Professional Documents
Culture Documents
D2n Relay: The Best Rela Tion
D2n Relay: The Best Rela Tion
D2n Relay
108-98007
Rev. C
EC-JM00-0009-03
ECOC: JM10
1. Apr. 04
D2n Relay V23105
Features
– Standard DIL relay
– Dimensions 20.3 x 10.1 x 10.43 mm, 0.800 x 0.400 x 0.450 inch
– Switching and continous current 3 A
– 2 changeover contacts (2 form C / DPDT)
– Single contacts
– Immersion cleanable
– Four different coil sensitivities
(150, 200, 400, > 500 mW)
– Surge voltage resistance meets FCC Part 68 requirement:
1.5 kV (10 / 160 µsec) between coil and contacts
Typical applications
– Communications equipment
– Office equipment
– Measurement and control equipment
– Entertainment electronics
– Medical Equipment
– Consumer electronics
THT
V23105-A5xxx-A201
mm inch
Terminal assignment
Relay - top view
Vdc mA mW W / ± 10 %
2.6 2.6
Umax. at 0 A Umax. at 0 A
2.4 2.4
Umax. at 2 x 1 A Umax. at 2 x 1 A
2.2 Umax. at 2 x 2 A 2.2 Umax. at 2 x 2 A
Coil Voltage [U/Unom]
1.8 1.8
1.6 1.6
1.4 1.4
1.2 1.2
3.0 3.0
400 mW coil 550 mW coil
400 mW 550 mW
2.8 2.8
2.6 2.6
Umax. at 0 A Umax. at 0 A
2.4 2.4
Umax. at 2 x 1 A Umax. at 2 x 1 A
2.2 Umax. at 2 x 2 A 2.2 Umax. at 2 x 2 A
Coil Voltage [U/Unom]
2.0 2.0
Unom. nominal coil voltage
1.8 1.8
Unom. nominal coil voltage
1.6 1.6
1.4 1.4
1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
Uop. min. Uop. min.
0.4 0.4
Urel. min. Urel. min.
0.2 0.2
0.0 0.0
-30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
Ambient Temperature [°C] Ambient Temperature [°C]
Ordering Code
V 2 3 1 0 5 A 5 A 2 0 1
D2n Relay Identification
Version
0 = 150 mW nominal power consumption
3 = 200 mW
4 = 400 mW
5 = 550 mW
Coil number
08 = 3 V nominal voltage (only with 150/200 mW nominal coil power consumption*)
01 = 5 V nominal voltage
02 = 6 V
06 = 9 V
04 = 10 V (only with 500 mW nominal coil power consumption)
03 = 12 V
05 = 24 V
07 = 48 V (not with 150 mW nominal coil power consumption)
BT 47 versions
475 = 5 V nominal voltage
479 = 10 V
476 = 12 V
477 = 24 V
478 = 48 V
Contact assembly
A201 = 2 changeover contacts; silver nickel, gold-plated, against silver nickel, gold-plated
Contact Data
Number of contacts and type 2 changeover contacts
Contact assembly single contacts
Contact material Silver-nickel, gold-covered
Limiting continuous current at max. ambient temperature 3A
Maximum switching current 3A
Maximum swichting voltage 220 Vdc
250 Vac
Maximum switching capacity 60 W, 125 VA
Thermoelectric potential > 10 mV
Minimum switching voltage 100 mV
Initial contact resistance / measuring condition: 10 mA / 20 mV < 100 mW
Electrical endurance at 230 Vac / 0.5 A typ. 3.0 x 105operations
DC current [A]
Insulation
Insulation resistance at 500 Vdc > 109 W
Dielectric test voltage (1 min)
between coil and contacts 1000 Vrms
between adjacent contact sets 750 Vrms
between open contacts 750 Vrms
RF Characteristics
Isolation at 100 / 900 MHz -39.0 dB / -20.7 dB
Insertion loss at 100 / 900 MHz -0.02 dB / -0.27 dB
V.S.W.R. at 100 / 900 MHz 1.04 / 1.40
General data
Operate time at Unom typ. / max. 5 ms / 7 ms
Release time without diode in parallel, typ. / max. 4 ms / 6 ms
Release time with diode in parallel, typ. / max. 7 ms / 10 ms
Bounce time at closing contact, typ. / max. 3 ms / 5 ms
Maximum switching rate without load 20 operations/s
Ambient temperature
150 and 200 mW coil -25° C ... +85° C
400 mW coil -25° C ... +75° C
500 mW coil -25° C ... +60° C
Thermal resistance < 100 K/W
Maximum permissible coil temperature 105° C
Vibration resistance (function) 10 g
10 to 55 Hz
Shock resistance, half sinus, 11 ms 10 g (function)
40 g (damage)
Degree of protection / Environmental protection immersion cleanable, IP 67 / RT III
Needle flame test application time 20 s, burning time < 15 s
Mounting position any
Processing information Ultrasonic cleaning is not recommended
Weight (mass) max. 2.5 g
Terminal coating SnCu 0,7
Resistance to soldering heat 260° C / 10 s
Packing Dimensions in mm
Tube for THT version - 25 relays per tube, 1000 relays per box