Professional Documents
Culture Documents
Performance and Specifications: 1) Rated Load & Input Signals
Performance and Specifications: 1) Rated Load & Input Signals
Performance and Specifications: 1) Rated Load & Input Signals
▶ Input Signals
1. GENERAL
STICS of KORANDO SPORTS, called as RKSTICS (REKES + STICS (Super Time & Integrated
Control System)), is almost the same as that of ACTYON SPORTS in terms of its function and
role.
Chime
AUTO
Operates automatically
according to the vehicle
speed or the amount of rain.
LO HI
Continuous wipe, slow Continuouswipe, fast operation
operation.
Previous model
Pressing the switch makes washer
fluid to be sprayed for 2 sec. with
four wiping, after having delay of 0.6
sec., washer fluid to be sprayed for
1.5 sec. with three wiping
Front Wiper and Washer Coupled Operation
Pull the lever briefly (below 0.6 seconds):
New model One wiping cycle without washer spray
Pressing the switch makes washer Pull and hold the lever for more than 0.6 seconds:
fluid to be sprayed for 2 sec. with Three wiping cycles with washer spray
four wiping, and washer fluid to be
sprayed for 1.5 sec. with three
wiping, with no delay of time
02-8
2) Operation Logic
▶Wiper MIST and Front Washer Coupled Wiper
- The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for 0.1 to 0.59 seconds with the ignition switch "ON".If the wiper parking
terminal gets off, the wiper relay is turned off.
- The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is
turned on for more than 0.6 seconds with the ignition switch "ON". The wiper relay gets on
3 times immediately after turning off the washer switch.
8710-01 02-9
- When the washer switch is turned on for more than 0.6 seconds during the wiper
operation by INT switch, the operation in step (2) is performed.
When it is turned on for a certain period of time (0.1 to 0.59 seconds), the operation in
step (1) is performed.
02-10
- The auto washer switch input is overridden during the washer coupled wiper operation.
- The auto washer switch input is overridden during the auto washer coupled wiper
operation.
- The auto washer switch input is overridden during the rain sensor coupled wiper or vehicle
speed sensitive INT wiper operation.
- When the auto INT switch input is received during the auto washer operation, the auto
washer operation stops and the auto INT operation is activated.
02-12
▶System layout
8710-01 02-13
A sensor that emits infrared rays through LED AUTO: Wiper operates automatically by rain
and then detects the amount of rain drops by sensor
receiving reflected rays against sensing section FAST↔SLOW: Auto delay/Auto speed control. A
(rain sensor mounting section on the position that can control sensitivity against rains
windshield) with photodiode (auto light sensor on the windshield and transmits wiping demand
integrated type) signal accordingly
02-14
▶Sensitivity Control
- The wiper LOW relay is turned on and the wiper motor runs one cycle when the volume
sensitivity is increased (ex: sensitivity 0 ⇒ 1) while the ignition switch and the INT switch is
in the "ON" position, and the wiper motor is in "Parked" position). However, the wiper motor
can be operated only when the rain sensor detects the "Rain Detected" signal.
※ If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor
runs only one cycle.
02-16
- When the parking terminal is fixed to IGN, the wiper system outputs the wiper operating
signal for 2 seconds, then continuously outputs the wiper parking signal.
※The wiper motor runs only when the rain sensor requires the wiper operation.
8710-01 02-17
- The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction signal from the rain
sensor, while the ignition key is in "ON" position and the wiper switch is in "ON" position.
02-18
▶ TROUBLE SHOOTING
Symptom 1. The wiper does not operate one cycle when turning the multifunction
wiper switch to the "AUTO"from the "OFF"position or starting the engine
while the wiper switch is in the "AUTO"position.
1) When starting the engine with the multifunction wiper switch in the "AUTO" position,
the wiper operates one cycle to remind a driver that the wiper switch is in the "AUTO"
position.
2) When the multifunction wiper switch is turned to "AUTO" from "OFF", the wiper
operates one cycle.
It always operates one cycle for the initial operation, however, the wiper does not
operate afterwards to prevent the wiper blade wear if not raining when turning the
wiper switch to "AUTO" from "OFF". However, the wiper operates up to 5 minutes
after rain stops. If this function does not occur, check No. 8 pin. If the pin is normal,
check the wiper relay related terminals.
Symptom 2. It rains but the system does not work in "AUTO" position.
Check whether the variable resistance knob on the multifunction wiper switch is set in
"FAST". The "FAST" is the highest stage of sensitivity and very sensitive to small amount
of rain drops. Therefore, change the knob to low sensitivity.
Symptom 4. The wiper operates continuoulsy even on the dry windshield glass.
1) Check the wiper blade for wear. If the wiper blade cannot wipe the glass uniformly
and clearly, this problem could be occurred. In this case, replace the wiper blade
with new one.
2) Check whether the variable resistance knob on the multifunction wiper switch is set
in "FAST" The "FAST" is the highest stage of sensitivity and very sensitive to small
amount of rain drops. Therefore, change the knob to low sensitivity.
