Bolt/nut: manufacturer standard manufacturer standard
100% visually casting according MSS SP-55; 100% visually casting according MSS SP-55;
Test:
dye-penetrant in machined parts dye-penetrant in machined parts
Bore type: full bore piggable - internal diameter (ID) valve shall be
defined by Project Engineer
Obturator (ball): UNS S17400 UNS S17400
Spring seat: Inconel® X750 Inconel® X750
Seat insert: PEEK® XP 108 PEEK® XP 108
Temperature: -29°C to 150°C -29°C to 150°C
O’rings seal: N/A N/A
Lip seal: PTFE + Elgiloy PTFE + Elgiloy
Stem/trunnion material: A 182 Grade F 316 A 182 Grade F 316
Stem: blow out proof stem, double seal blow out proof stem, double seal
Bushing: DU® DU®
Operator: handwheel gear operator handwheel gear operator
Test: according ISO 14313 (API 6D) according ISO 14313 (API 6D)
According annex; B3- low-pressure gas seat According annex; B3- low-pressure gas seat
testing between 0.5 bar and 1.0 bar using air or testing between 0.5 bar and 1.0 bar using air or
nitrogen as the test medium; According annex; nitrogen as the test medium; According annex;
B3- low-pressure gas seat testing of 5.5 bar ± 0.7 B3- low-pressure gas seat testing of 5.5 bar ± 0.7
Test complement according
bar using air or nitrogen as the test medium; B5 - bar using air or nitrogen as the test medium; B5 -
ISO 14313 (API 6D):
anti-static testing;B6- torque/thrust functional anti-static testing;B6- torque/thrust functional
testing;B7- drive train strength test, sampling de testing;B7- drive train strength test, sampling de
5%; B8- cavity relief testing, sampling de 5%.; 5%; B8- cavity relief testing, sampling de 5%.;
B11- Double Piston Effect; B11- Double Piston Effect;
Marking: according MSS SP-25 according MSS SP-25
The external seat have self relief feature and the The external seat have self relief feature and the
internal seat have double piston effect (DPE) internal seat have double piston effect (DPE)
General requirement:
feature; feature;
locking device; anti-static device locking device; anti-static device
Bolt/nut: manufacturer standard manufacturer standard
100% visually casting according MSS SP-55; 100% visually casting according MSS SP-55;
Test:
dye-penetrant in machined parts dye-penetrant in machined parts
Bore type: full bore piggable - internal diameter (ID) valve shall be
defined by Project Engineer
Obturator (ball): A 995 Grade 4A (UNS J92205) A 995 Grade 4A (UNS J92205)
Spring seat: Inconel® X750 Inconel® X750
Seat insert: PEEK® XP 108 PEEK® XP 108
Temperature: 0°C to 150°C 0°C to 150°C
O’rings seal: N/A N/A
Lip seal: PTFE + Elgiloy PTFE + Elgiloy
Stem/trunnion material: A 182 Grade F 316 A 182 Grade F 316
Stem: blow out proof stem, double seal blow out proof stem, double seal
Bushing: DU® DU®
Operator: handwheel gear operator handwheel gear operator
Test: according ISO 14313 (API 6D) according ISO 14313 (API 6D)
According annex; B3- low-pressure gas seat According annex; B3- low-pressure gas seat
testing between 0.5 bar and 1.0 bar using air or testing between 0.5 bar and 1.0 bar using air or
nitrogen as the test medium; According annex; nitrogen as the test medium; According annex;
B3- low-pressure gas seat testing of 5.5 bar ± 0.7 B3- low-pressure gas seat testing of 5.5 bar ± 0.7
Test complement according
bar using air or nitrogen as the test medium; B5 - bar using air or nitrogen as the test medium; B5 -
ISO 14313 (API 6D):
anti-static testing;B6- torque/thrust functional anti-static testing;B6- torque/thrust functional
testing;B7- drive train strength test, sampling de testing;B7- drive train strength test, sampling de
5%; B8- cavity relief testing, sampling de 5%.; 5%; B8- cavity relief testing, sampling de 5%.;
B11- Double Piston Effect; B11- Double Piston Effect;
Marking: according MSS SP-25 according MSS SP-25
The external seat have self relief feature and the The external seat have self relief feature and the
internal seat have double piston effect (DPE) internal seat have double piston effect (DPE)
General requirement:
feature; feature;
locking device; anti-static device locking device; anti-static device
Bolt/nut: manufacturer standard manufacturer standard
100% visually casting according MSS SP-55; 100% visually casting according MSS SP-55;
Test:
dye-penetrant in machined parts dye-penetrant in machined parts
Bore type: full bore piggable - internal diameter (ID) valve shall be
defined by Project Engineer
Obturator (ball): UNS S17400 UNS S17400
Spring seat: Inconel® X750 Inconel® X750
Seat insert: PEEK® XP 108 PEEK® XP 108
Temperature: -29°C to 150°C -29°C to 150°C
O’rings seal: Viton GLT (5) Viton GLT (5)
Lip seal: - -
Stem/trunnion material: A 182 Grade F 316 A 182 Grade F 316
Stem: blow out proof stem, double seal blow out proof stem, double seal
Bushing: DU® DU®
Operator: handwheel gear operator handwheel gear operator
Test: according ISO 14313 (API 6D) according ISO 14313 (API 6D)
According annex; B3- low-pressure gas seat According annex; B3- low-pressure gas seat
testing between 0.5 bar and 1.0 bar using air or testing between 0.5 bar and 1.0 bar using air or
nitrogen as the test medium; According annex; nitrogen as the test medium; According annex;
B3- low-pressure gas seat testing of 5.5 bar ± 0.7 B3- low-pressure gas seat testing of 5.5 bar ± 0.7
Test complement according
bar using air or nitrogen as the test medium; B5 - bar using air or nitrogen as the test medium; B5 -
ISO 14313 (API 6D):
anti-static testing;B6- torque/thrust functional anti-static testing;B6- torque/thrust functional
testing;B7- drive train strength test, sampling de testing;B7- drive train strength test, sampling de
5%; B8- cavity relief testing, sampling de 5%.; 5%; B8- cavity relief testing, sampling de 5%.;
B11- Double Piston Effect; B11- Double Piston Effect;
Marking: according MSS SP-25 according MSS SP-25
The external seat have self relief feature and the The external seat have self relief feature and the
internal seat have double piston effect (DPE) internal seat have double piston effect (DPE)
General requirement:
feature; feature;
locking device; anti-static device locking device; anti-static device
Bolt/nut: manufacturer standard manufacturer standard
100% visually casting according MSS SP-55; 100% visually casting according MSS SP-55;
Test:
dye-penetrant in machined parts dye-penetrant in machined parts
APPENDIX 15
Isolating Joint
APPENDIX 15
Isolating Joint
APPENDIX 15
Isolating Joint
Appendix 16
Welding Requirements
Index
Section II - Welding Qualification for Inconel® 625 “Weld Overlay” Clad pipe pg.04
Appendix 16
Welding Requirements
General Scope
This appendix establishes the minimum mandatory requirements for design, production,
inspection, testing and acceptance of welding.
2 faces + 2 roots, or 4
Bend testing ASME IX ASME IX
lateral
Appendix 16
Welding Requirements
OBS:
The consumable's composition should contain between 2% and 3.5% Ni above of the base
metal.
2 – WELDER QUALIFICATION
Appendix 16
Welding Requirements
Section II - Welding Qualification for Inconel® 625 “Weld Overlay” Clad pipe.
1.0- Scope
This section presents the welding requirements for Inconel 625 combined with carbon steel
pipes in the form of “weld overlay”. Upon completion of the welding process, the minimum
thickness of the deposition of Inconel 625 should be 3.0 mm.
Appendix 16
Welding Requirements
ASTM G 48: Standard Test Methods for Pitting and Crevice Corrosion
resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride
Solution;
AWS Code;
DNV OS F101: Submarine pipeline systems;
ISO 3834-2: Quality requirements for fusion welding of metallic materials-part 2:
comprehensive quality requirements;
ISO-15590-1 Induction Bending;
ISO-8501-1: Preparation of steel substrates before application of paints and
related products - Visual assessment of surface cleanliness.
NACE MR 0175/ISO 15156: petroleum and natural gas industries - materials for
use in h2s-containing environments in oil and gas production;
3.0- Definitions
For the purposes of this appendix the definitions indicated in items 3.1 to 3.2 are adopted.
3.1. Clad/Cladding
4.1. For welded overlay surface involving inconel 625 and carbon steels (weld overlay
process), shall be used Gas -Tungsten-Arc (GTAW) and GTAW-Hot Wire (GTAW-Hot Wire-
pipe clad, mechanized process).
5.1. Materials shall be provided with the respective certificates of fabrication according to the
applicable standards. For welding consumables (wire and gas), the requirements listed below
shall be applied:
Appendix 16
Welding Requirements
5.1.1.2. Classifications: ER Ni Cr Mo-3;
figure 1
6.1. Manufacturing procedure specification for CRA Cladded Pipe and Fitting Internal Carbon
Steel Pipe with UNS N06625.
1.0 CARBON STEEL PIPE, Verification of Material Test CS Base Pipe for cladding:
FITTING AND WELD Certificates. (MTCs)
CONSUMABLE RECEIPT Inspection of physical condition, & Certificate to EN10204 3.1
identification (formerly EN10204 3.1.B) & in
accordance with material code.
CRA weld overlay consumable
AWS A5.01 SCH H (analysis of
heat) ERNiMoCr-3 Alloy UNS
N06625
Appendix 16
Welding Requirements
Appendix 16
Welding Requirements
reported for information.
Base material used for the weld NOTE: As required by B31.3 per
qualification shall be from same 328.2, test weldments shall be
material grouping as API 5L and made based on the material
ASTM A 694 F60 (ASME IX QW- groupings taken from ASME IX
422 QW-422
Appendix 16
Welding Requirements
testing as outlined above. 5L-X60 pipe-to-pipe butt welds
as well as API 5L-X60 – ASTM
A694 F60 pipe-to-flange butt
welds.
Appendix 16
Welding Requirements
reported for information.
4. ASME IX QW-195.2
4. Liquid Penetrant Examination of Acceptance Criteria (also ASME
the corrosion resistant alloy VIII Div 1 App 8).
overlay in accordance with QW-
195 (per ASME V Article 6 or The following are unacceptable:
ASTM E165). (i) any relevant linear indications
(ii) any relevant rounded
indications
greater than 4.8mm
(iii) four or more relevant
rounded
indications in a line separated by
1.6mm or less (edge to edge).
Appendix 16
Welding Requirements
7.0 DRYING CS PIPE Air drying of CS pipe internal. The clean air used for drying CS
pipe shall have a dew point that
is at least 4ºC higher than the
ambient air dew point measured
local to pipe at blast station.
9.0 WELDING 1. Internally weld complete pipe 1. Pipe internally overlayed fully
9.1 Production Welding length. length.
2. All variables monitored by 2. All variables within limits
welding operators and welding permitted by WPS.
inspectors.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/042/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 12 of 24
Appendix 16
Welding Requirements
3. Welding wire consumable 3. Welding wire identity to be
checked prior touse (1.2mm recorded and checked against
diameter solid Alloy 625 wire). batch certificate.
9.2 Repair 1. Area for repair defined by NDE. 1. Defined by LPI inspection (see
10.0).
Appendix 16
Welding Requirements
1. 100% Visual Inspection of all 1. Smooth overlay surface fully &
pipes and video camera continuously welded.
examination of all internal weld
surface.
2. Liquid Dye Penetrant test all 2. API 6A PSL2 for surface NDE.
accessible areas of weld overlay The following acceptance criteria
cladding all pipes. Water washable apply:
penetrant permissible. a. No relevant linear indications
b. No relevant rounded indication
with major dimension equal or
greater than 5 mm.
c. Four or more relevant rounded
indications in a line separated by
1.6mm or less (edge to edge)
are unacceptable.
d. No relevant indications in
pressure contact
sealing surfaces (e.g. flange
gasket faces).
Pipe Body-External
Appendix 16
Welding Requirements
Where butt welds are required, Acceptance criteria for girth weld
100% radiographic examination of radiography to be as per ASME
butt welds (i.e. girth welds) in B31.3 (normal fluid service
accordance with ASM V Article 2.
Appendix 16
Welding Requirements
If internally washed with potable
water, the pipe shall be dried by air
blast using clean, dry air.
11.0 TESTING DURING The following production lot testing Acceptance Criteria
PRODUCTION shall be conducted when the
welding consumable heat
changes. Test samples shall be
cut from a section of clad pipe or
equivalent test piece.
Appendix 16
Welding Requirements
below).
Appendix 16
Welding Requirements
substitute.
PMI testing may be performed
either during or after production
cladding operations.
Appendix 16
Welding Requirements
cladding is continuous and that no
base metal is exposed to fluids in
service.
Appendix 16
Welding Requirements
7.0- Recommended Practices for “Butt welding joints” procedure specification (WPS).
This item establishes the recommended practices for prepare and qualify the butt welding
joints procedure specification (WPS). However, all welding documents shall be prepared and
qualified by a welding inspector qualified (see annex “A”).
7.1. For welding pipe to pipe or pipe to fittings joint´s (butt-welding joint´s), can be used gas -
tungsten-arc (GTAW - manual process) and SMAW process.
Qualification of GTAW / SMAW Butt Weld WPS to be performed using multiple layer
ERNiMoCr-3 welding consumable in accordance with the requirements of ASME B31.3 and
ASME IX.
Base material used for the weld qualification shall be from same material grouping as API 5L
and ASTM A694 F60 (ASME IX QW-422).
Note: Change of filler metal brand name and manufacturing location are not considered
essential variables.
7.2. Consumable
Classifications: ER Ni Cr Mo-3;
7.3. Gas
Appendix 16
Welding Requirements
Acceptance Criteria
If any testing additional to the under mentioned requirements is undertaken during testing
of the actual procedure qualification, the additional test results can be included in the
resultant final PQR but strictly for information only.
NOTE: As required by ASME B31.3 per 328.2, test weldments shall be made based on
the material groupings taken from ASME IX, QW-422 Base material selected for butt weld
procedure qualification testing shall follow ASME IX as per QW-420.1 and QW-420.2. In this
case, base material for weld procedure qualification will be S-Number 1 Group 2 (e.g. API
5L-X60/X65).
This will qualify API 5L pipe-to-pipe butt welds as well as API 5L – ASTM A694 pipe-to-
flange butt welds.
Appendix 16
Welding Requirements
1.0- Scope
This item establishes the recommended practices for prepare and qualify the butt welding
joints procedure specification (WPS) for ASTM A-333 Gr8, ASTM A 420 Gr WPL8 and
ASTM A 522 Type I, base materials.
However, all welding documents shall be prepared and qualified by a welding inspector
qualified (see annex “A”).
For better welding results, the chemical composition shall be as given in Table.
The better properties were obtained with the Quenched and Tempered cool in water heat
treatment, for base materials.
According ASTM A-333 Gr8, ASTM A 420 Gr WPL8 and ASTM A 522 Type I, standards.
Appendix 16
Welding Requirements
6.0- Recommended Practices for “Butt welding joints” procedure specification (WPS).
This item establishes the recommended practices for prepare and qualify the butt welding
joints procedure specification (WPS). However, all welding documents shall be prepared and
qualified by a welding inspector qualified (see annex “A”).
6.1- For welding pipe to pipe or pipe to fittings joint´s (butt-welding joint´s), can be used gas -
tungsten-arc (GTAW - manual process) and SMAW process.
Qualification of GTAW / SMAW Butt Weld WPS to be performed using multiple layer
ERNiMoCr-3 welding consumable in accordance with the requirements of ASME B31.3 and
ASME IX.
Note: Change of filler metal brand name and manufacturing location are not considered
essential variables.
(1) Remove scale, rust, and other dirt from welding grooves beforehand by grinding or other
appropriate means.
(2) Use no preheat and control interpass temperatures at 150°C or lower.
(3) Minimize welding currents and welding speeds to prevent hot cracking.
(4) Use no magnetic power crane because 9%Ni steel is likely to be magnetized.
SMAW
(1) Re-dry covered electrodes by 200-250°C for 30-6 0 minutes before use.
(2) Keep the arc length as short as possible.
(3) Use Heat Input 1,30 up to 1,86 kJ/mm
Appendix 16
Welding Requirements
GTAW
(1) Use multi-pass welding because the use of single-pass welding may cause a decrease of
weld metal strength affected by the dilution from the base metal.
(2) Use Heat Input 1,56 up to 4,00 kJ/mm
7.2. Consumable
Classifications: ER Ni Cr Mo-3.
7.3. Gas
Appendix 16
Welding Requirements
A.1. Scope
A.1.1. This ANNEX establishes required conditions for Personnel Qualification, used at
fabrication and assembly of piping, according to the contractual scope.
a) Welding inspectors – in order to perform welding inspection in Brazil, qualification
and certification shall be by the Brazilian System of Welding Inspector Qualification
and Certification (FBTS), according to standard NBR 14842. For services rendered
abroad, qualification and certification shall be according to that established above or
by independent international entities that meet requirements in standards EN 45013
or ISO/IEC 17024, and for level 2 inspectors, in the main applicable standard as
well, whereas in this case PETROBRAS’ previous approval is required.
A.1.1.1. Regarding qualification of welders and welding operators, the CONTRACTED
PARTY shall meet the following directives:
b) Welders and welding operators shall be qualified by a level 2 welding inspector,
according to the equipment’s project standard. If the qualification standard of these
professionals is not foreseen in the specifications, standard ASME Section IX shall
be used for this purpose. Tackers are not allowed to be used, even when qualified
according to technical standards;
c) Welders or welding operators who are have been performing welding activities
without interruption for over three months, and were qualified for other jobs at
PETROBRAS, can be used, so long as they present qualification records,
accompanied by their respective individual certificates (original documents), properly
approved by a qualified welding inspector and endorsed by PETROBRAS Inspection
of previous jobs;
d) Welders or welding operators who have not performed welding for three or more
months, or who have not had their welds tested by radiography or ultrasonic, must
undergo retraining and re-qualification.
A.1.1.2. The contracted party shall present to PETROBRAS inspection, before beginning of
activities, the list of operators and inspectors qualified to perform and inspect the services.
A.1.1.3. Welders and welding operators who present a biweekly repair rate above the
following established values, shall be retrained and re-qualified:
- 2.5% (two point five percent) or 75 (seventy-five) mm in 3 (three) meters of tested
welds, when the rate is calculated by defect length; or
- 10% (ten percent) or 2 (two) radiographies for every 20 (twenty) radiographies
examined sequentially, when the rate is calculated by number of radiographies.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
1 - OBJECTIVE
1.1 - This Appendix contains the minimum mandatory requirements for design,
production, inspection and acceptance of stainless steel duplex and
superduplex cast valves (UNS J92205, UNS J93404 and UNS J93380), made
using no bake sand foundry process, to be used in PETROBRAS Exploration
and Production Units.
1.2 – This Appendix is applicable to ball, gate, globe and check type flanged valves,
as defined in the Specifications (Spec’s) B16, B12, B13, C16, C12, C13, E16,
G16, G16P, G12, G12P and J12.
1.3 – This appendix is applicable for class 150 to 1500 and 10000 PSIG valves with
nominal diameter of 2 inches or higher.
2 - COMPLEMENTARY DOCUMENTS
2.1 – The documents listed below are valid for the present appendix:
ASME SEC VIII DIV 1 SUB A General Requirements for All Methods of
PT UG Construction and All Materials
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
3 - DEFINITIONS
3.1 – PITTING RESISTANCE EQUIVALENT NUMBER (PREN): Empiric Mathematical
Formula that correlate resistance to localized corrosion, in environments
containing chlorides, with the amounts alloying elements in the steel that
contribute to increase this resistance. For the super-duplex steel the PREN ≥ 40.
PREN = %Cr + 3.3 x %Mo + 16 x %N.
3.1.1 – PILOT CASTING: Any casting, that is the first of its model or of a new or
modified project, using the same casting procedure (same casting) as the ones it
represents.
4 - DOCUMENTATION
4.1 – The Manual of each valve shall contain all the certificates related to each piece
that is part of the said valve. These certificates are related to:
- chemical requirements;
4.2 – The manual shall contain Welding Procedure Specifications (WPS) for defect
repairing, duly approved by PETROBRAS or by a Classification Society indicated
by PETROBRAS.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
- Cavity mapping for bigger repairs for each part of the valve and;
- The Welding Registration Report (RRS) of the repairs of each part of the
valve.
5 - CHEMICAL REQUIREMENTS
5.1 – The duplex steel composition used for the manufacturing of the cast valve shall
be in accordance with 4A degrees (UNS J92205 or CD3MN) of ASME SA-995 or
ASTM A 995 standards, to attend the Specifications of B16, C16, E16, G16 and
G16P.
5.2 - The superduplex steel composition used for the manufacturing of the cast valve
shall be in accordance with 5A degrees (UNS J93404 or CE3MN) of ASME SA-
995 or ASTM A 995 standards, to attend the Specifications of B12, C12, G12,
G12P and J12.
5.3 – The superduplex steel composition used to manufacture the cast valves shall be
in accordance with the 6A degrees (UNS J93380 or CD3MWCuN) of the ASME
SA-995 or ASTM A 995 standards, to attend the Espec’s B13 and C13.
5.4 – The representative sample of the chemical requirements of the valve shall be
collected from the pouring ladle.
5.5 – A representative sample for carbon, sulfur and nitrogen contents shall be
collected from the furnace before pouring into the ladle.
5.6 – The addition of Niobium to the cast shall be avoided. The maximum Niobium
content admitted shall be of 0.060% at the chemical requirements of the cast.
5.7 – Adding Aluminum to the run shall be avoided. The maximum content of
Aluminum admitted to the final chemical requirements shall be of 0.030%.
5.8 – The levels of Nitrogen shall preferably be in the range of 0.20 to 0.25% for the
two degrees subject of this Appendix.
5.9 – All consumables for the welding process shall have certification of their chemical
requirements guaranteeing the Maximum levels of Niobium of 0.060%.
5.10 – The chemical analysis of the elements shall be made in calibrated equipment
using certified standards.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 5 of 11
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
5.11 – When more than one ladle is used for one mold, the metal founded in each
ladle shall be in accordance with the chemical specifications for the required
level.
6 - HEAT TREATMENT
6.1 – The procedure for solubilization heat treatment used to the superduplex steel for
the production of the cast valves shall be in accordance with the procedure for
heat treatment defined for 5A degrees (UNS J93404 or CE3MN) and 6A (UNS
J93380 or CD3MWCuN) of ASME SA-995 or ASTM A 995 standards.
6.2 – Only solubilization heat treatment could be used in the production of the
superduplex steel no other heat treatment could be used to produce it.
6.3 – The maximum number of solubilization heat treatments allowed for a single
valve is limited to three (03) at foundry and one (01) at machining shop. If more
heat treatments are needed, PETROBRAS shall be consulted for the
authorization of such additional heat treatments.
6.4 – Not any valve shall be supplied as cast without solubilization heat treatments.
6.5 - All heat treatments shall be monitored through thermocouples in the heat
charge and in the furnace, generating a report shat shall be annexed to the
manual of the valve.
6.6 – Not any repairs using welding shall be executed on the piece before its prior
submission to heat treatment.
6.8 – The soaking time depends on the prior experience of the manufacturer, but shall
be so that guarantees full solubilization of the inter-metallic phases and the
precipitates through the thickest dimension of the piece without causing
dimensional distortions.
6.9 – The Pilot Casting shall have the possibility of extracting a test specimen from
the body of the piece for metallographic tests, which can be in any direction
(longitudinal or transversal), representing a central session of the thickest part of
the piece, as in the supplementary pre-requisite S26.2 of ASTM A703 standard,
to verify the effectiveness and adjustment of the soaking time of the
solubilization heat treatment. The results of this metallographic shall be part of
the manual of each valve.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
6.10 – The result of the metallographic test shall indicate absence of inter-metallic
phases and undesired precipitates – notably, the sigma phase, carbides and
nitrates – in a 200X magnification, as well as indicate a level of ferrite in the
range of 35 to 55%, according to ASTM E 562 standard.
6.11 – For each casting that weighs more than 300 kg, specimens for mechanical
and metallurgical tests shall be attached, as in ASTM A 703. These test
specimens shall remain attached to the casting until the last thermal treatment.
For pieces weighing less than 300 kg, a test specimen per run is accepted.
7.1 – The mechanical and metallurgical tests shall be done after the last the
solubilization heat treatment before machining the casting.
7.2 – The mechanical tests to be executed are those of tension, hardness and impact
(Charpy-V). These tests shall be executed according to ASTM A 370 standard.
7.3 – The test specimens shall be obtained from cast test blocks, as in ASTM A703.
These blocks shall go through all the solubilization heat treatments before
collecting the specimens for analysis.
7.4 - One (01) specimen shall be extracted for the tension test. The minimum
acceptable values are set in Table 1 (ASME SA-995 or ASTM A 995).
Grade 4A 5A 6A
UNS J92205 J93404 J93380
Tensile Strength, ksi [MPa] {kg/mm²} 90 [620] {63} 100 [690] {70} 100 [690] {70}
Yield Strengh (0,2%), ksi [MPa] {kg/mm²} 60 [414] {42} 75 [515] {53} 65 [450] {46}
Elongation in 2” [50 mm], % 25 18 25
Table 1 – Minimum values for tension tests.
7.5 – Three (03) test specimens shall be collected for the impact tests (Charpy-V).
The tests shall be run at a temperature of - 46oC. The minimum values of
absorbed energy shall be of 45J for an average of the three test specimens and
35J for each one of the test specimens.
7.6 – The hardness tests shall be run on a test specimen collected from a test block,
in a point representative of the central part of the thickest part of the casting,
according to the supplementary requirement S26.2 of ASTM A703 standard, that
has direct contact with the process fluid. The maximum hardness shall not be
above 32 HRC (or 310 HB or 330 HV10), considering the average of three
measurements. Castings that are lighter than 300 kg shall be tested individually
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
and shall render specific hardness values less or equal to the Pilot Casting on
the surface.
7.7 – A test specimen shall be collected from the Pilot Casting, to run the corrosion
tests according to ASTM G48 Method A. The test shall be run for 24 hours at a
o
temperature of 50 C. The acceptance criteria are just for 5A degrees (UNS
J93404 or CE3MN) and 6A degrees (UNS J93380 or CD3MWCuN):
- No pites located at 20 X magnification;
- Loss of mass lower than 4.0 g/m².
7.8 – The test to determine the levels of ferrite shall be run in accordance with ASTM
E 562. The test specimen to run this test shall be collected from a cast test block
connected to a casting, that would represent a certain run. The acceptable range
is 35 to 55% of ferrite.
8 - INSPECTION
8.1 – VISUAL
8.1.1 – The visual inspection shall be made on each casting before and after each
solubilization heat treatment, after pre-machining (whenever is the case) and
the final machining. All castings that make up the valves of the same
manufacturing order shall undergo visual inspection.
8.1.2 – All accessible surfaces, internal and external, shall be visually examined,
comparing acceptable discontinuities and superficial finishing attending the
standards set by MSS SP-55 or comparison standards of Steel Casting
Research and Trading Association (SCRATA) adopted in ASTM A802, or
other standard considered equivalent by a set deal between the manufacturer
of the valve and PETROBRAS.
8.1.3 – The levels of acceptance for visual inspections are set in ASTM A802, and
are:
8.1.4 – All castings that present in one or more surfaces the following defects,
independent of how serious or how extensive the defect is, or weather it
allows repairs using welding or not, shall be considered UNACCEPTABLE:
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
- Shift – discontinuity due to displacement of contact edges of the molding
boxes;
- Shut metal – discontinuity due to the encounter of two currents of metal that
have not been well mixed;
- Rat tail – depression on the surface of the piece caused by waves or failure
in the mold surface;
8.2.2 – The inspection using penetrating liquid shall be run on every produced
casting, on all accessible surfaces (internally and externally), after each
solubization heat treatment, after the pre-machining (whenever is the case)
and the final machining. All castings that make up the valves of the same
order shall undergo inspection using Penetrating Liquid.
8.2.3 – The inspection using Penetrating Liquid shall run in accordance with ASTM E
165.
8.2.4 – The stains of the Penetrating Liquid after the application of the developer are
called “indications”.
- Linear when the relation between length and width is bigger or equal to 3;
- Non-linear when the relation between length and width is less than 3;
8.2.6 – The criteria of acceptance by the inspection by penetrating liquids are shown
in ASME SEC VIII DIV 1 APPENDIX 7.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
8.3 – RADIOGRAPHY
8.3.1 – The radiographic inspection shall be executed by Level 2 inspectors, qualified
by the “Sistema de Nacional de Qualificação e Certificação” (National System
of Qualification and Certification) in Non-Destructive Tests (SNQC/END), or by
another certification means considered equivalent by agreement between the
manufacturer of the valve and PETROBRAS.
8.3.2 – The radiographic inspection shall be run on the Pilot Casting (body, cap and
shutter), after the final solubilization heat treatment. In case or pieces included
in classes 900, 1500 and 10000 PSIG, it is mandatory to radio graphically
inspect of 100% of the final pieces, in the critical regions defined in ASME
B16.34.
8.3.5 – If all indications were classified as ACCEPTABLE no other piece equal to the
Pilot Casting needs to be radiographed.
8.3.6 – If one or more conditions were classified UNACCEPTABLE the Pilot Casting
shall be fixed or scrapped and another piece shall be radiographed. If the
second piece were approved, not any equal piece needs to be radiographed.
However, if the second piece also presented indications classified as
UNACCEPTABLE all pieces equal to the Pilot Casting of the order shall be
radiographed in the areas rejected for the Pilot Casting and for the second
casting. The second casting and the subsequent piece of the order shall be
repaired whenever possible.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
9 - REPARES
9.1 - The reparations of the defects found in the various inspections shall be corrected
by welding.
9.2 - The reparations shall have a specific Welding Procedure Specification (WPS),
duley approved by PETROBRAS or by the Classification Society indicated by
PETROBRAS. This WPS shall be based on ASTM A 488.
9.3 - The WPS and the qualification of the welder shall follow the approval criteria set
in Appendix 16 of this specification.
9.4 - The execution of the repair job shall be accompanied by a Level I welding
inspector.
9.5 - The surface to be repaired shall be inspected visually and by penetrant liquid
and depending on the extension of the defect, by radiography, before submitting
it to the welding procedures.
9.6 - After welding, the repair shall be inspected visually and by penetrant liquid and
depending on the extension of the repair, by radiography. All the inspections
shall obey the same criteria of item 8.
- The cavity after the preparation for the repairs were over 20% of the width or
25 mm whichever is smaller;
10 – MACHINING
10.1 – The machining of the casting shall only be executed after solubilization heat
treatment.
10.2 – Because the superduplex steels have law machining, it becomes essential to
adopt some rules to avoid the getting new defects on the pieces. These rules
are:
- The machining equipment shall be robust, with enough power and free from
vibrations;
- The tool shall be kept sharp during all the machining process. Tools with a
not so sharp blade cause glazing and hardening of the surface of the steel.
APPENDIX 17
Minimum requirements for duplex and superduplex cast steel valve manufacturing
- The sharpening of the blade shall be made using an emery with a whole
uncontaminated grinder.
- Even for small advances the depth of the grinding shall be that so that it
would remove the layer below the deformed layer in the run before the last
avoiding hardening of the surface material;
- The angle of attack of the tool shall be so, that it avoids its friction on the
surface of the piece;
- The cutting tool shall be big enough to help with heat dissipation;
- The use of chip breaker shall be fit to direct the hard and long chips away
from the machining surface;
- The constant advance is extremely important to avoid that the tool friction
the piece;
- The use of adequate cooling fluid is essential, as well as the amount used.
This amount shall so, that it covers all cutting tool and the surface that is
being tooled/machined, allowing dispersal of the generated heat;
10.3 – After machining, a visual inspection and one by penetrant liquids shall be
made. The defects and indications shall be treated similarly to item 8.
10.5 – Repairs that require solubilization heat treatments shall take into
consideration the dimensional deformation. The heat treatment shall be
included as one of the three (03) authorized heat treatments when at foundry
and one (01) at machining shop, otherwise it shall be authorized by
PETROBRAS prior to execution.
APPENDIX 18
Technical data of organic coated for piping and valves.
This appendix defines technical data of organic coating for piping and valves. The
manufacturer of valves shall be agreement with the applicator for supply. When used in
systems piping with produced water (PCW).
1 - The preparation of the metallic surface prior to application of the coating should be
at least Sa 2 1/2 (to the near white metal) in accordance with the standard ISO 8501-1.
APPENDIX 18
Technical data of organic coated for piping and valves.
Abreviations:
A=Applicable
ID=Internal Diameter
L=Lenght
APPENDIX 18
Technical data of organic coated for piping and valves.
Thickness (µm)
Product name Final average
1ª cost 2ª cost 3ª cost
thickness
Belzona 1522 800 ---- ---- 800
5 - During the final inspection, first perform a visual check that there are no
discontinuities or projections along the entire surface of the organic coated, then
perform an inspection using a Holiday Detector with a 1,0 kV direct current. It’s not
admissible any kind of discontinuities/sparks on the metallic surface.
APPENDIX 19
Minimum requirements for non-metallic piping
1 - Introduction
1.3 – This appendix applies to pipe systems for transport of water and aqueous
solutions.
