Professional Documents
Culture Documents
ANChor Design
ANChor Design
ANChor Design
70
www.hilti.in
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Specifier's comments:
1 Anchor Design
1.1 Input data
Anchor plate
CBFEM
: lx x ly x t = 250.0 mm x 250.0 mm x 12.0 mm;
CBFEM
- The anchor calculation is based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
3 4
Anchor reactions [kN]
Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 4.477 0.507 0.506 0.018 Compression
2 4.510 0.494 0.494 0.013 x
3 4.481 0.507 0.506 -0.018
Tension
4 4.509 0.494 0.494 -0.013
Anchor forces are calculated based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
N
NSd £ NRd,s = Rk,s ETAG 001 Annex C, Table 5.2.2.1
gM,s
y c · NRk,p
NSd £ NRd,p = ETAG 001 Annex C, Table 5.2.2.1
gM,p
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
N
NSd £ NRd,c = Rk,c ETAG 001 Annex C, Table 5.2.2.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N ETAG 001 Annex C, Eq. (5.2)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef ETAG 001 Annex C, Eq. (5.2a)
0
Ac,N = scr,N · scr,N ETAG 001 Annex C, Eq. (5.2b)
c
y s,N = 0.7 + 0.3 · 1.00 ETAG 001 Annex C, Eq. (5.2c)
ccr,N £
hef
y re,N = 0.5 + 1.00 ETAG 001 Annex C, Eq. (5.2d)
200 £
1
y ec1,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec1,N £
1+
scr,N
1
y ec2,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec2,N £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm]
230,400 90,000 150.0 300.0
Group anchor ID
1-4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
V
VSd £ VRd,s = Rk,s ETAG 001 Annex C, Table 5.2.3.1
gM,s
V
VSd £ VRd,cp = Rk,cp ETAG 001 Annex C, Table 5.2.3.1
gM,c,p
VRk,cp = k · NRk,c ETAG 001 Annex C, Eq. (5.6)
0 A
NRk,c = NRk,c · 0c,N · y s,N · y re,N · y ec1,N · y ec2,N ETAG 001 Annex C, Eq. (5.2)
Ac,N
0 1,5
NRk,c = k1 · √fck,cube · hef ETAG 001 Annex C, Eq. (5.2a)
0
Ac,N = scr,N · scr,N ETAG 001 Annex C, Eq. (5.2b)
c
y s,N = 0.7 + 0.3 · 1.00 ETAG 001 Annex C, Eq. (5.2c)
ccr,N £
hef
y re,N = 0.5 + 1.00 ETAG 001 Annex C, Eq. (5.2d)
200 £
1
y ec1,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec1,V £
1+
scr,N
1
y ec2,N = 1.00 ETAG 001 Annex C, Eq. (5.2e)
2 · ec2,V £
1+
scr,N
2 0 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k-factor
230,400 90,000 150.0 300.0 2.000
Group anchor ID
1-4
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
V
VSd £ VRd,c = Rk,c ETAG 001 Annex C, Table 5.2.3.1
gM,c
0 Ac,V
VRk,c = VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V ETAG 001 Annex C, Eq. (5.7)
Ac,V
0 a b 1,5
VRk,c = k1 · dnom · lf · √fck,cube · c1 ETAG 001 Annex C, Eq. (5.7a)
0,5
a = 0.1 · () lf
c1
ETAG 001 Annex C, Eq. (5.7b)
0,2
= 0.1 · (
c )
d nom
b ETAG 001 Annex C, Eq. (5.7c)
1
0 2
Ac,V = 4.5 · c1 ETAG 001 Annex C, Eq. (5.7d)
c2
y s,V = 0.7 + 0.3 · 1.00 ETAG 001 Annex C, Eq. (5.7e)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 ETAG 001 Annex C, Eq. (5.7f)
√
1
2
y a,V =
(cos aV) +
2
(sin2.5a )
V ³ 1.00 ETAG 001 Annex C, Eq. (5.7g)
1
y ec,V = 1.00 ETAG 001 Annex C, Eq. (5.7h)
2 · ec,V £
1+
3 · c1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
1.5 Combined tension and shear loads (ETAG, Annex C, Section 5.2.4)
Steel failure
a a
bN + bV £ 1.0
1.6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates as per current regulations (ETAG 001/Annex C, EOTA
TR029, etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor
plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering calculates
the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions explained above.