8710-01 02-19
Symptom 5. The wiper does not operate at high speed even in heavy rain.
If the wiper does not operate at high speed even in heavy rain, check the pins 1 and 2.
In other words, the wiper should operate at high speed when grounding the pins 1 and
2.
Check whether the variable resistance knob on the multifunction wiper switch is set in
"FAST" or "SLOW".
Notify that the customer can select the sensitivity by selecting the variable resistance
value. And, select a proper stage.
02-20
- Rain detected headlamp: If it rains heavy which requires the highest INT speed (almost
LOW), the headlamps are turned on automatically.
- Night detected wiping: When the auto light control turns on the headlamps and the rain
sensor detects the rain, the wiper sensitivity is automatically increased by one level in
comparison with daytime.
(i.e. the AUTO wiper switch is at the 3rd level, but the wiper operates at the 4th level.)
Emitter lens
The LED emitting the infrared
rays is installed on the bottom
and the lens guides the
infrared rays to target point.
- Controls the wiper intermittent operation by the values from the vehicle speed and the
volume (resistance).
˙ Calculates and converts the Intermittent interval automatically by obtaining the INT
VOLUME when the ignition switch and the INT switch is in the "ON" position.
˙ The wipers are operated in vehicle speed sensitive mode when turning the INT switch to
the "ON" position with the engine running or starting the engine with the INT switch
positioned to "ON".
˙ Intermittent interval (at 0 km/h): 3 ± 0.5 ~ 19 ± 2 seconds
- Vehicle speed calculation
60 [km/h] × 60 [sec]
1 [PULSE/SEC] = ≒ 1.41 [km/h]
637 × 4 PULSE
- VOLUME calculation
˙ The pause time of the vehicle speed sensitive INT wiper is calculated by the INT volume
(input voltage). Each level has the hysteresis.
˙ Pause time means the duration that wipers are stopped at parking position.
˙ Elapsed time means the duration after the wiper motor started to operate from parking
position.
˙ The pause time is calculated by the vehicle speed and the VOLUME.
※If the pause time is below 1.0 second, the wipers operate without pause.
※If the pause time is over 1.5 seconds, the wipers operate intermittently.
02-22
STICS
Chime Buzzer
PAS buzzer
Since the luggage room tailgate does not have the door switch, the door ajar warning light
does not come on when it is open.
02-28
The seat belt warning light blinks and the chime buzzer sounds for 6 seconds when turning the
ignition key to "ON" without fastening the seat belt. After fastening the seat belt, the chime buzzer
stops.
8710-01 02-29
Center Room
Lamp
(Lamp: ON)
With diesel and gasoline engine With diesel engine With gasoline engine
The defogger system uses the heated glass to remove the moisture and frost on the windows,
which can disturb safe driving.
The defogger (including de-icer) activates the corresponding switch and the STICS controls the
operating time.
T2: 0.5 s
(*1) LOCK: Driver's & Passenger's & Rear door & = Lock
8710-01 02-43
- DOOR OPEN: Any of all door switches (including engine hood, driver's door, passenger's
door or rear door) is in "OPEN" position.
- DOOR CLOSE: All door switches (including engine hood, driver's door, passenger's door,
rear door and tailgate) are in "CLOSE" position.
- The door lock/unlock operation does not affect the engine hood.
- OPEN/CLOSE of the dech tailgate does not affect entering the armed mode.
In other words, when the hood and front/rear door are closed even if the dech tailgate is
open, the vehicle can enter the armed mode.
- DOOR LOCK: Indicates that driver's, passenger's and rear door and tailgate lock switches
are in LOCK positions.
- DOOR UNLOCK: Indicates that driver's, passenger's or rear door or tailgate lock switches
are in UNLOCK positions.
Since the luggage room tailgate does not have the door switch, the door ajar warning light
does not come on when it is open.
02-46
The theft deterrent horn and hazard warning flasher is activated when fitting the battery in armed mode.
(The same operation as when alarm condition is met in armed mode is performed.)
▶ PANIC Warning
1. The PANIC warning output is "ON" for 27 seconds using the horn and hazard warning
flasher, when receiving the PANIC signal from the remote control key.
2. The PANIC warning output is "OFF" when pressing any button on the remote control key
during PANIC warning.
3. The followings are about the theft deterrent warnings.
a. The theft deterrent warning is deactivated when receiving PANIC signal from the
remote control key during theft deterrent warning.
b. The theft deterrent warning output is "ON" when the theft deterrent conditions are
established during PANIC warning (PANIC output is "OFF").
c. The PANIC warning output is "ON" when receiving the PANIC signal from the remote
control key in Armed Ready / Armed / Warning Completion / Relock Ready mode
(maintaining the theft deterrent mode).
4. This function operates only in armed mode.
8710-01 02-49
1. When the automatic hazard warning lamp switch is pressed for approx. 0.1 to 0.59
seconds, the hazard warning lamp blinks 3 times at an interval of 0.35 seconds.