2 – Applicable Standards
IMO A 753 (18) - Guidelines for the application of plastic pipes on ships -
International Maritime Organization (resolution 18)
3 – General Specifications
3.1 – The non-metallic piping cited in item 1.2 of this appendix, used on floating
marine instalations of production, shall attend the requirements of resolution
IMO A 753 (18).
3.2 – The draftsman shall check the possibility of water hammer occurrence. If
positive, offer a revision of conducting the pipe to attenuate it, as well as, use
preferencially butterfly or gate valve.
3.3 - During project and assembly, the inspection of PETROBRAS shall check
the accomplishment to calculation of flexibility and supporting provided by the
draftsman.
3.4 – The overhead pipes, fittings and flanges in PRFV and RPVC shall have an
external layer of improved resin with ultraviolet inhibitor and also be painted
each 2 (two) years when exposed to ultraviolet light effects.
APPENDIX 19
Minimum requirements for non-metallic piping
3.5 – At new projects, pipes, fittings and flanges made on PRFV according
ASTM F1173 or on RPVC, shall be prepared by the same supplier. On cases of
extension or repair, shall be inspected the compatibility between the available
suppliers.
3.6 – The non-metallic piping shall have minimum internal roughness coefficient
of 140 Hazen-Williams.
3.7 - Pipes, fittings and flanges in PRFV and RPVC shall have wall thickness
calculated by supplier.
3.8 – The flanged fittings shall be made using a torquimeter, according values
and sequence of tightness provided by the supplier.
3.9 – Plain washers shall be used on flanged fittings, in order to allow a better
distribution of stress.
3.10 – During the assembly, the PETROBRAS inspection shall attest that the
alignement and paralellism tolerances attend the specifications of supplier.
3.14 – The lamination kit and the application procedure shall be purchased by
the same piping supplier.
4 - Constructive Characteristics
4.1 - PRFV
4.1.2 – Supplier shall own the Approval Certification of the Classifier Society to
the offered product.
4.1.3 - Pipes, fittings and flanges shall attend Appendix X3, paragraph X3.2.5.5
(electric conductivity) and appendix X4 (fatigue) from ASTM F 1173.
APPENDIX 19
Minimum requirements for non-metallic piping
4.1.4 - Pipes, fittings and flanges shall be united by buttweld with bandage.
4.2.1 - Pipes, fittings, flanges and valves shall not be exposed to ultraviolet light
effects.
4.2.3 – Supplier shall own the Approval Certification of the Classifier Society to
the offered product.
4.2.4 – Supplier shall provide necessary orientations and cares for welding.
4.3 - RPVC
4.3.1 – The junction of “liner” shall be made using weld with a PVC rod.
4.3.3 – During the process of junction, the disarrange between terminations shall
be corrected, in order to assure the continuity and integrity of the “liner”
(chemical fence).
5 - Inspection
For pipes, fittings and accessories made in PRFV, the visual inspection shall
attend criterias of ASTM F 1173.
6.1 – Non-metallic pipes, fittings and flanges shall be envolved with special care
for storing, handling and transporting, according supplier recommendations and
standards, in order to avoid damages, after the inspection of manufactoring.
APPENDIX 20
Industrial Valve Supply Requirements for E&P
ÍNDICE
1. Objective 2
2. Reference Documents 2
3. Definitons 2
4. General Requirements 2
7. Pos-Test Activities 9
8. Receiving Inspection 14
9. Storage 14
Define the requirements for receiving activities (inspection, tests, packaging, storage and
preservation) of industrial valves (VETs and conventional) in E&P, establishing minimum
requirements to be met throughout the supply cycle, either in cases of acquired valves by third
parties for use in new industrial units (typical EPCista cases) or in the case of acquired valves
by UNs for assembly and maintenance of existing facilities or new facilities.
2. REFERENCE DOCUMENTS
th
API Standard 6D – Valve Inspection and Testing, 22 Edition, January 2002
API Standard 598 – Valve Inspection and Testing, 8th Edition, May 2004
API Standard 609 – Butterfly Valves: Double Flanged, Lug- and Wafer-Type, 6th Edition, May
2004
ANSI B 16.34 – Valve – Flanged, Threaded, and Welding End
ET-3000.00-1200-956-PCI-001-Rev.0 - Código de Cores – Pintura (Especificação Técnica da
PETROBRAS)
MSS SP-25 – Standard Marking System for Valves, Fittings, Flanges and Unions, Jan 1998
3. DEFINITIONS
EPCista -Service provider, PETROBRAS’ supplier responsible for the EPC contract
(Engineering, Procurement and Construction)
Vendor List -List of qualified companies to supply equipment, materials and services.
4. GENERAL REQUIREMENTS
4.1.1. The Inspection and Testing Plan developed by the supplier shall allow the identification of
stages, throughout the valve production cycle, where it shall be done checks or inspections,
including those carried out by material or service suppliers.
Note: This document shall indicate the types of examinations, tests or checks to be made, as
well as procedures and/or applicable instructions, acceptance criteria and issued records.
4.2.1. Supplier shall have and present the procedures and instructions for inspection of all
expected activities in PIT.
4.2.2. The procedures shall present the acceptance criteria and reference standards or
specifications of which were based on, they shall also be submitted for review and comments
by the inspection responsible company and posterior approval by
PETROBRAS.
4.3.1. Qualified companies to provide services for the supervision, inspection and testing of
valves, cited in this Specification, shall be registered in the Vendor List of the project or supply
contract.
4.3.2. The final inspection shall be done on the manufacturer facilities, which shall be witnessed
and approved by a supervisor or professional (inspector), indicated or approved by
PETROBRAS, or Member Company to the Project "Vendor List", qualified by
PETROBRAS/E&P.
4.3.3. The final inspection shall include at least the following checks:
4.3.6. Verification, by sampling, the actuation torque and the grasp torque of the joint body and
cover screws/prisoners.
4.3.7. According to PETROBRAS and justification, it may be allowed, in exceptional cases, the
disassembly of a valve for internal parts verification.
NOTE: PETROBRAS, as the final receiver of the hired items, reserves the right at any time of
the contract, of verifying the applicability of the supplier Quality System.
-It shall not be allowed the use of tape or Teflon paste (except cast iron valves, bronze or
resilient sealing) as an auxiliary element to seal threads, metal x metal (ex: NPT).
Fully tight valves are classified by series or families as defined in Appendix 14 of this Technical
Specification (ex. SERIE -000 Ball valve, SERIE -100 Plug valve with expanding slips, etc.
Pressure Test, for fully tight valve tests, shall be obtained from Table "A" - Recommended
Pressure Test for Hydrostatic Testing of VETs, below:
TEST PRESSURE
VALVE WORKING
VALVE CLASS(#) SEALING
PRESSURE (PSI)
PSI Kgf/cm²
11
600 1480 1628
4
15
800 1973 2170
2
17
900 2220 2442
2
28
1500 3705 4075
6
47
2500 6170 6787
7
85
4500 11110 12221
9
NOTE: 1. Butterfly valves API 609, Category A, shall be tested according manufacturer
procedures.
2. Table based on recommended values by Standard ASME B16.34.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 5 of 14
APPENDIX 20
Connection Details for Pressure Instruments
5.2.2 Test Duration.
The test duration, for hydrostatic testing of fully tight valves, shall be obtained from Table B –
Indicated time for hydrostatic testing of VETs, below:
Obs.: Observing time shall start after the test pressure stabilization.
The criteria set here for the hydrostatic test of the body are applicable to all series or families of
VET's defined in Appendix 14 of this Technical Specification.
a. Before beginning the test, all surfaces of the valve shall be clean and dry.
b. The test fluid is filtered water, free from solids, at environmental temperature, with chloride
content of less than 30 PPM containing adequate inhibitor corrosion, to ensure the integrity of
the valve components. The fluid temperature of the test shall be between 5 °C and 50 °C (API
598, ITEM 3.6.1).
c. The test shall be executed by applying to the internals of the valve (body), a pressure equal
to 1.5 times the valve working pressure, according to Table "A", and duration according to
Table "B".
The valve shall be tested in the partially open position (45º), ensuring that it is completely filled
with the fluid test.
a. Inspect the valve carefully for any lack of tightness (visual), noting cracks, deformation or
other porosity.
b. The test will be considered approved if there is no pressure drop or drip during its execution.
The general conditions presented here for the hydrostatic testing of fully tight valves are
applicable to all series or families of VETs defined in Appendix 14 of this Technical
Specification.
a. The leak test is done by applying a pressure equal to 1.1 times the maximum valve working
pressure to the internal valve device, completely closed, according to values defined in Table
"A" and a duration time according to Table "B".
b. For valves equipped with automatic thermal relief device, it shall be confirmed it was properly
calibrated, certified and is permanently installed in the valve body. The “set” shall be 1.25 times
the valve working pressure found in the table "A" for their respective class.
c. All valves shall be painted and with all accessories mounted for the tightness test.
d. The inspector in charge shall ensure, through the display device of lack of tightness installed
(transparent tube or hose), that internal complex is completely filled with the fluid test.
e. All valves with castle shall be tested in the vertical position, ensuring that their body and
cover are completely filled with the test fluid.
f. By the hydrostatic test finishing, the set valve + actuator shall be operated a few times,
covering at least one cycle of opening and closing in each flow direction, under atmospheric
pressure. This procedure shall also be repeated under a maximum differential pressure
specified for the actuator.
Note: The dimensions of the actuator shall consider as a safety factor, a minimum torque to
actuate the valve under a pressure value increased by at least 20% of ∆P indicated in the Data
Sheet of the valve.
g. During the opening/closing operation of the valve, mentioned in the previous paragraph,
under maximum differential pressure, it shall be verified the actuator maneuverability and
coupling conditions, which shall not allow the rotary sliding of the actuator.
i. The measurement of the actuation torque shall be done during the tightness tests and it shall
include opening and closing torques under atmospheric pressure and maximum differential
pressure test.
j. It may be accepted the reduction of the tightness test pressure in the no preferential valve
direction, since this information is described in the manufacturer technical documentation.
The specific conditions presented here for the tightness hydrostatic test of fully tight valves are
particular to the different series or families of VETs defined in Appendix 14 of this Technical
Specification:
-The manufacturer shall submit for PETROBRAS approval the pressure test procedure, in
accordance to the project and valve construction standards, including specific requirements for
different models of VET defined in Appendix 14 of this Technical Specification.
-The series or families of VETs, described below, have specific characteristics which shall be
checked during the tightness hydrostatic tests:
a. For VETs Series 000-Ball Valve -Double block and floating seats, SELF RELIEF type, are
valid the following recommendations:
-The test shall be done in both flow directions and it shall be checked the tightness visually
through the valve cavity, which shall be open to the atmospheric pressure by the testing device
(transparent tube or hose) previously installed.
-The cavity relief test shall be done in both direction, with gradual pressure increasing, and be
recorded the cavity relief pressure, which shall not exceed 33% of valve working pressure.
b. For VET Series 000 -Ball valve with double block and floating seats, double piston effect;
VET Series 100-Plug valve with expanding slips, double block and fixed seats with automatic
thermal relief device, VET Series 500-Expanding Gate valve, double block with cavity relief
device installed, are valid the following recommendations:
-The test shall be done in both flow directions and it shall be checked the tightness visually
through the valve cavity, which shall be open to the atmospheric pressure by the testing device
(transparent tube or hose) previously installed.
-The tightness cavity test shall done with a hydrostatic test pressure as defined in Table “A” and
duration as defined in Table "B" used in the valve cavity, with endings opened to atmospheric
pressure.
5.5.2.1. Similarly to hydrostatic testing, the manufacturer shall submit to previous PETROBRAS
approval, the pneumatic testing procedure of low pressure, in accordance to the project and
valve construction standards, including specific requirements for different models of VET
defined in Appendix 14 of this Technical Specification.
5.5.2.2. For VET Series 000 -Ball Valve with double block and floating seats, double piston
effect; VET Series 100-Valve type male with expandable shoes, double block and fixed seats
with automatic thermal relief device VET Series 500-Expanding Gate Valve, double block with
cavity relief device installed, are valid the following recommendations
a. The test shall be done in both flow directions and it shall be checked the tightness visually
through the valve cavity, which shall be open to the atmospheric pressure by a
testing device meant for leaking detection.
b. The tightness cavity test shall be done with the test pressure, defined in Section 6.3, and
duration according to table "B", applied to the valve cavity, with endings opened to the
atmospheric pressure.
c. To carry out these tests the valve shall be completely dry and clean, internally and externally.
d. If necessary, to ease leak visualization, it can be used soapy solution or equivalent, which
enables the identification of bubbles.
6.1.1. The torque required to open the valve shall be measured on the valve stem during the
final tests at the factory, under maximum differential pressure, according to table A, as follows:
1. Open to close position, with the valve passage pressurized and with the body cavity under
atmospheric pressure.
2. Close to open position, with both sides of the valve pressurized and body cavity under
atmospheric pressure.
3. Close to open position, with one valve side (A) pressurized along with the body cavity and the
other side (B) opened to atmospheric pressure.
6.2.1. The torque required to open the valve shall be measured on the valve stem during the
final tests at the factory, under maximum differential pressure, according to table A, as follows:
1. Open to close position, with the valve passage pressurized and with the body cavity under
atmospheric pressure.
2. Close to open position, with both sides of the valve pressurized and body cavity opened to
atmospheric pressure.
3. Close to open position, with one valve side (A) pressurized along with the body cavity and the
other side (B) opened to atmospheric pressure.
4. Close to open position with one valve side (B) pressurized along with the body cavity and the
other side (A) opened to atmospheric pressure.
Note: The beginning, intermediate and resettlement torques shall be recorded where
applicable.
6.3.1. The relief test of the body cavity seat shall be done after the hydrostatic test and before
the functional tests.
6.3.3. It shall be increased the pressure in the body cavity, gradually, until the pressure is
released, the same shall be done until the second seat releases the pressure.
6.3.4. The results shall be recorded in reports or forms for valve documentation.
7. POST-TEST ACTIVITIES
7.1.1. When the painting process is part of the contract, the supplier shall present the valve
painting plan, according to PETROBRAS and approved by Painting Inspector Level II.
7.1.2. Painting Inspection Plan, as well as training records of the professionals involved in the
painting process shall be submitted to PETROBRAS before services begun.
7.1.5. The color definition applied to valves shall meet the ET-3000.00-1200-956-PCI001 (Color
Code – Painting, for UEPs).
7.2.1. The supplier shall have instruction which defines the systematic of identification, marking
and traceability of valves components mounted.
7.2.2. The supplier shall physically identify and track all critical components defined by the
project, for each product, through traceability lists of components and/or fabrication lot per
product.
7.2.3. Each valve shall be identified with an individual serial number, beyond the individual
identification of components defined as critical, enabling their effective traceability. The
identification component per lot is allowed only if this systematic allows tracking all critical
components per valve.
7.2.4. Valves and their components shall be identified according to manufacturing standard and
to the Standard MSS SP-25.
7.3.1. The supplier shall submit for analysis, comments and PETROBRAS approval a method
that defines the systematic of handling, preservation, packaging and shipping to all components
and equipment included in scope of supply (including actuators).
7.3.2. The packing of the valves shall be done according to PETROBRAS, to ensure that the
valves do not suffer damages during handling and transportation between the factory and the
facility.
7.3.3. The method shall include conservation conditions of seat components and endings
throughout the production, especially after the tightness tests, where it shall be checked the
cleaning and drying of the valves before packing.
7.3.4. This method shall also inform the antioxidant used for internal parts protection, as well as
unpainted external parts, such as screws, nuts and bezels. (Figure 1).
7.3.5. For valves made of brass, stainless steel and other metal alloys called "nonoxidizable",
the method shall indicate the protective against dust and moisture.
7.3.6. After the protective application, all valves shall have their cavities blocked by rubber
plates or plastic material, and glued outer surfaces of the flanges in order to keep out dust and
moisture.
7.5. Data-Book
Unless otherwise specified in the contract, Material Request or Technical Specification, the
national or foreign supplier shall elaborate the Valve "Data-Book", containing at least the
following items:
-Certificates of Compliance;
-Reports of Non-compliance and Corrective Actions taken, relevant to the delivered product;
-PIT Copy approved by Petrobras;
-Copy of all reports issued by the company responsible for inspection and approved by
PETROBRAS.
8.1. The receiving inspection shall be done without causing damages to the package and
without compromising the preservation of the valves.
8.2. It shall be carried out the documentation verification and its compliance with the product
plaque identification, serial number, valve pressure class, etc.).
8.2.1. This documentation shall also contain the Certificate of Material Releasing, at the factory,
duly signed by PETROBRAS representative and the Manufacturer's Manual containing handling
and preservation procedures.
8.2.2. After verifying the documentation and attesting its conformity, the packed valve shall be
sent to storage in a suitable location.
9. STORAGE
The storage location of the valves, as well as their preservation plan, shall be
inspected and approved by PETROBRAS representative.
10.1. VETs shall only be removed from storage location, after certifying that the lines where
they will be installed are thoroughly clean, by certificate of boroscope.
10.2. The valve packing shall only be removed at the time of installation.
10.3. The method for tightness visualization of in-line valves shall be through pressure drop in
the manometer used by the staff responsible for piping assembly, during the line tightness test.
10.3.1. If it is verified lack of tightness in a valve during line tests, it shall be withdrawn and re-
evaluated in certified bench, in the presence of manufacturer's technical and other parties
involved.
10.3.2. After line tightness test, where there are VETs installed, the responsible for preservation
shall ensure that they, along with the valves, are properly preserved in order to ensure non-
oxidation of the valves.
Valves Description
VAG-09 G14 Globe valve; stainless steel; union bonnet; needle disc;
inside screw stem; rising stem; screwed ends, ASME
B1.20.1 NPT; male-female; ASME B16.34 standard; ASME
B1.20.1 NPT; body-seat ASTM A 182 Gr F 316; needle AISI
316; max. pressure 5000 psi.
VAG-17 A8 B4 B9 Globe valve; carbon steel; union bonnet; needle disc; inside
B10 B15 screw stem; rising stem; socket weld ends MSS SP-84;
B17C4 C9 ASME B16.34 standard; body-seat ASTM A 105; needle
C10 E4 E9 ASTM A 564 type 630; max. pressure 3000 psi.
E10 E10R
E17 F4 F10
F10R
VAG-18 G4 G10 Globe valve; carbon steel; union bonnet; needle disc; inside
G10P G10R screw stem; rising stem; socket weld ends MSS SP-84;
G18 ASME B16.34 standard; body-seat ASTM A 105; needle A
564 type 630; max. pressure 5000 psi.
VAG-21 B6 B19 C6 Globe valve; carbon steel; union bonnet; needle disc; inside
E6 E6R F6 screw stem; rising stem; socket weld ends MSS SP-84;
F6R ASME B16.34 standard; body-seat ASTM A 350 Gr LF2 CL
1; needle A 564 type 630; max. pressure 3000 psi.
VAG-23 G6 G6R G19 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; socket weld ends MSS SP-84;
ASME B16.34 standard; body-seat ASTM A 350 Gr LF2 CL
1; needle A 564 type 630; max. pressure 5000 psi.
VAG-28 B12 C12 Globe valve; stainless steel superduplex; union bonnet;
needle disc; inside screw stem; rising stem; socket weld ends
MSS SP-84; ASME B16.34 standard; body-seat-needle
ASTM A 182 Gr F55 (UNS S32760); max. pressure 3000 psi.
VAG-29 B13 C13 Globe valve; stainless steel superduplex; union bonnet;
needle disc; inside screw stem; rising stem; socket weld ends
MSS SP-84; ASME B16.34 standard; body-seat-needle
ASTM A 182 Gr F53 (UNS S32750); max. pressure 3000 psi.
VAG-30 G12 G12P Globe valve; stainless steel superduplex; union bonnet;
needle disc; inside screw stem; rising stem; socket weld ends
MSS SP-84; ASME B16.34 standard; body-seat-needle
ASTM A 182 Gr F55 (UNS S32760); max. pressure 5000 psi.
VAG-31 B11 B14 B22 Globe valve; carbon steel; union bonnet; needle disc; inside
B23 B24 C11 screw stem; rising stem; screwed ends; ASME B1.20.1 NPT;
E11 F11 male-female; ASME B16.34 standard; body-seat ASTM A
105; needle ASTM A 564 type 630; body-needle organic
coated; max. pressure 3000 psi.
VAG-32 G11 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; screwed ends; ASME B1.20.1 NPT;
male-female; ASME B16.34 standard; body-seat ASTM A
105; needle A 564 type 630; body-needle organic coated;
max. pressure 5000 psi.
VAG-33 H11 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; screwed ends; ASME B1.20.1 NPT;
male-female; ASME B16.34 standard; body-seat ASTM A
105; needle A 564 type 630; body-needle organic coated;
max. pressure 6000 psi.
VAG-35 B16 C16 E16 Globe valve; stainless steel duplex; union bonnet; needle
F16 disc; inside screw stem; rising stem; socket weld ends MSS
SP-84; ASME B16.34 standard; body-seat-needle ASTM A
182 Gr F 51 (UNS S31803); max. pressure 3000 psi.
VAG-36 G16 G16P Globe valve; stainless steel duplex; union bonnet; needle
disc; inside screw stem; rising stem; socket weld ends MSS
SP-84; ASME B16.34 standard; body-seat-needle ASTM A
182 Gr F 51 (UNS S31803); max. pressure 5000 psi.
VAG-37 H14 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; buttweld ends, ASME B16.25;
ASME B16.34 standard; body-seat ASTM A 105; needle A
564 type 630; body-needle organic coated; max. pressure
6000 psi.
VAG-40 B30 C30 E30 Globe valve; union bonnet; needle disc; inside screw stem;
E32 F32 F33 rising stem; socket weld ends, ASME B16.25; ASME B16.34
standard; body-seat-needle ASTM B564 (UNS N06625);
max. pressure 3000 psi.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 3 of 94
VAG-41 H30 H30P Globe valve; ASTM B564 (UNS N06625); union bonnet;
H33 H38 needle disc; inside screw stem; rising stem; buttweld ends,
H38P ASME B16.25; ASME B16.34 standard; body-seat-needle
ASTM B564 (UNS N06625); max. pressure 5000 psi.
VAG-43 H10 H10P Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; buttweld ends ASME B16.25; ASME
B16.34 standard; body-seat ASTM A 105; needle A 564 type
630; max. pressure 6000 psi.
VAG-47 H6 Globe valve; carbon steel; union bonnet; needle disc; inside
screw stem; rising stem; buttweld ends ASME B16.25; ASME
B16.34 standard; body-seat ASTM A 350 Gr LF2 CL 1;
needle A 564 type 630; max. pressure 6000 psi.
VB-10 A4 B5 Butterfly valve; wafer; ductile iron; lateral gear operator; body
ASTM A 536 Gr 65-45-12; body-seat Buna N liner; disc AISI
316 solid stem AISI 316; API 609 category A standard; max.
pressure 250 psig.
VB-11 B7R B10 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body-disc ASTM A 536 Gr 65-45-12; body-
seat coated with Viton; disc coated with Nylon 11; solid stem
AISI 316; API 609 category A standard; raised face (RF);
max. pressure 150 psig.
VB-12 B7R B10 Butterfly valve; wafer; ductile iron; lateral gear operator;
body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; raised face (RF); max. pressure
150 psig.
VB-12A B7R B10 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65-45-12; body-seat
coated with Viton; disc coated with Nylon 11; solid stem AISI
316; API 609 category A standard; raised face (RF);class
150, ASME B16.47 Series A; max. pressure 150 psig.
VB-13A B14 B22 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65-45-12; body-seat
coated with Viton; disc coated with Nylon 11; solid stem AISI
316; API 609 category A standard; flat face (FF) class 150,
ASME B16.47 Series A; max. pressure 150 psig.
VB-14 B10 B15 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body ASTM A 536 Gr 65-45-12; disc AISI
316; Viton seat; solid stem AISI 316; API 609 category A
standard; max. pressure 150 psig.
VB-15 B10 B15 Butterfly valve; wafer; ductile iron; lateral gear operator; body
ASTM A 536 Gr 65-45-12; disc AISI 316; Viton seat; solid
stem AISI 316; API 609 category A standard; max. pressure
150 psig.
VB-15A B10 B15 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body ASTM A 536 Gr 65-45-12; disc AISI 316;
Viton seat; solid stem AISI 316; API 609 category A
standard; raised face (RF) class 150, ASME B16.47 Series
A; max. pressure 150 psig.
VB-16 B10 B15 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body ASTM A 536 Gr 65-45-12; disc AISI
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 5 of 94
316; Viton seat; solid stem AISI 316; API 609 category A
standard; max. pressure 250 psig.
VB-17 B10 B15 Butterfly valve; wafer; ductile iron; lateral gear operator; body
ASTM A 536 Gr 65-45-12; disc AISI 316; Viton seat; solid
stem AISI 316; API 609 category A standard; max. pressure
250 psig.
VB-17A B10 B15 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body ASTM A 536 Gr 65-45-12; disc AISI 316;
Viton seat; solid stem AISI 316; API 609 category A
standard; raised face (RF) class 150 ASME B16.47 Series A;
max. pressure 250 psig.
VB-18 B7 B7R B10 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body-disc ASTM A 536 Gr 65-45-12; body-
seat coated with Viton; disc coated with Nylon 11; solid stem
AISI 316; API 609 category A standard; Raised face (RF);
max. pressure 250 psig.
VB-19 B7 B7R B10 Butterfly valve; wafer; ductile iron; lateral gear operator;
B14 B22 B23 body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; Raised face (RF) ;max. pressure
250 psig.
VB-19A B7 B7R B10 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65-45-12; body-seat
coated with Viton; disc coated with Nylon 11; solid stem AISI
316; API 609 category A standard; raised face (RF) class
150, ASME B16.47 Series A; max. pressure 250 psig.
VB-20 B23 Butterfly valve; wafer; ductile iron; lateral gear operator;
body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; flat face (FF) class 150, ASME
B16.47 Series A; max. pressure 250 psig.
VB-20A B14 B22 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65-45-12; body-seat
coated with Viton; disc coated with Nylon 11; solid stem AISI
316; API 609 category A standard; flat face (FF) class 150,
ASME B16.47 Series A; max. pressure 250 psig.
VB-22 B25 Butterfly valve; wafer; ductile iron; lateral gear operator; body
ASTM A 536 Gr 65-45-12; disc ASTM A 351 CD4MCuN;
Hypalon seat; API 609 category A standard; Flat flace (FF);
max. pressure 250 psig.
VB-22A B25 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body ASTM A 536 Gr 65-45-12; disc ASTM A 351
CD4MCuN; Hypalon seat; API 609 category A standard; flat
face (FF) ASME B16.47 Series A; max. pressure 250 psig.
VB-23 B15 Butterfly valve; flanged type; carbon steel; wrench operator,
90 degress rotation; body ASTM A 216 Gr WCB; disc AISI
316; Viton seat; solid stem AISI 316; API 609 category A
standard; raised face (RF); max. pressure 250 psig.
VB-24 B15 Butterfly valve; flanged type; carbon steel; lateral gear
operator; body ASTM A 216 Gr WCB; disc AISI 316; Viton
seat; solid stem AISI 316; API 609 category A standard;
raised face (RF); max. pressure 250 psig.
VB-24A B15 Butterfly valve; flanged type; carbon steel; lateral gear
operator; body ASTM A 216 Gr WCB; disc AISI 316; Viton
seat; solid stem AISI 316; API 609 category A standard;
mounted between flange (RF) ASME B16.47 Series A; raised
face (RF); max. pressure 250 psig.
VB-25 B7R B15 Butterfly valve; wafer; Ni/Al/Br; wrench operator, 90 degress
rotation; body-disc-stem ASTM B148 UNS C95800; Viton
seat; API 609 category A standard; max. pressure 150 psig.
VB-26 B7R B15 Butterfly valve; wafer; Ni/Al/Br; lateral gear operator; body-
disc-stem ASTM B148 UNS C95800; Viton seat; API 609
category A standard; max. pressure 150 psig.
VB-26A B7R B15 Butterfly valve; flanged type; Ni/Al/Br; lateral gear operator;
body-disc-stem ASTM B148 UNS C95800; Viton seat; API
609 category A standard; raised face (RF) ASME B16.47
Series A; max. pressure 150 psig.
VB-29 B7R Butterfly valve; flanged type; carbon steel; lateral gear
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 7 of 94
VB-29A B7R Butterfly valve; flanged type; carbon steel; lateral gear
operator; body-disc ASTM A 216 Gr WCB; body-seat coated
with Viton; disc coated with Nylon 11; solid stem AISI 316;
API 609 category A standard; raised face (RF) class 150,
ASME B16.47 Series A standard; max. pressure 250 psig.
VB-33 B11 Butterfly valve; wafer; ductile iron; lateral gear operator;
body-disc ASTM A 536 Gr 65.45.12 with organic coating;
body-seat Hypalon® liner; API 609 category A standard;
max. pressure 150 psig.
VB-33A B11 Butterfly valve; flanged type; ductile iron; lateral gear
operator; body-disc ASTM A 536 Gr 65.45.12 with organic
coating; body-seat Hypalon® liner; API 609 category A
standard; raised face (RF); ASME B16.47 Séries A; max.
pressure 150 psig.
VB-35 B14 B22 B24 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body-disc ASTM A 536 Gr 65-45-12; body-
seat coated with Viton; disc coated with Nylon 11; solid stem
AISI 316; API 609 category A standard; flat face (FF); max.
pressure 250 psig.
VB-36 B14 B22 B23 Butterfly valve; wafer; ductile iron; lateral gear operator;
B24 body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; Flat face (FF);max. pressure 250
psig.
VB-37 B14 B20 B22 Butterfly valve; wafer; ductile iron; wrench operator, 90
degress rotation; body-disc ASTM A 536 Gr 65-45-12; body-
seat coated with Viton; disc coated with Nylon 11; solid stem
AISI 316; API 609 category A standard; flat face (FF); max.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 8 of 94
VB-38 B14 B22 Butterfly valve; wafer; ductile iron; lateral gear operator;
body-disc ASTM A 536 Gr 65-45-12; body-seat coated with
Viton; disc coated with Nylon 11; solid stem AISI 316; API
609 category A standard; flat face (FF); max. pressure 150
psig.
VE-01 C8 E8 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; screwed ends
ASME B1.20.1 NPT; body ASTM A 105; AISI 410 trim; soft
seat; ISO 17292 standard; class 800.
VE-04C B15 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
soft seat; ISO 17292 standard; class 800.
VE-05B F10R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
soft seat; ASME B16.34 LTD standard; class 1500.
VE-05C F10R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
soft seat; ASME B16.34 LTD standard; class 1500.
VE-08 C6 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; soft seat; ISO 14313 (API 6D) standard; class
300.
VE-09 C6 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 300.
VE-10 B15 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-10E A8 B14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 9 of 94
trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-11E C14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
trim; soft seat; ISO 14313 (API 6D) standard; class 300.
VE-13 E10R E14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 600.
VE-14 F10R F14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 900.
VE-15 F10R F14 Ball valve; full bore; carbon steel; bolted body; trunnion-
G10R G14 mounted; wrench (lever) operator, 90 degrees rotation;
G18 flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 1500.
VE-16 H10 H14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 2500.
VE-17 B15 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; soft seat; ISO 14313 (API 6D) standard; class
150.
VE-17E A8 B14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB; AISI
410 trim; soft seat; ISO 14313 (API 6D) standard; class 150.
VE-18E C14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB; AISI
410 trim; soft seat; ISO 14313 (API 6D) standard; class 300.
VE-20 E10R E14 Ball valve; full bore; carbon steel; bolted body; trunnion-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 10 of 94
VE-21 F10R F14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-22E A8 B14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; flat face (FF); body ASTM A 216
Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 150.
VE-22F B14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; flat face (FF); body
ASTM A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313
(API 6D) standard; class 150.
VE-23E C14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; flat face (FF); body ASTM A 216
Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 300.
VE-23F C14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; flat face (FF); body
ASTM A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313
(API 6D) standard; class 300.
VE-25 E10R E14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-26 F10R F14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-27 G10R G14 Ball valve; full bore; carbon steel; bolted body; trunnion-
G18 mounted; handwheel gear operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 11 of 94
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-28 H10 H14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 2500.
VE-43D G10R G18 Ball valve; full bore; carbon steel; bolted body; trunnion
assembly; wrench operator, 90 degrees rotation; socket weld
ends with nipple SCH 160; body ASTM A 105; ball AISI 410;
soft seat; ASME B16.34 LTD standard; class 1500.
VE-44 A8 B14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410
trim; soft seat; ISO 17292 standard; class 150.
VE-45 C14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105; AISI 410 trim;
soft seat; ISO 17292 standard; class 300.
VE-46 E14 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 105; AISI
410 trim; soft seat; ISO 17292 standard; class 600.
VE-47 F14 G14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; soft seat; ASME B16.34 LTD standard;
class 1500.
VE-48B B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
C10 wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
metal-metal; ISO 17292 standard; class 800.
VE-48C B10 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
metal-metal; ISO 17292 standard; class 800.
VE-48D B5 B9 C5 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
E5 wrench (lever) operator, 90 degrees rotation; socket weld ends
with nipple XXS; body ASTM A 105; AISI 410 trim; metal-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 12 of 94
VE-49D F5 G5 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple XXS; body ASTM A 105; AISI 410 trim;
metal-metal; ASME B16.34 LTD standard; class 1500.
VE-50 B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; metal-metal; ISO 14313 (API 6D) standard; class 150.