The proof if the rigid base plate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be checked for
agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the anchor plate without creating air voids and before application of the loads.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• The anchor design methods in PROFIS Engineering require rigid anchor plates, as per current regulations (AS 5216:2018, ETAG 001/Annex
C, EOTA TR029 etc.). This means that the anchor plate should be sufficiently rigid to prevent load re-distribution to the anchors due to
elastic/plastic displacements. The user accepts that the anchor plate is considered close to rigid by engineering judgment."
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Hilti HSA stud anchor with 114 mm embedment, M12 hnom3, Steel galvanized, installationwith torque control bar per ETA 11/0374
y
125.0 125.0
35.0
3 4
125.0
180.0
x
125.0
1 2
35.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
2.2 Summary
Description Profile Stiffeners Anchor plate Welds [%] Concrete
[%]
sEd [N/mm²] ePl [%] sEd [N/mm²] ePl [%] sEd [N/mm²] ePl [%] Hole bearing
[%]
1 Combination 17.64 0.00 40.39 0.00 28.86 0.00 1 24 441
1
2.3 Anchor plate classification
Results below are displayed for the decisive load combinations: Combination 1
Anchor tension forces Equivalent rigid anchor plate (CBFEM) Component-based Finite Element Method
(CBFEM) anchor plate design
Anchor 1 2.747 kN 4.477 kN
Anchor 2 2.753 kN 4.510 kN
Anchor 3 2.747 kN 4.481 kN
Anchor 4 2.753 kN 4.509 kN
User accepted to consider the selected anchor plate as rigid by his/her engineering judgement. This means the anchor design guidelines can
be applied.
2.4 Profile/Stiffeners/Plate
Profile and stiffeners are verified at the level of the steel to concrete connection. The connection design does not replace the steel design for
critical cross sections, which should be performed outside of PROFIS Engineering.
Limit state criteria as per IS 800, sEd <= fy, ePl <= elim.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Results
Part Load Material sEd [N/mm²] ePl [%] fy [N/mm²] gM0 fy/gM0 elim [%] Status
combination [N/mm²]
Plate Combination E 165 (Fe 28.86 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Profile Combination E 165 (Fe 7.47 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Profile Combination E 165 (Fe 17.64 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Profile Combination E 165 (Fe 16.55 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Profile Combination E 165 (Fe 16.52 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Stiffenera Combination E 165 (Fe 40.27 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Stiffenerb Combination E 165 (Fe 40.32 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Stiffenerc Combination E 165 (Fe 40.39 0.00 165.00 1.10 150.00 5.00 OK
1 290)
Stiffenerd Combination E 165 (Fe 40.34 0.00 165.00 1.10 150.00 5.00 OK
1 290)
150.00 N/mm²
0.00 N/mm²
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
5.00%
0.00%
2.4.2 Hole bearing
Decisive load combination: 1 - Combination 1
Plate hole bearing resistance, IS 800 section 10.3.4:
Equations
Vndpb
Vdpb =
gmb
Vndpb = 2.5kbdtfu
Vsb
Utilization =
Vdpb
Variables
kb e [mm] p [mm] d0 [mm²] d [mm²] t [mm] fu [N/mm²] gmb
Anchor 1 0.83 35.0 ∞ 14.0 12.0 12.0 290.00 1.25
Anchor 2 1.00 215.1 180.0 14.0 12.0 12.0 290.00 1.25
Anchor 3 0.83 35.0 ∞ 14.0 12.0 12.0 290.00 1.25
Anchor 4 1.00 215.1 180.0 14.0 12.0 12.0 290.00 1.25
Results
Vndpb [kN] Vsb [kN] Vdpb [kN] Utilization [%] Status
Anchor 1 87.054 0.507 69.643 1 OK
Anchor 2 104.400 0.494 83.520 1 OK
Anchor 3 87.054 0.507 69.643 1 OK
Anchor 4 104.400 0.494 83.520 1 OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 12
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
2.5 Welds
Profiles are modeled without taking the corner radius into account. Special rules for welding (e.g. for cold-formed profiles ...) are not taken into
account by the software.
