Professional Documents
Culture Documents
Conshear: Retrofit Replacement Blades For Oem Belt Cleaners
Conshear: Retrofit Replacement Blades For Oem Belt Cleaners
Correct Location:
Correct Location: 1/8" gap at initial
When blade contact is made against the head pulley (prior to tensioning) there should blade/belt contact
be a 1/16" to 1/8" gap at the bottom of the blade face (Fig. 1).
Fig. 1
Possible Problems:
• Pole location too far out - The initial blade/belt contact Tip pushed
gap will be larger than 1/8" (Fig. 2). If the blade is away from belt
correctly tensioned it may flip through before it is fully Incorrect:
Larger than Incorrect:
worn. If tensioned too lightly, it will develop the “smile 1/8" gap no gap
effect” quickly and not clean properly.
• Pole location too far in - If there is no gap at the initial
blade/belt contact (Fig. 3), the tip of the blade may not be
touching the belt. In this case, the blade will push away
Fig. 2 Fig. 3
and lose its shearing (cleaning) effect. The blade may
also develop a flap at the tip which may trap material.
Correct Tension:
Full contact
between blade
Correct Tensioning: face and belt
The blade should be tensioned until the gap is gone (Fig. 4).
Fig. 4
Belt Width Minus 2" Belt Width Minus 8" Belt Width Minus 14" Material Path
Material Path Material Path
3
Cross-Reference for Replacement of
Martin® QC® #1 Standard Blades
ACTUAL MARTIN® SLOT POLE PLATE CONSHEAR QC#1
BELT BLADE ORDERING CONSHEAR™ PART WEIGHT WIDTH THICKNESS BLADE HEIGHT BLADE HEIGHT
WIDTH LENGTH NUMBER ITEM CODE NUMBER LBS.
7/16" 5/16" 7-1/4" 6-3/4"
12" 10" CRB10 75628 32773-1211 4.6
18" 16" CRB16 75629 32773-1811 7.3
24" 22" CRB22 75630 32773-2411 10.1 ConShear Blade Design
30" 28" CRB28 75631 32773-3011 12.8
36" 34" CRB34 75632 32773-3611 15.5
42" 40" CRB40 75633 32773-4211 18.3
48" 46" CRB46 75634 32773-4811 21.0
54" 52" CRB52 75635 32773-5411 23.8
7-1/4"
60" 58" CRB58 75636 32773-6011 26.5
72" 70" CRB70 75773 32773-7211 32.0
Additional blade sizes are available upon request. Call for pricing.
NOTE: Blade coverage is 2 inches less than belt width. 7/16"
6-3/4"
Martin QC #1 ® ®
7/16"
Note: Also works on Baker-Bohnert Yellow Jacket™ Primary Cleaners.
Martin® QC® #1
Heavy-Duty 9/16"
Martin® and QC® #1 are registered trademarks of Martin Engineering, Neponset, IL.
4 Yellow Jacket™ is a trademark of Baker-Bohnert, Louisville, KY
Cross-Reference for Replacement of
Arch/Gordon Saber® Primary Blades
ACTUAL SLOT POLE PLATE CONSHEAR SABER BLADE
BELT BLADE ORDERING CONSHEAR™ ARCH/GORDON WEIGHT WIDTH THICKNESS BLADE HEIGHT HEIGHT
WIDTH LENGTH NUMBER ITEM CODE PART NUMBER LBS.
7/16" 3/8" 7-1/4" 5-7/8"
18" 16" RBAGS-16 75995 SB-016-18 7.3
24" 22" RBAGS-22 75996 SB-016-24 10.1
ConShear Blade Design
30" 28" RBAGS-28 75997 SB-016-30 12.8
36" 34" RBAGS-34 75998 SB-016-36 15.5
42" 40" RBAGS-40 75999 SB-016-42 18.3
48" 46" RBAGS-46 76028 SB-016-48 21.0
54" 52" RBAGS-52 76029 SB-016-54 23.8
60" 58" RBAGS-58 76030 SB-016-60 26.5 7-1/4"
72" 70" RBAGS-70 76031 SB-016-72 32.0
Additional blade sizes are available upon request. Call for pricing.
NOTE: Blade coverage is 2 inches less than belt width.
7/16"
Arch/Gordon Saber®
7/16"
Note: Also works on Falcon Primary Cleaners.
5-3/4"
6-5/8"
ASGCO® Skalper® IV
9/16"
Argonics Eraser™
9/16"
Note: ConShear blade design is identical to the
ASGCO replacement blade, except for length.
ASGCO® and Skalper® are registered trademarks of ASGCO Mfg, Inc., Allentown, PA.
6 Eraser™ and Raptor™ are registered trademarks of Argonics, Inc., Marquette, MI.
Cross-Reference for Replacement of
Metso/Trellex Stephens-Adamson Blades
BASE BASE CONSHEAR S-A BLADE
ACTUAL WIDTH HEIGHT BLADE HEIGHT HEIGHT
BLADE ORDERING CONSHEAR™ S-A PART WEIGHT
LENGTH NUMBER ITEM CODE NUMBER LBS. 1-31/32" 25/32" 8" 8"
6" R6SA 76570 ABC90 3.1
Blades fit into cartridge that mounts on the pole.
ConShear Blade Design
8"
25/32"
S-A Pre-Cleaner
5-7/8" 1-33/64"
1-31/32"
6" 1/4"
8-1/4"