VE-51 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; metal-metal; ISO 14313 (API 6D) standard; class 300.
VE-67 B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-68 B9 B10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; metal-metal; ISO 14313 (API
6D) standard; class 150.
VE-68A B9 B10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; AISI 410 trim; metal-metal; ISO
14313 (API 6D) standard; class 150.
VE-69 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; metal-metal; ISO 14313 (API 6D) standard;
class 300.
VE-70 C9 C10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; metal-metal; ISO 14313 (API
6D) standard; class 300.
VE-74 B13 C13 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 40S; body-ball ASTM A 182
Gr F53 (UNS S32750); soft seat; ISO 17292 standard; class
800.
VE-76 B13 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-ball ASTM
A 995 Gr 5A (UNS J93404); soft seat; ISO 14313 (API 6D)
standard; class 150.
VE-77 B13 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
ball ASTM A 995 Gr 5A (UNS J93404); soft seat; ISO 14313
(API 6D) standard; class 150.
VE-78 C13 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-ball ASTM
A 995 Gr 5A (UNS J93404); soft seat; ISO 14313 (API 6D)
standard; class 300.
VE-79 C13 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
ball ASTM A 995 Gr 5A (UNS J93404); soft seat; ISO 14313
(API 6D) standard; class 300.
VE-83 C12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-ball ASTM
A 995 Gr 5A (UNS J93404); metal-metal; ISO 14313 (API
6D) standard; class 300.
VE-91B C6 E6 E6R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ISO 17292 standard; class 800.
VE-91C C6 E6 E6R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ISO 17292 standard; class 800.
VE-92 E6 E6R Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-93 E6 E6R Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 600.
VE-94B F6 F6R Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; soft seat; ASME B16.34 LTD standard; class
1500.
VE-94C F6 F6R Ball valve; full bore; carbon steel; bolted body; trennion
assembly; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 160; body ASTM A 350 Gr
LF2 CL1; AISI 304 trim; soft seat; ASME B16.34 LTD
standard; class 1500.
VE-94D G6 G6R G19 Ball valve; full bore; carbon steel; bolted body; trunnion
assembly; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple XXS; body ASTM A 350 Gr LF2
CL1; AISI 304 trim; soft seat; ASME B16.34 LTD standard;
class 1500.
VE-95 F6 F6R G6 Ball valve; full bore; carbon steel; bolted body; trunnion-
G6R G19 mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-96 F6 F6R Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 900.
VE-97 F6 F6R Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 15 of 94
VE-99 G6 G6R G19 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; soft seat; ISO 14313 (API 6D)
standard; class 1500.
VE-102B F10R Ball valve; fire tested; full bore; carbon steel; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 80; body ASTM A 105; AISI
410 trim; soft/metallic seat; ASME B16.34 / ISO 10497
standard; class 1500.
VE-102C F10R Ball valve; fire tested; full bore; carbon steel; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 160; body ASTM A 105;
AISI 410 trim; soft/metallic seat; ASME B16.34 / ISO 10497
standard; class 1500.
VE-102D G10P G10R Ball valve; fire tested; full bore; carbon steel; bolted body
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple XXS; body ASTM A 105; AISI
410 trim; soft/metallic seat; ASME B16.34 LTD standard /
ISO 10497; class 1500.
VE-107 F10R Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 900.
VE-108 F10R G10R Ball valve; fire tested; full bore; carbon steel; bolted body;
G18 trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 1500.
VE-108P G10P Ball valve; piggable; fire tested; full bore; carbon steel; bolted
body; trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 105; AISI 410 trim; soft/metallic seat; ISO
14313 (API 6D) standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-109 H10 Ball valve; fire tested; full bore; carbon steel; bolted body;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 16 of 94
VE-119 F10R Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 900.
VE-125 F10R Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 900.
VE-126 G10R G18 Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 1500.
VE-126P G10P Ball valve; piggable; fire tested; full bore; carbon steel; bolted
body; trunnion-mounted; handwheel gear operator, 90
degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 216 Gr WCB; AISI 410 trim;
soft/metallic seat; ISO 14313 (API 6D) standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-127 H10 Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 216 Gr WCB; AISI 410 trim; soft/metallic seat;
ISO 14313 (API 6D) standard; class 2500.
VE-148 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; metal-metal; ISO 14313 (API 6D) standard;
class 150.
VE-149 B3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; metal-metal; ISO 14313 (API
6D) standard; class 150.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 17 of 94
VE-158 B25 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench, 90 degrees rotation; flanged ends ASME B16.5; flat
face (FF); body-trim ASTM A 995 Gr 1B (CD4MCuN); PTFE®
reinforced with 25% of carbon seat; ISO 14313 (API 6D)
standard; class 150.
VE-159 B20 Ball valve; full bore; body PVC; wrench; socket weld ends;
trim PVC; PTFE seat; class 150; Sch 80.
VE-160 B21 Ball valve; full bore; body CPVC; wrench; socket weld ends;
trim CPVC; PTFE seat; class 150; Sch 80.
VE-168 G12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 40S; body-ball ASTM A
182 Gr F55 (UNS S32760); soft seat; ASME B16.34 LTD
standard; class 1500.
VE-169 G12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body-ball
ASTM A 995 Gr 5A (UNS J93404); soft seat; ISO 14313 (API
6D) standard; class 1500.
VE-170 G12 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body-ball ASTM A 995 Gr 5A (UNS J93404); soft seat; ISO
14313 (API 6D) standard; class 1500.
VE-171 G12 G12P Ball valve; fire tested; full bore; stainless steel superduplex;
bolted body; floating ball; wrench (lever) operator, 90 degrees
rotation; socket weld ends with nipple Sch 40S; body-ball
ASTM A 182 Gr F55 (UNS S32760); soft seat/ metallic;
ASME B16.34 LTD standard; class 1500.
VE-172 G12 Ball valve; fire tested; full bore; stainless steel superduplex;
bolted body; floating ball; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body-ball ASTM A 995 Gr 5A (UNS J93404); soft seat; ISO
14313 (API 6D) standard; class 1500.
VE-173 G12 Ball valve; fire tested; full bore; stainless steel superduplex;
bolted body; trunnion-mounted; handwheel gear operator, 90
degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body-ball ASTM A 995 Gr 5A (UNS J93404); soft seat;
ISO 14313 (API 6D) standard; class 1500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 18 of 94
VE-173P G12P Ball valve; piggable; fire tested; full bore; stainless steel
superduplex; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body-ball ASTM A 995 Gr 5A
(UNS J93404);soft seat; ISO 14313 (API 6D) standard; class
1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-186D F11 G11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator; 90 degrees rotation;
flanged ends, ring type joint (RTJ); body ASTM A 105; ASTM
A 182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PEEK® seat; ASME B16.34 LTD standard; class 1500.
VE-187 F11 G11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK® seat; ISO 14313 (API 6D) standard;
class 1500.
VE-188 G11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK® seat; ISO 14313 (API 6D)
standard; class 1500.
VE-189 F11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK® seat; ISO 14313 (API 6D) standard;
class 900.
VE-190 F11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK® seat; ISO 14313 (API 6D)
standard; class 900.
VE-191 F11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 19 of 94
VE-192 H11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 182 Gr F 51 (UNS 31803) trim; body-ball
organic coated; PEEK® seat; ASME B16.34 LTD standard;
class 2500.
VE-193 C11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; ASTM A
995 Gr 4A (UNS J92205) trim; body-ball organic coated;
PTFE® reinforced with 25% of carbon seat; ISO 14313 (API
6D) standard; class 300.
VE-194 H11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK® seat; ISO 14313 (API 6D) standard;
class 2500.
VE-195 C11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-ball organic
coated; PTFE® reinforced with 25% of carbon seat; ISO
14313 (API 6D) standard; class 300.
VE-196 H11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; lateral wrench operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim;
body-ball organic coated; PEEK® seat; ISO 14313 (API 6D)
standard; class 2500.
VE-197 C11 Ball valve; full bore; carbon steel, bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; body-
ball organic coated; PTFE® reinforced with 25% of carbon
seat; ISO 14313 (API 6D) standard; class 300.
VE-198 E11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 105; ASTM
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 20 of 94
VE-199 E11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 216 Gr
WCB; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PEEK® seat; ISO 14313 (API 6D) standard;
class 600.
VE-200 E11 Ball valve; full bore; carbon steel, bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, ring type joint (RTJ); body ASTM
A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; body-
ball organic coated; PEEK® seat; ISO 14313 (API 6D)
standard; class 600.
VE-201 C11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; ASTM A
182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PTFE® reinforced with 25% of carbon seat; ISO 17292
standard; class 300.
VE-202 E11 Ball valve; full bore; carbon steel, bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, ring type joint (RTJ); body ASTM A 105; ASTM
A 182 Gr F 51 (UNS 31803) trim; body-ball organic coated;
PEEK® seat; ISO 17292 standard; class 600.
VE-205 C11 Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
105; ASTM A 182 Gr F 51 (UNS 31803) trim; body-ball
organic coated; PTFE® reinforced with 25% of
carbon/metallic seat; ISO 17292 standard; class 300.
VE-206 C11 Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
105; ASTM A 995 Gr 4A (UNS J92205) trim; body-ball
organic coated; PTFE® reinforced with 25% of
carbon/metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-207 C11 Ball valve; fire tested; full bore; carbon steel, bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 21 of 94
VE-208 C11 Ball valve; fire tested; full bore; carbon steel, bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5, raised face (RF); body
ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205)
trim; body-ball organic coated; PTFE® reinforced with 25% of
carbon/metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-209 B16 C16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 40S; body-trim ASTM A
182 Gr F51 (UNS S31803); PTFE® reinforced with 25% of
carbon seat; ISO 17292 standard; class 800.
VE-210 B16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-211 B16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
trim ASTM A 995 Gr 4A (UNS J92205); PTFE® reinforced
with 25% of carbon seat seat; ISO 14313 (API 6D) standard;
class 150.
VE-211A B16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Séries A; raised face (RF); body-
trim ASTM A 995 Gr 4A (UNS J92205); PTFE® reinforced
with 25% of carbon seat; ISO 14313 (API 6D) standard; class
150.
VE-212 B16 C16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; body-trim ASTM A 182 Gr F51 (UNS S31803);
PTFE® reinforced with 25% of carbon / metallic seat; ISO
17292 standard; class 800.
VE-213 B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; floating ball; wrench (lever)
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 22 of 94
VE-214 B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-214A B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Séries A; raised face (RF); body-trim ASTM A 995 Gr 4A
(UNS J92205); PTFE® reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-216 C16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
VE-217 C16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
trim ASTM A 995 Gr 4A (UNS J92205); PTFE® reinforced
with 25% of carbon seat seat; ISO 14313 (API 6D) standard;
class 300.
VE-219 C16 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel duplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-220 C16 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel duplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body-trim ASTM A 995 Gr 4A
(UNS J92205); PTFE® reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 300.
VE-221 E16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 23 of 94
VE-222 E16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body-trim
ASTM A 995 Gr 4A (UNS J92205); Devlon® V seat; ISO
14313 (API 6D) standard; class 600.
VE-223 E16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body-trim ASTM A 995 Gr 4A (UNS J92205); Devlon® V seat;
ISO 14313 (API 6D) standard; class 600.
VE-224 E16 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel duplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; socket weld ends with
nipple Sch 40S; body-trim ASTM A 182 Gr F51 (UNS
S31803); Devlon® V / metallic seat; ISO 17292 standard;
class 800.
VE-225 E16 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel duplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body-trim ASTM A 995 Gr 4A
(UNS J92205); Devlon® V / metallic seat; ISO 14313 (API
6D) standard; class 600.
VE-226 E16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5; ring
type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205);
Devlon® V / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-227 F16 G16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; socket weld ends with nipple Sch 40S; body-trim
ASTM A 182 Gr F51 (UNS S31803); PEEK® seat; ASME
B16.34 LTD standard; class 1500.
VE-228 F16 G16 Ball valve; full bore; duplex steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, Ring type joint (RTJ); body-trim
ASTM A 995 Gr 4A (UNS J92205); PEEK® seat; ISO 14313
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 24 of 94
VE-229 G16 Ball valve; full bore; duplex steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, Ring type joint (RTJ); body-trim
ASTM A 995 Gr 4A (UNS J92205); PEEK® seat; ISO 14313
(API 6D) standard; class 1500.
VE-230 B3 C3 E3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316 trim; RPTFE® seat; ISO 14313 (API 6D) standard; class
800.
VE-231 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316 trim; metal-metal; ISO 14313 (API 6D) standard; class
800.
VE-232 G16 Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5 ring
type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205);
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
1500.
VE-232P G16P Ball valve; piggable; fire tested ISO 10497 (API 607); full
bore; duplex steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5 ring type joint (RTJ); body-trim ASTM A 995 Gr 4A
(UNS J92205); PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 1500.
Note: Internal diameter (ID) valve shall be define for Project
Engineer.
VE-234 E16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body-trim
ASTM A 995 Gr 4A (UNS J92205); TFE/P® seat; ISO 14313
(API 6D) standard; class 600.
VE-235 E16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body-trim ASTM A 995 Gr 4A (UNS J92205); TFE/P® seat;
ISO 14313 (API 6D) standard; class 600.
VE-237 F3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple SCH 40S; body ASTM A 182 Gr F
316L; AISI 316 trim; PEEK® seat; ASME B16.34 LTD
standard; class 1500.
VE-237B F3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple SCH 80S; body ASTM A 182 Gr F
316L; AISI 316 trim; PEEK®seat; ASME B16.34 LTD
standard; class 1500.
VE-238B G3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 80S; body ASTM A 182 Gr F 316L;
AISI 316 trim; PEEK® seat; ASME B16.34 LTD standard;
class 1500.
VE-240 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316 trim; PEEK® seat; ISO 14313 (API 6D) standard; class
800.
VE-241 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 150.
VE-242 B3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 150.
VE-243 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316 trim; TFE/P seat; ISO 14313 (API 6D) standard; class
800.
VE-244 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; TFE/P® seat; ISO 14313 (API 6D) standard;
class 150.
VE-245 B3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; TFE/P® seat; ISO 14313 (API
6D) standard; class 150.
VE-246 B3 C3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316 trim; RPTFE seat; ISO
14313 (API 6D) standard; class 800.
VE-247 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-248 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
PTFE® reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-249 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-250 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; PEEK® /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-251 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-255 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 27 of 94
VE-256 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 351 Gr CF8M; AISI 316 trim; TFE/P® /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-257 B3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 351 Gr CF8M; AISI 316 trim;
TFE/P® / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-259 C3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5, raised face
(RF); body ASTM A 351 CF8M; AISI 316 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 300.
VE-260 C3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5,
raised face (RF); body ASTM A 351 CF8M; AISI 316 trim;
PTFE® reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 300.
VE-261 E3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 40S; body ASTM A 182 Gr F 316L; AISI
316 trim; PEEK® seat; ISO 17292 standard; class 800.
VE-262 E3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 600.
VE-263 E3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 600.
VE-264 E3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316 trim; Devlon® V / metallic
seat; ISO 17292 standard; class 800.
VE-265 E3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; Devlon® V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-266 E3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; Devlon® V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-267 E3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 40S; body
ASTM A 182 Gr F 316L; AISI 316 trim; Devlon® V seat; ISO
17292 standard; class 800.
VE-268 E3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-269 E3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 351 Gr CF8M;
AISI 316 trim; PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-270 F3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends with nipple Sch 40S; body ASTM A 182 Gr F 316L;
AISI 316 trim; PEEK® seat; ASME B16.34 LTD standard;
class 1500.
VE-270B F3 Ball valve; full bore; stainless steel; bolted body; trunnion
mounted; wrench (lever) operator, 90 degrees rotation; socket
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 29 of 94
weld ends with nipple Sch 80S; body ASTM A 182 Gr F 316L;
AISI 316 trim; PEEK® seat; ASME B16.34 LTD standard;
class 1500.
VE-272 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 1500.
VE-273 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 900.
VE-274 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 900.
VE-275 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 40S;
body ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® /
metallic seat; ASME B16.34 LTD standard; class 1500.
VE-275B F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 80S;
body ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® /
metallic seat; ASME B16.34 LTD standard; class 1500.
VE-277 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; Devlon® V
/ metallic seat; ISO 14313 (API 6D) standard; class 900.
VE-278 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; Devlon® V
/ metallic seat; ISO 14313 (API 6D) standard; class 900.
VE-279 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 30 of 94
VE-280 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 40S;
body ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® /
metallic seat; ASME B16.34 LTD standard; class 1500.
VE-280B F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; socket weld ends with nipple Sch 80S;
body ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® /
metallic seat; ASME B16.34 LTD standard; class 1500.
VE-282 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim; PEEK® /
metallic seat; ISO 14313 (API 6D) standard; class 900.
VE-283 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
900.
VE-284 F3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-285B G3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 80S; body ASTM A 182 Gr 316L; AISI 316 trim; PEEK® /
metallic seat; ASME B16.34 LTD standard; class 1500.
VE-287 G3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316 trim;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 31 of 94
VE-288 G3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
stell; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 351 Gr CF8M; AISI 316
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 1500.
VE-294 E16 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel duplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body-trim ASTM A 995 Gr 4A
(UNS J92205); TFE/P® / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-295 E16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5; ring
type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205);
TFE/P® / metallic seat; ISO 14313 (API 6D) standard; class
600.
VE-296B B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 800.
VE-296C B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 800.
VE-297 B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 150.
VE-298 B6 B19 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 150.
VE-298A B6 B19 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; PEEK® seat; ISO 14313
(API 6D) standard; class 150.
VE-299B B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PTFE® reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 800.
VE-299C B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PTFE® reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 800.
VE-300 B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 352 Gr LCB; AISI 304 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-301 B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 352 Gr LCB; AISI 304 trim;
PTFE® reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-301A B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 352 Gr LCB; AISI
304 trim; PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-302B B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PEEK® / metallic
seat; ISO 14313 (API 6D) standard; class 800.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 33 of 94
VE-302C B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 350 Gr LF2 CL 1; AISI 304 trim; PEEK® / metallic
seat; ISO 14313 (API 6D) standard; class 800.
VE-303 B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 352 Gr LCB; AISI 304 trim; PEEK® /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-304 B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 352 Gr LCB; AISI 304 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-304A B6 B19 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 352 Gr LCB; AISI
304 trim; PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-305B B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK® seat; ISO 17292 standard; class 800.
VE-305D B9 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple XXS; body ASTM A 105; AISI 410 trim;
PEEK® seat; ISO 17292 standard; class 800.
VE-306 B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PEEK® seat; ISO 14313 (API 6D) standard; class 150.
VE-307 B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 150.
VE-308 B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK® seat; ISO 14313 (API 6D) standard;
class 150.
VE-308A B9 B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.47 Series A; raised face (RF); body ASTM A 216
Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 150.
VE-309B B9 B10 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
C10 steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ISO
17292 standard; class 800.
VE-309D B9 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ISO
17292 standard; class 800.
VE-310 B9 B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5 raised face (RF);
body ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-311 B9 B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5 raised face (RF);
body ASTM A 216 Gr WCB; AISI 410 trim; PEEK® / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-312 B9 B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PEEK® / metallic seat; ISO 17292 standard; class 150.
VE-312A B9 B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 216 Gr WCB; AISI
410 trim; PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-313C B10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK® seat; ISO 17292 standard; class 800.
VE-314 C3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 351 CF8M;
AISI 316 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 300.
VE-315 C3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
351 CF8M; AISI 316 trim; PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
VE-316 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 105; AISI 410
trim; PTFE® reinforced with 25% of carbon seat; ISO 14313
(API 6D) standard; class 300.
VE-317C B10 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ISO
17292 standard; class 800.
VE-318 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5, raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 300.
VE-319 C9 C10 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5, raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 300.
VE-321C C10 E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK® seat; ISO 17292 standard; class 800.
VE-325C C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 36 of 94
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PTFE® reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-328 B3 Ball valve; full bore; stainless steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 351 Gr CF8M;
AISI 316 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-329 B3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
351 Gr CF8M; AISI 316 trim; PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-330B B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 800.
VE-330C B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 350 Gr LF2 CL 1;
AISI 304 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 800.
VE-331 B6 B19 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 352 Gr LCB;
AISI 304 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-332 B6 B19 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
352 Gr LCB; AISI 304 trim; PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-332A B6 B19 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 352 Gr LCB; AISI 304 trim; PTFE® reinforced with
25% of carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-333B B9 B10 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
C10 wrench (lever) operator, 90 degrees rotation; socket weld
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 37 of 94
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PTFE® reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-333D B9 B17 C9 Ball valve; full bore; carbon steel; bolted body; floating ball;
E17 wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple XXS; body ASTM A 105; AISI 410 trim;
PTFE® reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-334 B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PTFE® reinforced with 25% of carbon seat; ISO 14313
(API 6D) standard; class 150.
VE-335 B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PTFE® reinforced with 25% of carbon seat;
ISO 14313 (API 6D) standard; class 150.
VE-336 B9 B10 B17 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-336A B9 B10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; AISI 410 trim; PTFE® reinforced with
25% of carbon seat; ISO 14313 (API 6D) standard; class
150.
VE-337B B9 B10 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
C10 steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PTFE® reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-337D B9 B17 C9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
E17 steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple XXS; body
ASTM A 105; AISI 410 trim; PTFE® reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-338 B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 38 of 94
VE-339 B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-340 B9 B10 B17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PTFE® reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 150.
VE-340A B9 B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator; flanged ends ASME B16.47 Series A; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-341C B10 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PTFE® reinforced with 25% of carbon seat; ISO 17292
standard; class 800.
VE-342C B10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PTFE® reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 800.
VE-343 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; AISI 410
trim; PEEK® seat; ISO 14313 (API 6D) standard; class 300.
VE-344 C9 C10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
AISI 410 trim; PEEK® seat; ISO 14313 (API 6D) standard;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 39 of 94
class 300.
VE-346B B11 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; ASTM A
182 Gr F 51 (UNS 31803) trim; body-trim organic coating;
PTFE® reinforced with 25% of carbon seat; ISO 17292
standard; class 150.
VE-347 B11 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 105; ASTM A
995 Gr 4A (UNS J92205) trim; body-trim organic coating;
PTFE® reinforced with 25% of carbon seat; ISO 14313 (API
6D) standard; class 150.
VE-348 B11 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-trim organic
coating; PTFE® reinforced with 25% of carbon seat; ISO
14313 (API 6D) standard; class 150.
VE-349 B11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205) trim; body-
trim organic coating; PTFE® reinforced with 25% of carbon
seat; ISO 14313 (API 6D) standard; class 150.
VE-349A B11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body
ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS J92205)
trim; body-trim organic coating; PTFE® reinforced with 25%
of carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-350B B11 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face (RF);
body ASTM A 105; ASTM A 182 Gr F 51 (UNS 31803) trim;
body-trim organic coating; PTFE® reinforced with 25% of
carbon / metallic seat; ISO 17292 standard; class 150.
VE-351 B11 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 40 of 94
VE-352 B11 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS
J92205) trim; body-trim organic coating; PTFE® reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-353 B11 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; ASTM A 995
Gr 4A (UNS J92205) trim; body-trim organic coating; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 150.
VE-353A B11 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body ASTM A 216 Gr WCB;
ASTM A 995 Gr 4A (UNS J92205) trim; body-trim organic
coating; PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-354 B12 C12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 40S; body-trim ASTM A
182 Gr F55 (UNS S32760); PTFE® reinforced with 25% of
carbon seat; ISO 17292 standard; class 800.
VE-355 B12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-trim ASTM
A 995 Gr 5A (UNS J93404); PTFE® reinforced with 25% of
carbon seat; ISO 14313 (API 6D) standard; class 150.
VE-356 B12 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 41 of 94
VE-356A B12 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.47 Series A; raised face
(RF); body-trim ASTM A 995 Gr 5A (UNS J93404); PTFE®
reinforced with 25% of carbon seat; ISO 14313 (API 6D)
standard; class 150.
VE-357 C9 C10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 300.
VE-358 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PTFE® reinforced
with 25% of carbon / metallic seat; ISO 14313 (API 6D)
standard; class 300.
VE-359 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; AISI 410 trim; PTFE®
reinforced with 25% of carbon / metallic seat; ISO 14313 (API
6D) standard; class 300.
VE-360 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PTFE® reinforced with 25% of carbon / metallic seat; ISO
14313 (API 6D) standard; class 300.
VE-361 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; AISI 410 trim; PEEK® / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-362 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; raised face
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 42 of 94
VE-363 C9 C10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body ASTM A 216 Gr WCB; AISI 410 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
300.
VE-364 B12 C12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; socket weld ends with
nipple Sch 40S; body-trim ASTM A 182 Gr F55 (UNS
S32760); PTFE® reinforced with 25% of carbon / metallic
seat; ISO 17292 standard; class 800.
VE-365 B12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A (UNS
J93404); PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 150.
VE-366 B12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A
(UNS J93404); PTFE® reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 150.
VE-366A B12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.47 Series A; raised face (RF); body-trim ASTM A
995 Gr 5A (UNS J93404); PTFE® reinforced with 25% of
carbon / metallic seat; ISO 14313 (API 6D) standard; class
150.
VE-367 C12 Ball valve; full bore; stainless steel superduplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.47 Series A; raised face (RF); body-
trim ASTM A 995 Gr 5A (UNS J93404); PTFE® reinforced
with 25% of carbon seat; ISO 14313 (API 6D) standard; class
300.
VE-368 C12 Ball valve; full bore; stainless steel superduplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.47 Series A; raised face
(RF); body-trim ASTM A 995 Gr 5A (UNS J93404); PTFE®
reinforced with 25% of carbon seat; ISO 14313 (API 6D)
standard; class 300.
VE-369 C12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; floating ball; wrench
(lever) operator, 90 degrees rotation; flanged ends ASME
B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A (UNS
J93404); PTFE® reinforced with 25% of carbon / metallic
seat; ISO 14313 (API 6D) standard; class 300.
VE-370 C12 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel superduplex; bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; flanged ends
ASME B16.5; raised face (RF); body-trim ASTM A 995 Gr 5A
(UNS J93404); PTFE® reinforced with 25% of carbon /
metallic seat; ISO 14313 (API 6D) standard; class 300.
VE-371 E3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 600.
VE-372 E3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 600.
VE-373D E9 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple XXS; body ASTM A 105; AISI 410 trim;
Devlon® V seat; ISO 17292 standard; class 800.
VE-374 E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; Devlon® V seat; ISO 14313 (API 6D)
standard; class 600.
VE-375 E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon® V seat; ISO 14313
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 44 of 94
VE-376 E9 E10 E17 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 600.
VE-377D E9 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple XXS; body
ASTM A 105; AISI 410 trim; Devlon® V / metallic seat; ISO
17292 standard; class 800.
VE-378 E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon® V / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-379 E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon® V / metallic seat; ISO 14313 (API 6D)
standard; class 600.
VE-380 E9 E10 E17 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon® V metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-381B E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
Devlon® V seat; ISO 17292 standard; class 800.
VE-381C E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 160; body ASTM A 105; AISI 410 trim;
Devlon® V seat; ISO 17292 standard; class 800.
VE-382B E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 45 of 94
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK® seat; ISO 17292 standard; class 800.
VE-383 E10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 600.
VE-384 E10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 600.
VE-385 E10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 600.
VE-387 B16 E16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
socket weld ends with nipple Sch 40S; body-trim ASTM A
182 Gr F51 (UNS S31803); TFE/P seat; ISO 17292 standard;
class 800.
VE-388 B16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body-trim ASTM
A 995 Gr 4A (UNS J92205); TFE/P seat; ISO 14313 (API 6D)
standard; class 150.
VE-389 B16 Ball valve; full bore; stainless steel duplex; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; raised face (RF); body-
trim ASTM A 995 Gr 4A (UNS J92205); TFE/P seat seat; ISO
14313 (API 6D) standard; class 150.
VE-389A B16 Ball valve; full bore; stainless steel duplex; bolted body;
floating ball; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.47 Séries A; raised face (RF); body-
trim ASTM A 995 Gr 4A (UNS J92205); TFE/P seat; ISO
14313 (API 6D) standard; class 150.
VE-390 B16 E16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 46 of 94
VE-391 B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; floating ball; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 150.
VE-392 B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
raised face (RF); body-trim ASTM A 995 Gr 4A (UNS
J92205); TFE/P / metallic seat; ISO 14313 (API 6D) standard;
class 150.
VE-392A B16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel duplex; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.47
Series A; raised face (RF); body-ball ASTM A 995 Gr 4A
(UNS J92205); TFE/P / metallic seat; ISO 14313 (API 6D)
standard; class 150.
VE-393B E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; Devlon® V / metallic seat; ISO 17292 standard;
class 800.
VE-393C E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; Devlon® V / metallic seat; ISO 17292 standard;
class 800.
VE-394 G10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5,
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK / metallic seat; ISO 17292 standard; class 1500.
VE-397B E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 80; body
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 47 of 94
VE-397C E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ISO
17292 standard; class 800.
VE-398 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
600.
VE-399 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-400 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-401B E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 80; body ASTM A 105; AISI 410 trim;
TFE/P® seat; ISO 17292 standard; class 800.
VE-401C E10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with niple Sch 160; body ASTM A 105; AISI 410 trim;
TFE/P® / metallic seat; ISO 17292 standard; class 800.
VE-402 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
TFE/P® seat; ISO 14313 (API 6D) standard; class 600.
VE-403 E10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 48 of 94
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; TFE/P® seat; ISO 14313 (API
6D) standard; class 600.
VE-404 E10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; TFE/P seat; ISO 14313 (API
6D) standard; class 600.
VE-405B E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 80; body
ASTM A 105; AISI 410 trim; TFE/P® / metallic seat; ISO
17292 standard; class 800.
VE-405C E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with niple Sch 160; body
ASTM A 105; AISI 410 trim; TFE/P® / metallic seat; ISO
17292 standard; class 800.
VE-406 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
TFE/P® / metallic seat; ISO 14313 (API 6D) standard; class
600.
VE-407 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; TFE/P® / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-408 E10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; TFE/P® / metallic seat; ISO 14313 (API 6D) standard;
class 600.
VE-409 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 1500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 49 of 94
VE-410 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 900.
VE-411 F3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 900.
VE-412D G19 Ball valve; fire tested; full bore; carbon steel; bolted body;
trennion assembly; wrench (lever) operator, 90 degrees
rotation; socket weld ends with nipple XXS; body ASTM A
350 Gr LF2 CL1; AISI 304 trim; soft/metallic seat; ASME
B16.34 / ISO 10497 standard; class 1500.
VE-413 G19 Ball valve; fire tested, full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LCB; AISI 304 trim; soft/metallic; ISO
14313 (API 6D) / ISO 10497 standard; class 1500.
VE-414 G19 Ball valve; fire tested, full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LCB; AISI 304 trim; soft/metallic; ISO
14313 (API 6D) / ISO 10497 standard; class 1500.
VE-415B F10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
Devlon® V seat; ASME B16.34 LTD standard; class 1500.
VE-415C F10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
Devlon® V seat; ASME B16.34 LTD standard; class 1500.
VE-416 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; Devlon® V seat; ISO 14313 (API 6D)
standard; class 1500.
VE-417 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 50 of 94
VE-418 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 900.
VE-419 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; Devlon® V seat; ISO 14313
(API 6D) standard; class 900.
VE-420B F10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 80; body ASTM A 105; AISI 410 trim;
PEEK® seat; ASME B16.34 LTD standard; class 1500.
VE-420C F10 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; socket weld
ends with nipple Sch 160; body ASTM A 105; AISI 410 trim;
PEEK® seat; ASME B16.34 LTD standard; class 1500.
VE-421 F10 G10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 1500.
VE-422 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 105; AISI 410 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 900.
VE-423 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 900.
VE-424 F10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 51 of 94
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 900.
VE-425B F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; Devlon® V / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-425C F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; Devlon® V / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-426 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon® V / metallic seat; ISO 14313 (API 6D) standard;
class 1500.
VE-427 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
Devlon® V / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-428 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon® V / metallic seat; ISO 14313 (API 6D)
standard; class 900.
VE-429 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; Devlon® V / metallic seat; ISO 14313 (API 6D)
standard; class 900.
VE-430B F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 80; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ASME
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 52 of 94
VE-430C F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; floating ball; wrench (lever) operator, 90
degrees rotation; socket weld ends with nipple Sch 160; body
ASTM A 105; AISI 410 trim; PEEK® / metallic seat; ASME
B16.34 LTD standard; class 1500.
VE-431 F10 G10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
1500.
VE-432 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 105; AISI 410 trim;
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
900.
VE-433 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-434 F10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 216 Gr WCB; AISI 410
trim; PEEK® / metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-435 G3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F 316L; AISI 316 trim; PEEK® seat; ISO 14313
(API 6D) standard; class 1500.
VE-436 G3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F 316L; AISI 316 trim; PEEK® seat; ISO 14313
(API 6D) standard; class 1500.
VE-437D G10 Ball valve; full bore; carbon steel; bolted body; trunnion-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 53 of 94
VE-438 G10 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB; AISI 410 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 1500.
VE-439D G10 Ball valve; fire tested ISO 10497 (API 607); full bore; carbon
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
XXS; body ASTM A 105; AISI 410 trim; PEEK® / metallic
seat; ASME B16.34 LTD standard; class 1500.