The ultimate stress of the welding electrodes selected should be verified.
The verification of full penetration butt welds is not carried out, as it is assumed that the weld material has the same, or larger resistance than
both parent materials (welds, plate or profile), as per IS 800, section 10.5.7.1.2.
Equations
fu
fe = √(fa2 + 3q2) ≤ fwd =
√3gmw
fe
Utilization =
fwd
Variables
Edge l [mm] tt [mm] tl [mm] fa [N/mm²] q [N/mm²] fu [N/mm²] gmw
Member 1-tfl 1 60.8 6.0 8.5 4.47 0.86 290.00 1.25
Member 1-bfl 1 60.8 6.0 8.5 4.41 1.25 290.00 1.25
Results
Edge fe [N/mm²] fwd [N/mm²] Utilization [%] Status
Member 1-tfl 1 4.71 133.95 4 OK
Member 1-bfl 1 4.91 133.95 4 OK
Equations
fu
fe = √(fa2 + 3q2) ≤ fwd =
√3gmw
fe
Utilization =
fwd
Variables
Edge l [mm] tt [mm] tl [mm] fa [N/mm²] q [N/mm²] fu [N/mm²] gmw
Stiffenera 49.9 4.0 5.7 16.77 15.02 290.00 1.25
Stiffenera 1 49.9 4.0 5.7 16.76 10.04 290.00 1.25
Stiffenerb 49.9 4.0 5.7 16.74 10.12 290.00 1.25
Stiffenerb 1 49.9 4.0 5.7 16.75 15.10 290.00 1.25
Stiffenerc 49.9 4.0 5.7 17.54 10.44 290.00 1.25
Stiffenerc 1 49.9 4.0 5.7 17.36 15.32 290.00 1.25
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
12
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 13
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Results
Edge fe [N/mm²] fwd [N/mm²] Utilization [%] Status
Stiffenera 30.96 133.95 23 OK
Stiffenera 1 24.14 133.95 18 OK
Stiffenerb 24.23 133.95 18 OK
Stiffenerb 1 31.06 133.95 23 OK
Stiffenerc 25.20 133.95 19 OK
Stiffenerc 1 31.71 133.95 24 OK
Stiffenerd 31.57 133.95 24 OK
Stiffenerd 1 25.03 133.95 19 OK
2.6 Concrete
Decisive load combination: 1 - Combination 1
The concrete should have sufficient reinforcement to take into account the tensile forces that develop due to the fixture attachment. The
definition of the reinforcement in the concrete is out of scope of PROFIS Engineering.
2.6.1 Compression in concrete under the anchor plate, IS800, section 7.4
1.79 N/mm²
0.00 N/mm²
Equations
N
s = A
1
s ≤ 0.6fck
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
13
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 14
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Variables
fck [N/mm²] A1 [mm²] N [kN]
35.00 79 7.269
Results
s [N/mm²] 0.6fck [N/mm²] Utilization [%] Status
92.50 21.00 441 NOT OK
2.8 Warnings
● By using the CBFEM calculation functionality of PROFIS Engineering you may act outside the applicable design codes and your specified
anchor plate may not behave rigid. Please, validate the results with a professional designer and/or structural engineer to ensure suitability
and adequacy for your specific jurisdiction and project requirements.
● The anchor is modeled considering stiffness values determined from load displacement curves tested in an independent laboratory.
Please note that no simple replacement of the anchor is possible as the anchor stiffness has a major impact on the load distribution
results.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
14
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 15
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
3 Summary of results
Design of the anchor plate, anchor, welds and other elements are based on CBFEM (component based finite element method) and Eurocode
regulations.
Load combination Max. utilization Status
Anchors Combination 1 18% OK
Anchor plate Combination 1 18% OK
Welds Combination 1 24% OK
Stiffeners Combination 1 25% OK
Concrete Combination 1 441% NOT OK
Profile Combination 1 11% OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
15
Hilti PROFIS Engineering 3.0.70
www.hilti.in
Company: Page: 16
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jul 7, 2021 Date: 07/07/2021
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2021 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
16