2. When the automatic hazard warning lamp switch is pressed for approx. 0.6 seconds or
longer, the hazard warning lamp blinks 10 times at an interval of 0.35 seconds.
3. This function is only available when the ignition key is in the "ON" position.
4. If the ignition key is turned to the "OFF" position during this function is activated, this
function is immediately deactivated.
5. If the system receives signals for the turn signal lamp operation during this function is
activated, this function is immediately deactivated.
6. While the turn signal lamp signals are already inputted, pressing the automatic hazard
warning lamp switch does not activate the automatic hazard warning lamp function.
LED flasher
Briefly press: blink once
Press and hold: blink twice
Battery Replacement
Battery
REKES key
Immobilizer &
charging key
02-52
▶ Specification of Receiver
1. Operating requirements
- You should remove the ignition key.
- You can register the code only using the diagnostic device.
1. All doors are locked when briefly pressing the door LOCK burron on remote control key (less
than 0.5 seconds).
2. The system outputs LOCK signal immediately after receiving the door lock message from the
remote control key. The system activates the theft deterrent mode when all doors are locked
while they are fully closed (the hazard warning lamps blink twice.).
8710-01 02-53
▶ Door Unlock
1. The door unlock operates when pressing the door switch on the remote control key for longer
than 0.5 seconds.
2. The door unlock relay is "ON" for 0.5 seconds when receiving the door unlock message from
the remote control key.
3. The hazard warning lamps blink once only when all the doors unlocked successfuly.
02-54
▶ Remote Panic
1. If you press and hold the door UNLOCK and PANIC button (more than 2 seconds) on the
remote control key, the panic function is activated.
2. The vehicle activates the panic alarm by using the horn and hazard warning lamp for 27
seconds when receiving the panic message from the remote control key.
8710-01 02-55
▶ Remote Escort
1. When you press and hold the door LOCK button (more than 0.5 seconds) the escort function
is activated.
2. The headlamp comes on for 20 seconds and goes off automatically, when the escort
message is received from the remote control key.
1. If no door is opened for 30 seconds after inputting remote door unlock, the doors are
automatically locked and the armed mode of anti-theft system is activated again (RELOCK
function).
02-56
1. If you press the folding/unfoling switch with the ignition switch in "ON" position, the outside
rearview mirror is folded or unfolded depending on the previous status. At this time,
folding/unfolding outputs are maintained for about 15 to 17 seconds.
2. Even though the ignition switch is turned to "OFF" position during folding/unfolding output,
the output continues on for remaining time.
3. When removing and refitting the battery, the first switch input folds the mirror.
4. If you turn the ignition switch to the "OFF" from "ON" position, operating time is extended by
60 seconds. Unlikely the previous model, opening the front door does not affect the
extension time. (i.e., opening/closing the front door is irrelevant)
5. If the unfolding input is received from the switch during folding output or the folding input is
received during unfolding output, the existing output stops and new output is activated after
the delay time of about 0.1 second.
6. When the vehilce speed is above 50 km/h with the mirror unfolded, even though the folding
signal is received it is overridden.
(folding is possible only at vehicle speed of less than 50 km/h )
8710-01 02-57
In order to prevent the driver from getting off the vehicle with the sunroof open, the reminder
function for the driver is added. This function is activated as follows:
1. If you remove the ignition switch and open the driver's door with the sunroof open, the chime
buzzer sounds.
2. As soon as you close the driver's door or the sunrooof, the chime buzzer output stops.
3. However, when operating conditions in step (1) are met after the operation in step (2), the
chime buzzer will not sound again. If you turn the ignition swtich to the "ON" position again
and the operating contions in step (1) are met, the chime buzzer sounds again.
4. If the operating condtions for door ajar warning and sunroof open warning are met at the
same time, the sunroof open warning is activated preferentially.
02-58
4. CIRCUIT DIAGRAM
▶ Circuit Diagram for Wiper
8710-01 02-59
The door ajar warning lamp in the instrument cluster does not come on even though the
tailgate is opened.
02-60
1. Connect the diagnostic device to the vehilce and select the vehicle type and system (RK-
STICS). When the following screen is displayed, select 'REMOCON CODING'.
2. Remove the remote control key from the ignition key box and press 'Next'. Press the door
UNLOCK (PANIC) button on the remote control key once (for approx. 2 seconds or longer).
02-62
3. The first key coding completion screen is displayed with beep sound as follows: Press 'Next'
and perform the second remote control key coding in the same way.
4. When the second key coding is completed, the following screen is displayed. Finish the
remote control key coding by pressing 'Previous'.
5. Exit the diagnostic screen, remove the device from the diagnostic connector and perform the
function test for the remote control key. If it does not work well, perform the above procedures
again.
6. If another key should be registered additionally, insert the second key into the key cylinder and
press "Next" within 10 seconds since the first transponder coding is complete.
0000-00 02-65
If the registration fails, press "Previous" button and perform the registration procedures again.
02-66
The REKES key coding is not performed by connecting the REKES coding terminal (No. 15) of
the diagnostic connector to the jump wire between the ground terminals.
(possible only diagnostic device)