VE-440 F16 G16 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
G16P steel duplex; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; socket weld ends with nipple
Sch 40S; Ring type joint (RTJ); body-trim ASTM A 182 Gr
F51 (UNS S31803); PEEK® / metallic seat; ISO 17292
standard; class 1500.
VE-441 F16 G16 Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; wrench (lever) operator,
90 degrees rotation; flanged ends ASME B16.5, ring type joint
(RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205); PEEK® /
metallic seat; ISO 14313 (API 6D) standard; class 1500.
VE-446 H10 Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator 90 degrees
rotation; buttweld ends ASME B16.5; body ASTM A 105; AISI
410 trim; RPTFE®/Metal seat; class 2500.
VE-450 H14 Ball valve; fire tested; full bore; ASTM B564 (UNS N06625);
bolted body; trunnion-mounted; wrench (lever) operator, 90
degrees rotation; flanged ends ASME B16.5; ring type joint
(RTJ); body ASTM A105; AISI 410 trim; PEEK®/metal seat;
ISO 17292 standard; class 2500.
VE-451 H30 H38 Ball valve; fire tested; full bore; carbon steel with
Inconel®625; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A105 with coated ASTM
B564 (UNS N06625); AISI 410 trim; metal-metal; ISO 14313
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 54 of 94
VE-452 H30 H38 Ball valve; fire tested; full bore; carbon steel with
Inconel®625; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A216 Gr WCB with
coated ASTM B564 (UNS N06625); AISI 410 trim; metal-
metal; ISO 14313 (API 6D) standard; class 2500.
VE-452P H30P H38P Ball valve; piggable; fire tested; full bore; carbon steel with
ASTM B564 (UNS N06625); bolted body; trunnion-mounted;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A216 Gr
WCB with coated ASTM B564 (UNS N06625); AISI 410 trim;
metal-metal; ISO 14313 (API 6D) standard; class 2500. Note:
Internal diameter (ID) valve shall be defined for Project
Engineer.
VE-458 H10 H30 Ball valve; full bore; carbon steel; bolted body; trunnion-
H30P mounted; wrench (lever) operator, 90 degrees rotation;
buttweld ends ASME B16.5; ring type joint (RTJ); body
ASTM A 105; AISI 410 trim; PEEK® seat; ASME B16.34
standard; class 2500.
VE-460 E30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 WCB with ASTM B564 (UNS N06625); AISI 410 trim;
RPTFE®/Metal seat; ISO 14313 (API 6D) standard; class
600.
VE-461 E30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 WCB with ASTM B564 (UNS N06625); ISO 14313 (API
6D) standard; AISI 410 trim; RPTFE®/Metal seat; class 600.
VE-462 E30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring joint face (RTJ); body ASTM
A 216 WCB with ASTM B564 (UNS N06625); ISO 14313 (API
6D) standard; AISI 410 trim; RPTFE®/Metal seat; class 600.
VE-463 B30 C30 Ball valve; fire tested; full bore; bolted body; trunnion-
E30 E32 mounted; wrench (lever) operator, 90 degrees rotation; socket
weld ends ASME B16.5; body ASTM B 564 (UNS N06625);
AISI 410 trim; RPTFE®/Metal seat; ISO 17292 standard;
class 800.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 55 of 94
VE-463C H3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
buttweld ends ASME B16.25 with nipple SCH 160; body
ASTM A 182 Gr F 316L; AISI 316 trim; PEEK® seat; ISO
17292 standard; class 2500.
VE-463D H3 Ball valve; full bore; stainless steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 182 Gr F 316L; AISI 316 trim; PEEK® seat; ISO 17292
standard; class 2500.
VE-464 C30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB with ASTM B564 (UNS N06625); ISO 14313
(API 6D) standard; AISI 410 trim; RPTFE®/metal seat; class
300.
VE-465 C30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB with ASTM B564 (UNS N06625); ISO 14343
(API 6D) standard; AISI 410 trim; RPTFE®/Metal seat; class
300.
VE-466 C30 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; raised face (RF); body ASTM A
216 Gr WCB with ASTM B564 (UNS N06625); ISO 14343
(API 6D) standard; AISI 410 trim; RPTFE®/Metal seat; class
300.
VE-467 H30 H38 Ball valve; fire tested; full bore; carbon steel with ASTM
B564 (UNS N06625); bolted body; trunnion-mounted;
handwheel gear operator, 90 degrees rotation; compact
flanged NORSOK L-005; metallic seal joint (MSJ); body
ASTM A216 Gr WCB with coated ASTM B564 (UNS
N06625); AISI 410 trim; PEEK®/metal seat; ASME B16.34
standard; class 2500.
VE-467P H30P H38P Ball valve; piggable; fire tested; full bore; carbon steel with
Inconel®625; bolted body; trunnion-mounted; handwheel
gear operator, 90 degrees rotation; compact flanged
NORSOK L-005; metallic seal joint (MSJ); body ASTM A216
Gr WCB with coated ASTM B564 (UNS N06625); AISI 410
trim; PEEK®/metal seat; ASME B16.34 standard; class 2500.
Note: Internal diameter (ID) valve shall be defined for Project
Engineer.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 56 of 94
VE-468 H3 Ball valve; fire tested ISO 10497 (API 607); full bore; stainless
steel; bolted body; trunnion-mounted; handwheel gear
operator; 90 degrees rotation; flanged ends ASME B16.5;
ring type joint (RTJ); body ASTM A 182 Gr F 316L; AISI 316
trim; PEEK® mettalic/seat; ISO 14313 (API 6D) standard;
class 2500.
VE-471 B22 B20 B23 Ball valve monoblock; full bore, glass-fiber reinforced vinyl
ester, floating ball, wrench (lever) operator, quarter turn 90º,
flanged ends ASME B16.5; flat face (FF); body glass-fiber
reinforced vinyl ester (Derakane®); trim graphit-fiber
reinforced vinyl ester (Derakane®); seat PTFE®.
Manufacturer standard, max. pressure 275 psig.
*Note: The manufacturer shall be certificate of type approval.
VE-472C H3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; buttweld ends with nipple Sch
160; body ASTM A 182 Gr F 316L; AISI 316 trim; PEEK®
metallic seat; ASME B16.34 standard; class 2500.
VE-472D H3 Ball valve; fire tested ISO 10497 (API 607); full bore;
stainless steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; buttweld ends; body ASTM A
182 Gr F 316L; AISI 316 trim; PEEK® metallic seat; ASME
B16.34 standard; class 2500.
VE-473 B22 B23 B24 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 105 with organic
coted; AISI 410 trim; soft seat; ISO 14313 (API 6D) standard;
class 150.
VE-474 B22 B23 B24 Ball valve; full bore; carbon steel; bolted body; floating ball;
wrench (lever) operator, 90 degrees rotation; flanged ends
ASME B16.5; flat face (FF); body ASTM A 216 Gr WCB;
organic coated; AISI 410 trim; soft seat; ISO 14313 (API 6D)
standard; class 150.
VE-475 F16 Ball valve; full bore; duplex steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5, Ring type joint (RTJ); body-trim
ASTM A 995 Gr 4A (UNS J92205); PEEK® seat; ISO 14313
(API 6D) standard; class 900.
VE-476 F16 Ball valve; full bore; duplex steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 57 of 94
VE-477 F16 Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; wrench (lever)
operator, 90 degrees rotation; flanged ends ASME B16.5,
ring type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS
J92205); PEEK® / metallic seat; ISO 14313 (API 6D)
standard; class 900.
VE-478 F16 Ball valve; fire tested ISO 10497 (API 607); full bore; duplex
steel; bolted body; trunnion-mounted; handwheel gear
operator, 90 degrees rotation; flanged ends ASME B16.5 ring
type joint (RTJ); body-trim ASTM A 995 Gr 4A (UNS J92205);
PEEK® / metallic seat; ISO 14313 (API 6D) standard; class
900.
VE-479 H3 Ball valve; full bore; stainless stell; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 351 Gr CF8M; AISI 316 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 2500.
VE-480 H6 Ball valve; full bore; carbon steel; bolted body; trunnion
assembly; wrench (lever) operator, 90 degrees rotation;
buttweld with nipple XXS; body ASTM A 350 Gr LF2 CL1;
AISI 304 trim; PEEK® seat; ASME B16.34 LTD standard;
class 2500.
VE-481 H6 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 2500.
VE-482 H6 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LCB; AISI 304 trim; PEEK® seat; ISO 14313 (API
6D) standard; class 2500.
VE-483 H11 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; lateral wrench operator, 90 degrees rotation;
compact flanged NORSOK L-005; metallic seal joint (MSJ);
body ASTM A 216 Gr WCB; ASTM A 995 Gr 4A (UNS
J92205) trim; body-ball organic coated; PEEK® seat; ASME
B16.34 LTD standard; class 2500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 58 of 94
VE-484 H10 H14 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
compact flanged NORSOK L-005; metallic seal joint (MSJ);
body ASTM A 216 Gr WCB; AISI 410 trim; PEEK® seat;
ASME B16.34 LTD standard; class 2500.
VE-485 H30 H30P Ball valve; fire tested; full bore; bolted body; trunnion-
H33 H38 mounted; wrench (lever) operator, 90 degrees rotation;
H38P buttweld ends ASME B16.5; body ASTM B564 (UNS
N06625); AISI 410 trim; PEEK®/Metal seat; ISO 17292
standard; class 2500.
VE-486 E32 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 350 Grade LF3 with coated ASTM B564 (UNS N06625);
AISI 410 trim; RPTFE®/Metal seat; ISO 14313 (API 6D)
standard; class 600.
VE-487 F32 F33 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
socket weld ends ASME B16.5; body ASTM B 564 (UNS
N06625); AISI 410 trim; RPTFE®/Metallic seat; ISO 17292
standard; class 1500.
VE-488 F32 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 350 Gr LF3 with coated ASTM B 564 (UNS N06625); AISI
410 trim; PEEK®/Metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-489 F32 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 350 Gr LF3 with coated ASTM B 564 (UNS N06625); AISI
410 trim; PEEK®/Metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-490 E32 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring joint face (RTJ); body ASTM
A 350 Gr LF3 with coated ASTM B 564 (UNS N06625); ISO
14313 (API 6D) standard; AISI 410 trim; RPTFE®/Metal seat;
class 600.
VE-491 F32 Ball valve; fire tested; full bore; bolted body; trunnion-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 59 of 94
VE-492 F33 Ball valve; full bore; carbon steel; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 352 Gr LF2 with coated ASTM B564; AISI 304 trim; soft
seat; ISO 14313 (API 6D) standard; class 1500.
VE-493 F33 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; wrench (lever) operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 350 Gr LF2 with coated ASTM B 564 (UNS N06625); AISI
410 trim; PEEK®/Metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-494 F33 Ball valve; fire tested; full bore; bolted body; trunnion-
mounted; handwheel gear operator, 90 degrees rotation;
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 350 Gr LF2 with coated ASTM B 564 (UNS N06625); AISI
410 trim; PEEK®/Metallic seat; ISO 14313 (API 6D) standard;
class 900.
VE-495 H33 Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; wrench (lever) operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LF2 with coated ASTM B 564 (UNS
N06625); AISI 304 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 2500.
VE-496 H33 Ball valve; fire tested; full bore; carbon steel; bolted body;
trunnion-mounted; handwheel gear operator, 90 degrees
rotation; flanged ends ASME B16.5; ring type joint (RTJ);
body ASTM A 352 Gr LF2 with coated ASTM B 564 (UNS
N06625); AISI 304 trim; PEEK® seat; ISO 14313 (API 6D)
standard; class 2500.
VG-04 B9 B10 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel® wire; ISO
10434 (API 600) standard; class 150.
VG-04A B9 B10 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 60 of 94
VG-05 C9 C10 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5, raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; ISO 10434
(API 600) standard; class 300.
VG-05B C14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5, flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; ISO 10434
(API 600) standard; class 300.
VG-06 C9 C10 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; ISO 10434
(API 600) standard; class 300.
VG-06A C14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; flat
face (FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; ISO 10434
(API 600) standard; class 300.
VG-06B C14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.47 Series
A; flat face (FF); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
BS 1414 standard; ASME B16.34, face to face ASME
B16.10; class 300.
VG-07 C4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI 410
Stellite®; flexible graphite gasket with Inconel® wire; ISO
10434 (API 600) standard; class 300.
VG-07A C4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite®; flexible graphite gasket with Inconel®
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 61 of 94
VG-11 E9 E10 E10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
E14 E17 handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 600.
VG-12 F10 F10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
F14 non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel® wire; ISO
10434 (API 600) standard; class 900.
VG-13 F10 F10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
F14 handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 900.
VG-14 F10 F10R Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
F14 G10 non rising handwheel; flanged ends ASME B16.5; ring type
G10R G14 joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
G18 AISI 410; flexible graphite gasket with Inconel® wire; ISO
10434 (API 600) standard; class 1500.
VG-15 G10 G10R Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
G14 G18 handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 1500.
VG-16 H10 H14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5, ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel® wire; ISO
10434 (API 600) standard; class 2500.
VG-17 H10 H14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5, ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 2500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 62 of 94
VG-34 A4 A8 Gate valve; F°F°; bolted bonnet; solid wedge; OS&Y; non
rising handwheel; flanged ends ASME B16.1; flat face (FF);
body ASTM A 126 class CL B; trim (wedge-seat) ASTM B62
(UNS C83600); PTFE gasket; MSS SP-70 standard; class
125.
VG-36 A4 B7 B7R Gate valve; brass; union bonnet; solid wedge; OS&Y; rising
B22 B23 handwheel; screwed ends ASME B1.20.1 NPT; body ASTM
B24 B62 (UNS C83600); trim (wedge-seat) ASTM B62 (UNS
C83600); PTFE gasket; MSS SP-80 standard; max. pressure
250 psi.
VG-39 B4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI 410
Stellite®; flexible graphite gasket with Inconel® wire; ISO
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 64 of 94
VG-39A B4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite®; flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 150.
VG-45 B4 B9 B10 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
B17 C4 C9 non rising handwheel; socket weld ends; body ASTM A 105;
C10 E4 E9 trim (wedge-seat) AISI 410 Stellite®; flexible graphite gasket
E10 E10R with Inconel® wire; ISO 15761 (API 602) standard; class 800.
E17
VG-46 F4 F10 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
F10R G4 non rising handwheel; socket weld ends; body ASTM A 105
G10 G10R trim (wedge-seat) AISI 304 Stellite®; flexible graphite gasket
G18 with Inconel® wire; ISO 15761 (API 602) standard; class
1500.
VG-50 B13 C13 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; socket weld ends;
body-wedge-seat ASTM A 182 Gr F53 (UNS S32750);
flexible graphite gasket with Inconel® wire; ISO 15761 (API
602) standard; class 800.
VG-51 B12 C12 Gate valve; stainless steel superduplex; bolted bonnet, solid
wedge; OS&Y; non rising handwheel; socket weld ends;
body-wedge-seat ASTM A 182 Gr F55 (UNS S32760);
flexible graphite gasket with Inconel® wire; ISO 15761 (API
602) standard; class 800.
VG-55 B12 B13 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; raised face (RF); body-wedge-seat ASTM A 995 Gr
5A (UNS J93404); flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 150.
VG-56 B12 B13 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; raised face (RF); body-wedge-seat ASTM A
995 Gr 5A (UNS J93404); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-56A B12 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.47 Series A; raised face (RF); body-wedge-seat
ASTM A 995 Gr 5A (UNS J93404); flexible graphite gasket
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 65 of 94
VG-57 C12 C13 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; raised face (RF); body-wedge-seat ASTM A 995 Gr
5A (UNS J93404); flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 300.
VG-58 C12 C13 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; raised face (RF); body-wedge-seat ASTM A
995 Gr 5A (UNS J93404); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 300.
VG-61 E4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite®; flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 600.
VG-62 E4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410 Stellite®; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 600.
VG-63 F4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite®; flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 900.
VG-64 F4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410 Stellite®; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 900.
VG-65 F4 G4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410 Stellite®; flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 1500.
VG-66 G4 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 66 of 94
VG-67 G12 Gate valve; stainless steel superduplex; bolted bonnet, solid
wedge; OS&Y; non rising handwheel; socket weld ends;
body-wedge-seat ASTM A 182 Gr F55 (UNS S32760);
flexible graphite gasket with Inconel® wire; ISO 15761 (API
602) standard; class 1500.
VG-68 G12 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body-wedge-seat ASTM A 995
Gr 5A (UNS J93404); flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 1500.
VG-69 G12 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; ring type joint (RTJ); body-wedge-seat ASTM A
995 Gr 5A (UNS J93404); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 1500.
VG-70 B11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; trim (wedge-seat) AISI 304
Stellite®; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 15761 (API 602) standard;
class 150.
VG-71 B7 B7R B11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket
with Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-72 B7 B7R B11 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-72A B7 B7R Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.47 Series
A; raised face (RF); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 67 of 94
VG-73 F11 G11 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 105 trim (wedge-seat) AISI 304
Stellite®; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 15761 (API 602) standard;
class 1500.
VG-74 F11 G11 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 1500.
VG-75 G11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 1500.
VG-76 H11 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 2500.
VG-77 H11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 2500.
VG-78 F11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 900.
VG-79 F11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 68 of 94
VG-81 C11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket
with Inconel® wire; ISO 10434 (API 600) standard; class 300.
VG-82 C11 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 300.
VG-83 E11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RTJ); body ASTM A 105; trim (wedge-seat) AISI 410;
body-wedge organic coated; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 600.
VG-84 E11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
class 600.
VG-85 C11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 105; trim (wedge-seat) AISI 304
Stellite®; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 15761 (API 602) standard;
class 300.
VG-86 E11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; ring type
joint (RT); body ASTM A 105; trim (wedge-seat) AISI 304
Stellite®; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 15761 (API 602) standard;
class 600.
VG-87 J12 Gate valve, conduit type; full bore, stainless steel
superduplex, body-trim ASTM A 995 Gr 5A (UNS J93404)
bolted bonnet, non rising stem, non rising handwheel; flanged
ends API 6BX; ring joint type; ISO 10423 (API 6A) standard;
max. pressure 10000 psi; with stem balancing.
VG-88 B16 C16 Gate valve; stainless steel duplex; bolted bonnet; solid
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 69 of 94
VG-89 B16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; raised face (RF); body-wedge-seat ASTM A 995 Gr
4A (UNS J92205); flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 150.
VG-90 B16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; raised face (RF); body-wedge-seat ASTM A
995 Gr 4A (UNS J92205); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-90A B16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.47 Series A; raised face (RF); body-wedge-seat
ASTM A 995 Gr 4A (UNS J92205); flexible graphite gasket
with Inconel® wire; ISO 10434 (API 600) standard; ASME
B16.34, face to face ASME B16.10; class 150.
VG-92 C16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; raised face (RF); body-wedge-seat ASTM A 995 Gr
4A (UNS J92205); flexible graphite gasket with Inconel® wire;
ISO 10434 (API 600) standard; class 300.
VG-93 C16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; raised face (RF); body-wedge-seat ASTM A
995 Gr 4A (UNS J92205); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 300.
VG-95 E16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body-wedge-seat ASTM A 995
Gr 4A (UNS J92205); flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 600.
VG-96 E16 Gate valve; stainless steel duplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; ring type joint (RTJ); body-wedge-seat ASTM A
995 Gr 4A (UNS J92205); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 600.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 70 of 94
VG-97 F16 G16 Gate valve; stainless steel duplex; bolted bonnet, solid
G16P wedge; OS&Y; non rising handwheel; socket weld ends;
body-wedge-seat ASTM A 182 Gr F 51 (UNS S31803);
flexible graphite gasket with Inconel® wire; ISO 15761 (API
602) standard; class 1500.
VG-98 F16 G16 Gate valve; stainless steel superduplex; bolted bonnet; solid
G16P wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body-wedge-seat ASTM A 995
Gr 4A (UNS J92205); flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 1500.
VG-99 G16 G16P Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; ring type joint (RTJ); body-wedge-seat ASTM A
995 Gr 4A (UNS J92205); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 1500.
VG-100 A8 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; flat face
(FF); body ASTM A 105; trim (wedge-seat) AISI 304 Stellite®;
flexible graphite gasket with Inconel® wire; ISO 15761 (API
602) standard; class 150.
VG-109B B23 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket
with Inconel® wire; ISO 10434 (API 600) standard; class 150.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 71 of 94
VG-110A B23 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; flat
face (FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; body-wedge organic coated; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-110B B23 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.47 Series
A; flat face (FF); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; body-wedge organic coated; flexible graphite
gasket with Inconel® wire; ISO 10434 (API 600) standard;
ASME B16.34, face to face ASME B16.10; class 150.
VG-111 B14 Gate valve; carbon steel; bolted bonnet, solid wedge; OS&Y;
handwheel gear operator; flenged ends ASME B16.5; flat
face (FF); body ASTM A 216 Gr WCB; body-trim (wedge-
seat) AISI 410; organic coated; flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 150.
VG-112 B22 B23 B24 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; organic
coated; ISO 10434 (API 600) standard; class 150.
VG-113 B22 B23 B24 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.5; flat
face (FF); body ASTM A 216 Gr WCB; trim (wedge-seat)
AISI 410; flexible graphite gasket with Inconel® wire; organic
coated; ISO 10434 (API 600) standard; class 150.
VG-113A B22 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.47 Series
A; flat face (FF); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
organic coated; BS 1414 standard; ASME B16.34; face to
face ASME B16.10; class 150.
VG-114 B9 B10 B17 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; raised face
(RF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
410; flexible graphite gasket with Inconel® wire; ISO 10434
(API 600) standard; class 150.
VG-114A B14 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
non rising handwheel; flanged ends ASME B16.5; flat face
(FF); body ASTM A 216 Gr WCB; trim (wedge-seat) AISI
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 72 of 94
VG-115 F16 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; non rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body-wedge-seat ASTM A 995
Gr 4A (UNS J92205); flexible graphite gasket with Inconel®
wire; ISO 10434 (API 600) standard; class 900.
VG-116 F16 Gate valve; stainless steel superduplex; bolted bonnet; solid
wedge; OS&Y; handwheel gear operator; flanged ends
ASME B16.5; ring type joint (RTJ); body-wedge-seat ASTM A
995 Gr 4A (UNS J92205); flexible graphite gasket with
Inconel® wire; ISO 10434 (API 600) standard; class 900.
VG-117 H11 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; compact flanged NORSOK L-005;
metallic seal joint (MSJ); body ASTM A 216 Gr WCB; trim
(wedge-seat) AISI 410; body-wedge organic coated; flexible
graphite gasket with Inconel® wire; ISO 10434 (API 600)
standard; class 2500.
VG-118 C9 Gate valve; carbon steel; bolted bonnet; solid wedge; OS&Y;
handwheel gear operator; flanged ends ASME B16.47 Series
A; raised face (RF); body ASTM A 216 Gr WCB; trim (wedge-
seat) AISI 410; flexible graphite gasket with Inconel® wire;
BS 1414 standard; class 300.
VG ABRAS-04 B5 C5 E5 Gate valve; abrasive; mud type; full bore; stainless steel;
bolted bonnet; OS&Y; non rising handwheel; flanged ends
API 6B; ring type joint (RTJ); body ASTM A 487 Gr 9N; solid
wedge AISI 316; buna N seat; max. pressure 2000 psi.
VG ABRAS-05 F5 Gate valve; abrasive; mud type; full bore; stainless steel;
bolted bonnet; OS&Y; non rising handwheel; flanged ends
API 6B; ring type joint (RTJ); body ASTM A 487 Gr 9N; solid
wedge AISI 316; buna N seat; max. pressure 3000 psi.
VG ABRAS-06 G5 Gate valve; abrasive; mud type; full bore; stainless steel;
bolted bonnet; OS&Y; non rising handwheel; flanged ends API
6B; ring type joint (RTJ); body ASTM A 487 Gr 9N; solid
wedge AISI 316; buna N seat; max. pressure 5000 psi.
VG ABRAS-07 H5 Gate valve; abrasive; mud type; full bore; stainless steel;
bolted bonnet; OS&Y; non rising handwheel; flanged ends
API 6B; ring type joint (RTJ); body ASTM A 487 Gr 9N; solid
wedge AISI 316; buna N seat; max. pressure 10000 psi.
VG ABRAS-08 J5 Gate valve; abrasive; mud type; full bore; stainless steel;
bolted bonnet; OS&Y; non rising handwheel; flanged ends
API 6B; ring type joint (RTJ); body ASTM A 487 Gr 9N; solid
wedge AISI 316; buna N seat; max. pressure 10000 psi.
VGL-03 B9 B10 B17 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 216 Gr WCB; body-
seat AISI 410; BS 1873 standard; class 150.
VGL-03A B14 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; flat face (FF); body ASTM A 216 Gr WCB; body-seat
AISI 410; BS 1873 standard; class 150.
VGL-04 C9 C10 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 216 Gr WCB; body-
seat AISI 410; BS 1873 standard; class 300.
VGL-07 E9 E10 E10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
E14 E17 outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
body-seat AISI 410; BS 1873 standard; class 600.
VGL-07E E9 E10 E10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
E14 E17 outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 600.
VGL-08 F10 F10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
F14 outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
body-seat AISI 410; BS 1873 standard; class 900.
VGL-08E F10 F10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
F14 outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 900.
VGL-09 F10 F10R Globe valve; carbon steel; bolted bonnet; chamfer disc;
F14 G10 outside screw stem; rising handwheel; flanged ends ASME
G10P G10R B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 74 of 94
VGL-09E G10 G10P Globe valve; carbon steel; bolted bonnet; chamfer disc;
G10R G14 outside screw stem; lateral wrench operator; flanged ends
G18 ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 1500.
VGL-16 A4 B7 B7R Globe valve; brass; union bonnet; chamfer disc; inside screw
stem; screw ends; ASME B1.20.1 NPT; body-disc-seat
ASTM B62; MSS SP-80 standard; class 150.
VGL-18 A4 A8 Globe valve; F°F°; bolted bonnet; cham fer disc; outside screw
stem; rising handwheel; flanged ends ASME B16.1; flat face
(FF); body ASTM A126 CL B; trim (disc-seat) ASTM B62;
CEN EN 13789 standard; class 125.
VGL-19 H10 H14 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB; body-
seat AISI 410; BS 1873 standard; class 2500.
VGL-19E H10 H14 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; BS 1873 standard; class 2500.
VGL-22 B6 B19 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 352 Gr LCB; trim
(disc-seat) AISI 304; BS 1873 standard; class 150.
VGL-24 E6 E6R Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 352 Gr LCB; trim
(disc-seat) AISI 304; BS 1873 standard; class 600.
VGL-24E E6 E6R Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 352 Gr
LCB; trim (disc-seat) AISI 304; BS 1873 standard; class 600.
VGL-28 F6 F6R G6 Globe valve; carbon steel; bolted bonnet; chamfer disc;
G6R G19 outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 352 Gr LCB; trim
(disc-seat) AISI 304; BS 1873 standard; class 1500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 76 of 94
VGL-28E G6 G6R Globe valve; carbon steel; bolted bonnet; chamfer disc;
G19 outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 352 Gr
LCB; trim (disc-seat) AISI 304; BS 1873 standard; class
1500.
VGL-29 F6 F6R Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 352 Gr LCB; trim
(disc-seat) AISI 304; BS 1873 standard; class 900.
VGL-29E F6 F6R Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 352 Gr
LCB; trim (disc-seat) AISI 304; BS 1873 standard; class 900.
VGL-31 A4 B7 B7R Globe valve angular; for hydrant with adapter and cap; brass;
screwed bonnet; plain disc with ring; inside screw stem; rising
handwheel; inlet screw female end ASME B1.20.1 NPT;
outlet screw male end NFPA 1693 2,5-7,5 NH; with adapter
for hose; with cap and chain; body trim (disc-seat) ASTM
B62; angle 90 degrees; max. pressure 200 psi.
VGL-37 B12 B13 Globe valve; stainless steel superduplex; bolted bonnet;
chamfer disc; OS&Y; outside screw; rising handwheel;
flanged ends ASME B16.5; raised face (RF); body-disc-seat
ASTM A 995 Gr 5A (UNS J93404); BS 1873 standard; class
150.
VGL-38 C12 C13 Globe valve; stainless steel superduplex; bolted bonnet;
chamfer disc; OS&Y; outside screw; rising handwheel;
flanged ends ASME B16.5; raised face (RF); body-disc-seat
ASTM A 995 Gr 5A (UNS J93404); BS 1873 standard; class
300.
VGL-39 B25 Globe valve; stainless steel; bolted bonnet; chamfer disc;
OS&Y; outside screw; rising handwheel; flanged ends ASME
B16.5; flat face (FF); body ASTM A 351 Gr CD4MCU; solid
wedge AISI 316L; BS 1873 standard; class 150.
VGL-41 B7 B7R B11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
B14 B15 outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 216 Gr WCB; trim
(disc-seat) AISI 410; body-trim organic coated; BS 1873
standard; class 150.
VGL-42 F11 G11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 78 of 94
VGL-42E G11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-seat AISI 410; body-trim organic coated; BS
1873 standard; class 1500.
VGL-43 H11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB;
body-seat AISI 410; body-trim organic coated; BS 1873
standard; class 2500.
VGL-43E H11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; body-trim organic coated; BS 1873 standard; class
2500.
VGL-44 F11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB; trim
(disc-seat) AISI 410; body-trim organic coated; BS 1873
standard; class 900.
VGL-44E F11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operador; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 216 Gr
WCB; trim (disc-seat) AISI 410; body-trim organic coated; BS
1873 standard; class 900.
VGL-45 C11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; raised face (RF); body ASTM A 216 Gr WCB; trim
(disc-seat) AISI 410; body-trim organic coated; BS 1873
standard; class 300.
VGL-46 E11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 216 Gr WCB; trim
(disc-seat) AISI 410; body-trim organic coated; BS 1873
standard; class 600.
VGL-46E E11 Globe valve; carbon steel; bolted bonnet; chamfer disc;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 79 of 94
VGL-47 B16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw; rising handwheel; flanged ends
ASME B16.5; raised face (RF); body-disc-seat ASTM A 995
Gr 4A (UNS J92205); BS 1873 standard; class 150.
VGL-48 J40 Globe valve; Nickel alloy steel; bolted bonnet; chamfer disc;
OS&Y; outside screw; lateral gear operator; metallic seal joint
(MSJ); finishing as NORSOK L-005; body ASTM B564 (UNS
N06625; (disc-seat) ASTM B564 (UNS N06625); API 6A;
max. pressure 10000 psi.
VGL-84 C16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw; rising handwheel; flanged ends
ASME B16.5; raised face (RF); body-disc-seat ASTM A 995
Gr 4A (UNS J92205); BS 1873 standard; class 300.
VGL-85 E16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw stem; rising handwheel; flanged
ends ASME B16.5; ring type joint (RTJ); body-disc-seat
ASTM A 995 Gr 4A (UNS J92205); BS 1873 standard; class
600.
VGL-86 E16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw stem; lateral wrench operator;
flanged ends ASME B16.5; ring type joint (RTJ); body-disc-
seat ASTM A 995 Gr 4A (UNS J92205); BS 1873 standard;
class 600.
VGL-87 F16 G16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
G16P disc; OS&Y; outside screw; rising handwheel; flanged ends
ASME B16.5; ring type joint (RTJ); body-disc-seat ASTM A
995 Gr 4A (UNS J92205); BS 1873 standard; class 1500.
VGL-88 G16 G16P Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw stem; lateral wrench operator;
flanged ends ASME B16.5; ring type joint (RTJ); body-disc-
seat ASTM A 995 Gr 4A (UNS J92205); BS 1873 standard;
class 1500.
VGL-92 H30 H30P Globe valve; carbon steel with Inconel®625; bolted bonnet;
H38 H38P chamfer disc; OS&Y; outside screw; rising handwheel;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 80 of 94
flanged ends ASME B16.5; ring type joint (RTJ); body ASTM
A 216 Gr WCB with ASTM B564 (UNS N06625); trim (disc-
seat) AISI 410; class 2500.
VGL-94 J31 Globe valve; Nickel alloy steel; bolted bonnet; chamfer disc;
OS&Y; outside screw; lateral gear operator; metallic seal joint
(MSJ); finishing as NORSOK L-005; body ASTM A 522 Type
I trim (disc-seat) ASTM A 522 Type I; API 6A; max. pressure
10000 psi.
VGL-95 E30 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 216 Gr WCB with ASTM B564
(UNS N06625); trim (disc-seat) AISI 410; class 600.
VGL-96 C30 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; raised
face (RF); body ASTM A 216 Gr WCB with ASTM B564
(UNS N06625); BS 1873 standard; trim (disc-seat) AISI 410;
class 300.
VGL-97 C14 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16; flat face (FF); body ASTM A 216 Gr WCB; trim (disc-
seat) AISI 410; body-trim organic coated; BS 1873 standard;
class 300.
VGL-97B B22 B23 B24 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; flat face (FF); body ASTM A 216 Gr WCB; trim (disc-
seat) AISI 410; body-trim organic coated; BS 1873 standard;
class 150.
VGL-98 F16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw; rising handwheel; flanged ends
ASME B16.5; ring type joint (RTJ); body-disc-seat ASTM A
995 Gr 4A (UNS J92205); BS 1873 standard; class 900.
VGL-99 F16 Globe valve; stainless steel duplex; bolted bonnet; chamfer
disc; OS&Y; outside screw stem; lateral wrench operator;
flanged ends ASME B16.5; ring type joint (RTJ); body-disc-
seat ASTM A 995 Gr 4A (UNS J92205); BS 1873 standard;
class 900.
VGL-101 E32 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 350 Gr LF3 with coated ASTM
B564 (UNS N06625); trim (disc-seat) AISI 410; class 600.
VGL-102 F32 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
joint type (RTJ); body ASTM A 350 Gr LF3 with coated ASTM
B 564 (UNS N06625); trim (disc-seat) AISI 410; BS 1873
standard; class 1500.
VGL-103 F32 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
joint type (RTJ); body ASTM A 350 Gr LF3 with coated ASTM
B 564 (UNS N06625); trim (disc-seat) AISI 410; BS 1873
standard; class 900.
VGL-103E F32 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; lateral wrench operador; flanged ends ASME B16.5;
ring joint type (RTJ); body ASTM A 350 Gr LF3 with coated
ASTM B 564 (UNS N06625); trim (disc-seat) AISI 410; BS
1873 standard; class 900.
VGL-104 F33 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
joint type (RTJ); body ASTM A 350 Gr LF2 with coated ASTM
B 564 (UNS N06625); trim (disc-seat) AISI 410; BS 1873
standard; class 1500.
VGL-105 F33 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; rising handwheel; flanged ends ASME B16.5; ring
joint type (RTJ); body ASTM A 350 Gr LF2 with coated ASTM
B 564 (UNS N06625); trim (disc-seat) AISI 410; BS 1873
standard; class 900.
VGL-106 F33 Globe valve; bolted bonnet; chamfer disc; OS&Y; outside
screw; lateral wrench operador; flanged ends ASME B16.5;
ring joint type (RTJ); body ASTM A 350 Gr LF2 with coated
ASTM B 564 (UNS N06625); trim (disc-seat) AISI 410; BS
1873 standard; class 900.
VGL-107 H33 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; rising handwheel; flanged ends ASME
B16.5; ring type joint (RTJ); body ASTM A 352 Gr LF2 with
coated ASTM B 564 (UNS N06625); trim (disc-seat) AISI
304; BS 1873 standard; class 2500.
VGL-108 H33 Globe valve; carbon steel; bolted bonnet; chamfer disc;
outside screw stem; lateral wrench operator; flanged ends
ASME B16.5; ring type joint (RTJ); body ASTM A 352 Gr
LF2 with coated ASTM B 564 (UNS N06625); trim (disc-seat)
AISI 304; BS 1873 standard; class 2500.
VR-03 F4 F10 Check valve; horizontal; globe type; carbon steel; bolted
F10R G4 bonnet; chamfer piston disc; socket weld ends MSS SP-84;
G10 G10R body ASTM A 105; disc-seat AISI 304-Stellite®; ISO 15761
G18 (BS 5352) standard; class 1500.
VR-25 A4 B7 B7R Check valve; swing type; brass; screwed bonnet; screw ends
ASME B1.20.1 NPT; body-disc-seat ASTM B62; MSS SP-80
standard; class 200.
VR-28 B9 B10 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410; metal-metal; API 594
standard; class 150.
VR-28A B9 B10 Check valve; wafer; dual plate type; carbon steel; raised face
(RF) ASME B16.47 Series A; finishing as MSS SP-6; body-
disc ASTM A 216 Gr WCB; spring Inconel®; stem AISI 410;
metal-metal; API 594 standard; class 150.
VR-29 C9 C10 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410; metal-metal; API 594
standard; class 300.
VR-35 B5 B9 B10 Check valve; wafer; dual plate type; carbon steel; raised face
B17 (RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; Viton seat TBR-S; API
594 standard; class 150.
VR-35A B9 B10 Check valve; wafer; dual plate type; carbon steel; raised
face (RF) ASME B16.47 series A; finishing as MSS SP-6;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 83 of 94
VR-36 C5 C9 C10 Check valve; wafer; dual plate type; carbon steel; raised
face (RF); finishing as; body-disc ASTM A 216 Gr WCB;
spring Inconel®; stem AISI 316; Viton seat TBR-S; API 594
standard; class 300.
VR-38 E5 E9 E10 Check valve; wafer; dual plate type; carbon steel; ring type
E10R E17 joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel®; stem AISI 316; Viton seat TBR-S;
API 594 standard; class 600.
VR-39 F5 F10 Check valve; wafer; dual plate type; carbon steel; ring type
F10R joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel®; stem AISI 316; Viton seat TBR-S;
API 594 standard; class 900.
VR-40 F5 F10 Check valve; wafer; dual plate type; carbon steel; ring type
F10R G5 joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
G10 G10R Gr WCB; spring Inconel®; stem AISI 316; Viton seat TBR-S;
G18 API 594 standard; class 1500.
VR-41 H5 H10 H14 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216
Gr WCB; spring Inconel®; stem AISI 316; Viton seat; API
594 standard; class 2500.
VR-42 B3 Check valve; wafer; dual plate type; stainless steel; raised
face (RF); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 150.
VR-43 C3 Check valve; wafer; dual plate type; stainless steel; raised
face (RF); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 300.
VR-45 E3 Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 600.
VR-46 F3 Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 900.
VR-47 F3 G3 Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 1500.
VR-48 H3 Check valve; wafer; dual plate type; stainless steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; Viton seat TBR-S; API 594
standard; class 2500.
VR-49 A4 A8 Check valve; wafer; dual plate type; F°F°; flat face (FF);
finishing as MSS SP-6; body ASTM A 126 class B; disc
brass ASTM B584; spring stem AISI 316; Viton seat; API 594
standard; class 125.
VR-52 B6 B19 C6 Check valve; horizontal; globe type; carbon steel; bolted
E6 E6R bonnet; chamfer piston disc; socket weld ends MSS SP-84;
body ASTM A 350 Gr LF2 CL1; disc-seat AISI 304; ISO
15761 (BS 5352) standard; class 800.
VR-53 B6 B19 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 352 Gr LCB;
spring Inconel®; stem AISI 304; Viton seat TBR-S; API 594
standard; class 150.
VR-53A B6 B19 Check valve; wafer; dual plate type; carbon steel; raised face
(RF) ASME B16.47 Series A; finishing as MSS SP-6; body-
disc ASTM A 352 Gr LCB; spring Inconel®; disc AISI 304;
Viton seat TBR-S; API 594 standard; class 150.
VR-54 C6 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 352 Gr LCB;
spring Inconel®; stem AISI 304; Viton seat TBR-S; API 594
standard; class 300.
VR-55 E6 E6R Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel®; stem AISI 304; Viton seat; API 594
standard; class 600.
VR-56 B4 B17 C4 Check valve; horizontal; globe type; carbon steel; bolted
C9 C10 E4 bonnet; chamfer piston disc; socket weld ends MSS SP-84;
E9 E10 body ASTM A 105; disc-seat AISI 304-Stellite®; ISO 15761
E10R E17 (BS 5352) standard; class 800.
VR-58 F6 F6R G6 Check valve; horizontal; globe type; carbon steel; bolted
G6R G19 bonnet; chamfer piston disc; socket weld ends MSS SP-84;
body ASTM A 350 Gr LF2 CL1; disc-seat AISI 304; ISO
15761 (BS 5352) standard; class 1500.
VR-59 F6 F6R G6 Check valve; wafer; dual plate type; carbon steel; ring type
G6R G19 joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel®; stem AISI 304; Viton seat; API 594
standard; class 1500.
VR-60 F6 F6R Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel®; stem AISI 304; Viton seat; API 594
standard; class 900.
VR-65 C14 Check valve; wafer; dual plate type; carbon steel; flat face
(FF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 300.
VR-65A C14 Check valve; wafer; dual plate type; carbon steel; flat face
(FF) ASME B16.47 Series A; finishing as MSS SP-6; body-
disc ASTM A 216 Gr WCB; spring stem AISI 316; Viton seat;
API 594 standard; class 300.
VR-66 E14 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 600.
VR-67 F14 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 900.
VR-68 F14 G14 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring stem AISI 316; Viton seat; API 594 standard;
class 1500.
VR-71 B6 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body ASTM A 352 Gr LCB;
spring Inconel®; disc AISI 410-Stellite®; metal-metal; API
594 standard; class 150.
VR-71A B6 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); ASME B16.47 Series A; finishing as MSS SP-6; body-
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 86 of 94
VR-72 B12 B13 Check valve; wafer; dual plate type; stainless steel
superduplex; raised face (RF); finishing as MSS SP-6; body-
disc-stem ASTM A 995 Gr 5A (UNS J93404); Viton seat
TBR-S; API 594 standard; class 150.
VR-72A B12 Check valve; wafer; dual plate type; stainless steel
superduplex; raised face (RF) ASME B16.47 Series A;
finishing as MSS SP-6; body-disc-stem ASTM A 995 Gr 5A
(UNS J93404); Viton seat TBR-S; API 594 standard; class
150.
VR-73 C12 C13 Check valve; wafer; dual plate type; stainless steel
superduplex; raised face (RF); finishing as MSS SP-6; body-
disc-stem ASTM A 995 Gr 5A (UNS J93404); Viton seat
TBR-S; API 594 standard; class 300.
VR-74 B3 Check valve; wafer; dual plate type; stainless steel; raised
face (RF); finishing as MSS SP-6; body-disc-stem ASTM A
351 Gr CF8M; spring Inconel®; metal-metal; API 594
standard; class 150.
VR-76 B4 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; Viton seat
TBR-S; API 594 standard; class 150.
VR-77 B4 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; metal-metal;
API 594 standard; class 150.
VR-78 B6 B19 Check valve; horizontal; globe type; piston-disc with damping;
carbon steel; bolted bonnet; flanged ends ASME B16.5;
raised face (RF); body ASTM A 352 Gr LCB; disc AISI 304;
Viton seat TBR-S; BS 1868 standard; class 150.
VR-80 E6 E6R Check valve; horizontal; globe type; piston-disc with damping;
carbon steel; bolted bonnet; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 352 Gr LCB; disc AISI 304;
Viton seat; BS 1868 standard; class 600.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 87 of 94
VR-81 F6 F6R Check valve; horizontal; globe type; piston-disc with damping;
carbon steel; bolted bonnet; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 352 Gr LCB; disc AISI 304;
Viton seat; BS 1868 standard; class 900.
VR-82 F6 F6R G6 Check valve; horizontal; globe type; piston-disc with damping;
G6R G19 carbon steel; bolted bonnet; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 352 Gr LCB; disc AISI 304;
Viton seat; BS 1868 standard; class 1500.
VR-86 B13 C13 Check valve; horizontal; globe type; stainless steel
superduplex; bolted bonnet; chamfer piston disc; socket weld
ends MSS SP-84; body-disc-seat ASTM A 182 Gr F53 (UNS
S32750); ISO 15761 (BS 5352) standard; class 800.
VR-87 B12 C12 Check valve; horizontal; globe type; stainless steel
superduplex; bolted bonnet; chamfer piston disc; socket weld
ends MSS SP-84; body-trim ASTM A 182 Gr F55 (UNS
S32760); PTFE® reinforced with 25% de carbon seat; class
800.
VR-88 B21 Check valve; ball type; socket weld ends; body-ball CPVC;
flat face (FF); class 150 psig.
VR-89 B20 Check valve; ball type; socket weld ends; body-ball PVC; flat
face (FF); class 150 psig.
VR-90 B25 Check valve; wafer; dual plate type; stainless steel; flat face
(FF); finishing as MSS SP-6; body ASTM A 351 Gr CD4MCU;
disc-spring AISI 316L; Hypalon seat; API 594 standard; class
150.
VR-91 B25 Check valve; horizontal; globe type; stainless steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; flat
face (FF); body ASTM A 351 Gr CD4MCU; disc-spring AISI
316L; Hypalon seat; BS 1868 standard; class 150.
VR-92 B14 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; flat
face (FF); body ASTM A 105; disc-seat AISI 410; BS 1868
standard; class 150.
VR-93 C14 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; flat
face (FF); body ASTM A 105; disc-seat AISI 410; BS 1868
standard; class 300.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 88 of 94
VR-94 E14 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 105; disc-seat AISI 410; BS
1868 standard; class 600.
VR-95 F14 G14 Checkvalve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 105; disc-seat AISI 410;
ASME B16.34 LTD standard; class 1500.
VR-96 C4 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; Viton seat
TBR-S; API 594 standard; class 300.
VR-97 C4 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; metal-metal;
API 594 standard; class 300.
VR-98 E4 E8 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; Viton seat
TBR-S; API 594 standard; class 600.
VR-99 E4 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; metal-metal;
API 594 standard; class 600.
VR-100 F4 G4 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; Viton seat
TBR-S; API 594 standard; class 1500.
VR-101 F4 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; metal-metal;
API 594 standard; class 900.
VR-102 F4 G4 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410-Stellite®; metal-metal;
API 594 standard; class 1500.
VR-103 F4 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 89 of 94
VR-105 G12 Check valve; wafer; dual plate type; stainless steel
superduplex; ring type joint (RTJ); finishing as MSS SP-6;
body-disc-stem ASTM A 995 Gr 5A (UNS J93404); Viton seat
TBR-S; API 594 standard; class 1500.
VR-107 B11 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged end ASME B16.5;
raised face (RF); body ASTM A 105; disc-seat AISI 304-
Stellite®; body-trim organic coated; ISO 15761 (BS 5352)
standard; class 150.
VR-108 B7 B7R B11 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; body-trim organic
coated; API 594 standard; class 150.
VR-108A B7 B7R B11 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); ASME B16.47 Series A; finishing as MSS SP-6; body-
disc ASTM A 216 Gr WCB; spring Inconel®; stem AISI 316;
body-trim organic coated; API 594 standard; class 150.
VR-109 F11 G11 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged ends ASME B16.5; ring
type joint (RTJ); body ASTM A 105; disc-seat AISI 304-
Stellite®; body-trim organic coated; ISO 15761 (BS 5352)
standard; class 1500.
VR-110 F11 G11 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; body-trim organic
coated; API 594 standard; class 1500.
VR-111 H11 Check valve; horizontal; globe type; carbon steel; bolted body;
chamfer piston disc; ring type joint (RTJ); body ASTM A 105;
disc-seat AISI 304; body-trim organic coated; ISO 15761 (BS
5352) standard; class 2500.
VR-112 H11 Check valve; wafer; dual plate type; carbon steel; ring type
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 90 of 94
VR-114 F11 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; body-trim organic
coated; API 594 standard; class 900.
VR-115 C11 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; body-trim organic
coated; API 594 standard; class 300.
VR-116 E11 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 316; body-trim organic
coated; API 594 standard; class 600.
VR-117 C11 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged end ASME B16.5; raised
face (RF); body ASTM A 105; disc-seat AISI 304-Stellite®;
body-trim organic coated; ISO 15761 (BS 5352) standard;
class 300.
VR-118 E11 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; flanged end ASME B16.5; ring
type joint (RTJ); body ASTM A 105; disc-seat AISI 304-
Stellite®; body-trim organic coated; ISO 15761 (BS 5352)
standard; class 600.
VR-119 B16 C16 Check valve; horizontal; globe type; stainless steel duplex;
E16 bolted bonnet; chamfer piston disc; socket weld ends MSS
SP-84; body-disc-seat ASTM A 182 Gr F51 (UNS S31803);
ISO 15761 (BS 5352) standard; class 800.
VR-120 B16 Check valve; wafer; dual plate type; stainless steel duplex;
raised face (RF); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; API
594 standard; class 150.
VR-120A B16 Check valve; wafer; dual plate type; stainless steel duplex;
raised face (RF) ASME B16.47 Series A; finishing as MSS
SP-6; body-disc-stem ASTM A 995 Gr 4A (UNS J92205);
Viton seat TBR-S; API 594 standard; class 150.
VR-122 C16 Check valve; wafer; dual plate type; stainless steel duplex;
raised face (RF); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; spring
Inconel®; API 594 standard; class 300.
VR-124 E16 Check valve; wafer; dual plate type; stainless steel duplex;
raised face (RF); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; spring
Inconel®; API 594 standard; class 600.
VR-125 F16 G16 Check valve; horizontal; globe type; stainless steel duplex;
G16P bolted bonnet; chamfer piston disc; socket weld ends MSS
SP-84; body-disc-seat ASTM A 182 Gr F51 (UNS S31803);
ISO 15761 (BS 5352) standard; class 1500.
VR-126 F16 G16 Check valve; wafer; dual plate type; stainless steel duplex;
G16P ring type joint (RTJ); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; spring
Inconel®; API 594 standard; class 1500.
VR-132 H30 H33 Check valve; horizontal; globo type; ASTM B564 (UNS
H38 N06625); bolted bonnet; chamfer piston disc; buttweld ends
ASME B16.25; body-disc-seat ASTM B564 (UNS N06625);
ASME B16.34 standard; class 2500.
VR-133 H30 H38 Check valve; wafer; dual plate type; carbon steel with ASTM
B564 (UNS N06625); ring type joint (RTJ); fishing as MSS
SP-6; body-disc-stem ASTM A 216 Gr WCB with coated
ASTM B564 (UNS N06625); spring Inconel®; Viton seat TBR-
S; API 594 standard; class 2500.
VR-136 H10 H14 Check valve; horizontal; globo type; carbon steel; bolted
bonnet; chamfer piston disc; buttweld ends ASME B16.25;
body-disc-seat AISI 304 Stellite; ASME B16.34 standard;
class 2500.
VR-137 E30 Check valve; horizontal; globo type; bolted bonnet; chamfer
piston disc; ring type joint (RTJ); finishing as MSS SP-6; body-
disc-seat ASTM A 216 Gr WCB with ASTM B564 (UNS
N06625); API 594 standard; class 600.
VR-139 B30 C30 Check valve; horizontal; globe type; bolted bonnet; socket
weld end; finishing as MSS SP-6; body-disc-seat ASTM B564
(UNS N06625); API 594 standard; class 800.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 92 of 94
VR-140 C30 Check valve; wafer; dual plate type; raised face (RF); finishing
as MSS SP-6; body-disc-stem ASTM A 216 Gr WCB with
UNS N06625; Viton seat TBR-S; spring Inconel®; ISO 14313
(API 6D) standard; class 300.
VR-141 H30 H38 Check valve; wafer; dual plate type; carbon steel with ASTM
B564 (UNS N06625); metallic seal joint (MSJ); finishing as
NORSOK L-005; body-disc-stem ASTM A 216 Gr WCB with
coated ASTM B564 (UNS N06625); spring Inconel®; Viton
seat TBR-S; class 2500.
VR-142 J5 Check valve; wafer; dual plate type; carbon steel; bolted
bonnet; metallic seal joint (MSJ); finishing as NORSOK L-
005; body-disc-stem ASTM A 487 Gr 9N; ISO 10423 (API
SPEC 6A) standard; rated working pressure 10000 psi.
VR-143 J31 Check valve; swing type; full opening; alloy steel; bolted
bonnet; compact flanged NORSOK L-005; metallic seal joint
(MSJ); body-disc-seat ASTM A 522 type I; ISO 10423 (API
SPEC 6A) standard; rated working pressure 10000 psi.
VR-147 B22 B23 Check valve; horizontal; globe type; carbon steel; bolted
B24 bonnet; chamfer piston disc; flanged ends ASME B16.5; flat
face (FF); body ASTM A ; disc-seat AISI 410-Stellite®; body-
trim organic coated; ISO 15761 standard; class 150.
VR-148 B14 B22 Check valve; wafer; dual plate; globe type; carbon steel;
B23 B24 bolted bonnet; chamfer piston disc; flat face (FF); finishing
as MSS SP-6; body ASTM A 105; body-trim organic coated;
disc-seat AISI 316; API 594 standard; class 150.
VR-148A B14 B22 Check valve; wafer; horizontal; globe type; carbon steel;
B23 bolted bonnet; chamfer piston disc; flat face (FF) ASME
B16.47 Series A; finishing as MSS SP-6; body ASTM A 216
Gr WCB; body-trim organic coated; disc-seat AISI 316; API
594 standard; class 150.
VR-149 B9 B10 B15 Check valve; wafer; dual plate type; carbon steel; raised face
(RF); finishing as MSS SP-6; body-disc ASTM A 216 Gr
WCB; spring Inconel®; stem AISI 410; body-trim organic
coated; API 594 standard; class 150.
VR-149A B9 B10 B15 Check valve; wafer; dual plate type; carbon steel; raised face
(RF) ASME B16.47 Series A; finishing as MSS SP-6; body-
disc ASTM A 216 Gr WCB; spring Inconel®; stem AISI 410;
body-trim organic coated; API 594 standard; class 150.
VR-150 B9 B10 B15 Check valve; horizontal; globe type; carbon steel; bolted
bonnet; chamfer piston disc; socket weld ends MSS SP-84;
body ASTM A 105; disc-seat AISI 410; ISO 15761 (BS 5352)
standard; class 800.
VR-151 E30 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
finishing as MSS SP-6; body-disc-seat ASTM A 216 Gr WCB
with Inconel® 625; API 594 standard; class 600.
VR-152 F16 Check valve; wafer; dual plate type; stainless steel duplex;
ring type joint (RTJ); finishing as MSS SP-6; body-disc-stem
ASTM A 995 Gr 4A (UNS J92205); Viton seat TBR-S; spring
Inconel®; API 594 standard; class 900.
VR-154 H6 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 352 Gr
LCB; spring Inconel®; stem AISI 304; Viton seat; API 594
standard; class 2500.
VR-155 E32 Check valve; horizontal; globo type; bolted bonnet; chamfer
piston disc; ring type joint (RTJ); finishing as MSS SP-6;
body-disc-seat ASTM B564 (UNS N06625); API 594
standard; class 800.
VR-156 E32 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6– Piping Standard and Material for Oil Production and Process Facilities PAGE: 94 of 94
VR-157 F32 F33 Check valve; wafer type; dual plate type; Inconel® 625 alloy
steel; bolted bonnet; ring type joint (RTJ); finishing as MSS
SP-6; body-disc-seat ASTM B 564 (UNS N06625); API 594
standard; class 1500.
VR-158 F32 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
finishing as MSS SP-6; body-disc-seat ASTM A 350 Gr LF3
with coated ASTM B 564 (UNS N06625); API 594 standard;
class 1500.
VR-159 F32 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
finishing as MSS SP-6; body-disc-seat ASTM A 350 Gr LF3
with coated ASTM B 564 (UNS N06625); API 594 standard;
class 900.
VR-160 F33 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
finishing as MSS SP-6; body-disc-seat ASTM A 350 Gr LF2
with coated ASTM B 564 (UNS N06625); API 594 standard;
class 1500.
VR-161 F33 Check valve; wafer type; dual plate type; Carbon steel with
Inconel® 625 alloy steel; bolted bonnet; ring type joint (RTJ);
finishing as MSS SP-6; body-disc-seat ASTM A 350 Gr LF2
with coated ASTM B 564 (UNS N06625); API 594 standard;
class 900.
VR-162 H33 Check valve; wafer; dual plate type; carbon steel; ring type
joint (RTJ); finishing as MSS SP-6; body-disc ASTM A 350 Gr
LF2 with coated ASTM B564 (UNS N06625); spring
Inconel®; stem AISI 304; Viton seat; API 594 standard; class
2500.
VR-163 J40 Check valve; swing type; full opening; alloy steel; bolted
bonnet; compact flanged NORSOK L-005; metallic seal joint
(MSJ); body-disc-seat ASTM B564 (UNS N06625); ISO
10423 (API SPEC 6A) standard; rated working pressure
10000 psi.
BRE-01 A4 Bushing; pipe line; hex head; carbon steel; ASTM A 105;
ASME B16.11 standard; threaded ends ASME B1.20.1
NPT.
BRE-05 B20 Bushing; pipe line; hex head; PVC poly vinyl chloride; ASTM
D 1784 class 12454; dimensions ASTM D 2464; socket
weld ends.
BRE-06 B21 Bushing; pipe line; hex head; CPVC chlorinated polyvinyl
chloride; ASTM D 1784 class 23447; dimensions ASTM F
437; socket weld ends.
BRE-91 B7 B7R Bushing; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.11; 20 bar pressure; capillary male x
threaded female ends ASME B1.20.1 NPT.
BUJ-01 A4 Plug; pipe line; hex head; carbon steel; ASTM A 105; ASME
B16.11 standard; class 3000; threaded ends ASME
B1.20.1.NPT.
BUJ-07 B20 Plug; pipe line; short type; PVC poly vinyl chloride; ASTM D
1784 class 12454; dimensions ASTM D 2464; thread ends
ASME B1.20.1 NPT.
BUJ-08 B21 Plug; pipe line; short type; CPVC chlorinated polyvinyl
chloride; ASTM D 1784 class 23447; dimensions ASTM F
437; thread ends ASME B1.20.1 NPT.
BUJ-09 B22 B23 B24 Plug; pipe line; hex head; stainless steel; ASTM A 182 Gr
F316; ASME B16.11 standard; class 3000; threaded ends
ASME B1.20.1 NPT.
BUJ-91 B7 B7R Plug; pipe line; hex head; Cu-Ni 90/10 (UNS C70620);
EEMUA 146 standard; ASME B16.11; 20 bar pressure;
threaded ends ASME B1.20.1 NPT.
C453D-04 G16P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S31803); 45 degress; radius 3 x NPS; buttweld ends
ASME B16.25; piggable.
C453D-06 G10P H10P Elbow; pipe line; carbon steel; API 5L Gr X65 PSL 1; 45
H30P degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable
C453D-06B H10P Elbow; pipe line; carbon steel; API 5L Gr X65 PSL 1; 45
degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C453D-07 J31P Elbow; pipe line; carbon steel; ASTM A 333 Gr 8 seamless;
45 degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C453D-08 H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 45
degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable
C453D-08B H38P Elbow; pipe line; carbon steel; API 5L Gr Gr X80 PSL 2; 45
degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C455D-03 G12P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S32760) seamless; 45 degress; radius 5 x NPS;
buttweld ends ASME B16.25; piggable.
C455D-04 G16P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S31803); 45 degress; radius 5 x NPS; buttweld ends
ASME B16.25; piggable.
C455D-06 G10P H10P Elbow; pipe line; carbon steel; API 5L Gr X65 PSL 1; 45
H30P degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C455D-06B G10P H10P Elbow; pipe line; carbon steel; API 5L Gr X65 PSL 1; 45
H30P degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C455D-07 J31P Elbow; pipe line; carbon steel; ASTM A 333 Gr 8 seamless;
45 degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C455D-08 H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 45
degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C455D-08B H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 45
degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C903D-03 G12P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S32760) seamless; 90 degrees; radius 3 x NPS;
buttweld ends ASME B16.25; piggable.
C903D-04 G16P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S31803); 90 degress; radius 3 x NPS; buttweld ends
ASME B16.25; piggable.
C903D-06 G10P H10P Elbow; pipe line; carbon steel; API 5L Gr X65 PSL 1; 90
H30P degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C903D-07 J31P Elbow; pipe line; carbon steel; ASTM A 333 Gr 8 seamless;
90 degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C903D-08 H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 90
degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C903D-08B H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 90
degrees; radius 3 x NPS; buttweld ends ASME B16.25;
piggable.
C905D-03 G12P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S32760) seamless; 90 degress; radius 5 x NPS;
buttweld ends ASME B16.25; piggable.
C905D-04 G16P Elbow; pipe line; stainless steel superduplex; ASTM A 790
(UNS S31803); 90 degress; radius 5 x NPS; buttweld ends
ASME B16.25; piggable.
C905D-06 H10P H30P Elbow; pipe line; carbon steel; API 5L Gr X 65 PSL 1; 90
degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C905D-06B G10P H10P Elbow; pipe line; carbon steel; API 5L Gr X 65 PSL 1; 90
H30P degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C905D-07 J31P Elbow; pipe line; carbon steel; ASTM A 333 Gr 8 seamless;
90 degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C905D-08 H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 90
degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
C905D-08B H38P Elbow; pipe line; carbon steel; API 5L Gr X80 PSL 2; 90
degrees; radius 5 x NPS; buttweld ends ASME B16.25;
piggable.
CONF-91 B7 B7R Female connector; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146; 20 bar pressure; threaded female end ASME
B1.20.1 NPT x capillary female end.
CONM-91 B7 B7R Male connector; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146; 20 bar pressure; threaded male end ASME
B1.20.1 NPT x capillary female end.
CRC-01 A4 A8 B4 B5 Elbow; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; 90 degrees; short radius; buttweld ends
B14 B15 C4 ASME B16.25.
C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E17 E30
F4 F5 F10
F10R F11F14
G4 G5 G10
G10R G11
G14 G18 H5
H10 H11
CRC-02 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL6;
E6 E6R F6 ASME B16.9 standard; 90 degrees; short radius; buttweld
F6R G6 G6R ends ASME B16.25.
H6
CRC-05 B13 C13 Elbow; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; 90 degrees; short
radius; buttweld ends ASME B16.25.
CRC-06 B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; 90 degrees; short
radius; buttweld ends ASME B16.25.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 5 of 72
CRC-07 B15 Elbow; pipe line; carbon steel; Mariloy (S400/TPY); welded
(JIS G 3454/57); 90 degrees; short radius; buttweld ends
ASME B16.25.
CRC-08 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 90
degrees; short radius; rigid joint ends / butt-strap (JR/PP).
CRC-09 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 45
degrees; short radius; rigid joint ends / butt-strap (JR/PP).
CRC-13 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 45
degrees; short radius; rigid joint ends / flange-flange
(JR/FF).
CRC-14 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 22º 30`
degrees; short radius; rigid joint ends / butt-strap (JR/PP).
CRC-16 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 22º 30`
degrees; short radius; rigid joint ends / flange-flange
(JR/FF).
CRC-17 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 11º 15`
degrees; short radius; rigid joint ends / butt-strap (JR/PP).
CRC-19 B25 Elbow; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5 standard; 11º 15`
degrees; short radius; rigid joint ends / flange-flange
(JR/FF).
CRC-20 G11 G14 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 60; ASME
B16.9 standard; 90 degrees; short radius; buttweld ends
ASME B16.25.
CRC-21 G18 H11 J5 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 70; ASME
B16.9 standard; 90 degrees; short radius; buttweld ends
ASME B16.25.
CRC-22 B16 C16 E16 90 degrees elbow, pipe line; duplex stainless steel; ASTM A
F16 G16 815 (UNS S31803); ASME B16.9 standard; short radius;
buttweld ends ASME B16.25.
CRC-23 J31 90 degrees elbow; pipe line; carbon steel; ASTM A 420 Gr
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 6 of 72
CRC-26 G10 H10 H14 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 65; ASME
H30 B16.9 standard; 90 degrees; short radius; buttweld ends
ASME B16.25.
CRC-28 E32 F32 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL3;
ASME B16.9 standard; 90 degrees; short radius; buttweld
ends ASME B16.25.
CRC-29 H38 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 80; ASME
B16.9 standard; 90 degrees; short radius; buttweld ends
ASME B16.25.
CRC-30 J40 Elbow; pipe line; carbon steel; ASTM B564 (UNS N06625);
ASME B16.9 standard; 90 degrees; short radius; buttweld
ends ASME B16.25.
CRL-01 A4 A8 B4 B5 Elbow; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; 90 degrees; long radius; buttweld ends
B14 B15 B17 ASME B16.25.
C4 C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E17 E30
F4 F5 F10
F10R F11
F14 G4 G5
G10 G10R
G11 G14
G18 H5 H10
H11
CRL-02 A4 A8 B4 B5 Elbow; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; 45 degrees; long radius; buttweld ends
B14 B15 C4 ASME B16.25.
C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E11 E10R
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 7 of 72
CRL-03 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL6;
E6 E6R F6 ASME B16.9 standard; 90 degrees; long radius; buttweld
F6R G6 G6R ends ASME B16.25.
G19 H6
CRL-04 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL6;
E6 E6R F6 ASME B16.9 standard; 45 degrees; long radius; buttweld
F6R G6 G6R ends ASME B16.25.
H6
CRL-09 G11 G14 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 60; ASME
G18 B16.9 standard; 90 degrees; long radius; buttweld ends
ASME B16.25.
CRL-10 G11 G14 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 60; ASME
G18 B16.9 standard; 45 degrees; long radius; buttweld ends
ASME B16.25.
CRL-11 B13 C13 Elbow; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; 90 degrees; long
radius; buttweld ends ASME B16.25.
CRL-12 B13 C13 Elbow; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; 45 degrees; long
radius; buttweld ends ASME B16.25.
CRL-13 B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; 90 degrees; long
radius; buttweld ends ASME B16.25.
CRL-14 B12 C12 G12 Elbow; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; 45 degrees; long
radius; buttweld ends ASME B16.25.
CRL-15 B22 B23 Elbow; pipe line; FRP; ASTM F 1173-01; resin according
manufacturer, with external layer, of improved resin with
ultraviolet inhibitor; 90 degrees; long radius; butt and strap
joint ends.
CRL-16 B24 Elbow; pipe line; FRP; ASTM F 1173-01; fenolic resin, with
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 8 of 72
CRL-17 B22 B23 Elbow; pipe line; FRP; ASTM F 1173-01; resin according
manufacturer with external layer, of improved resin with
ultraviolet inhibitor; 45 degrees; long radius; butt and strap
joint ends.
CRL-18 B24 Elbow; pipe line; FRP; ASTM F 1173-01; fenolic resin; with
external layer of improved resin with ultraviolet inhibitor; 45
degrees; long radius; butt and strap joint ends.
CRL-19 B15 Elbow; pipe line; carbon steel Mariloy (S400/TPY); welded
(JIS G 3454/57); 90 degrees; long radius; buttweld ends
ASME B16.25.
CRL-20 H11 J5 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 70; ASME
B16.9 standard; 90 degrees; long radius; buttweld ends
ASME B16.25.
CRL-21 H11 J5 Elbow; pipe line; carbon steel; ASTM A 694 Gr F 70; ASME
B16.9 standard; 45 degrees; long radius; buttweld ends
ASME B16.25.
CRL-30 B16 C16 E16 90 degrees elbow, pipe line; duplex stainless steel; ASTM A
F16 G16 815 (UNS S31803); ASME B16.9 standard; long radius;
buttweld ends ASME B16.25.
CRL-31 B16 C16 E16 45 degrees elbow, pipe line; duplex stainless steel; ASTM A
F16 G16 815 (UNS S31803); ASME B16.9 standard; long radius;
buttweld ends ASME B16.25.
CRL-32 J31 90 degrees elbow; pipe line; alloy steel; ASTM A 420 Gr
WPL8; ASME B16.9 standard; 90 degrees; long radius;
buttweld ends ASME B16.25.
CRL-33 J31 45 degrees elbow; pipe line; alloy steel; ASTM A 420 Gr
WPL8; ASME B16.9 standard; 90 degrees; long radius;
buttweld ends ASME B16.25.
CRL-39 G10 H10 H14 Elbow; pipe line; carbon steel; ASTM A 694 Gr F65; ASME
H30 B16.9 standard; 90 degrees; long radius; buttweld ends
ASME B16.25.
CRL-42 E32 F32 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL3;
ASME B16.9 standard; 90 degrees; long radius; buttweld
ends ASME B16.25.
CRL-43 E32 F32 Elbow; pipe line; carbon steel; ASTM A 420 Gr WPL3;
ASME B16.9 standard; 45 degrees; long radius; buttweld
ends ASME B16.25.
CRL-44 H38 Elbow; pipe line; carbon steel; ASTM A 694 Gr F80; ASME
B16.9 standard; 90 degrees; long radius; buttweld ends
ASME B16.25.
CRL-45 H38 Elbow; pipe line; carbon steel; ASTM A 694 Gr F80; ASME
B16.9 standard; 45 degrees; long radius; buttweld ends
ASME B16.25.
CRL-46 J40 Elbow; pipe line; carbon steel; ASTM B564 (UNS N06625);
ASME B16.9 standard; 90 degrees; long radius; buttweld
ends ASME B16.25.
CRL-47 J40 Elbow; pipe line; carbon steel; ASTM B564 (UNS N06625);
ASME B16.9 standard; 45 degrees; long radius; buttweld
ends ASME B16.25.
CRL-92 B7 B7R Elbow; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 90 degrees; long radius; 20 bar
pressure; buttweld ends ASME B16.25.
CRL-93 B7 B7R Elbow; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 45 degrees; long radius; 20 bar
pressure; buttweld ends ASME B16.25.
CRL-94 B7R Elbow; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 90 degrees; long radius; 16 bar
pressure; buttweld ends ASME B16.25.
CRL-95 B7R Elbow; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 45 degrees; long radius; 16 bar
pressure; buttweld ends ASME B16.25.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 10 of 72
CRUZ-02 A4 A8 B4 B5 Cross; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; buttweld ends ASME B16.25.
B14 B15 B17
C4 C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E17 E30
F4 F5 F10
F10R F11
F14 G4 G5
G10 G10R
G11 G14
G18 H5 H10
H11
CRUZ-05 A8 B4 B9 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
CRUZ-06 B9 B10 B11 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F11 F14 G4
G10 G10R
G10P G11
G14 G18
CRUZ-08 B6 B19 C6 Cross; pipe line; carbon steel; ASTM A 420 Gr WPL6;
E6 E6R F6 ASME B16.9 standard; buttweld ends ASME B16.25.
F6R G6 G6R
G19 H6
CRUZ-09 B6 B19 C6 Cross; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 3000; socket weld ends.
CRUZ-12 B6 B19 C6 Cross; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
CRUZ-17 B13 C13 Cross; pipe line; stainless steel; ASTM A 182 Gr F 53 (UNS
S32750); ASME B16.11 standard; class 3000; socket weld
ends.
CRUZ-18 B12 C12 Cross; pipe line; stainless steel; ASTM A 182 Gr F 55 (UNS
S32760); ASME B16.11 standard; class 3000; socket weld
ends.
CRUZ-20 B13 C13 Cross; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; buttweld ends
ASME B16.25.
CRUZ-21 B12 C12 G12 Cross; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; buttweld ends
ASME B16.25.
CRUZ-22 B25 Cross; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5; rigid joint ends /
butt-strap (JR/PP).
CRUZ-24 B25 Cross; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; ASME B16.5; rigid joint ends /
flange-flange (JR/FF).
CRUZ-25 G11 G14 Cross; pipe line; carbon steel; ASTM A 694 Gr F60; ASME
G18 B16.9 standard; buttweld ends ASME B16.25.
CRUZ-26 G12 G12P Cross; pipe line; stainless steel; ASTM A 182 Gr F55 (UNS
S32760); ASME B16.11 standard; class 6000; socket weld
ends.
CRUZ-27 G10 H10 H14 Cross; pipe line; stainless steel; ASTM A 694 Gr F65; ASME
H30 B16.9 standard; buttweld ends.
CRUZ-28 B17 E17 H11 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; class 9000; socket weld ends.
CRUZ-29 J12 Cross; pipe line; stainless steel; ASTM A 182 Gr F 55 (UNS
S32760); ASME B16.11 standard; class 9000; socket weld
ends.
CRUZ-32 B16 C16 E16 Cross; pipe line; duplex stainless steel; ASTM A 182 Gr F
F16 G16 51 (UNS S31803); ASME B16.11 standard; class 3000;
G16P socket weld ends.
CRUZ-33 B16 C16 E16 Cross; pipe line; duplex stainless steel; ASTM A 815 (UNS
F16 G16 S31803); ASME B16.9 standard; buttweld ends ASME
B16.25.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 12 of 72
CRUZ-34 E30 H10 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.9
H10P H11 standard; buttweld ends ASME B16.25.
CRUZ-35 J31 J31P Cross; pipe line; alloy steel; ASTM A 420 Gr WPL8; ASME
B16.9 standard; buttweld ends ASME B16.25
CRUZ-42 G19 Cross; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.11 standard; class 9000; socket weld ends.
CRUZ-43 A4 Cross; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; class 2000; thread ends ASME B1.20.1 NPT.
CRUZ-44 B30 C30 E30 Cross; pipe line; ASTM B564 (UNS N06625); ASME B16.9
E32 F32 standard; class 3000; socket weld ends ASME B16.25.
CRUZ-45 H30 H30P Cross; pipe line; ASTM B564 (UNS N06625); ASME B16.9
H38 H38P standard; buttweld ends ASME B16.25.
J40
CRUZ-46 H6 Cross; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.9 standard; buttweld ends ASME B16.25.
CRUZ-47 H11 J5 Cross; pipe line; stainless steel; ASTM A 694 Gr F70; ASME
B16.9 standard; buttweld ends.
CRUZ-48 E32 F32 Cross; pipe line; stainless steel; ASTM A 420 Gr WPL3;
ASME B16.9 standard; buttweld ends.
CRUZ-50 H38 Cross; pipe line; stainless steel; ASTM A 694 Gr F80; ASME
B16.9 standard; buttweld ends.
CRUZR-01 B25 Reducing cross; pipe line; RPVC-PVC coated external with
fiber glass, thermosetting resin; ASME B16.5; rigid joint
ends / butt-strap (JR/PP).
CRUZR-03 B25 Reducing cross; pipe line; RPVC-PVC coated external with
fiber glass, thermosetting resin; ASME B16.5; rigid joint
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 13 of 72
FLG-02A A4 B14 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.5 standard; full face (FF); serrated finishing 125 µin –
250 µin; class 150.
FLG-02B B14 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; full face (FF); serrated finishing
125 µin – 250 µin; class 150.
FLG-03A B15 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.5 standard; raised face (RF); serrated finishing 125 µin
– 250 µin; class 150.
FLG-03B B15 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150.
FLG-04A B4 B5 B9 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
B10 B11 B15 ASME B16.5 standard; raised face (RF); serrated finishing
B17 125 µin – 250 µin; class 150.
FLG-04B A4 A8 B5 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
B14 ASME B16.5 standard; full face (FF); serrated finishing 125
µin – 250 µin; class 150.
FLG-04C B9 B10 B11 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.47 Series A standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150.
FLG-04D B14 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.47 Series A standard; full face (FF); serrated
finishing 125 µin – 250 µin; class 150.
FLG-05A B4 B5 B7 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B7R B9 B10 B16.5 standard; raised face (RF); serrated finishing 125 µin
B11 B15 B17 – 250 µin; class 150.
FLG-05B A4 A8 B5 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B14 B16.5 standard; full face (FF); serrated finishing 125 µin –
250 µin; class 150.
FLG-05C B7 B7R B9 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B10 B11 B15 B16.47 Series A standard; raised face (RF); serrated
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 14 of 72
FLG-05D B14 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; full face (FF); serrated finishing
125 µin – 250 µin; class 150.
FLG-05E B4 B9 B10 Flange; pipe line; socket welding; carbon steel; ASTM A
B17 105; ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150;
A8 – For pipe NPS ½ " - 1 ½” – Sch 80.
B4 – For pipe NPS ½ " - 1 ½” – Sch 80.
B9 – For pipe NPS ½ " - ¾” – XXS.
B9 – For pipe NPS 1" - 1 ½” – Sch 80.
B10 – For pipe NPS ½ " - ¾” – Sch 160.
B10 – For pipe NPS 1" - 1 ½” – Sch 80.
B11 – For pipe NPS ½ " - ¾” – Sch 160.
B11 – For pipe NPS 1" - 1 ½” – Sch 80.
FLG-09C C14 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.5 standard; full face (FF); serrated finishing 125 µin –
250 µin; class 300.
FLG-09D C14 Flange; pipe line; slip-on; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; full face (FF); serrated finishing
125 µin – 250 µin; class 300.
FLG-10A C4 C5 C8 C9 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
C10 C11 C30 ASME B16.5 standard; raised face (RF); serrated finishing
125 µin – 250 µin; class 300.
FLG-10B C14 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.5 standard; full face (FF); serrated finishing 125
µin – 250 µin; class 300.
FLG-10C C9 C30 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.47 Series A standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-10D C14 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.47 Series A standard; full face (FF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-11A C4 C8 C9 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
C10 C11 C30 B16.5 standard; raised face (RF); serrated finishing 125 µin
– 250 µin; class 300.
FLG-11B C14 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B16.5 standard; full face (FF); serrated finishing 125 µin –
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 15 of 72
FLG-11C C9 C30 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-11D C14 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
B16.47 Series A standard; full face (FF); serrated finishing
125 µin – 250 µin; class 300.
FLG-13 B5 C5 E4 E5 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
E8 E9 E10 ASME B16.5 standard; ring type joint (RTJ); surface finish
E10R E11 not exceed 63 µin; class 600.
E14 E17
FLG-15 B5 E4 E5 E8 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
E9 E10 E10R B16.5 standard; ring type joint (RTJ); surface finish not
E11 E14 exceed 63 µin; class 600.
FLG-16 F4 F5 F10 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
F10R F11 ASME B16.5 standard; ring type joint (RTJ); surface finish
F14 not exceed 63 µin; class 900.
FLG-17 F4 F5 F10 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
F10R F11 B16.5 standard; ring type joint (RTJ); surface finish not
F14 exceed 63 µin; class 900.
FLG-18 F4 F5 F10 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
F10R F11 ASME B16.5 standard; ring type joint (RTJ); surface finish
F14 G4 G5 not exceed 63 µin; class 1500.
G10 G10R
G11 G14
G18
FLG-19 F4 F5 F10 Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
F10R F11 B16.5 standard; ring type joint (RTJ); surface finish not
F14 G4 G5 exceed 63 µin; class 1500.
G10 G10R
G10P G11
G14
FLG-20 H5 H10 H11 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
J5 ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 2500.
FLG-21 H5 H10 H10P Flange; pipe line; blind; carbon steel; ASTM A 105; ASME
H11 J5 B16.5 standard; ring type joint (RTJ); surface finish not
exceed 63 µin; class 2500.
FLG-22A B6 B19 Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; raised face (RF);
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 16 of 72
FLG-22B B6 B19 Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.47 Series A standard; raised face
(RF); serrated finishing 125 µin – 250 µin; class 150.
FLG-23A B6 B19 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150.
FLG-23B B6 B19 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.47 Series A standard; raised face (RF);
serrated finishing 125 µin – 250 µin; class 150.
FLG-24 C6 Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; raised face (RF);
serrated finishing 125 µin – 250 µin; class 300.
FLG-25 C6 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-26 E6 E6R Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 600.
FLG-27 E6 E6R Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 600.
FLG-32 F6 F6R Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 900.
FLG-33 F6 F6R Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 900.
FLG-34 F6 F6R G6 Flange; pipe line; welding neck; carbon steel; ASTM A 350
G6R G19 Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 1500.
FLG-35 F6 F6R G6 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
G6R G19 CL1; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 1500.
FLG-41A C4 C9 C10 Flange; pipe line; socket welding; carbon steel; ASTM A
105; ASME B16.5 standard; raised face (RF); serrated
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 17 of 72
FLG-41B C14 Flange; pipe line; socket welding; carbon steel; ASTM A
105; ASME B16.5 standard; full face (FF); serrated finishing
125 µin – 250 µin; class 300;
C14 – For pipe NPS 1" - 1 ½” – Sch 80.
FLG-42 E4 E9 E10 Flange; pipe line; socket welding; carbon steel; ASTM A
E10R E17 105; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 600;
E4 – For pipe NPS ½” - 1 ½” – Sch 80.
E9 – For pipe NPS ½” - 1 ½” – XXS.
E10 – For pipe NPS ½” - ¾” – Sch 160.
E10 – For pipe NPS 1” - 1 ½” – Sch 80.
E10R – For pipe NPS ½” - 1 ½” – Sch 80.
FLG-43 F4 F10 F10R Flange; pipe line; socket welding; carbon steel; ASTM A
G4 G10 105; ASME B16.5 standard; ring type joint (RTJ); surface
G10R G10P finish not exceed 63 µin; class 1500;
G18 F4 – For pipe NPS ½” - ¾” – Sch 160.
F4 – For pipe NPS 1” - 1 ½” – Sch 80.
F10 – For pipe NPS ½” - ¾” – Sch 160.
F10 – For pipe NPS 1” - 1 ½” – Sch 80.
F10R – For pipe NPS ½” - ¾” – Sch 160.
F10R – For pipe NPS 1” - 1 ½” – Sch 80.
F14 – For pipe NPS 1” - 1 ½” – Sch 80.
G4 – For pipe NPS ½” - 1 ½” – XXS.
G10 – For pipe NPS ½” - 1 ½” – XXS.
G10R – For pipe NPS ½” - 1 ½” – XXS.
G10P – For pipe NPS ½” - 1 ½” – XXS.
G14 – For pipe NPS ½” - 1 ½” – XXS.
FLG-45 B6 B19 Flange; pipe line; socket welding; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; raised face (RF);
serrated finishing 125 µin – 250 µin; class 150;
B6 – For pipe NPS ½” - ¾” – Sch 160.
B6 – For pipe NPS 1” - 1 ½” – Sch 80.
FLG-46 C6 Flange; pipe line; socket welding; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; raised face (RF);
serrated finishing 125 µin – 250 µin; class 300;
C6 – For pipe NPS ½” - ¾” – Sch 160.
C6 – For pipe NPS 1” - 1 ½” – Sch 80.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 18 of 72
FLG-47 E6 E6R Flange; pipe line; socket welding; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 600;
E6 – For pipe NPS ½” - ¾” – Sch 160.
E6R – For pipe NPS 1” - 1 ½” – Sch 80.
FLG-48 F6 F6R G6 Flange; pipe line; socket welding; carbon steel; ASTM A 350
G6R G19 Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 1500;
F6 – For pipe NPS ½” - ¾” – Sch 160.
F6 – For pipe NPS 1” - 1 ½” – Sch 80.
F6R – For pipe NPS ½” - ¾” – Sch 160.
F6R – For pipe NPS 1” - 1 ½” – Sch 80.
G6 – For pipe NPS ½” - 1 ½” – XXS.
G6R – For pipe NPS ½” - 1 ½” – XXS.
FLG-66 B13 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F53 (UNS S32750); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin; class
150.
FLG-67 B13 Flange; pipe line; blind; stainless steel superduplex; ASTM
A 182 Gr F 53 (UNS S32750); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin;
class 150.
FLG-69 B12 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.5
standard; raised face (RF); serrated finishing 125 µin – 250
µin; class 150.
FLG-69A B12 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.47 Series
A standard; raised face (RF); serrated finishing 125 µin –
250 µin; class 150.
FLG-70 B12 Flange; pipe line; blind; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin; class
150.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 19 of 72
FLG-70A B12 Flange; pipe line; blind; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.47 Series A
standard; raised face (RF); serrated finishing 125 µin – 250
µin; class 150.
FLG-72 G11 G14 Flange; pipe line; welding neck; carbon steel; ASTM A 694
Gr F60; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 1500.
FLG-73 G11 G14 Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F60;
ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 1500.
FLG-74 B20 Flange; pipe line; blind; PVC poly vinyl chloride; ASTM D
1784 class 12454; drilling accordant ASME B16.5 standard;
full face (FF); class 150.
FLG-75 B20 Flange; pipe line; socket welding; PVC poly vinyl chloride;
ASTM D 1784 class 12454; drilling accordant ASME B16.5
standard; full face (FF); class 150;
B20 – For pipe NPS ½” - 1 ½” – Sch 80.
FLG-77 B21 Flange; pipe line; blind; CPVC chlorinated polyvinyl chloride;
ASTM D 1784 class 23447; drilling accordant ASME B16.5
standard; full face (FF); class 150.
FLG-83 B22 B23 Flange; pipe line; welding neck; FRP; ASTM D 4024-00-
RTR; (Thermosetting resin reinforced fiber); full face (FF);
class 150.
a–1 (filament wound).
b–Resin according manufacturer approval Classification
Society, with external layer of improved resin with ultraviolet
inhibitor.
c–Fabrication accordant manufacturer approval
Classification Society.
FLG-85 B22 B23 Flange; pipe line; blind; FRP; ASTM D 4024-00-RTR
(Thermosetting resin reinforced fiber; full face (FF); class 16
Bar.
a–1 (filament wound).
b–Resin according manufacturer approval Classification
Society, with external layer of improved resin with ultraviolet
inhibitor.
c–Fabrication accordant manufacturer approval
Classification Society.
FLG-86 B24 Flange; pipe line; welding neck; FRP; ASTM D 4024-00-
RTR (Thermosetting resin reinforced fiber); full face (FF);
class 150.
a–1 (filament wound).
b–Phenolic resin, with external layer of improved resin with
ultraviolet inhibitor.
c–Fabrication accordant manufacturer approval
Classification Society.
FLG-89 H10 Flange; pipe line; welding neck; carbon steel; ASTM A 694
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 21 of 72
FLG-90 B7 B7R Flange; pipe line; slip-on; stub ends; Cu-Ni 90/10 (UNS
C70620); 20 bar pressure; EEMUA 145 standard; ASME
B16.5; raised face (RF); serrated finishing 125 µin – 250 µin.
FLG-94A B7R Flange; pipe line; welding neck; stub ends; Cu-Ni 90/10
(UNS C70620); type L; 16 bar pressure; EEMUA 145
standard; raised face (RF); serrated finishing 125 µin – 250
µin.
FLG-100 C13 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 53 (UNS S32750); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin; class
300.
FLG-101 C13 Flange; pipe line; blind; stainless steel superduplex; ASTM
A 182 Gr F 53 (UNS S32750); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin;
class 300.
FLG-103 C12 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.5
standard; raised face (RF); serrated finishing 125 µin – 250
µin; class 300.
FLG-104 C12 Flange; pipe line; blind; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin – 250 µin;
class 300.
FLG-106 H10 Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F60;
ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 2500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 22 of 72
FLG-109 G12 G12P Flange; pipe line; socket welding; stainless steel
superduplex; ASTM A 182 Gr F 55 (UNS S32760); ASME
B16.5 standard; ring type joint (RTJ); surface finish not
exceed 63 µin; class 1500;
G12 – For pipe NPS ½” - 1 ½” – Sch 40S.
FLG-110 G12 G12P Flange; pipe line; blind; stainless steel superduplex; ASTM A
182 Gr F 55 (UNS S32760); ASME B16.5 standard; ring type
joint (RTJ); surface finish not exceed 63 µin; class 1500.
FLG-111 G12 G12P Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.5 standard;
ring type joint (RTJ); surface finish not exceed 63 µin; class
1500.
FLG-112 H11 Flange; pipe line; welding neck; carbon steel; ASTM A 694
Gr F60; ASME B16.47 series A standard; ring type joint
(RTJ); surface finish not exceed 63 µin; class 2500.
FLG-113 H11 Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F60;
ASME B16.47 series A standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 2500.
FLG-115 J12 Flange; pipe line; welding neck; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.5 standard;
ring type joint (RTJ); surface finish see ISO 4287; class API
10000.
FLG-116 J12 Flange; pipe line; blind; stainless steel superduplex; ASTM A
182 Gr F 55 (UNS S32760); ASME B16.5 standard; ring type
joint (RTJ); surface finish see ISO 4287; class API 10000.
FLG-117 G18 Flange; pipe line; welding neck; carbon steel; ASTM A 694
Gr F70; manufacturer standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 1500.
FLG-120 B16 Flange; socket welding, pipe line; duplex stainless steel;
ASTM A 182 Gr F 51 (UNS S31803); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin - 250 µin Ra;
class 150.
FLG-121 B16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
Gr F 51 (UNS S31803); ASME B16.5 standard; raised face
(RF); serrated finishing 125 µin - 250 µin Ra; class 150.
FLG-121A B16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
Gr F 51 (UNS S31803); ASME B16.47 Séries A standard;
raised face (RF); serrated finishing 125 µin - 250 µin Ra;
class 150.
FLG-122 B16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
A 182 Gr F 51 (UNS S31803); ASME B16.5 standard; raised
face (RF); serrated finishing 125 µin - 250 µin Ra; class 150.
FLG-122A B16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
A 182 Gr F 51 (UNS S31803); ASME B16.47 Series A
standard; raised face (RF); serrated finishing 125 µin - 250
µin Ra; class 150.
FLG-123 C16 Flange; socket welding; pipe line; duplex stainless steel;
ASTM A 182 Gr F 51 (UNS S31803); ASME B16.5 standard;
raised face (RF); serrated finishing 125 µin - 250 µin Ra;
class 300.
FLG-124 C16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
Gr F 51 (UNS S31803); ASME B16.5 standard; raised face
(RF); serrated finishing 125 µin - 250 µin Ra; class 300.
FLG-125 C16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
A 182 Gr F 51 (UNS S31803); ASME B16.5 standard; raised
face (RF); serrated finishing 125 µin - 250 µin Ra; class 300.
FLG-126 E16 Flange; socket welding; pipe line; duplex stainless steel;
ASTM A 182 Gr F 51 (UNS S31803); ASME B16.5 standard;
ring type joint (RTJ); surface finish not exceed 63 µin; class
600.
FLG-127 E16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
Gr F 51 (UNS S31803); ASME B16.5 standard; ring type joint
(RTJ); surface finish not exceed 63 µin; class 600.
FLG-128 E16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
A 182 Gr F 51 (UNS S31803); ASME B16.5 standard; ring
type joint (RTJ); surface finish not exceed 63 µin; class 600.
FLG-129 F16 G16 Flange; socket welding; pipe line; duplex stainless steel;
G16P ASTM A 182 Gr F 51 (UNS S31803); ASME B16.5 standard;
ring type joint (RTJ); surface finish not exceed 63 µin; class
1500.
FLG-130 F16 G16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
G16P Gr F 51 (UNS S31803); ASME B16.5 standard; ring type joint
(RTJ); surface finish not exceed 63 µin; class 1500.
FLG-131 F16 G16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
G16P A 182 Gr F 51 (UNS S31803); ASME B16.5 standard; ring
type joint (RTJ); surface finish not exceed 63 µin; class 1500.
FLG-141 H10 H14 H30 Compact flange; pipe line; blind; carbon steel; ASTM A 694
H30P Gr F65; NORSOK L-005 standard; metallic seal joint (MSJ);
surface finish see ISO 4287; class 2500.
FLG-142 H10 H14 H30 Compact Flange; pipe line; welding neck; carbon steel;
H30P ASTM A 694 Gr F65; NORSOK L-005 standard; metallic seal
joint (MSJ); surface finish see ISO 4287; class 2500.
FLG-149 J31 J31P Flange; pipe line; blind; alloy steel; ASTM A 522 type I;
NORSOK L-005 standard; metallic seal joint (MSJ); surface
finish see ISO 4287; API 10000.
FLG-150 J31 J31P Flange; pipe line; welding neck; alloy steel; ASTM A 522 type
I; NORSOK L-005 standard; metallic seal joint (MSJ); surface
finish see ISO 4287; API 10000.
FLG-151 E30 Flange; pipe line; blind carbon steel; ASTM A 105; ASME
B16.5 standard; ring type joint (RTJ); surface finish see ISO
4287; class 600.
FLG-152 E30 Flange; pipe line; welding neck; carbon steel; ASTM A 105;
ASME B16.5 standard; raised face (RF); surface finish see
ISO 4287; class 600.
FLG-153 H10 H14 H30 Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F65;
H30P ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 2500.
FLG-154 H10 H14 H30 Flange; pipe line; welding neck; carbon steel; ASTM A 694
H30P Gr F65; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 2500.
FLG-157 H10P Compact flange; pipe line; welding neck; carbon steel; ASTM
A 694 Gr F65; NORSOK L-005 standard; metallic seal joint
(MSJ); surface finish see ISO 4287; class 2500.
FLG-158 H10P Compact flange; pipe line; blind; carbon steel; ASTM A 694
Gr F65; NORSOK L-005 standard; metallic seal joint (MSJ);
surface finish see ISO 4287; class 2500.
FLG-161 G10 G10P Flange; pipe line; welding neck; carbon steel; ASTM A 694
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 25 of 72
FLG-162 G10 G10P Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F65;
ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 in; class 1500.
FLG-163A B3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150.
FLG-163B B3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.47 Series A standard; raised face
(RF); serrated finishing 125 µin – 250 µin; class 150.
FLG-166 C3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-169 E3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 600.
FLG-172 F3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 900.
FLG-174 F3 G3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 1500.
FLG-178 H3 Flange; pipe line; welding neck; stainless steel; ASTM A 182
Gr F 316L; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 2500.
FLG-179 B30 Flange; pipe line; socket welding; ASTM B564 (UNS
N06625); ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 150;
FLG-180 B30 Flange; pipe line; blind; ASTM B564 (UNS N06625); ASME
B16.5 standard; raised face (RF); serrated finishing 125 µin –
250 µin; class 150;
FLG-181 H30 H30P Flange; pipe line; blind; ASTM B564 (UNS N06625); ASME
H38 H38P B16.5 standard; ring type joint (RTJ); surface finish not
exceed 63 µin; class 2500.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 27 of 72
FLG-182 H30 H30P Flange; pipe line; welding neck; ASTM B 564 (UNS N06625);
H38 H38P ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 2500.
FLG-183 B7 B7R Backing flange; pipe line; carbon steel; ASTM A 105; epoxy
coated; ASME B16.5; class 150.
FLG-184 B7 B7R Flange; pipe line; weld neck; stub ends; Cu-Ni 90/10 (UNS
C70620); type L; 20 bar pressure; EEMUA 145 standard;
raised face (RF); serrated finishing 125 µin – 250 µin.
FLG-185 B7 B7R Backing flange; pipe line; carbon steel; ASTM A 105; epoxy
coated; ASME B16.47 Series A; class 150.
FLG-188 C30 Flange; pipe line; socket welding; ASTM B564 (UNS
N06625); ASME B16.5 standard; raised face (RF); serrated
finishing 125 µin – 250 µin; class 300.
FLG-189 C30 Flange; pipe line; blind; ASTM B564 (UNS N06625); ASME
B16.5 standard; raised face (RF); serrated finishing 125 µin –
250 µin; class 300.
FLG-190 E30 E32 Flange; pipe line; socket welding; ASTM B564 (UNS
N06625); ASME B16.5 standard; ring type joint (RTJ);
serrated finishing 125 µin – 250 µin; class 600.
FLG-191 E30 E32 Flange; pipe line; blind; ASTM B564 (UNS N06625); ASME
B16.5 standard; ring type joint (RTJ); serrated finishing 125
µin – 250 µin; class 600.
FLG-193 F16 Flange; blind, pipe line; duplex stainless steel; ASTM A 182
Gr F 51 (UNS S31803); ASME B16.5 standard; ring type joint
(RTJ); surface finish not exceed 63 µin; class 900.
FLG-194 F16 Flange; welding neck, pipe line; duplex stainless steel; ASTM
A 182 Gr F 51 (UNS S31803); ASME B16.5 standard; ring
type joint (RTJ); surface finish not exceed 63 µin; class 900.
FLG-196 H6 Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF2 CL1; ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 2500.
FLG-197 H6 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 2500.
FLG-198 H11 Compact Flange; pipe line; welding neck; carbon steel;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 28 of 72
FLG-199 H11 Compact flange; pipe line; blind; carbon steel; ASTM A 694
Gr F70; NORSOK L-005 standard; metallic seal joint (MSJ);
surface finish see ISO 4287; class 2500.
FLG-200 E32 Flange; pipe line; blind; carbon steel; ASTM A 350 Gr LF3;
ASME B16.5 standard; ring type joint (RTJ); serrated
finishing 125 µin – 250 µin; class 600.
FLG-201 E32 Flange; pipe line; welding neck; carbon steel; ASTM A 350
Gr LF3 ; ASME B16.5 standard; ring type joint (RTJ);
serrated finishing 125 µin – 250 µin; class 600.
FLG-202 F32 Flange; blind, pipe line; carbon steel; ASTM B564 (UNS
N06625); ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 900.
FLG-203 F32 Flange; socket welding; pipe line; carbon steel; ASTM B564
(UNS N06625); ASME B16.5 standard; ring type joint (RTJ);
surface finish not exceed 63 µin; class 900.
FLG-204 F32 Flange; blind, pipe line; carbon steel; ASTM A 350 Gr LF3;
ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 900.
FLG-205 F32 Flange; welding neck; pipe line; carbon steel; ASTM A 350
Gr LF3; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 900.
FLG-206 J40 Flange; pipe line; blind; alloy steel; ASTM B564 (UNS
N06625); NORSOK L-005 standard; metallic seal joint (MSJ);
surface finish see ISO 4287; API 10000.
FLG-207 J40 Flange; pipe line; welding neck; alloy steel; B564 (UNS
N06625); NORSOK L-005 standard; metallic seal joint (MSJ);
surface finish see ISO 4287; API 10000.
FLG-208 H38 H38P Flange; pipe line; blind; carbon steel; ASTM A 694 Gr F80;
ASME B16.5 standard; ring type joint (RTJ); surface finish
not exceed 63 µin; class 2500.
FLG-209 H38 H38P Flange; pipe line; welding neck; carbon steel; ASTM A 694
Gr F80; ASME B16.5 standard; ring type joint (RTJ); surface
finish not exceed 63 µin; class 2500.
FLG-210 H38 H38P Compact flange; pipe line; blind; carbon steel; ASTM A 694
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 29 of 72
FLG-211 H38 H38P Compact Flange; pipe line; welding neck; carbon steel;
ASTM A 694 Gr F80; NORSOK L-005 standard; metallic seal
joint (MSJ); surface finish see ISO 4287; class 2500.
JO-07 A8 B4 B9 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; 90 degrees; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
JO-08 A8 B4 B9 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; 45 degrees; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
JO-09 B9 B10 B11 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; 90 degrees; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F11 F14 G4
G10 G10R
G10P G11
G14 G18
JO-10 B9 B10 B11 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 C9 C10 standard; 45 degrees; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F11 F14 G4
G10 G10R
G10P G11
G14 G18
JO-13 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; 90 degrees; class 3000; socket
weld ends.
JO-14 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; 45 degrees; class 3000; socket
weld ends.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 30 of 72
JO-17 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; 90 degrees; class 6000; socket
F6R G6 G6R weld ends.
JO-18 B6 B19 C6 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; 45 degrees; class 6000; socket
F6R G6 G6R weld ends.
JO-27 B13 C13 Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 53 (UNS S32750); ASME B16.11 standard; 90
degrees; class 3000; socket weld ends.
JO-28 B13 C13 Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 53 (UNS S32750); ASME B16.11 standard; 45
degrees; class 3000; socket weld ends.
JO-29 B12 C12 Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 55 (UNS S32760); ASME B16.11 standard; 90
degrees; class 3000; socket weld ends.
JO-30 B12 C12 Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 55 (UNS S32760); ASME B16.11 standard; 45
degrees; class 3000; socket weld ends.
JO-31 B20 Elbow; pipe line; PVC poly vinyl chloride; ASTM D 1784
class 12454; dimensions ASTM D 2467; 90 degrees; Sch
80; socket weld ends.
JO-32 B20 Elbow; pipe line; PVC poly vinyl chloride; ASTM D 1784
class 12454; dimensions ASTM D 2467; 45 degrees; Sch
80; socket weld ends.
JO-33 B21 Elbow; pipe line; CPVC chlorinated polyvinyl chloride; ASTM
D 1784 class 23447; dimensions ASTM F 439; 90 degrees;
Sch 80; socket weld ends.
JO-34 B21 Elbow; pipe line; CPVC chlorinated polyvinyl chloride; ASTM
D 1784 class 23447; dimensions ASTM F 439; 45 degrees;
Sch 80; socket weld ends.
JO-35 G12 G12P Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 55 (UNS S32760); ASME B16.11 standard; 90
degrees; class 6000; socket weld ends.
JO-36 G12 G12P Elbow; pipe line; stainless steel superduplex; ASTM A 182
Gr F 55 (UNS S32760); ASME B16.11 standard; 45
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 31 of 72
JO-37 B17 E17 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; 90 degrees; class 9000; socket weld ends.
JO-38 B17 E17 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; 45 degrees; class 9000; socket weld ends.
JO-45 B16 C16 E16 45 degrees elbow, pipe line; duplex stainless steel; ASTM A
F16 G16 182 Gr F 51 (UNS S31803); ASME B16.11 standard; class
G16P 6000; socket weld ends.
JO-46 B16 C16 E16 90 degrees elbow, pipe line; duplex stainless steel; ASTM A
F16 G16 182 Gr F 51 (UNS S31803); ASME B16.11 standard; class
G16P 6000; socket weld ends.
JO-50 G19 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.11 standard; 90 degrees; class 9000; socket
weld ends.
JO-51 G19 Elbow; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.11 standard; 45 degrees; class 9000; socket
weld ends.
JO-52 A4 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; 90 degrees; class 2000; thread ends ASME
B1.20.1 NPT.
JO-53 A4 Elbow; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; 45 degrees; class 2000; thread ends ASME
B1.20.1 NPT.
JO-54 B30 C30 E30 Elbow; pipe line; ASTM B564 (UNS N06625); ASME B16.11
E32 F32 standard; 90 degrees; class 3000; socket weld ends.
JO-55 B30 C30 E30 Elbow; pipe line; ASTM B564 (UNS N06625); ASME B16.11
E32 F32 standard; 45 degrees; class 3000; socket weld ends.
JO-92 B7 B7R Elbow; pipe line; Cu-Ni 90/10; EEMUA 146 standard (UNS
C70620); ASME B16.11; 20 bar pressure; 90 degrees;
capillary female ends.
JO-93 B7 B7R Elbow; pipe line; Cu-Ni 90/10; EEMUA 146 standard (UNS
C70620); ASME B16.11; 20 bar pressure; 45 degrees;
capillary female ends.
JA-01 B5 C5 E4 E5 Ring type joint, flange; oval type R; carbon steel coated Zn-
E8 E9 E10 Ni; max. hardness 90 HB; for flange class 600/900; ASME
E10R E11 B16.20 standard.
E14 E17 F4
F5 F10 F10R
F11 F14
JA-02 F4 F5 F10 Ring type joint, flange; octagonal type; carbon steel coated
F10R F11 Zn-Ni; max. hardness 90 HB; for flange class
F14 G4 G5 1500/2500/API 10000; ASME B16.20 standard.
G10 G10R
G10P G11
G14 G18 H5
H10 H10P
H11 H14 J5
JA-03 E6 E6R F6 Ring type joint, flange; oval type R; stainless steel AISI 304;
F6R max. hardness 150 HB; for flange class 600/900; ASME
B16.20 standard.
JA-04 F6 F6R G6 Ring type joint, flange; octagonal type; stainless steel AISI
G6R G19 304; max. hardness 150 HB; for flange class 1500; ASME
B16.20 standard.
JA-07 F3 F16 G3 Ring type joint, flange; octagonal type; for flange class
H3 G12 1500/2500; stainless steel AISI 316; max. hardness 150 HB;
G12P G16 ASME B16.20 standard.
G16P
JA-08 J12 Ring type joint, flange; octagonal type; for flange class API
10000; stainless steel superduplex; ASTM A 182 Gr F 55
(UNS S32760); ASME B16.20 standard.
JÁ-09 G18 Ring type joint, flange; octagonal type; carbon steel coated
Zn-Ni; max. hardness 90 HB; for flange class 1500/2500;
ASME B16.20 standard.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 33 of 72
JA-10 E16 F16 Ring type joint, flange; octagonal type; for flange class
600/900; stainless steel AISI 316; max. hardness 150 HB;
ASME B16.20 standard.
JA-12 E30 E32 F32 Ring type joint, flange; octagonal type; Inconel® 625; max.
hardness 150 HB; for flange class 600/900; ASME B16.20
standard.
JA-13 H30 H30P Ring type joint, flange; octagonal type; Inconel® 625; max.
H38 H38P hardness 150 HB; for flange class 2500; ASME B16.20
standard.
JA-14 H6 Ring type joint, flange; octagonal type; stainless steel AISI
304; max. hardness 150 HB; for flange class 2500; ASME
B16.20 standard.
JA-15 E3 F3 Ring type joint, flange; octagonal type; stainless steel AISI
316; max. hardness 150 HB; for flange class 600/900;
ASME B16.20 standard.
JE-04 B3 B4 B6 B9 Circular joint, flange; flat ring type; spiral-wound; raised face
B10 B11 B12 (RF) ASME B16.5; semimetallic; stainless steel AISI 304
B16 B17 B19 flexible graphite insert, external centralization ring AISI 304;
ASME B16.20 standard; class 150; wall thickness 0,175”
(4,4 mm).
JE-05 B3 B4 B6 B9 Circular joint, flange; flat ring type; spiral-wound; raised face
B10 B11 B12 (RF) ASME B16.5; semimetallic; stainless steel AISI 304
B16 B17 B19 flexible graphite insert; external and internal centralization
ring AISI 304; ASME B16.20 standard; class 150; wall
thickness 0,175” (4,4 mm).
JE-06 B3 B6 B9 Circular joint, flange; flat ring type; spiral-wound; raised face
B10 B11 B12 (RF) ASME B16.47 Series A standard; semimetallic;
B16 B19 stainless steel AISI 304 flexible graphite insert; external and
internal centralization ring AISI 304; ASME B16.20
standard; class 150; wall thickness 0,175” (4,4 mm).
JE-07 C3 C4 C6 C9 Circular joint, flange; flat ring type; spiral-wound; raised face
C10 C12 C16 (RF) ASME B16.5; semimetallic; stainless steel AISI 304
flexible graphite insert, external centralization ring AISI 304;
ASME B16.20 standard; class 300/600; wall thickness
0,175" (4,4 mm).
JE-08 C3 C4 C6 C9 Circular joint, flange; flat ring type; spiral-wound; raised face
C10 C12 C16 (RF) ASME B16.5; semimetallic; stainless steel AISI 304
flexible graphite insert, external centralization ring AISI 304;
ASME B16.20 standard; class 300; wall thickness 0,175"
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 34 of 72
(4,4 mm).
JE-09 C3 C4 C6 C9 Circular joint, flange; flat ring type; spiral-wound; raised face
C10 C12 C16 (RF) ASME B16.5; semimetallic; stainless steel AISI 304
flexible graphite insert c/ external and internal centralization
ring AISI 304; ASME B16.20 standard; class 300; wall
thickness 0,175” (4,4 mm).
JE-10 C9 Circular joint, flange; flat ring type; spiral-wound; raised face
(RF) ASME B16.47 Series A standard; semimetallic;
stainless steel AISI 304 flexible graphite insert c/ external
and internal centralization ring AISI 304; ASME B16.20
standard; class 300; wall thickness 0,175” (4,4 mm).
JI-01 B3 B7 B7R Circular isolating gasket, for cathodic protection; flange flat
B9 B10 B11 ring, raised face (RF); ASME B16.21 standard; phenolic
B12 B13 B15 resin coated with neoprene; class 150; wall thickness 1/8”
B16 B17 B30 (3,2 mm); polyethylene isolating bushing; phenolic resin
isolating washer and washer carbon steel coated Zn-Ni; for
flange class 150.
JI-03 C9 C10 C12 Circular isolating gasket, for cathodic protection; flange flat
C11 C13 C16 ring, raised face (RF); ASME B16.21 standard; phenolic
C30 resin coated with neoprene; class 300; wall thickness 1/8”
(3,2 mm); polyethylene isolating bushing; phenolic resin
isolating washer and washer carbon steel coated Zn-Ni; for
flange class 300.
JI-04 E3 E6 E6R Circular isolating gasket, for cathodic protection; flange; oval
E9 E10 E10R type R; ring type joint (RTJ); ASME B16.21 standard;
E11 E16 E17 phenolic resin coated with neoprene; polyethylene isolating
E30 E32 F3 bushing; phenolic resin isolating washer and washer carbon
F10 F10R steel coated Zn-Ni; for flange class 600/900.
F11 F16 F32
JI-05 F3 F10 F10R Circular isolating gasket, for cathodic protection; flange; oval
F11 F16 G10 type R; ring type joint (RTJ); ASME B16.21 standard;
G10R G10P phenolic resin coated with neoprene; polyethylene isolating
G11 G12 bushing; phenolic resin isolating washer and washer carbon
G12P G16 steel coated Zn-Ni; for flange class 1500/2500/API 10000.
G16P
H10 H10P
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 35 of 72
JP-01 B22 B23 B24 Circular gasket; full face type for flange flat face (FF); PTFE
expand; class 150; wall thickness 1/8” (3,2 mm); ASME
B16.21 standard.
JP-02 B25 Circular gasket; full face type for flange full face (FF); armed
rubber; class 150; wall thickness 1/8” (3,2 mm); ASME
B16.21 standard.
JP-04 B11 C11 Circular gasket; raised face (RF); PTFE expand; class
150/300; wall thickness 1/8” (3,2 mm); ASME B16.21
standard.
JP-05 B11 C11 Circular gasket; full face type for flange raised face (RF);
PTFE expand; class 150/300 wall thickness 1/16” (1,6 mm);
ASME B16.21 standard.
JPH-07 A8 B5 B7 Circular gasket; flat ring type; plain; for flange raised face
B7R B9 B10 (RF); compressed sheet non asbestos; ASME B16.21
B11 B12 B13 standard; class 150; wall thickness 1/16” (1,6 mm).
B15 B16 B17
B30
JPH-08 A8 B7 B7R Circular gasket; flat ring type; plain; for flange raised face
B9 B10 B11 (RF); compressed sheet non asbestos; ASME B16.21
B12 B13 B15 standard; class 150; wall thickness 1/8” (3,2 mm).
B16 B17
JPH-09 A4 A8 B14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 150; wall thickness 1/16” (1,6 mm).
JPH-10 A4 A8 B14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 150; wall thickness 1/8 in (3,2 mm).
JPH-11 C5 C8 C9 Circular gasket; flat ring type; plain; for flange raised face
C10 C12 C13 (RF); compressed sheet non asbestos; ASME B16.21
C16 C30 standard; class 300; wall thickness 1/16 in (1,6 mm).
JPH-12 C9 C10 C12 Circular gasket; flat ring type; plain; for flange raised face
C13 C16 C30 (RF); compressed sheet non asbestos; ASME B16.21
standard; class 300; wall thickness 1/8 in (3,2 mm).
JPH-13 C14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 36 of 72
JPH-14 C14 Circular gasket; full face type; plain; for flange full face (FF);
compressed sheet non asbestos; ASME B16.21 standard;
class 300; wall thickness 1/8 in (3,2 mm).
JPH-15 B20 B21 Circular gasket; full face type; plain; for flange full face (FF);
Teflon enveloped with non-asbestos insert; ASME B16.21
standard; class 150; wall thickness 1/8 in (3,2 mm).
JVM-01 H30 H30P IX seal-rings, Inconel® 625; NORSOK CFC (compact flange
H38 H38P connections) standard L-005 (NCF5); class 2500.
JVM-02 H10 H10P IX seal-rings, carbon steel coated Zn-Ni; NORSOK CFC
H11 H14 (compact flange connections) standard L-005 (NCF5); class
2500.
JVM-03 J31 J31P J40 IX seal-rings, Inconel® 625; NORSOK CFC (compact flange
connections) standard L-005 (NCF5); class API 10000.
L-08 B6 B19 C6 Coupling; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 3000; socket weld ends.
L-09 B6 B19 C6 Coupling; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
L-15 B13 C13 Coupling; pipe line; stainless steel superduplex; ASTM A
182 Gr F 53 (UNS S32750); ASME B16.11 standard; class
3000; socket weld ends.
L-16 B12 C12 Coupling; pipe line; stainless steel superduplex; ASTM A
182 Gr F 55 (UNS S32760); ASME B16.11 standard; class
3000; socket weld ends.
L-17 B20 Coupling; pipe line; PVC poly vinyl chloride; ASTM D 1784
class 12454; dimensions ASTM D 2467; plain ends.
L-19 B22 B23 Coupling; pipe line; FRP; ASTM F 1173-01; resin according
manufacturer; with external layer, of improved resin with
ultraviolet inhibitor; butt and strap joint.
L-20 B24 Coupling; pipe line; FRP; ASTM F 1173-01; phenolic resin;
with external layer, of improved resin with ultraviolet
inhibitor; butt and strap joint.
L-23 B17 E17 Coupling; pipe line; carbon steel; ASTM A 105; ASME
B16.11 standard; class 9000; socket weld ends.
L-27 B16 C16 E16 Coupling; pipe line; duplex stainless steel; ASTM A 182 Gr F
F16 G16 51 (UNS S31803); ASME B16.11 standard; class 3000;
G16P socket weld ends.
L-28 E30 Coupling; pipe line; carbon steel; ASTM A 105; ASME B16.9
standard; buttweld ends ASME B16.25.
L-31 G19 Coupling; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 38 of 72
L-33 B30 C30 E30 Coupling; pipe line; ASTM B564 (UNS N06625); ASME
E32 F32 B16.9 standard; class 3000; socket weld ends ASME
B16.25.
L-91 B7 B7R Coupling; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA
146 standard; ASME B16.11; 20 bar pressure; capillary
female ends.
LRE-02 B9 B10 B11 Reducing coupling; pipe line; carbon steel; ASTM A 105;
B15 C9 C10 ASME B16.11 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F11 F14 G4
G10 G10R
G10P G11
G14 G18
LRE-03 B6 B19 C6 Reducing coupling; pipe line; carbon steel; ASTM A 350 Gr
E6 E6R LF2 CL1; ASME B16.11 standard; class 3000; socket weld
ends.
LRE-04 B6 B19 C6 Reducing coupling; pipe line; carbon steel; ASTM A 350 Gr
E6 E6R F6 LF2 CL1; ASME B16.11 standard; class 6000; socket weld
F6R G6 G6R ends.
LRE-07 B13 C13 Reducing coupling; pipe line; stainless steel superduplex;
ASTM A 182 Gr F 53 (UNS S32750); ASME B16.11
standard; class 3000; socket weld ends.
LRE-08 B12 C12 Reducing coupling; pipe line; stainless steel superduplex;
ASTM A 182 Gr F 53 (UNS S32760); ASME B16.11
standard; class 3000; socket weld ends.
LRE-09 B20 Reducing coupling; pipe line; PVC poly vinyl chloride; ASTM
D 1784 class 12454; dimensions ASTM D 2467; plain ends.
LRE-11 G12 G12P Reducing coupling; pipe line; stainless steel superduplex;
ASTM A 182 Gr F55 (UNS S32760); ASME B16.11
standard; class 6000; socket weld ends.
LRE-12 B17 E17 Reducing coupling; pipe line; carbon steel; ASTM A 105;
ASME B16.11 standard; class 9000; socket weld ends.
LRE-13 J12 Reducing coupling; pipe line; stainless steel superduplex;
ASTM A 182 Gr F 55 (UNS S32760); ASME B16.11
standard; class 9000; socket weld ends.
LRE-16 B16 C16 E16 Reducing coupling; pipe line; duplex stainless steel; ASTM
G16 G16P A 182 Gr F 51 (UNS S31803); ASME B16.11 standard;
class 3000; socket weld ends.
LRE-17 C30 E30 Reducing coupling; pipe line; carbon steel; ASTM A 105;
ASME B16.9 standard; buttweld ends ASME B16.25.
LRE-21 B30 C30 E30 Reducing coupling; pipe line; ASTM B564 (UNS N06625);
E32 F32 ASME B16.9 standard; class 3000; socket weld ends ASME
B16.25.
ML-01 A4 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B16.11 standard; class 3000; thread ends ASME B1.20.1
NPT.
ML-02 A8 B4 B9 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B10 B11 B14 B16.11 standard; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E10 E10R
E11 E14
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 40 of 72
ML-03 B5 B9 B10 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B11 B15 C5 B16.11 standard; class 6000; socket weld ends.
C9 C10 E5
E9 E10 F4 F5
F10 F10R
F14 G4 G5
G10 G10R
G10P G11
G14
ML-05 B6 B19 C6 Half coupling; pipe line; carbon steel; ASTM A 350 Gr LF2
E6 E6R CL1; ASME B16.11 standard; class 3000; thread ends
ASME B1.20.1 NPT.
ML-07 B6 B19 C6 Half coupling; pipe line; carbon steel; ASTM A 350 Gr LF2
E6 E6R F6 CL1; ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
ML-11 B13 C13 Half coupling; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 53 (UNS S32750); ASME B16.11 standard;
class 3000; socket weld ends.
ML-12 B12 C12 Half coupling; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 53 (UNS S32760); ASME B16.11 standard;
class 3000; socket weld ends.
ML-13 G12 G12P Half coupling; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.11 standard;
class 6000; socket weld ends.
ML-14 B17 E17 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B16.11 standard; class 9000; socket weld ends.
ML-16 J12 Half coupling; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.11 standard;
class 9000; socket weld ends.
ML-18 B16 C16 E16 Half coupling; pipe line; duplex stainless steel; ASTM A 182
F16 G16 Gr F 51 (UNUS S31803); ASME B16.11 standard; class
G16P 3000; socket weld ends.
ML-19 C30 E30 Half coupling; pipe line; carbon steel; ASTM A 105; ASME
B16.9 standard; class 3000; buttweld ends ASME B16.25.
ML-22 G19 Half coupling; pipe line; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.11 standard; class 9000; socket weld ends.
ML-23 C30 E30 E32 Half coupling; pipe line; ASTM B564 (UNS N06625); ASME
F32 B16.9 standard; class 3000; socket weld ends; ASME
B16.25.
NIPADF-91 B7 B7R Female adaptor nipple; pipe line; Cu-Ni 90/10 (UNS
C70620); EEMUA 146 standard; 20 bar pressure; thread
female ASME B1.20.1 NPT x capillary male.
NIPADM-91 B7 B7R Male adaptor nipple; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146 standard; 20 bar pressure; thread male ASME
B1.20.1 NPT x capillary male.
NIPC-07 B25 Short nipple; pipe line; RPVC-PVC coated external with fiber
glass, thermosetting resin; rigid joint ends / butt-strap (JR /
PP).
Pipe; RPVC-PVC extruded reinforced external with
thermosetting resin, fiber glass; rigid joint ends / butt-strap
(JR / PP).
NIPM-91 B7 B7R Male adaptor nipple; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146 standard; 20 bar system; thread ends ASME
B1.20.1 NPT.
NIPRC-05 B6 B19 C6 Concentric reducing nipple; pipe line; carbon steel; ASTM A
E6 E6R F6 420 Gr WPL6; MSS SP-95 standard; seamless; plain ends.
F6R G6 G6R
G19
NIPRC-05A B6 B19 C6 Concentric reducing nipple; pipe line; carbon steel; ASTM A
E6 E6R F6 420 Gr WPL6; MSS SP-95 standard; seamless; buttweld
F6R G6 G6R end ASME B16.25 x plain ends.
G19
NIPRC-08 B13 C13 Concentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32750); MSS SP-95
standard; seamless; plain ends.
NIPRC-08A B13 C13 Concentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32750); MSS SP-95
standard; seamless; buttweld end ASME B16.25 x plain
end.
NIPRC-09 B12 C12 G12 Concentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32760); MSS SP-95
standard; seamless; plain ends.
NIPRC-09A B12 C12 G12 Concentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32760); MSS SP-95
standard; seamless; buttweld end ASME B16.25 x plain
end.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 43 of 72
NIPRC-11 B16 C16 E16 Concentric swage(d) nipple, pipe line; duplex stainless steel;
F16 G16 ASTM A 815 (UNS S31803); MSS SP-95 standard;
seamless; plain ends.
NIPRC-11A B16 C16 E16 Concentric swage(d) nipple, pipe line; duplex stainless steel;
F16 G16 ASTM A 815 (UNS S31803); MSS SP-95 standard;
seamless; buttweld end ASME B16.25 x plain end.
NIPRC-13 J31 J31P Concentric swage(d) nipple, pipe line; alloy steel; ASTM A
333 Gr 8; MSS SP-95 standard; seamless; buttweld ends
ASME B16.25.
NIPRC-16 B30 C30 E30 Concentric reducing nipple; pipe line; ASTM B564 (UNS
E32 F32 N06625); MSS SP-95 standard; seamless; plain ends.
NIPRC-17 H30 H38 J40 Concentric reducing nipple; pipe line; ASTM B564 (UNS
N06625); MSS SP-95 standard; seamless; buttweld ends
ASME B16.25.
NIPRC-18 H14 Concentric reducing nipple; pipe line; ASTM A 694 Gr F65;
MSS SP-95 standard; seamless; buttweld ends ASME
B16.25.
NIPRC-20 H11 H10 Concentric reducing nipple; pipe line; carbon steel; ASTM A
234 Gr WPB; MSS SP-95 standard; seamless; buttweld
ends ASME B16.25
NIPRC-22 E32 F32 Concentric reducing nipple; pipe line; carbon steel; ASTM A
420 Gr WPL3; MSS SP-95 standard; seamless; buttweld
ends ASME B16.25 x plain ends.
NIPRE-14 B13 C13 Eccentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32750); MSS SP-95
standard; seamless; plain ends.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 45 of 72
NIPRE-14A B13 C13 Eccentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32750); MSS SP-95
standard; seamless; buttweld end ASME B16.25 x plain
end.
NIPRE-15 B12 C12 G12 Eccentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32760); MSS SP-95
standard; seamless; plain ends.
NIPRE-15A B12 C12 G12 Eccentric reducing nipple; pipe line; stainless steel
superduplex; ASTM A 815 (UNS S32760); MSS SP-95
standard; seamless; buttweld end ASME B16.25 x plain
end.
NIPRE-16 B6 B19 C6 Eccentric reducing nipple; pipe line; carbon steel; ASTM A
E6 E6R F6 420 Gr WPL 6; MSS SP-95 standard; seamless; plain ends.
F6R G6 G6R
G19
NIPRE-16A B6 B19 C6 Eccentric reducing nipple; pipe line; carbon steel; ASTM A
E6 E6R F6 420 Gr WPL 6; MSS SP-95 standard; MSS SP-95 standard;
F6R G6 G6R seamless; buttweld end ASME B16.25 x plain end.
G19
NIPRE-18 B16 C16 E16 Eccentric swage(d) nipple, pipe line; duplex stainless steel;
F16 G16 ASTM A 815 (UNS S31803); MSS SP-95 standard;
seamless; plain ends.
NIPRE-18A B16 C16 E16 Eccentric swage(d) nipple, pipe line; duplex stainless steel;
F16 G16 ASTM A 815 (UNS S31803); MSS SP-95 standard;
seamless; buttweld end ASME B16.25 x plain end.
NIPRE-20 J31 J31P Eccentric swage(d) nipple, pipe line; Alloy stell; ASTM A 333
Gr.8; MSS SP-95 standard; seamless; buttweld ends ASME
B16.25.
NIPRE-22 B30 C30 E30 Eccentric reducing nipple; pipe line; ASTM B564 (UNS
E32 F32 N06625); MSS SP-95 standard; seamless; plain ends.
NIPRE-23 H30 H38 J40 Eccentric reducing nipple; pipe line; ASTM B564 (UNS
N06625); MSS SP-95 standard; seamless; buttweld ends.
NIPRE-24 H14 Eccentric reducing nipple; pipe line; ASTM A 694 Gr F65;
MSS SP-95 standard; seamless; buttweld ends.
NIPRE-27 H6 H10 Eccentric reducing nipple; pipe line; carbon steel; ASTM A
234 Gr WPB; MSS SP-95 standard; seamless; buttweld
ends ASME B16.25.
NIPRE-29 E32 F32 Eccentric reducing nipple; pipe line; carbon steel; ASTM
A420 Gr WPL3; MSS SP-95 standard; seamless; buttweld
ends ASME B16.25 x plain ends.
PAE-01 A4 A8 B4 B5 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1/2” - 1”) B7 B7R B9 193 Gr B7, Zn-Ni (Appendix 10); heavy nuts carbon steel
B10 B11 B12 ASTM A 194 Gr 2H; Zn-Ni (Appendix 10); bolt size ASME
B13 B14 B15 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
B16 B17 B20 UNC-2A stud and screw nuts ASME B1.1 standard.
B21 B22 B23
B24 B25 B30
C3 C4 C5 C8
C9 C10 C11
C12 C13 C14
C16 C30 E4
E8 E9 E10
E10R E11
E14 E16 E17
E30 F4 F5
F10 F10R
F11 F14 G4
G5 G10
G10R G10P
G11 G12
G12P G14
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 47 of 72
G16 G16P
G18 H5 H10
H10P H11
H14 H30
H30P H38
H38P J5 J12
PAE-02 A4 B4 B7 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1 1/8” - 2”) B7R B9 B10 193 Gr B7, Zn-Ni (Appendix 10); heavy nuts carbon steel
B11 B12 B13 ASTM A 194 Gr 2H; Zn-Ni (Appendix 10); bolt size ASME
B14 B15 B16 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
B22 B23 B25 UN-2A stud and screw nuts ASME B1.1 standard.
C3 C4 C9
C10 C11 C12
C13 C14 C16
C30 E4 E8
E9 E10 E10R
E11 E14 E16
E17 E30 F4
F5 F10 F10R
F11 F14 G4
G5 G10
G10R G10P
G11 G12
G12P G14
G16 G16P
G18 H5 H10
H10P H11
H14 H30
H30P H38
H38P J5 J12
PAE-07 B3 B6 B19 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1/2” -1”) C6 E3 E5 E6 320 Gr L7 Zn-Ni (Appendix 10); heavy nuts carbon steel
E6R E32 F3 ASTM A 194 Gr 4/S3 Zn-Ni (Appendix 10); bolt size ASME
F6 F6R F32 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
G3 G6 G6R UNC-2A stud and screw nuts ASME B1.1 standard.
G19 H3 J31
J31P J40
PAE-08 B3 B6 B19 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1 1/8” - 2”) C6 E3 E5 E6 320 Gr L7, Zn-Ni (Appendix 10); heavy nuts carbon steel
E6R F3 F6 ASTM A 194 Gr 4/S3 Zn-Ni (Appendix 10); bolt size ASME
F6R E32 F32 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
G3 G6 G6R UN-2A stud and screw nuts ASME B1.1 standard.
G19 H3 J31
J31P J40
PAE-09 B9 B10 B11 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1/2” - 1”) B12 B13 B14 193 Gr B16, Zn-Ni (Appendix 10); heavy nuts carbon steel
B15 B16 B17 ASTM A 194 Gr 7 Zn-Ni (Appendix 10); bolt size ASME
B22 B25 C3 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
C4 C9 C10 UNC-2A stud and screw nuts ASME B1.1 standard.
C11 C12 C13
C14 C16 C30
E9 E10 E10R
E16 E17 E30
F10 F10R
G10 G10R
G10P G11
G12 G12P
G16 G16P
G18 H10
H10P H11
H30 H30P
H38 H38P
J12
PAE-10 B9 B10 B11 Stud bolt; with two hexagonal nuts; bolt alloy steel ASTM A
(1 1/8” - 2”) B12 B13 B14 193 Gr B16, Zn-Ni (appendix 10); heavy nuts carbon steel
B15 B16 B22 ASTM A 194 Gr 7 Zn-Ni (Appendix 10); bolt size ASME
B25 C3 C4 B18.2.1 and nuts ASME B18.2.2 standard; integral thread
C9 C10 C11 UN-2A stud and screw nuts ASME B1.1 standard.
C12 C13 C14
C16 C30 E9
E10 E10R
E16 E17 E30
F10 F10R
G10 G10R
G10P G11
G12 G12P
G16 G16P
G18 H10
H10P H11
H30 H30P
H38 H38P
J12
REDC-02 B6 B19 C6 Concentric reducer; pipe line; carbon steel; ASTM A 420 Gr
E6 E6R F6 WPL6; ASME B16.9 standard; buttweld ends ASME B16.25.
F6R G6 G6R
G19 H6
REDC-05 G11 G14 Concentric reducer; pipe line; carbon steel; ASTM A 694 Gr
G18 F60; ASME B16.9 standard; buttweld ends ASME B16.25.
REDC-06 B13 C13 Concentric reducer; pipe line; stainless steel superduplex;
ASTM A 815 (UNS S32750); ASME B16.9 standard;
buttweld ends ASME B16.25.
REDC-07 B12 C12 G12 Concentric reducer; pipe line; stainless steel superduplex;
J12 ASTM A 815 (UNS S32760); ASME B16.9 standard;
buttweld ends ASME B16.25.
REDC-08 B22 B23 Concentric reducer; pipe line; FRP; ASTM F 1173-01; resin
according manufacturer; with external layer, of improved
resin with ultraviolet inhibitor; butt and strap joint.
REDC-10 B15 Concentric reducer; pipe line; carbon steel; spec Mariloy
(S400/TPY); welded (JIS G 3454/57) buttweld ends ASME
B16.25.
REDC-14 G10 H10 Concentric reducer; pipe line; carbon steel; ASTM A 694 Gr
H10P H11 F65; ASME B16.9 standard; buttweld ends ASME B16.25.
H14 H30 J5
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 50 of 72
REDC-15 B16 C16 E16 Concentric reducer, pipe line; dupex stainless steel; ASTM
F16 G16 A 815 (UNS S31803); ASME B16.9 standard; buttweld ends
ASME B16.25.
REDC-16 J31 J31P Concentric reducer, pipe line; Alloy steel; ASTM A 420 Gr.
WPL8; ASME B16.9 standard; buttweld ends ASME B16.25
REDC-17 E32 F32 Concentric reducer, pipe line; Alloy steel; ASTM A 420 Gr.
WPL3; ASME B16.9 standard; buttweld ends ASME B16.25
REDC-19 J40 Concentric reducer; pipe line; carbon steel; ASTM B564
(UNS N06625); ASME B16.9 standard; buttweld ends
ASME B16.25.
REDC-20 H38 Concentric reducer; pipe line; carbon steel; ASTM A 694 Gr
F80; ASME B16.9 standard; buttweld ends ASME B16.25.
REDC-91 B7 B7R Concentric reducer; pipe line; Cu-Ni 90/10 (UNS C70620);
20 bar pressure; EEMUA 146 standard; ASME B16.9;
buttweld ends ASME B16.25.
REDC-92 B7R Concentric reducer; pipe line; Cu-Ni 90/10 (UNS C70620);
16 bar pressure; EEMUA 146 standard; ASME B16.9;
buttweld ends ASME B16.25.
REDE-02 B6 B19 C6 Eccentric reducer; pipe line; carbon steel; ASTM A 420 Gr
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 51 of 72
REDE-05 G11 G14 Eccentric reducer; pipe line; carbon steel; ASTM A 694 Gr
G18 F60; ASME B16.9 standard; buttweld ends ASME B16.25.
REDE-06 B13 C13 Eccentric reducer; pipe line; stainless steel superduplex;
ASTM A 815 (UNS S32750); ASME B16.9 standard;
buttweld ends ASME B16.25.
REDE-07 B12 C12 G12 Eccentric reducer; pipe line; stainless steel superduplex;
J12 ASTM A 815 (UNS S32760); ASME B16.9 standard;
buttweld ends ASME B16.25.
REDE-08 B22 B23 Eccentric reducer; pipe line; FRP; ASTM F 1173-01; resin
according manufacturer; with external layer, of improved
resin with ultraviolet inhibitor; butt and strap joint.
REDE-13 G10 H10 Eccentric reducer; pipe line; carbon steel; ASTM A 694 Gr
H10P H11 F65; ASME B16.9 standard; buttweld ends ASME B16.25.
H14 H30 J5
REDE-14 B16 C16 E16 Eccentric reducer, pipe line; dupex stainless steel; ASTM A
F16 G16 815 (UNS S31803); ASME B16.9 standard; buttweld ends
ASME B16.25.
REDE-15 J31 J31P Eccentric reducer; pipe line; Alloy steel; ASTM A 420 Gr.
WPL8; ASME B16.9 standard; buttweld ends ASME B16.25
REDE-16 E32 F32 Eccentric reducer; pipe line; Alloy steel; ASTM A 420 Gr.
WPL3; ASME B16.9 standard; buttweld ends ASME B16.25
REDE-18 J40 Concentric reducer; pipe line; carbon steel; ASTM B564
(UNS N06625); ASME B16.9 standard; buttweld ends
ASME B16.25.
REDE-19 H38 Eccentric reducer; pipe line; carbon steel; ASTM A 694 Gr
F80; ASME B16.9 standard; buttweld ends ASME B16.25.
REDE-91 B7R Eccentric reducer; pipe line; Cu-Ni 90/10 (UNS C70620); 16
bar pressure; EEMUA 146 standard; ASME B16.9; buttweld
ends ASME B16.25.
SAD-03 B22 B23 Reducing saddle; pipe line; ASTM F 1173-01; resin
according manufacturer; with external layer, of improved
resin with ultraviolet inhibitor; flanged ends.
SAD-05 B22 B23 Reducing saddle; pipe line; ASTM F 1173-01; resin
according manufacturer; with external layer, of improved
resin with ultraviolet inhibitor; thread ends ASME B1.20.1
NPT.
SAD-06 B24 Reducing saddle; pipe line; ASTM F 1173-01; phenolic resin
with external layer, of improved resin with ultraviolet
inhibitor; thread ends ASME B1.20.1 NPT.
SKL-91 B7 B7R Sockolet; pipe line; socket welding type; Cu-Ni 90/10 (UNS
C70620); EEMUA 146 standard; 20 bar pressure; capillary
ends.
T-03B A4 B10 B11 Welded pipe, (E=0,95); carbon steel; API 5L Gr B PSL 1;
C4 C30 E10 ASME B36.10 standard; buttweld ends ASME B16.25.
E10R E30
F10 F10R
F14 G4 G5
G10 G10P
G10R G11
G14 G18
T-13 B13 C13 Seamless pipe; stainless steel superduplex; ASTM A 790
(UNS S32750); ASME B36.19 standard; plain ends.
T-15 B13 C13 Seamless pipe; stainless steel superduplex; ASTM A 790
(UNS S32750); ASME B36.19 standard; buttweld ends
ASME B16.25.
T-17 B12 C12 G12 Seamless pipe; stainless steel superduplex; ASTM A 790
G12P J12 (UNS S32760); ASME B36.19 standard; plain ends.
T-19 B12 C12 G12 Seamless pipe; stainless steel superduplex; ASTM A 790
G12P J12 (UNS S32760); ASME B36.19 standard; buttweld ends
ASME B16.25.
T-21 B15 Welded pipe; carbon steel; spec Mariloy (S400/TPY); JIS G
3454/57 standard; buttweld ends ASME B16.25.
T-22 B20 Seamless pipe; PVC poly vinyl chloride; ASTM D 1785 PVC
1120; dimensions ASTM D 1785; plain ends.
(JR / PP).
T-27 B22 B23 Pipe; FRP; ASTM F 1173-01; resin according manufacturer
with external layer, of improved resin with ultraviolet
inhibitor; butt and strap joint.
T-28 B24 Pipe; FRP; ASTM F 1173-01; phenolic resin with external
layer, of improved resin with ultraviolet inhibitor; butt and
strap joint.
T-29 G11 G14 Welded pipe, (E=0,95); carbon steel; API 5L Gr X 60 PSL 1;
ASME B36.10 standard; buttweld ends ASME B16.25.
T-36 B16 C16 E16 Seamless pipe; duplex stainless steel; ASTM A 790 (UNS
F16 G16 S31803); ASME B36.19 standard; plain ends.
G16P
T-37A B16 C16 E16 Seamless pipe; duplex stainless steel; ASTM A 790 (UNS
F16 G16 S31803); ASME B36.19 standard; buttweld ends ASME
G16P B16.25.
T-38A G10P H14 Seamless pipe; carbon steel; API 5L Gr X 65 PSL 1; ASME
B36.10 standard; buttweld ends ASME B16.25.
T-39 G18 H11 Welded, (E=0,85); pipe; carbon steel; API 5L Gr X 70 PSL
1; ASME B36.10M standard; buttweld ends ASME B16.25.
T-40 J31 J31P Seamless pipe; nickel alloy steel; ASTM A 333 Gr 8; ASME
B36.10 standard; buttweld ends ASME B16.25.
T-42 B30 C30 E30 Seamless pipe; ASTM B444 Gr1 (UNS N06625); ASME
E32 F32 B36.19 standard; plain ends.
T-43 H30 H30P Seamless pipe; ASTM B444 Gr1 (UNS N06625); ASME
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 56 of 72
T-45 E10 F10 G10 Welded, (E=1); pipe; carbon steel; API 5L Gr X 65 PSL 2;
G10P H10P ASME B36.10M standard; buttweld ends ASME B16.25.
H30 H30P
T-46 E10 F10 G10 Seamless pipe; carbon steel; API 5L Gr X 65 PSL 2; ASME
H10 H10P B36.10 standard; buttweld ends ASME B16.25.
H30 H30P
T-47 B16 C16 E16 Welded pipe, (E=1); stainless steel duplex; ASTM A 928
F16 G16 (UNS S31803 class 1 or 3); ASME B36.19 standard;
G16P buttweld ends ASME B16.25.
T-48 B13 C13 Welded pipe, (E=1); stainless steel superduplex; ASTM A
928 (UNS S32750); ASME B36.19 standard; buttweld ends
ASME B16.25.
T-49 B12 C12 G12 Welded pipe, (E=1); stainless steel superduplex; ASTM A
G12P 928 (UNS S32760); ASME B36.19 standard; butttweld ends
ASME B16.25.
T-50 E32 F32 Seamless pipe; carbon steel; ASTM A 333 Gr 3; ASME
B36.10 standard; buttweld ends ASME B16.25.
T-54 F32 Welded pipe, (E=1); carbon steel; ASTM A 333 Gr 3; ASME
B36.10 standard; buttweld ends ASME B16.25.
T-55 H38 H38P Seamless pipe; carbon steel; API 5L Gr X80 PSL 2; ASME
B36.10 standard; buttweld ends ASME B16.25.
T-56 H38 H38P Welded pipe, (E=1); carbon steel; API 5L Gr X80 PSL 2;
ASME B36.10 standard; buttweld ends ASME B16.25.
T-61 B7R Seamless pipe; Cu-Ni 90/10 (UNS C70620); EEMUA 144
standard; buttweld ends ASME B16.25.
T-62 B7R Welded pipe, (E=1); Cu-Ni 90/10 (UNS C70620); EEMUA
144 standard; buttweld ends ASME B16.25.
T-90 B7 B7R Seamless pipe; Cu-Ni 90/10 (UNS C70620); EEMUA 144
standard; plain ends.
T-91 B7 B7R Seamless pipe; Cu-Ni 90/10 (UNS C70620); EEMUA 144
standard; buttweld ends ASME B16.25.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 57 of 72
TAM-01 A4 B4 B9 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; class 3000; thread ends ASME B1.20.1 NPT.
B30 C4 C5
C9 C11 E10
E10R E11
E14 E17
TAM-02 A4 A8 B4 B5 Cap; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; buttweld ends ASME B16.25.
B14 B15 B17
C4 C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E17 E30
F4 F5 F10
F10R F11
F14 G4 G5
G10 G10R
G11 G14
G18 H5 H10
H11
TAM-04 A8 B4 B9 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; class 3000; thread ends ASME B1.20.1 NPT.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
TAM-05 A8 B4 B9 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
TAM-06 B9 B10 B15 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
C9 C10 E9 standard; class 6000; socket weld ends.
E10 F4 F10
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 58 of 72
F10R F11
F14 G4 G10
G10R G10P
G11 G14
G18
TAM-07 B6 B19 C6 Cap; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 3000; thread ends ASME
B1.20.1 NPT.
TAM-08 B6 B19 C6 Cap; pipe line; carbon steel; ASTM A 420 Gr WPL6; ASME
E6 E6R F6 B16.9 standard; buttweld ends ASME B16.25.
F6R G6 G6R
G19 H6
TAM-09 B6 B19 C6 Cap; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 3000; socket weld ends.
TAM-12 B6 B19 C6 Cap; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
TAM-14 B3 C3 E3 F3 Cap; pipe line; carbon steel; ASTM A 182 Gr F 316L; ASME
B16.11 standard; class 3000; thread ends ASME B1.20.1
NPT.
TAM-15 B5 B9 B10 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
B15 B17 C5 standard; class 6000; thread ends ASME B1.20.1 NPT.
C9 E9 E10
E11 E17 F4
G11
TAM-16 B6 B19 C6 Cap; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 6000; thread ends ASME
B1.20.1 NPT.
TAM-18 G3 H3 Cap; pipe line; stainless steel; ASTM A 182 Gr F 316; ASME
B16.9 standard; class 3000; thread ends ASME B1.20.1
NPT.
TAM-21 B13 C13 Cap; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 53 (UNS S32750); ASME B16.11 standard; class 3000;
socket weld ends.
TAM-22 B12 C12 Cap; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 3000;
socket weld ends.
TAM-23 B20 Cap; pipe line; PVC poly vinyl chloride; ASTM D 1784 class
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 59 of 72
TAM-24 B21 Cap; pipe line; CPVC chlorinated polyvinyl chloride; ASTM
D 1784 class 23447; dimensions ASTM F 439; socket weld
ends.
TAM-26 B13 C13 Cap; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; buttweld ends
ASME B16.25.
TAM-27 B12 C12 G12 Cap; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; buttweld ends
ASME B16.25.
TAM-28 G11 G14 Cap; pipe line; carbon steel; ASTM A 694 Gr F60; ASME
G18 B16.9 standard; buttweld ends ASME B16.25.
TAM-29 G12 G12P Cap; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 6000;
socket weld ends.
TAM-30 H11 J5 Cap; pipe line; carbon steel; ASTM A 694 Gr F70; ASME
B16.9 standard; buttweld ends ASME B16.25.
TAM-31 E30 H10 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.9
H10P H11 standard; buttweld ends ASME B16.25.
H30
TAM-32 J12 Cap; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 9000;
socket weld ends.
TAM-33 B17 E17 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; class 9000; socket weld ends.
TAM-34 G19 Cap; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.11 standard; class 9000; socket weld ends.
TAM-35 B16 C16 E16 Cap; pipe line; duplex stainless steel; ASTM A 182 Gr F 51
F16 G16 (UNS S31803); ASME B16.11 standard; class 3000; socket
G16P weld ends.
TAM-36 B16 C16 E16 Cap; pipe line; duplex stainless steel; ASTM A 815 (UNS
F16 G16 S31803); ASME B16.9 standard; buttweld ends ASME
B16.25.
TAM-37 B16 C16 E16 Cap; pipe line; duplex stainless steel; ASTM A 815 (UNS
F16 G16 S31803); ASME B16.11 standard; class 3000; thread ends
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 60 of 72
TAM-40 J31 J31P Cap; pipe line; Alloy steel; ASTM A 420 Gr. WPL8; ASME
B16.9 standard; buttweld ends ASME B16.25
TAM-43 H10 H14 H30 Cap; pipe line; carbon steel; ASTM A 694 Gr F65; ASME
B16.9 standard; buttweld ends ASME B16.25.
TAM-44 B12 C12 Cap; pipe line; carbon steel; ASTM A 182 Gr F55 (UNS
S32760); ASME B16.11 standard; class 3000; thread ends
ASME B1.20.1 NPT.
TAM-45 B13 C13 Cap; pipe line; carbon steel; ASTM A 182 Gr F53 (UNS
S32750); ASME B16.11 standard; class 3000; thread ends
ASME B1.20.1 NPT.
TAM-46 G16 G16P Cap; pipe line; carbon steel; ASTM A 182 Gr F 51 (UNS
S31803); ASME B16.11 standard; class 3000; thread ends
ASME B1.20.1 NPT.
TAM-47 E32 F32 Cap; pipe line; Alloy steel; ASTM A 420 Gr. WPL3; ASME
B16.9 standard; buttweld ends ASME B16.25
TAM-48 B30 C30 E30 Cap; pipe line; ASTM B564 (UNS N06625); ASME B16.11
E32 F32 standard; class 3000; socket weld ends; ASME B16.25.
TAM-51 J40 Cap; pipe line; ASTM B564 (UNS N06625); ASME B16.9
standard; class 10000; buttweld end; ASME B16.25.
TAM-52 H30 H30P Cap; pipe line; ASTM B564 (UNS N06625); ASME B16.9
H38 H38P standard; class 2500; buttweld end; ASME B16.25.
TAM-54 B17 E17 Cap; pipe line; carbon steel; ASTM A 105; ASME B16.11
standard; class 9000; thread ends ASME B1.20.1 NPT.
TAM-56 H38 Cap; pipe line; carbon steel; ASTM A 694 Gr F80; ASME
B16.9 standard; buttweld ends ASME B16.25.
TAM-91 B7 B7R Cap; pipe line; Cu-Ni 90/10 (UNS C70620); 20 bar pressure;
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 61 of 72
TAM-93 B7 B7R Cap; pipe line; Cu-Ni 90/10 (UNS C70620); 20 bar pressure;
EEMUA 146 standard; ASME B16.9; buttweld ends ASME
B16.25.
TAM-94 B7R Cap; pipe line; Cu-Ni 90/10 (UNS C70620); 16 bar pressure;
EEMUA 146 standard; ASME B16.9; buttweld ends ASME
B16.25.
TE-02 A4 A8 B4 B5 Tee; pipe line; carbon steel; ASTM A 234 Gr WPB; ASME
B9 B10 B11 B16.9 standard; buttweld ends ASME B16.25.
B14 B15 C4
C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10 E10R
E11 E14 E17
E30 F4 F5
F10 F10R
F11 F14 G4
G5 G10
G10R G10P
G11 G14
G18 H5 H10
H11
TE-05 A8 B4 B9 Tee; pipe line; carbon steel; ASTM A 105; ASME B16.11
B10 B11 B14 standard; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E10R E11
E14
TE-06 B9 B10 B15 Tee; pipe line; carbon steel; ASTM A 105; ASME B16.11
C9 C10 C15 standard; class 6000; socket weld ends.
E9 E10 F4
F10 F10R
F11 F14 G4
G10 G10R
G10P G11
G14 G18
TE-08 B6 B19 C6 Tee; pipe line; carbon steel; ASTM A 420 Gr WPL6; ASME
E6 E6R B16.9 standard; buttweld ends ASME B16.25.
F6R G6
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 62 of 72
G6R G19 H6
TE-09 B6 B19 C6 Tee; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R ASME B16.11 standard; class 3000; socket weld ends.
TE-12 B6 B19 C6 Tee; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
E6 E6R F6 ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
TE-17 B13 C13 Tee; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 53 (UNS S32750); ASME B16.11 standard; class 3000;
socket weld ends.
TE-18 B12 C12 Tee; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 3000;
socket weld ends.
TE-19 B20 Tee; pipe line; PVC poly vinyl chloride; ASTM D 1784 class
12454; dimensions ASTM D 2467; plain ends.
TE-20 B21 Tee; pipe line; CPVC chlorinated polyvinyl chloride; ASTM D
1784 class 23447; dimensions ASTM F 439; plain ends.
TE-22 H11 J5 Tee; pipe line; carbon steel; ASTM A 694 Gr F70; ASME
B16.9 standard; buttweld ends ASME B16.25.
TE-23 G11 G14 Tee; pipe line; carbon steel; ASTM A 694 Gr F60; ASME
G18 B16.9 standard; buttweld ends ASME B16.25.
TE-23P G10P Tee; pipe line; piggable; with guide bars; carbon steel;
ASTM A 694 Gr F60; ASME B16.9 standard; buttweld ends
ASME B16.25.
TE-24 B13 C13 Tee; pipe line; stainless steel superduplex; ASTM A 815
(UNS S32750); ASME B16.9 standard; buttweld ends
ASME B16.25.
TE-25 B12 C12 G12 Tee; pipe line; stainless steel superduplex; ASTM A 815
J12 (UNS S32760); ASME B16.9 standard; buttweld ends
ASME B16.25.
TE-25P G12P Tee; pipe line; piggable; stainless steel superduplex; ASTM
A 815 (UNS S32760); ASME B16.9 standard; buttweld ends
ASME B16.25.
TE-26 B22 B23 Tee; pipe line; FRP; ASTM F 1173-01; resin according
manufacturer; with external layer, of improved resin with
ultraviolet inhibitor; butt and strap joint.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 63 of 72
TE-27 B24 Tee; pipe line; FRP; ASTM F 1173-01; phenolic resin; with
external layer, of improved resin with ultraviolet inhibitor;
butt and strap joint.
TE-28 B15 Tee; pipe line; carbon steel; Mariloy (S400/TPY); welded
(JIS G 3454/57); buttweld ends ASME B16.25.
TE-29 B25 Tee; pipe line; RPVC-PVC coated external with fiber glass,
thermosetting resin; rigid joint ends / butt-strap (JR / PP).
TE-31 B25 Tee; pipe line; RPVC-PVC coated external with fiber glass,
thermosetting resin; rigid joint ends / flange-flange (JR / FF).
TE-33 G12 G12P Tee; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 6000;
socket weld ends.
TE-34 B17 E17 H10 Tee; pipe line; carbon steel; ASTM A 105; ASME B16.9
H10P H11 standard; buttweld ends ASME B16.25
TE-35 J12 Tee; pipe line; stainless steel superduplex; ASTM A 182 Gr
F 55 (UNS S32760); ASME B16.11 standard; class 9000;
socket weld ends.
TE-38 B16 C16 E16 Tee, pipe line; duplex stainless steel; ASTM A 182 Gr F 51
F16 G16 (UNS S31803); ASME B16.11 standard; class 3000; socket
G16P weld ends.
TE-39 B16 C16 E16 Tee, pipe line; duplex stainless steel; ASTM A 815 (UNS
F16 G16 S31803); ASME B16.9 standard; buttweld ends ASME
B16.25.
TE-39P G16P Tee, pipe line; duplex stainless steel; ASTM A 815 (UNS
S31803); ASME B16.9 standard; buttweld ends ASME
B16.25.
TE-41 E30 Tee, pipe line; carbon steel; ASTM A 105; ASME B16.9
standard; buttweld ends ASME B16.25.
TE-42 G10 H10 H14 Tee, pipe line; carbon steel; ASTM A 694 Gr F65; ASME
H30 B16.9 standard; buttweld ends ASME B16.25.
TE-42P H10P H30P Tee, pipe line; piggable; with guide bars; carbon steel;
ASTM A 694 Gr F65; ASME B16.9 standard; buttweld ends
ASME B16.25
TE-43 J31 J31P Tee, pipe line; alloy steel; ASTM A 420 Gr WPL8; ASME
B16.9 standard; buttweld ends ASME B16.25.
TE-43P J31P Tee, pipe line; piggable; with guide bars; carbon steel;
ASTM A 420 Gr WPL8; ASME B16.9 standard; buttweld
ends ASME B16.25
TE-47 G19 Tee; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.11 standard; class 9000; socket weld ends.
TE-48 H6 Tee; pipe line; carbon steel; ASTM A 350 Gr LF2 CL1;
ASME B16.9 standard; buttweld ends ASME B16.25.
TE-49 A4 Tee; pipe line; carbon steel; ASTM A 105; ASME B16.9
standard; class 2000; thread ends ASME B1.20.1 NPT.
TE-50 B30 C30 Tee, pipe line; ASTM B564 (UNS N06625); ASME B16.9
E30 E32 F32 standard; class 3000; socket weld ends ASME B16.25.
TE-51 H30 H30P Tee, pipe line; ASTM B564 (UNS N06625); ASME B16.9
H38 H38P standard; buttweld ends ASME B16.25.
J40
TE-52 E32 F32 Tee, pipe line; carbon steel ASTM A420 Gr WPL3; ASME
B16.9 standard; buttweld ends ASME B16.25.
TE-54 H38 Tee, pipe line; carbon steel; ASTM A 694 Gr F80; ASME
B16.9 standard; buttweld ends ASME B16.25.
TE-54P H38P Tee, pipe line; piggable; with guide bars; carbon steel;
ASTM A 694 Gr F80; ASME B16.9 standard; buttweld ends
ASME B16.25
TE-91 B7 B7R Tee; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.11; 20 bar pressure; capillary female
ends.
TE-93 B7 B7R Tee; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 20 bar pressure; buttweld ends
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 65 of 72
ASME B16.25.
TE-94 B7R Tee; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA 146
standard; ASME B16.9; 16 bar pressure; buttweld ends
ASME B16.25.
TEY-01 B20 Tee 45 degrees; pipe line; PVC poly vinyl chloride; ASTM D
1784 class 12454; dimensions ASTM D 2467; socket weld
ends.
THL-91 B7 B7R Thredolet; pipe line; Cu-Ni 90/10 (UNS C70620); EEMUA
146 standard; 20 bar pressure; thread female ends ASME
B1.20.1 NPT.
TRE-01 A4 A8 B4 B5 Reducing tee; pipe line; carbon steel; ASTM A 234 Gr WPB;
B9 B10 B11 ASME B16.9 standard; buttweld ends ASME B16.25.
B14 B15 C4
C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E17 E30
F4 F5 F10
F10R F11
F14 G4 G5
G10 G10R
G11 G14
G18 H5 H10
H11
TRE-02 A8 B4 B9 Reducing tee; pipe line; carbon steel; ASTM A 105; ASME
B10 B11 B14 B16.11 standard; class 3000; socket weld ends.
C4 C8 C9
C10 C11 C14
E4 E8 E10
E11 E10R
E14
TRE-03 B9 B10 B11 Reducing tee; pipe line; carbon steel; ASTM A 105; ASME
B15 C9 C10 B16.11 standard; class 6000; socket weld ends.
E9 E10 E11
F4 F10 F10R
F11 F14 G4
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 66 of 72
G10 G10R
G10P G11
G14 G18
TRE-04 B6 B19 C6 Reducing tee; pipe line; carbon steel; ASTM A 420 Gr
E6 E6R F6 WPL6; ASME B16.9 standard; buttweld ends ASME
F6R G6 G6R B16.25.
G19 H6
TRE-05 B6 B19 C6 Reducing tee; pipe line; carbon steel; ASTM A 350 Gr LF2
E6 E6R CL1; ASME B16.11 standard; class 3000; socket weld ends.
TRE-08 B6 B19 C6 Reducing tee; pipe line; carbon steel; ASTM A 350 Gr LF2
E6 E6R F6 CL1; ASME B16.11 standard; class 6000; socket weld ends.
F6R G6 G6R
TRE-12 B13 C13 Reducing tee; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 53 (UNS S32750); ASME B16.11 standard;
class 3000; socket weld ends.
TRE-13 B12 C12 Reducing tee; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.11 standard;
class 3000; socket weld ends.
TRE-14 B20 Reducing tee; pipe line; PVC poly vinyl chloride; ASTM D
1784 class 12454; dimensions ASTM D 2467; plain ends.
TRE-17 G11 G14 Reducing tee; pipe line; ASTM A 694 Gr F60; ASME B16.9
G18 standard; buttweld ends ASME B16.25.
TRE-18 B13 C13 Reducing tee; pipe line; stainless steel superduplex; ASTM
A 815 (UNS S32750); ASME B16.9 standard; buttweld ends
ASME B16.25.
TRE-19 B12 C12 G12 Reducing tee; pipe line; stainless steel superduplex; ASTM
J12 A 815 (UNS S32760); ASME B16.9 standard; buttweld ends
ASME B16.25.
TRE-20 B22 B23 Reducing tee; pipe line; FRP; ASTM F 1173-01; resin
according manufacturer; with external layer, of improved
resin with ultraviolet inhibitor; butt and strap joint.
TRE-21 B24 Reducing tee; pipe line; FRP; ASTM F 1173-01; phenolic
resin with external layer, of improved resin with ultraviolet
inhibitor; butt and strap joint.
TRE-22 B15 Reducing tee; pipe line; carbon steel; Mariloy (S400/TPY);
welded (JIS G 3454/57); buttweld ends ASME B16.25.
TRE-23 B25 Reducing tee; pipe line; RPVC-PVC coated external with
fiber glass, thermosetting resin; rigid joint ends / butt-strap
(JR / PP).
TRE-25 B25 Reducing tee; pipe line; RPVC-PVC coated external with
fiber glass, thermosetting resin; rigid joint ends / flange-
flange (JR / FF).
TRE-27 G12 G12P Reducing tee; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.11 standard;
class 6000; socket weld ends.
TRE-28 H11 J5 Reducing tee; pipe line; ASTM A 694 Gr F70; ASME B16.9
standard; buttweld ends ASME B16.25.
TRE-29 B17 E17 Reducing tee; pipe line; ASTM A 105; ASME B16.9
standard; buttweld ends ASME B16.25.
TRE-30 J12 Reducing tee; pipe line; stainless steel superduplex; ASTM
A 182 Gr F 55 (UNS S32760); ASME B16.11 standard;
class 9000; socket weld ends.
TRE-33 B16 C16 E16 Reducing tee; pipe line; duplex stainless steel; ASTM A 182
F16 G16 Gr F 51 (UNS S31803); ASME B16.11 standard; class
G16P 3000; socket weld ends.
TRE-34 B16 C16 E16 Reducing tee; pipe line; duplex stainless steel; ASTM A 815
F16 G16 (UNS S31803); ASME B16.9 standard; buttweld ends
ASME B16.25.
TRE-34P G16P Reducing tee; pipe line; duplex stainless steel; ASTM A 815
(UNS S31803); ASME B16.9 standard; buttweld ends
ASME B16.25.
TRE-35 E30 H10 Reducing tee; pipe line; ASTM A 105; ASME B16.9
H10P H11 standard; buttweld ends ASME B16.25.
TRE-36 G10 H10 H14 Reducing tee; pipe line; ASTM A 694 Gr F65; ASME B16.9
H30 standard; buttweld ends ASME B16.25.
TRE-37P G10P H10P Reducing tee; pipe line; piggable; with guide bars; ASTM A
H30P 694 Gr F65; ASME B16.9 standard; buttweld ends ASME
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 68 of 72
B16.25.
TRE-38 J31 J31P Reducing tee; pipe line; alloy steel; ASTM A 420 Gr WPL8;
ASME B16.9 standard; buttweld ends ASME B16.25
TRE-38P J31P Reducing tee; pipe line; piggable; with guide bars; alloy
steel; ASTM A 420 Gr WPL8; ASME B16.9 standard;
buttweld ends ASME B16.25
TRE-42 G19 Reducing tee; pipe line; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.11 standard; class 9000; socket weld ends.
TRE-43 E32 F32 Reducing tee; pipe line; carbon steel ASTM A420 Gr WPL3;
ASME B16.9 standard; buttweld ends ASME B16.25.
TRE-44 B30 C30 E30 Reducing tee; pipe line; ASTM B564 (UNS N06625); ASME
E32 F32 B16.9 standard; class 3000; socket weld ends ASME
B16.25.
TRE-45 H30 H30P Reducing tee; pipe line; ASTM B564 (UNS N06625); ASME
H38 H38P B16.9 standard; buttweld ends ASME B16.25.
J40
TRE-46 H6 Reducing tee; pipe line; carbon steel; ASTM A 350 Gr LF2
CL1; ASME B16.9 standard; buttweld ends ASME B16.25.
TRE-48 H38 Reducing tee; pipe line; ASTM A 694 Gr F80; ASME B16.9
standard; buttweld ends ASME B16.25.
TRE-48P H38P Reducing tee; pipe line; piggable; with guide bars; ASTM A
694 Gr F80; ASME B16.9 standard; buttweld ends ASME
B16.25.
TRE-93 B7 B7R Reducing tee; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146 standard; ASME B16.9; 20 bar pressure;
buttweld ends ASME B16.25.
TRE-94 B7R Reducing tee; pipe line; Cu-Ni 90/10 (UNS C70620);
EEMUA 146 standard; ASME B16.9; 16 bar pressure;
buttweld ends ASME B16.25.
UN FLEX-01 A4 Flexible union; pipe line; lug nut type; carbon steel; ASTM A
105; 5 degrees maximum angle deflection; integral spherical
seat; maximum pressure 3000 Psi; thread ends API 5B LP.
UN ISOL-01 A4 Pipe union; carbon steel; ASTM A 105; plain seat; dielectric-
insulated gasket; class 3000; thread ends ASME B1.20.1
NPT.
UN-05 B9 B10 B15 Pipe union; carbon steel; ASTM A 105; MSS SP-83
C9 C10 E9 standard; integral conical seat; class 6000; socket weld
E10 F4 F10 ends ASME B16.11.
F10R F11
F14 G4 G10
G10R G10P
G11 G14
G18
UN-07 B6 B19 C6 Pipe union; carbon steel; ASTM A 350 Gr LF2 CL1; BS
E6 E6R 3799 standard; integral conical seat; class 3000; socket
weld ends ASME B16.11.
UN-09 B6 B19 C6 Pipe union; carbon steel; ASTM A 350 Gr LF2 CL1; MSS
E6 E6R F6 SP-83 standard; integral conical seat; class 6000; socket
F6R G6 G6R weld ends ASME B16.11.
UN-14 B13 C13 Pipe union; stainless steel superduplex; ASTM A 182 Gr F
53 (UNS S32750); integral conical seat; MSS SP-83
standard; class 3000; socket weld ends ASME B16.11.
UN-15 B12 C12 Pipe union; stainless steel superduplex; ASTM A 182 Gr F
55 (UNS S32760); integral conical seat; MSS SP-83
standard; class 3000; socket weld ends ASME B16.11.
PETROBRAS/E&P-ENGP/IPP/EISA Approved 24/04/2012 CORPORATE INFORMATION
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTS
DR-ENGP-1.1-R.6 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 70 of 72
UN-16 B20 Pipe union; PVC poly vinyl chloride; ASTM D 1784 class
12454; dimensions ASTM D 2464; plain ends.
UN-18 G12 G12P Pipe union; stainless steel superduplex; ASTM A 182 Gr F
55 (UNS S32760); integral conical seat; MSS SP-83
standard; class 6000; socket weld ends ASME B16.11.
UN-19 B17 E17 Pipe union; carbon steel; ASTM A 105; integral conical seat;
manufacturer standard; class 9000; socket weld ends ASME
B16.11.
UN-23 B16 C16 E16 Pipe union; duplex stainless steel; ASTM A 182 Gr F 51
F16 G16 (UNS S31803); integral conical seat; manufacturer
G16P standard; class 3000; socket weld ends.
UN-24 C30 E30 Pipe union; carbon steel; ASTM A 105 standard; integral
conical seat; class 3000; buttweld ends ASME B16.25.
UN-27 G19 Pipe union; carbon steel; ASTM A 350 Gr LF2 CL1; integral
conical seat; manufacturer standard; class 9000; socket
weld ends.
UN-29 B30 C30 E30 Pipe union; ASTM B564 (UNS N06625); integral conical
E32 F32 seat; class 3000; socket weld ends ASME B16.25.
UN-91 B7 B7R Pipe union; Cu-Ni 90/10 (UNS C70620); 20 bar pressure;
EEMUA 146 standard; capillary female ends.
UNADF-91 B7 B7R Female adapter union; pipe line; Cu-Ni 90/10 (UNS
C70620); 20 bar pressure; EEMUA 146 standard; thread
female end ASME B1.20.1 NPT x capillary female end.
UNADM-91 B7 B7R Male adapter union; pipe line; Cu-Ni 90/10 (UNS C70620);
20 bar pressure; EEMUA 146 standard; thread female end
ASME B1.20.1 NPT x capillary male end.
WOL-01 A4 A8 B4 B5 Weldolet; pipe line; carbon steel; ASTM A 105; MSS SP-97
B9 B10 B11 standard; buttweld ends ASME B16.25.
B14 B15 B17
C4 C5 C8 C9
C10 C11 C14
C30 E4 E5
E8 E9 E10
E10R E11
E14 E30 F4
F5 F10 F10R
F11 F14 G4
G5 G10
G10R G11
G14 G18 H5
H10 H11 H30
WOL-02 B6 B19 C6 Weldolet; pipe line; carbon steel; ASTM A 420 Gr WPL 6;
E6 E6R F6 MSS SP-97 standard; buttweld ends ASME B16.25.
F6R G6 G6R
G19 H6
WOL-05 B12 C12 G12 Weldolet; pipe line; stainless steel; ASTM A 182 Gr F 55
J12 (UNS S32760); MSS SP-97 standard; buttweld ends ASME
B16.25.
WOL-06 B13 C13 Weldolet; pipe line; stainless steel; ASTM A 182 Gr F 53
(UNS S32750); MSS SP-97 standard; buttweld ends ASME
B16.25.
WOL-07 B16 C16 E16 Weldolet; pipe line; duplex stainless steel; ASTM A 182 Gr F
F16 G16 51 (UNS S31803); MSS SP-97 standard; buttweld ends
ASME B16.25.
WOL-08 J31 J31P Weldolet; pipe line; alloy steel; ASTM A 522 type I; MSS
SP-97 standard; buttweld ends ASME B16.25.
WOL-09 J5 Weldolet; pipe line; carbon steel; ASTM A 694 Gr F70; MSS
SP-97 standard; buttweld ends ASME B16.25.
WOL-11 H14 Weldolet; pipe line; carbon steel; ASTM A 694 Gr F65; MSS
SP-97 standard; buttweld ends ASME B16.25.
WOL-12 E32 F32 Weldolet; pipe line; carbon steel; ASTM A 420 Gr WPL3;
MSS SP-97 standard; buttweld ends ASME B16.25.
WOL-14 J40 Weldolet; pipe line; carbon steel; ASTM B564 (UNS
N06625); MSS SP-97 standard; buttweld ends ASME
B16.25.
WOL-90 B7 B7R Weldolet; pipe line; Cu-Ni 90/10 (UNS C70620); 20 bar
pressure; EEMUA 146 standard; buttweld ends ASME
B16.25.